Catalogue Sheet: ESLTS Series

Catalogue Sheet: ESLTS Series
new product
Type:
Project/Location:
ESLTS SERIES
T-Bar 12V MR16 LED Unit
Contractor:
Prepared By:
Date:
Model No.:
TYPICAL SPECIFICATIONS
Fully recessed units for T-Bar mounting in suspended ceilings. The ESLTS
Series battery units are designed for T-Bar ceiling grid installation. This
slim-line, unobtrusive unit is ideally suited for any commercial location
where there is limited wall space and where the greater directional flexibility
of ceiling-mounted heads is needed to provide greater light distribution.
Supply and install a complete emergency lighting system as described herein
and shown on the drawings. The Emergi-Lite® Smart Diagnostic Micro
controller board shall supply the rated load for a minimum of 30 minutes
to 87.5% of the rated battery voltage. The unit shall be rated 120V or 347V,
60 Hz and be CSA listed. The unit shall have an output of
V.
FEATURES
∙∙ Rugged steel cabinet with corrosion-resistant undercoating
The charger shall be fully computer tested and its charge voltage factory
set to ± 1% tolerance. Chargers with field-adjusted potentiometers are not
acceptable. A pulse-type charger shall be employed to promote long battery
life and reduce the potential for grid corrosion. The charger shall provide a
continuous high charge to recharge the battery, when the battery is at full
capacity, the charger will shut-off. Periodically the charger shall provide a
pulse of energy to keep the battery topped off. The charger shall be current
limited, temperature compensated, short-circuit proof and reverse polarity
protected. The unit shall be furnished with an electronic lockout circuit,
which will connect the battery when the AC circuit is activated, and an
electronic brownout circuit, which will activate the emergency lights when
utility power dips below 75% of nominal voltage.
∙∙ Battery and charger are concealed above the ceiling level
in the unit cabinet
∙∙ Removable panel provides easy access to battery
and circuitry
∙∙ Test switch and LED indicators are mounted on the visible
bottom panel
∙∙ Units mount quickly and easily in standard 2’ x 2’ or 2’ x 4’
grids without any additional hardware
∙∙ Solid-state pulse-type charger – current-limited,
temperature-compensated, short-circuit proof and
reverse-polarity protected
∙∙ Unit comes standard with electronic lockout and
brownout circuits
A low voltage battery protection circuit shall be provided and will disconnect
the battery from the fused output circuit at the end of discharge. The unit
shall self-test for 1 minute every 30 days, 10 minutes on the 6th month
and 30 minutes every 12 months. The unit shall be capable of full recharge
in compliance with CSA specifications. The unit shall be furnished with
sealed dust tight relay, a test switch and seven diagnostic LED indicator
lights to continuously monitor the status of the unit: Battery Failure, Battery
Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC “ON”,
Charger High Rate. The unit shall be T-bar mounted and come complete
with tool-less emergency lighting heads requiring no tools to adjust or aim.
∙∙ Sealed dust-proof transfer relay, test switch and LED
indicator lights
∙∙ Long-life, maintenance-free Lead Acid battery
∙∙ Standard 120/347VAC input voltage
∙∙ NEXUS® compatible (for more information on NEXUS®,
please consult your sales representative)
∙∙ CSA C22.2 No. 141 certified
∙∙ Available with a selection of 4W, 5W or 6W LED lamps
Equipment is Emergi-Lite® model:
∙∙ Vandal resistance clear polycarbonate lens
∙∙ Optional tamper-proof screws available
REPLACEMENT LAMPS
Made in Canada
58
ORDERING CODE
LAMP TYPE
VOLTAGE/WATTAGE
580.0093-EL
MR16, LED
12V-4W
580.0104-EL
MR16, LED
12V-5W
580.0106-EL
MR16, LED
12V-6W
new product
Type:
Project/Location:
Contractor:
ESLTS SERIES
Prepared By:
Date:
T-Bar 12V MR16 LED Unit
Model No.:
DIMENSIONS
Dimensions are approximate and subject to change.
3-1/4” [8.2 cm]
10-1/2” [23.6 cm]
7-1/4” [18.3 cm]
23-3/4” [60.3 cm]
4-5/8” [11.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
12ESLTS36
12ESLTS72
120/347VAC
30MIN
1H00
1H30
2H00
0.09/0.03A
36
21
15
12
4H00
–
0.15/0.06A
72
42
30
24
12
ORDERING INFORMATION
SERIES
CAPACITY
12ESLTS= 12V 36W= 36W
72W= 72W
COLOUR
A.C.VOLTAGE
OPTIONS
Blank= factory Blank= 1
20/347VAC input U= Auto-Diagnostic, audible
white
UN= Auto-Diagnostic, non-audible
NEX= NEXUS® wired system interface*
NEXRF= N
EXUS® wireless
sysetm interface*
CT= Cabtire
LW= Twist Lock Plug
D= Time Delay (programmable)
T= Lamp Disconnect
P= Light Activated Test Switch
TBAC= AC Terminal Block
TBACDC= AC/DC Terminal Block
TB= DC Terminal Block
X2= Remote Test Receiver**
TP= Tamper-Proof Screws***
* Not all options available with NEXUS® System.
Please consult your sales representative.
**TX2= remote test transmitter (sold separately)
***990.0119-E= tamper proof bit (sold separately)
EXAMPLE: 12ESLTS36WU/2LG
59
# OF HEADS
LAMP WATTAGE
/2= two heads
/3= three heads
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement