Digital Monitoring XR5 null

Digital Monitoring XR5 null
LCD Keypad User's Guide
for XR5FC and XR5SL Fire Panels
Description
ENTER CODE
The XR5 fire system has been designed with your safety in mind using
the latest in computer technology. The system combines ease of use
with a simple to understand LCD (Liquid Crystal Display) keypad to offer
the full range of features demanded by today’s fire professionals.
The system requires you to enter the user code. As you enter the code,
the display shows an asterisk (*) in place of each digit pressed.
About the keypad
PH LINE 1 TRBL
This device has been placed at locations throughout the premises to
allow you to properly operate the system and review previous event
history. The keypad provides a passcode protected User Menu where
you can access the functions needed to operate the system. See
Keypad User Menu below. In addition to the User Menu, the items
below list operational features of your keypad.
There is a problem with the phone lines connected to your system. Call
for service as soon as possible.
The SELECT keys
TRY AGAIN
These keys allow you to choose an option by pressing the SELECT key
under choices being shown in the display.
The user code you've entered is not recognized by the system. Check
the code and try again.
INVALID CODE
The user code you've entered is considered invalid by the system.
TROUBLE
There is a problem with a protection device or system component. This
display is accompanied by a description of the problem.
SERVICE REQUIRED or SYSTEM TROUBLE
Power
LED
There is a problem on the system. Call for service.
Lighted Display
SILENCED
ARROW key
SELECT keys
AB C
5
Data Entry
keys
3
2
1
9
4
GHI
DEF
7
6
M NO
PQ R
JK L
8
STU
0
VW X
COMMAND
YZ
COMMAND
key
LCD Keypad
Lighted display
The keypad uses a backlit display and plain English text to show events
occurring on your system.
Data Entry keys
These keys allow you to enter the code number when using the system.
The ARROW key
The ARROW key allows you to back up through the list of functions in
the User Menu or make corrections when entering information.
The COMMAND key
The COMMAND key allows you to advance through the keypad displays
and enter information into the system.
Power LED
This remains on steady as long as your fire system is connected to its
AC power supply. Should there be an interruption, the green LED will
turn off. The system's backup battery maintains normal operation for a
time allowing you to contact our service department. Should the battery
power become low, the Power LED flashes.
Special Fire Command Tones
Your keypad also contains a small speaker that allows it to alert you to
events as they occur on your system. Below are brief descriptions of the
different tones you'll hear from the keypad:
Key press tone: A short beep when you press a key on the keypad.
Trouble tone: A steady tone indicating a trouble condition on your
system. Enter the user code to silence the trouble tone.
Fire Alarm Tone: Your keypad may sound a siren-like tone in one
second intervals. This is in addition to other bells or sirens you may have.
Understanding Fire System Terms
Zone
A zone refers to a group of one or more protection devices. For example,
smoke detectors on the east side of the premises can be grouped
together as the zone EAST SMOKES.
Central Station Monitoring
Your system can also be programmed to send alarm and trouble reports
to a central station where operators can dispatch the appropriate
authorities.
Status List
Status is a feature that automatically displays the status of your system
on the keypads. The Status List displays alarm or trouble conditions on
zones and trouble conditions that occur with AC or battery power or the
phone lines. If more than one alarm or trouble condition occurs at the
same time, the keypad sequences this information on its display.
Silencing the Bells During an Alarm
While the alarm bell or siren is sounding, enter the user code. The
keypad displays ALARM SILENCED.
Special Fire Command Messages
Silencing the keypad trouble sounder
SYSTEM NORMAL
This display indicates that fire protection devices, phone lines to the
panel, and the panel itself, are in good condition.
To silence the trouble sounder, press any key on the keypad. To silence
the keypad sounder when a Supervisory zone is in alarm, you must enter
the user code.
ALARM
Keypad User Menu
A fire, supervisory, or auxiliary zone has been tripped. Your system may
sound the fire bells.
Many of the features of your system have been put into a User Menu you
can access from the keypad. The menu requires you to enter the user
code before you can access any functions.
ALARM SILENCED
A user has silenced the fire bells by entering the code or by using the
Alarm Silence function in the User Menu.
BYPASS
A zone has been disabled by the system due to repeated trips. If the zone
remains normal for one hour it can be restored into the system.
To access the User Menu:
1. Press the COMMAND key until MENU? NO YES displays.
2. Select YES. The keypad displays ENTER CODE: –. Enter the user
code. You can now scroll down through the list of system features.
The back of this page details the User Menu functions.
Copyright © 1996 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice.
Sensor Reset
Function: Sensor Reset temporarily removes power to smoke detectors
allowing them to reset after they have tripped. The detectors must be
reset before they can detect any additional alarm conditions.
Make sure all smoke is cleared from around the smoke detectors before
performing a Sensor Reset to prevent the alarm from occurring again.
3. The keypad displays the first recorded event. Use COMMAND to
scroll down through the event displays.
Use the ARROW key to scroll back up through the event displays. If you
press the ARROW key when you first enter Display Events, the keypad
returns to the Status List.
Zone Event Displays
1. Access the User Menu.
2. When SENSOR RESET? is displayed, press any SELECT key. The
keypad displays SENSORS OFF for five seconds followed by
SENSORS ON.
3. The keypad returns to the status display.
Enter the user code to reset sensors
You can also just enter the user code and press COMMAND to reset the
sensors without having to enter the User Menu.
System Test
Function: Tests the battery, alarm bell or siren, and communication to
a central station. The System Test function begins automatically as soon
as you select it.
1. Access the User Menu. Press the COMMAND key until SYSTEM
TEST? displays.
2. Press any SELECT key. The system test begins automatically and
the keypad displays:
# FIRE ALARM
The display actually contains three separate sections.
# - Records the zone number. Press the SELECT key under the zone
number to display the custom zone name programmed into the system.
FIRE - This is the type of zone on which the activity occurred. There are
three possible zone types you may see on your keypad.
FIRE -Fire
SUPV -Supervisory
AUX1 -Auxiliary 1
ALARM - This is the event that occurred. There are 3 event types:
ALARM
TROUBLE
RESTORE
Zone Bypass Event Displays
# BYPAS
BYPAS - This zone has been bypassed by the system.
RESET - This zone has been reset by the system.
1) BELL SOUNDING during a two second bell test, then:
Press the SELECT key under the zone number to display the custom
zone name programmed into the system.
2) BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery, then:
Supervisory Event Displays
* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test, then:
4) TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test, then:
5) TEST END to indicate the System Test is complete.
6) You can cancel the transmit test by pressing the ARROW key.
* The transmit test does not operate on local systems.
Fire Drill
Function: Allows you to practice fire drill evacuations.
1. Access the User Menu. Press COMMAND until FIRE DRILL
displays.
2. Press any top row key. The keypad displays SURE? NO YES.
Press the SELECT key under YES. The system rings the bells until
you enter the user code or until the programmed bell time expires.
User Codes
Function: Allows you to change the user code number you enter at the
keypad. NOTE: The user code must always have four digits.
1. Access the User Menu. Press COMMAND until CODE NO: * * * *
displays. Press a SELECT key. The keypad displays CODE NO: –.
Enter a new 4-digit user code. If the code you entered is a special
service code used internally by the system, the keypad displays
ALREADY IN USE. You must enter a different user code.
Display Events
Function: Allows you to review up to 16 past events that occurred on
your system in the order of their occurrence.
POWER TROUBLE
The display contains two separate sections.
POWER - The type of condition that occurred on your system.
POWER -
Problem with the AC power supply.
BATTERY - Problem with a low battery. This could be due to the
battery exceeding its life expectancy. Call the service
department whenever you see a low battery display.
There are only two status conditions for supervisory events.
TROUBLE
RESTORE
Auto Recall Event Displays
Your system sends periodic recall (test) reports to the central station to
test the communications link. Each successful test transmission is
logged into the Display Events and shown as AUTO RECALL.
Emergency Evacuation Plans
The National Fire Protection Association recommends you establish an
emergency evacuation plan to safeguard lives in the event of a fire or
other emergency. Use the following steps as a guide.
Draw a floorplan of your home or business
On a sheet of paper, draw the walls, windows, doors, and stairs. Also
draw any obstacles a person may encounter exiting the building.
Develop escape routes
Determine at least two routes occupants in each room can take to safely
escape. One route can be the most obvious such as the door. Another
can be through a window that can be easily opened.
Draw arrows on the floorplan to show escape routes from each room.
There are two event types recorded by the system:
Decide where to meet
Zone Events - Records zone alarms, troubles, and restorals.
Prearrange a meeting place at a neighbor's house or across the street
in the front of the house. Always perform a head count to make sure all
occupants safely exited. NEVER ENTER A BURNING BUILDING. If the
head count shows a person missing, give this information immediately
to the authorities. Never enter a burning building to look for someone.
Supervisory - Records problems with the system’s hardware components.
The system’s memory can hold up to 16 events. Once these events are
stored, any new event causes the oldest event to be cleared.
1. Access the User Menu.
Practice your escape plans
2. Press COMMAND until DISPLAY EVENTS? displays. Press any
SELECT key.
Devising an escape plan is only the beginning, before the plan can be
effective everyone should practice the escape routes from each room.
LT-0296 (7/96)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement