ZIGEN ZIG-HVX 70, 100 HDMI extender User manual

ZIG-HVX-70 / ZIG-HVX-100

HDMI

EXTENDER

ZIG-HVX-70-L/ZIG-HVX-100-L

ZIG-HVX-70-R/ZIG-HVX-100-R

U

SER

M

ANUAL

V1.0

Package Contents-

 1x Transmitter

 1x Receiver

 1 user manual

 2x Power adapter DC 12V with lock

 1x IR Receiver

 4x screws

 8x foot pads

 2x captive screw connectors

Features

 Extend HDMI signal up to 70/100 meter 228/328 Feet by using a single cat-5/6/7

 Supports HDMI 1.4 with 3D function

 Supports HDMI 1.2 and 1.3c

 HDCP Compliant

 Supports 3D pass-through

 Supports CEC pass-through

 Support RS-232(Bi-direction transfer)

 Supports all frequency band IR control(Bi-direction transfer)

 Supports 12-v or 5-volt IR Receiver / Emitter

 Full HD support: 1080p@60Hz, 3D and 4Kx2K

 HD-baseT technology

 Use CAT.5 cable to install easily

Specifications

Function Transmitter Receiver

HDMI In

Connector

HDMI Out

Connector

RJ-45 Connector

HDMI A-Type Female x 1

None

None

1

HDMI A-Type Female x 1

IR Terminal

Block

IR OUT

1

3.5ψ Stereo Jack x 1 3.5ψ Stereo Jack x 1

IR IN 3.5ψ Stereo Jack x 1

On-board x1

3.5ψ Stereo Jack x 1

Max. Resolution

Cable Distance

Power Adapter

(Min.)

Housing

Weight

Dimensions

(LxWxH)

1080P 60Hz 4K x 2K

70/100 m (Max.)

296g

DC 12V with lock

Metal

150x74x24 mm

303g

-1-

LOCAL FRONT VIEW

1. IR OUT

2. IR IN

3. IR Terminal Block

4. HDCP LED

5. LINK LED

6. MODE LED

7. POWER LED

REMOTE FRONT VIEW

1. IR2 IN

2. IR OUT

3. IR Terminal Block

4. IR1 IN

5. HDCP LED

6. LINK LED

7. MODE LED

8. POWER LED

LOCAL/REMOTE REAR VIEW

1. Power jack (12V DC)

2. LINK (RJ-45 Connector)

3. HDMI IN(Local)/HDMI OUT(Remote)

4. RS-232

-2-

Installation

1. Be sure to turn OFF your HD source and HDTV.

2. Connect the HDMI extension cable between HD source and the “HDMI IN” port of Transmitter.

3. Connect the HDMI extension cable between the HDTV and the “HDMI OUT” port of Receiver.

4. Connect CAT.5 cables between the Transmitter “LINK” port and the Receiver “LINK” port of extender.

5. Connect the power cord and power up the extender.

6. Turn on your HD source and HDTV.

IR Receiver Cable Directions:

Plug the IR Receiver into the ZIG-HVX-70-R/

ZIG-HVX-100-R “IR2 IN” port and place the IR Receiver

Cable, so that you can point to it easily with your IR remote controller.

IR Emitter Directions:

Plug any brand IR emitter into ZIG-HVX-70-L/

ZIG-HVX-100-L “IR OUT” port, and place the IR censor directly on the device ( IR in window located on the front panel ) which you intend to control.

Additional Options

Select any additional options you may require.

1. IR Receiver Cable

GND

+V

Sig

-3-

Technical Specifications Output Signal

Pin # Signal

1 TMDS Data 2+

2 TMDS Data 2 Shield

3 TMDS Data 2-

4 TMDS Data 1+

5 TMDS Data 1 Shield

6 TMDS Data 1-

7 TMDS Data 0+

8 TMDS Data 0 Shield

9 TMDS Data 0-

10 TMDS Clock+

Pin # Signal

11 TMDS Clock Shield

12 TMDS Clock -

13 CEC

14

Reserved

(N.C. on device)

15 SCL

16 SDA

17 DDC/CEC Ground

18 +5 Power

19 Hot Plug Detect

DO NOT PLUG MONO TIPE IR EMITTER IN TO “IR-IN”

IR-in is design to be used with IR receivers.

-4-

Wiring Information & Coding

Conductor

Identification

Pair 1

Pair 2

Pair 3

Pair 4

RJ45 Pin

Assignment

5

4

1

2

3

6

7

8

Color Code for

Conductor

White-Blue

Blue

White-Orange

Orange

White-Green

Green

White-Brown

Brown

-5

©

Trademarks:

All rights reserved

All the companies, brand names, and product names referred to this manual are the trademarks or registered trademarks belonging to their respective companies.