Quick Installation Guide Model # AICN1777W SkyIPCam1777W

Quick Installation Guide Model # AICN1777W SkyIPCam1777W

Quick Installation Guide

SkyIPCam1777W

Wireless N MPEG4 Night Vision

Pan & Tilt Network Camera

Model # AICN1777W

Ver. 1A

Package Contents

Wireless N Night Vision Pan & Tilt Network Camera

AC Power Adapter

Wall Mount Kit

GPIO & RS485 Adapter

Ethernet Cable (RJ-45 type)

Setup

Quick Installation Guide

System Requirement

z

Accessing the Camera using Web Browser

- Supported Browsers:

Microsoft® Internet Explorer 6.0 or above;

Apple Safari and Mozilla Firefox with JAVA plug-in

­

CPU:

for MJPEG and QuickTime plug-in for MPEG4

Intel Pentium III 800MHz or above z

­

RAM:

512MB

­

Resolution:

800x600 or above

Accessing the Camera using Software SkyIPCam UltraView

­

Platform: Microsoft® Windows® 7, Vista, XP

­

­

Hard Disk:

Resolution:

80GB or above

1024x768 or above

­

Suggested Hardware Requirement

● 1~8 cameras connected:

Intel Core 2 Duo; 2GB RAM

● 9~32 cameras connected:

Intel Core 2 Quad; 4GB RAM

NOTE

If you connect multiple cameras and monitor them simultaneously, it is recommended that you use a computer with higher performance.

This Quick Installation Guide only provides basic instructions. For detailed information, including the instructions of the complimentary software, please refer to the User’s Manual on the supplied CD.

1

Section 1

„

Getting to Know Your Camera

Front and Top View

LED Indicators:

Power

(left, steady amber light) indicates the camera is powered on.

Link

(right, flashing green light) indicates the camera’s network connectivity.

Infrared LEDs (X7)

allow the camera to capture clear images in a dark environment.

Light Sensor

is used to trigger on and off the Infrared LEDs depending on the surrounding light level.

Antenna

Internal Microphone

allows the camera to receive sound and voice.

USB Port

is used to connect an external

USB device.

2

„

Rear View

GPIO

is used to connect the external devices.

Reset Button

will restart the camera when it is pressed quickly; when it is pressed and held for five seconds, the camera will restore the factory default settings.

USB Dismount Button

is used to safely disconnect an USB device.

Audio-Out Connector

connects to an external speaker.

Ethernet Cable Connector*

connects to the network cable, which supports the

NWay protocol so that the camera can detect the network speed automatically.

DC Power Connector

connects the AC power adapter, in order to supply power to the camera.

Antenna Connector:

connects to an external antenna.

3

Section 2

Hardware Installation

Step 2.1

Attach the included external antenna to the camera.

Step 2.2

Connect one end of the Ethernet cable to the IP Camera and connect the other end to one of the LAN ports on your router or switch.

Step 2.3

Power on the IP Camera by connecting one end of supplied power adapter to the power jack of the Camera and connecting the other end to an electrical outlet.

Step 2.4

Verify that the orange light (Power) is solid and the green light

(Link) is blinking.

4

Section 3

Installing SkyIPCam Utility and UltraView

Step 3.1

Insert the provided CD into your computer’s CD ROM drive.

Step 3.2

Click on

Install Utility and Software

when the autorun menu pops up on the screen.

5

Note: If you do not see the above autorun menu pops up on the screen, please go to your

CD-ROM drive

>

UltraView

folder > run “

Setup.exe

”.

Windows 7 and Vista users:

an AutoPlay window pops up on screen, please make sure you give permission to run the setup program by clicking

Autorun.exe

.

6

Step 3.3

Click

Install

to install the SkyIPCam utility and UltraView.

Step 3.4

Click

Finish

when installation finishes.

7

Section 4

Configuring the Camera

Step 4.1

Go to

Start > (All) Programs > Airlink101 SkyIPCam UltraView

> SkyIPCam Utility

.

Step 4.2

Click on

Search

to find the camera on your network. Select the

Camera you wish to configure and click on

Link

.

Note

If the Camera you wish to configure does not show up in the utility, make sure the camera is properly connected to the same local network as your computer is, and the Green LED should be on. Click on

Search

to try again.

8

Step 4.3

When you are prompted for the user name and password, enter

“admin”

for both

User name

and

Password

, and click

OK

.

Step 4.4

The camera viewing window will appear. Click on

Setup

, then click on

Smart Wizard

.

9

Step 4.5

Enter a name for your camera and a location (i.e. RoomA01).

Create a password and enter to

Admin Password

and

Confirm Password

.

This will change the admin password of the camera. It is recommended to modify the admin’s password to protect your privacy. Click

Next

.

Step 4.6

You may simply accept the suggested default setting

DHCP

if your router’s

DHCP

server is enabled, so the router will automatically assign a dynamic

IP

address to your camera. Another option is to select

Static IP

, and enter IP, Subnet Mask, Default Gateway, Primary/Secondary DNS addresses here.

Note Be sure to enter Primary/Secondary DNS addresses assigned by your ISP if you set up Static IP for the camera so that the Email alert /

FTP uploading can function properly.

10

Step 4.7

If you would like to set up email alerts that you can receive in the future, enter your email information here. You can get this information from your Internet Service Provider. You can also set this up at a later time. Click

Next

.

Step 4.8

If you would like to connect the camera wirelessly to the network, enter the wireless information according to your wireless router’s (or access point’s) wireless settings. You can log into the router’s (or AP’s) web configuration pages to get the SSID and encryption details. Click

Next

.

11

Step 4.9

Confirm your settings at this page. If everything is correct, click

Apply

to save the settings, then the camera will restart in 50 seconds.

12

Section 5

Viewing Image

Method A > Access Camera from SkyIPCam Utility

Step 5.1A

Open Airlink101 SkyIPCam Utility, select the camera you wish to connect to and click on

Link

button. Go to

Step 5.3

.

13

Method B > Access Camera from Web Browser

Step 5.1B

If you assigned a static IP address for your camera (at Step 4.6), you may open the Web Browser on your computer.

Step 5.2B

Type the IP address of your camera in the Address bar, and press

Enter

.

Step 5.3

Enter user name and password, then click

OK

. The default user name and password are both “

admin

” if you did not make any change to it at Step 4.5.

14

Step 5.4 Internet Explorer User:

If this is the first time for your computer to view image from the web configuration page, you will be prompted to install the ActiveX Control. Click on the bar on top of the screen and click on

Run

Add-on

or

Install ActiveX Control

(depends on different IE versions).

Step 5.5

Click on

Run

, then you will be able to view the image.

Note

If you are using Mozilla Firefox or Safari and you are not able to view any image, please make sure you have Java and Quick Time add-ons installed.

15

Step 5.6

To get a clear view of images, you can simply rotate the camera’s lens clockwise or counter-clockwise to adjust the focus.

16

Section 6

Technical Support

E-mail: [email protected]

Toll Free: 1-888-746-3238

Website: www.airlink101.com

* AICN1777W supports most of the mobile devices, but compatibility with every mobile device is not guaranteed.

** Monitoring multiple cameras simultaneously demands high performance computer system.

*** Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic as well as network overhead lower actual data throughput rate.

Specifications are subject to change without notice. Photo of product may not reflect actual content. All products and trademarks are the property of their respective owners. Copyright

©2011 Airlink101®

17

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement