Chuango KP-700 Specifications

Chuango KP-700 Specifications
KP-700
Keypad
Operation Manual
Please read this manual carefully before use.
Please keep it properly for further reference.
Printed in Hong Kong
PA: OI-KP700/EN-2013V1.0
Table of Contents
Usage
Introduction
Foreword
1
Arm
19
Parts List
2
Disarm
20
Appearance
3-4
Preparation before Use
Power on
5
Connect Keypad to Control Panel
6
Connect RFID Tag to Keypad
6-7
Connect Electronic Door Lock
8
Installation
8
Stay Mode
21
Emergency Call
22
Mute Mode
22
Care and Maintenance
Usage Notices
23
Maintenance
23
FAQ
Settings
Enter Setup State
Delay Arm
FAQ
24
9
10
Speed SOS Dial
11
Keyboard Clicks
12
Disarm by RFID Tag
13-14
Power Saving Mode
15
Change User Code
16
Change Admin Code
17
Reset
18
Instructions of Wired Cables Interface
Instructions of Wired Cables Interface
25
Technical Specifications
Technical Specifications
26
Foreword
Parts List
Thank you for purchasing this wireless keypad. It is
recommended to install outside the entry door and users can
achieve operations such as arm, disarm, stay mode after
inputting passcode. Moreover, the keypad can connect with
an electronic door lock to work as an access control system
for homes and offices. When users are leaving rooms, just
close the door, the electronic lock will be locked
automatically. Before entering house, just input the passcode
and then press [Disarm] key or put RFID tag purchased
separately close to the RFID reader to disarm the system. By
this way, the door will be opened easily, which is very
convenient.
Keypad x 1
A
AA
A
AA
AAA
1
AAA 1.5V battery x 3
Screw x 4
Manual x 1
Wired Cables x 1
2
Appearance
Positive and
negative
terminals
for battery
AAA
+
+
Battery slot
LED Indicator
Tamper Switch
RFID reader
Wired Cables
Interface
Arm
Disarm
Stay mode
SOS key
RFID wake-up key
Rear cover
+
+
RFID tag / card (125KHz) can be purchased separately.
Max. 50 pcs are supported.
RFID Tag
3
+
4
Preparation before Use
Connect Keypad to Control Panel
Make sure the control panel is in connecting state, input user
code or admin code on keypad, and then press any key of
Power on
[Arm] [Disarm] [Stay Mode]. The connection succeeds after
1. Keypad uses 3pcs of AAA batteries.
①
Loose the screw, open the case
②
Put in batteries according to the positive and negative signs
③
Close the rear cover and screw on
one beep.
User can remotely control the panel via the keypad after connection.
(To know connection steps, please consult the panel’s manual.)
AAA
+
+
Connect Keypad with RFID Tag
1. Input [admin code + #] to wake up keypad.
Three beeps mean wrong input.
Remove the insulating strip for first time.
Wrong input for 6 times continuously, the keypad will be locked for 20 seconds.
Note! Open the rear cover of keypad will trigger tamper switch, please
dismiss the alarm by following the disarm instruction in page 20.
2. When connected with electronic door lock as an access control,
keypad is suggested to use the specific power supply for access
control.
To know connection steps, please refer to the instruction manual of electronic
door lock. The electronic door lock and specific power supply for access control
5
should be purchased respectively.
Default admin code: 123456
6
2. Press [9], one beep is heard and the LED indicator is on.
Keypad enters the learning state.
Connect Electronic Door Lock
To know connection steps, please refer to the instruction
manual of electronic door lock.
Installation
Fix the keypad on the door frame or the wall before use.
① Loose the screw, open the case
② Fix the rear cover on the door frame or the wall by screws
3. Put RFID tag close to the RFID reader, the connection
succeeds after one beep and the LED indicator goes out.
③ Fasten the front cover of keypad on the rear cover. Secure two
covers into place
④ Screw on
If two beeps are heard, it indicates the RFID tag has been connected before.
To clear the connection of RFID tags, input [admin code + #] to wake up the
keypad and then press down [9] for six seconds. RFID tags are all cleared after
one beep.
Note! Opening the rear cover of keypad will trigger tamper switch,
please disarm the alarm by following the disarm instruction in page 20.
7
8
Settings
The keypad should enter setup state before all settings.
Delay Arm
When the alarm system is armed, detectors will start working
immediately. At that time, if you still stay at home, it will
trigger an alarm. After setting delay arm, press [Arm] on the
Enter Setup State
keypad, the arm signal will be sent to the control panel after
Input [admin code + #] to wake up keypad.
the set time.
This setting does not apply to Stay Mode.
If both control panel and keypad are set delay time respectively, the actual
delay time is the total of both times.
Delay Arm
Press [3] to enter setup state, the LED indicator is on.
Enter setup state, input:
Under setup state, if there is no operation within 10 seconds, the keypad will
10 seconds, the setup is successful.
2
delay time
When one beep is heard and the LED indicator keeps on for
exit setup state automatically. You can also press [#] to exit.
Once the delay time is set, when you arm the keypad, it will beep once
every two seconds to remind you to leave. The reminding rhythm will
Default admin code: 123456
speed up in the last 15 seconds. After the delay time, the control panel
enters arm state.
Note! User can input digital 0-250 which refers to 0-250 seconds.
Default setting: 0, no delay.
9
10
Keyboard Clicks
Speed SOS Dial
User can choose to enable or disable speed SOS dial. If speed
Keyboard clicks can be turned on or off.
SOS dial is enabled, the control panel will alarm immediately
If it is off, the successful setup tone will be closed too.
when user holds the [SOS] key for 3 seconds. If it is disabled,
user needs to input user code or admin code before holding
the SOS key for 3 seconds. This function is to prevent false
Turn off Keyboard Clicks
operation or trick.
Enter setup state, input:
4
0
Disable Speed SOS Dial
Enter setup state, input:
3
0
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
Turn on Keyboard Clicks
Enter setup state, input:
4
1
Enable Speed SOS Dial
Enter setup state, input:
3
1
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
When one beep is heard and the LED indicator keeps on for
Note! Default setting: 1, turn on the keyboard clicks.
10 seconds, the setup is successful.
11
Note! Default setting: 0, speed SOS dial is disabled.
12
Disarm by RFID tag
Disarming Silently by RFID Tag
User can enable or disable the function of disarming by RFID
tag, or disarming silently by RFID tag.
The control panel and siren will hoot twice when disarming
by RFID tag. If set disarming silently by RFID tag, the control
panel and siren will keep silent to finish disarming without
disturbing neighborhood.
Enable Disarming by RFID Tag
Enter setup state, input:
5
0
Enter setup state, input:
5
2
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
Disable Disarming by RFID Tag
Enter setup state, input:
5
1
Note! Default setting: 1, turn on disarm by RFID tag and the siren will
hoot when disarming.
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
13
14
Power Saving Mode
When one beep is heard and the LED indicator keeps on for
If the keypad is powered by batteries, power saving mode is
10 seconds, the setup is successful.
recommended. In power saving mode, the keypad is in
sleeping status when standby, user needs to press [*] to wake
up the keypad and then put RFID tag close to the reader to
Note! Default setting: 0, turn on power saving mode. User needs to
press [*] to wake up the keypad and then put RFID tag close to the
reader to disarm or unlock the door.
disarm or unlock the door.
Turn on Power Saving Mode
Enter setup state, input:
7
0
Change User Code
Using user code can wake up keypad, open electronic door
lock, or send Arm, Disarm, Stay Mode commands to the
control panel.
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
Turn off Power Saving Mode
To avoid passcode reveal, please change user code when first time use.
Change User Code
Enter setup state, input:
8
new user code
If the keypad is powered by DC 12V power, normal mode is
recommended. User can disarm the system by RFID tag
directly, which is more convenient.
Enter setup state, input:
7
1
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
Note! User code is 4 digits; default code is “1234”.
15
16
Change Admin Code
Reset
Using admin code can wake up keypad, send Arm, Disarm,
After reset, the user code, admin code, and other settings will
Stay Mode commands to the control panel, and also change
restore to default except that the connected RFID tags can
any settings of the keypad.
still disarm and open electronic door lock.
To avoid passcode reveal, please change admin code for first
Enter setup state, input:
0
time.
Change Admin Code
Enter setup state, input:
9
new admin code
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
When one beep is heard and the LED indicator keeps on for
10 seconds, the setup is successful.
Note! Admin code is 6 digits; default code is “123456”.
17
18
Usage
Disarm
The keypad can be used as a remote control. User code or
Users can disarm alarm system by using keypad or by using
admin code should be input before the operation of Arm,
RFID tags.
Disarm, Stay Mode, and Mute Mode.
Using Keypad to Disarm
Arm
Input user code or admin code, and press [Disarm] key, the
LED indicator flashes once and the keypad beeps once and
Input user code or admin code, and press [Arm] key, the
sends Disarm command to the control panel.
LED indicator flashes once and the keypad beeps once and
sends Arm command to the control panel.
When the alarm panel receives the signal, the siren will beep
twice and the Disarm indicator will light on, the alarm system
When the alarm panel receives the signal, the siren will beep
enters disarmed state. In this state, the sensors being
once and the Arm indicator will light on. The alarm system
triggered will not cause an alarm.
enters armed state.
Using RFID Tag to Disarm
If there is an intrusion, the alarm system will be triggered, the
siren will hoot and the control panel will send SMS and auto
dial to pre-stored phone numbers to notify users. (SMS
notification is applicable only for GSM alarm systems.)
In power saving mode, user needs to press [*] to wake up the
keypad and then put RFID tag close to the reader to disarm or
unlock the door.
In non power saving mode,
user can put RFID tag close
to the reader to disarm or
19
unlock the door directly.
20
Stay Mode
Emergency Call
Input user code or admin code, and press [Stay Mode] key,
When the keypad is in Speed SOS Dial mode, user just holds
the LED indicator flashes once and the keypad beeps once
the [SOS] key for 3 seconds, the LED indicator flashes once,
and sends Stay Mode command to the control panel.
the keypad beeps once, and the control panel alarms
immediately.
When the alarm panel receives the signal, the siren will beep
once and the Stay Mode indicator will light on, the alarm
system enters stay mode state.
When the keypad is not in Speed SOS Dial mode, user needs
to input user code or admin code before holding the [SOS]
key for 3 seconds to send an alarm.
All the sensors in other zones are armed to prevent the
intruder except that the motion detector in Home Mode Zone
is disarmed, so that people can move freely at home.
Mute Mode
Mute mode means that the LED indicators of control panel
flash, but the siren does not beep, to avoid disturbing the
neighborhood.
Input user code or admin code, and hold any key of [Arm]
[Disarm] [Stay Mode] for 2 seconds, the LED indicator
flashes once, the keypad beeps once and sends
corresponding command to the control panel.
Home Mode Zone
(Jumpers setting for accessories)
When the alarm panel receives
the signal, the LED indicator
lights on or off, but the siren
does not beep.
21
22
Care and Maintenance
In order to avoid any harm to the users or others during
usage and prolong the usage life, please abide by the
following notices.
FAQ
Problem
Usage Notices
General instruction
The keypad should be connected to control panel before use.
No response
from keypad
The power supply of keypad will probably impact on the transmitting distance
of wireless signal.
The keypad can be powered by 3 pcs of AAA batteries, or wired by DC 12V.
The keypad is compatible for any our alarm system.
Please remove the battery insulating strip before use.
Keypad
cannot
connect to
control panel
Do not press SOS key if there's no emergency to avoid disturbing the
neighborhood.
Check the keypad regularly to ensure the system works properly in case of
emergency.
The keypad is neither waterproof nor moisture-proof, please install it in a
shady, cool and dry place.
No response
from the
control panel
by operating
on keypad
Cause
Low battery
Please change the battery
The positive and
negative terminals
are reversed
Follow the right terminal direction and
inert the battery again
Keypad is locked by
inputting wrong
passcode continually
more than 6 times
Keypad will be unlocked after
non-operation for 20 seconds
No response from
alarm panel
The keypad is non explosion-proof. Please keep it away from fire, flame sources.
Install the keypad away from objects such as heater, air conditioner,
microwave oven etc. that produces heat or electric-magnetic.
Forbiddance of decomposition
Take the keypad for disposal of recycling according to the local regulation.
Do not take apart the product if you are not a professional technician.
Maintenance
23
You can get most dust or fingerprint off with a dry, soft cloth
or tissue. If there is dirt on the keypad, please wipe the
surface by a soft cloth with a little dilute alkaline detergent
and then wipe again with a dry cloth.
Cannot
disarm by
RFID Tags
Keypad
cannot be
programmed
Keypad
cannot be
armed,
disarmed and
in stay mode
Make sure the alarm panel is
powered on
Make sure the alarm panel enters
learning state
Alarm panel beeps
twice
Keypad has been learned
Keypad is not learned
to control panel
Please connect the keypad to the
control panel by following the manual
instruction
Distance between
keypad and control
panel is too far
The case of keypad is made of ABS. Please keep it away from strong light to
ensure the lifetime.
Forbiddance
Solution
Please move the keypad in a proper
distance where control panel can
receive the signal of keypad
It’s recommended to buy signal
repeater to extend the distance
The RFID tags are not
learned to keypad
Please connect the RFID tag to
control panel by following the
manual instruction
Disarm by RFID tag
function is deactivated.
Enter setup state and activate the
function of disarm by RFID tag
Keypad is in power
saving mode
Disarm after pressing [*] key
Keypad is not waked
up
Please input [admin code+#] to wake
up the keypad
Keypad doesn’t enter
setup state
Please input [admin code+#], and
press [3] to enter setup state
Haven't input user
code or admin code
before operation
Please input the user code or admin
code before operation
24
Instructions of Wired Cables
Interface (from Left to Right)
+12V (RED WIRE):
Positive of power
GND (BLACK WIRE):
Negative of power
PUSH (YELLOW WIRE):
Signal output for electronic lock
GND (WHITE WIRE):
Negative of power
OPEN (GREEN WIRE):
Signal input for exit switch
25
Technical Specifications
Product Name:
Keypad
Model No.:
KP-700
Power Supply:
3 pcs of AAA batteries or DC 12V
Static Current:
≤ 3uA (powered by batteries)
Transmitting Current:
≤ 10mA
RFID Tags Supported:
50pcs
Transmitting Distance:
≤ 80m ( in open area)
Radio Frequency:
315MHz or 433MHz
Housing Material:
ABS plastic
Operating Temperature:
-10℃~55℃
Relative Humidity:
≤ 80%RH (non-condensing)
Dimensions:
135 x 90 x 15mm
Net Weight:
90g
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement