Healthometer Connectivity Kit Directions for Use

Healthometer Connectivity Kit Directions for Use
MODEL C-HOMWA-1
CONNECTIVITY KIT, CONNEX (USB)
MODEL L-HOMWA-1
CONNECTIVITY KIT, LXi (RS-232)
USER INSTRUCTIONS
UMHOMWA
Rev 20110525
Patent Pending
GENERAL
Thank you for purchasing this product. It is important that you read through this manual
before installing this product to avoid problems during set-up and use.
Both the C-HOMWA-1 and the L-HOMWA-1 connectivity kits allow communication
between the Health o meter scale and the Welch Allyn Spot LXi or Connex device. The CHOMWA-1 Connectivity Kit transfers weight, height and BMI data from the Health o meter
digital scale to the Welch Allyn Connex® Device for display on the device. The LHOMWA-1 Connectivity Kit transfers weight data from the Health o meter digital scale to
the Welch Allyn Spot Vital Signs® LXi Device for display on the device.
WARNING – Electric Shock Hazard. Do not connect an external power
supply to the scale. The scale should operate on batteries only when used
with the Connectivity Adapter.
The Connectivity Adapter is intended only as an accessory to other Listed
medical equipment where the combination has been investigated and tested
for leakage current as a system before being put into service.
PRODUCT CONTENTS
Model C-HOMWA-1 Connectivity Kit, Connex (USB) [For use with Welch Allyn
Connex devices]
1 – HOMWA-1
Connectivity Adapter
1 – SP62941
1ft (.31m) USB Cable (Connects Scale to Adapter)
1 - SP62979
2m (6.6ft) USB Cable (Connects Connex to Adapter)
1 - UMHOMWA
User Instructions (on CD)
Model L-HOMWA-1 Connectivity Kit, Lxi (RS-232) [For use with Welch Allyn Spot
Vital Signs LXi devices]
1 – HOMWA-1
Connectivity Adapter
1 – SP62941
1ft (.31m) USB Cable (Connects Scale to Adapter)
1 – CSMN9MF-5
5ft (1.5m) D-Sub Cable (Connects LXi to Adapter)
1 – UMHOMWA
User Instructions (on CD)
PRODUCT SET- UP
Note: The scales listed are those that currently use the Connectivity Adapter.
Please note that Health o meter might be adding scale models to this list, so
please consult your distributor or the Health o meter website
(www.homscales.com) for an updated list.
The “TO LXi” connector on the Connectivity Adapter is intended only for
connection to connectors of equipment complying with double insulation
requirements of UL60601-1/CSA22.2 No.601.1
2
UMHOMWA
Rev. 20110525
The “TO SCALE” connector on the Connectivity Adapter is intended for
connection to Health o meter scales complying with double insulation
requirements of UL60601-1/CSA22.2 No. 601.1.
The “TO CONNEX DEVICE” connector on the Connectivity Adapter is
intended for connection to circuits that are not live and that are separated
from mains by at least basic insulation as defined by UL60601-1/CSA C22.2
No. 601.1.
Note: “CONNEX” is a general trade name for the family of Welch Allyn products
such as the 6000 Series Vital Signs Monitor.
Mounting the Connectivity Adapter
1. For Health o meter scales with a pillar (Models 499KL, 500KL, 500KLWA, 522KL,
522KLWA, 597KL, 597KLWA, 597KG, 597KGWA, 599KL, 599KLWA, 599KG,
599KGWA) the Connectivity Adapter is mounted to the back of the pillar below the
display head as shown in Figure 1 and Figure 2. Clean the area on the pillar where
the adapter is to be mounted. Remove the protective film from the Velcro tape on
the back of the connectivity adapter and mount the adapter to the scale pillar. Make
certain that the end of the adapter with the two connectors labeled “To Scale” and
“To LXi” is facing the display head.
2. For Health o meter scales with hand rails (Models 1100KL, 1600KL, 2101KL,
2101KG, 2101KGWA, 2500KL, 2500KG, 2500KGWA, 2600KL, 2600KG,
2600KGWA, 2610KL) the Connectivity Adapter is mounted to the underside of the
hand rail bar the display head is mounted to as shown in Figure 3. Clean the area
on the hand rail where the adapter is to be mounted. Remove the protective film
from the Velcro tape on the back of the adapter and mount the adapter to the
display head handrail bar so that the end of the adapter with the two connectors
labeled “To Scale” and “To LXi” faces the display head.
9in
(22.8cm)
6in
(15.2cm)
Figure 1
500KL Scale
Figure 2
597KL Scale
(Allow enough cable slack
for head to pivot)
3
UMHOMWA
Rev. 20110525
Figure 3
2101KL Scale
3. For Health o meter scales with a remote display head (Models 498KL, 752KL,
752KG, 752KGWA, 753KL, 2400KL, 2650KL, 2650KG, 2650KGWA, 2700KL) the
Connectivity Adapter is located close to the display head and can be mounted as
required with the Velcro tape on the back of the adapter. Mount the adapter so that
the adapter end with the two connectors labeled “To Scale” and “To LXi” is facing
the scale display head.
Connecting the Adapter: C-HOMWA-1 Connectivity Kit, Connex (USB)
1. Using the SP62941, 1 foot USB cable, connect the “TO SCALE” USB connector on
the adapter to the USB connector located on the back of the scale display head.
2. Using the SP62979, 2 meter USB cable, connect the “TO CONNEX DEVICE” USB
connector on the adapter to the USB connector behind the USB door on the back of
the Welch Allyn Connex Device.
Connecting the Adapter: L-HOMWA-1 Connectivity Kit, LXi (RS-232)
1. Using the SP62941, 1 foot USB cable, connect the “TO SCALE” USB connector on
the adapter to the USB connector located on the back of the scale display head.
2. Using the CSMN9MF-5, 5 foot serial cable, connect the “TO LXI” DB-9 connector on
the adapter to the DB-9 connector (labeled 1) on the back of the Welch Allyn Spot
Vital Signs LXi Device.
PRODUCT USE
The Connectivity Adapter works with a variety of Health o meter digital scales and must
recognize the scale it is first connected to in order to establish a proper communication link
between the scale and Welch Allyn device. This initialization is accomplished by taking one
or more weighings on the scale until a weight is displayed on the Welch Allyn device.
Once this is done, the adapter remembers the scale and does not require initialization
even if the Welch Allyn device or Health o meter scale is disconnected, or is turned off and
back on.
4
UMHOMWA
Rev. 20110525
PRODUCT USE - Continued
When used with the Welch Allyn Spot Vital Signs LXi Device
Note: On the device, make certain the Weight Scale option is enabled in the External
Devices menu. For more information, see the Internal Configuration section of the Spot
Vital Signs LXi Directions for Use.
1. Turn power on to the Welch Allyn Spot LXi. Note that the “Power” and “Connected”
LEDs on the Connectivity Adapter will not be illuminated.
2. Turn on the Health o meter scale and wait for a zero display.
3. Weigh yourself by following the procedures for weighing. After the scale has
stabilized and locked, the weight measurement is transferred to the LXi Device.
4. Check the LXi Device for a weight measurement. If a weight measurement is
displayed, the adapter has initialized and has established a communication link
between the scale and the LXi Device. If not, weigh yourself one or two more times
until the weight is displayed on the LXi Device.
5. Follow the procedures for scale and LXi Device use.
When used with the Welch Allyn Connex Device
Note: Make certain that the license enabling communication between the Connex
Device and the scale is active. For instructions on enabling the weight scale
communication license, see the Welch Allyn Service Tool Installation and Configuration
Guide that shipped with your Connex Device.
Note: Make certain that the Connex Device is configured to automatically display
weight, height and BMI measurements. For more information, see the Welch Allyn
Connex Device Directions for Use.
1. Turn on the Connex device. Verify that the green “Power” LED and the green
“Connected” LED on the Connectivity Adapter illuminate. This is an indication that
the adapter has power and is communicating with the Connex Device.
2. Turn on the Health o meter scale and wait for a zero display.
3. Weigh yourself by following the procedures for weighing. After the scale has
stabilized and locked, the weight measurement is transferred to the Connex Device.
4. Check that the weight measurement is displayed under the Weight label on the
Connex Device Home tab. If a weight measurement is displayed, the adapter has
initialized and has established a communication link between the scale and the
Connex Device. If not, weigh yourself one or two more times until the weight is
displayed on the Connex Device.
5. Follow the procedures for scale and device use.
Note: When a measurement is transferred from the scale to the Connex
Device, the measurement displayed on the device is within one decimal place
(0.1) of the measurement displayed by the scale.
5
UMHOMWA
Rev. 20110525
TROUBLESHOOTING
Refer to the following instructions to check and correct a failure before contacting service
personnel.
Welch Allyn Spot Vital Signs LXi Device
Symptom
Possible Cause
1. Bad cable connection.
2. Wrong connection to
LXI.
No weight displayed on
monitor.
3. Adapter hasn’t
initialized.
4. Weight scale option is
not enabled
Corrective Action
1. Make certain cable plugs
are fully seated in their
respective jacks.
2. Make certain cable is
plugged in to connector
labeled “1” on LXi.
3. See ‘Product Use’
section (page 5) for LXi.
4. Enable the weight scale
option in the External
Devices menu. See the
Internal Configuration
section of the Spot Vital
Signs LXi Directions for
Use.
Welch Allyn Connex Device
Symptom
No weight displayed on
monitor
Possible Cause
1. Bad cable connection.
1.
2. Adapter hasn’t
initialized.
2.
3. Weight scale license is
not enabled on the
Connex Device.
3.
“Power” LED on Adapter
not lit.
4. Weight, or height, or
4.
BMI not displayed on
Connex Device.
1. Bad cable connection to 1.
monitor.
2. No power to Adapter.
2.
“Connected” LED on
Adapter not lit.
1. Poor Adapter/monitor
power up sequence.
6
1.
Corrective Action
Make certain cable plugs
are fully seated in their
respective jacks.
See ‘Product Use’
section (page 5) for
Connex Device.
Enable the weight scale
communication license
on the device (See
Welch Allyn Service Tool
Installation and
Configuration Guide).
Configure the device to
display weight, height
and BMI.
Make certain cable plugs
are fully seated.
Turn on the Connex
Device.
Power cycle the Connex
Device.
UMHOMWA
Rev. 20110525
ENVIRONMENTAL SPECIFICATIONS
Storage Temperature: -18°C to 60°C (0°F to 140°F)
Operating Temperature: 10°C to 50°C (50°F to 122°F) 10% - 90% RH
Note: This device complies with CISPR 11, FCC Part 15, and ICES-003 radiated
emissions requirements. This device does not cause harmful interference, and will
accept any interference received, without causing undesired operation.
MAINTENANCE AND CLEANING
Maintenance
1. Check the overall appearance of the adapter for any obvious damage, misuse, etc.
2. Inspect the condition of the cables connected to the adapter and replace if needed.
Cleaning
1. Do not immerse the adapter into cleaning or other liquid solutions.
2. Clean the adapter and cables with the following recommended products by wiping
down the adapter and cables.
• PDI Sani-Cloth (Ammonium Chlorides)
• Sani-wipes
• 10% Bleach Solution
• Cidex Plus (3.4% Glutaraldehyde)
2 YEAR LIMITED WARRANTY
What does the Warranty Cover?
This Health o meter® Connectivity Adapter is warranted from date of purchase against
defects of materials or in workmanship for a period of two (2) years. If product fails to
function properly, please contact one of the customer service centers listed below. If the
manufacturer determines that a defect of material or in workmanship exists, the customer’s
sole remedy will be repair or replacement of the scale at no charge. Replacement will be
made with a new or remanufactured product or component. If the product is no longer
available, replacement may be made with a similar product of equal or greater value. All
parts including repaired and replaced parts are covered only for the original warranty
period.
Who is Covered?
The original purchaser of the product must have proof of purchase to receive warranty
service. Please save your invoice or receipt. Authorized dealers selling Pelstar products do
not have the right to alter, or modify or any way change the terms and conditions of this
warranty.
7
UMHOMWA
Rev. 20110525
2 YEAR LIMITES WARRANTY - Continued
What is Excluded?
Your warranty does not cover normal wear of parts or damage resulting from any of
the following:
Negligent use or misuse of the product, use on improper voltage or current, use contrary to
the operating instructions, abuse including tampering, damage in transit, or unauthorized
repair or alternations. Further, the warranty does not cover natural disasters, such as fire,
flood, hurricanes and tornadoes. This warranty gives you specific legal rights, and you may
also have other rights that vary from country to country, state
to state, province to province or jurisdiction to jurisdiction.
To get Warranty Service make sure you keep your sales receipt or document
showing proof of purchase. Call one of the following customer service centers:
USA & Canada - (+1) 800-638-3722
European Call Center - (+353) 46-90-67790
France - (+33) 1-55-69-58-49
Germany - (+49) 695-098-5132
Italy - (+39) 026-968-2425
Netherlands- (+31) 202-061-360
Spain - (+34)917-499-357
Sweden - (+46) 85-853-6551
United Kingdom - (+44) 207-365-6780
Latin America - (+1) 305-669-9003
Middle East - (+49) 7477-927186
South Africa - (+27) 11-777-7555
Australia - (+61) 2-9638-3000
China - (+86) 21-6327-9631
If your Connectivity Adapter is not covered by warranty, or has been damaged, an
estimate of repair costs or replacement costs will be provided to you for approval, prior to
servicing or replacing.
PELSTAR, LLC
11800 South Austin Avenue • Alsip, IL 60803 • USA
1-800-638-3722 or 1-708-377-0600
www.homscales.com
PLEASE REGISTER YOUR ADAPTER FOR WARRANTY COVERAGE AT:
http://www.homscales.com/customers/registration.aspx
Health o meter® Professional products are manufactured, designed and owned by Pelstar, LLC.
Health o meter® is a registered trademark of Sunbeam Products, Inc. used under license. We reserve the right to
improve, enhance or modify Health o meter® Professional product features or specifications without notice.
© Pelstar, LLC 2011
8
UMHOMWA
Rev. 20110525
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement