Behringer EUROLIGHT LD6230 User manual

Behringer EUROLIGHT LD6230 User manual
User Manual
EUROLIGHT LD6230
Professional 6-Channel 10 A Dimmer Pack with DMX and Analog Control
2
EUROLIGHT LD6230 User Manual
Table of Contents
Important Safety Instructions....................................... 3
Legal Disclaimer.............................................................. 3
Limited warranty............................................................. 3
1. Introduction................................................................ 4
1.1 Before you get started....................................................... 4
1.2 The user’s manual................................................................ 4
2. Control Elements........................................................ 5
2.1 Configuration mode........................................................... 6
2.2 DMX mode............................................................................. 6
2.3 ANALOG mode.................................................................... 7
2.4 MANUAL mode.................................................................... 7
3. Applications................................................................ 7
4. Connectors and Initial Operation............................. 8
4.1 Digital DMX connector...................................................... 8
4.2 Analog connector............................................................... 8
4.3 EEP (Eprom Check).............................................................. 8
4.4 Phase allocation................................................................... 8
5. Specifications.............................................................. 9
3
EUROLIGHT LD6230 User Manual
Important Safety
Instructions
Terminals marked with this symbol carry
electrical current of sufficient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. All other
installation or modification should be performed only
by qualified personnel.
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltage inside the
enclosure - voltage that may be sufficient to constitute a
risk of shock.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by
the manufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
Caution
These service instructions are for use
by qualified service personnel only.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER,
KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND
ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY
TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING AND RECORDING OF ANY
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.
ALL RIGHTS RESERVED.
© 2013 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
LIMITED WARRANTY
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
www.music-group.com/warranty.
4
EUROLIGHT LD6230 User Manual
1. Introduction
As a BEHRINGER EUROLIGHT LD6230 owner, you have a high-end dimmer pack
at your hands. It was designed to answer to the high demands of lighting
professionals working in television, theatres and live events, and is therefore
universally applicable.
The EUROLIGHT LD6230 provides all necessary features for controlling your light
show, yet it is clearly laid out and easy to use. It gives you the choice between
analog and digital DMX control. Comprehensive LEDs let you easily detect signal
problems so you can effortlessly eliminate them as soon as they occur.
◊ The following user’s manual is intended to familiarize you with the
unit’s control elements, so that you can master all the functions.
After having thoroughly read the user’s manual, store it at a safe place
for future reference. Installation Instructions supplement the user’s
manual and are included in the shipment.
◊ A qualified professional needs to be present during the unit’s
installation and initial operation. More information about this topic is
covered under Installation instructions.
1.1 Before you get started
1.1.1 Shipment
The LD6230 was carefully packed at the assembly plant to assure secure
transport. Should the condition of the cardboard box suggest that damage
may have occurred please inspect the unit immediately and look for physical
indications of damage.
◊ Damaged units should NEVER be sent directly to us. Please inform
the dealer from whom you acquired the unit immediately as well
as the transportation company from which you took delivery.
Otherwise, all claims for replacement/repair may be rendered invalid.
1.1.2 Initial operation
Please make sure the unit is provided with sufficient ventilation, and never place
the EUROLIGHT on top of an amplifier or in the vicinity of a heater to avoid the risk
of overheating.
◊ Please make sure that the unit is grounded at all times. For your own
protection, you should never tamper with the grounding of the cable or
the unit itself.
◊ To avoid damage to your equipment, always make sure your dimmer
pack is disconnected from the mains before you connect or disconnect
spotlights or other lighting paraphernalia.
◊ Make sure that only sufficiently qualified persons install and operate
your LD6230. To avoid damage or altering of its performance through
electrostatic discharge, make sure that all people handling the LD6230
are properly grounded both during and after the installation.
1.1.3 Rack installation
The LD6230 requires two height units (2 HU) when installed in a 19-inch rack.
Please make sure to leave an extra 4 inches (10 cm) of space behind the unit
for wiring.
Please use M6 machine screws and nuts to install your LD6230 into a rack.
1.1.4 Warranty
Please take a few minutes and send us the completely filled out warranty
card within 14 days of the date of purchase. You may also register online at
behringer.com. The serial number of your EUROLIGHT LD6230 ( (15) ) needed for
registration is located at the rear panel of the unit. Failure to register your
product may void future warranty claims.
1.2 The user’s manual
The user’s manual is designed to give you both an overview of the controls,
as well as detailed information on how to use them. In order to help you
understand the links between the controls, we have arranged them in groups
according to their function. If you need to know more about specific issues,
please visit our website at http://behringer.com.
5
EUROLIGHT LD6230 User Manual
2. Control Elements
Various LD6230 control elements are described in this chapter. All controls and
connectors are described in detail, and you also get useful advice on how to use
them in different applications.
(1)
(2)
(6)
(7)
(8)
(3)
(4)
(5)
Fig. 2.1: EUROLIGHT LD6230’s front panel
(4) Use the UP and DOWN keys to navigate through individual menus.
(1) Ventilation openings are located on the front panel. Their position at
the front assures that hot air does not enter the inside of your rack,
causing equipment failure or damage.
(5) The CONFIG key is used to activate the configuration mode (see ch. 2.1)
and to select individual menus. When used in combination with the
CHANNEL key (see (3) ), you can select different operating modes.
◊ To ensure that your dimmer pack runs smoothly even under full
load, you have to make sure that there is enough distance to other
heat-emitting equipment.
(6) The LEDs to the left of the display have two purposes: supply phase status
indication (L1, L2 und L3) and indication of the operating mode you selected
(DMX, ANALOG and MANUAL).
(2) There is an automated fuse for each of the six dimmer circles. These fuses
engage in the event of overload or short circuit.
(3) Use the CHANNEL key to shift between the six dimmer channels. When used
in combination with the CONFIG key (see (5) ), you can select different
operating modes (DMX, ANALOG and MANUAL).
(11)
(15)
(9)
(10)
(7) The 3-digit DISPLAY shows the values to be edited.
(8) The LEDs to the right of the display relate to the individual menus in the
configuration mode. Depending on the selected function, the corresponding
LED lights up.
(13)
(12)
(14)
Fig. 2.2: EUROLIGHT LD6230’s rear panel
(9) When your LD6230 works in DMX mode, use the 5-pole DMX512 IN-XLR
connector to connect DMX512 control signals (see ch. 2.2 “DMX mode” and
ch. 4.1 “Digital DMX connector”).
(10) You can relay the DMX control signal to additional dimmer packs by using
the 5-pole DMX512 OUT XLR connector. If the dimmer is at the terminal end
of a DMX chain, place a terminator at the DMX output of the dimmer pack to
avoid signal bounce (use a terminator with the resistance of 120 Ω between
pins 2 and 3).
(11) You can connect an analog 0 - 10 V control signal to the 8-pole ANALOG IN
DIN connector (see ch. 2.3 “ANALOG mode” and ch. 4.2 “Analog connector”).
(12) This is the cable slot for connecting your lighting equipment
(see Installation Instructions).
(13) This is the cable slot for the power supply (see Installation Instructions).
(14) The cooling fan is located here.
(15) SERIAL NUMBER. Please take a few minutes and send us the completely
filled out warranty card within 14 days of the date of purchase.
Otherwise, warranty claims may be rendered invalid. You may also register
online at behringer.com.
6
EUROLIGHT LD6230 User Manual
2.1 Configuration mode
2.1.4 Limiter
The important pre adjustments necessary for running the dimmer pack are done
in the configuration mode. Keeping the CONFIG key pressed for roughly two
seconds gets you into the configuration menu. Once you are in the configuration
mode, keep using the CONFIG key to navigate through individual functions,
which are indicated with their respective LEDs located to the right of the display.
To get out of the configuration mode, keep the CONFIG pressed again for roughly
two seconds.
When you press the CONFIG key once again, you get to the LIMITER menu
(the LIMITER LED lights up). Use the CONFIG key to navigate through all six
channels. Here you can set the upper limit for the control signal of each individual
channel. Set the threshold value (16 to 99) by using the UP and DOWN keys.
The LIMITER function too prolongs the life of your light equipment. Limiting the
upper range of control voltage protects from voltage oscillations and overdrive.
◊ All adjustments made in configuration mode are automatically stored
when you exit, and remain stored even when you power the LD6230 on
or off.
2.1.1 Address
As soon as you get to the configuration mode, the ADDRESS LED lights up. In this
menu, you assign DMX basic channels (1 to 507) to the six dimmer channels.
This address determines the DMX channel at which control commands are
executed. Since you are dealing with a 6-channel dimmer, a maximum of six
consecutive DMX channels can be interpreted as control signals, depending on
the assignments in the ASSIGN menu (see ch. 2.1.2). If the start address value is
“001”, then the dimmer reacts to the first six channels of the DMX data stream.
If you, for example, set the start address value to “024”, then the dimmer reacts
to the channels “024” to “029” correspondingly. If several units use the same
DMX address, then they also receive the same control commands.
To select the desired DMX channels, use the UP and DOWN keys. When you keep
one of these keys pressed while tapping the other one simultaneously, this lets
you navigate through the channels in increments of 10 channels at a time.
2.1.2 Assign
When you press the CONFIG key once again, you get to the ASSIGN menu
(ASSIGN LED lights up). In this menu you can make four different input
channel/dimmer channel assignments. Possible configurations:
1-6:All six outputs are dependent on the setting of channel 1.
2-3:Outputs 1-3 are dependent on the setting of channel 1, and outputs 4-6 are
dependent on the setting of channel 2.
3-2:Outputs 1 and 2 are dependent on the setting of channel 1, outputs 3
and 4 are dependent on the setting of channel 2, and outputs 5 and 6 are
dependent on the setting of channel 3.
6-1:All six outputs are separately dependent on the respective six channels (1-6).
If you select one of the first three configuration options, you can for example
form headlight groups that reproduce the same identical program since they are
controlled through just one channel.
After you address DMX channels and assign input and dimmer channels,
you should check if each dimmer circle reacts to the desired DMX control signal
by moving the corresponding faders on the lighting console.
2.1.3 Preheat
When you press the CONFIG key once again, you get to the PREHEAT menu
(the PREHEAT LED lights up). Use the UP and DOWN keys to enter the preheat
value (0 to 15). This preheat value is then continuously run to the headlights,
thus lowering the start-up current requirement and prolonging filament life.
The preheat value you enter is valid for all six channels. However, the PREHEAT
function cannot be used in switch mode (see ch. 2.1.5).
2.1.5 Curve
When you press the CONFIG key once again, you get to the CURVE menu
(the CURVE LED lights up). There are five possible ways to set up the transmission
characteristic of your dimmer pack. You can determine how control voltage
(i.e. fader movement on the mixing console) is transmitted to the lighting
equipment. Step through the six channels indicated on the left-hand digit on
the display by pressing the CONFIG key. Define the transmission characteristic for
each channel separately by using the UP key.
LINEAR (L):
This transmission characteristic linearly increases or decreases control voltages in
all segments of fader movement. When you move a fader on the lighting console,
the headlight intensity changes directly proportionate to the fader movement.
EXPONENTIAL (o1):
In this case, the transmission curve is irregular. When you move the fader on the
lighting console uniformly upwards, the voltage in the lower third of the fader’s
range of movement increases linearly, whereas the transmission characteristic
beyond the first third of the fader’s range of motion becomes more pronouncedly
(exponentially) progressive with each increment of fader motion.
LOGARITHMIC (o2):
This transmission characteristic is also irregular. In the upper third of the
fader’s range of motion the voltage changes linearly, whereas the transmission
characteristic in the lower two thirds gets more pronouncedly degressive with
each increment of fader motion. The logarithmic transmission curve is the
opposite of the exponential curve.
SWITCH OPERATION (US = Unlimited Switch):
In this mode you can use the dimmer circle as a switch. This way, you can use
your LD6230 to control fog machines, motors and various other effects. When the
control voltage reaches 50% or more of a previously specified value, the channel
is switched on. When the control voltage falls below 50%, the channel is
switched off again. LIMITER and PREHEAT functions cannot be used in
this mode.
SWITCH OPERATION (LS = Limited Switch):
In SWITCH OPERATION (LS) the limiter function can be used.
◊ Transmission curves can be separately adjusted for each individual
channel on the EUROLIGHT LD6230.
2.2 DMX mode
Your LD6230 is automatically in DMX mode as soon as the power is up (DMX LED
lights up). Navigate through different modes by using the CHANNEL key while
simultaneously pressing the CONFIG key. Your LD6230 receives the DMX signal via
the DMX512 IN connector, and this signal can be forwarded to additional dimmer
packs using the DMX512 OUT connector in order to process additional channels.
DMX512 IN and DMX512 OUT are 5-pole XLR connectors and are located on the
rear panel.
7
EUROLIGHT LD6230 User Manual
2.2.1 DMX512
Data transmission in the field of lighting equipment refers to transmitting
control information from the lighting console via the dimmer to the headlights,
scanners and similar equipment. This process takes place by using the digital
DMX512 control signal that was developed at the USITT (United States Institute
for Theatre Technology). Information is no longer represented through analog
voltage values; instead, digital data sets are used. In contrast to analog data
transmission, digital signals can simply be “patched” together: each “piece” of
information has an address to which it belongs. Additionally, the following goes
for digital signals: when they arrive at their destination, they have the correct
value since there is no loss of quality associated with analog signals.
Of course, problems may arise here as well. Very often, the reason for faulty
transmissions lies in deploying wrong connectors or connectors other than
those prescribed by the norm. Using wrong cables also may lead to faulty data
transmission. We therefore only recommend using cables that are intended for
use with digital audio technology.
The DMX standard contains 512 digital light channels that are controlled using a
common data cable. However, a maximum of 32 different pieces of equipment
can be connected to any one cable since the cable at some point becomes
overburdened (due to shared controlling of all end equipment). Still, each piece
of equipment can evaluate as much data as you wish. To connect additional
pieces of equipment, you need a so-called splitter or a booster to amplify or to
regenerate the DMX signal.
DMX512 is a compatible norm and requires only one data cable since all
signal recipients are freely addressable, so you avoid having “cable salad”
issues. Once all pieces of equipment are correctly connected and addressed,
a DMX system typically works completely trouble-free.
3. Applications
Lighting equipment is an integral part of almost every performance event and
venue. Be it concerts, theatre or musical acts, clubs or even presentations and
exhibits, they all benefit from good visuals in order to leave a lasting impression
on the audience.
In general, lighting either creates a certain feeling or emphasizes the mood
created through music or dramaturgic composition. Creating a lighting setup
is a demanding and creative endeavour, since it is much more than merely
making a set of lights go on and off. To do this, you need a dependable,
multi-functional set of tools. The EUROLIGHT LD6230 offers a maximum on
functionality and is the perfect expansion for a lighting console, preferably the
BEHRINGER EUROLIGHT LC2412.
Thanks to digital DMX controlling, using multiple dimmer packs lets
you implement demanding lighting setups, since you can control up to
32 components with only one DMX connection. These components don’t
necessarily have to be headlights; in switch mode, you can also control fog
machines, pyrotechnic equipment or motors. This makes the LD6230 much
more than just a piece of lighting equipment.
The following illustration shows a connection example with two
EUROLIGHT LD6230s, a BEHRINGER EUROLIGHT LC2412 and BEHRINGER ULTRAPAR
UP1000 headlights, whereby 12 light channels can be run. The first dimmer
pack is controlled with the digital DMX control signal, the second one with
an analog signal. If both dimmer packs are controlled with the DMX control
signal, the second dimmer pack needs to receive the control signal via the first
dimmer pack:
2.3 ANALOG mode
ULTRAPAR UP1000
In addition to the digital DMX mode, your EUROLIGHT LD6230 dimmer pack also
lets you work in ANALOG mode. You get to this mode by pressing the MODE key
while the CONFIG key is pressed (the ANALOG LED lights up). The analog control
signal (0 - 10 V) is transfered to the dimmer pack via an 8-pole DIN connector
located on the rear panel. This way, you can use the LD6230 with analog
control equipment.
In ANALOG mode, each dimmer channel has a control cable (or a core pair)
of its own. The control signal runs through this cable. The output voltage of the
dimmer is proportionate to the control cable signal. As a rule, 0% is represented
by a voltage of 0 V, 50% is represented by a voltage of 5 V and 100% is
represented by a voltage of 10 V.
DMX512 In
EUROLIGHT LD6230 Rear
◊ When the dimmer pack receives a zero signal level at the input end,
the output signal level should correspondingly be at its minimum.
When the dimmer pack receives a maximum signal level at the input
end, the output signal level should be at its maximum.
2.4 MANUAL mode
To power up your lighting equipment, the EUROLIGHT dimmer pack can be
used even without an external lighting console when in MANUAL mode
(MANUAL LED lights up). In this mode, all settings are automatically saved every
two seconds and can be recalled even after powering the LD6230 off and then on
again. As with other operating modes, you get to MANUAL mode by pressing the
CHANNEL key while the CONFIG key is kept pressed.
The left display digit indicates the channel selected with the CHANNEL key.
The next two digits to its right indicate the level of the control signal, with values
from 0 to 99. Use the UP and DOWN keys to adjust the control signal value.
Analog In
DMX512 Out
Analog Out
EUROLIGHT LC2412 Rear
Fig. 3.1: Connection example with the EUROLIGHT LC2412 and the ULTRAPAR UP1000 headlights
If you need more light channels, connect extra dimmer packs for processing your
control signals.
8
EUROLIGHT LD6230 User Manual
4. Connectors and Initial Operation
4.3 EEP (Eprom Check)
4.1 Digital DMX connector
An eprom (Erasable Programmable Read Only Memory) is an electronic device
that contains programs or data needed to operate a piece of equipment.
Once you “burn” data onto an eprom, it can’t get lost, even when you power
down your equipment.
The DMX512 IN and DMX512 OUT connectors are made in accordance
with the international DMX512 standard. 5-pole XLR connectors are used,
whereby controllers and DMX senders feature female connectors, while receiver
equipment such as dimmer packs feature male connectors.
5-pin XLR connectors for DMX512 signals
During the power-up procedure of your LD6230, the eprom is checked, that is,
the LD6230 looks for false values (plausibility control). If irregularities occur
during the eprom initialisation, factory default values are loaded.
◊ To erase the contents of the eprom and load factory defaults, keep both
middle keys (UP and DOWN) pressed while powering up your LD6230.
4.4 Phase allocation
1 = Signal common/shield
2 = Data 1 (-)
3 = Data 2 (+)
Pins 4 (data 2 -) and 5 (data 2 +) are not connected (optional use)
Fig. 4.1: Pin assignment of a 5-pin XLR connector
You should stick to the pin assignment shown in above illustration even when
two reserve pins 4 and 5 are used for a second connection (a separate sender
and receiver unit).
Often, 3-pole XLR connectors are also used for transmitting digital
control signals, since these connectors simplify using the wiring already
at the user’s disposal and are also less expensive than 5-pole connectors.
However, these connectors are substandard and may not carry the
“DMX512” insignia.
4.2 Analog connector
An 8-pole DIN connector is used as the input connection for an analog control
signal (0-10 V).
PIN
CHANNEL
1
2
3
4
5
6
7
8
1
2
3
4
5
6
NC
GROUND
Tab. 4.1: Pin assignment of an 8-pin DIN connector
The LEDs L1, L2 and L3 ( (6) ) indicate phase condition. L1 refers to channels 1
and 2, L2 refers to channels 3 and 4, and L3 refers to channels 5 and 6. The LEDs
show if correct voltage is applied to your EUROLIGHT LD6230. If the voltage is
not correct (i.e. too high or too low), the corresponding LED(s) begin to blink.
Since the dimmer’s circuitry is powered by all three phases, the dimmer remains
functioning even if two out of three phases malfunction. However, to guarantee
trouble-free operation, always attempt to correct phase problems as soon as they
are discovered.
9
EUROLIGHT LD6230 User Manual
5. Specifications
Channels
Number6
Load per channel
0.2 A min./10 A max.
Maximal load per channel
10 A using a 3-phase connector
Frequency
50/60 Hz
Inputs
Power supply
3-phase connector, internal
terminal block/PG cable screw joint,
CEE connector (optional installation by
qualified professional)
Analog
0 to +10 V via 8-pin DIN
Digital
DMX512 via 5-pin XLR
Outputs
Digital
DMX512 via 5-pin XLR
Load
Internal terminal block/PG cable screw
joint, HARTING (optional installation by
qualified professional)
System Fuses
Load securing per channel
10 A cable protection switch (type C)
Control section fuse
2 x T 100 mA H/250 V (EU)
1 x T 160 mA H/250 V (EU)
2 x T 160 mA H/250 V (UL)
1 x T 315 mA H/250 V (UL)
Power Supply
Voltage
USA/Canada 120 V~, 60 Hz
Europe/U.K./Australia
240 V~, 50 Hz
Maximum power consumption
3 x 20 A
Dimensions/Weight
Dimensions (H x W x D)
approx. 84.3 x 482.6 x 403.8 mm
(approx. 3 1/3 x 19 x 15 9/10")
Weight
approx. 9.80 kg (approx. 21.6 lbs)
BEHRINGER continuously strives to assure the highest quality standards possible. Required modifications may
be implemented without prior notice. Technical data and the appearance of the unit may deviate from the above
values and/or illustrations.
10
EUROLIGHT LD6230 User Manual
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
EUROLIGHT LD6230
Responsible Party Name:
MUSIC Group Services US Inc.
Address:
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
EUROLIGHT LD6230
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
We Hear You
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement