Clarion | VRX633R | Owner`s manual | Clarion VRX633R Owner`s manual

VRX633R
English
Installation and Wire connection manual
1.
BEFORE STARTING ................................................................ 47
PACKAGE CONTENTS ............................................................ 47
GENERAL CAUTIONS ............................................................. 48
CAUTIONS ON INSTALLATION .............................................. 48
INSTALLING THE MAIN UNIT ................................................. 49
REMOVING THE MAIN UNIT .................................................. 51
CAUTIONS ON WIRING .......................................................... 51
WIRE CONNECTION ............................................................... 52
SAMPLE SYSTEMS ................................................................ 54
BEFORE STARTING
1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “ ” terminal before starting. This is to prevent short
circuits during installation. (Figure 1)
2.
PACKAGE CONTENTS
1 Main unit
2 Manuals
Owner’s manual & Installation manual
Warranty card
3 Power supply lead
4 Bag for accessories of the main unit (No. 1)
Flat head screw (M5 × 8)............................4
Sems hexagonal bolt (M5 × 8)....................5
5 Bag for accessories of the main unit (No. 2)
Hook plate..................................................2
6
7
8
9
0
Cord clamp
Spacer
Special screw
Universal mounting bracket
Remote control unit
Battery
(for remote control unit)
Outer Escutcheon
DCP Case
VRX633R
47
Installation and Wire
connection manual
■ Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
3.
GENERAL CAUTIONS
English
1. Do not open the case. There are no user serviceable parts inside. If you drop anything into
the unit during installation, consult your
dealer or an authorized CLARION service
centre.
Installation and Wire
connection manual
4.
2. Use a soft, dry cloth to clean the case. Never
use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or
warm water to a soft cloth and wipe off the
dirt gently.
CAUTIONS ON INSTALLATION
1. Prepare all articles necessary for installing
the main unit before starting.
2. This model is used with the LCD panel slid
forwards (shell loading system). On some
types of cars, the LCD panel may touch the
dashboard or shift lever, in which case it cannot be installed. Check that the set will not
hamper operation of the shift lever before
choosing the place of installation.(Figure 2)
5. Use the enclosed screws for installation. Using other screws can cause damage.
(Figure 4)
6. The source unit has mounting screw holes
for NISSAN (N marks) and TOYOTA (T marks)
vehicles.
T
N
T
3. Install the unit within 30° of the horizontal
plane. (Figure 3)
N
4. If you have to do any work on the car body,
such as drilling holes, consult your car dealer
beforehand.
48
VRX633R
T
N
5.
INSTALLING THE MAIN UNIT
■ Universal Mount
English
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracket inward, then secure the stopper as
shown in Figure 6.
2. Wire as shown in Section 8.
3. Insert the main unit into the universal mounting bracket until it locks.
4. Mount the outer escutcheon so that all the
hooks are locked.
7-3/16" (182 mm)
Hole
2-1/16" (53 mm)
• Console opening dimensions
Rear fastening hole (of vehicle)
Instrument panel
Hole
Stoppers
Special Screw
Screwdriver
Rubber cap
Main unit
Universal mounting bracket
Stoppers
2-Spring
Outer escutcheon
Note: Set the outer escutcheon so that its metallic
part on the back side
fits the upper edge of
the main unit.
VRX633R
49
Installation and Wire
connection manual
Notes:
1) Some car models require special mounting kits
for proper installation. Consult your Clarion
dealer for details.
2) Fasten the front stopper securely to prevent
the main unit from coming loose.
■ Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
English
Installation and Wire
connection manual
This unit is designed for fixed installation in the
dashboard.
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (∗). (Figure 8)
If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install
the main unit in the following procedure.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the
direction of arrow to remove it. Repeat the
same for the other side to remove the springs
from the both sides. (Figure 7)
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped
for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models.
3. Wire as shown in Section 8.
4. Secure the unit in the dashboard, and then
reassemble the dashboard and the centre
panel.
The screws with this mark are enclosed in
this set.
The parts and screws with this mark
are used to install radio or included in
the installation kit.
Note 1: In some cases, the centre panel may require some modification (trimming, filling,
etc.).
50
VRX633R
Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a
nipper or a similar tool.
6.
REMOVING THE MAIN UNIT
2. Remove the outer escutcheon.
the spring into hole A of the hook plate, then
pull the main unit out by the hook plate. (Insert both the right and left edges of the hook
plate.) (Figure 9)
3. Insert the hook plate between the spring and
the universal mounting bracket, fit tab B of
CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the
wires.
Keep them well away from the engine, and
exhaust pipe, etc. Heat may damage the
wires.
3. If the fuse should blow, check to see if the
wiring is correct.
If it is, replace the fuse with a new one with
the same amperage rating as the original.
4. When any fuse is to be replaced, pull out the
fuse (15A) at the rear of the main unit and
put in a new one (Fig.10).
Figure 10
CAUTION
After the connection, fix the lead by a clamp
or insulation tape for protection.
VRX633R
51
Installation and Wire
connection manual
7.
Note: Keep the hook plate. You cannot remove the
main unit without disengaging the hook plate.
English
1. When the rear of the main unit has been secured with the method shown in Figure 6
unfasten the special screw.
8.
WIRE CONNECTION
Rear view of the Main unit
Red
∗5
1
Front right
English
Gray
2
White
Gray
∗5
!
Front left
0
3
Red
∗4
Rear right
Installation and Wire
connection manual
4
Brack
White
Brack
Rear left
B-2
B-3
B-4
B-1
6
B-5
B-6
9
5
B-7
B-8
A-7
∗1
A-8
∗3
7
A-4
A-6
A-5
@
∗2
∗2
8
No.
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
A-4
A-5
A-6
A-7
A-8
Description
REAR RIGHTB
REAR RIGHTv
FRONT RIGHTB
FRONT RIGHTv
FRONT LEFTB
FRONT LEFTv
REAR LEFTB
REAR LEFTv
+12 V MAIN POWER (∗2)
AUTO ANTENNA (∗1)
ILLUMINATION
+12 V ACCESSORY (∗2)
GROUND
No.
1
2
3
4
5
6
7
8
9
0
!
@
Description
NAVI/CCD terminal
RGB INPUT
VIDEO INPUT (for TV tuner)
Radio antenna jack (∗4)
CeNET terminal
Fuse (15A)
Phone mute (Brown)
Spare terminal (Yellow)
ISO CONNECTOR
AUDIO 4CH. OUTPUT
DVD/etc. INPUT
(for DVD changer and etc.)
Parking brake (Bright Green)
∗1:When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the
<<Remote>> output. Disconnect the <<blue/white>> wire and insulate the front ends of this lead.
A breakdown may occur if the lead is not disconnected, or front ends are not insulated.
∗2:In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory
<<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory.
∗3:Connecting the PHONE MUTE Terminal
The lead included with the unit must be connected to the specified position of the vehicle’s ISO
connector in order to use the “triggered audio mute for cellular telephones” function.
∗4:Use the attached extension lead when necessary.
∗5:When connecting CCD CAMERA, be sure to connect RCA as well as the 8-pin Mini-Din video jack.
Note : Before making any installation, disconnect the car battery - (negative) cable.
52
VRX633R
■ Connecting the Accessories
• Connection to the CCD camera for vehicle
When Clarion car navigation equipment is used, connect it to the system expansion terminal (CCD/
NAVI) and the RGB terminal of the main unit. For detailed information, refer to the operating instructions provided with car navigation equipment. When the NAVI is connected, the CCD camera
cannot be connected. When the Clarion NAVI is to be connected, set the INPUT to the NAVI position.
• If the specified lead of the cellular phone is connected to the phone mute
lead of the source unit, the audio mute is available when the cellular telephone is used.
For audio mute setting in cellular telephone use, see page 42.
• DAB (Digital Audio Broadcasting)
When the DAB is to be connected, use the Ce NET connector. For detailed information, refer to the
instruction manual of the DAB.
For DAB connection, The DAH913 can only be connected. The DAH9500Z cannot be connected.
• TV Tunner
When the TV TUNER is to be connected, connect the Ce NET connector and RCA PIN (yellow). For
detailed information, refer to the instruction manual of the TV TUNER.
■ Connecting the parking brake lead
Parking brake lamp
+ lead to battery
Connect the lead to parking brake lamp earth
in the meter panel.
Notes:
• Connecting the parking brake lead to lamp earth
allows you to watch TV/VTR/DVD changer when
the parking brake is engaged.
• When the parking brake lead is not connected,
the monitor will stay off.
- cord
parking
brake signal
lead
Connect these three leads.
Parking brake lead
(bright green)
Parking brake
VRX633R
53
Installation and Wire
connection manual
• Connection to car navigation equipment
English
The CCD CAMERA for vehicle can be connected to the system expansion terminal on the main
unit. For detailed information, refer to the instruction sheet or manual for the CCD CAMERA.
Notes:
• A power supply box (sold separately) is required for connection of the main unit and the CCD CAMERA.
• While the CCD CAMERA is used, the navigation cannot be turned on.
• The power supply box for camera CCA-147 cannot be used. Please use The CCA-188 instead.
9. SAMPLE SYSTEMS
■ Sample System 1
English
Main Unit
(VRX633R)
Amp remote
RCA PIN cable
(Sold separately)
Front
Speakers
Installation and Wire
connection manual
Amp.
Rear
Speakers
DVD/etc. INPUT
VIDEO INPUT
RCA video cable
(included the VCZ628)
Mini DIN(8P) Cable
(included the
NAX9500E)
CeNET cable
(included the TV tuner)
RCA video cable
(included the TV tuner)
RGB cable
(included the
NAX9500E)
TV Tuner
Navigation System
(NAX9500E)
∗To enable the correct input, it is necessary
to configure the VRX633R as described on
page 39.
(TTX7502z/
TTX7503z)
CeNET Cable
(included the DAB tuner)
RDI OUT
DAB Tuner
(DAH913/DAH923)
CeNET Cable
(included the Changer)
CeNET Y-adapter
(CCA-519-601,
sold separately)
Ferrite clamp
(Included the DVD changer)
DVD Changer
(VCZ628)
CD Changer
(CDC655z/655Tz/1255z/
DCZ628)
∗When two CD changers or
MD changers are connected,
CCA-519-601 is required.
54
VRX633R
Set the [CeNET/STAND ALONE]
switch to the [CeNET] position.
CeNET
STAND
ALONE
■ Sample System 2
Main Unit
(VRX633R)
Amp remote
Front
Speakers
Amp.
VIDEO INPUT
RCA video cable
(included the VCZ628)
Mini DIN(8P) Cable
(included the
NAX9500E)
CeNET cable
(included the
TV tuner)
RCA video cable
(included
the TV tuner)
Rear
Monitor
RGB cable
(included the
NAX9500E)
Navigation System
(NAX9500E)
∗To enable the correct input, it is
necessary to configure the VRX633R
as described on page 39.
∗The rear monitor displays TV/VTR
images only. Images from the DVD
changer cannot be displayed.
TV Tuner
RCA video cable (sold separately)
(TTX7502z/
TTX7503z)
AV Adapter cable
(CCA-389, sold separately)
CeNET Cable
(included the DAB tuner)
RDI OUT
DAB Tuner
(DAH913/
DAH923)
VTR
CeNET Cable
(included the Changer)
CeNET Y-adapter
(CCA-519-601,
sold separately)
Ferrite clamp
(Included the DVD changer)
DVD Changer
(VCZ628)
CD Changer
(CDC655z/655Tz/1255z/
DCZ628)
∗When two CD changers or
MD changers are connected,
CCA-519-601 is required.
Set the [CeNET/STAND ALONE]
switch to the [CeNET] position.
CeNET
STAND
ALONE
VRX633R
55
Installation and Wire
connection manual
Rear
Speakers
DVD/etc. INPUT
English
RCA PIN cable
(Sold separately)
■ Sample System 3
Main Unit
(VRX633R)
Amp remote
English
RCA PIN cable
(Sold separately)
Front
Speakers
Amp.
Installation and Wire
connection manual
Rear
Speakers
VIDEO INPUT
DVD/etc. INPUT
CeNET cable
(included the TV tuner)
RCA video cable
(included the TV tuner)
Mini DIN(8P) Cable
(included the
CCD camera)
TV Tuner
(TTX7502z/
TTX7503z)
CCD camera
RCA video cable
(included the CCD camera)
∗To enable the correct input,
it is necessary to configure
the VRX633R as described
on page 39.
CeNET Cable
(included the DAB tuner)
RDI OUT
CD Changer
(CDC655z/655Tz/1255z/
DCZ628)
56
VRX633R
DAB Tuner
(DAH913/DAH923)
CeNET Cable
(included the Changer)
Download PDF