SeaLand 4 Owner`s manual

SeaLand 4 Owner`s manual
SeaLand
®
Gravity discharge Toilet
Owner’s Manual
SeaLand® 711-M28 Toilet
! WARNING
This manual must be read and understood
before adjustment, maintenance, or service
is performed. Modification of this product
can result in property damage.
1
Table of Contents
Recommendations
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Recommendations . . . . . . . . . . . . . . . . . . . . . . 2
Installation Instructions . . . . . . . . . . . . . . . . 2 - 4
Operating Instructions. . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5
Preparing for Summer Use. . . . . . . . . . . . . . . . 5
Model Identification . . . . . . . . . . . . . . . . . . . . . 5
Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Customer Service . . . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . 6
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . 8
1. Read the “Operating Instructions” section of the
manual carefully.
Specifications
Shipping Information:
5. Do not use chlorine or caustic chemicals, such as
laundry bleach or drain opening types, in the
system. These products damage the seals in
toilets.
Carton Sizes:
6. Do not flush foreign objects through the toilet.
2. Make sure all guests understand the operation of
the SeaLand toilet.
3. Carry a few spare parts for the maintenance purposes. Dometic has developed several repair kits
that will save you both time and expense should a
problem occur. See “Customer Service” section of
this manual.
4. Use only SeaLand brand® Tissue and SeaLand®
brand Holding Tank Deodorants to maintain a
trouble-free system.
Product Name: 711-M28 SeaLand Marine Toilet
Toilet 21" x 18-1/2" x 13-1/2"
(533mm x 470mm x 343mm)
7. Do not allow small problems to go unsolved. As
soon as a problem is detected, correct it.
Tank 19-1/4" x 17-1/2" x 11-1/2"
(489mm x 445mm x 292mm)
Installation Instructions
Weight Approx. 49 lbs. (22Kg)
Tank:
1. Select position in bathroom where unit can operate
properly. Allow room for using the flush lever and
clearance for raising the seat and lid.
System:
Average water consumption per flush 1 Qt. (.95 L)
2. Position the tank 3/4" (19mm) away from the wall.
Mark four holes at mounts on tank base. After holes
are marked, remove tank, and drill pilot holes. Slide
tank back into position. Secure the tank with four
#14 x 2" long pan head screws and washers on all
tank mounts.
Minimum water consumption per flush1 Pt. (.47L)
Holding tank capacity . . . . . . . . . . 9.5 Gal. (36L)
Fresh water supply pressure . . . . . . . . . 5-80 PSI
Water inlet size . . . . . . . . . . . . . . . . . . . 1/2" NPT
Holding tank discharge fitting . . . . . . . 1-1/2" NPT
Vent fitting . . . . . . . . . . . . . . . . . . . . . . . 5/8" Barb
Unit weight . . . . . . . . . . . . . . . . . . 41 Lbs. (19Kg)
Dimensions:
3. Run 5/8" (16mm) I.D. hose to vent fitting and secure
with hose clamps.
Install thru-hull vent fitting:
(not supplied with unit – SeaLand part number 307236368)
4. Drill hole through the hull, well above water line
and directly above SeaLand toilet. Hole location is
determined by routing and length of hose.
2
Installation Instructions (cont’d)
5. Apply waterproof caulk around underside of thru-hull
vent fitting.
12.Route hose from tank to deck fitting and secure with
hose clamp.
Note: The holding tank on the 711-M28 is designed
to withstand discharge by a properly operating
discharge pump.
6. Install thru-hull vent fitting and secure snugly with
nut. Wipe off excess caulk with damp cloth.
7. Attach remaining end of vent hose to thru-hull
fitting with hose clamp.
Toilet Installation:
13.Push button on back of flush pedal, then pull flush
pedal cover away from pedal to expose water valve.
Remove plastic pedestal cover from toilet base.
Dockside Discharge Fitting: (not supplied by SeaLand)
8. Drill hole in deck directly above SeaLand toilet. Hole
location is determined by routing space and length
of hose.
9. Screw 1-1/2" FPT x 1-1/2" hose barb into bottom of
deck fitting.
14.Install the (4) 1/4-20 x 1-3/4" long studs in inserts on
the tank top.
10.Apply waterproof caulk around deck hole and install
deck fitting into 2-1/4" (57mm) hole with screws. Wipe
off excess caulk with a damp cloth.
15.Place floor flange seal on studs, aligning the studs
with bumps on seat. Note: “THIS SIDE UP” should
face upwards.
11.Install 1-1/2" MPT x HUB adapter into discharge
fitting on holding tank. If necessary, PVC cement
elbow and hose adapter or hose adapter only into
1-1/2" (38mm) adapter. Secure 1-1/2" (38mm) hose
to adapter with hose clamp.
16.Place toilet on studs and secure with four washers
and four nuts.
or
3
Installation Instructions (cont'd)
Operating Instructions
Water line:
To properly use the SeaLand toilet, follow these simple
instructions:
17.Locate water valve at rear of flush lever.
1. A good biodegradable tissue such as SeaLand ®
brand is recommended.
18.Attach water supply pipe or hose from water system
to inlet fitting on back of water valve.
2. To add water to the toilet before using, lift or raise
the flush pedal.
3. To flush toilet, push pedal all the way down until
sewage leaves the toilet bowl. Water flow pressures
vary at different locations and therefore, holding the
flush lever down 4-8 seconds may be required. We
recommend 2-4 GPM (8-15 Lpm) for proper rim and
bowl wash.
4. Release flush pedal by allowing it to snap back, which
permits positive sealing around the flush ball.
5. A small amount of water should remain in the bowl.
Note: Holding the flush pedal down longer than necessary results in excessive water usage.
Caution: Do not dispose of sanitary napkins or other
non-dissolving items in the toilet.
Pedestal cover:
19.Slide back side of pedestal cover around rear of
toilet base and snap in groove. Close front half of
pedestal cover and snap in groove.
Maintenance
Cleaning
The SeaLand toilet should be cleaned regularly for
maximum sanitation and operational efficiency.
Clean the toilet bowl with a mild bathroom cleaner,
such as SeaLand® Toilet Bowl Cleaner. Do not use
chlorine or alcohol-based caustic chemicals such as
drain opening types, as they will damage the seals.
If an odor is apparent from the toilet:
1. Clean out system by flushing several gallons of fresh
water through with one cup of liquid laundry soap.
2. Add odor control deodorant in amount specified for
your holding tank capacity after cleaning and every
few days during use.
Winterizing
At the end of each season, the SeaLand toilet should be
winterized for storage by either draining or using potable,
water-safe antifreeze in the system.
To drain:
Flush pedal cover:
1. Thoroughly flush system with fresh water.
20.Put flush pedal cover back in place.
2. Empty holding tank.
3. Shut off water supply to toilet. Remove inlet
waterline.
4. Press flush lever until all water is drained from
toilet.
4
Maintenance (cont’d)
Customer Service
To use antifreeze:
Dometic has a strong, worldwide network to assist in
servicing and maintaining your SeaLand toilet if parts
or service are required. Before calling, please have the
following information available. Your cooperation in having this information ready is appreciated and allows our
Customer Service Department to better meet your needs.
When you call, we will direct you to the nearest parts
distributor.
1. Thoroughly flush system with fresh water.
2. Empty holding tank.
3. Drain potable water tank.
4. Add freshwater antifreeze and water mixture
through toilet and into the waste holding tank. Each
installation is different, so amounts may vary. User
discretion is required to assure adequate protection.
1. Toilet Model Number
2. Serial Number
5. Empty holding tank.
3. Part Number, Description and Quantity (See Parts
List.)
Note: Use nontoxic antifreeze designated for potable
water systems (see boat owner’s manual).
When you have gathered all the required information,
call us at one of the following telephone numbers from
8:00 a.m. to 5:00 p.m. (Eastern Time) Monday through
Friday, or email us.
Caution: Never use automotive-type antifreeze in
freshwater systems.
Preparing For Summer Use
Telephone: 1- 800-321-9886 USA and Canada
330-439-5550 International
Fax: 330-496-3097 USA and Canada 330-439-5567 International
Email:[email protected]
To prepare the SeaLand toilet for summer use, turn on
water supply and check system for leaks. Flush toilet,
check for leaks and repair as necessary. Your SeaLand
toilet is now ready for use.
Model Identification
The model identification label is located on the base of
the toilet under the pedestal cover (see back page for
illustration).
Spare Parts
Your SeaLand 711-M28 toilet is designed for years of
dependable trouble free service. However, during the life
of the product certain parts may require replacement.
The following is a list of parts kits which may be required
for maintenance purposes.
Part NumberDescription
385310681Ball, Shaft & Cartridge Kit
385311462Seal Kit
385314349Water Valve Kit
385316906Vacuum Breaker Kit
5
Troubleshooting Guide
Problem
Possible Cause
Service Instructions
1. Water will not stay in bowl.
a. Loose clamp.
b. Improper seal around flush ball due
to dirt or debris on underside of
flush ball seal.
c. Worn or damaged seal.
d. Worn or damaged flush ball.
a. Tighten clamp ring adjusting nut.
b. Inspect flush ball and underside of
seal for foreign objects.
Clean if necessary.
c. Replace seal.
d. Replace flush ball.
2. Plastic flush ball will not
close completely.
a. Clamp ring is overtightened,
causing too much tension on seal
and flush ball.
b. Weak or defective spring cartridge.
a. Loosen clamp ring.
a. Dirt lodged in water valve seal.
a. Disassemble and clean water
valve.
b. Bend front of cam strap up about
1/16" (1.6mm).
c. Replace water valve assembly.
d. Replace spring cartridge.
3. Water does not shut off in
toilet (toilet overflows).
b. Cam strap is bent down, holding
water valve open.
c. Worn or defective water valve.
d. Worn or defective spring cartridge.
b. Check spring tension by letting up
on flush lever suddenly. If lever
does not snap back, replace spring
cartridge.
4. Water does not enter toilet
bowl properly.
a. Low water pressure.
b. Water valve clogged.
a. Check incoming water pressure.
b. Remove and clean filter screen
located on inlet of water valve.
5. Water leaking from water
valve. a. Loose connection.
a. Tighten bottom cap, inlet fitting
and outlet hose clamp.
b. Replace water valve.
c. Insure that threads are not crossthreaded and tighten.
d. Replace water valve.
e. Replace water valve.
f. Replace water valve.
6. Water leaking from rear of
toilet bowl.
b. Worn or defective water valve.
c. Water line connection not seated
properly.
d. Stripped threads.
e. Seal worn or missing.
f. Valve body cracked.
a. Loose hose connection.
b. Loose vacuum breaker.
c. Worn or defective vacuum breaker.
d. Cracked or defective toilet bowl.
6
a. Tighten hose connections.
b. Tighten vacuum breaker-to-bowl
connection.
c. Replace vacuum breaker
assembly.
d. Replace toilet bowl.
This page is intentionally left blank.
7
Limited Warranty
THE SELLER NAMED BELOW MAKES THE FOLLOWING WARRANTY WITH RESPECT TO
SEALAND GRAVITY-FLUSH TOILET MODEL 711-M28 ONLY
1. Two-Year Limited Warranty
1A.This Limited Warranty will be in effect for two years from the date of purchase.
1B.This Limited Warranty is made only to the First Purchaser (hereinafter called the “Original Purchaser”) who acquired the product for
Original Purchaser’s personal, family, or household-type use. The Original Purchaser should retain a copy of the sales receipt or invoice as
evidence of the date of purchase because proof of purchase is required to obtain warranty service.
1C.If this product is placed in commercial or business use, it will be warranted, to the Original Purchaser only, to be free of defects in material and
workmanship for a period of 90 days from the date of purchase.
1D.This warranty covers all parts of the Dometic toilet which is warranted to be free of defects in material and workmanship under normal use.
This warranty does not cover conditions unrelated to the material and workmanship of the product. Such unrelated conditions include, but
are not limited to, (a) faulty installation and any damage resulting from such; (b) the need for normal maintenance and any damage resulting from failure to provide such maintenance; (c) failure to follow Seller’s instructions for use of this product, including failure which may
result from not following winterization procedures; (d) any accident that results in damage to this product; (e) scratching or staining of any
ceramic or plastic component; and (f) acts of God, or misuse of any part of this product and any alteration by anyone other than the Seller.
1E.For Original Purchaser (ONLY) to obtain the benefits of this Warranty during the 2-year period (for personal use) or 90-day period
(for commercial use), the following shall apply:
(a) Original Purchaser shall contact the local dealer from whom the product was purchased; or contact the Seller
Customer Service Department at 1-800-321-9886 (8 a.m.-5 p.m. ET, USA) and provide the local dealer or
Seller Customer Service Department with sales receipt or invoice, product model and serial number from
product. The product model identification label is located on the toilet base under the pedestal cover (see
illustration).
(b) If product, while still under warranty, is returned to local dealer where purchased, the local dealer will repair,
replace or refund the product per this Warranty and as authorized by the Seller. Seller will provide necessary
replacement parts or product free of charge to Original Purchaser, including freight on such replacement
parts or product, and Seller will pay direct labor charges for such repair or replacement.
(c) Under no circumstances will Seller pay or be liable for any of Original Purchaser’s or dealer’s travel charges
Location of product ID label
or other expenses associated with bringing the product or recreation vehicle to the dealer for repair, for
providing dealer with access to the product or vehicle, or for downtime of the product or vehicle.
(d) Original Purchaser may be required to return defective product or parts when requested by Seller; in such event,
Seller will pay related freight costs.
2. The seller does not authorize any person or company to create OR EXTEND any warranty obligations
or liability on ITS behalf.
3. REPAIR OR REPLACEMENT OF, OR REFUND FOR, DEFECTIVE PRODUCT, AT SELLER’S OPTION, SHALL BE THE ORIGINAL
PURCHASER’S SOLE REMEDY UNDER THIS LIMITED WARRANTY.
IN NO EVENT SHALL SELLER BE LIABLE FOR PURCHASER’S INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
4. SELLER DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO THE PRODUCT, WHETHER EXPRESS OR IMPLIED,
AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
5. This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
SELLER:
Dometic Corporation - Sanitation Div.
13128 SR 226
Big Prairie, Ohio 44611 USA
330-439-5550
Dometic Group is a customer-driven, world-leading provider of leisure
products for the RV, automotive, truck and marine markets. We supply
the industry and aftermarket with a complete range of air conditioners,
refrigerators, awnings, cookers, sanitation systems, lighting, mobile
power equipment, comfort and safety solutions, windows, doors and
other equipment that make life more comfortable away from home.
DOMETIC CORPORATION
SANITATION DIVISION
13128 SR 226 | PO BOX 38
BIG PRAIRIE, OHIO 44611 USA
Dometic Group supplies a wide range of workshop equipment for service
and maintenance of built-in air conditioners. Dometic Group also provides
specially designed refrigerators for hotel rooms, offices, wine storage and
transport and storage of medical products.
www.DometicSanitation.com
[email protected]
Our products are sold in almost 100 countries and are produced mainly in
wholly-owned production facilities around the world.
600342689 02
® Registered; ™ Trademark of Dometic Corporatio
© Dometic Corporation
05/13
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement