Bobrick 818615 Heavy-Duty Surface-Mounted Soap Dispenser Technical Data Sheet

Technical Data

ConturaSeries

®

SURFACE-MOUNTED

SOAP DISPENSER FOR

ANTIBACTERIAL SOAPS

(with special container made from type-316 stainless steel)

818615

S

7''

180mm

S

S

1/8''

3mm

Typ.

Finish Face of Wall

Lid for Top Filling

S

Concealed

Wall Plate

6-1/8''

155mm

S

Window

Push Button Valve

2-9/16''

65mm

3-5/16''

85mm

MATERIALS:

Container — Body is 18-8 , type-316, 20-gauge (0.9mm) stainless steel with satin finish. Drawn, one-piece, seamless construction. Front has same degree of arc as other Bobrick ConturaSeries washroom accessories. Radius on corners and edges complement other ConturaSeries accessories. Back plate is 22-gauge (0.8mm) stainless steel with 20-gauge (0.9mm) stainless steel mounting bracket attached. Container body and back plate are epoxy-sealed to prevent warping and leakage.

Concealed wall plate is 20-gauge (0.9mm) stainless steel. Equipped with a plastic soap refill-indicator window and a locked, hinged stainless steel lid for top filling. Capacity: 40-fl oz (1.2-L).

Valve — Black molded plastic push button. Soap head-holding mushroom valve. Stainless steel spring. U-packing seal and duckbill. Antibacterial-soap-resistant plastic cylinder.

OPERATION:

Corrosion-resistant valve dispenses commercially marketed all-purpose hand soaps. Valve operates with one hand, without tight grasping, pinching, or twisting of the wrist, and with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Window indicates when refill is required. The locked, hinged lid opens for top filling with special key provided. Concealed, vandal-resistant mounting.

INSTALLATION:

Secure wall plate to the wall with screws furnished at points indicated by an S. Slide mounting bracket of container down onto wall plate and secure unit with furnished locking-screw. For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with screws furnished. For other wall surfaces, provide fiber plugs or expansion shields for use with screws furnished, or provide 1/8'' (3mm) toggle bolts or expansion bolts.

Note: Surface-mount the dispenser plumb and true with valve 6'' (152mm) to right or left of lavatory center. Provide 4''

(102mm) minimum clearance from the lid to the underside of any horizontal projection. Push buttons should be located 44"

(1120mm) maximum above the finish floor.

SPECIFICATION:

Surface-mounted soap dispenser shall be type-316 stainless steel with satin finish. Corrosion-resistant valve shall dispense commercially marketed all-purpose hand soaps. Valve shall be operable with one hand and with less than 5 pounds of force

(22.2 N) to comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Front of soap dispenser shall have same degree of arc and match other Bobrick ConturaSeries accessories in the washroom. Radius on corners and edges of soap dispenser shall complement other Bobrick ConturaSeries washroom accessories. Container body and back plate shall be epoxy-sealed to prevent warping and leakage. Soap dispenser shall have concealed, vandal-resistant mounting. Locked, hinged stainless steel lid for top filling shall require special key to open. Capacity shall be 40-fl oz (1.2-L).

Surface-Mounted Stainless Steel Soap Dispenser For Antibacterial Soaps shall be Model 818615 of Bobrick

Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick

Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and

Bobrick Washroom Equipment Limited, United Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.

Rev. 3/10/10 Printed in U.S.A.

© 2010 by Bobrick Washroom Equipment, Inc.