PUZ HA Engineering Manual Section
P-SERIES COMMERCIAL SYSTEMS
PUZ HYPER HEAT PUMP OUTDOOR UNITS
1. Specifications................................................................................................................................................ PUZ-HA-2
2. External Dimensions..................................................................................................................................... PUZ-HA-6
3. Center of Gravity........................................................................................................................................... PUZ-HA-7
4. Electrical Wiring Diagrams............................................................................................................................ PUZ-HA-8
5. Refrigerant System Diagrams....................................................................................................................... PUZ-HA-9
6. Sound Pressure Levels............................................................................................................................... PUZ-HA-10
7. Standard Operation Range..........................................................................................................................PUZ-HA-11
8. Accessories................................................................................................................................................. PUZ-HA-12
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-1
1. SPECIFICATIONS
INVERTER-driven compressor varies speed dynamically to adapt continuously to the room load.
• R410A refrigerant
• INVERTER technology for maximum energy-efficiency, precise temperature control, and more consistent comfort
in every space
• Innovative flash technology enables high heating capacity at lower outside temperatures
• Exhibits 100% of rated heating capacity at 5º F; 90% of rated heating capacity at -4º F
• Indoor unit powered by outdoor unit
• Rugged housing, tough cabinet finish, strong welds at numerous stress point
• Standard air filter is included with indoor unit; high-efficiency filter is available as an option
• Optional hand-held wireless remote controller with receiver kit is available with or without i-see sensor
• Easy interior access to every P-Series unit
• Durable, aerodynamic fan design
• L-shape condenser coil features copper tubing and aluminum fins
• Cabinet mounting and construction are designed to withstand 155 MPH winds
• Limited warranty; five years parts and seven years compressors
Due to continuing improvement, above specification may be subject to change without notice.
PUZ-HA-2
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
CATIONS
SPECIFICATIONS
4
SPECIFICATIONS

1. SPECIFICATIONS


Model Name



  









 
 

 
 


  
 

 
  

 
  

 
 

  
 
 








 
 







 
 


 
    





 

    






 (ECM)
 















  
 




 
 
 
 
 
 

  


 
 


 
 


 
 


 
 

  
 
 



 
 










 


 


  





 




 


 





 





 
 


 

 




 
     

  
  
 



 


 
 
 
 

 


 

 
 



 








  
  
 







  
  
  




 
 
 




  






  
 








 
 
 
 








  
  
 







  
  
  




 
 
 




  






  
 








 
 
 
 
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-3
DATA
PUZ-HA-4
 
 
 
 




 
 


 
 











   
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.







 




5-3. NOISE CRITERION CURVES
 
 
 
Model Name
 
 
 
 
 
 
 
   






 
 







 
 


         
 
 


5-2. COMPRESSOR TECHNICAL DATA


Model Name


5-1. REFILLING REFRIGERANT CHARGE (R410A : oz, kg)
5
 
 


 
 



 
 


 
 


1. SPECIFICATIONS
REFILLING REFRIGERANT CHARGE (R410A : oz, kg)
1. SPECIFICATIONS
EFFICIENCY RATINGS
Outdoor Unit
COP
COP
COP
@ 47° F @ 17° F @ 5° F
Energy
Star
SEER
EER
HSPF
PUZ-HA30NHA4 PKA-A30KA4
16.5
12
9.5
3.2
2.17
1.62
Yes
PUZ-HA30NHA4 PLA-A30BA4
15.6
12.2
9.4
2.73
2.05
1.41
Yes
PUZ-HA30NHA4 PCA-A30KA4
16.1
12.1
9.3
3.14
1.97
1.6
Yes
PUZ-HA30NHA4 PEAD-A30AA4
16.5
12
9.5
3.4
2.14
1.73
Yes
PUZ-HA36NHA4 PKA-A36KA4
16.2
12
10
3.27
2.2
1.64
Yes
PUZ-HA36NHA4 PLA-A36BA4
17
12.6
10
3.45
2.28
1.9
Yes
PUZ-HA36NHA4 PCA-A36KA4
16.6
12.1
10.3
3.41
2.27
1.7
Yes
PUZ-HA36NHA4 PEAD-A36AA4
PEA-A18AA4 +
PUZ-HA36NHA4
PEA-A18AA4
16.8
12.1
10.4
3.52
2.42
1.82
Yes
16.8
12.5
10.4
3.52
2.5
1.82
Yes
Note:
Indoor Unit
Tax
Credit
Yes
Yes
Efficiency values based on AHRI 210/240 test method.
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-5
PUZ-HA-6
© 2013 Mitsubishi Electric US, Inc.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
Due to continuing improvement, above specification may be subject to change without notice.
10






















Entire mounting flange must be supported.
No cantilevering about bolt hole of mounting
flange allowed.



