Daikin | Quaternity H-Series | Specifications | Daikin Quaternity H-Series Specifications

Daikin Quaternity H-Series Specifications
EDUS04-906_b
- Heat Pump H-Series
EDUS04-906_b
Split-System
Room Air Conditioners
H-Series
Quaternity
1.
2.
3.
4.
5.
6.
7.
Heat Pump
FTXG09HVJU
FTXG12HVJU
FTXG15HVJU
RXG09HVJU
RXG12HVJU
RXG15HVJU
Power Supply ..............................................................................................2
Functions.....................................................................................................3
Specifications ..............................................................................................4
Dimensions .................................................................................................6
Wiring Diagrams..........................................................................................7
Piping Diagrams..........................................................................................8
Capacity Tables ..........................................................................................9
7.1 Heat Pump ................................................................................................... 9
8. Operation Limit..........................................................................................15
9. Sound Level ..............................................................................................16
9.1 Measuring Location .................................................................................... 16
9.2 Octave Band Level ..................................................................................... 17
10.Electric Characteristics..............................................................................19
11.Installation Manual .................................................................................... 20
11.1 Indoor Units ................................................................................................ 20
11.2 Outdoor Units ............................................................................................. 33
12.Operation Manual......................................................................................40
13.Optional Accessories ................................................................................71
13.1 Option List .................................................................................................. 71
13.2 Installation Manual ..................................................................................... 72
Room Air Conditioners H-Series
1
Power Supply
EDUS04-906_b
1. Power Supply
Quaternity
Indoor Units
Outdoor Units
FTXG09HVJU
RXG09HVJU
FTXG12HVJU
RXG12HVJU
FTXG15HVJU
RXG15HVJU
Power Supply
1φ, 208-230V, 60Hz
Note:
Power Supply Intake ; Outdoor Unit
2
Room Air Conditioners H-Series
EDUS04-906_b
Functions
Basic
Function
Functions
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°FDB)
Operation Limit for Heating (°FWB)
Compressor
Comfortable
Airflow
Comfort
Control
Operation
PAM Control
Energy Saving During Operation Standby
Oval Scroll Compressor
Swing Compressor
Rotary Compressor
Reluctance DC Motor
Power-Airflow Flap
Power-Airflow Dual Flaps
Wide-Angle Louvers
Vertical Auto-Swing (Up and Down)
Horizontal Auto-Swing (Right and Left)
3-D Airflow
Comfort Airflow Mode
COOLING BREEZE Operation
Auto Fan Speed
Indoor Unit Quiet Operation
Night Quiet Mode (Automatic)
Outdoor Unit Quiet Operation (Manual)
INTELLIGENT EYE
2-Area INTELLIGENT EYE
Quick Warming Function
Hot-Start Function

Automatic Defrosting
Automatic Operation
Humidifying Operation
Drying Operation
DRY COOLING Operation


—


Programme Dry Function
Lifestyle
Convenience

14~
109
–4~
75

—
—

—

—









—
—
—
—

Fan Only
Air-Purifying Operation
New POWERFUL Operation (Non-Inverter)
Inverter POWERFUL Operation
Dry Keep
Priority-Room Setting
Cooling / Heating Mode Lock
HOME LEAVE Operation
ECONO Mode
Indoor Unit ON/OFF Switch
Signal Reception Indicator
Multi-colored Indicator
Monitor Brightness Setting
Temperature & Humidity Level Information
Display (Remote Controller)
Childproof Lock
R/C with Back Light
Category
Health &
Clean
Timer
Worry Free
“Reliability &
Durability”
Flexibility
—
—

—
1
2
JP set
—
—
—
—




Remote
Control
Remote
Controller
Functions
FTXG09/12/15HVJU
RXG09/12/15HVJU
Category
FTXG09/12/15HVJU
RXG09/12/15HVJU
2. Functions
Air-Purifying Filter
—
Photocatalytic Deodorizing Filter
—
Air-Purifying Filter
with Photocatalytic Deodorizing Function
Titanium Apatite Photocatalytic
Air-Purifying Filter
Deodorizing Filter for Streamer
Flash Streamer Air-Purifying
Air Filter (Prefilter)
Wipe-clean Flat Panel
Washable Upper Grille
Filter Cleaning Indicator (Remote Controller)
Mold Proof Operation
Mold Shock Operation
Mold Proof Stick
Comfort Sleep Operation
Fresh Air Supply Ventilation
Home Leave Ventilation
Weekly Timer
24-Hour ON/OFF Timer
Count Up-down ON/OFF Timer
Night Set Mode
Auto-Restart (after Power Failure)
Self-Diagnosis (Remote Controller) Display
Wiring Error Check
Anticorrosion Treatment of Outdoor Heat
Exchanger
Multi-Split / Split Compatible Indoor Unit
H/P, C/O Compatible Indoor Unit
Chargeless
Either Side Drain (Right or Left)
Power Selection
Low Temperature Cooling Operation
(5°F / -15°C)
°F/°C changeover R/C temperature display
(factory setting : °F)
5-Rooms Centralized Controller (Option)
—







—
—

2
—
—
—

OFF only



—

—
—


—
—
3

Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)

Remote Control Adaptor
(Normal Open Contact) (Option)
DIII-NET Compatible (Adaptor) (Option)
Wireless
Wired



—


—
Note:  : Included Functions
— : No Functions
(1) Inverter POWERFUL operation can be used for COOLING, DRY COOLING, and HEATING.
(2) The function setting is cancelled as it is restarted automatically.(3) Temperature display 16~99°F (–9°C~37°C)
Room Air Conditioners H-Series
3
Specifications 60Hz 230V
EDUS04-906_b
3. Specifications
60Hz 230V
Indoor Units
Models
Capacity
Rated (Min.~Max.)
Moisture Removal
Running Current (Rated)
Power Consumption Rated (Min.~Max.)
Power Factor
EER (Rated)
COP (Rated)
Energy
SEER/HSPF
Efficiency
Liquid
Piping
Gas
Connections
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge of
Refrigerant
Indoor Units
Front Panel Color
Airflow Rate
cfm (m³/min)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation Sound
H/M/L
Outdoor Units
Casing Color
Type
Compressor
Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
Fan
Airflow Rate
FTXG09HVJU
RXG09HVJU
Outdoor Units
cfm (m³/min)
Type
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Fan
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L
Sound
Drawing No.
Cooling
Heating
Cooling
Heating
Btu/h
9,000 (5,300~12,300)
12,000 (4,400~18,000)
12,000 (5,300~15,700)
16,000 (4,400~19,100)
Pt/h
A
W
%
Btu/h·W
W/W
3.3
3.10
570 (250~900)
80.0
15.8
—
—
4.04
780 (220~1,900)
84.0
—
4.51
4.1
4.30
860 (260~1,300)
87.0
14.0
—
—
5.64
1,160 (220~2,100)
89.5
—
4.04
26.1
11.0
24.2
10.6
φ 1/4” (6.4 mmm)
φ 3/8” (9.5 mm)
inch (mm)
inch (mm)
inch (mm)
feet (m)
feet (m)
feet (m)
φ 11/16” (17.5 mm)
φ 11/16” (17.5 mm)
Both Liquid and Gas Pipes
32 ft (10 m)
26 ft (8 m)
—
oz/ft
H
M
L
φ 1/4” (6.4 mmm)
φ 3/8” (9.5 mm)
Both Liquid and Gas Pipes
32 ft (10 m)
26 ft (8 m)
—
—
—
FTXG09HVJU
White
FTXG12HVJU
White
420 (11.9)
325 (9.2)
230 (6.5)
438 (12.4)
346 (9.8)
258 (7.3)
459 (13.0)
346 (9.8)
240 (6.8)
470 (13.3)
367 (10.4)
272 (7.7)
Cross Flow Fan
57
5 Steps, Quiet and Auto
Right, Left, Horizontal and Downward
Removable / Washable / Mildew Proof
0.12
0.14
24
26
87
80.7
Microcomputer Control
12 × 35-1/16 × 8-1/4” (305 x 891 x 210 mm)
11 × 37-5/8 × 14-7/8” (279 x 956 x 378 mm)
31 lbs (14 kg)
38 lbs (17 kg)
42 / 33 / 26
42 / 35 / 28
RXG09HVJU
Ivory White
Hermetically Sealed Swing Type
2YC36CXD
1,100
FVC50K
13.5
R-410A
3.1
1,178 (33.4)
1,095 (31.0)
—
—
Propeller
60
2.98
3.9
546
754
79.7
84.1
22-3/8 × 31-5/16 ×11-1/4”
(568 x 795 x 286 mm)
Cross Flow Fan
57
5 Steps, Quiet and Auto
Right, Left, Horizontal and Downward
Removable / Washable / Mildew Proof
0.14
0.15
29
31
90.1
89.9
Microcomputer Control
12 × 35-1/16 × 8-1/4” (305 x 891 x 210 mm)
11 × 37-5/8 × 14-7/8” (279 x 956 x 378 mm)
31 lbs (14 kg)
38 lbs (17 kg)
43 / 35 / 27
43 / 36 / 29
RXG12HVJU
Ivory White
Hermetically Sealed Swing Type
2YC36CXD
1,100
FVC50K
13.5
R-410A
3.1
1,262 (35.7)
1,111 (31.5)
—
—
Propeller
60
4.16
5.49
831
1,129
86.9
89.4
22-3/8 × 31-5/16 ×11-1/4”
(568 x 795 x 286 mm)
inch (mm)
25-3/16 ×36-7/16 ×14-7/8”
(568 x 795 x 286 mm
25-3/16 ×36-7/16 ×14-7/8”
(568 x 795 x 286 mm)
Lbs(kg)
Lbs(kg)
99 lbs (45 kg)
104 lbs (32 kg)
99 lbs (45 kg)
104 lbs (32 kg)
W
Steps
A
W
%
inch (mm)
inch (mm)
Lbs (kg)
Lbs (kg)
dBA
W
oz
Lbs
H
L
W
A
W
%
inch (mm)
dBA
46 / —
46 / —
3D062857
Note:
 The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 80°FDB/67°FWB
Indoor ; 70°FDB/60°FWB
25ft (7.5 m)
Outdoor ; 95°FDB/75°FWB
Outdoor ; 47°FDB/43°FWB
4
FTXG12HVJU
RXG12HVJU
49 / —
48 / —
3D062858
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Room Air Conditioners H-Series
EDUS04-906_b
Specifications 60Hz 230V
60Hz 230V
Indoor Units
Model
FTXG15HVJU
RXG15HVJU
Outdoor Units
Capacity
Rated (Min.~Max.)
Moisture Removal
Running Current (Rated)
Power Consumption Rated (Min.~Max.)
Power Factor
EER (Rated)
COP (Rated)
Energy
SEER/HSPF
Efficiency
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge of Refrigerant
Indoor Unit
Front Panel Color
Airflow Rate
Heating
15,000 (5,300~18,000)
18,000 (4,400~21,200)
Pt/h
A
W
%
Btu/h·W
W/W
4.8
5.64
1,160 (260~1,930)
89.0
12.9
—
—
6.36
1,320 (230~2,120)
99.0
—
3.99
21.0
feet (m)
feet (m)
feet (m)
oz/ft
H
M
L
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L
Sound
Outdoor Unit
Casing Color
Type
Compressor
Model
Motor Output
Model
Refrigerant
Oil
Charge
Model
Refrigerant
Charge
487 (13.8)
371 (10.5)
258 (7.3)
A
W
%
0.15
33
95.7
45 / 37 / 29
oz
Type
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Fan
44 / 38 / 31
RXG15HVJU
Ivory White
Hermetically Sealed Swing Type
2YC36CXD
1,100
FVC50K
13.5
R-410A
3.1
W
Lbs
H
L
0.16
35
95.1
Microcomputer Control
12 × 35-1/16 × 8-1/4” (305 x 891 x 210 mm)
11 × 37-5/8 × 14-7/8” (279 x 956 x 378 mm)
31 lbs (14 kg)
38 lbs (17 kg)
inch (mm)
inch (mm)
Lbs(kg)
Lbs(kg)
cfm (m³/min)
494 (14.0)
392 (11.1)
293 (8.3)
Cross Flow Fan
57
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
W
Steps
dBA
10.0
φ 1/4” (6.4 mmm)
φ 3/8” (9.5 mm)
φ 11/16” (17.5 mm)
Both Liquid and Gas Pipes
32’ (10 m)
26’ (8 m)
—
—
FTXG15HVJU
White
inch (mm)
inch (mm)
inch (mm)
cfm (m³/min)
Fan
Airflow Rate
Cooling
Btu/h
1,262 (35.7)
—
1,195 (33.8)
—
Propeller
60
W
A
W
%
5.49
1,127
89.3
6.2
1,285
90.1
Dimensions (H×W×D)
inch (mm)
Packaged Dimensions (H×W×D)
inch (mm)
22-3/8 × 31-5/16 ×11-1/4”
(568 x 795 x 286 mm)
25-3/16 ×36-7/16 ×14-7/8”
(568 x 795 x 286 mm)
Lbs (kg)
Lbs(kg)
99
104
Weight
Gross Weight
Operation
H/L
Sound
Drawing No.
dBA
50 / —
50 / —
3D062859
Note:
 The data are based on the conditions shown in the table below.
Conversion Formulae
Cooling
Heating
Piping Length
Indoor ; 80°FDB/67°FWB
Outdoor ; 95°FDB/75°FWB
Indoor ; 70°FDB/60°FWB
Outdoor ; 47°FDB/43°FWB
25 ft (7.5 m)
Room Air Conditioners H-Series
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
5
Dimensions
EDUS04-906_b
4. Dimensions
THE MARK (→) SHOWS PIPING DIRECTION
REQUIRED SPACE
35-1/16(890)
INCLUDING
( MOUNTING
PLATE )
10-13/16(275)
10-3/4(273)
8-1/4(209)
GEAR CASE UNIT FIXED SCREWS
(INSIDE PANEL)
BOTTOM
MULTI-COLORED INDICATOR LAMP/
INDOOR UNIT ON/OFF SWITCH
TIMER LAMP
OPERATING STATE
ROOM TEMP.
THERMISTOR
GAS PIPE φ3/8(9.5)Cut
TERMINAL BLOCK WITH EARTH TERMINAL
9/16(14.5)
BLADE ANGLE
UP/DOWN (AUTOMATIC)
COOLING
DRY COOLING
DRY
AIR PURIFYING
(INDIVIDUAL OPERATION)
HEATING
7-1/16(180)
20°
15°
30°
15°
25°
45°
60°
55°
70°
70°
55°
55°
1-7/16(37)
33(838)
9/16(15)
WALL HOLE
φ2-9/16(65)
HOLE
7-1/8(180.5)
1-1/16(26.8)
1 - 3 / 4 (44.5)
SIGNAL TRANSMITTER
DRAIN HOSE
CONNECTING PART
I.D. φ9/16(14)
O.D. φ11/16(18)
LIQUID PIPE φ1/4(6.4)Cut
SIGNAL RECEIVER
2-1/2(63)
1-15/16(50)MIN.
(SPACE FOR
PERFORMANCE)
NAME
PLATE
12 (305)
FRONT GRILL FIXED SCREWS
(INSIDE PANEL)
1-15/16(50)MIN.
(SPACE FOR
MAINTENANCE)
WALL HOLE FOR
EMBEDDED PIPING
φ2-9/16(65) HOLE
1-7/8(47)~2-3/8(60)
1-3/4(44.5)
RIGHT
LEFT
1-3/16(30)MIN.
AIR FLOW (INDOOR)
REAR
(SPACE FOR
PERFORMANCE)
FTXG09/12/15HVJU
2-5/16(59.5)
APPROX.21-9/16(548)
APPROX.23-9/16(598)
APPROX.25-13/16(655)
WIRELESS REMOTE CONTROLLER
45
°
(ARC447A3)
°
45
RIGHT/LEFT
(AUTOMATIC)
STANDARD LOCATIONS OF WALL HOLES
3D061002
1-3/16 (29.5)
RXG09/12/15HVJU
22-5/8 (574)
3-3/4 (95.5)
19-7/8 (505)
DRAIN OUTLET
(I.Dφ5/8 (15.9)
HOSE FOR CONNECTION)
4-HOLES FOR ANCHOR BOLTS
(M8 OR M10)
BRAND NAME LABEL
HANDLE
9/16 (15)
OUTDOOR AIR THERMISTOR
31-5/16 (795)
GAS STOP VALVE
(φ3/8 (9.5) CuT)
2-1/2 (63)
LIQUID
STOP VALVE
(φ1/4 (6.4) CuT)
22-3/8 (569)
SERVICE
PORT
11/16 (17)
11-1/4 (285)
1/2 (13)
1-15/16 (50)
1-15/16 (50)
6
(BASE PITCH)
4-5/8 (118)
7 (178)
IN CASE OF REMOVING
STOP VALVE COVER
1-15/16 (50)
WALL HEIGHT ON AIR OUTLET SIDE
= LESS THAN 47-3/16 (1200)
11-13/16 (300)
5-7/8 (150)
3-15/16 (100)
1-15/16 (50)
5-7/8 (150)
12-1/4 (311)
MINIMUM SPACE FOR AIR PASSAGE
2-15/16 (75)
3-1/8 (79)
5/8 (15.7)
3-15/16 (100)
13/16 (20)
NAME PLATE
UNIT=INCH (mm)
3D062671A
Room Air Conditioners H-Series
EDUS04-906_b
Wiring Diagrams
5. Wiring Diagrams
FTXG09/12/15HVJU
: PRINTED CIRCUIT BOARD
: FLAME GROUND
: FUSE
: MULTI MONITOR
: PILOT LAMP
: LIMIT SWITCH FOR PANEL
: LIMIT SWITCH FOR STREAMER
: FAN MOTOR
: SWING MOTOR
: THERMISTOR
: VARISTOR
: CONNECTOR
: OPERATION SWITCH
: TERMINAL STRIP
: SOLENOID VALVE
: FERRITE CORE
: PROTECTIVE GROUND
CAUTION
NOTE THAT OPERATION WILL
RESTART AUTOMATICALLY IF
THE MAIN POWER SUPPLY IS
TURNED OFF AND THEN BACK
ON AGAIN.
outdoor
A3P
1 2 3
SIGNAL
RECEIVER
WIRELESS
REMOTE
CONTROLLER
SIGNAL
TRANSMITTER
S58
FIELD WIRING.
BLK
BLK
BLK
BLK
BLK
JA
13
JA AN ADDRESS SETUP OF REMOTECONTROLLER
X1M 1 2 3
Z1C N=4
GRN/
YLW
GRN
RED
JUMPER
LED3 LED2 MULTI
MONITOR
H3P H2P
H1P
S56
1
WHT
S57
S1W
BLK
A1P~A5P
FG
F1U
H1P
H2P, H3P
S1C
S2C
M1F
M1S~M4S
R1T, R2T
R1V
S1~S403, CN1
S1W
X1M
Y1S, Y2S
Z1C
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
A2P
t°
A1P
R1T
1
BLK
R1V
-
S51
S1
4
7
1
7
WHT
ORG
BRN
BLU
1
RED
ORG
YLW
PNK
BLU
YLW
YLW
YLW
HUMIDITY
SENSOR
-
S41
(16PIN)
5
1
RED
S52
4
RED
ORG
YLW
PNK
BLU
S43
RED
ORG
YLW
PNK
BLU
1
1
F1U
(H250V,T3.15A)
+
YLW
1
HA
S48
BLU
ORG
WHT
BLK
RED
CN1
S21
BLK
BLK
BLK
BLK
BLK
BLK
BLK
6
BLK
BLK
BLK
BLK
BLK
BLK
FG
H3
H2
H1
S32
BLK
6
TRANSMISSION
CIRCUIT
13
S46
S91
GRN
S2C
BLK
BLK
M
M
M
M
M1S
M2S
M3S
M1F
M
5
1
S401
S403 HIGH VOLTAGE
UNIT
S402
A5P
M4S
S1C
STREAMER PART
A4P
BLK
R2T
BLK
RED
ORG
YLW
PNK
BLU
Y2S Y1S
t°
indoor
3D052768C
RXG09/12/15HVJU
FIELD WIRING.
102°C
L1
L2
L1 1
L2 2
3
X1M
Z1C
N=4
BLK
WHT
RED
GRN/
YLW
YLW
Z4C
N=2
GRN/YLW
Z2C
N=3
GRN
E2
PPL
YLW
1
2
3
L1R
1
S45
3
FU3
HL1 30A
HN1
V1
S
YLW
ORG
indoor
HR1
HR2
MRM20
MRM10
~_
SA1
IPM1
+
_
+
_
+
+ +
_ _
_
U V W
DB2
+~
V2
E1
DB1
~+
FU1
3.15A
DB3
+~
FU2
3.15A
_~
PCB1
MR4
_~
OL1 OL2 U V W
BLU
7
RED
YLW
S70
123 4
WHT
BLK
3
RED
1
WHT
ORG
BRN
BLU
S80
6
YLW
BLK
S90
YLW
1
BLK
6
BLK
S20
WHT
YLW
ORG
BLU
BRN
RED
1
outdoor
NOTE
1. REFER TO THE NAMEPLATE FOR THE POWER REQUIREMENTS.
DB1, DB2, DB3
FU1, FU2, FU3
IPM1
L1, L2
L1R
MR4, MRM10
MRM20
M1C
M1F
: DIODE BRIDGE
: FUSE
: INTELLIGENT POWER MODULE
: LIVE
: REACTOR
: MAGNETIC RELAY
: COMPRESSOR MOTOR
: FAN MOTOR
Room Air Conditioners H-Series
PCB1
Q1L
R1T, R2T, R3T
SA1
V1, V2
X1A
t°
t°
M
t°
Y1R
R1T R2T R3T
(OUTDOOR) (DISCHARGE)
(CONDENSER)
: PRINTED CIRCUIT BOARD
: OVERLOAD PROTECTOR
: THERMISTOR
: SURGE ARRESTER
: VARISTOR
: CONNECTOR
X1M
Y1E
Y1R
Z1C, Z2C, Z3C, Z4C
RED
YLW
BLU
M
Y1E
WHT
BLK
X1A
M
1~
U
M1F
Q1L
V Z3C
N=3
W
M1C
: TERMINAL STRIP
: ELECTRONIC EXPANSION VALVE COIL
: REVERSING SOLENOIDE VALVE COIL
: FERRITE CORE
: PROTECTIVE GROUND
3D061486
7
Piping Diagrams
EDUS04-906_b
6. Piping Diagrams
FTXG09/12/15HVJU
INDOOR UNIT
1/4(6.4)CuT
SV
SV
HEAT EXCHANGER
SOLENOID VALVE
AT RATED VOLTAGE: CLOSED
(UNDER DEHUMIDIFICATION
OPERATION)
THERMISTOR
ON HEAT EXCH.
CROSS FLOW FAN
M
HEAT EXCHANGER
FAN MOTOR
FIELD PIPING
1/ 4(6.4)CuT
SINGLE UNION JOINT
FIELD PIPING
3/8(9.5)CuT
3/8(9.5)CuT
SINGLE UNION JOINT
REFRIGERANT FLOW
COOLING
HEATING
4D061001
RXG09/12/15HVJU
9/32(7.0)CuT
HEAT
EXCHANGER
9/32(7.0)
THERMISTOR AUXILIARY
CuT
HEAT EXCHANGER
9/32(7.0)CuT
1/4(6.4)CuT
3/8(9.5)CuT
OUTDOOR TEMPERATURE
THERMISTOR
5/16
(7.9)CuT
FAN MOTOR
M
MUFFLER
WITH
FILTER
1/4
(6.4)CuT
1/4
(6.4)CuT
MOTOR
OPERATED
VALVE
FILTER
FILTER
PROPELLER FAN
1/2(12.7)CuT
1/4(6.4)CuT
1/2
(12.7)CuT
OUTDOOR UNIT
5/16
(7.9)CuT HEAT EXCHANGER
MUFFLER
1/4(6.4)CuT
5/16
(7.9)CuT
1/2(12.7)CuT
FOUR WAY VALVE
ON : HEATING
FIELD PIPING
LIQUID STOP (1/4(6.4)CuT)
VALVE
5/16
(7.9)CuT
MUFFLER
DISCHARGE PIPE
THERMISTOR
COMPRESSOR
1/2(12.7)CuT
MUFFLER
3/8(9.5)CuT
FIELD PIPING
GAS STOP (3/8(9.5)CuT)
VALVE
REFRIGERANT FLOW
COOLING
HEATING
UNIT=INCH(mm)
3D062171A
8
Room Air Conditioners H-Series
EDUS04-906_b
Capacity Tables
7. Capacity Tables
7.1
Heat Pump
FTXG09HVJU + RXG09HVJU (60Hz 230V)
Cooling
AFR
11.9
BF
0.10
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR TEMPERATURE (°CDB)
EWB
EDB
20.0
25.0
°C
°C
TC
SHC
PI
TC
SHC
PI
TC
SHC
30.0
PI
TC
SHC
32.0
PI
TC
SHC
35.0
PI
TC
SHC
40.0
PI
14.0
20
2.70
2.42
0.44
2.58
2.37
0.48
2.46
2.31
0.52
2.41
2.29
0.54
2.34
2.26
0.56
2.21
2.20
0.61
16.0
22
2.83
2.38
0.44
2.70
2.33
0.48
2.58
2.28
0.52
2.53
2.26
0.54
2.46
2.23
0.57
2.33
2.18
0.61
18.0
25
2.95
2.56
0.44
2.83
2.51
0.48
2.70
2.46
0.53
2.65
2.44
0.54
2.58
2.41
0.57
2.46
2.37
0.61
19.4
26.7
3.01
2.75
0.44
2.89
2.70
0.49
2.76
2.66
0.53
2.71
2.64
0.54
2.64
2.61
0.57
2.52
2.56
0.61
22.0
30
3.19
2.67
0.45
3.07
2.63
0.49
2.95
2.59
0.53
2.90
2.57
0.55
2.82
2.55
0.57
2.70
2.51
0.62
24.0
32
3.31
2.62
0.45
3.19
2.58
0.49
3.07
2.54
0.53
3.02
2.53
0.55
2.94
2.51
0.58
2.82
2.47
0.62
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FDB)
EWB
EDB
68.0
77.0
°F
°F
TC
SHC
PI
TC
SHC
PI
TC
SHC
86.0
PI
TC
SHC
89.6
PI
TC
SHC
95.0
PI
TC
104.0
SHC
PI
57.2
68.0
9.23
8.27
0.44
8.81
8.08
0.48
8.39
7.89
0.52
8.22
7.81
0.54
7.97
7.70
0.56
7.55
7.52
0.61
60.8
71.6
9.64
8.14
0.44
9.22
7.96
0.48
8.80
7.78
0.52
8.64
7.71
0.54
8.39
7.61
0.57
7.97
7.44
0.61
64.4
77.0
10.06
8.72
0.44
9.64
8.56
0.48
9.22
8.39
0.53
9.05
8.33
0.54
8.80
8.23
0.57
8.38
8.07
0.61
67.0
80.0
10.27
9.37
0.44
9.85
9.22
0.49
9.43
9.06
0.53
9.26
9.00
0.54
9.01
8.90
0.57
8.59
8.75
0.61
71.6
86.0
10.89
9.11
0.45
10.47
8.97
0.49
10.05
8.83
0.53
9.88
8.78
0.55
9.63
8.70
0.57
9.21
8.56
0.62
75.2
89.6
11.30
8.93
0.45
10.88
8.81
0.49
10.46
8.68
0.53
10.30
8.63
0.55
10.05
8.56
0.58
9.63
8.43
0.62
Heating
AFR
12.4
Temp: Celsius / TC, SHC, PI: kW
INDOOR
EDB
OUTDOOR TEMPERATURE (°CWB)
-10.0
-5.0
0
6.1
10.0
°C
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
15.0
2.39
0.66
2.79
0.69
3.19
0.72
3.67
0.76
3.98
0.78
21.1
2.25
0.68
2.65
0.71
3.04
0.74
3.52
0.78
3.84
0.81
22.0
2.22
0.68
2.62
0.71
3.02
0.74
3.50
0.78
3.81
0.81
24.0
2.18
0.69
2.57
0.72
2.97
0.75
3.45
0.79
3.77
0.82
25.0
2.15
0.69
2.55
0.72
2.95
0.76
3.42
0.79
3.74
0.82
27.0
2.10
0.70
2.50
0.73
2.90
0.76
3.37
0.80
3.69
0.83
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FWB)
EDB
14.0
23.0
32.0
43.0
50.0
°F
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
59.0
8.15
0.66
9.52
0.69
10.88
0.72
12.52
0.76
13.58
0.78
70.0
7.67
0.68
9.03
0.71
10.38
0.74
12.01
0.78
13.10
0.81
71.6
7.57
0.68
8.94
0.71
10.30
0.74
11.94
0.78
13.00
0.81
75.2
7.44
0.69
8.77
0.72
10.13
0.75
11.77
0.79
12.86
0.82
77.0
7.34
0.69
8.70
0.72
10.07
0.76
11.67
0.79
12.76
0.82
80.6
7.17
0.70
8.53
0.73
9.89
0.76
11.50
0.80
12.59
0.83
Room Air Conditioners H-Series
9
Capacity Tables
EDUS04-906_b
Symbols
AFR
: Airflow rate
Note:
(m3/min.)
BF
: Bypass factor
EWB
: Entering wet bulb temp.
EDB
: Entering dry bulb temp.
(°C) / (°F)
TC
: Total capacity
(kW) / (kBtu/h)
(°C) / (°F)
SHC
: Sensible heating capacity (kW) / (kBtu/h)
PI
: Power input
(kW)
1. Ratings shown are net capacities which include a deduction for indoor fan
motor heat.
2.
shows nominal (rated) capacities and power input.
3. TC, PI and SHC must be calculated by interpolation using the figures in
the above tables. (Figures outof the tables should not be used for
calculation.)
4. About SHC which are not mentioned on the table, please calculate them
with around values in direct proportion.
5. Capacities are based on the following conditions.
Corresponding refrigerant piping length : 25ft (7.5 m)
Level difference : 0ft
6. Airflow rate (AFR) and Bypass factor (BF) are tabulated above table.
7. Cooling capacity at -10 degrees Celsius / 14 degrees Fahrenheit.
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR
EWB
EDB
°C
°C
TC
-10 (°CDB)
SHC
PI
14.0
20
3.44
2.77
0.31
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR
EWB
EDB
°F
°F
TC
14 (°FDB)
SHC
PI
57.2
68.0
11.75
9.44
0.31
3D063098A
10
Room Air Conditioners H-Series
EDUS04-906_b
Capacity Tables
FTXG12HVJU + RXG12HVJU (60Hz 230V)
Cooling
AFR
13.0
BF
0.14
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR TEMPERATURE (°CDB)
EWB
EDB
20.0
25.0
°C
°F
TC
SHC
PI
TC
SHC
PI
TC
SHC
30.0
PI
TC
SHC
32.0
PI
TC
SHC
35.0
PI
TC
SHC
40.0
PI
14.0
20
3.61
2.86
0.66
3.44
2.78
0.72
3.28
2.71
0.79
3.21
2.68
0.81
3.11
2.63
0.85
2.95
2.55
0.91
16.0
22
3.77
2.81
0.66
3.60
2.74
0.73
3.44
2.67
0.79
3.38
2.64
0.82
3.28
2.60
0.85
3.11
2.53
0.92
18.0
25
3.93
2.98
0.67
3.77
2.91
0.73
3.60
2.84
0.79
3.54
2.81
0.82
3.44
2.77
0.86
3.28
2.71
0.92
19.4
26.7
4.01
3.16
0.67
3.85
3.10
0.73
3.68
3.03
0.80
3.62
3.01
0.82
3.52
2.97
0.86
3.36
2.91
0.92
22.0
30
4.25
3.06
0.67
4.09
3.00
0.74
3.93
2.95
0.80
3.86
2.92
0.83
3.76
2.89
0.87
3.60
2.83
0.93
24.0
32
4.42
2.99
0.68
4.25
2.94
0.74
4.09
2.88
0.81
4.02
2.86
0.83
3.93
2.83
0.87
3.76
2.78
0.93
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FDB)
EWB
EDB
68.0
77.0
°F
°F
TC
SHC
PI
TC
SHC
PI
TC
SHC
86.0
PI
TC
SHC
89.6
PI
TC
SHC
95.0
PI
TC
104.0
SHC
PI
57.2
68.0
12.30
9.77
0.66
11.75
9.50
0.72
11.19
9.24
0.79
10.96
9.13
0.81
10.63
8.98
0.85
10.07
8.72
0.91
60.8
71.6
12.86
9.60
0.66
12.30
9.35
0.73
11.74
9.11
0.79
11.52
9.01
0.82
11.18
8.86
0.85
10.62
8.62
0.92
64.4
77.0
13.41
10.15
0.67
12.85
9.92
0.73
12.29
9.69
0.79
12.07
9.60
0.82
11.73
9.46
0.86
11.17
9.24
0.92
66.9
80.1
13.69
10.80
0.67
13.13
10.57
0.73
12.57
10.35
0.80
12.35
10.26
0.82
12.01
10.13
0.86
11.45
9.91
0.92
71.6
86.0
14.52
10.44
0.67
13.96
10.25
0.74
13.40
10.05
0.80
13.18
9.97
0.83
12.84
9.86
0.87
12.28
9.67
0.93
75.2
89.6
15.07
10.20
0.68
14.51
10.02
0.74
13.95
9.84
0.81
13.73
9.77
0.83
13.39
9.66
0.87
12.83
9.49
0.93
Heating
AFR
13.3
Temp: Celsius / TC, SHC, PI: kW
INDOOR
EDB
OUTDOOR TEMPERATURE (°CWB)
-10.0
-5.0
0
6.1
10.0
°C
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
15.0
3.19
0.98
3.72
1.02
4.25
1.07
4.88
1.13
5.31
1.17
21.1
3.00
1.01
3.52
1.05
4.05
1.10
4.69
1.16
5.11
1.20
22.0
2.96
1.01
3.49
1.06
4.02
1.11
4.66
1.17
5.08
1.20
24.0
2.90
1.02
3.43
1.07
3.96
1.12
4.59
1.18
4.72
1.18
25.0
2.87
1.03
3.40
1.08
3.92
1.12
4.52
1.17
4.52
1.16
27.0
2.80
1.04
3.33
1.09
3.86
1.13
4.11
1.13
4.11
1.12
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FWB)
EDB
14.0
23.0
32.0
43.0
50.0
°F
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
59.0
10.88
0.98
12.69
1.02
14.50
1.07
16.65
1.13
18.12
1.17
70.0
10.22
1.01
12.03
1.05
13.83
1.10
16.00
1.16
17.45
1.20
71.6
10.10
1.01
11.91
1.06
13.72
1.11
15.90
1.17
17.33
1.20
75.2
9.89
1.02
11.70
1.07
13.51
1.12
15.66
1.18
16.11
1.18
77.0
9.79
1.03
11.60
1.08
13.38
1.12
15.41
1.17
15.41
1.16
80.6
9.55
1.04
11.36
1.09
13.17
1.13
14.01
1.13
14.01
1.12
Room Air Conditioners H-Series
11
Capacity Tables
EDUS04-906_b
Symbols
AFR
: Airflow rate
Note:
(m3/min.)
BF
: Bypass factor
EWB
: Entering wet bulb temp.
EDB
: Entering dry bulb temp.
(°C) / (°F)
TC
: Total capacity
(kW) / (kBtu/h)
(°C) / (°F)
SHC
: Sensible heating capacity (kW) / (kBtu/h)
PI
: Power input
(kW)
1. Ratings shown are net capacities which include a deduction for indoor fan
motor heat.
2.
shows nominal (rated) capacities and power input.
3. TC, PI and SHC must be calculated by interpolation using the figures in
the above tables. (Figures out of the tables should not be used for
calculation.)
4. About SHC which are not mentioned on the table, please calculate them
with around values in direct proportion.
5. Capacities are based on the following conditions.
Corresponding refrigerant piping length : 25ft (7.5 m)
Level difference : 0ft
6. Airflow rate (AFR) and Bypass factor (BF) are tabulated above table.
7. Cooling capacity at -10 degrees Celsius / 14 degrees Fahrenheit.
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR
EWB
EDB
°C
°C
TC
-10 (°CDB)
SHC
PI
14.0
20
3.65
2.66
0.47
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR
EWB
EDB
°F
°F
TC
14 (°FDB)
SHC
PI
57.2
68.0
12.45
9.08
0.47
3D063099A
12
Room Air Conditioners H-Series
EDUS04-906_b
Capacity Tables
FTXG15HVJU + RXG15HVJU (60Hz 230V)
Cooling
AFR
13.8
BF
0.16
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR TEMPERATURE (°CDB)
EWB
EDB
20.0
25.0
°C
°C
TC
SHC
PI
TC
SHC
PI
TC
SHC
30.0
PI
TC
SHC
32.0
PI
TC
SHC
35.0
PI
TC
SHC
40.0
PI
14.0
20
4.51
3.36
0.89
4.30
3.26
0.98
4.10
3.15
1.06
4.02
3.11
1.10
3.89
3.05
1.15
3.69
2.96
1.23
16.0
22
4.71
3.30
0.90
4.51
3.20
0.98
4.30
3.11
1.07
4.22
3.07
1.10
4.10
3.01
1.15
3.89
2.92
1.24
18.0
25
4.91
3.46
0.90
4.71
3.37
0.99
4.50
3.28
1.07
4.42
3.24
1.11
4.30
3.19
1.16
4.09
3.11
1.24
19.4
26.7
5.01
3.65
0.90
4.81
3.56
0.99
4.60
3.48
1.07
4.52
3.44
1.11
4.40
3.39
1.16
4.20
3.31
1.25
22.0
30
5.32
3.52
0.91
5.11
3.44
1.00
4.91
3.37
1.08
4.83
3.34
1.12
4.70
3.29
1.17
4.50
3.22
1.25
24.0
32
5.52
3.43
0.92
5.32
3.36
1.00
5.11
3.29
1.09
5.03
3.26
1.12
4.91
3.22
1.17
4.70
3.15
1.26
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FDB)
EWB
EDB
68.0
77.0
°F
°F
TC
SHC
PI
TC
SHC
PI
TC
SHC
86.0
PI
TC
SHC
89.6
PI
TC
SHC
95.0
PI
TC
104.0
SHC
PI
57.2
68.0
15.38
11.46
0.89
14.68
11.11
0.98
13.98
10.76
1.06
13.70
10.62
1.10
13.28
10.42
1.15
12.58
10.08
1.23
60.8
71.6
16.07
11.26
0.90
15.37
10.93
0.98
14.67
10.60
1.07
14.39
10.48
1.10
13.98
10.28
1.15
13.28
9.97
1.24
64.4
77.0
16.76
11.80
0.90
16.07
11.49
0.99
15.37
11.19
1.07
15.09
11.07
1.11
14.67
10.89
1.16
13.97
10.60
1.24
67.0
80.0
17.11
12.45
0.90
16.41
12.15
0.99
15.71
11.86
1.07
15.43
11.75
1.11
15.01
11.58
1.16
14.31
11.29
1.25
71.6
86.0
18.15
12.00
0.91
17.45
11.75
1.00
16.75
11.49
1.08
16.47
11.39
1.12
16.05
11.24
1.17
15.35
10.98
1.25
75.2
89.6
18.84
11.69
0.92
18.14
11.45
1.00
17.44
11.22
1.09
17.16
11.13
1.12
16.74
10.99
1.17
16.04
10.76
1.26
Heating
AFR
14.0
Temp: Celsius / TC, SHC, PI: kW
INDOOR
EDB
OUTDOOR TEMPERATURE (°CWB)
-10.0
-5.0
0
6.1
10.0
°C
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
15.0
3.59
1.11
4.19
1.16
4.78
1.22
5.50
1.28
5.98
1.33
21.1
3.37
1.15
3.97
1.20
4.56
1.25
5.28
1.32
5.62
1.34
22.0
3.34
1.15
3.93
1.21
4.53
1.26
5.24
1.33
5.41
1.32
24.0
3.26
1.16
3.86
1.22
4.46
1.27
4.97
1.31
4.97
1.28
25.0
3.23
1.17
3.82
1.22
4.42
1.28
4.76
1.28
4.76
1.26
27.0
3.15
1.18
3.75
1.24
4.33
1.29
4.33
1.23
4.33
1.20
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR TEMPERATURE (°FWB)
EDB
14.0
23.0
32.0
43.0
50.0
°F
TC
PI
TC
PI
TC
PI
TC
PI
TC
PI
59.0
12.25
1.11
14.29
1.16
16.32
1.22
18.76
1.28
20.39
1.33
70.0
11.51
1.15
13.54
1.20
15.57
1.25
18.02
1.32
19.19
1.34
71.6
11.38
1.15
13.42
1.21
15.45
1.26
17.89
1.33
18.45
1.32
75.2
11.13
1.16
13.17
1.22
15.20
1.27
16.97
1.31
16.97
1.28
77.0
11.01
1.17
13.04
1.22
15.08
1.28
16.23
1.28
16.23
1.26
80.6
10.76
1.18
12.79
1.24
14.76
1.29
14.76
1.23
14.76
1.20
Room Air Conditioners H-Series
13
Capacity Tables
EDUS04-906_b
Symbols
AFR
: Airflow rate
Note:
(m3/min.)
BF
: Bypass factor
EWB
: Entering wet bulb temp.
EDB
: Entering dry bulb temp.
(°C) / (°F)
TC
: Total capacity
(kW) / (kBtu/h)
(°C) / (°F)
SHC
: Sensible heating capacity (kW) / (kBtu/h)
PI
: Power input
(kW)
1. Ratings shown are net capacities which include a deduction for indoor fan
motor heat.
2.
shows nominal (rated) capacities and power input.
3. TC, PI and SHC must be calculated by interpolation using the figures in
the above tables. (Figures out of the tables should not be used for
calculation.)
4. About SHC which are not mentioned on the table, please calculate them
with around values in direct proportion.
5. Capacities are based on the following conditions.
Corresponding refrigerant piping length : 25ft (7.5 m)
Level difference : 0ft
6. Airflow rate (AFR) and Bypass factor (BF) are tabulated above table.
7. Cooling capacity at -10 degrees Celsius / 14 degrees Fahrenheit.
Temp: Celsius / TC, SHC, PI: kW
INDOOR
OUTDOOR
EWB
EDB
°C
°C
TC
-10 (°CDB)
SHC
PI
14.0
20
3.66
2.70
0.46
Temp: Fahrenheit / TC, SHC: kBtu / PI: kW
INDOOR
OUTDOOR
EWB
EDB
°F
°F
TC
14 (°FDB)
SHC
PI
57.2
68.0
12.49
9.21
0.46
3D063100A
14
Room Air Conditioners H-Series
EDUS04-906_b
Operation Limit
8. Operation Limit
RXG09/12/15HVJU
Heating
Cooling
77
75
109
104
68
59
41
32
23
Continuous operation
50
Outdoor temp. (°FWB)
68
50
Pull-down period
Continuous operation
Outdoor temp. (°FDB)
86
32
14
5
14
-4
(-4°FDB)
50
59
68 73.4 77 82.4 86
Indoor temp. (°FWB)
Notes:
The graphs are based
on the following conditions.
• Equivalent piping length 25ft
• Level difference
0ft
• Air flow rate
High
Room Air Conditioners H-Series
50
68
Indoor temp. (°FDB)
86
3D063096
15
Sound Level
EDUS04-906_b
9. Sound Level
9.1
Measuring Location
Indoor Unit
2.6ft
3.3ft
(R5162)
Outdoor Unit
3.3ft
(R4796)
Note:
1. Operation sound is measured in an anechoic chamber.
2. The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 80°FDB/67°FWB
Outdoor ; 95°FDB/75°FWB
Indoor ; 70°FDB/60°FWB
Outdoor ; 47°FDB/43°FWB
16.4ft (5 m)
16
Room Air Conditioners H-Series
EDUS04-906_b
Sound Level
9.2
Octave Band Level
9.2.1
Indoor Units
FTXG09HVJU
COOLING
70
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
42
26
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
208/230V 60Hz
POWER SOURCE
40
JIS STANDARD
STANDARD EXTERNAL STATIC PRESSURE
NC-30
30
60Hz 208/230V(H)
60Hz 208/230V(L)
NC-20
20
Cooling
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
42
28
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
208/230V 60Hz
POWER SOURCE
40
JIS STANDARD
STANDARD EXTERNAL STATIC PRESSURE
NC-30
30
60Hz 208/230V(H)
60Hz 208/230V(L)
NC-20
20
Heating
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
8000
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
3D063060
8000
FTXG12HVJU
COOLING
70
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
43
27
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
POWER SOURCE
40
208/230V 60Hz
JIS STANDARD
STANDARD EXTERNAL STATIC PRESSURE
NC-30
30
60Hz 208/230V(H)
60Hz 208/230V(L)
NC-20
20
Cooling
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
43
29
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
208/230V 60Hz
POWER SOURCE
40
JIS STANDARD
STANDARD EXTERNAL STATIC PRESSURE
NC-30
30
60Hz 208/230V(H)
60Hz 208/230V(L)
NC-20
20
Heating
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
8000
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
3D063061
8000
FTXG15HVJU
COOLING
70
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
45
29
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
POWER SOURCE
40
208/230V 60Hz
JIS STANDARD
STANDARD EXTERNAL STATIC PRESSURE
NC-30
30
60Hz 208/230V(H)
60Hz 208/230V(L)
NC-20
20
Cooling
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
Room Air Conditioners H-Series
8000
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208/230V
(H)
60Hz
208/230V
(L)
A
44
31
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
POWER SOURCE
40
208/230V 60Hz
JIS STANDARD
NC-30
STANDARD EXTERNAL STATIC PRESSURE
60Hz 208/230V(H)
NC-20
Heating
30
60Hz 208/230V(L)
20
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
8000
3D063080
17
Sound Level
9.2.2
EDUS04-906_b
Outdoor Units
RXG09HVJU
COOLING
NC-60
60
NC-50
SCALE
60Hz
208-230V
A
46
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
POWER SOURCE
40
208-230V 60Hz
JIS STANDARD (JIS9612)
Cooling
NC-30
30
NC-20
20
70
OVER ALL ( dB )
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208-230V
A
46
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
NC-40
POWER SOURCE
40
208-230V 60Hz
JIS STANDARD (JIS9612)
Heating
NC-30
30
NC-20
20
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
8000
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
3D063010
8000
RXG12HVJU
COOLING
NC-60
60
NC-50
SCALE
60Hz
208-230V
A
49
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
POWER SOURCE
NC-40
40
208-230V 60Hz
JIS STANDARD (JIS9612)
Cooling
NC-30
30
NC-20
20
70
OVER ALL ( dB )
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER ALL ( dB )
NC-60
60
NC-50
SCALE
60Hz
208-230V
A
48
( B.G.N IS ALREADY RECTIFIED )
50
OPERATING CONDITIONS
POWER SOURCE
NC-40
40
208-230V 60Hz
JIS STANDARD (JIS9612)
Heating
NC-30
30
NC-20
20
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
8000
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY (Hz)
3D063011
8000
RXG15HVJU
COOLING
NC-60
NC-60
60
NC-50
NC-50
60Hz
208-230V
208/230V
A
A
50
51
OPERATING CONDITIONS
NC-40
NC-40
40
POWER SOURCE
208-230V
208/230V60Hz
60Hz
JIS STANDARD
(JIS9612)
JIS STANDARD
Cooling
60Hz 208/230V
NC-30
30
Cooling
NC-20
NC-20
APPROXIMATE
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
18
SCALE
( B.G.N IS ALREADY
ALREADY RECTIFIED )
50
20
70
OVER
OVER ALL ( dB )
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY
FREQUENCY (Hz)
8000
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
OCTAVE BAND SOUND PRESSURE LEVEL
dB(0dB=0.0002μ bar)
70
HEATING
OVER
OVER ALL ( dB )
NC-60
NC-60
60
NC-50
NC-50
SCALE
60Hz
60Hz
208/230V
208-230V
A
50
51
( B.G.N IS ALREADY
ALREADY RECTIFIED )
50
OPERATING CONDITIONS
POWER SOURCE
NC-40
NC-40
40
208-230V 60Hz
60Hz
208/230V
JIS STANDARD
(JIS9612)
JIS STANDARD
Heating
60Hz 208/230V
NC-30
30
Heating
NC-20
NC-20
20
APPROXIMATE
APPROXIMATE
THRESHOLD HEARING
FOR CONTINUOUS
NOISE
63
125
250
500 1000 2000 4000
OCTAVE BAND CENTER FREQUENCY
FREQUENCY (Hz)
8000
3D063012
3D047647A
Room Air Conditioners H-Series
EDUS04-906_b
Electric Characteristics
10. Electric Characteristics
Representative Unit Combination
Indoor Unit
Outdoor Unit
FTXG09HVJU
RXG09HVJU
FTXG12HVJU
FTXG15HVJU
RXG12HVJU
RXG15HVJU
Power Supply
COMP
Hz-Volts
Voltage Range
MCA
MOP
RHz
60-208
MAX. 60Hz 253V
MIN. 60Hz 187V
14.5
15
29
60-230
60-208
60-230
60-208
60-230
MAX. 60Hz 253V
MIN. 60Hz 187V
MAX. 60Hz 253V
MIN. 60Hz 187V
14.5
14.5
15
15
43
54
RLA
2.3
2.1
3.7
3.3
5.1
4.6
OFM
IFM
W
FLA
W
60
0.10
57
60
60
0.13
0.13
57
57
FLA
0.13
0.12
0.15
0.14
0.17
0.15
Symbols:
Note:
MCA
: MIN. CIRCUIT AMPS (A)
MOP
: MAX. OVERCURRENT PROTECTION (A)
1. RLA is based on the following conditions.
Indoor temp. : 80°FDB / 67°FWB (26.7°CDB / 19.4°CWB)
Outdoor temp. : 95°FDB (35°CDB)
2. Maximum allowable voltage variation between phases is 2%.
3. Select wire size based on the larger value of MCA.
4. Instead of fuse, use circuit breaker.
5. Be sure to install a ground leak detector. (One that can handle
higher harmonics.)
(This unit uses an inverter, which means that it must be used a
ground leak detector capable handling high harmonics in order to
prevent malfunctioning of the ground leak detector itself.)
RLA
: RATED LOAD AMPS (A)
OFM
: OUTDOOR FAN MOTOR
IFM
: INDOOR FAN MOTOR
FLA
: FULL LOAD AMPS (A)
W
: FAN MOTOR RATED OUTPUT (W)
RHz
: RATED OPERATING FREQUENCY (Hz)
3D063013
Room Air Conditioners H-Series
19
Installation Manual
EDUS04-906_b
11. Installation Manual
11.1
Indoor Units
Read these SAFETY CONSIDERATIONS for Installation
carefully before installing an air conditioner or heat pump.
After completing the installation, make sure that the unit
operates properly during the startup operation.
Instruct the customer on how to operate and maintain the unit.
Inform customers that they should store this Installation
Manual with the Operation Manual for future reference.
Always use a licensed installer or contractor to install this
product. Improper installation can result in water or refrigerant
leakage, electrical shock, fire, or explosion.
Meanings of DANGER, WARNING, CAUTION, and NOTE
Symbols:
DANGER .............. Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING ............ Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION ............. Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
NOTE .................. Indicates situations that may result in
equipment or property-damage
accidents only.
• Refrigerant gas is heavier than air and replaces oxygen.
A massive leak can lead to oxygen depletion, especially
in basements, and an asphyxiation hazard could occur
leading to serious injury or death.
• Do not ground units to water pipes, gas pipes,
telephone wires, or lightning rods as incomplete
grounding can cause a severe shock hazard resulting
in severe injury or death. Additionally, grounding to
gas pipes could cause a gas leak and potential
explosion causing severe injury or death.
• If refrigerant gas leaks during installation, ventilate
the area immediately. Refrigerant gas may produce
toxic gas if it comes into contact with fire. Exposure to
this gas could cause severe injury or death.
• After completing the installation work, check that the
refrigerant gas does not leak throughout the system.
• Do not install unit in an area where flammable
materials are present due to risk of explosions that
can cause serious injury or death.
• Safely dispose all packing and transportation
materials in accordance with federal/state/local laws
or ordinances. Packing materials such as nails and
other metal or wood parts, including plastic packing
materials used for transportation may cause injuries
or death by suffocation.
20
• Only qualified personnel must carry out the installation
work. Installation must be done in accordance with this
installation manual. Improper installation may result in
water leakage, electric shock, or fire.
• When installing the unit in a small room, take measures
to keep the refrigerant concentration from exceeding
allowable safety limits. Excessive refrigerant leaks, in
the event of an accident in a closed ambient space, can
lead to oxygen deficiency.
• Use only specified accessories and parts for
installation work. Failure to use specified parts may
result in water leakage, electric shocks, fire, or the
unit falling.
• Install the air conditioner or heat pump on a
foundation strong enough that it can withstand the
weight of the unit. A foundation of insufficient
strength may result in the unit falling and causing
injuries.
• Take into account strong winds, typhoons, or
earthquakes when installing. Improper installation
may result in the unit falling and causing accidents.
• Make sure that a separate power supply circuit is
provided for this unit and that all electrical work is
carried out by qualified personnel according to local.
state, and national regulations. An insufficient power
supply capacity or improper electrical construction
may lead to electric shocks or fire.
• Make sure that all wiring is secured, that specified
wires are used, and that no external forces act on the
terminal connections or wires. Improper connections
or installation may result in fire.
• When wiring, position the wires so that the terminal
box lid can be securely fastened. Improper
positioning of the terminal box lid may result in
electric shocks, fire, or the terminals overheating.
• Before touching electrical parts, turn off the unit.
• It is recommended to install a ground fault circuit
interrupter if one is not already available. This helps
prevent electrical shocks or fire.
• Securely fasten the outside unit terminal cover
(panel). If the terminal cover/panel is not installed
properly, dust or water may enter the outside unit
causing fire or electric shock.
• When installing or relocating the system, keep the
refrigerant circuit free from substances other than the
specified refrigerant (R-410A) such as air. Any
presence of air or other foreign substance in the
refrigerant circuit can cause an abnormal pressure
rise or rupture, resulting in injury.
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
• Do not change the setting of the protection devices. If
the pressure switch, thermal switch, or other
protection device is shorted and operated forcibly, or
parts other than those specified by Daikin are used,
fire or explosion may occur.
• Remote controller (wireless kit) transmitting distance
can be shorter than expected in rooms with electronic
fluorescent lamps (inverter or rapid start types).
Install the indoor unit far away from fluorescent lamps
as much as possible.
• Do not touch the switch with wet fingers. Touching a
switch with wet fingers can cause electric shock.
• Indoor units are for indoor installation only. Outdoor
units can be installed either outdoors or indoors. This
unit is for indoor use.
• Do not allow children to play on or around the unit to
prevent injury.
• Do not touch the refrigerant pipes during and
immediately after operation as the refrigerant pipes
may be hot or cold, depending on the condition of the
refrigerant flowing through the refrigerant piping,
compressor, and other refrigerant cycle parts. Your
hands may suffer burns or frostbite if you touch the
refrigerant pipes. To avoid injury, give the pipes time
to return to normal temperature or, if you must touch
them, be sure to wear proper gloves.
• Install drain piping to proper drainage. Improper drain
piping may result in water leakage and property
damage.
• Insulate piping to prevent condensation.
• Be careful when transporting the product.
• Do not turn off the power immediately after stopping
operation. Always wait for at least 5 minutes before
turning off the power. Otherwise, water leakage may
occur.
• Do not use a charging cylinder. Using a charging
cylinder may cause the refrigerant to deteriorate.
• Refrigerant R-410A in the system must be kept clean,
dry, and tight.
(a) Clean and Dry -- Foreign materials (including
mineral oils such as SUNISO oil or moisture)
should be prevented from getting into the system.
(b) Tight -- R-410A does not contain any chlorine,
does not destroy the ozone layer, and does not
reduce the earth’s protection again harmful
ultraviolet radiation. R-410A can contribute to the
greenhouse effect if it is released. Therefore take
proper measures to check for the tightness of the
refrigerant piping installation. Read the chapter
Refrigerant Piping and follow the procedures.
• Since R-410A is a blend, the required additional
refrigerant must be charged in its liquid state. If the
refrigerant is charged in a state of gas, its
composition can change and the system will not work
properly.
• Do not install the air conditioner or heat pump in the
following locations:
(a) Where a mineral oil mist or oil spray or vapor is
produced, for example, in a kitchen.
Plastic parts may deteriorate and fall off or result in
water leakage.
(b) Where corrosive gas, such as sulfurous acid gas, is
produced.
Corroding copper pipes or soldered parts may result
in refrigerant leakage.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation of
the control system and cause the unit to
malfunction.
(d) Where flammable gas may leak, where there is
carbon fiber, or ignitable dust suspension in the air,
or where volatile flammables such as thinner or
gasoline are handled. Operating the unit in such
conditions can cause a fire.
• Take adequate measures to prevent the outside unit
from being used as a shelter by small animals. Small
animals making contact with electrical parts can
cause malfunctions, smoke, or fire. Instruct the
customer to keep the area around the unit clean.
• Install the power supply and control wires for the indoor
and outdoor units at least 3.5 feet away from televisions
or radios to prevent image interference or noise.
Depending on the radio waves, a distance of 3.5 feet may
not be sufficient to eliminate the noise.
• Dismantling the unit, treatment of the refrigerant, oil
and additional parts must be done in accordance with
the relevant local, state, and national regulations.
• Do not use the following tools that are used with
conventional refrigerants: gauge manifold, charge
hose, gas leak detector, reverse flow check valve,
refrigerant charge base, vacuum gauge, or refrigerant
recovery equipment.
• If the conventional refrigerant and refrigerator oil are
mixed in R-410A, the refrigerant may deteriorate.
• This air conditioner or heat pump is an appliance that
should not be accessible to the general public.
• As design pressure is 478 psi, the wall thickness of
field-installed pipes should be selected in accordance
with the relevant local, state, and national regulations.
• The indoor unit is for R-410A. See the catalog for
indoor models that can be connected. Normal
operation is not possible when connected to other
units.
Room Air Conditioners H-Series
21
Installation Manual
EDUS04-906_b
Accessories
22
A Mounting plate
1
E Wireless remote controller
1
J Installation manual
1
B Deodorizing filter for streamer
1
F Remote controller holder
1
K Mounting plate fixing screws
3/16” × 1”L (M4 × 25mm)
9
C Titanium apatite photocatalytic
air-purifying filter
1
G Dry batteries AAA. LR03
(alkaline)
2
L Fixing screws for remote
controller holder
1/8” × 13/16”L (M3 × 20mm)
2
D Indoor unit fixing screws
3/16” × 1/2”L (M4 × 12mm)
3
H Operation manual
1
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
Indoor Unit Installation Drawings
1.
Removing and installing indoor unit.
• Installation method
1) Using the
marks (3 locations) on top of the
indoor unit, attach the A mounting plate hooks
onto the indoor unit.
2) Attach the tabs on the bottom frame onto the
A mounting plate. If the tabs are not hooked onto
the plate, remove the front grille to hook them.
(Check to see if the tabs are hooked securely.)
A Mounting
A Mounting
plate
plate
Bottom
frame
Mark
(rear side)
• Removal method
Tab
Push up the mark part on the bottom of the front
grille, discharge the tabs, and then remove the unit
while lifting it up.
A Mounting plate
To remove the unit, push up the bottom of the bottom
frame with your fingers to free tabs.
(Mark parts (2 locations) on the bottom of the front grille.)
How to open the service lid
The A mounting plate
should be installed on a
wall which can support the
weight of the indoor unit.
The service lid is
removable.
 Opening the lid
1) Remove the screws
on the service lid.
2) Hold the knobs on the
service lid and pull
forward.
Supporting plate
Use when
opening the
front panel and
securing.
2)
1)
Supporting plate
K Mounting plate fixing
screws 3/16” × 1”L (M4 × 25mm) (9)
Front panel
The securing tape is applied.
Be sure to remove it before
installation.
1-3/16” (30mm)
or more
from ceiling
Cut thermal insulation pipe
to an appropriate length and
wrap it with tape, making
sure that no gap is left in the
insulation pipe’s cut line.
1-15/16” (50mm)
or more from walls
(on both sides)
Install the
hose with a
downward
slope.
C Titanium apatite
photocatalytic
air-purifying filter
Wrap the insulation
pipe with the finishing
tape from bottom to top.
B Deodorizing filter
Air filter
for streamer
E Wireless
remote controller
Set the
G dry batteries
AAA. LR03
(alkaline)
Hook
F
Remote
controller holder
L Fixing screws for remote
controller holder
1/8” × 13/16”L (M3 × 20mm) (2)
Before screwing the
remote controller
holder to the wall,
make sure that control
signals are properly
received by indoor unit.
3
Room Air Conditioners H-Series
23
Installation Manual
EDUS04-906_b
Installation Tips
1.
Removing and installing front panel.
Rotating shaft
Rotating shaft
• Removal method
1) Open the front panel.
2) Spread out the shaft hole on the left side and
remove the rotating shaft.
Spread out the shaft hole on the right side as well
and remove the rotating shaft.
Shaft hole
Shaft hole
• Installation method
Insert the right and left rotating shafts on the front
panel into the shaft holes one at a time and slowly
close the panel.
(Press on both sides of the front panel.)
Shaft hole
2.
Rotating shaft
Removing and installing the upper panel.
Tab (Center)
• Removal method
1) Remove the front panel and air filter.
2) Hold and pull forward 2 tabs on both sides to discharge them,
discharge the center tab, and then lift up the upper panel.
Tabs
(2 on both sides)
• Installation method
Tabs (3 locations)
1) Push in the upper panel along the guide on the top of the
front grille and insert the 3 tabs into the slots on the front
grille.
2) Push the upper panel down until it clicks.
3) Attach the air filter and front panel.
3.
Removing and installing the front grille.
• Removal method
1)
2)
3)
4)
Remove the front panel, air filter and upper panel.
Fully open the top and bottom horizontal louvers. (See Fig. 1)
Remove the 3 screws in the front grille.
Lift the hooks (3 locations) on the front grille with a flathead
screwdriver to discharge the tab.
(Look for the  mark.) (See Fig. 2)
5) Pull forward the front grille to remove.
Fig. 1
Horizontal louver
Top horizontal louver
When removing or
attaching the front grille,
pay attention to open or
close of each horizontal
louver.
Bottom horizontal louver
• Installation method
1) Open the top louver fully and close the bottom louver fully.
2) Store the gear case arm in the front grille. (See Fig. 3)
3) Attach the front grille to the lower part of the unit.
(Use caution not to pinch the horizontal louver.)
4) Make sure to firmly latch the top hooks (3 locations).
5) Tighten with the 3 front grille screws.
6) Attach the upper panel, air filter and front panel.
Fig. 3
Gear case arm
Fig. 2
Hooks on the front grille
 mark area (3 locations)
CAUTION
Use caution to prevent the
front grille from breaking.
 mark area (3 locations)
Be sure to
store the
gear case
arm before
attaching the
front grille.
Upper panel
4
24
Room Air Conditioners H-Series
EDUS04-906_b
4.
Installation Manual
Installing the titanium apatite
photocatalytic air-purifying filter
and deodorizing filter for streamer.
1) Open the front panel to pull out the air filter.
2) Attach the C titanium apatite photocatalytic airpurifying filter.
3) Attach the B deodorizing filter for streamer.
4) Replace the air filter to its original position and close
the front panel.
5.
How to replace the drain plug and
drain hose.
• Replacing onto the left side
1) Remove the insulation fixing screws on the right to
remove the drain hose.
2) Reattach the insulation fixing screw on the right as it was.
*(Forgetting to attach this may cause water leakages.)
3) Remove the drain plug on the left side and attach it to
the right side.
4) Insert the drain hose and tighten with included
D indoor unit fixing screw.
Left side
Right side
C Titanium apatite
B Deodorizing filter
photocatalytic
air-purifying filter
for streamer
Drain hose attachment position
* The drain hose is on the back of the unit.
Left side
Right side
Front side of unit
Attachment on the left side
Attachment on the right side (factory default)
Insulation
fixing screw
D Indoor unit
fixing screw
Drain hose
How to set drain plug.
Drain hose
Do not apply lubricating
oil (refrigerant oil) when
inserting.
Application of causes
deterioration and drain
leakage of the plug.
ap.
No g
Insert a hexagon wrench (3/16 inch (4mm)).
6.
How to set the different addresses.
• When 2 indoor units are installed in 1 room, the
2 wireless remote controllers can be set for different
addresses.
1) Remove the front grille. (3 screws)
2) Cut the address jumper “JA”. (See Fig. 1)
Fig. 1
Electric parts box cover
Cut JA.
3) Remove the remote controller lid and cut the
address jumper “J4”. (See Fig. 2)
Fig. 2
Cut section
J4
5
Room Air Conditioners H-Series
25
Installation Manual
EDUS04-906_b
Indoor Unit Installation
1.
Installing the mounting plate.
• The
A
mounting plate should be installed on a wall which can support the weight of the indoor unit.
1) Temporarily secure the A mounting plate to the wall, make sure that the panel is completely level, and mark the boring
points on the wall.
2) Secure the A mounting plate to the wall with screws.
Recommended mounting plate retention spots and Dimensions
5/8
(Bolt size : 3/8 (M10))
(15)
11-3/16 (285)
5-11/16 (145)
6-1/2 (165)
Through the wall
hole φ2-9/16 (65)
Drain hose
position
4-3/4
(120)
3-15/16
(100)
21-9/16 (548)
φ2-9/16 (65)
φ2-9/16 (65)
1-3/4
(44.5)
1-3/4
(44.5)
Use tape
measure
as shown.
Position the
end of a tape
measure at ∇.
10-1/4 (260.5)
23-9/16 (598)
12 (305)
(Bolt size : 3/8 (M10))
1-3/4 9/16
(45) (14.5)
Place a leveler on raised tab.
1-7/16 (36.5)
Recommended
A mounting plate
retention spots
(9 spots in all)
7/16
(12)
5-15/16
(150)
11-15/16 (302.5)
15-3/16 (385)
15-3/16 (385)
6-11/16
(170)
unit : inch (mm)
35-1/16 (890)
Keep here the piece cut out
from the unit for piping
Gas pipe end
Liquid pipe end
Drain hose Through the wall
position
hole φ2-9/16 (65)
* The removed pipe port cover can be
kept in the mounting plate pocket.
Removed pipe
port cover
2.
A Mounting plate
Boring a wall hole and installing wall embedded pipe.
• For walls containing metal frame or metal board, be sure to use a wall
embedded pipe and wall cover in the feed-through hole to prevent possible
heat, electrical shock, or fire.
• Be sure to caulk the gaps around the pipes with caulking material to prevent
water leakage.
1) Bore a feed-through hole of φ2-9/16 inch (65mm) in the wall so it has a down
slope toward the outside.
2) Insert a wall pipe into the hole.
3) Insert a wall cover into wall pipe.
4) After completing refrigerant piping, wiring, and drain piping, caulk pipe hole
gap with putty.
3.
Installing inter-unit wiring.
1) Open the front panel and remove the service lid.
2) Pull out the inter-unit wiring from the back of the
indoor unit to the front. It is easier to pull out if
bending up the wire edge in advance.
3) To connect the inter-unit wiring after hooking the unit
onto the A mounting plate, connect the inter-unit
wiring as shown in the figure at right.
Inside
Wall embedded pipe
(Field supply)
Outside
Caulking
φ2-9/16 (65)
Wall hole cover
(Field supply)
Wall embedded pipe
(Field supply)
Hang indoor
unit’s hook here.
Lift the indoor unit slightly
by placing it on packing
or other similar materials.
Inter-unit wiring
When stripping the ends of
inter-unit wiring in advance,
bind right ends of wires with
insulation tape.
Pull down using caution not
to catch the inter-unit wiring.
6
26
Room Air Conditioners H-Series
EDUS04-906_b
4.
Installation Manual
Laying piping and wiring.
• Lay the piping and drain hose according to the
orientation of the piping coming out of the unit, as shown
below.
• Make sure the drain hose is sloped downward.
• Wrap the piping and drain hose together using insulation
tape.
Piping bundle diagram
Inter-unit wiring
Gas pipe
Drain hose
Liquid pipe
Insulation tape
4-1. Right-side, right-back, or right-bottom piping.
• Right-side piping
• Right-back piping
• Right-bottom piping
Cut out the
piping-through hole.
It is recommended
to use the elbow.
Install with a
downward slope.
Cut out the
piping-through hole.
1) Wrap the piping and inter-unit wiring using insulation tape as shown in the piping bundle diagram.
2) Put all the pipes through the through-hole in the wall and hook the indoor unit onto the A mounting plate.
3) Connect the pipes.
4-2. Left-side, left-back, or left-bottom piping.
• Left-side piping
• Left-back piping
• Left-bottom piping
Refrigerant pipe
Drain hose
Cut out the
piping-through hole.
Cut out the
piping-through hole.
Refrigerant pipe
Refrigerant pipe
1) Replace the drain plug and drain hose. (How to replace the drain plug
and drain hose.)
2) Pull in the refrigerant piping and lay it so that it matches the liquid and
gas piping marked on the A mounting plate.
3) Hook the indoor unit onto the A mounting plate.
4) Connect the pipes. If it is difficult to do, remove the front panel first.
5) Wrap the insulation on the piping with insulation tape. If you are not
replacing the drain hose, store it in the location shown below.
When securing the indoor unit with screws
1) Remove the front grille.
2) Secure the indoor unit
with the D indoor unit
fixing screws.
3) Install the front grille.
D 3/16” × 1/2”L (M4 × 12mm)
4-3. Left-back piping.
Drain hose
Inter-unit wiring
A Mounting plate
Caulk this hole with putty
or caulking material.
Bind with plastic tape.
Wrap insulation tape around the
bent portion of refrigerant pipe.
Overlap at least half the width
of the tape with each turn.
7
Room Air Conditioners H-Series
27
Installation Manual
EDUS04-906_b
Indoor Unit Installation
4-4. Wall embedded piping.
Follow the instructions given under
Left-side, left-back, or left-bottom piping .
1) Insert the drain hose to this depth so it won’t be
pulled out of the drain pipe.
Insert drain hose
to this depth so
it won’t be pulled
out of drain pipe.
Inner wall
1-15/16 inch
(50mm)
or more
Drain hose
Vinyl chloride
drain pipe
(VP-30)
Outer wall
WARNING
Do not bundle the power code with a binding band, a twist tie or other method.
This may cause heat, electric shock or fire.
5.
Wiring.
1) Strip the insulation from the wire (3/4 inch (20mm)).
2) Match wire colours with terminal numbers on indoor and outdoor unit’s terminal blocks and firmly screw wires to the
corresponding terminals.
3) Connect the earth wires to the corresponding terminals.
4) Pull the wires to make sure that they are securely connected, and retain the wires with the binding band as shown in the
illustration below.
5) In case of connecting to an adapter system. Run the remote controller cable and attach the S21.
(Refer to 6. Connecting to the HA system.)
6) Shape the wires so that the service lid fits securely, then close service lid.
Terminal block
Electrical component box
Outdoor unit
Binding band
Shape wires so
that the service
lid will fit securely.
When wire length exceeds
32 ft (10m), use AWG 14 wires.
Use the specified wire type.
Indoor
unit
1 23
L1L2
1
2
3
Back
Lock nut
Retain the wires with
the binding band.
Use AWG 16 or AWG 14 wire
for the Interconnecting wires
Conduit
mounting
plate
Conduit
WARNING
1) Do not use tapped wires, strand wires, extension cords, or starburst connections, as they may cause overheating, electrical
shock, or fire.
2) Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the
terminal block.) Doing so may cause electric shock or fire.
3) When carrying out wiring connection, take care not to pull at the conduit.
8
28
Room Air Conditioners H-Series
EDUS04-906_b
6.
Installation Manual
Connecting to the HA system.
1) Remove the front grille. (3 screws)
2) Remove the decelerator assembly parts.
(1 screw)
2-1) Remove the decelerator assembly
part screws. (See Fig. 1)
2-2) Remove the decelerator assembly
part connector. Remove by pressing
on the tabs on the bottom of the
connector.
(See the tab position diagram 1)
3) Remove the electric parts box.
(1 screw, 2 tabs)
3-1) Remove the electric parts box fixing
screw.
3-2) Pull the electric parts box toward
you and discharge the tab 2.
Fig. 1
Location of the tabs
on the electric parts box
Anti-drip cover
fixing screw
Tab 2
Anti-drip cover
Decelerator assembly
part fixing screw
Tab 1
Electric parts box
fixing screw
Buzzer
Position of tabs on the decelerator
assembly part connector
Ta b
4) Remove the electric parts box cover.
(3 tabs) (Refer to Fig. 2)
4-1) Discharge the tab 3.
4-2) Pull up the electric parts box cover
slowly, discharge the tab 4, slide up,
and discharge the tab 5.
5) Insert the connection cord into the HA
connector “S21”.
6) Lay the connection cord as shown in
“Fig. 3”.
7) Replace the electric parts box cover and
electric parts box as they were.
8) Attach the decelerator assembly part
along with the guide rail. (Refer to Fig. 2)
9) Install the front grille.
Fig. 2
Electric parts box cover
Tab 4
Guide rail
Tab 3
Tab 5
Fig. 3
Electric parts box cover
Inside the electric parts box
HA connector
“S21”
To connection cord
9
Room Air Conditioners H-Series
29
Installation Manual
EDUS04-906_b
Indoor Unit Installation
7.
Drain piping.
The drain hose should
be inclined downward.
1) Connect the drain hose, as described right.
No trap is permitted.
Do not put the end
of the hose in water.
3) When drain hose requires extension, obtain an extension hose commercially
available.
Be sure to thermally insulate the indoor section of the extension hose.
Indoor unit
drain hose
f11/16”
(f18mm)
2) Remove the air filters and pour some water into the drain pan to check the water
flows smoothly.
Extension drain hose
4) When connecting a rigid polyvinyl chloride pipe
(nominal diameter 1/2 inch (13mm)) directly to the
drain hose attached to the indoor unit as with
embedded piping work, use any commercially
available drain socket (nominal diameter 1/2 inch
(13mm)) as a joint.
8.
f11/16”
(f18mm)
Heat insulation tube
(Field supply)
Drain hose supplied with
the indoor unit
Commercially available drain
socket
(nominal diameter 1/2 inch
(13mm))
Commercially available rigid
polyvinyl chloride pipe
(nominal diameter 1/2 inch
(13mm))
Improving installation strength.
• We recommend screwing the indoor unit onto a
A mounting plate in order to improve the
installation strength.
1) Remove the front grille.
2) Screw in the indoor unit with D fixing screws.
3) Attach the front grille.
Screw position
Front diagram
Enlarged diagram
A Mounting plate
Piping
Wall
Shape of
rear side of
indoor unit
A Mounting plate
Indoor unit
Screw position
Screw in
D Fixing screw
3/16” × 1/2”L (M4 × 12mm)
10
30
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
Refrigerant Piping Work
1.
Flaring the pipe end.
(Cut exactly at
right angles.)
1) Cut the pipe end with a pipe cutter.
2) Remove burrs with the cut surface facing downward
so that the chips do not enter the pipe.
3) Put the flare nut on the pipe.
4) Flare the pipe.
5) Check that the flaring is properly made.
Remove burrs
Flaring
Set exactly at the position shown below.
A
Die
Flare tool for R410A
Conventional flare tool
Clutch-type
Clutch-type (Rigid-type) Wing-nut type (Imperial-type)
0-0.020 inch (0-0.5mm)
0.039-0.059 inch (1.0-1.5mm) 0.059-0.079 inch (1.5-2.0mm)
A
Check
Flare’s inner
surface must
be flaw-free.
The pipe end must
be evenly flared in
a perfect circle.
Make sure that the
flare nut is fitted.
WARNING
1)
2)
3)
4)
5)
6)
2.
Do not use mineral oil on flared part.
Prevent mineral oil from getting into the system as this would reduce the lifetime of the units.
Never use piping which has been used for previous installations. Only use par ts which are delivered with the unit.
Do never install a drier to this R410A unit in order to guarantee its lifetime.
The drying material may dissolve and damage the system.
Incomplete flaring may cause refrigerant gas leakage.
Refrigerant piping.
CAUTION
1) Use the flare nut fixed to the main unit to prevent aging and deterioration.
2) To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.)
3) Use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.
Align the centers of both flares and tighten the flare nuts 3 or 4 turns by hand. Then tighten them fully with the torque wrenches.
[Apply oil]
Do not apply refrigeration
oil to the outer surface.
[Tighten]
Flare nut tightening torque
Gas side
Liquid side
3/8 inch (9.5mm)
1/4 inch (6.4mm)
Torque wrench
Apply refrigeration oil to the
inner surface of the flare.
Flare nut
24.1-29.4 ft·lbf
(32.7-39.9 N·m)
Spanner
Do not apply refrigeration
oil to the flare nut avoid
tightening with over torque.
10.4-12.7 ft·lbf
(14.2-17.2 N·m)
Piping union
Flare nut
2-1. Caution on piping handling.
1) Protect the open end of the pipe against dust and moisture.
2) All pipe bends should be as gentle as possible. Use a pipe bender for
bending.
Wall
Be sure to
place a cap.
Rain
If no flare cap is
available, cover
the flare mouth
with tape to keep
dirt or water out.
2-2. Selection of copper and heat insulation materials.
• When using commercial copper pipes and fittings, observe the following:
1) Insulation material: Polyethylene foam
Heat transfer rate: 0.041 to 0.052W/mK (0.024 to 0.030 Btu/fth°F (0.035 to 0.045 kcal/mh°C))
Choose heat insulation materials that are designed for HVAC use.
Inter-unit wiring
Gas pipe
Gas pipe insulation
Liquid pipe insulation
Drain hose
Insulation tape
Liquid pipe
2) Be sure to insulate both the gas and liquid piping and to provide insulation dimensions as below.
Gas side
Liquid side
O.D. 3/8 inch (9.5mm)
O.D. 1/4 inch (6.4mm)
Minimum bend radius
1-3/16 inch (30mm) or more
Thickness 0.031 inch (0.8mm) (C1220T-O)
Gas pipe thermal insulation
I.D. 0.472-0.590 inch (12-15mm)
Liquid pipe thermal insulation
I.D. 0.315-0.393 inch (8-10mm)
Thickness 0.393 inch (10mm) Min.
3) Use separate thermal insulation pipes for gas and liquid refrigerant pipes.
11
Room Air Conditioners H-Series
31
Installation Manual
EDUS04-906_b
Trial Operation and Testing
1.
Trial operation and testing.
1-1. Measure the supply voltage and make sure that it falls in the specified range.
1-2. Trial operation should be carried out in either cooling or heating mode.
• In cooling mode, select the lowest programmable temperature; in heating mode, select the highest programmable
temperature.
1) Trial operation may be disabled in either mode depending on the room temperature.
Use the remote controller for trial operation as described below.
2) After trial operation is complete, set the temperature to a normal level (78°F to 82°F (26°C to 28°C) in cooling mode,
68°F to 75°F (20°C to 24°C) in heating mode).
3) For protection, the system disables restart operation for 3 minutes after it is turned off.
1-3. Operate the unit in accordance with the operation manual to check that it operates
normally.
• Even when the air conditioner is not operating, it consumes some electric power. If the customer is not going to use
the unit soon after it is installed, turn off the breaker to avoid wasting electricity.
Trial operation from remote controller
1) Hold the “CLOCK button” for 5 seconds.
(The matrix display will appear on the remote controller.)
2) Display “
” on the matrix display of the remote controller and press the “CLOCK button”.
3) “ ” will be displayed and the unit will enter test run mode.
4) Press the button for test run mode.
• Test run mode will stop automatically after around 30 minutes.
Press the ON/OFF button to force the test-run to stop.
2.
Test items.
Test items
Symptom
(diagnostic display on RC)
Indoor and outdoor units are installed properly on solid bases.
Fall, vibration, noise
Did you install the deodorizing filter for the streamer and the titanium
apatite photocatalytic air-purifying filter?
Noise, water leakage
Have you performed a gas leak test?
Incomplete cooling/heating function
No refrigerant gas leaks.
Incomplete cooling/heating function
Refrigerant gas and liquid pipes and indoor drain hose extension are
thermally insulated.
Water leakage
Draining line is properly installed.
Water leakage
Does the drain hose produce abnormal noise (perking sound) when using
the ventilation fan or others?
Use of separately sold air cut drain plug
System is properly ground to earth.
Electrical leakage
The specified wires are used for inter-unit wiring connections.
Inoperative or burn damage
Indoor or outdoor unit’s air intake or exhaust has clear path of air.
Stop valves are opened.
Incomplete cooling/heating function
Indoor unit properly receives remote controller commands.
Inoperative
Did you check the address setting?
Inoperative
Check
12
3P227261-1
32
Room Air Conditioners H-Series
EDUS04-906_b
11.2
Installation Manual
Outdoor Units
Accessories
Accessories supplied
with the outdoor unit:
(A) Installation manual
1
(C) Binding band
1
(B) Drain plug (Heat pump-Models)
There is on the
bottom packing case.
1
Precautions for Selecting the Location
1) Choose a place strong enough to bear the weight and vibration of the unit, The location should not amplified the unit noise.
2) Choose a location where the hot air discharged from the unit and the operationing noise will not be a nuisance to the neighbors.
3) Avoid noise sensitive locations such as bedrooms to avoid future problems.
4) There must be sufficient clearance for carrying the unit into and out of the site.
5) There must be sufficient space around the air inlet and the air outlet with no obstructions to airflow.
6) The surrounding area must be free from the possibility of flammable gas leakage.
7) Install units, power cords and inter-connecting cables at least 10 feet (3m) away from television and radio
sets. This is to prevent interference to images and sounds. (Noises may be heard even if they are more
than 10 feet (3m) away depending on radio wave conditions.)
8) In coastal areas or other places with salty atmosphere of sulfate gas, corrosion may shorten the life of the air conditioner.
9) Do not place moisture sensitive equipment or articles under the outdoor unit condenstate drain.
NOTE: Do not install unit by hanging from a ceiling or stacking units.
CAUTION
When operating the air conditioner in a outdoor temperature
below, be sure to follow the instructions described below.
1) To prevent exposure to wind, install the outdoor unit with its
suction side facing the wall.
2) Never install the outdoor unit at a site where the suction side
may be exposed directly to wind.
3) To prevent exposure to wind, it is recommended to install a
baffle plate on the air discharge side of the outdoor unit.
4) In heavy snowfall areas, select an installation site where the
snow will not affect the unit.
Room Air Conditioners H-Series
Construct a large canopy.
Construct a pedestal.
Install the unit high enough off the
ground to prevent burying in snow.
33
Installation Manual
EDUS04-906_b
Precautions on Installation
• Ensure the strength and level of the installation will not cause any operating vibration or noise after installed.
• In accordance with the foundation drawing, fix the unit securely by means of the foundation bolts. (Prepare
four sets of 3/8 inch (M10) or 7/16 inch (M12) foundation bolts, nuts and washers each which are available
on the market.)
• It is best to screw in the foundation bolts until their length are 3/4 inch (20mm) from the foundation surface.
3/4” (20mm)
Outdoor Unit Installation Drawings
Max. allowable length
Wrap the insulation pipe with
the finishing tape from bottom
to top.
32ft (10m)
Max. allowable height
26ft (8m)
Gas pipe
O.D. 3/8 inch (9.5mm)
Liquid pipe
O.D. 1/4 inch (6.4mm)
* No refrigerant needs to be added if the piping does not
exceed the maximum length.
Allow space for piping
and electrical servicing.
Allow 11-13/16 inch
(300mm) of work space
below the ceiling surface.
Stop valve cover
How to remove the stop valve cover.
Remove the screw on the
stop valve cover.
Slide the lid downward
to remove it.
9-7/8” (250mm)
from wall
In sites with poor drainage, use
block bases for outdoor unit.
Adjust foot height until the unit
is leveled. Otherwise, water
leakage or pooling of water may
occur.
22-5/8
(574)
(Foot b
olt-hole
centers
)
How to attach the stop valve cover.
Insert the upper part of the
stop valve cover into the
outdoor unit to install.
Tighten the screws.
1) le
(31 ho
/4 bolt1
t
12 (Foo ters)
cen
4-1/8 (1
05.5)
(From
unit’s
side)
Where there is a danger of the unit
falling, use foot bolts, or wires.
Unit: inch (mm)
Installation Guidelines
• Where a wall or other obstacle is in the path of outdoor unit’s intake or exhaust airflow, follow the
installation guidelines below.
• For any of the below installation patterns, the wall height on the exhaust side should be 47-3/16 inch
(1200mm) or less.
Wall facing one side
More than 1-15/16 (50)
More
than
3-15/16
(100)
47-3/16
(1200)
or less
Side view
More than
5-7/8 (150)
More
than
5-7/8
(150)
More than
1-15/16 (50)
34
Walls facing three sides
Walls facing two sides
More than 3-15/16 (100)
More than
1-15/16 (50)
Top view
More than
1-15/16 (50)
More than
11-13/16 (300)
Top view
Unit: inch (mm)
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
Outdoor Unit Installation (1)
1.
Installing outdoor unit.
1) When installing the outdoor unit, refer to “Precautions for Selecting the Location” and the “Outdoor
Unit Installation Drawings”.
2) If drain work is necessary, follow the procedures below.
2.
Drain work (heat pump-models).
1) Use drain plug for drainage.
2) If the drain port is covered by a mounting base or floor surface, place additional
foot bases of at least 1-1/4 inch (30mm) height under the outdoor unit’s feet.
3) In cold areas, do not use a drain hose with the outdoor unit.
(Otherwise, drain water may freeze, impairing heating performance.)
3.
Drain-water hole
Bottom frame
(B) Drain plug
Hose (available commercially,
inner dia. 5/8 inch (16mm))
Flaring the pipe end.
(Cut exactly at
right angles.)
1) Cut the pipe end with a pipe cutter.
2) Remove burrs with the cut surface
facing downward so that the chips do
not enter the pipe.
3) Put the flare nut on the pipe.
4) Flare the pipe.
5) Check that the flaring is properly made.
Remove burrs
Flaring
Set exactly at the position shown below.
A
Die
A
Flare tool for R410A
Conventional flare tool
Clutch-type
Clutch-type (Rigid-type) Wing-nut type (Imperial-type)
0-0.020 inch (0-0.5mm) 0.039-0.059 inch (1.0-1.5mm) 0.059-0.079 inch (1.5-2.0mm)
Check
Flare’s inner
surface must
be flaw-free.
The pipe end must
be evenly flared in
a perfect circle.
Make sure that the
flare nut is fitted.
WARNING
1) Do not use mineral oil on flared part.
2) Prevent mineral oil from getting into the system as this would reduce the lifetime of the units.
3) Never use piping which has been used for previous installations. Only use parts which are delivered with the unit.
4) Do never install a drier to this R410A unit in order to guarantee its lifetime.
5) The drying material may dissolve and damage the system.
6) Incomplete flaring may cause refrigerant gas leakage.
4.
Refrigerant piping.
CAUTION
1) Use the flare nut fixed to the main unit. (To prevent cracking of the flare nut by aged deterioration.)
2) To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil
for R410A.)
3) Use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.
Align the centers of both flares and tighten the flare nuts 3 or 4 turns by hand. Then tighten them fully
with the torque wrenches.
[Apply oil]
Do not apply refrigeration
oil to the outer surface.
[Tighten]
Apply refrigeration oil to the
inner surface of the flare.
Torque wrench
Flare nut
Spanner
Piping union
Do not apply refrigeration oil to the flare
Flare nut
nut avoid tightening with over torque.
Flare nut tightening torque
Valve cap tightening torque
Gas side
Liquid side
Gas side
Liquid side
3/8 inch (9.5mm)
1/4 inch (6.4mm)
3/8 inch (9.5mm)
1/4 inch (6.4mm)
24.1-29.4ft • lbf (32.7-39.9N • m)
10.4-12.7ft • lbf (14.2-17.2N • m)
15.9-20.2ft • lbf (21.6-27.4N • m)
15.9-20.2ft • lbf (21.6-27.4N • m)
Service port cap tightening torque
7.9-10.8ft • lbf (10.8-14.7N • m)
Room Air Conditioners H-Series
35
Installation Manual
EDUS04-906_b
Outdoor Unit Installation (2)
5.
Purging air and checking gas leakage.
• When piping work is completed, it is necessary to purge the air and check for gas leakage.
WARNING
1)
2)
3)
4)
Do not mix any substance other than the specified refrigerant (R410A) into the refrigeration cycle.
When refrigerant gas leaks occur, ventilate the room as soon and as much as possible.
R410A, as well as other refrigerants, should always be recovered and never be released directly into the environment.
Use a vacuum pump for R410A exclusively. Using the same vacuum pump for different refrigerants
may damage the vacuum pump or the unit.
• If using additional refrigerant, perform air purging from the refrigerant
pipes and indoor unit using a vacuum pump, then charge additional
refrigerant.
• Use a hexagonal wrench (3/16 inch (4mm)) to operate the stop valve rod.
• All refrigerant pipe joints should be tightened with a torque wrench at
the specified tightening torque.
Compound
Pressure
pressure gauge meter
Gauge
manifold
Gas stop
valve
Low-pressure
valve
Highpressure
valve
Valve caps
Charging
hoses
Vacuum pump
adapter
Vacuum pump
Service port
Liquid stop valve
1) Connect projection side of charging hose (which comes from gauge manifold) to gas stop valve’s service port.
2) Fully open gauge manifold’s low-pressure valve (Lo) and completely close its high-pressure valve (Hi).
(High-pressure valve subsequently requires no operation.)
3) Do vacuum pumping and make sure that the compound pressure gauge reads – 29.9inHg (–0.1MPa).
(The vacuum pump should run for at least 10 min.)
4) Close gauge manifold’s low-pressure valve (Lo) and stop vacuum pump.
(Keep this state for a few minutes to make sure that the compound pressure gauge pointer does not swing back.)*1.
5) Remove valve caps from liquid stop valve and gas stop valve.
6) Turn the liquid stop valve’s rod 90 degrees counterclockwise with a hexagonal wrench to open valve.
Close it after 5 seconds, and check for gas leakage.
Using soapy water, check for gas leakage from indoor unit’s flare and outdoor unit’s flare and valve rods.
After the check is complete, wipe all soapy water off.
7) Disconnect charging hose from gas stop valve’s service port, then fully open liquid and gas stop valves.
(Do not attempt to turn valve rod beyond its stop.)
8) Tighten valve caps and service port cap for the liquid and gas stop valves with a torque wrench at the specified
torques.
*1. If the compound pressure gauge pointer swings back, refrigerant may have water content or a loose pipe
joint may exists. Check all pipe joints and retighten nuts as needed, then repeat steps 2) through 4).
36
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
Outdoor Unit Installation (3)
6.
Refilling the refrigerant.
Check the type of refrigerant to be used on the machine nameplate.
Precautions when adding R410A
Fill from the liquid pipe in liquid form.
It is a mixed refrigerant, so adding it in gas form may cause the
refrigerant composition to change, preventing normal operation.
1) Before filling, check whether the cylinder has a siphon attached or not.
(It should have something like “liquid filling siphon attached” displayed on it.)
Filling a cylinder with an
attached siphon
Filling other cylinders
Stand the cylinder upright
when filling.
Turn the cylinder
upside-down when filling.
There is a siphon pipe
inside, so the cylinder
need not be upsidedown to fill with liquid.
• Be sure to use the R410A tools to ensure pressure and to prevent foreign objects entering.
7.
Refrigerant piping work.
1) Protect the open end of the pipe against dust and moisture.
2) All pipe bends should be as gentle as possible. Use a pipe bender for bending.
7-2
Wall
Be sure to
place a cap.
7-1 Cautions on pipe handling.
Rain
If no flare cap is
available, cover the
flare mouth with
tape to keep dirt or
water out.
Selection of copper and heat insulation materials.
When using commercial copper pipes and fittings, observe the following:
1) Insulation material: Polyethylene foam
Heat transfer rate: 0.041 to 0.052W/mK (0.024-0.030Btu/fth°F (0.035-0.045kcal/mh°C))
Refrigerant gas pipe’s surface temperature reaches 230°F (110°C) max.
Choose heat insulation materials that will withstand this temperature.
2) Be sure to insulate both the gas and liquid piping and to provide insulation dimensions as below.
Piping bundle diagram
Seal the edge of the insulation if
there is a possibility that the
condensation from the shut-off
valve might drip onto the indoor
unit through the gap between the
insulation and the pipe.
Gas side
Liquid side
Gas pipe thermal
insulation
Finishing tape
Inter-unit wiring
Gas pipe
Drain hose
Gas pipe
insulation
Liquid pipe
thermal insulation
Liquid pipe insulation
Liquid pipe
O.D. 3/8inch (9.5mm) O.D. 1/4inch (6.4mm) I.D. 0.472-0.590inch (12-15mm) I.D. 0.315-0.393inch (8-10mm)
Minimum bend radius
1-3/16inch (30mm) or more
Thickness 0.393inch (10mm) Min.
Thickness 0.031inch (0.8mm) (C1220T-O)
3) Use separate thermal insulation pipes for gas and liquid refrigerant pipes.
Pump Down Operation
In order to protect the environment, be sure to pump down when relocating or disposing of the unit.
1) Remove the valve caps from liquid stop valve and gas stop valve.
2) Carry out forced cooling operation.
3) After 5 to 10 minutes, close the liquid stop valve with a
hexagonal wrench.
4) After 2 to 3 minutes, close the gas stop valve and stop
forced cooling operation.
Gas stop valve
Close
Hexagonal
wrench
Valve cap
How to force cooling operation mode
Using the indoor unit operation/stop button
Press the indoor unit operation/stop button for at least 5 seconds. (Operation will start.)
• Forced cooling operation will stop automatically after around 15 minutes.
To force a test run to stop, press the indoor unit operation/stop button.
Liquid stop valve
CAUTION
After closing the liquid stop valve, close the gas stop valve within 3 minutes, then stop the forced operation.
Room Air Conditioners H-Series
37
Installation Manual
EDUS04-906_b
Wiring (1)
WARNING
1) Do not use spliced wires, stranded wires, extension cords, or starburst connections, as they may cause
overheating, electrical shock, or fire. Follow all Local, and State electrical codes.
2) Do not use locally purchased electrical parts inside the product. (Do not overload the circuit by adding
drain pump or other electrical equipment to unit terminals.) Doing so may cause electric shock or fire.
3) Be sure to install an earth leak detector. (One that can handle higher harmonics.)
(This unit uses an inverter, which means that it must be used an earth leak detector capable handling
harmonics in order to prevent malfunctioning of the earth leak detector itself.)
4) Use an all-pole disconnection type breaker with at least 1/8 inch (3mm) between the contact point gaps.
5) The earth leakage circuit breaker must operate at 30mA or lower.
6) When carrying out wiring connection, take care not to pull at the conduit.
<Work before wiring>
A protection plate is fixed for protection from the high-voltage section.
Before starting wiring work, remove the 2 screws and the protection plate.
<Method of mounting conduit>
1) Pass wires through the conduit and secure them with a lock nut.
2) By removing the 2 screws to remove the conduit mounting plate, you can work without the plate.
3) Secure the wire with a binding band to the conduit mounting plate.
After completing the work, reattach the conduit mounting plate to its original position.
Power supply
terminal block
1
2
Protection plate
3
Screw
Use the specified wires
and connect them
securely.
Shape the wires so that
there is no lifting of the
stop valve cover or
other structural parts.
Secure the wires
firmly using the
binding band, as
(C) Binding shown in the figure.
Secure firmly,
band
making sure no
outside pressure is
exerted on the
terminals.
Conduit
mounting
plate
WARNING
When the protection plate is removed,
do not turn ON the safety breaker.
Lock nut
Conduit
• Do not turn ON the safety breaker until all work is completed.
When wire length exceeds
<Wiring procedure>
32ft (10m), use AWG14 wires.
1) Strip the insulation from the wire (3/4 inch (20mm)).
1
Indoor 2
2) Connect the connection wires between the
3
unit
indoor and outdoor units so that the terminal
numbers match.
Outdoor unit
1 23
Use AWG16 or AWG14
wire for the power supply
and interconnecting wires.
L1 L2
Safety
breaker
15A
Earth leakage
circuit breaker
Power supply
60Hz 208-230V
Earth
3) After completing wiring, fix the protection plate to its original position.
38
Room Air Conditioners H-Series
EDUS04-906_b
Installation Manual
Wiring (2)
CAUTION (1)
In case using stranded wires is unavoidable for some reason,
make sure to install the round crimp-style terminals on the tip.
Round
crimp-style
terminal
Stranded
wire
Place the round crimp-style terminals on the wires up to the
covered part and secure in place.
Screw
<Ground terminal installation>
1) Use the following method when installing a single core wire.
Flat washer
A single core wire
Arrow view
2) Use the following method when installing the round crimp-style terminal.
Flat washer
Screw
Screw
Screw
Round crimpstyle terminal
Flat washer
Round crimpstyle terminal
Flat washer
Round
crimp-style
terminal
Good
Wrong
Arrow view
CAUTION (2)
When connecting the connection wires to the terminal
board using a single core wire, be sure to perform curling.
Problems with the work may cause heat and fires.
3) Pull the wire and make sure that it does not disconnect. Then fix the wire in place with a wire stop.
Test Run and Final Check
1.
Trial operation and testing.
• Measure the supply voltage and make sure that it falls in the specified range.
• See “Test Run and Final Check” in the installation manual that came with the indoor unit for details on how to
perform the test run and what to check for.
2.
Test items.
Symptom
(diagnostic display on RC)
Test items
Outdoor unit is installed properly on a solid base.
Fall, vibration, noise
No refrigerant gas leaks.
Incomplete cooling/heating function
Refrigerant gas and liquid pipes and indoor drain
hose extension are thermally insulated.
Water leakage
Draining line is properly installed.
Water leakage
Contact and check with the user whether the
outdoor unit requires drainage work.
Drainage instillation from the bottom
hole of the outdoor unit.
System is properly ground to earth.
Electrical leakage
The specified wires are used for interconnecting
wire connections.
Inoperative or burn damage
Outdoor unit’s air intake or exhaust has clear path of air.
Stop valves are opened.
Incomplete cooling/heating function
Check
3P226011-1
Room Air Conditioners H-Series
39
Operation Manual
EDUS04-906_b
12. Operation Manual
Read these SAFETY CONSIDERATIONS for Operations
carefully before operating an air conditioner or heat pump.
Make sure that the unit operates properly during the startup
operation. Instruct the customer on how to operate and
maintain the unit.
Inform customers that they should store this Operation
Manual with the Installation Manual for future reference.
Meanings of DANGER, WARNING, CAUTION, and NOTE
Symbols:
with plastic bags face the danger of death by
suffocation.
• Contact your dealer for repair and maintenance.
Improper repair and maintenance may result in water
leakage, electric shock, and fire. Only use
accessories made by Daikin that are specifically
designed for use with the equipment and have them
installed by a professional.
DANGER .............. Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING ............ Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
• Contact your dealer to move and reinstall the air
conditioner or heat pump. Incomplete installation may
result in water leakage, electric shock, and fire.
CAUTION ............. Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
NOTE .................. Indicates situations that may result in
equipment or property-damage
accidents only.
• Never use flammable spray such as hair spray,
lacquer, or paint near the unit. Flammable spray may
cause a fire.
• Do not install the unit in an area where flammable
materials are present due to risk of explosion
resulting in serious injury or death.
• Any abnormalities in the operation of the air
conditioner or heat pump, such as smoke or fire,
could result in severe injury or death. Turn off the
power and contact your dealer immediately.
• Refrigerant gas may produce toxic gas if it comes into
contact with fire, such as from a fan, heater, stove, or
cooking device. Exposure to this gas could cause
severe injury or death.
• For refrigerant leakage, consult your dealer.
Refrigerant gas is heavier than air and replaces
oxygen. A massive leak could lead to oxygen
depletion, especially in basements, and an
asphyxiation hazard could occur leading to serious
injury or death.
• If equipment utilizing a burner is used in the same
room as the air conditioner or heat pump, there is the
danger of oxygen deficiency which could lead to an
asphyxiation hazard resulting in serious injury or
death. Be sure to ventilate the room sufficiently to
avoid this hazard.
• Safely dispose of the packing materials. Packing
materials, such as nails and other metal or wooden
parts, may cause stabs or other injuries.
• Never let the indoor unit or the remote controller get
wet. Water can cause an electric shock or a fire.
• When a fuse blows out, never replace it with one of
incorrect ampere ratings or different wires. Always
replace any blown fuse with a fuse of the same
specification.
• Never remove the fan guard of the unit. A fan rotating
at high speed without the fan guard is very
dangerous.
• Never inspect or service the unit by yourself. Contact
a qualified service person to perform this work.
• Turn off all electrical power before doing any
maintenance to avoid the risk of serious electric
shock; never sprinkle or spill water or liquids on the
unit.
• Do not touch the switch with wet fingers. Touching a
switch with wet fingers can cause electric shock.
• Do not allow children to play on or around the unit to
prevent injury.
• The heat exchanger fins are sharp enough to cut. To
avoid injury wear gloves or cover the fins while
working around them.
• Do not put a finger or other objects into the air inlet or
air outlet. The fan is rotating at high speed and will
cause injury.
• Check the unit foundation for damage on a
continuous basis, especially if it has been in use for a
long time. If left in a damaged condition the unit may
fall and cause injury.
• Tear apart and throw away plastic packaging bags so
that children will not play with them. Children playing
40
Room Air Conditioners H-Series
EDUS04-906_b
• Placing a flower vase or other containers with water or
other liquids on the unit could cause a shock or fire if
a spill occurs.
• Do not touch the air outlet or horizontal blades while
the swing flap is in operation because fingers could
get caught and injured.
• Never touch the internal parts of the controller. Do not
remove the front panel because some parts inside are
dangerous to touch. To check and adjust internal
parts, contact your dealer.
• Do not use the air conditioner or heat pump for any
other purposes other than comfort cooling or heating.
Do not use the unit for cooling precision instruments,
food, plants, animals or works of art.
• Do not place items under the indoor unit as they may
be damaged by condensates that may form if the
humidity is above 80% or if the drain outlet gets
blocked.
• Before cleaning, stop the operation of the unit by
turning the power off or by pulling the supply cord out
from its receptacle. Otherwise, an electric shock and
injury may result.
• Do not wash the air conditioner or heat pump with
excessive water. An electric shock or fire may result.
• Avoid placing the controller in a spot splashed with
water. Water entering the controller may cause an
electric shock or damage the internal electronic parts.
• Do not operate the air conditioner or heat pump when
using a room-fumigation type of insecticide. Failure to
observe this could cause the chemicals to be
deposited in the unit and can endanger the health of
those who are hypersensitive to chemicals.
• Do not turn off the power immediately after stopping
operation. Always wait for at least five minutes before
turning off the power. Otherwise, water leakage may
occur.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• The remote controller should be kept away from
children so they cannot play with it.
• Consult with the installation contractor for cleaning.
• Incorrect cleaning of the inside of the air conditioner
or heat pump could make the plastics parts break and
cause water leakage or electric shock.
• Do not touch the air inlet or aluminum fin of the air
conditioner or heat pump as they can cut and cause
injury.
Room Air Conditioners H-Series
Operation Manual
• Do not place objects in direct proximity of the outside
unit. Do not let leaves and other debris accumulate
around the unit. Leaves are a hotbed for small animals
which can enter the unit. Once inside the unit, animals
can cause the unit to malfunction, and cause smoke
or fire when they make contact with electrical parts.
• Never press the button of the remote controller with a
hard, pointed object. The remote controller may be
damaged.
• Never pull or twist the electric wire of the remote
controller. It may cause the unit to malfunction.
• Do not place appliances that produce open flames in
places that are exposed to the air flow of the unit or
under the indoor unit. It may cause incomplete
combustion or deformation of the unit due to the heat.
• Do not expose the controller to direct sunlight. The
LCD display can become discolored and may fail to
display the data.
• Do not wipe the controller operation panel with
benzene, thinner, chemical dust cloth, etc. The panel
may get discolored or the coating can peel off. If it is
heavily dirty, soak a cloth in water-diluted neutral
detergent, squeeze it well and wipe the panel clean.
Then wipe it with another dry cloth.
• Dismantling of the unit, disposal of the refrigerant, oil,
and additional parts, should be done in accordance
with the relevant local, state, and national regulations.
• Operate the air conditioner or heat pump in a
sufficiently ventilated area and not surrounded by
obstacles. Do not use the air conditioner or heat pump
in the following places.
a. Places with a mist of mineral oil, such as cutting oil.
b. Locations such as coastal areas where there is a lot
of salt in the air.
c. Locations such as hot springs where there is a lot of
sulfur in the air.
d. Locations such as factories where the power voltage
varies a lot.
e. In cars, boats, and other vehicles.
f. Locations such as kitchens where oil may splatter or
where there is steam in the air.
g. Locations where equipment produces
electromagnetic waves.
h. Places with an acid or alkaline mist.
i. Places where fallen leaves can accumulate or where
weeds can grow.
• Take snow protection measures. Contact your dealer
for the details of snow protection measures, such as
the use of a snow protection hood.
• Do not attempt to do electrical work or grounding
work unless you are licensed to do so. Consult with
your dealer for electrical work and grounding work.
41
Operation Manual
EDUS04-906_b
• Pay Attention to Operating Sound. Be sure to use the
following places:
a. Places that can sufficiently withstand the weight of
the air conditioner or heat pump yet can suppress
the operating sound and vibration.
b. Places where warm air from the air outlet of the
outside unit or the operating sound of the outside
unit does not annoy neighbors.
• Make sure that there are no obstacles close to the
outside unit. Obstacles close to the outside unit may
drop the performance of the outside unit or increase
the operating sound of the outside unit.
• Consult your dealer if the air conditioner or heat pump
in operation generates unusual noise.
• Make sure that the drainpipe is installed properly to
drain water. If no water is discharged from the
drainpipe while the air conditioner or heat pump is in
the cooling mode, the drainpipe may be clogged with
dust or dirt and water leakage from the indoor unit
may occur. Stop operating the air conditioner or heat
pump and contact your dealer.
42
Room Air Conditioners H-Series
EDUS04-906_b
Operation Manual
QUATERNITY DRYING / DRY COOLING...................YELLOW
The lamp color also changes according to the optional
function
Room Air Conditioners H-Series
43
Operation Manual
EDUS04-906_b
Ground terminal
44
Room Air Conditioners H-Series
EDUS04-906_b
Operation Manual
DRY button
Room Air Conditioners H-Series
45
Operation Manual
46
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
47
Operation Manual
48
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Operation Manual
COOLING • DRY Operation
“DRY COOLING” Operation
DRY operation
Hi
Std
Lo
Constant
Note on “Dry Cooling” operation
“DRY COOLING” may raise humidity temporarily.
Note on Dry Operation
The operation mode change from COOLING to DRY may raise humidity temporarily.
Room Air Conditioners H-Series
49
Operation Manual
50
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
51
Operation Manual
52
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Operation Manual
COOLING or “DRY COOLING” operation, the
A) FLASH STEAMER AIR PURIFYING
individual operation
B) “DRY COOLING” • COOLING
C) HEATING
Room Air Conditioners H-Series
53
Operation Manual
EDUS04-906_b
COOLING BREEZE operation is for COOLING, “DRY COOLING” AND FLASH STREAMER,
AIR PURIFYING operation.
54
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
55
Operation Manual
EDUS04-906_b
-1.8°F (-1°C)
-3.6°F (-2°C)
56
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
57
Operation Manual
EDUS04-906_b
COOLING or “DRY COOLING” mode or
58
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
59
Operation Manual
60
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
61
Operation Manual
62
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
63
Operation Manual
64
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
65
Operation Manual
66
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
67
Operation Manual
68
EDUS04-906_b
Room Air Conditioners H-Series
EDUS04-906_b
Room Air Conditioners H-Series
Operation Manual
69
Operation Manual
EDUS04-906_b
3P226009-1
70
Room Air Conditioners H-Series
EDUS04-906_b
Optional Accessories
13. Optional Accessories
13.1
Option List
13.1.1 Indoor Units
Option Name
FTXG09/12/15HVJU
1
Centralized Control Board-Up to 5 Rooms 1
2
Wiring Adapter for Time Clock / Remote Control 2
(Normal Open Pulse Contact / Normal Open Contact)
3
Central Remote Controller (Fahrenheit) 1
4
Central Remote Controller (Celsius) 1
5
Unified ON/OFF Controller 1
DCS301C71
6
Schedule Timer Controller 1
DST301BA61
7
Interface Adapter for Room Air Conditioner
KRP928B2S
8
Titanium Apatite Photocatalytic
Air-purifying & Deodorizing Filter Set 3
KAF974B42S
9
The Remote Controller Loss Prevention with the Chain
KRC72
KRP413A1S
DCS302C71
DCS302CA61
KKF936A4
Note:
1 Wiring adapter is also required for each indoor unit.
2 Time clock and other devices ; obtained locally.
3 Standard accessory
13.1.2 Outdoor Units
Option Name
RXG09/12/15HVJU
1
Drain Plug
KKP937A4
2
Air Direction Adjustment Grille
KPW937A4
Room Air Conditioners H-Series
71
Optional Accessories
13.2
EDUS04-906_b
Installation Manual
13.2.1 KRP413A1S
Safety Precautions
Read these safety precautions carefully before installing the unit, and be
sure to install the unit properly.
This manual classifies precautions to the user into the following two
categories. These warnings and cautions are for your safety. Follow them.
WARNING
Faulty installation can result in death or serious injury
CAUTION
Faulty installation can result in serious injury
or other serious consequences.
Below is a key to symbols used in this manual.
Be sure to follow instructions.
Be sure to perform grounding work.
Never attempt.
After installation is complete, test the unit to confirm that it is working
properly, and instruct the owner its proper use.
WARNING
Installation should be left to the dealer from whom you purchased the unit, or
another qualified professionals.
Install the unit securely according to the installation manual. Faulty installation
may lead to electric shock or fire.
Be sure to use the supplied or specified parts. Using other parts may lead to
electric shock or fire.
Install the unit securely in a location that will support its weight. If installed in a
poor location or improperly installed, the unit may not work as intended.
For electrical work, follow local electric standards and the installation manual.
Faulty installation may lead to fire or electric shock.
Do not bundle the power cord, or attempt to extend it by splicing it with another
cord or by using an extension cord. Do not place any other load on the power
circuit used for the unit. Improper wiring may lead to electric shock, heat
generation or fire.
Use dedicated wiring for all electrical connections, and be sure to arrange the
wiring so that force applied to the wiring will not damage the terminals. Poor
wiring or installation may cause electric shock, heat generation or fire.
1. Functions and Features
On/Off setting
Switching between Instantaneous Contact/Normal Contact
Connection with five-room central controller (KRC72 for oversea model)
Connection with fan coil remote controller
Automatic reset after power failure
Output of normal operation signals/malfunction signals
2. Field Wiring
For interconnecting wiring, use Daikin KDC100A12 cable (not supplied) or
other similar cable. The cable should have the specifications shown below.
Optional cable KDC100A12 (without connectors)
Specifications:
0.2 mm2 × 4 conductor (sheathed)
Outer diameter: φ 5.3
Length:
328 ft (100 m)
Color:
Grey
Other cable (commercially available)
Outer dia.
Remarks
Cable for instrumentation (IPVV) 0.3 mm 2 × 4-conductor
Item
7.2 mm
Hard sheath
Microphone cord (MVVS) 0.3 mm2 × 4-conductor
8.0 mm
Microphone cord (MVVS) 0.2 mm2 × 4-conductor
6.5 mm
Microphone cord (MVVS) 0.15 mm2 × 4-conductor
4.8 mm
Shielded
Intercom cable 0.65 mm2 dia. × 4-conductor
PVC jumper wire (TJVC) (from 0.5 mm dia. × 4 pcs.)
—
Not sheathed
Note 1: Keep any wiring for the control unit away from the power cord to prevent
electrical noise.
Note 2: Do not use cables shown above for power cord, inter-unit cord/cable or
power cord for lamps.
CAUTION
Before installation, unplug the air conditioner to ensure safety. Failure to do so
may cause electric shock.
Static electricity may damage electric components. Before connecting cables
and communication lines, and operating the switches, be sure to discharge any
electrical charge from your body (by, for example, touching the ground line)
Do not install the unit in a location where it may be exposed to flammable
gases. If gas leaks and build up around the unit, it may catch fire.
Do not place the wiring close to the power cord, inter-unit cable, or pipes which
generate noise. Treat the wiring with care.
72
Room Air Conditioners H-Series
EDUS04-906_b
Optional Accessories
Installation
This product is available in two types. The KRP413A1S · KRP413AA1S is for installation in a case independent of the indoor unit, and
the KRP413A1 is for installation within the indoor unit.
1. KRP413A1S · KRP413AA1S
1
3. Attaching Adaptor Case Assy (for KRP413A1S · KRP413AA1S)
Installation diagram
1
Adaptor case
Indoor unit PCB
Using the screws (to mount on a wall, etc.)
Use the 3 supplied screws to attach the case assy .
Adaptor case
S21
Indoor unit
wiring
2
Local wiring or
power cord, etc.
Install the adaptor case assy as close to the indoor unit as possible.
Removing case front
Case front
Components
Adaptor case assy
(Adaptor (PCB) is attached in the adaptor case.)
Wiring (approx. 0.8 m)
Screw
Adaptor PCB
Screw cover
Accessories
• Binding band (4 pcs.)
• Securing tape for attaching to the indoor unit (2 sets)
• Screws for attaching the adaptor case (4 pcs.)
• Screws for attaching to the wall (3 pcs.)
Remove the screw cover, one of the screws
and then the case front.
Attach the case back to the surface by
tightening the screws through the screw
holes (one round hole, two long holes).
After connecting the cables (refer to the following sections), replace the
case front. Be careful not to damage the wiring in the case.
Press in so that the prong catches
the case back.
Installation manual
Wiring
2. KRP413A1
For this type, install the adaptor PCB within the indoor unit. The method of
installation and connection vary depending on the model of the air
conditioner. See your air conditioner installation manual for details.
1
Screw
Screw cover
Components
Adaptor PCB
Installation manual
Wiring (approx. 0.25 m)
2
Using securing tape (to attach on the indoor unit)
Attach the adaptor case with the supplied securing tape.
Remove the case front (as for mounting on a wall).
After connecting the cables (see the following sections), replace the
case front. It can be screwed to the case back from the rear with the
four supplied screws.
Be careful not to damage the wiring in the case.
Attach the hook side (loop side) of the included securing tape to the rear
surface of the HA case, then attach the loop side (hook side) to the top of
the air conditioner unit spaced at the same intervals.
Securing tape
Hook side (loop side)
Securing tape
Loop side (hook side)
Indoor unit
To prevent the adaptor case assy from falling, do not use the securing
tape for attaching it to a wall or other surface.
Room Air Conditioners H-Series
73
Optional Accessories
EDUS04-906_b
Wiring
1. Wiring
4. Connection with Remote Controller
 Connect one end of the wiring to connector S21 of the PCB in the
indoor unit.
 Connect the other end of the wiring to connector S6 of the adaptor
PCB.
 Connect field wiring according to the functions assigned to each
connection terminal of the adaptor PCB.
 Secure all wires.
1
Example connections with three kinds of remote controllers are shown
bellow.
Note: These connections cannot be used in combination.
1
Generic remote controller
 Set SW1-1 to Off and select Operation Mode 1.
SW1
Securing wires in the adaptor case assy (for KRP413A1S · KRP413AA1S)
ON
OFF
 Fasten with a tie-wrap so that wires will not come loose even if pulled.
If the wire protrudes from
this side, cut the cut-off
section of the case front.
1
2
<Instantaneous Contact>
1
On/Off
2
1
Off
Inter unit
cable (field wiring)
Tie-wrap
(to prevent the wires from coming loose)
2
2
2. Automatic Reset After Power Failure
1
2
1
On
2
 This PCB stores the following data in the event of a power failure
(common features).
 On/Off (see Note 1)  Operation modes  Temperature setting
 Air flow rate  On/Off status of remote controller
 Power On/Off cannot be controlled
from the unit’s remote controller.
 When power is restored after a
power failure in this mode, On or
Off is determined according to
the current settings of the remote
controller.
Operation
Securing wires in the indoor unit (for KRP413A1)
2
S
1
S
2
Five-room central controller (KRC72)
 Set SW1-1 to Off and select Operation Mode 1.
 The remote controller most recently used takes precedence.
SW1
ON
Five-room central
controller
(Note 1 When SW1-2 is in Off mode, the unit will not be activated.)
OFF
1
4
3. Monitor Signal Output (normal operation and malfunction)
Terminal
blocks A to E
 Maximum length of the wiring is 100 m.
2
1 S
2 4
3
2
1 S
2 1
1
Monitor signal output for LED
Locally procured parts
1
R
D
LED
2
Item Manufacturer
S
4
Max 100 m
2
S
2
<Normal Contact>
 The method for securing wire varies depending on the model of the air
conditioner. See your air conditioner installation manual for details.
1
 The remote controller most
recently used (local or air
conditioner) takes precedence.
 Use a remote controller with a
pulse width of 100 msec or
more.
S
1
LED
Toshiba
D
Rohm
R
Type
TLG208 (green)
TLR208 (red)
1S2473
510 ohm 1/4W
Monitor signal output (normal operation and
malfunction)using external relay contacts
3
Fan coil remote controller
 Set SW1-1 to On and select Operation Mode 2.
 Most settings (power On/Off, air flow rate, mode change) cannot be
made using the air conditioner’s remote controller.
 When power is restored after a power failure in this mode, On or Off is
determined according to the current settings of the remote controller.
 When the Cooling /Heating mode is changed, use the air conditioner’s
remote controller to adjust the temperature.
SW1
ON
S
8
DC12V
–
1
S
5
L1
+
2
3
L2
OFF
: Operation light
: Malfunction light
1
2
1
S
1
H M L OFF
(+)
MR1
(–)
L1
MR1
MR2
(–)
MR2
External power
supply for light
2
L2
1
2
Max 100 m
Field supplied parts
Field procured parts (Recommended external relay contacts)
Manufacturer
74
Type
Coil rated voltage
Fan coil remote controller
On (When heating)
Coil resistance
Omron
MY relay
12 V DC
160 ohm ± 10%
Matsushita
HC relay
12 V DC
160 ohm ± 10%
S
2
1 S
2 3
Off
(When cooling)
Cooling/heating switch
Room Air Conditioners H-Series
EDUS04-906_b
Optional Accessories
Test Operation and Confirmation
1. When the System is Not Working
Is the air conditioner working properly?
Are the connectors of the wiring properly connected?
Are the remote controller and field wiring properly connected?
Are all switch settings correct?
If there is nothing apparently wrong, conduct a diagnostic check using the following procedure.
Diagnostic check
 Defect in adaptor PCB.
 Defect in wiring.
 Defect in indoor unit’s PCB.
 Transmission error (between remote controller and indoor unit)
START
Is the “CPU Normal” light
for the remote controller’s
PCB flashing?
No
Yes
Is 12 V DC being supplied
to No. 4 and No. 5 on S6 of the
remote controller’s PCB?
No
Yes

Is 12 V DC being supplied
to No. 4 and No. 5 on S21
of the indoor unit?
No
Yes

Is the malfunction light
of the remote
controller’s PCB on?

No
Yes

 OR 
2. Switch Settings and Connection Terminals
1
2
1
2
1
2
1
2
S
4
S
1
S
2
S
3
SW1-1
Selecting the operation
mode
SW1-2
Selecting On/Off when
power is restored after
a power failure
S 1
8 2
1
S 2
5
3
S6
SW1-1: OFF
(Operation mode 1)
Operation mode 2 (Used with fan coil remote controller settings)
OFF
Always Off
ON
Off if operation was in Off mode before power failure; On if operation was in
On mode before power failure
Normal contact
S1 (1) - S2 (1)
OPEN
CLOSE
S1 (1) - S1 (2)
Pulse input
On/Off switching
OPEN, Not activated
CLOSE, Activated
S1
S2 (2), S3
S2
S1, S2 OPEN
S3
S1 (1) - S1 (2) CLOSE
On, airflow: L tap
S1 (1) - S2 (1) CLOSE
On, airflow: M tap
S1 (1) - S2 (2) CLOSE
On, airflow: H tap
S3 (With the remote
controller only)
CLOSE, Heating
SW1-1: ON
(Operation mode 2)
CPU normal operation monitor
(Flashes when the operation is normal.)
Operation mode 1 (Used with the exception of fan coil remote controller settings)
Instantaneous contact
SW1
1
2
OFF ON
OFF
ON
S4
S5
Not activated
OPEN, Cooling
(1) - (2)
Voltage on (DC12 V), normal operation light output
(1) - (2)
Normal operation light output (power for light required)
(1) - (3)
Malfunction light output (power for light required)
S6 connector
S8
Not used
(+) - (–)
Connect with connector S21 on the PCB of the indoor unit
Relay DC 12 V power supply terminal (Field supplied parts)
2P031616-1B
Room Air Conditioners H-Series
75
Optional Accessories
EDUS04-906_b
13.2.2 KRP928B2S
1.Overview, Features and Compatible Models
Safety Precautions
This kit is the interface required when connecting the central controller and a Daikin Room Air
Conditioner. Use of the central controller makes it possible to perform the following monitoring
and operations. It is compatible with room air conditioners which have an HA connector S21.
Read these Safety Precautions carefully to ensure correct installation.
This manual classifies precautions into WARNING and CAUTION.
1.Run / stop for the central controller and wired remote controller, operating mode
selection, and temperature can be set.
2.The operating status, any errors, and the content of those errors can be monitored
from the central controller and wired remote controller.
3.Run / stop for the central controller and wireless remote controller, operating mode
selection, and the temperature setting can be limited by the central controller.
4.Zone control can be performed from the central controller.
5.The unit can remember the operating status of the air conditioner before a power
outage and then start operating in the same status when the power comes back
on.
6.Card keys, operating control panels, and other constant / instantaneous
connection-compatible equipment can be connected.
7.The Operating / error signals can be read.
8.HA JEM-A-compatible equipment can be connected.
9.The indoor temperature can be monitored from the Ve-up controller.
WARNING : Failure to follow WARNING is very likely to result in such grave
consequences as death or serious injury.
CAUTION : Failure to follow CAUTION may result in serious injury or
property damage, and in certain circumstances, may result in
a grave consequence.
Be sure to follow all the precautions below ; they are all important for
ensuring safety.
WARNING
 Installation should be left to the dealer or another qualified professional.
Improper installation by yourself may cause malfunction, electrical shock, or fire.
 Install the set according to the instructions given in this manual.
Incomplete or improper installation may cause malfunction, electrical shock, or fire.
Precaution
1.When reading the Operating / error signals, a separate external power source
(DC 12V) is needed.
2.A separate timer power source (DC 16V) is needed when using the schedule
timer independently, and not in conjunction with other central controllers.
3.The range of temperatures that can be set from the central controller is 18°C to
32°C in cooling and 14°C to 28°C in heating.
4.Fan operation cannot be selected from the central controller or wired remote controller.
5.Group control (i.e., control of multiple indoor units with a single remote controller) is
not available.
6.Monitoring is not available of the thermo status, compressor operating status,
indoor fan operating status, electric heater, or humidifier operating status.
7.Forced thermo off, filter sign display and reset, fan direction and speed settings,
air conditioning fee management, energy savings instructions, low-noise
instructions, and demand instructions cannot be made.
 Be sure to use the standard attachments or the genuine parts.
Use of other parts may cause malfunction, electrical shock, or fire.
 Disconnect power to the connected equipment before starting installation.
Failure to do so may cause malfunction, electrical shock, or fire.
CAUTION
 An earth leakage circuit breaker should be installed.
If the breaker is not installed, electrical shock may occur.
 Do not install the set in a location where there is danger of exposure to
inflammable gas.
Gas accumulated around the unit at the worst may cause fire.
2.Component Parts and Separately-Sold Parts which are Required
 To prevent damage due to electrostatic discharge, touch your hand to a
nearby metal object (doorknob, aluminum sash, etc.) to discharge static
electricity from your body before touching this kit.
This kit includes the following components. Check to ensure that none of
these are missing.
Static electricity can damage this kit.
Q’ty
Parts
Kit assy
PCB is in the housing.
 Lay this cable separately from other power cables to avoid external
electrical noises.
After installation is complete, test the operation of the PCB set to check
for problems, and explain how to use the set to the end-user.
1
Screw cover
Parts
Q’ty
Connection harness (about 1.6m)
1set
Mounting screws
3pcs.
Binding band
1pc.
Installation manual
1set
3.Names of Parts and Electric Wiring
<Wiring procedure>
Lower group number
switch (SW1)
Room air conditioner indoor unit
Service monitor (LED1: green)
When the CPU is working
properly, the LED flashes.
Upper group number
switch (SW2-1to 3)
Operation when recovering
from a power outage mode
switch (SW2-4)
Japanese unit / Overseas unit
Setting switch (SW3-3)
DAIKIN
1234
0
OFF
SW1
SW2
LED1
Supplied connection harness
SW3
S6
Tes1
S1
S16
Cable available field supply
(See the installation manual of
the central remote controller)
F1
S8
76
S5
Forced stop
Settings switch (SW3-1)
Power supply terminal (S8)
Connect an external DC 12V power
supply only when reading the
Operating / error display.
S19
F2
A cable field supply
Non polarity
Included in the Drain
Up Kit.
OFF
Once the switches are set and
the wiring complete, secure the
case using the included
screws.
Momentary contact / constant contact
Selection switch (SW3-2)
1 2 3 4 ON
ON
1 1234
To HA connector (S21)
A cable field supply
Separately sold remote control code (quadplex)
KRCW101A Series
Central controller equipment
 DCS302 Series
 DCS301 Series
 DCS601 Series
 DST301 Series
KRC65, KRC72,
KDC100A10, and KDC101B
Series cannot be connected.
 Tele-con (Field supply)
In case that a central remote
controller is connected
In case that the device coping
with HA JEM-A is connected
 Remote controller
BRC944 Series
 Card key
(Field supply)
 Operating control panel
(Field supply)
 Operating monitoring
equipment
(Field supply)
The adapter included with the
remote controller is not used.
Connecting a Wired
Remote Controller
Connecting a Momentary / constant
Contact Input Equipment
Reading the Operating / error Display
Room Air Conditioners H-Series
EDUS04-906_b
Optional Accessories
5.Control Codes
Tu rn the power on after all the switches have been set.
Settings made while the power is on are invalid.
When using a central remote controller, the operating codes can be used to limit
operation from wireless remote controllers.
: permitted; ´ : prohibited
OFF
(Factory setting)
Overseas
ON
“Automatic” operation
is available from the central controller.
(2) Group number settings (SW1 and SW2-1 to SW2-3)
Set these when using the central controller. (Set to the side.) Do not set more
than one unit to the same number.
However, these settings do not need to be made when using the schedule timer
independently.
(The settings are needed when used in conjunction with another DCS Series
central controller.)
In this case, the schedule timer performs an auto address after the power is turned
on, so new group numbers are automatically set. Settings made using the switches
will be overwritten.
SW2 Upper
setting group NO.
1 1 2 3
Lower
SW1
setting group NO.
1 1 2 3 4
1—
0
Lower
SW1
setting group NO.
1 2 3 4
0 0
0 8
Constant
contact mode
9
2,10-19
0,1,3,5-7
4
8
9
Forced stop
*Only during timer operation
´
´
´
´
´
´
´
´
´
´
´
´
*
*
*
*
´
´
´
´
´
´
´
´
´
´
´
´
*
*
´
*
*
´
´
´
´
´
´
´
´
´
´
´
The remote controller permission / prohibition settings using the Ve-up controller are as
follows.
: permitted; ´ : prohibited
Operations from
central controller,
contact input and
HA JEM-A input
0
1 2 3 4
1 2 3 4
1 2 3
2—
0 1
3—
0 9
0 2
4—
0 3
1 2 3 4
1 2 3 4
1 2 3
5—
1 1
0 4
1 2 3 4
1 2 3 4
1 2 3
6—
1 2
0 5
7—
1 3
1 2 3 4
1 2 3 4
1 2 3
0 6
1 2 3 4
1 2 3 4
1 2 3
8—
1 4
0 7
1 5
NOTE also that a separate timer power source is needed when using the
schedule timer independently.
Power source specs: DC 16V, +10%, -15%, 200mA.
Recommended power source: Omron S82J-01015A. (Should be used with the
output voltage adjusted to the center, DC 16V.)
(3) Settings when recovering from a power outage (SW2-4)
This selects whether to restart operation when the power comes back on after a
power outage occurred during operation. This setting is given priority in cases
where the indoor unit has an auto start ON / OFF jumper. Note also that
regardless of whether switch SW2-4 is on or off, the operating mode, set
temperature, fan direction and speed settings, and remote control prohibition
status are stored.
SW2-4 setting
OFF
(Factory setting)
Instantaneous
contact mode ON / OFF permitted permitted/prohibited
control is
•
Constant rejected prohibited permitted/prohibited
contact mode
permitted
Instantaneous
permitted
prohibited
contact mode Only OFF
prohibited permitted/prohibited
control is
permitted
Constant accepted permitted
prohibited
contact mode
prohibited permitted/prohibited
permitted permitted/prohibited
Instantaneous
contact mode Last command prohibited permitted/prohibited
permitted permitted/prohibited
Constant priority
contact mode
prohibited permitted/prohibited
Forced stop
Does not affect settings
´
´
´
´
´
´
´
´
´
´
´
´
´
´
´
´
KRP928B2S
Power supply for relay (DC 12V)
Operating control panel (Field supply)
MC
S5
M1
M2
What Happens
(–)
(–)
MR1
MR1
MR2
MR2
7.Combining Equipment
Last command priority
Schedule timer
D-BIPS
Forced stop contact input
Constant contact input
Instantaneous contact input
HA JEM-A-compatible equipment
Wired Remote Controller
Wireless Remote Controller
The central controller can be combined with the following devices.
ON / OFF controller
ON / OFF control is rejected
(operate / stop / timer prohibition)
(NOTE 2).
During a forced stop, all
remote controller actions
are prohibited.
Central Remote Controller
ON / OFF controller
´
´
Schedule timer
KRP928B2S
S1
CB
Abnormality display
Control mode
NOTE1: Since central equipment and HA JEM-A-compatible equipment both use
last command priority, the contact status and operating status of the air
conditioner might not match sometimes.
Example: If the unit is run from the central controller while the air
conditioner is stopped with an open contact, the contact will be
open and the unit will be running.
NOTE2: Operating mode and fan direction and speed settings can be changed.
CA
Power source
for display
Operating Display
Central Remote Controller
100 msec or more.
Contact - Open to close: air condition runs.
ON Close to open: air conditioner is stopped
(NOTE 1).
Contact - Open to close: air condition stops
Invalid (forced stop). Close to open: no change in
operating status.
Relay specs (MR1 and MR2)
Coil voltage: DC 12V
Coil resistance: 160W ± 10%
(Matsushita Electric HC
Relay, Omron MY Relay )
Wiring length
Max: 328 ft (100 m)
(+)
The operating status of the air conditioner
ON
´
´
´
6.Read Operating / Error Display Signal
S8
OFF is reversed by an instantaneous input of
Constant contact input
´
´
´
´
Stops after recovering from a power outage
SW3-1 SW3-2
S1
operating mode setting setting
OFF
´
What Happens
(4) Contact input function settings (SW3-1 to SW3-2)
When using contact input (S1), choose one of the following functions.
Instantaneous contact
input (factory setting)
Operating mode Fan direction
temperature and fan speed
Stop
´
The Operating / error signals can be read from the contact output (S5).
Output specs
M1: Tu rn MR 1 ON when the air conditioner is running.
M2: Tu rn MR 2 when a communication error has occurred between the KRP928B2S and
the air conditioner, or MR 1 is ON and the unit has stopped after an error.
MR 2 is not turned ON during a warning.
Stops if the unit was stopped before the power outage
and runs if it was running.
ON
Operations from the remote controller
operating Change set
Start / stop Changemode
temperature Run / timer
1 0
1 2 3 4
1 2 3 4
1 2 3
Ve-up controller settings
S1 pin
operating mode
1 2 3 4
1 2 3 4
1 2 3
Forced stop or remote
controller permission input
Instantaneous Central priority
contact mode
Last command priority
Timer operation
is accepted by
remote controller
´
´
Stop
Japan
is not available from the central controller.
When using “automatic” operation using the wireless remote
controller, the central controller displays automatic cooling
(heating) and 77°F(25°C). Even if the temperature is changed, it
will return to 77°F (25°C) after a while.
Operations from
central controller,
contact input and
HA JEM-A input
Operating mode
temperaturet
Fan direction
and fan speed
0,1,3
10,11
2
12–19
4
5
6,7
8
What Happens
“Automatic” operation
Run / timer
ON / OFF control
is rejected
Only OFF control
is accepted
Operations from the remote controller
“Run” control from the “Stop” control from the
central controller
central controller
Fan direction
and fan speed
SW3-3 setting
Control mode
Control
code
Stop
Destination
S1
operating
mode
Operating mode
temperature
Open the Kit’s case and set the switches on the circuit board.
(1) For Overseas / Japanese unit setting (SW3-3)
Room air conditioners, different methods are used for setting the temperature in
automatic mode, so this switch needs to be set.
Run / timer
NOTE
4.Switch Settings
Run / stop Input
Contact specs
No-voltage minute electric current contact
(Minimum applicable load DC 12V, 1mA or lower)
Total wire length max: 328 ft (100 m)
D-BIPS
´
´
´
´
´
Forced stop contact input
Constant contact input
´
´
´
Instantaneous contact input
´
´
´
HA JEM-A-compatible equipment
´
Wired Remote Controller
´
´
Wireless Remote Controller
´
3P157704-2B
Room Air Conditioners H-Series
77
Optional Accessories
EDUS04-906_b
13.2.3 KPW937A4
 Before Installation
Checking the parts
Check the following parts
Name
Louver
Installation manual
Shape
Quantity
With 4 screws
1piece
1piece
 Installation Procedure
Selection of Installation Location
Use when installing in a location that meets the following conditions.
When installing near the border to a neighbor's house
If exhaust blows directly on passers-by because outdoor unit is installed facing a road.
Changing the fan direction of the outdoor unit to prevent it blowing directly on shrubbery, etc.
Installation of Louver
Installation is possible in the four directions:
upward, downward, rightward, and leftward.
The installation screws are attached to the louver.
First temporarily attach the louver with 4 screws,
then check that the angle is correct, and finally
tighten the screws fully.
Prepared hole
pitch 435mm
Fan partition
Part A
(see figure below)
Prepared hole
pitch 435mm
Fan partition
CAUTION
1.Install so that a short circuit is prevented.
2.For the use in snowy regions, avoid installation
with the air outlet facing upward. Install so that
the air outlet faces leftward, rightward, or downward.
Snow accumulates in the air outlet of the outdoor
unit, causing malfunction of the main body of the
outdoor unit.
3.Be advised that if the fan direction is up,
dead leaves and other foreign matter
easily accumulates in the exhaust vent.
The prepared hole is in between the grating
of the grille. Part A (prepared hole) cross
section (the shape of either a or b)
a) Grille grating
Prepared hole
b) Grille grating
Prepared hole
4P104499-1A
78
Room Air Conditioners H-Series
Daikin Industries, Ltd.’s products are manufactured for export to numerous countries throughout the
world. Daikin Industries, Ltd. does not have control over which products are exported to and used in a
particular country. Prior to purchase, please therefore confirm with your local authorized importer,
distributor and/or retailer whether this product conforms tot he applicable standards, and is suitable for
use, in the region where the product will be used. This statement does not purport to exclude, restrict or
modify the application of any local legislation.
dddddfdf
Ask
a qualified installer or contractor to install this product. Do not try to install the product yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire, or explosion.
Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorized parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire, or explosion.
Read the User’s Manual carefully before using this product. The User’s Manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any inquiries, please contact your local importer, distributor, or retailer.
©
2010 Daikin Industries, Limited.
Daikin® AC Absolute Comfort®, and its design, VRV®, REFNET™, and Quaternity™ are registered trademarks of Daikin Industries, Limited. All rights reserved.
LonWorks® and LON® are registered trademarks of Echelon Corporation. BACnet® is a Data Communication Protocal for Building Automation and Control Networks,
developed under the auspices of the American Society of Heating, Refrigeratin, and Air-Conditioning Engineers (ASHRAE).
ISO 9001 is a plant certification system
defined by the International Organization
for Standardization (ISO) relating to
quality assurance. ISO 9001 certification
covers quality assurance aspects related
to the “design, development, manufacture,
installation, and supplementary service”
of products manufactured at the plant.
ISO 14001 is the standard defined by the
International Organization for Standardization
(ISO) relating to environmental management
systems. Our group has been acknowledged by
an internationally accredited program of
environmental protection procedures and
activities to meet the requirements of
ISO 14001.
AMERICAS
1645 Wallace Drive, Suite 110
Carrollton, TX75006
info@daikinac.com
www.daikinac.com
Specifications, designs and other content appearing in this brochure are current as of October 2010 but subject to change without notice.
EDUS04-906_b
Printed in U.S.A. 10/2010 B AK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising