Mitsubishi | X100 | User`s manual | Mitsubishi X100 User`s manual

Configuration and Connections
Mitsubishi Installation
xi
SYSTEM 4xi
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: MITSUBISHI
Included Communications Adapter(s):
Quantity
1
1
1
Part Number
26-473-01
26-475-01
26-458-01
Description
ADP, UNV, “E”
ADP, UNV, “G”
ADP, UNV, “NEC-LCD MT”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
CONFIG
AS
✔
MODEL
1
SW1
2 3
MITSUBISHI VS
SW2 SW3 SW4 SW5 SW6 PROJ
4
CABLE
COMM
ADAPTER
VS
off on off on
0
0
8
5
0
J15
26-473-01
LVP-X100
off on off on
0
0
6
F
0
J15
26-475-01
LVP-X200X300
off on off on
0
1
6
F
0
J15
26-475-01
LVP-X400
off on off on
0
2
6
F
0
J15
26-458-01
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 1
Configuration and Connections
Mitsubishi Installation
xi to Mitsubishi LVP-X100
Connecting System 4xi
If the System 4xi is already configured for a Mitsubishi LVP-X100 projector, go
to step 4. If it is not set up correctly, it will be necessary to change switch
settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the
correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Mitsubishi LVP-X100. Apply power to the System 4xi
and do the following:
to display the MENU SELECT on the LCD screen.
a. Press
b. Press
[System 4NE model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(See note.)
(Note: Information depends on
System 4NE setup.)
c. Press
}
or
to step to Menu 8.
to select this menu.
d. Press
or
to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the
following information:
PRJ = MITS
PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi User’s Manual to remove the
System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.
Config
as
Projector
Mits. LVP-X100
SW1: 1-2-3-4 SW2
off-on-off-on
0
SW3
0
SW4 SW5
6
F
SW6 Prj Cable
0
Comm
Adapter
J15
SW3
26-475-01
SW5
SW2
J15
SW1
1
2
3
SW4
4
ON
3. Double-check your work and be sure the System 4xi cover is on securely.
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
5. The Mitsubishi LVP-X100 Comm Adapter (26-475-01) has a 9-pin male
connector that accommodates the Comm Extension cable. The other end of the
Comm Adapter plugs into the projector’s RS-232C port.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 2
Configuration and Connections
Mitsubishi Installation
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
into the PJ Comm port on the System 4xi.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output. Connect the 15-pin connector on the other end
of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X100
connector panel.
System 4xi Series – Mitsubishi LVP-X100 Projector Connections
Use the illustration below as a guide when connecting the System 4xi to a
Mitsubishi LVP-X100 Projector. Refer to Mitsubishi LVP-X100 documentation to
continue the installation.
15-Pin Male
ComAdapter
26-475-01 "G"
G
SY-VGA
26-173-01
9-Pin Female
RGBHV 5 BNC
15-Pin
Male
INPUT 1
H/HV
R/C
INPUT 2
V
G/Y
AUDIO
B
H/HV
R/C
INPUT 3
V
G/Y
AUDIO
B
H/HV
R/C
INPUT 4
V
G/Y
AUDIO
B
H/HV
R/C
OUTPUT
V
G/Y
AUDIO
B
PJ COMM
RS 232
H/HV
V
R/C
AUDIO
G/Y
B
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 3
Configuration and Connections
Mitsubishi Installation
xi to Mitsubishi VS Projector
Connecting System 4xi
If the System 4xi is already configured for a Mitsubishi VS Projector, go to step
4. If it is not set up correctly, it will be necessary to change switch settings on the
System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct
configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Mitsubishi VS projector. Apply power to the System 4xi
and do the following:
to display the MENU SELECT on the LCD screen.
a. Press
b. Press
[System 4NE model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(See note.)
(Note: Information depends on
System 4NE setup.)
c. Press
or
to step to Menu 8.
to select this menu.
}
d. Press
or
to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the
following information:
PRJ = MITS
PRJ BAUD = n/a
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi User’s Manual to remove the
System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.
Config
as
✔
Monitor
SW1: 1-2-3-4 SW2
Mitsubishi VS
off-on-off-on
0
SW3 SW4 SW5
0
8
5
SW6 Prj Cable
0
J15
SW3
Comm
Adapter
26-473-01
SW5
SW2
J15
SW1
1
2
3
SW4
4
ON
3. Double-check your work and be sure the System 4xi cover is on securely.
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
5. The Mitsubishi VS Comm Adapter (26-473-01) has a two 9-pin male connectors.
Plug the Comm Extension cable into the Comm Adapter. Plug the other end of
the Comm Adapter into the “Remote 1” connector of the projector.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 4
Configuration and Connections
Mitsubishi Installation
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
(shown as CC 50') into the PJ Comm port on the System 4xi. The other end
plugs into the other 9-pin male D connector on the Comm Adapter (mentioned in
Step 5).
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output and those on the other end onto the matching
BNCs on the Mitsubishi VS projector connector panel. See connection diagram
below.
xi Series – Mitsubishi VS Projector Connections
System 4xi
Use the illustration below as a guide when connecting the System 4xi to a
Mitsubishi VS projector. Refer to Mitsubishi VS documentation to continue the
installation.
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
"E"
26-473-01
"E"
__________ System 4xi channel numbers correspond to the projector’s “Group” numbers.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 5
Configuration and Connections
Mitsubishi Installation
xi to Mitsubishi LVP-X200 Projector
Connecting System 4xi
If the System 4xi is already configured for a Mitsubishi LVP-X200 projector, go
to step 4. If it is not set up correctly, it will be necessary to change switch
settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the
correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Mitsubishi LVP-X200 projector. Apply power to the
System 4xi and do the following:
to display the MENU SELECT on the LCD screen.
a. Press
b. Press
[System 4NE model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(See note.)
(Note: Information depends on
System 4NE setup.)
}
c. Press
or
to step to Menu 8.
to select this menu.
d. Press
or
to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the
following information:
PRJ = MITS
PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi User’s Manual to remove the
System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.
Config
as
Projector
Mits. LVP-X200
SW1: 1-2-3-4 SW2 SW3
off-on-off-on
0
1
SW4
6
SW5 SW6
F
0
Prj Cable
Comm
Adapter
J15
26-475-01
SW3
SW5
SW2
J15
SW1
1
2
3
SW4
4
ON
3. Double-check your work and be sure the System 4xi cover is on securely.
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following cable diagram and continue.
5. The Mitsubishi LVP-X200 Comm Adapter (26-475-01) has two 9-pin male
connectors. Plug the Comm Extension cable into the Comm Adapter. Plug the
other end of the Comm Adapter into the “RS-232C” connector of the projector.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 6
Configuration and Connections
Mitsubishi Installation
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
(shown as CC 50') into the PJ Comm port on the System 4xi.
______ Secure the screws on all D connectors.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output. Connect the 15-pin connector on the other end
of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X200
connector panel.
xi Series – Mitsubishi LVP-X200 Projector Connections
System 4xi
Use the following illustration as a guide when connecting the System 4xi to a
Mitsubishi LVP-X200 projector. Refer to Mitsubishi documentation to continue
the installation.
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
15-Pin Male
ComAdapter
26-475-01 "G"
G
SY-VGA
26-173-01
9-Pin Female
RGBHV 5 BNC
15-Pin
Male
INPUT 1
H/HV
R/C
INPUT 2
V
G/Y
AUDIO
B
H/HV
R/C
INPUT 3
V
G/Y
AUDIO
B
H/HV
R/C
INPUT 4
V
G/Y
AUDIO
B
H/HV
R/C
OUTPUT
V
G/Y
AUDIO
B
PJ COMM
RS 232
H/HV
V
R/C
AUDIO
G/Y
B
__________ System 4xi channel numbers correspond to the projector’s “Group” numbers.
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-401-02 Rev. C
Page 7
Download PDF