Bissell | ProHeat 2X-EX9200 | User`s guide | Bissell ProHeat 2X-EX9200 User`s guide

Bissell ProHeat 2X-EX9200 User`s guide
USER’S GUIDE
9200, 9400 SERIES 220-240V
3
Safety Instructions
4-5 Product View
6
Assembly
7-11 Features/Operation
12-19 Maintenance and Care
19-20 Troubleshooting
21 Consumer Services
22-23 Replacement Parts
24 Warranty
IMPoRTanT SafETy InSTRUcTIonS
When using an electrical appliance, basic
precautions should be observed, including
the following:
REaD aLL InSTRUcTIonS
BEfoRE USInG yoUR
UPRIGHT DEEP cLEanER.
Always connect to a properly Earthed
outlet. Unplug from outlet when not in
use and before conducting
maintenance or troubleshooting.
WaRnInG:
To reduce the
risk of fire, electric shock, or injury:
■ Use indoors only
■ Do not immerse
■ Use only on surfaces moistened by
cleaning process
■ Do not leave machine when it is plugged in
■ Do not service machine when it is plugged in
■ If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent in order
to avoid a hazard
■ Do not use machine if it has been dropped,
damaged, left outdoors or dropped into water
■ Do not expose to rain, store indoors
■ Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around sharp
corners or edges, run appliance over cord, or
expose cord to heated surfaces
■ Do not carry the appliance while in use
■ Do not unplug by pulling on cord; unplug by
grasping plug not the cord
■ Do not handle plug or appliance with wet hands
■ Do not put any object into appliance openings, use
with blocked opening or restrict air flow
■ Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts
■ Do not pick up hot or burning objects
■ Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc.) or use
in the presence of explosive liquids or vapours
■ Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint
thinner, some moth proofing substances,
flammable dust, or other explosive or toxic vapours
■ Remove plug from electrical outlet before cleaning
or maintaining the appliance
■ Not intended for use by young children or infirm
persons without supervision
■ Young children should be supervised to ensure
that they do not play with the appliance
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, petrol, etc.)
■ Do not modify the Earthed plug
■ Do not allow to be used as a toy
■ Do not use for any purpose other than described
in this User’s Guide
■ Use only manufacturer’s recommended
attachments
■ Use only cleaning products formulated by
BISSELL for use in this appliance to prevent
internal component damage
■ Keep openings free of dust, lint, hair, etc.
■ Keep appliance on a level surface
■ Turn off all controls before unplugging
■ Be extra careful when cleaning stairs
■ Pay close attention when working
around children
SaVE THESE
InSTRUcTIonS.
ThIS moDEL IS foR hoUSEhoLD USE oNLY.
WaRnInG:
This appliance must
be Earthed.
IMPoRTanT
foR oPERATIoN oN
A 220-240 VoLT A.C. 50/60 hz PoWER
SUPPLY oNLY.
If your appliance is fitted with a nonrewireable
BS 1363 plug it must not be used unless a 13
amp (ASTA approved to BS 1362) fuse is fitted in
the carrier contained in the plug. Spares may be
obtained from your BISSELL supplier. If for any
reason the plug is cut off, it must be disposed
of, as it is an electric shock hazard should it be
inserted into a 13 amp socket.
Product view
Spray Trigger
Power Switch
Heater Switch
Extra Long
Power Cord
Flex Hose
Upper Handle
Easy Carry Handle
Heat
Indicator Light
Tank Carry
Handle
Ready Tool
Dial™
Detent Pedal
2-in-1
Water Tank
Lower Base
Edge Sweep Brushes
Easy To Remove
Nozzle
optional accessories:
These items are available for purchase. To order replacement parts, additional tools or formulas, please refer to page 22-23.
3” Tough Stain Brush
4” Upholstery Tool
Spraying Crevice Tool
6' Stair Tool
TurboBrush™
Scotchgard™ Protector Applicator
Hard Floor Attachment
Product view
Spray Trigger
Upper Hose Rack
Hose Secure
Latch
Upper Handle
TurboBrush™
Storage
(select models)
Crevice Tool Holder
(select models)
Lower Hose Rack
Lower Base
Keep plenty of genuine BISSELL
deep cleaning formulas on hand
so you can clean whenever it
fits your schedule. always use
genuine BISSELL deep cleaning
formulas. non-BISSELL cleaning
formulas may harm the machine
and void the warranty.
Detent Pedal
Formula Tank
BISSELL formulas:
These items are available for purchase. To order replacement parts, additional tools or formulas, please refer to page 22-23.
1.42 L
Fibre Cleansing
Formula™ with
Scotchgard™
protector
1.42 L
Multi- Allergen
Removal™ Formula
with Scotchgard™
protector
1.42 L
Pet Odor and Soil
Removal™ Formula
with Scotchgard™
protector
1.42 L
Natural Orange
Extract Formula with
Scotchgard™ protector
1.42 L
Lavender Essence
Formula with
Scotchgard™
protector
32 oz.
Hard Floor
Solutions™
Formula
8 oz.
Scotchgard
Protector Post
Treatment
Cartridge
How to put it together
This user’s guide has been designed to help you
get the most satisfaction from your BISSELL
ProHeat 2X. you’ll find assembly and operating
instructions, safety precautions, as well as
maintenance and troubleshooting instructions.
Please read this user's guide thoroughly before
assembling your deep cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate
and organize all parts before assembly. familiarize
yourself with the parts and where they go.
following this user’s guide will greatly enhance
your ability to get the most performance from your
BISSELL ProHeat 2X for many years.
WaRnInG:
Do not plug in your
cleaner until you have
completely assembled it per
the following instructions
and are familiar with all
instructions and operating
procedures.
1.
2.
3.
4.
Assembly
Your ProHeat 2X comes in three, easy to
assemble components:
Upper Handle
Lower Handle
Tool Caddy
The only thing you will need to assemble your
cleaner is a Phillips head
screwdriver.
Refer to assembly Diagram on page 5
1. Slide upper handle onto lower handle.
2.
Screw 3 screws into the marked holes.
3.
Place upper hose rack onto back of upper
handle and secure with tapered screw.
4.
5.
Crevice Tool
Holder
(select models)
(select
Place lower hose rack onto back of upper models)
handle by pushing in and sliding down until
it snaps into place.
Scotchgard
Protector
Applicator Tool
5.
Snap tools into the tool caddy as shown in
figure 5.
6.
Wrap power cord and flex hose as shown in (select models)
figure 6.
7.
Keep flex hose snugly in place by using
the hose secure latch.
ProHeat 2X assembly is now complete.
Tough
Stain Brush
TurboBrush
6.
Spraying
Crevice Tool
(select models)
Special features
your BISSELL ProHeat 2X deep cleaner is a home
cleaning system that uses the power of heat,
brushes and cleaning formula to get the deep
down dirt for a maximum clean. not only does it
come with a lot of unique features, it has been
designed with you, the customer, in mind.
Built-in heater
BISSELL ProHeat models all feature a patented
built-in heater which will heat the hand hot tap
water you put in up to 25 degrees hotter to safely
optimize cleaning effectiveness. The heater
will never allow the temperature to exceed 190
degrees. The heater switch on the front of the
machine controls the heater so you have the
option to turn off the heat if you are cleaning
delicate wool or oriental rugs.
Dual DirtLifter PowerBrush
The two DirtLifter PowerBrush rolls are
designed to enhance cleaning performance.
The bristle pattern safely lifts out the deep
down dirt while gently grooming carpet fibres.
The floating suspension self-adjusts to all
carpet heights and protects your carpet if
you leave the power switch on (I). once the
product is in the upright position, the brushes
automatically stop spinning. The detent pedal
will activate the brushes when floor cleaning.
(located behind 2-in-1 water tank)
Custom Clean™
The custom clean feature automatically mixes
hand hot tap water with the BISSELL formula.
Simply choose one of the 4 settings (heavy
traffic, normal clean, light clean, or rinse) and
the ProHeat 2X will adjust the right amount of
cleaning formula to mix with the heated water
to fit your cleaning need.
This feature is available on all ProHeat 2X
models, either behind the 2-in-1 water tank or on
the upper handle.
Having a separate formula tank from the 2-in-1
water tank also allows no waste of formula.
Because the water and formula are stored
separately, they are not mixed until you are ready
to clean. When your cleaning job is finished,
the formula can be stored ready to use in your
machine for the next time!
oR
(located on upper handle)
Special features
Scotchgard Protector Applicator Tool and Scotchgard Warranty
carpet protection applied at the mill typically
wears down with heavy foot traffic over time and
with everyday cleaning, including deep cleaning.
To help restore this important protection, BISSELL
offers deep cleaning formulas with Scotchgard
protector and a post-applicator to apply
Scotchgard protector with the same materials
used by carpet mills. This offers extra protection
against dirt and tough stains to keep your carpets
looking good longer.
To maintain your Scotchgard 5-year limited stain
warranty, you no longer are required to hire a
professional cleaner. By using your BISSELL ProHeat
machine with BISSELL formulas containing
Scotchgard protector every 12 months, your carpet
warranty from 3M remains in effect. no other home
deep cleaning system can do this for you. Refer to
the Scotchgard protector warranty for details.
2-in-1 water tank
our 2-in-1 water tank full capacity system is
designed with a heavy duty bladder inside for
clean water. as you clean, the clean water in the
bladder will empty and mix with the cleaning
formula. Dirty water pulled out of your carpets will
collect around the outside of the bladder so that
clean and dirty water are always kept separate.
This allows the user to maximize tank space, yet
only carry one tank to and from the sink for
emptying and filling.
Easy to remove and clean nozzle
now, cleaning up your machine after the
cleaning process is easier than ever! Simply
remove the 2-in-1 water tank and remove the
screw to pop out the nozzle for rinsing in the
sink. Dirt, loose carpet fibres and remaining pet
hair or fuzz gets washed away in a snap.
Ready tools dial
now, cleaning up your machine after the
cleaning process is easier than ever! Simply
remove the 2-in-1 water tank and remove the
screw to pop out the nozzle for rinsing in the
sink. Dirt, loose carpet fibres and remaining pet
hair or fuzz gets washed away in a snap.
HOSE
F
CL LOOR G
EANIN
Operation
BRUSH
SUCTION
2.
Move furniture to another area if cleaning an
entire room (optional).
3.
Vacuum area with a dry vacuum cleaner
thoroughly before deep cleaning.
4.
Plan your cleaning route to leave an exit
path. It is best to begin cleaning in the
corner farthest from your exit.
5
fill the 2-in-1 water tank. Remove the tank
from the base of the machine by lifting up
the tank carry handle. Carry like a bucket to
the sink.
3'
1
2
3
4
aTTEnTIon:
Some Berber carpets have a
tendency to fuzz with wear.
Repeated strokes in the same
area with an ordinary vacuum
or deep cleaner may aggravate
this condition. Please see Stain
Removal instructions on page 16.
Carpet cleaning
1.
8
7
6
E
Plan activities to give your carpet time to dry.
9
10
11
12
S
HT
1.
EXIT
A
4' ER RT
Before you clean carpets
1.
1a.
1b.
1c.
1a. Unlatch the top of the tank from the
bottom by lifting up on the tank latch which
is located on the back of the tank.
1b. Remove the top of the tank by lifting up on
the handle.
note how the lip on the top tank separates
from the groove in the bottom tank. This
placement is important when putting the
tank back together.
1c. Fill the heavy duty bladder with clean hand
hot tap water.
*Do not boil or microwave water as it can
destroy the bladder.
1d. Leaving the filled bottom of the tank on a flat
surface, only maneuver the top of the tank.
To attach the top part of the tank to the
bottom, carefully hook the lip on the top tank
into the groove on the bottom tank.
1d.
Lip
1e. Fasten tanks together by securing the latch
in the back.
Groove
(underside of
bottom tank)
note: Remember to secure the tank latch in
the back and test to make sure it is secure
before picking up the tank.
1e.
Operation
Carpet cleaning continued
2.
2.
fill the formula tank. Fill up the formula tank
by first unscrewing the cap and insert. Always
use genuine BISSELL formulas to maximize
cleaning and for the safety of your machine.
Fill formula up to the line and replace the cap
and insert. Place formula tank into the slot in
the back of the machine for a snug fit.
3.
Set custom clean dial. Simply choose one of
the 4 settings (heavy traffic, normal clean, light
clean, or rinse) and the ProHeat 2X will adjust
the right amount of cleaning formula to mix
with the heated water to fit your cleaning need.
4.
Set Ready Tools dial to the floor cleaning setting.
5.
Plug into a proper outlet and turn the power and 4.
heater switches to the on (I) position. Allow one
minute for the built-in heater to warm-up before
cleaning. The ProHeat 2X will be fully warmed and
will provide optimal performance after one minute of
continuous heated cleaning.
6.
cleaning strokes. While pressing the spray
trigger, make one slow forward wet pass and
another one back. Let the built-in heater, formula,
and DirtLifter PowerBrushes do the work for you.
caution: Do not overwet. Take care not to run
over loose objects or edges of area rugs. Stalling
the brush may result in premature belt failure.
note: your machine is equipped with a
circuit breaker that will automatically shut
off the brush if a large or loose object is
caught in the brush roll. If that happens, be
sure to unplug your machine, remove the
foreign object, and then plug the machine
back in to reset the circuit breaker.
Release the spray trigger and make one
slow forward and backward pass over the
same area to remove any residual dirty
water and aid in drying. Repeat cleaning
passes until water being pulled up appears
clean. Continue passes without pressing the
spray trigger until you can’t see any more
water being pulled up. After cleaning, you
may want to turn the Custom Clean dial to
rinse to give your carpeting a final water
only rinse. This will ensure thorough removal
of embedded dirt loosened by the formula.
BISSELL deep cleaning formulas contain an
anti-resoiling agent that helps your carpets
repel dirt and keeps them looking
good longer.
2a.
3.
oR
5.
HOSE
F
CL LOOR G
EANIN
Power Switch
Heater Switch
WaRnInG:
To reduce the risk of fire and
electric shock due to internal
component damage, use only
BISSELL deep cleaning formulas
intended for use with the deep
cleaner.
Keep plenty of genuine BISSELL deep
cleaning formula and Scotchgard™
protector cartridges on hand so you can
clean and protect whenever it fits your
schedule. always use genuine BISSELL
deep cleaning formulas. non-BISSELL
cleaning formulas may harm the
machine and void the warranty.
Operation
Carpet cleaning continued
7.
7.
7a.
7b.
7c.
7d.
7e.
7f.
7g.
Remove the tank from the base of the machine
by lifting up on the tank carry handle. Carry like
a bucket to a utility sink or outside where you
will dispose of the dirty water.
7a. Unlatch the top of the tank from the
bottom by lifting up on the tank latch which
is located on the back of the tank.
7b. Remove the top of the tank by lifting up on
the handle.
note how the lip on the top tank separates
from the groove in the bottom tank. This
placement is important when putting the
tank back together.
7c. Lift the bottom portion of the tank and pour out
dirty water toward the sink through the triangular
shaped opening in the corner of the tank.
note: you may notice hair & debris deposits on
the carpet or in the tank that were loosened by
the cleaning action (especially with newer carpets
that have never been deep cleaned before). This
debris should be picked up and thrown away.
7d. Fill the heavy duty bladder with clean hand
hot tap water, following instructions page 9.
note: Remember to secure the tank latch in
the back and test to make sure it is secure
before picking up the tank. always check
the level of cleaning formula in the formula
tank at the same time and refill as needed.
8.
Rinse (optional). Rinsing is an optional
step that can be done during the cleaning
process by switching from one of the clean
settings on the Custom Clean dial to a rinse
setting, or it can be done after the carpeted
area has been cleaned. Simply choose the
rinse setting on the Custom Clean dial,
and follow the same path as you did for
cleaning, taking care to do a forward (wet)
stroke by depressing the spray trigger, a
backward (wet) stroke, and a forward and
backward (dry) stroke, releasing the spray
trigger. Continue this until the water you see
coming up the nozzle is clear.
8a.
or
Maintenance and care
Machine storage
WaRnInG:
once your cleaning is complete, make sure the
2-in-1 water tank is emptied, rinsed out, and
dried before the next use. The formula tank
can remain filled and ready to go, or it can
simply be emptied back into the formula bottle
if that is more convenient.
note: Store cleaner in a protected, dry
area. Since this product uses water, it must
not be stored where there is a danger of
freezing. freezing will damage internal
components and void the warranty.
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
3.
Filter
Machine care
for best results, a few simple steps can assure
your machine is well maintained after your
cleaning is complete.
1. Turn power and heater switches OFF (O).
Unplug the machine and wrap the power cord.
2.
After emptying the 2-in-1 water tank, rinse
it out at a faucet with running hand hot tap
water, taking care to clean underneath the
heavy duty bladder and all around it.
3.
The top half of the tank can be rinsed clean
through the nozzle area. Also, pop out the red
filter underneath the top half of the tank and
rinse that out. Replace before putting the top
and bottom halves of the tank together.
4.
Before you place the cleaned 2-in-1 water tank
back onto the machine, simply unscrew the
nozzle using a Phillips head screwdriver .
This can be rinsed out at the faucet. Then
replace back onto the machine by starting
from the bottom of the nozzle and hooking the
tabs into the holes on the bottom sides of the
machine. Secure into place with the screw.
5.
The inside of the end caps by the brush rolls
can be wiped out with a clean paper towel,
or, if a more thorough cleaning is desired, the
end caps can be taken off using a Phillips
head
screwdriver and rinsed clean.
Replace after cleaning.
6.
Any loose hair or debris can be pulled from the
brush rolls and thrown away. For the most
thorough clean before storage, follow directions
on pages 18 & 19 for removal and replacement
of the brush rolls and belts.
Tip:
Let all parts dry completely
before storing
WaRnInG:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
Maintenance and care
Machine care continued
7.
To clean attachments that may have been used,
remove from hose and rinse in clean, running water.
Dry and replace attachment in the tool caddy. Clean
the flex hose by suctioning clean water from the tap.
Before replacing, lift end of flex hose and stretch out
to ensure all water is cleared from flex hose. Refer to
page 15, illustrations 9 & 10.
8.
After carpet is dry, vacuum again to remove
hair and fuzz.
Post-treatment Scotchgard Protector* (optional)
Some models are equipped with a Scotchgard
protector post-treatment applicator and cartridge.
Using this, along with one of the BISSELL deep
cleaning formulas containing Scotchgard, to help
retain the carpet cleanliness achieved with the
ProHeat 2X machine. for best results, the post
cleaning treatment should be applied while the carpet
is still damp. It is recommended that the Scotchgard
protector be applied every 12 months to all clean
carpeted areas, and after every deep cleaning for high
traffic areas such as entryways and stairs.
1. Immediately after cleaning and rinsing your
carpets, empty the 2-in-1 water tank and refill the
heavy duty bladder with clean hand hot tap water.
2.
3.
4.
5.
6.
Set Ready Tools dial to the hose/attachment setting.
Purge the hose to eliminate cleaning formula
from the tube by spraying clean water through
the flex hose (without attachments) into a sink
for 15-30 seconds.
Attach Scotchgard protector post-treatment
cartridge to the applicator tool, following the
instructions on the cartridge. Attach the combined
tool/cartridge to the flex hose. The water from the
2-in-1 water tank will automatically mix with the
concentrated Scotchgard protector post-treatment
formula contained in the cartridge.
Turn the Custom Clean dial to the rinse/
protect setting.
Before applying Scotchgard protector to
a large area, test in a small, hidden area
for colourfastness. Examine area when
dry. If colour is affected, do not use. For
use on upholstery, look for manufacturer’s
cleanability code tag. Use only on fabrics
coded “W” or “WS”. If coded “S” or “X”, do
not use. Not recommended for use on velvet,
silk vinyl, leather, or 100% cotton upholstery.
3.
4.
Tip:
If clogged, soak
applicator tool
in hand hot tap
water before
using.
Maintenance and care
Post-treatment Scotchgard Protector* (optional) continued
7.
Apply Scotchgard protector in a slow
sweeping motion with a slight overlap of the
treated area. For best coverage, follow the
guide on the cartridge.
8. One 8 oz. cartridge protects 200 square feet
(18.6 sq. meters). This is equal to two average
size rooms, (each at 10 x 10 ft. or 3 x 3 meters).
Periodically check the level in the bottle to
ensure the best coverage.
9. Be careful not to spray the Scotchgard
protector onto furniture or fabric that has not
been tested for colourfastness. If this does
occur, wipe off the Scotchgard protector.
10. When finished remove the cartridge from the
applicator tool. If formula is left, replace the cap
to the cartridge and store at room temperature
for later use.
11. With the applicator tool still on the end of the
flex hose, spray clean hand hot tap water into
the sink to avoid any future clogging. Let dry
before storing.
12. Store applicator tool in a convenient location
for use the next time.
7.
11.
Cleaning with attachments
bvh
g kvh
gh j j h
d b lg
fd hn l kl
sd jkn f h
Ad bj jh
b j
cv hh
gcg
your ProHeat 2X machine comes equipped with
a flex hose and at least one cleaning tool for
cleaning stairs, upholstery, and more.
1. Important! If using to clean upholstery, check
upholstery tags.
a. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can
use your ProHeat 2X. If the tag is coded
with an “X” or an “S” (with a diagonal
stripe through it), or says “Dry Clean
Only”, do not proceed with any deep
cleaning machine. Do not use on Velvet or
Silk. If manufacturer’s tag is missing or not
coded, check with your furniture dealer.
b. Check for colourfastness in an
inconspicuous place.
c. If possible, check upholstery stuffing.
Coloured stuffing may bleed through
fabric when wet.
d. Plan activities to allow upholstery time to dry.
e. Vacuum thoroughly to pick up loose debris
and pet hair. Use a vacuum with a brush
attachment and a crevice tool to clean in
fabric folds.
Manufacturer’s tag
WaRnInG:
To reduce the risk of
injury, be extra careful
when cleaning stairs.
Make sure machine is
secure and level.
Maintenance and care
Cleaning with attachments continued
2.
Follow the instructions on pages 9 & 10 for filling the
2-in-1 water tank and the formula tank.
3.
Set Ready Tools dial to the hose attachments setting.
This will allow spray and suction from the flex hose.
4.
Set Custom Clean dial for heavy traffic, normal
clean, light clean, or rinse, as desired
5.
Attach the cleaning tool to the end of the hose.
6.
Plug in and turn on the power switch.
5.
note: The built-in heater heats the cleaning
formula for carpet and hard floor application only.
It does not heat the cleaning formula through the
accessory tools.
7.
Clean by pressing the spray trigger to spray formula
onto the area to be cleaned. Slowly move the tool
back and forth over the soiled surface. Release the
spray trigger to suction soiled water. Continue to clean
in the area, working in small sections, until no more
dirt can be removed. Rinse (optional) and suction as
needed. caution: Do no overwet.
8.
Remove and rinse tools in clean, running water.
Dry and replace in the tool caddy.
9.
It is recommended that you suction clean water
from the tap to rinse out the flex hose.
10. Before replacing, lift end of flex hose and stretch out
to ensure all water is cleared from flex hose.
11. Coil flex hose around the tool caddy.
12. Empty 2-in-1 water tank and rinse out,
following the instructions on page 11.
13. Return Ready Tools dial to floor setting.
Cleaning formula section
Keep plenty of genuine BISSELL advanced deep cleaning
formula for full size machines on hand so you can clean
and protect whenever it fits your schedule. always use
genuine BISSELL deep cleaning formulas.
1.42 L
Fibre Cleansing
Formula™ with
Scotchgard™
protector
1.42 L
Multi- Allergen
Removal™ Formula
with Scotchgard™
protector
1.42 L
Pet Odor and Soil
Removal™ Formula
with Scotchgard™
protector
1.42 L
Natural Orange
Extract Formula with
Scotchgard™ protector
9.
10.
WaRnInG:
To reduce the risk of fire
and electric Shock due to
internal component
damage, use only BISSELL
deep cleaning formulas
intended for use with the
deep cleaner. non-BISSELL
cleaning solutions may
harm the machine and void
the warranty.
1.42 L
Lavender Essence
Formula with
Scotchgard™
protector
32 oz.
Hard Floor
Solutions™
Formula
8 oz.
Scotchgard
Protector Post
Treatment
Cartridge
Maintenance and care
Stain removal
Do not delay! attending to an accident soon
after it occurs ensures the most optimal clean.
Leaving it for an extended period of time may
cause it to set and become permanent.
1. Blot up liquids with an absorbent cloth
or paper towels. White materials are
recommended because certain dyes may
bleed and make the stain worse.
2.
Gently scrape up any semi-solids with a
spoon or spatula. Do not use a knife or other
utensil with sharp edges because it could
damage the carpet or upholstery.
3.
If the area has dried, remove the remaining semisolids and residue with a sweeper or vacuum.
4.
Be sure to test any spot removal formulas in an
inconspicuous area first. This is important as
some dyes and materials could be damaged
or discoloured by cleaning formulas. If such a
change should occur, try a different formula or
call a professional.
5.
Use your Proheat 2X as a precleaner. With one
of the tools attached to the flex hose, set the
Ready Tools dial to the hose attachments setting
and the Ready Tools dial to heavy traffic. Spray
the area with cleaning formula and allow the
BISSELL Deep Cleaning Formula to for penetrate
3-5 minutes.
note: If cleaning on Berber carpeting, gently run
your machine over a hidden area. If no fuzzing
occurs, continue cleaning in soiled area.
6.
Once the precleaning is complete, use the
attached tool to gently scrub the stain with
back and forth strokes.
7.
Allow time to dry. Some difficult stains may
require a second treatment.
WaRnInG:
To reduce the risk of
fire and electric
shock due to internal
component damage,
use only BISSELL deep
cleaning formula
intended for use with
the deep cleaner.
non-BISSELL cleaning
formula may harm the
machine and void the
warranty.
Maintenance and care
Hard floor cleaning
your ProHeat 2X model may come with a hard
floor tool and Hard floor Solutions formula. If
not, these products are available for purchase
by contacting the BISSELL consumer Services
department by phone. The hard floor tool
provides effective cleaning for linoleum, vinyl,
and tile floors.
caution: Do not use on unsealed hardwood floors.
1. Vacuum or sweep thoroughly to pick up any
loose debris and pet hair.
2.
Move any furniture, if needed.
3.
Empty any carpet cleaning formula back into
the BISSELL bottle if stored in the formula
tank. Fill formula tank with BISSELL Hard
Floor Solution Formula.
4.
Fill the 2-in-1 water tank with hand hot tap
water and set aside.
5.
Attach the hard floor tool onto the bottom of
the machine by hooking it into the nozzle and
swinging it down until it clicks into place.
6.
Check Ready Tools dial. It should be set on
floor cleaning.
7.
Set the Custom Clean dial to normal clean.
8.
Plug in and turn on the power switch and
heater switch.
9.
Slowly move the machine forward and back
over bare floor surface one time while
depressing spray trigger.
caution: Do not overwet.
10. Repeat the motion without pressing the
spray trigger using the hard floor tool to
squeegee and suction up the dirty water.
11. Allow adequate time for floors to dry.
12. Remove hard floor tool, rinse and dry before storing.
13. If any formula remains in the formula tank,
pour it back into the Hard Floor Solutions
bottle for use the next time.
14. Rinse out the formula tank.
WaRnInG:
To reduce the risk of fire,
electric shock or injury
unplug from outlet before
servicing.
5.
Maintenance and care
Small belt removal and replacement instructions
occasional replacement of one or both belts may
become necessary. If that is needed, please
follow the instructions below.
1. Turn off the machine, and unplug it from
the outlet.
2.
Remove both the 2-in-1 water tank and the
formula tank. Set aside.
3.
Unscrew the nozzle and remove it. Set aside.
4.
Turn the machine on its side. IMPoRTanT:
Make sure that the cord side is down.
5.
Remove the clear end cap by unscrewing
the 2 black screws. Take care not to drop
the screws into the unit.
6.
Remove 1 silver screw.
7.
Remove pivot arm by gently lifting up.
8.
Remove small brush belt.
9.
Replace small brush belt, and reverse steps above.
WaRnInG:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
1.
2.
3.
3a.
4.
5.
6.
7.
8.
9.
Brush removal and large belt replacement instructions
Brushes can be removed for cleaning or
replacement as needed.
1. Follow small belt removal instructions above.
2.
Remove brush rolls by pulling them off of the
metal rods.
3.
Place cleaned or new brush rolls back onto the
rods. Make sure one washer is on each end
of the rollers prior to sliding onto the rod. Be
sure to let the rod slide through the bushing to
insure proper fit.
4.
Re-attach the long belt on the bottom to the
cogs of the small roller brushes.
5.
6.
Place small belt over back roller and metal cog.
Place pivot arm in place and screw in place
using the silver screw.
WaRnInG:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
2.
3.
5.
6.
4.
Maintenance and care
Brush removal and large belt replacement instructions
7.
Re-attach clear end cap by tightening with
the (2) black screws.
8.
Return nozzle to front of unit, by latching from
underneath and then securing with a screw.
If you have any questions or are having
trouble installing or replacing your belt(s)
or brushes, please call BISSELL Consumer
Services in the UK at 0870.225.0109, in
Australia at 1.800.811.183 or in New Zealand
at 0800.247.735. For all other countries call
our U.S.A. Headquarters at 616.453.4451 or
visit the BISSELL Website: www.bissell.com
7.
8.
WaRnInG:
To reduce the risk of fire,
electric shock, or injury,
unplug machine from
outlet before servicing.
Troubleshooting
Built-in heater ready light does not illuminate
Possible cause
Remedies
1. The heater switch is not turned on (I)
2. The power switch is not turned on (I)
1. Turn the heater switch on (I)
2. Both switches must be on (I) to
activate the heater ready light
Reduced spray or no spray
Possible cause
Remedies
1. 2-in-1 water tank may be empty
1. Fill heavy duty bladder with hand hot
tap water
2. Fill formula tank with BISSELL deep
cleaning formula
3. Turn power switch off (O)
remove and reseat 2-in-1 water tank
4. Turn power switch off (O) and
then back on (I). Wait one minute,
then depress spray trigger
2. Formula tank may be empty
3. 2-in-1 water tank may not be
seated completely
4. Pump may have lost prime
DirtLifter PowerBrushes do not turn
Possible cause
Remedies
1. The brush is off or broken
1. Turn power switch off (O) and
unplug unit from outlet. Follow
instructions on pages 18 and 19
2. The unit is in the upright position
2. Brushes only rotate when unit is
reclined using the detent pedal
3. Circuit breaker may have tripped
3. Turn the power switch off (O) and
unplug from outlet. Check to see if
foreign object is caught in brush roll.
remove object. Plug machine back in
to reset circuit breaker
Troubleshooting
Scotchgard protector applicator tool is not spraying
Possible cause
Remedies
1. Cartridge is not connected to the tool
1. Follow instructions on cartridge to
assure proper fit
2. Set Ready Tools dial to hose
attachments setting
3. Soak applicator tool only in hand hot
water. Spray without the cartridge
attached to purge any residual
formula left in the applicator tool
2. Ready Tools dial on floor setting
3. Formula clogging the spray trigger
cleaner not picking up solution
Possible causes
1. Ready Tools dial may be at wrong setting
2. 2-in-1 water tank may not be
seated properly
3. 2-in-1 water tank may not be
assembled properly
4. Formula or 2-in-1 water tank is empty
5. 2-in-1 water tank has picked up
maximum dirty water and red float
door has closed
6. Red float "door" in the tank may have closed
as a result of bumping an object or moving
machine back and forth too quickly
Remedies
1. Set Ready Tools dial to either
floor cleaning or hose
attachments setting
2. Pick up both the 2-in-1 water
tank and formula tank and
reseat them so they fit snugly on
the unit
3. Check to make sure the "lip" of
the nozzle is securely hooked
into the groove on bottom of
2-in-1 water tank (see page 9)
4. Check water levels in heavy duty
bladder and formula tank
5. Empty 2-in-1 water tank. Refill
heavy duty bladder with clean
hand hot tap water and replace
6. Turn the machine off (O),
allowing red float door to release into
the open position. Turn unit back
on (I) to continue cleaning. Be
sure your forward and backward
strokes are done at a slower pace
other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
Replacement parts BISSELL ProHeat 2X
Below is a list of common replacement parts. While not all of these parts may have come
with your specific machine, all are available to you for purchase, if desired.
Item
Part no.
9
10
203-6660
203-6618
11
12
13
14
15
16
17
18
19
203-6601
203-6675
203-6676
203-6677
203-6678
203-6679
203-6680
203-6681
203-6682
20
21
22
23
24
25
26
27
203-6685
203-6686
203-6688
203-6804
203-6689
203-6690
710E
720E
28
730E
29
740E
30
31
32
750E
0484
0464
1
2
3
4
5
6
7
8
203-6651
203-6652
203-6653
203-6654
203-6655
203-6692
203-6691
203-6611
Part name
3” Tough Stain Tool
Powered TurboBrush hand Tool
4” Upholstery Tool
6” Wide Stair Tool
Spraying Crevice Tool
hard floor Tool
Scotchgard Applicator Tool
Grey Tank Assembly (complete) for Black unit (Blue or
Purple complete tank assemblies available upon request)
Grey Tank Lid (Blue or Purple Tank Lids available upon request)
Grey Tank Bottom (Blue or Purple Tank Bottoms available
upon request)
hose Assembly
Cap and Insert for Water Tank
formula Tank (includes Cap & Insert for formula Tank)
Cap and Insert for formula Tank
front Nozzle (includes gasket)
Autoload Gasket (fits both Water and formula Tank)
filter with Door
Water Tank Latch
Cord Wrap (Black) (Blue or Purple cord wrap available
upon request)
Clear End Cap w/Edge Brushes (2 pack, includes screws)
Brush Roll – 6 row (includes 1 brush, axle, 2 swivel arms)
Small Brush Belt (non-cord side)
Large Brush Belt (cord side)
hose Secure Latch
hose Rack Assembly (Top/Bottom hose Rack, Screws)
1.42 L fiber Cleansing formula™ with Scotchgard™ protector
1.42 L multi-Allergen Removal™ formula with
Scotchgard™ protector
1.42 L Pet odor and Soil Removal™ formula with
Scotchgard™ protector
1.42 L Natural orange Extract formula™ with
Scotchgard™ Protector
1.42 L Lavender Essence formula™ with Scotchgard™ protector
32 oz. hard floor Solutions™
Scotchgard Protector Post Treatment Cartridge
*not all parts are included with every model.
Replacement parts BISSELL ProHeat 2X
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising