Connevans

This product may be purchased from Connevans Limited secure online store at www.DeafEquipment.co.uk

DeafEquipment.co.uk

Solutions to improve the quality of life

VIBRATION WATCH equipped with:

Vibration Alarm won't disturb others.

Beep Alarm option

Auto Reload Countdown Timer can be set for seconds, minutes & hours. Use for reminders such as medical conditions, medication, timing presentations or procedures, parking, cooking. Will automatically reload to preset countdown time.

Electo-Luminescent backlight

For viewing display at night

Second Clock great when traveling in a different time zone.

Two Alarm Settings use for daily reminders, wake up, snooze, medication

Hourly Alert/Chime Option

12 or 24 Hour clock

Stopwatch

BEFORE YOU BEGIN

Press the MODE, START/STOP,

LAP/RESET buttons at the same time and hold until display clears.

Release buttons. The clock time will be at 12:00 A.M. with the

Alarms, Hourly Alert, Beeping and Vibration functions not set.

The date will be January 1 and the

OPERATING MODES

Your watch has six operating modes:

To go from one operating mode to another, repeat pressing the

MODE button for each mode to be displayed. The operating modes will rotate in the order as listed above.

TO BECOME FAMILIAR WITH

THE OPERATING MODES &

THEIR SYMBOLS, ROTATE

THROUGH EACH MODE BY

PRESSING THE ‘MODE”

BUTTON.

FIRST TIME SETTING OF

YOUR CALENDAR/CLOCK

(You must have this set for your

Alarm Settings to be accurate.)

When setting the Calendar &

Clock, the rotation for setting is

Seconds, Hour, Minutes, 12/24Hr,

Date, Month, Day of Week.

ONLY when the digits are

BLINKING can you set or change the setting. The clock will stop blinking when no button is pressed for two minutes. You cannot switch to another mode of operation while the display is blinking. To exit and stop the blinking, push LAP/RESET button.

1. Repeat pressing the MODE button until the (1) CALENDAR

CLOCK operating mode shows on the display.

2. Press & Hold the LAP/RESET button until the second’s digits begin to BLINK.

Press the START/STOP button to

3. Press the MODE button. The hour digits will begin to BLINK.

Press the START/STOP button to rotate to correct hour of the day.

WHEN IN THE 12 HR MODE, A

PM INDICATOR WILL APPEAR

ON THE DISPLAY ABOVE

AND LEFT OF THE HOUR

DIGITS. AS YOU ROTATE TO

12 HOURS THE PM MUST

SHOW FOR SETTING

CORRECT TIME FOR

AFTERNOON OR EVENING.

BE SURE TO SET CORRECTLY

FOR THE CURRENT TIME OF

DAY.

4. Press the MODE button to go to the minute digits. The minute digits will begin to BLINK.

Press the START/STOP button to rotate to the correct minute.

5. Press the MODE button and the and BLINK on the display. To select the 24 Hour Mode, press the will show on display.

6. Press the MODE button for the at the top left corner of the display. Press the START/STOP button to rotate to the correct date of the month. (1 - 31)

7. Press the MODE button for the the display. Press the

START/STOP button to rotate to the current month of the year.

September)

8. Press the MODE button for the on the display. Press the

START/STOP button to rotate to shows. Hourly alert is off when icon doesn’t show.

9. Press the LAP/RESET button when you have finished the correct set up. The display will stop blinking.

HOW TO SET AN ALARM

CLOCK (Setting procedure is the same for BOTH alarms)

1.Repeat Pressing the MODE button to rotate to the alarm

ALARM.

2.Press & Hold the LAP/RESET button until the hour digits

BLINK.

Press the START/STOP button to rotate to the hour wanted. for correct setting.

3.Press the MODE button to go to the minutes. The minutes will

BLINK. Press the START/STOP button to rotate to the minute wanted.

4.Press the LAP/RESET Button when finished. The display will stop blinking. The set icon will show on the display. Your alarm is set.

When A1 Alarm is set the icon shows on the display beside the

ON/OFF SETTINGS OF

ALARMS

Note: To turn on or off First mode.

To turn on or off Second Alarm

Repeat Pressing the MODE button to show alarm you wish to turn off or on: 1ST OR 2ND

ALARM.

Repeat Pressing the START

/STOP button to rotate, alarm on

(hourly alert) & alarm off. When

Icon(s) shows, alarm is set. Alarm is off when icon does not show.

(See previous illustration)

HOW TO ACTIVATE OR

DEACTIVATE VIBRATION

AND BEEP FUNCTION

1. Repeat Pressing the MODE button to the CALENDAR

CLOCK mode.

2. Repeat Pressing the

START/STOP button to rotate through the selection of settings.

When a function is activated, its respective icon will be highlighted, at the top right corner of the display. Rotation will be:

Vibration ON, Beep ON,

Vibration and Beep ON, Vibration

& Beep OFF. Select one of the four functions that you desire.

This can be changed at anytime by following steps 1 and 2.

HOW TO TURN ON AND OFF

THE HOURLY ALERT

1. Repeat Pressing the MODE button and select either 1st

ALARM=A1 or 2

ND

ALARM=A2

2. Repeat Pressing START/STOP button until the Hourly Alert indicator (located beside the Al 2 indicator) shows on the display.

Hourly alert is on when icon

Alarm will stop automatically after approximately 20 seconds.

To stop alarm before the

automatic stop, press any button.

NOTE: To check setting the watch is in at any time, press the MODE button. With each press of the button the vibration and/or beep will respond if set.

HOW TO USE THE

COUNTDOWN TIMER

1. Repeat Pressing the MODE

(COUNTDOWN TIMER) operating mode.

2. Press & Hold the LAP/RESET

Button until the Seconds digits

BLINK. Press the START/STOP button to set to the seconds wanted. You can select from 0 to

59 seconds. If you do not wish to set the seconds, go to #3 below.

3. Press the MODE Button to go to the hours. The hour digits will

BLINK. Press the START/STOP button to set the number of hours

4. Press the MODE Button to go to the minutes. The minute digits will BLINK. Press the

START/STOP button to set the number of minutes wanted. You

5. Press LAP/RESET button when you have finished. The display will stop blinking.

To reset the Countdown Timer for a different time see "How to

Use the Countdown Timer" and follow instructions.

TO START THE

COUNTDOWN TIMER,

Press the START/STOP button

(after the countdown timer is set).

The timer will start to countdown.

To interrupt, press the

START/STOP button. Pressing the START/STOP button again will start the countdown from where it last left off.

Note: When Countdown Timer is set for more than ten minutes, a short single reminder will advise you of 10 minutes remaining and then at 5 minutes remaining.

AUTO RELOAD

COUNTDOWN TIMER will automatically reload for the time

If you do not wish to start the countdown again immediately, press the START/ STOP button twice, if alarm is activated. Press once to stop the countdown if alarm is not activated.

To restart the preset countdown at any time, press the START/STOP button while in the

TO USE THE REPEATABLE

COUNTDOWN TIMER WITH

PAUSES INBETWEEN

When the auto-repeat countdown timer reaches zero it automatically alarms and starts to countdown again for the preset time. You can cancel the countdown and return to the original countdown time.

To reset to the original countdown time PUSH the LAP/RESET button and HOLD IT for approximately 2 to 3 seconds.

Digits will flash showing the amount of time that the countdown was set for originally.

Push the LAP/RESET button once, and the digits will stop flashing. (If you do not push the

LAP/RESET button to stop the flashing, the digits will stop flashing automatically after 2 minutes.)

To activate the start of the countdown when you need it, push the START/STOP button once.

HOW TO USE THE

STOPWATCH

1. Repeat Pressing the MODE button to show STOPWATCH on the display.

2. To start the Stopwatch, press the START/STOP button. The

Stopwatch will start keeping time and the Icon (symbol at the top of the display) will flicker to show the action.

TO STOP THE STOPWATCH, press the START/STOP button.

Pressing the START/STOP button again will start the stopwatch running from where it last left off. seconds. Each hour accumulated shows at the top left of the display.

To RESET the stopwatch to zeros, press the LAP/RESET button, when it is in a stop position.

Split Timing on Stopwatch

1. Start the Stopwatch by pressing the START/STOP button. The stopwatch will start keeping time.

2. Press the LAP/RESET button.

The watch will continue counting the time even though you do not see it on the display. The Icon at the top of the display will continue to flicker to show action and that counting continues.

3. Press the LAP/RESET button again and the display will change and show the time that has accumulated in total.

4. To RESET the Stopwatch, press the START/STOP button and then press the LAP/RESET button.

HOW TO SET THE SECOND

CLOCK

1. Repeat Pressing the MODE button to show SECOND

CLOCK (T2)

2. Press & Hold the LAP/RESET button until the Hours digits

BLINK.

3. Press the START/STOP button to rotate to the hour you wish to indicator for correct setting of afternoon or evening.)

4. Press the LAP/RESET button when desired hour has been set.

NOTE: Only the hour can be set in second clock mode. (The minutes and seconds will be the same as the Calendar Clock)

HOW TO USE THE EL BACK

LIGHT

Press the LIGHT button to light up the LCD display at any time. The screen will be lit for approximately 3 seconds before going off automatically.

The EL back light will flash when an alarm is activated

BATTERY INFORMATION

Your watch uses a Standard 3 volt lithium CR2032 or equivalent battery. Battery life will vary due to how often the EL back light and vibration function are used.

Batteries should be replaced by a qualified person to maintain water resistance.

DISCLAIMER

GLOBAL does not accept any responsibility what so ever for any inconvenience or noncompliance for medication or any other reminder the watch may be used for.

SERVICE

This unit should be serviced by qualified service personnel. The user should not attempt to service the unit.

Servicing should be referred to:

Global Assistive Devices, Inc.

4950 North Dixie Highway,

Fort Lauderdale FL USA 33334

Before sending your unit for service, have the battery checked and/or try resetting by pressing the

MODE, START/STOP and

LAP/RESET buttons at the same time and hold until the display clears.

ONE YEAR LIMITED

WARRANTY

Your VibraLITE 3 is warranted to be free from defects in material or workmanship for One Year from the date of purchase.

This is a limited warranty and covers watch functions only. This warranty does not apply to the battery, band or to any unit which has been subject to misuse, negligence or accident. This warranty is void if the watch has been tampered with, altered, or repaired other than by a qualified service center. At its option,

GLOBAL ASSISTIVE

DEVICES, INC. may select to replace the unit, rather than repair it. During the warranty period, return the watch, with dated proof of purchase, in a secure package, insured and with shipping charges prepaid. No C.O.D. packages will be accepted. Please include a note describing the service required and include $8.50 (check, money order, Visa, MasterCard,

American Express, or Discover) for shipping and handling in the

USA. Other Countries please contact us for pricing.

Copyright:

GLOBAL

ASSISTIVE DEVICES, INC .

4950 North Dixie Highway

Fort Lauderdale Florida USA

33334-3947

QUICK REFERENCE

Model VL300

SELECTION OF VIBRATION, BEEP, BOTH OR OFF SIGNAL (S)

Press MODE button until the CALENDAR CLOCK mode shows on the display. Repeat pressing

START/STOP button to select desired function. Icon(s) at top right of display will indicate function:

Vibration, Beep, Both or Off.

A Quick Check to see what function is set, is to push the MODE button while in the Calendar Clock mode. The function that is set will respond each time you push the MODE button.

SETTING OF ALARMS AND COUNTDOWN TIMER

Press MODE button to rotate to the mode you wish to set. (TR for COUNTDOWN TIMER; A1 or A2 for ALARMS) Press and Hold LAP/RESET button until the digits blink. While digits blink, press the

START/ STOP button to advance the blinking function to the time wanted. Press the MODE button to change from hours to minutes and advance the time by pushing START/STOP button. For alarm

settings, hour(s) and /or minute(s) can be set. For countdown timer, seconds and/or hour(s) and

minute(s) can be set. Press the LAP/RESET button when completed. (Digits will stop blinking) In the

Alarm(s) mode, the alarm indicator icon shows which alarm is activated.

To reset Alarms & Countdown Timer for a different time, repeat instructions as above.

AUTO RELOAD COUNTDOWN TIMER

When the countdown timer reaches "0", it will automatically reload for the time that was preset. If you do not wish to start the countdown again immediately, press the START/ STOP button twice, if the alarm is activated. Press once to stop the countdown if the alarm is not currently activated. To restart the preset countdown at any time, press the START/STOP button while in the TR

(COUNTDOWN) mode.

HOURLY ALERT SETTING

Press the MODE button until display is in an ALARM Mode. (A1 or A2) Repeat pressing the

START/STOP button until the Hourly Chime icon shows. (Located beside the A2 icon)

Copyright:

Global

Assistive Devices, Inc.

Fort Lauderdale Florida USA