STEEL BY OTHERS










  

  







PUZ-HA30NHA4
PUZ-HA36NHA4
PUZ-A30/36NHA4
PUZ-A30/36NHA4-BS
Unit : mm<inch>
Unit: mm<inch>
2. EXTERNAL
DIMENSIONS
AND DIMENSIONS
6 OUTLINES
3. CENTER OF GRAVITY
Unit: mm<inch>
PUY-A24/30/36NHA4,A42NHA5
PUY-A24/30/36NHA4,A42NHA5-BS
X
Un
Model name
PUZ(Y)-A12/18NHA
PUZ(Y)-A24/30/36NHA
Z
PUZ(Y)-A42NHA
Y
Unit: inch (mm)
Model name
PUZ-HA30/36NHA (-BS)
X
Y
Z
23-15/64 (590)
7-9/32 (185)
15-55/64 (403)
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-7
X
20-5/64
(510)
23-15/64
(590)
23-15/64
(590)
6
(
7
(
7
(
4. ELECTRICAL WIRING DIAGRAMS
PUZ-A30/36NHA4-BS
NAME
Terminal Block<Power Supply, Indoor/Outdoor >
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Low Pressure Switch
Solenoid Valve (Bypass Valve)
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Heatsink>
Electronic Expansion Valve
Reactor
Active Filter Module
Main Smoothing Capacitor
Capacitor
SYMBOL
P.B.
TABU/V/W
TABS/T
TABP1/P2/P
TABN1/N2/N
DS2, DS3
IPM
N.F.
LI / LO
NI / NO
EI, E2
52C
C.B.
SW1
NAME
Power Circuit Board
Connection Terminal<U/V/W-Phase>
Connection Terminal <L/N-Phase>
Connection Terminal<DC Voltage>
Connection Terminal<DC Voltage>
Diode Bridge
Power Module
Noise Filter Circuit Board
Connection Terminal<L-Phase>
Connection Terminal<N-Phase>
Connection Terminal<Ground>
52C Relay
Controller Circuit Board
Switch<Forced Defrost, Defect History Record
Reset, Refrigerant Address>
Switch<Test Operation>
Switch<Function Switch>
SW4
SW5
SYMBOL
SW6
SW7
SW8
SW9
SWP
CN31
SS
CNM
CNMNT
NAME
Switch<Model Select>
Switch<Function Setup>
Switch<Function Setup>
Switch
Switch<Pump Down>
Connector<Emergency Operation>
Connector<Connection for Option>
Connector<A-Control Service Inspection Kit>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
CNVMNT
<Connected to Optional M-NET Adapter Board>
Connector < Connected for Option (Contact Input)>
CNDM
Connector < Connected for Option (Signal output)>
CN51
LED<Operation Inspection Indicators>
LED1,LED2
Fuse< T6.3AL250V>
F1~F4
X51,X52,X55 Relay
When M-NET adapter (PAC-SF82MA-E) is connected
LEV-C
63L
LEV-A
LEV-B
M
M
TH33 TH32 TH7 TH6 TH3 TH4
C. B.
t°
3
1 2
t°
t°
12
2 1
TH33 TH32 TH7/6 TH3 TH4
(YLW) (BLK) (RED) (WHT) (WHT)
CNF2
(WHT)
1
1
63L
(RED)
3
63H
(YLW)
3
TRANS
2
1
3
LEV-A
(WHT)
6
LEV-B
(RED)
3
2
3
1
LEV-C
(BLU)
6
21S4 3
(GRN)
1
2
3
1 SV2
3
(BLU)
21S4
1
LED4
2
1
M-NET ADAPTER
CN2M
(WHT)
3
A B S
TB7
1
M-NET
5
SS
(WHT)
SV
BLU
N. F.
NO
52C
CNDC
(PNK) 2
6
1
2
TABN1
BLK
L1
RED
L2
1
P
N1
N2
BLK
Io
6
L1
RED
L2
GR
WHT
SW5-6 w2
SW6
ON
OFF
36N
ON
OFF
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
ON
OFF
ON
OFF
EI
U
BRN
S2
S3
CY1
CY2
TB1
INDOOR
UNIT
ACTM
w1MODEL SELECT
S1
ORN
GRN
YLW
4
BLU
DCL
30N
NI
RED
MC
MODEL
U
LI
BLU
W
M-NET ADAPTER
NAME
Terminal Block<M-net connection>
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting : 1s digit>
Switch<Address setting : 10s digit>
LED<Power Supply : DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission : Sending>
LED<Transmission : Recelving>
LED<Power Supply : DC12V>
1
RED
MS
3~
2
CN5
(RED)
CNAC1
(WHT)
WHT
V
2
1
3
U
SYMBOL
TB7
CN5
CND
CN2M
SW1
SW11
SW12
LED1
LED2
LED3
LED4
LED5
BLK
1
2
1
2
TABP
BLK
E2
U
TABN2
RED
CNAC2
(RED)
WHT
CB
WHT
BLK
WHT
CN5
(RED)
CN4
(WHT)
TABN
TABS
1
TABW
2
DS2
TABP1 RED
WHT TABV
BLK
t° 2
TABP2
TH8
BLU
3
IPM
RED
CN2
(WHT)
7
1 CN3
2 (WHT)
TABT
3
1
RED TABU
7
DS3
2
1
CN52C
(BLK)
P. B.
CNAF
(WHT)
CND
(WHT)
3 1
3
1
LO
1
SW12
LED3
w1
WHT
4
SW1
CN31
7
F4
4
14
1 2
X52
1
F1
1
5
CN52C
(RED)
2 1
7
1
CNM
(WHT)
5
F3
CNAC
(WHT)
3
CNVMNT CNMNT
(WHT) (WHT)
1
2
F2
1
CN4
(WHT)
CN2
(WHT)
CNDC 1
(PNK)
CNS
(WHT)
1
6
SW1 SW6
1
CN51 CNDM
(WHT) (WHT)
4
SW4 SWP SW8 SW5
1
X51
1
SW11
CN5
(WHT)
1
LED2
5
5
5
t°
X55
MF2 1
MS
3~
t°
LED1
7
t°
5
3
w1
CNF1
(WHT)
LED2
7
MF1 1
MS
3~
M
SW9 SW7
63H
LED1
[LEGEND]
SYMBOL
TB1
MC
MF1, MF2
21S4
63H
63L
SV
TH3,TH32,TH33
TH4
TH6
TH7
TH8
LEV-A, LEV-B,LEV-C
DCL
ACTM
CB
CY1, CY2
LED5
PUZ-A30/36NHA4
POWER SUPPLY
208/230V 60Hz
wUse copper supply wires.
1 2 3 4 5 6
1 2 3 4 5 6
w2. SW5 -1 to 5 : Function Switch
Due to continuing improvement, above specification may be subject to change without notice.
PUZ-HA-8
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
9
REFRIGERANT SYSTEM DIAGRAM
5. REFRIGERANT SYSTEM DIAGRAMS
PUZ-HA30NHA4
PUZ-HA36NHA4
PUZ-A30/36NHA4
PUZ-A30/36NHA4-BS
Heat exchanger
Refrigerant
GAS pipe
connection
:15.88(5/8)
Strainer
#50
Muffler
Thermistor TH3
(Outdoor pipe)
High pressure
switch 63H
Distributor
Low pressure
switch 63L
Thermistor
TH32
(Outdoor pipe)
Strainer
#100
Strainer
#100
Refrigerant
LIQUID pipe
connection
:9.52
Strainer
(3/8)
#100
Stop valve
(with service port)
Thermistor TH7
(Outdoor)
Charge plug
(High pressure)
Charge plug
(Low pressure)
Linear
expansion valve B
Unit: mm<inch>
Thermistor
TH6
(Outdoor
2-phase pipe)
Solenoid valve
(Four-way valve)
Ball valve
unit : mm (inch)
Thermistor TH33
(Outdoor pipe)
Strainer
#100
Thermistor TH4
(Discharge)
Strainer
#100
Power
receiver
Linear expansion valve A
Compressor
Linear
expansion valve C
Injection port
Heat inter change circuit
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant recovering (pump down)
Perform the following procedures to recover the refrigerant when moving the indoor unit or the outdoor unit.
Turn on the power supply (circuit breaker).
+When power is supplied, make sure that “CENTRALLY CONTROLLED” is not displayed on the remote controller. If
“CENTRALLY CONTROLLED” is displayed, the refrigerant recovering (pump down) cannot be completed normally.
After the liquid stop valve is closed, set the SWP switch on the control board of the outdoor unit to ON. The compressor
(outdoor unit) and ventilators (indoor and outdoor units) start operating and refrigerant collecting operation begins. LED1
and LED2 on the control board of the outdoor unit are lit.
+Set the SWP switch (push-button type) to ON in order to perform refrigerant recovering operation only when the unit
is stopped. However, refrigerant recovering operation cannot be performed until compressor stops even if the unit is
stopped. Wait 3 minutes until compressor stops and set the SWP switch to ON again.
Because the unit automatically stops in about 2 to 3 minutes after the refrigerant collecting operation (LED1 is not lit and
LED2 is lit), be sure to quickly close the gas stop valve.
+In case the outdoor unit is stopped when LED1 is lit and LED2 is not lit, open the liquid stop valve completely, and then
repeat step 3 minutes later.
+If the refrigerant collecting operation has been completed normally (LED1 is not lit and LED2 is lit), the unit will remain
stopped until the power supply is turned off.
Turn off the power supply (circuit breaker).
Due to continuing improvement, above specification may be subject to change without notice.
16
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-9
6. SOUND PRESSURE LEVELS
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002
bar)
PUZ-HA30NHA2
PUZ-HA36NHA2
MODE SPL(dB)
COOLING
52
HEATING
53
LINE
90
80
MICROPHONE
70
3.3 ft
NC-70
UNIT
60
NC-60
50
NC-50
5 ft
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
GROUND
NC-20
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
Due to continuing improvement, above specification may be subject to change without notice.
PUZ-HA-10
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
: *1.Rating conditions
(cooling)-Indoor : D.B.
26.7°C(80°F), W.B. 19.4°C(67°F)
7.NOTES
STANDARD
OPERATION
RANGE
*2.Conditions
*3.Conditions
(heating)-Indoor : D.B. 21.1°C(70°F), W.B. 15.6°C(60°F)
(heating)-Indoor : D.B. 21.1°C(70°F), W.B. 15.6°C(60°F)
(heating)-Indoor : D.B. 21.1°C(70°F), W.B. 15.6°C(60°F)
Outdoor : D.B. 35°C(95°F), W.B. 23.9°C(75°F)
Outdoor : D.B. 8.3°C(47°F), W.B. 6.1°C(43°F)
Outdoor : D.B. -8.3°C(17°F), W.B. -9.4°C(15°F)
Outdoor : D.B. -15°C(5°F), W.B. -15°C(5°F)
Operating range
Indoor intake air temperature
Outdoor intake air temperature
D.B. 32°C(90°F), W.B. 23°C(73°F)
D.B. 46°C(115°F)
Maximum
D.B. 19°C(66°F), W.B. 15°C(59°F)
D.B. -18°C(0°F)*
Minimum
D.B. 28°C(83°F)
D.B. 21.1°C(70°F), W.B. 15°C(59°F)
Maximum
Heating
D.B. 17°C(63°F)
D.B. -25°C(-13°F), W.B. -25°C(-13°F)
Minimum
* In case that the wind baffle is installed. (In case that the wind baffle is not installed, the minimum temperature will be -5°C(23°F)DB.)
Cooling
Due to continuing improvement, above specification may be subject to change without notice.
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
PUZ-HA-11
8. ACCESSORIES
Part Number
Descriptions
PAC-SK52ST
Service Tool with display screen for operation and diagnostic
data
CWMB1
4 piece (1-pair) condensing unit wall mounting brackets painted steel
PAC-SF82MA-E
M-NET control adapter for Building Management System
PAC-SG59SG-E
Air Outlet Guide
(Directs airflow upward from outdoor fan)
PAC-SG64DP-E
Outdoor Drain Pan
Applicable model
All models
All models (requires 2)
All models
ULTRILITE2
Outdoor Unit Mounting Pad 24" x 42" x 3"
WB-PA2
Wind Baffle
All models (requires 2)
Due to continuing improvement, above specification may be subject to change without notice.
PUZ-HA-12
2013 P-Series - PUZ-HA Hyper Heat Outdoor Units (June 2013)
© 2013 Mitsubishi Electric US, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement