Assa Abloy | Door Lock | User manual | Mechanical lock cases, hinges and door hardware
Add to my manuals66 Pages
advertisement
▼
Scroll to page 2
of 66
Mechanical lock cases, hinges and door hardware An ASSA ABLOY Group brand Contents General information............................ 3–4 Locks for interior doors ABLOY® 2011........................................... 5 ABLOY® 2014........................................... 5 ABLOY® 2016........................................... 5 ABLOY® 2018........................................... 6 ABLOY® 2020........................................... 6 ABLOY® 2025........................................... 6 ABLOY® 2040........................................... 7 ABLOY® 4238........................................... 7 ABLOY® 4249........................................... 7 ABLOY® 4260........................................... 8 ABLOY® LC290........................................ 8 ABLOY® LC291........................................ 8 ABLOY® 4290........................................... 9 ABLOY® 4291........................................... 9 ABLOY® 4570........................................... 9 ABLOY® 9456......................................... 10 ABLOY® 4230......................................... 10 ABLOY® 4202......................................... 10 ABLOY® 4203......................................... 11 ABLOY® 4207......................................... 11 ABLOY® 4208......................................... 11 ABLOY® 4292......................................... 12 ABLOY® 4293......................................... 12 ABLOY® 4297......................................... 12 ABLOY® 4298......................................... 13 Lock cases for wooden/steel doors ABLOY® LC102...................................... 14 ABLOY® LC190...................................... 15 ABLOY® LC193...................................... 15 ABLOY® LC194...................................... 16 ABLOY® LC195...................................... 16 ABLOY® LC197...................................... 17 ABLOY® LC960...................................... 17 ABLOY® LC100...................................... 18 ABLOY® 4190......................................... 18 ABLOY® 4190T....................................... 19 ABLOY® LC204...................................... 19 ABLOY® 4194......................................... 19 ABLOY® 4195......................................... 20 ABLOY® 4195T....................................... 20 ABLOY® 4197......................................... 20 ABLOY® 4960......................................... 21 ABLOY® E4190....................................... 21 ABLOY® E4194....................................... 22 ABLOY® E4195....................................... 22 ABLOY® LC200...................................... 23 ABLOY® LC210...................................... 23 ABLOY® 4865......................................... 24 ABLOY® 4272......................................... 24 ABLOY® 4272MP................................... 24 Exit locks for wooden/steel doors ABLOY® LE180....................................... 25 ABLOY® LE184....................................... 25 ABLOY® LE185....................................... 26 ABLOY® LE181....................................... 26 ABLOY® LE183....................................... 27 ABLOY® LE186....................................... 27 Double cylinder lock cases for wooden/steel doors ABLOY® LC120...................................... 28 ABLOY® LC121...................................... 28 ABLOY® LC121T.................................... 28 ABLOY® LC122...................................... 29 ABLOY® LC123...................................... 29 ABLOY® LC125...................................... 29 ABLOY® LC127...................................... 30 Security and additonal locks for wooden /steel doors ABLOY® SL905...................................... 30 ABLOY® SL905MP................................. 30 ABLOY® SL928S.................................... 31 ABLOY® 4181......................................... 31 ABLOY® LC211...................................... 31 ABLOY® 4232......................................... 32 ABLOY® 4232MP................................... 32 Security locks for narrow profile doors ABLOY® LC306...................................... 33 ABLOY® LC306H.................................... 33 ABLOY® LC307...................................... 33 ABLOY® LC307H.................................... 34 Lock cases for narrow profile doors ABLOY® LC300...................................... 34 ABLOY® LC301...................................... 34 ABLOY® LC301F..................................... 35 ABLOY® LC302...................................... 35 ABLOY® LC303...................................... 35 ABLOY® LC305...................................... 36 Double cylinder lock cases for narrow profile doors ABLOY® LC130...................................... 36 ABLOY® LC131...................................... 36 ABLOY® LC132...................................... 37 Exit locks for narrow profile doors ABLOY® LE310....................................... 37 ABLOY® LE314....................................... 38 ABLOY® LE315....................................... 38 Installation accessories ABLOY® 2050 installation box ............... 39 ABLOY® 2051 installation box ............... 39 Transfer device ABLOY® 518................. 39 Rounding pieces.................................... 40 Escutcheons........................................... 40 Cover plates........................................... 40 Cover front plates................................... 41 Keys....................................................... 41 Striker plates.......................................... 42 Hinges................................................... 46 Drill-in hinges for windows.................... 46 Hinges for interior doors........................ 46 Hinges for exterior doors....................... 47 Hinges for glass doors........................... 49 Concealed hinges................................... 49 Hardware............................................... 50 Letter plates........................................... 50 Quick bolt............................................... 51 Flush bolt............................................... 52 Mortises................................................ 53 Locks for interior doors......................... 53 Lock cases for wooden/steel doors........ 56 OneFit mortise........................................ 58 Double cylinder lock cases for wooden/ steel doors............................................. 60 Security and additional locks for wooden/ steel doors............................................. 60 Security locks for narrow profile doors.. 61 Lock cases for narrow profile doors...... 62 Double cylinder lock cases for narrow profile doors.......................................... 62 Installation accessories.......................... 63 Striker plates.......................................... 63 Multipoint locking applications.............. 65 General information Product information Locks with automatic deadlocking Many ABLOY® lock cases are equipped with an automatic deadlocking action, which fascilitates the use of the lock. The automatical deadlocking action is controlled by a snib in the forend. In the deadlocking mode it is not possible to retract the bolt other but using the cylinder or thumbturn and consequently a lock case with an automatic deadlocking must always be fitted with a cylinder or a thumbturn. Automatic deadlocking lock cases are designed to function perfectly with 2–5 mm door clearance. T-model The automatic deadlocking is controlled by a turning snib in the forend. The snib can be turned by a square key. The position of the turning snib: Turned clockwise = deadlocking. Turned anticlockwise = day use. ABLOY® LC100 and LC102 ABLOY® LC100 and LC102 lock case is opened by turning first the key or thumbturn and then using the handle. The snib is locked to the deadlocking mode by turning a set screw, located below the snib, about two turns anticlockwise by a hexagonal key, until the screw stops and is opened by turning the screw clockwise. Double cylinder lock cases and transfer devices Double cylinder lock cases and transfer devices can be used to combine two different key systems in the same door. For example doors for electrical control rooms, boiler rooms, garbage sheds or similar service premises are suitable for application, thus making it possible to provide an access for e.g. a service company to enter the room with their own keys. Applications When choosing a lock case for a particular purpose, you should pay attention to the demands for: burglary protection, insurance company requirements, fire resistance, emergency exit safety, operational safety, durability, mortice and fittings standards, corrosion protection. The most common applications and the lock cases used: Interior doors Interior doors/standard: 2014, 2020, 2040, Interior doors/renovation: 2020, 2025 Public buildings: 2018, 4203, 4290, 4293, LC208 Narrow profiles: LC300 Toilets/bathrooms/standard: 2014, 2025, 2040 Public buildings: 4207, 4291, 4297, 2025, LC200, LC291 Saunas: 4238 Lockable interior doors/standard: 2011, 2016, 2018, 4230, 4260, 4570, 9456 Public buildings: 4190, LC190, 4202, 4230, 4292, LC200 Narrow profiles: LC302, LC305 Sliding doors/standard: 4249 Public buildings: 4960, LC960 Exterior doors Houses/standard: LC100, LC102, LC190, 4190, 4272, LC200, LC209, LC209A, LC210 Public buildings: 4190 (T), 4195 (T), 4272, LC190, LC195, LC200, LC209, LC209A, LC210 Narrow profiles: LC302, LC305 Steel doors: 4272MP Additional locking Wooden doors: SL905, SL928, 4181, 4232, 4298, 4208, LC211 Narrow profiles doors: LC306, LC307 Sliding narrow profiles doors: LC306H, LC307H Steel doors: SL428MP, 4232MP, SL905MP Fire doors Interior doors/standard: LC209, LC209A, LC210, 2011, 2014, 2025 Interior doors/public building: 4290, 4291, 2025 Houses/public building: 4190, 4190T, 4194, 4197, LC100, LC102, LC190, LC194, LC197 LC200, LC202, LC203, LC204, LC206, LC208, LC209, LC209A, LC210, 4272 Narrow profiles: LC300, LC301F, LC303, LC305 Steel doors: 4272MP Emergency exits Wooden doors: One leaf: LC193, LC203, LE180, LE184, LE185 Double door active leaf: LE181, LE183, LE185 Narrow profiles: One leaf: LC301, LC301F, LE310, LE314, LE315 Double door active leaf: LE310, LE314, LE315 Microswitch locks In microswitch locks the switch changes the status when the bolt has reached its fully protruded position and/or it’s deadlocked. The ABLOY® microswitch lock case is equipped with a microswitch, which has a change-over contact. The switch follows mechanically the moves of the bolt or the deadlocking elements and changes its status according to the position of the actuating elements. The switching function of a particular lock type is clarified in the descriptions of the lock types. - The microswitch version of each lock case has a product code ending with “X”. The product code for the microswitch version of e.g. 4190 is 4190X. - Drilling, installation and mounting of door furniture is carried out in the same way as of corresponding mechanical lock cases, except that the cable of the microswitch needs to be routed to the door frame. - Protective voltage must be used with microswitch lock cases. Maximum current 1 A Maximum voltage 60 VDC, 42 VAC Maximum power 24 W - A lock with a microswitch can be used as a sensor or switch for e.g. passage control or burglar Position alarm systems. information of - Security locks can be used as switching latchbolt and by-pass locks for burglar alarm systems. 3 General information Handing Cylinders Please specify the handing when ordering a lock case. A simple way to determine if the door (and lock) is left or right handed is to look at the door from the hinge side. The cylinder to be used with a lock case is specified for each product. We have used the following abbreviations: CYLINDER AND FITTINGS KEY TYPES ABLOY® C, N, T, U Finnish range ABLOY® CLASSIC (C), rotation direction only to clockwice ABLOY® PROTEC (N), ABLOY® PROTEC2 (T), ABLOY® NOVEL (U) SCAND Scandinavian range oval/round ABLOY® PROTEC2 (T), ABLOY® PROTEC (N), ABLOY® NOVEL (U), ASSA, TrioVing o.e. Euro DIN Europrofile DIN range ABLOY® PROTEC (N), ABLOY® PROTEC2 (T), ABLOY® NOVEL (U), FAB o.e. Left hand (1 & 3) The hinges are on the left side. Right hand (2 & 4) The hinges are on the right side. Dimensions & mortises The drawings in this catalogue are available at www.abloy.com Please contact the importer or your local dealer for more detailed information. General finishes Fe/Cr Chrome plated steel Fe/Zn Zinc plated steel Fe/ZL Zinc chromated and lacquered steel Fe/Mme (Fe/JME) Powder coated steel, brass colour Fe/Har /Fe/JHA) Powder coated steel, grey colour Fe/Val (Fe/JVA) Powder coated steel, white colour Fe/HCr Satin chrome plated steel ZNALCU/Mme Powder coated zamac, brass colour (ZNALCU/JME) Fe/ZnCLA Yellow chromated and lacquered steel (Fe/YECRLQ) Ms/Cr Chrome plated brass Ms/HCr Satin chrome plated brass Ms/HaLa Brushed and lacquered brass Ms/Ki Polished brass Ms/KiLa Polished and lacquered brass RST (Rt) Stainless steel Special finishes: E.g. special powder colours, chemical nickel, brass plated are made only to order. Propriety to applications must be checked. In wet places or other corrosive atmospheres, as indoor swimming baths, spas, food and chemical industry etc, a chemical nickel coating is recommended. 4 Due to continuous product development we reserve the rights to technical modifications. Locks for interior doors ABLOY® 2011 Lever lock for interior doors.The lock features 5 levers to give 250 different key combinations. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. The lock is fitted with lever handles and an escutcheon. The lock can also be eguipped with DIN standard fittings. See page 41. Striker plate 0043, 0045, 0053, 0055, 0068,0068B Finish Fe/Zn, Fe/Mme Fire resistance Yes Mortise standard SFS 5210 SS 81 73 82 Please see page 53 ABLOY® 2014 Lock for interior doors. It can be locked with either a key or a toilet thumbturn. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. The lock can be used with a lever handle only or with both a lever handle and a key or a toilet thumbturn. The lock can also be eguipped with DIN standard fittings. See page 41. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Finish Fe/Zn, Fe/Mme Fire resistance Yes Mortise standard SFS 5210 SS 81 73 82 Please see page 53 ABLOY® 2016 Cylinder lock case for interior doors. It can be locked using a key or a thumbturn. In locked position, the deadbolt protrudes 14 mm. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Finish Fe/ZL Fire resistance Yes Cylinder SCAND Mortise standard SFS 5210 SS 81 73 82 Please see page 53 5 Locks for interior doors ABLOY® 2018 Cylinder lock for interior doors. The lock can be opened and locked by turning the key one turn. In locked position, the deadbolt protrudes 14 mm. The latch can be retracted both by handles or by key. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Finish Fe/Mme, Fe/ZL Fire resistance Yes Cylinder Euro DIN Mortise Special mortise standard, please see page 53 ABLOY® 2020 Lock for interior doors. It has one latch bolt which can be deadlocked with either a key or a toilet thumbturn. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. The lock can be used with a lever handle only or with both a lever handle and a key or a toilet thumbturn. The lock fits into the same mortise as e.g. ASSA 404 and 404T. 2020 replaces the following old lock types: BODA 408-409-418-420-422-423-448-501-502-503 and ASSA 404 and 404T Striker plate Finish Fire resistance Mortise standard ABLOY® 2025 6 0043, 0045, 0053, 0055, 0068, 0068B Fe/Mme Yes SFS 5210 SS 81 73 82 Please see page 53 A toilet door lock, which is locked by turning the lever handle upwards. The finish can easily be changed by using decorative cover front plate. The lock can be used without decorative cover front plate also. Lock handing can easily be changed by pulling out the latchbolt and turning it 180° clockwise. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Standard finish, lock Fe/Mme Decorative front plate 7640 Fe/Cr, Fe/HCr, Ms/HaLa, Ms/Ki, Rst Fire resistance Yes Mortise standard SFS 5210 SS 81 73 82 Please see page 53 The mortise for the forend should be 3 mm deep when using cover front plate 7640. Locks for interior doors ABLOY® 2040 Lock for interior doors. The lock can be used with a lever handle only or with both a lever handle and a toilet thumbturn. Lock handing can easily be changed by pulling out the latch bolt and turning it 180° clockwise. The lock can also be eguipped with DIN standard fittings. See page 41. Striker plate Standard finish Additional finish Fire resistance Mortise standard 0043, 0045, 0053, 0055, 0068, 0068B Fe/Mme, Fe/Zn Fe/Cr, Fe/HCr, Ms/HaLa, Ms/Ki, Rst – SFS 5210 SS 81 73 82 Please see page 53 ABLOY® 4238 Symmetric roller latch. The roller latch protrusion can be adjusted by means of a screw in the front plate. The door must have a door pull. For reasons of safety, a special striker plate is used in conjunction with the roller latch. Striker plate 0046, 0078 Finish ZNALCU/Mme Fire resistance – Mortise standard SFS 5210 SS 81 73 82 Please see page 53 ABLOY® 4249 Lock case for lightweight sliding and folding doors. The hookbolt can be locked. Either by using a key or toilet thumbturn. Striker plate 4662 Finish Fe/Mme Additional finish Fe/Cr, Fe/HCr, Ms/HaLa, Ms/KiLa, Rst Fire resistance – Mortise standard SFS 5210 SS 81 73 82 Please see page 53 7 Locks for interior doors ABLOY® 4260 Cylinder mortise lock with an automatically deadlocking latchbolt for interior doors. Deadlocking is controlled by a snib in the front plate. Snib position: UP = Deadlocking, latchbolt protrudes 20 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. Lock can also be opened with lever handles. Striker plate Finish Cylinder Fire resistance Mortise standard 0043, 0045, 0053, 0055, 0068, 0068B Fe/Mme, Fe/Zn ABLOY® C, N, T, U – SFS 5210 SS 81 73 82 Please see page 53 ABLOY® LC290 Mortise lock with a lever handle function only. Recommended for public buildings. Striker plate: 4690, 4691, LP711, LP714, LP721, LP731 Finish: Fe/ZL Fire resistance: Wooden doors EI115 – EI130 and EI215 – EI2 30, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise: OneFit mortise Please see page 57 ABLOY® LC291 Mortise lock for toilet doors in public buildings. The lock is suitable for use with lever handles and a toilet thumbturn. 8 Striker plate: 4690, 4691, LP711, LP714, LP721, LP731 Finish: Fe/ZL Fire resistance: Wooden doors EI115 – EI130 and EI215 – EI2 30, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise: OneFit mortise Please see page 57 Locks for interior doors ABLOY® 4290 Mortise lock with a lever handle function. Recommended for public buildings. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209 Please see page 58 ABLOY® 4291 Mortise lock for toilet doors in public buildings. The lock is suitable for use with lever handles and a toilet thumbturn. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard Please see page 55 ABLOY® 4570 Cylinder mortise lock with an automatically deadlocking latchbolt for interior doors. Deadlocking is controlled by a snib in the front plate. Snib position: UP = Deadlocking, latchbolt protrudes 20 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. The lock can also be opened with lever handles. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Other striker plates see page 37–38 Finish Fe/ZL Cylinder ABLOY® N, T, U, SCAND Fire resistance – Mortise standard SFS 5210 SS 81 73 82 Please see page 53 9 Locks for interior doors ABLOY® 9456 Cylinder lock case for interior doors. A turn of the key or thumbturn clockwise throws the latchbolt 20 mm and deadlocks. The lock is opened by turning the key or thumbturn anticlockwise thereby allowing the latchbolt to protrude 14 mm for day mode. The door can then be opened using the lever handles. Striker plate 0043, 0045, 0053, 0055, 0068, 0068B Other striker plates see page 37–38 Finish Fe/ZL Cylinder ABLOY® N, T, U, SCAND Fire resistance – Mortise standard SFS 5210 SS 81 73 82 Please see page 53 ABLOY® 4230 Symmetric exterior door lock for DIN eurocylinder. The handing of the lock can easily be changed by turning the latch 180º. The latch is controlled by lever handles or a cylinder and the deadbolt the cylinder. The deadbolt is protruding 20 mm. Compatible with similar GOST norm products. Striker plate 0029, 4667, 4669 Finish Cylinder Fe/Mme, Fe/ZL Euro DIN Fire resistance – Mortise standard Please see page 56 ABLOY® 4202 Symmetrical DIN euro cylinder lock for fire doors. The latch is controlled by lever handles or a cylinder and the deadbolt by the cylinder. The deadbolt is protruding 20 mm. The lock can be used with DIN escutcheons and long plates. The handedness can easily be changed by pushing the latch bolt inside the lock case and turning it. 10 Striker plate 4673 Finish Rst, Ms/KiLa Cylinder Euro DIN Fire resistance Yes Locks for interior doors ABLOY® 4203 Symmetrical DIN lock for fire doors with handle function. The lock can be used with DIN escutcheons and long plates. The handedness can easily be changed by pushing the latch bolt inside the lock case and turning it. Striker plate 4673 Finish Rst, Ms/KiLa Fire resistance Yes ABLOY® 4207 Symmetric DIN lock for toilet doors. The handing of the lock can easily be changed by turning the latch 180º. The latch is controlled by lever handles and the deadbolt by a toilet thumbturn (8 mm spindle). The deadbolt is protruding 10 mm. Striker plate 4673 Finish Rst, Ms/KiLa Fire resistance – Mortise standard Please see page 56 ABLOY® 4208 Symmetrical DIN lock with deadbolt function. The deadbolt is controlled by the cylinder. The deadbolt is protruding 20 mm. The lock can be used with DIN escutcheons and long plates. Striker plate 4673 Finish Rst, Ms/KiLa Cylinder Euro DIN Fire resistance – 11 Locks for interior doors ABLOY® 4292 Symmetrical DIN euro cylinder lock for fire doors. The latch is controlled by lever handles or a cylinder and the deadbolt by the cylinder. The deadbolt is protruding 20 mm. The lock can be used with DIN escutcheons and long plates. The handedness can easily be changed by pushing the latch bolt inside the lock case and turning it. Striker plate 0029, 4667, 4669 (Finish Fe/Mme, Fe/ZL) Striker plate 4673 (Finish Rst, Ms/KiLa) Finish for lock case Fe/Mme, Fe/ZL, Rst, Ms/KiLa Cylinder Euro DIN Fire resistance Yes ABLOY® 4293 Symmetrical DIN lock for fire doors with handle function. The lock can be used with DIN escutcheons and long plates. The handedness can easily be changed by pushing the latch bolt inside the lock case and turning it. Striker plate 0029, 4667, 4669 (Finish Fe/Mme, Fe/ZL) Striker plate 4673 (Finish Rst, Ms/KiLa) Finish for lock case Fe/Mme, Fe/ZL, Rst, Ms/KiLa Fire resistance Yes ABLOY® 4297 Symmetric DIN lock for toilet doors. The handing of the lock can easily be changed by turning the latch 180º. The latch is controlled by lever handles and the deadbolt by a toilet thumbturn (8 mm spindle). The deadbolt is protruding 10 mm. 80 43 55 20 15 55 3 ,5 10 Finish for lock case Fe/Mme, Fe/ZL, Rst, Ms/KiLa 72 8 235 Striker plate 4673 (Finish Rst, Ms/KiLa) 155 Striker plate 0029, 4667, 4669 (Finish Fe/Mme, Fe/ZL) ,5 10 Fire resistance – 8 Mortise standard Please see page 57 12 38 4297 901072 Locks for interior doors ABLOY® 4298 Symmetrical DIN lock with deadbolt function. The deadbolt is controlled by the cylinder. The deadbolt is protruding 20 mm. The lock can be used with DIN escutcheons and long plates. Striker plate 0029, 4667, 4669 (Finish Fe/Mme, Fe/ZL) Striker plate 4673 (Finish Rst, Ms/KiLa) Finish for lock case Fe/Mme, Fe/ZL, Rst, Ms/KiLa Cylinder Euro DIN Fire resistance – 13 Lock cases for wooden / steel doors ABLOY® LC102 Cylinder lock case with an automatically deadlocking latchbolt. The lock must always be equipped with handles on both inside and outside. The deadlocking is controlled by a snib in the forend. When the snib is in deadlocking mode, the door is opened by turning the outside key 180° or the inside thumbturn 90°. The handles are then activated, and the latchbolt can be retracted. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lever handles are activated by the key or the thumbturn. DOWN = Latchbolt protrudes 14 mm. The door is opened with the lever handles. The lock case LC102 is fitted with a feature to prevent unauthorized use of the snib. The snib is locked to the deadlocking mode by turning a set screw, located below the snib, about two turns anticlockwise by a hexagonal key, until the screw stops and is opened by turning the screw clockwise. LC102X is the microswitch version of the lock. The switch changes it’s status when the bolt has protruded to 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate: Finish: Cylinder: Fire resistance: 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U Wooden doors EI115 - EI1 30 and EI215 – EI2 30, Metal doors EI115 - EI1120 and EI215 – EI2120 Mortise standard: OneFit mortise. Please see page 58 14 Lock cases for wooden / steel doors ABLOY® LC190 A cylinder lock case with an automatically deadlocking latchbolt. The latchbolt is deadlocked when both triggering bolt and latchbolt are retained inside the lock case. The deadlocking is controlled by a snib in the forend. The lock case is fitted with at feature to prevent unauthorized use of the snib. The snib can be moved by turning first the key or thumbturn. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. The lock can also be opened with the lever handles. LC190X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate: 4690, 4691, LP711, LP714, LP721, LP731 Finish: Fe/ZL Cylinder: ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI1120 and EI215 – EI2120 Mortise standard: OneFit mortise Please see page 58 ABLOY® LC193 Cylinder lock case for emergency exits. The latchbolt deadlocks automatically when the door is closed, protruding 21 mm. The lock case is suitable for use with a double cylinder and an emergency exit thumbturn. The bolt is opened with either the key or the emergency thumbturn. LC193X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate: 4690, 4691, LP711, LP714, LP721, LP731 Finish: Fe/ZL Cylinder: ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI11120 and EI215 – EI2120 Mortise standard: OneFit mortise Please see page 58 15 Lock cases for wooden / steel doors ABLOY® LC194 Lock case with an automatically deadlocking latchbolt. The latchbolt is deadlocked when both triggering bolt and latchbolt are retained inside the lock case. The latchbolt protrudes to 21 mm when the door is closed. The lock has no lever handle operation. The bolt is opened with either a key or a thumbturn. LC194X is the microswitch version of the lock. The switch changes it’s status when the bolt protrudes 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate: 4690, 4691, LP711, LP714, Finish: Fe/ZL Cylinder: ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI11120 and EI215 – EI2120 Mortise standard: OneFit mortise Please see page 58 ABLOY® LC195 Lock case with an automatically deadlocking latchbolt. The latchbolt is deadlocked when both triggering bolt and latchbolt are retained inside the lock case. Deadlocking is controlled by a snib in the front plate. The lock cases fitted with at feature to prevent unauthorized use of te snib. The snib can be moved by turning first the key or thumbturn. The lock has no lever handle operation. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt is retained inside the lock case. LC195X is the microswitch version of the lock. The switch changes it’s status when the bolt protrudes 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate: Finish: Cylinder: Fire resistance Mortise standard: 16 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U – OneFit mortise Please see page 58 Lock cases for wooden / steel doors ABLOY® LC197 Cylinder lock case with a cylinder function for fire doors. The lock is opened by a key or a thumbturn. The non-deadlocking latchbolt protrudes 14 mm. The lock can also be used with electromechanical striker plates. Striker plate: 4690, 4691, LP711, LP714, LP721, LP731 Finish: Fe/ZL Cylinder: ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI11120 and EI215 – EI2120 Mortise standard: OneFit mortise Please see page 58 ABLOY® LC960 Cylinder lock case with an automatically deadlocking hookbolt for folding and sliding doors. The deadlocking is controlled by a snib in the forend. Snib position: UP = Deadlocking, when the door is closed. The lock can be opened with a key or a thumbturn. DOWN = Hookbolt is retained inside the lock case. Striker plate: 4662 Finish: Fe/ZL Cylinder: ABLOY® C, N, T, U Fire resistance – Mortise standard: OneFit mortise Please see page 58 17 Lock cases for wooden / steel doors ABLOY® LC100 Lock case with an automatically deadlocking latchbolt. The lock must always be equipped with handles, as the latchbolt is retracted with the handles only. The deadlocking is controlled by a snib in the forend. When the snib is in deadlocking mode, the door is opened by turning the outside key 180° or the inside thumbturn 90°. The handles are then activated, and the latchbolt can be retracted. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lever handles are activated by the key or the thumbturn. DOWN = Latchbolt protrudes 14 mm. The door is opened with the lever handles. The lock case LC100 is fitted with a feature to prevent unauthorized use of the snib. The snib is locked to the deadlocking mode by turning a set screw, located below the snib, about two turns anticlockwise by a hexagonal key, until the screw stops and is opened by turning the screw clockwise. LC100X is the microswitch version of the lock. The switch changes it’s status when the bolt has protruded to 21 mm. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder Fire resistance: ABLOY® C, N, T, U Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209 Please see page 58 ABLOY® 4190 18 Lock case with an automatically deadlocking latchbolt. The deadlocking is controlled by a snib in the forend. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. The lock can also be opened with the lever handles. 4190X is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209. Please see page 58 ABLOY® LC204 Lock cases for wooden / steel doors ABLOY® 4190T Lock case with an automatically deadlocking latchbolt. The deadlocking function is controlled with a rotating snib, operated by a square key, in the forend. Snib function: TURN CLOCKWISE = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. TURN ANTICLOCKWISE = Latchbolt protrudes 14 mm. The lock can also be opened with the lever handles. 4190TX is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209. Please see page 58 Lock case with an automatically deadlocking latchbolt. The deadlocking is controlled by a snib in the forend. Snib position: UP = Deadlocking, latchbolt protrudes 20 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. The lock can also be opened with the lever handles. LC204X is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance Yes Mortise standard SFS 5208, SS 81 73 83 Please see page 58 ABLOY® 4194 Lock case with an automatically deadlocking latchbolt. The latchbolt protrudes to 21 mm when the door is closed. The lock has no lever handle operation. The bolt is opened with either a key or a thumbturn. 4194X is the microswitch version of the lock. The switch changes it’s status when the bolt has protruded to 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209. Please see page 58 19 Lock cases for wooden / steel doors ABLOY® 4195 ABLOY® 4195T Lock case with an automatically deadlocking latchbolt. The latchbolt can be retained inside the lock case. Deadlocking is controlled by a snib in the front plate. The lock has no lever handle operation. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt is retained inside the lock case. The door is kept closed by using a door closer. 4195X is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard SFS 5209 Please see page 58 Lock case with an automatically deadlocking latchbolt. The latchbolt can be retained inside the lock case and deadlocking is controlled with a rotating snib, operated by a square key, in the forend. The lock has no lever handle function. Snib function: TURN CLOCKWISE = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. TURN ANTICLOCKWISE = Latchbolt is retained inside the lock case. The door is kept closed by using a door closer. 4195TX is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard SFS 5209. Please see page 58 ABLOY® 4197 Lock case with a cylinder function for fire doors. The lock is opened by a key or a thumbturn. The non-deadlocking latchbolt protrudes 14 mm. The lock can also be used with electromechanical striker plates. Following striker plates are recommended to be used with a microswitch locking box: 4692, 4693 Striker plate 20 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209. Please see page 58 Lock cases for wooden / steel doors ABLOY® 4960 Lock case with an automatically deadlocking hookbolt for folding and sliding doors. The deadlocking is controlled by a snib in the forend. Snib position: UP = Deadlocking, when the door is closed. The lock can be opened with a key or a thumbturn. DOWN = Hookbolt is retained inside the lock case. Striker plate 4662 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard SFS 5209 Please see page 58 ABLOY® E4190 Exit lock cases with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a lever handle. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocking, latchbolt protrudes 17 mm The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt protrudes 14 mm. The lock can be opened from outside by lever handle also. Striker plate LP711, LP714, LP721, LP731, 4690, 4691 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209 21 Lock cases for wooden / steel doors ABLOY® E4194 Exit lock case with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The lock is deadlocked always when the door is closed. Latchbolt protrudes 17 mm. Striker plate LP711, LP714, LP721, LP731, 4690, 4691 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 – EI160 and EI215 – EI260, Metal doors EI115 – EI1120 and EI215 – EI2120 Mortise standard SFS 5209 ABLOY® E4195 Exit lock case with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocking, latchbolt protrudes 17 mm The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt is retained inside the lock case. 22 Striker plate LP711, LP714, LP721, LP731, 4690, 4691 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard SFS 5209 Lock cases for wooden / steel doors ABLOY® LC200 Lock case with a deadbolt protruding 20 mm and a latchbolt. The deadbolt is locked and retracted by turning the key or thumbturn 90°. A further 5° turn will retract the latchbolt as well. The latchbolt is retracted also by the lever handles. LC200X is the microswitch version of the lock. The switch changes it’s status when the bolt has protruded to 20 mm. Striker plate LP712, LP717, LP722, LP732, 0034, 0079 Finish Fe/ZL Cylinder ABLOY® N, T, U, SCAND Fire resistance Yes Mortise standard SFS 5208 SS 81 73 83 Please see page 58 ABLOY® LC210 Security mortise lock (security grade 5 according to EN 12209) with a hardened bolt and drilling protection. The deadbolt has 20 mm bolt throw. The deadbolt is locked and retracted by turning the key 360° or thumbturn 90°. The key can only be removed when the deadbolt is fully locked or retracted. The latchbolt is retracted by the lever handles only. LC210X is the microswitch version of the lock. The switch changes it’s status when deadbolt protrudes moves to 20 mm. Striker plate LP710, LP712, LP717, LP722, LP732, 0079 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance Yes Mortise standard SFS 5208 SS 81 73 83 Please see page 58 23 Lock cases for wooden / steel doors ABLOY® 4865 Security mortise lock (security grade 5 according to EN 12209) with a hardened bolt. The deadbolt has a 20 mm bolt throw. The deadbolt is locked and retracted by turning the key 360° or thumbturn 90°. The key can only be removed when the deadbolt is fully locked or retracted. The latchbolt is retracted by the lever handles only. 4865X is the microswitch version of the lock. The switch changes it’s status when deadbolt moves to 20 mm. The product without drilling protection is P865. Striker plate LP710, LP712, LP717, LP722, LP732, 0079 Finish Fe/ZL Cylinder SCAND Fire resistance Yes Mortise standard SFS 5208 SS 81 73 83 Please see page 58 ABLOY® 4272 Security lock (security grade 3 according to EN 12209). The hardened hookbolt with intermediate locking positions is locked and retracted by turning the key 360°. The deadbolt protrudes 23 mm. Lock handing can easily be changed by pushing in the latchbolt and turning it 180°. The lock can be used with DIN standard fittings. The lock is applicable also for fire doors. Drilling protection 404252-B, is available as an optional accessory. 4272X is the microswitch version of the lock. The switch changes the status during the last key throw to the locking direction. Striker plate Finish Cylinder Fire resistance Mortise standard ABLOY® 4272MP 24 LP760 R/L Fe/ZL Euro DIN Yes Please see page 59 Security lock (security grade 3 according to EN 12209) combined with multipoint module. The hookbolt with intermediate locking position is locked and retracted by turning the key 360°. The deadbolt protrudes 23 mm. Lock handing can easily be changed by pushing in the latchbolt and turning it 180°. Multipoint module provides several multipoint locking applications, see page 67. The lock can be used with DIN standard fittings. The lock is applicable also for fire doors. Drilling protection 404252-B, is available as an optional accessory. 4272MPX is the microswitch version of the lock. The switch changes the status during the last key throw to the locking direction. Striker plate LP760 R/L Finish Fe/ZL Cylinder Euro DIN Fire resistance Yes Mortise standard Please see page 59 Exit locks for wooden/steel doors ABLOY® LE180 Exit lock cases with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a lever handle. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocking, latchbolt protrudes 17 mm The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt protrudes 14 mm. The lock can be opened from outside by lever handle also. LE180X is the microswitch version of the lock. The switch changes the status when latchbolt is protruded from 14 mm to 17 mm. Following striker plates are recommended to be used with microswitch version: 4692, 4693. Striker plate LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI1120 and EI215 – EI2120 Mortise standard OneFit mortise ABLOY® LE184 Exit lock case with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The lock is deadlocked always when the door is closed. Latchbolt protrudes 17 mm. LE184X is the microswitch version of the lock. The switch changes the status when latchbolt is protruded from 14 mm to 17 mm. Following striker plates are recommended to be used with microswitch version: 4692, 4693. Striker plate LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI1120 and EI215 – EI2120 Mortise standard OneFit mortise 25 Exit locks for wooden/steel doors ABLOY® LE185 Exit lock case with automatic deadlocking latchbolt for wooden doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocking, latchbolt protrudes 17 mm The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt is retained inside the lock case. LE185X is the microswitch version of the lock. The switch changes the status when latchbolt is protruded from 14 mm to 17 mm. Following striker plates are recommended to be used with microswitch version: 4692, 4693. Striker plate LP711, LP714, LP721, LP731 FinishFe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard OneFit mortise ABLOY® LE181 22 69 14 Snib position: UP = Deadlocking The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Day latching, the lock can be opened from outside by lever handle also LE181X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. Passive lock case Finish Cylinder Fire resistance: 26 152 80 20 19 225 Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. 81 51 22 Exit lock case with automatic deadlocking latchbolt for the active side of wooden doors with two blades. The door is opened from outside with a lever handle. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The latchbolt protrudes 14 mm. EXH911, EXB911, EXH915 Fe/ZL ABLOY® C, N, T, U Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI1120 and EI215 – EI2120 Mortise standard OneFit mortise 8 4 Luettelop iirustus LE181,LE186 5,5 000596 0 81 51 22 20 19 69 80 Exit lock case with automatic deadlocking latchbolt for the active side of wooden doors with two blades. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The lock is deadlocked always when the door is closed. The latchbolt protrudes 14 mm. 225 152 22 14 LE183X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. Passive lock case EXH911, EXB911, EXH915 8 4 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance: Wooden doors EI115 - EI130 and EI215 – EI230, Metal doors EI115 - EI1120 and EI215 – EI2120 Luettelop iirustus LE183 5,5 000600 0 Mortise standard OneFit mortise ABLOY® LE186 81 51 22 20 19 Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocking The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt is retained inside the lock case. 69 225 22 14 152 80 Exit lock case with automatic deadlocking latchbolt for the active side of wooden doors with two blades. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The latchbolt protrudes 14 mm. 8 4 Luettelop iirustus LE181,LE186 5,5 Luettelop iirustus LE181,LE186 000596 Exit locks for wooden/steel doors ABLOY® LE183 0 LE186X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. 000596 Passive lock case EXH911, EXB911, EXH915 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard OneFit mortise 27 0 Double cylinder lock cases for wooden / steel doors ABLOY® LC120 Double cylinder lock case with an automatically deadlocking latchbolt. The latchbolt protrudes 21 mm. The lock is opened with a key or a thumbturn. The lock can be used in doors, which should be deadlocked always when they are closed. LC120X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 15 mm or more. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate Finish Cylinder Fire resistance Mortise standard 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U Yes Please see page 60 ABLOY® LC121 Double cylinder lock case with an automatically deadlocking latchbolt. The deadlocking is controlled by a snib in the front plate. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or a thumbturn. DOWN = Latchbolt protrudes 14 mm. The lock can be opened also with lever handles. LC121X is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate Finish Cylinder Fire resistance Mortise standard 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U Yes Please see page 60 ABLOY® LC121T Double cylinder lock case with an automatically deadlocking latchbolt. The deadlocking function is controlled with a rotating snib, operated by a square key, in the forend. Snib function: TURN CLOCKWISE = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened only with a key or thumbturn. TURN ANTICLOCKWISE = Latchbolt protrudes 14 mm. The lock can be opened with a lever handle also. LC121TX is the microswitch version of the lock. The switch changes it’s status when the latchbolt leaves its day locking position, i.e. the bolt protrudes 15 mm or more. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate 28 4690, 4691, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance Yes Mortise standard Please see page 60 Double cylinder lock cases for wooden / steel doors ABLOY® LC122 Double cylinder lock case with an automatically deadlocking hookbolt for folding and sliding doors. The deadlocking is controlled by the snib in the forend. Snib position: UP = Deadlocking, when the door is closed. The lock can be opened with a key or thumbturn. DOWN = Hookbolt is retained in the lock case. Striker plate 4662 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard Please see page 60 ABLOY® LC123 Double cylinder lock case with an automatically deadlocking latchbolt for emergency exit doors. Latchbolt protrudes 21 mm. The lock case has a double cylinder and an exit thumbturn. The lock can be opened with a key or an exit thumbturn. LC123X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 15 mm or more. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate 4690, 4691, LP711, LP714, LP721, PL731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance Yes Mortise standard Please see page 60 ABLOY® LC125 Double cylinder lock case with an automatically deadlocking latchbolt. The latchbolt can be retained inside the lock case. The lock has no lever handle function. The deadlocking is controlled by a snib in the forend. Snib position: UP = Deadlocking, latchbolt protrudes 21 mm. The lock can be opened with a key or thumbturn. DOWN = Latchbolt is retained inside the lock case. LC125X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 15 mm or more. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate Finish Cylinder Fire resistance Mortise standard 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U – Please see page 60 29 Double cylinder lock cases for wooden / steel doors ABLOY® LC127 Double cylinder lock case for fire doors. The lock has a cylinder function only and is opened with a key or thumbturn. The latchbolt protrudes 14 mm. The lock can be used with electromechanical striker plate also. Striker plates to be used with a microswitch locking box: 4692, 4693. Striker plate Finish Cylinder Fire resistance Mortise standard Security and additional locks for wooden/steel doors ABLOY® SL905 4690, 4691, LP711, LP714, LP721, LP731 Fe/ZL ABLOY® C, N, T, U Yes Please see page 60 Security lock (security grade 7 according to EN 12209) with more than 1 000 000 key combinations. The lock is equipped with a hardened hook bolt, which is locked by turning the key 360°. The patented key can only be removed when the deadbolt is fully locked or retracted. The hookbolt protrudes 20 mm. The lock can be easily installed into the same mortise as ABLOY® 428 security lock. SL905X is the microswitch version of the lock. The switch changes the status during the last ¼ turn of the key to the locking direction. Striker plate LP780, LP81 Finish Fe/ZL Fire resistance – Mortise standard Please see page 60 ABLOY® SL905MP Security lock (security grade 7 according to EN 12209) with more than 1 000 000 key combinations with multipoint module. The lock is equipped with a hardened hook bolt, which is locked by turning the key 360°. The patented key can only be removed when the deadbolt is fully locked or retracted. The hookbolt protrudes 20 mm. Multipoint module provides several multipoint locking applications, please see page 67. SL905MPX is the microswitch version of the lock. The switch changes the status during the last ¼ turn of the key to the locking direction. 30 Striker plate Finish Fire resistance Mortise standard LP780, LP81 Fe/ZL – Please see page 60 Security and additional locks for wooden/steel doors ABLOY® SL928S Security lock (security grade 7 according to EN 12209) with 100 000 key combinations. The lock is locked by turning the key 360 degrees. The key can only be removed when the deadbolt is fully locked or retracted. The hookbolt protrudes 20 mm. The lock can be easily installed into the same mortise as ABLOY® 428 security lock. SL928X is the microswitch version of the lock. The switch changes the status during the last ¼ turn of the key to the locking direction. Striker plate 0036, 0065 Finish Fe/ZL Fire resistance – Mortise standard Please see page 60 ABLOY® 4181 Security lock case (comparable with security grade 5 according to EN 12209) with hardened bolt and drilling protection. The key can only be removed when the deadbolt is fully locked or retracted. 4181X is the microswitch version of the lock. The switch changes it’s status when deadbolt moves to 20 mm. Striker plate 4690, 4691, LP710, LP711, LP714, LP721, LP731 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard SFS 5208 SS 81 73 83 Please see page 58 ABLOY® LC211 Security mortise lock case (comparable with security grade 5 according to EN 12209) with hardened deadbolt and drilling protection. The deadbolt has a 20 mm bolt throw. The deadbolt is locked and retracted by turning the key or thumbturn 360°. The key can only be removed when the deadbolt is fully locked or retracted. LC211X is the microswitch version of the lock. The switch changes it’s status when deadbolt moves to 20 mm. Striker plate 4690, 4691, LP710, LP712, LP717, LP722, LP732 Finish Fe/ZL Cylinder ABLOY® N, T, U Fire resistance – Mortise standard SFS 5208 SS 81 73 83 Please see page 58 31 Security and additional locks for wooden/steel doors ABLOY® 4232 Security lock (comparable with security grade 3 according to EN 12209). The hardened hookbolt with intermediate locking position is locked and retracted by turning the key 360°. The deadbolt protrudes 23 mm. The lock can be used with DIN standard fittings. Drilling protection 404252-B, is available as an optional accessory. 4232X is the microswitch version of the lock. The switch changes the status during the last key throw to the locking direction. Striker plate 0036, 0065, LP763 Finish Fe/ZL Cylinder Euro DIN Fire resistance – Mortise standard Please see page 61 ABLOY® 4232MP 32 Security lock (comparable with security grade 3 according to EN 12209) combined with multipoint module. The hardened hookbolt with intermediate locking position is locked and retracted by turning the key 360°. The deadbolt protrudes 23 mm. Multipoint module provides several multipoint locking applications, please see page 67. The lock can be used with DIN standard fittings. Drilling protection 404252-B, is available as an optional accessory. 4232MPX is the microswitch version of the lock. The switch changes the status during the last key throw to the locking direction. Striker plate 0036, 0065, LP763 Finish Fe/ZL Cylinder Euro DIN Fire resistance – Mortise standard Please see page 61 Striker plate 4655, LP707 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard Please see page 61 29, 2 5, 5 47. 5 5, 3 30. 25 114 25 19 1 5,1 15. 17, 163 225 Security lock case (comparable with security grade 5 according to EN 12209) for narrow profile doors. Operates with key from either side with a double cylinder or from outside with a cylinder and inside with a special thumbturn or from one side only with a single cylinder. The key can only be removed when the hardened hookbolt is fully locked or retracted. LC306X is the microswitch version of the lock. The switch changes the status when the hookbolt moves from unlocked to locked position. 46, Security locks for narrow profile doors ABLOY® LC306 10 5,5 4 Luettelopiirustus LC306 29/30.5/35 900059 ABLOY LC306H ® Security lock case (comparable with security grade 5 according to EN 12209) with hookbolt, reinforced against pulling loads for narrow profile sliding doors. Operates with key from either side with a double cylinder or from outside with a cylinder and inside with a special thumbturn or from one side only with a single cylinder. The key can only be removed when the hardened hookbolt is fully locked or retracted. LC306HX is the microswitch version of the lock. The switch changes the status when the hookbolt moves from unlocked to locked position. Striker plate LP708 Finish Fe/ZL Cylinder ABLOY® C, N, T, U Fire resistance – Mortise standard Please see page 61 ABLOY® LC307 Security lock case (comparable with security grade 5 according to EN 12209) for narrow profile doors. Operates with key from either side with a double cylinder or from outside with a cylinder and inside with a thumbturn or from one side only with a single cylinder. The key can only be removed when the hardened hookbolt is fully locked or retracted. LC307X is the microswitch version of the lock. The switch changes the status when the hookbolt moves from unlocked to locked position. Striker plate Finish Cylinder Fire resistance Mortise standard 4655, LP707 Fe/ZL ABLOY® N, T, U, SCAND – Please see page 61 33 A Security locks for narrow profile doors ABLOY® LC307H Security lock case (comparable with security grade 5 according to EN 12209) with hookbolt, reinforced against pulling loads for narrow profile sliding doors. Operates with key from either side with a double cylinder or from outside with a cylinder and inside with a thumbturn or from one side only with a single cylinder. The key can only be removed when the hardened hookbolt is fully locked or retracted. LC307HX is the microswitch version of the lock. The switch changes the status when the hookbolt moves from unlocked to locked position. Striker plate Finish Cylinder Fire resistance Mortise standard LP708 Fe/ZL ABLOY® N, T, U, SCAND – Please see page 61 Lock cases for narrow profile doors ABLOY® LC300 Non-deadlocking mortise lock for narrow profile entrance doors. The lock is opened by a key or a thumbturn (or handles if in use). Can be used with electromechanical striker plate. The sliding button is locked in the MIDDLE position. LC300X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 ABLOY® LC301 Automatically deadlocking lock for narrow profile emergency exit doors. The lock can be opened either with a key (outside and inside) or by using an emergency thumbturn (sliding snib in UP position). Latchbolt can be retained inside the lock case (sliding snib in DOWN position). Sliding snib is released only when turning the key. LC301X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance – Mortise standard Please see page 62 34 Lock cases for narrow profile doors ABLOY® LC301F Automatically deadlocking lock for fire resisting narrow profile emergency exit doors. The lock can be opened either with a key (outside and inside) or by using an emergency thumbturn. There is no sliding snib. Automatic deadlocking when the door is closed. LC301FX is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 ABLOY® LC302 Automatically deadlocking lock for narrow profile doors. Function is determined by sliding snib on forend: UP position = automatic deadlocking. Opened by a key from either side, or by a thumbturn from inside. MIDDLE position = lock is latched and operates also with handles. DOWN position = latchbolt is retained inside the lock case. Sliding snib is released only when turning the key (or thumbturn). LC302X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance – Mortise standard Please see page 62 ABLOY® LC303 Mortise latch for narrow profile doors with lever handle function only. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 35 Lock cases for narrow profile doors ABLOY® LC305 Automatically deadlocking lock for narrow profile doors. Primarily for doors which must always be latched (e.g. fire doors) and where deadlocking is needed. Function is determined by a sliding snib on forend: UP position = automatic deadlocking. Operates by a key (or a thumbturn) from either side. MIDDLE position = lock is latched and operates also with handles. DOWN position = not in use. Sliding snib is released only when turning the key (or thumbturn). LC305X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 Double cylinder lock cases for narrow profile doors ABLOY® LC130 Double cylinder lock case with an automatic deadlocking for narrow profile doors. Automatic deadlocking when the door is closed. The lock is opened with a key or a thumbturn. The cylinder and thumbturn which is used more is recommended to be installed higher up. The lock can be fitted with a thumbturn and/or a one sided or a double sided cylinder. The lower cylinder is installed upside down due to the construction of the lock. LC130X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 ABLOY® LC131 36 Double cylinder lock case with an automatic deadlocking for narrow profile doors equipped with a door closer. Function is determined by sliding button on forend: UP/MIDDLE position = automatic deadlocking. Operates by a key or a thumbturn. DOWN positon = latchbolt is retained inside the lock case. Sliding snib is released only when turning the key (or thumbturn). The cylinder and thumbturn which is used more is recommended to be installed higher up. The lock can be fitted with a thumbturn and/or a one sided and a double sided cylinder. The lower cylinder is installed upside down due to the construction of the lock. LC131X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance – Mortise standard Please see page 62 Double cylinder lock cases for narrow profile doors ABLOY® LC132 Double cylinder lock case, which is latching always when closing the door. The lock is opened with a key or a thumbturn. The lock can be used with electromechanical striker plate. The cylinder and thumbturn which is used more is recommended to be installed higher up. The locks can be equipped with a thumbturn and/or a one sided or a double sided cylinder. The lower cylinder is installed upside down due to the construction of the lock. LC132X is the microswitch version of the lock. The switch changes it’s status when the latchbolt protrudes 9 mm or more. Striker plate 4613, 4614, LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, SCAND Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Please see page 62 Exit locks for narrow profile doors ABLOY® LE310 Exit lock case with automatic deadlocking latchbolt for profile doors with one blade. The door is opened from outside with a lever handle. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The latchbolt protrudes 14 mm. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocked, the lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Day latching, the lock can be opened from outside by lever handle also. LE310X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. Striker plate Finish Cylinder Fire resistance Mortise standard LP702, LP703 Fe/ZL ABLOY® C, N, T, U, EI115-EI160 and EI215-EI260 Mortise for profile door lock cases 37 Exit locks for narrow profile doors ABLOY® LE314 Exit lock case with automatic deadlocking latchbolt for profile doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The lock is deadlocked always when the door is closed. The latchbolt protrudes 14 mm. LE314X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. Striker plate LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, Fire resistance EI115-EI160 and EI215-EI260 Mortise standard Mortise for profile door lock cases ABLOY® LE315 Exit lock case with automatic deadlocking latchbolt for profile doors with one blade. The door is opened from outside with a door pull. The lock case fulfils the requirements of the European standard for exit products SFS-EN179 and SFS-EN1125 and the requirements of the lock case standard SFS-EN12209. The lock is always opened from the inside by a lever handle, push pad or panic bar. The latchbolt protrudes 14 mm. Deadlocking is controlled by a snib in the front plate. Using of the snib is normally blocked. The snib is released by turning the key. Snib position: UP = Deadlocked The lock can be opened from outside by key only and from inside by a lever handle, push pad or panic bar. DOWN = Latchbolt is retained inside the lock case. LE315X is the microswitch version of the lock. The switch changes the status when latchbolt is deadlocked. 38 Striker plate LP702, LP703 Finish Fe/ZL Cylinder ABLOY® C, N, T, U, Fire resistance – Mortise standard Mortise for profile door lock cases Installation accessories ABLOY® 2050 installation box Surface mounted ABLOY® 2050 installation box is specially designed to be used on glass doors or other door constructions where normal mortice installation is not possible. All ABLOY® interior door locks (e.g. ABLOY® 2011, ABLOY® 2014 or ABLOY® 4260) made to fit in a mortice prepared according to standard SFS 5210 can be installed in this box. The delivery includes an installation box in two parts, insulating films to protect the glass, backing plate and installation parts. Striker plate for wooden door frame 0045, 0055, 0068, 0068B Striker plate for double door or glass screen 0050 Finish Fe/Mme, Fe/Har, Fe/Cr Drilling scheme please see page 63 ABLOY® 2051 installation box Surface mounted ABLOY® 2051 installation box is specially designed to be used on glass doors, gates or other door constructions where normal mortice installation is not possible. All ABLOY®-lock cases (e.g. ABLOY® 4190 series, excl. 4291) made to fit in a mortice prepared according to standard SFS 5209 can be installed in this box. The delivery includes an installation box in two parts, insulating films to protect the glass, backing plate and installation parts. Striker plate for wooden door frame 4690, 4691, LP711, LP714, LP721, LP731 Striker plate for double door or glass screen 0051 Striker plate for double door or glass screen with ABLOY® 4960, 0052 Finish Fe/Mme, Fe/Har, Fe/Cr Drilling scheme please see page 63 Transfer device ABLOY® 518 The surface mounted ABLOY® 518 transfer device can be used to combine two different key or cylinder systems and it can easily be installed also on existing locks of different types. The device can be used to combine ABLOY® C, N, T, U with ABLOY® C, N, T, U ABLOY® N, T, U with SCAND cylinders or SCAND with SCAND NB. Fittings to be ordered separately 39 Installation accessories Rounding pieces When the mortise is made by a drill, router or milling machine the tooling traces can be covered by rounding pieces. Finish = ABS/Cr 402424 = For striker plate 0036 402423 = For lock ABLOY® 428 Escutcheons 963 (lock SL928, 428) Finish Ms/Cr, Ms/Hcr, Ms/KiLa 964 (lock SL928 , 428) Finish Ms/Cr, Ms/Hcr, Ms/KiLa 962 (lock SL905) Finish Ms/Cr, Ms/Hcr, Ms/KiLa 961 (lock SL905) Finish Ms/Cr, Ms/Hcr, Ms/KiLa Cover plates 023 Finish Ms/Cr, Ms/HaLa 40 024 Finish Ms/Cr, Ms/HaLa 025 Finish Ms/Cr, Ms/HaLa Installation accessories Cover front plates 7640 Finish Fe/Cr, Fe/Hcr, Ms/HaLa, Ms/KiLa, Rst 7641 Finish Fe/Cr, Fe/Hcr, Ms/HaLa, Ms/KiLa, Rst 7691 Finish Zn/Cr 7694 Finish Zn/Cr 1 130 20 7690 Finish Zn/Cr Luettelop iirustus 7641 901018 0 Keys 2011 Length 43, 72 mm SL905 Length 47, 60 mm 2014 Length 48, 68 mm Folding key SL905 Length 47 mm 2040 Length 39 mm Square key SL928, 428, 451S Length 43, 53, 69 mm Hexagonal key 41 Installation accessories Striker plates 0029 0031/36 0031/40 0036 0043 0045 0031/41 0034, 0034/12 0046 Mortise please see page 65 0050 0051 0052 left 0052 right 0053 0055 35 -16 42 .5 15 14 41 100 1,5 Striker plates 0053 and 0055 havea 2,5 mm adjustment by which the function of the door can be optimized. 0050, 0051, 0052 mortise please see page 63 Vastarauta 0053 Installation accessories Striker plates 0065 0068 0068B 0078 0079 4662 4666 4690 4691 The striker plate is equipped with a box covering the mortise. Mortise please see page 65 4613 4614 4655 4667 4669 4673 37 22 35 190 35 1,5 12, 5 25,5 61,5 4,5 43 Luettelopiirustus 4673 vastarauta Installation accessories Striker plates 152 LP703 60,8 60,8 LP710 LP 707, LP708 mortise please see page 63, 64 33 33 LP711 Luettelop iirustus LP702 LP712 901030 Luettelop iirustus LP703 901031 LP713 0 0 LP710 and LP720 series have a 5 mm and LP730 series a 3 mm adjustment range. The adjustment is made by turning two screws in the forend of the striker plate by a screwdriver. Mortise please see page 64 LP714 44 LP717 LP708 5 2,5 Adjustable striker plates The striker plates have a patented stepless and slipless adjusting mechanism, by which the function of the seal can be optimized in all circumstances. This makes the door comfortable to use. LP707 30,5 LP702 152 4693 30,5 4692 LP718 LP719 LP719l Installation accessories Striker plates LP721 LP722 LP760R LP760L 3 3 LP731 LP732 LP763 31 31 8 LP723 31 8 8 3 5,5 -9, 5 23 148 128 8 230 210 8 LP780 44 52 6,5 8 6,5 54 8 45 37 5 27, 54 6,5 5,5 -9, 5 45 5 27, 5 27, 40 40 8 37 230 210 23 LP781 Ka ta logritning LP760R 901023 1 LP780 and LP781 mortise please see pageKa 65ta logritning LP760L 901024 1 Ka ta logritning LP763 901027 1 45 Hinges Drill-in hinges for windows M8x35/12 Material: steel. Finishes: white, galvanized. M8x25/12 HOP for aluminium casement Material: steel. Finishes: white, galvanized. Hinges for interior doors 6540 door part Material: steel/plastic. Finishes: white, brass coloured, silver coloured. 6540KS frame part Material: steel Finishes: white, brass coloured, silver coloured, chromed, bright brass. 6540KS is vertically adjustable +/- 2 mm. Symmetrical hinge for non-rebated interior doors. 5538 door part Material: steel/plastic Finishes: white, brass coloured, silver coloured. FT-65KS 46 Material: steel Finishes: white, brass coloured, silver coloured, chromed, bright brass. FT-65KS is vertically adjustable +/- 3 mm. Symmetrical hinge for rebated interior doors. Door part M6/12x22, galvanized steel. Hinges NTR110x30T-CE Material: steel Finishes: galvanized, chrome plated. NTR 110x30T is vertically adjustable +3 mm (adjusting piece S=1 mm). Journal supported lift-off hinge for rebated fire doors and inner doors of public premises NTR110x30TKSS-CE Material: steel Finishes: galvanized, chrome plated. NTR 110x30TKSS is vertically adjustable +4/-1,5 mm and laterally adjustable + 3 mm. Journal supported lift-off hinge for rebated fire doors and inner doors of public premises NTR110x30TMRKSS-CE Material: steel Finishes: galvanized, chrome plated. NTR 110x30T is vertically adjustable +4/-1,5 mm, laterally adjustable +3 mm and burglary proof. Journal supported lift-off hinge for rebated fire doors and inner doors of public premises Hinges for exterior doors 110x36KSS-F-CE Material: steel Finishes: white, brass coloured, galvanized/lacquered, galvanized/yellow lacquered. 110x36KSS is vertically adjustable +/- 3 mm, laterally adjustable + 3 mm and burglary proof. Symmetrical hinge for non-rebated exterior doors. 47 Hinges Hinges for exterior doors MARK CHANGE DATE/CHANG. DATE/ACC. N3248-110TMKSS-CE Material: steel. Finishes: silver coloured. 110 N3248-110TMKSS is vertically adjustable -1/+4 mm, laterally adjustable +3 mm and burglary proof. 5 2, R1 Journal supported lift-off hinge for non-rebated exterior doors. 36 1 49 MARK 49 CHANGE PART DATE/CHANG. DRAW.NO/DELIV. DESCRIPTION PRODUCT Abloy Oy Tampere factory An ASSA ABLOY Group Company This document is and stays our exclusive property and as such is not to be copied in whole or in part nor made available to any third party without our permission. MATERIAL DIMENSIONS N3248-110TMKSS OB. RATIO DESIGN 1:1 CHECK INFORMATION 1 IF NOT OTHERWISE MENTIONED MEASUREMENTS DOES NOT INCLUDE COATING DATE/ACC. PCS AREA cm² WEIGHT g INFORMATION 2 Finishes: silver coloured. INFORMATION 3 110 N3548-110TMKSS is vertically adjustable -1/+4 mm, laterally adjustable +3 mm and burglary proof. Journal supported lift-off hinge for non-rebated exterior doors. R1 2 36 1 3,5 17 49 MARK 49 CHANGE PART DATE/CHANG. DRAW.NO/DELIV. DESCRIPTION MATERIAL PRODUCT N3548-110TMKSS Abloy Oy Tampere factory An ASSA ABLOY Group Company This document is and stays our exclusive property and as such is not to be copied in whole or in part nor made available to any third party without our permission. IF NOT OTHERWISE MENTIONED MEASUREMENTS DOES NOT INCLUDE COATING DATE/ACC. DIMENSIONS OB. RATIO DESIGN 1:1 CHECK PCS ACC. INFORMATION 1 REPLACE INFORMATION 2 AREA cm² WEIGHT g Journal supported lift-off hinge for non-rebated exterior doors. 36 49 49 DRAW.NO/DELIV. DESCRIPTION PRODUCT Abloy Oy Tampere factory An ASSA ABLOY Group Company This document is and stays our exclusive property and as such is not to be copied in whole or in part nor made available to any third party without our permission. MEASUREMENTS WITHOUT AN TOLERANCE ARE HANDLED AS MIDDLE COARSE IN SFS-EN22768-1 > 0,5 - 6 = ± 0,1 >6 - 30 = ± 0,2 > 30 - 120 = ± 0,3 > 120 - 400 = ± 0,5 > 400 - 1000 = ± 0,8 48 IF NOT OTHERWISE MENTIONED MEASUREMENTS DOES NOT INCLUDE COATING 3,1 1 16 PART MATERIAL DIMENSIONS RATIO N3248-110TMRKSS INFORMATION 1 INFORMATION 2 INFORMATION 3 Material: steel. N3248-110TMRKSS is vertically adjustable -1/+4 mm, laterally adjustable +3 mm and burglary proof. ,5 2 R1 N3248-110TMRKSS-CE Finishes: silver coloured. INFORMATION 3 110 MEASUREMENTS WITHOUT AN TOLERANCE ARE HANDLED AS MIDDLE COARSE IN SFS-EN22768-1 > 0,5 - 6 = ± 0,1 >6 - 30 = ± 0,2 > 30 - 120 = ± 0,3 > 120 - 400 = ± 0,5 > 400 - 1000 = ± 0,8 N3548-110TMKSS-CE Material: steel. ACC. REPLACE ,5 MEASUREMENTS WITHOUT AN TOLERANCE ARE HANDLED AS MIDDLE COARSE IN SFS-EN22768-1 > 0,5 - 6 = ± 0,1 >6 - 30 = ± 0,2 > 30 - 120 = ± 0,3 > 120 - 400 = ± 0,5 > 400 - 1000 = ± 0,8 3,1 16 OB. PCS DESIGN CHECK ACC. REPLACE AREA cm² WEIGHT g Hinges Hinges for glass doors FL-75PSSD Material: aluminium.. Finishes: brass coloured, silver coloured. FL-75PSSD is laterally adjustable +/- 3 mm. FL-75PSSGD Material: aluminium. Finishes: brass coloured, silver coloured. FL-75PSSGD is laterally adjustable +/- 3 mm. Free opening of M9 door is 800 mm (FOP hinge) Concealed hinges CH-40KSS Material: zinc. Finishes: satin nickel, nickel, brass. Concealed hinge for non-rebated interior door. Maximum door weight 40 kg. CH-80KSS Material: zinc. Finishes: satin nickel, nickel, brass Concealed hinge for non-rebated interior door. Maximum door weight 80 kg. 49 Hardware Letter plates Letter plate DF60+63 Material: stainless steel. For use with apartment front doors, as well as on front doors of houses. Includes a name plate, and can also be installed vertically. Letter plate DF61 Material: stainless steel. Surface finish: polished. Surface finish: polished. For use with apartment front doors, as well as on front doors of houses. Can also be installed vertically. Flap DF63 Material: stainless steel. Surface finish: polished. Used in combination with letter plates DF60 and DF61. Letter plate PRIMO 31 Material: aluminium/plastic. Finishes: silver-anodized Al/Aho, brass-anodized Al/Me. Letter plate PRIMO 31 is tested in Finland for EI15 and EI30 –fire doors and dB25, dB30 and dB35 –decibel doors. Can be used as a replacement for ABLOY® DF60+63 or 464 -letter plates. 50 Hardware Quick bolt Quick bolt DF3000, DF3001, DF3100 Stainless, DF3101 Stainless Material: visible parts brass/other parts steel or stainless steel. Surface finishes: chrome, satin chrome, polished/lacquered. Quick bolt DF3000 is used for securing the closed half of metal profile and wooden doors without a middle casing. In closed position the bolt opens only by pulling the handle down. A clear sticker instructs the proper use. The bolt has a new quick attachment of locking bars which makes the installation easier. In the basic versions DF3000 ja DF3100 St the position of the locking bars can adjusted 7 mm, 11-18 mm from the surface of the door. The fitting depth of the bolt is only 31 mm. For certain door profiles special versions DF3001 and DF3101 St are suitable where the fitting depth of the locking bars is 32–35 mm from the door surface.The fitting depth of the bolt is then 46 mm. The satin-chromed DF3100 and DF3101 bolts made from stainless steel are particularly suitable for humid areas such as on boats or in dairies. All the locking parts of the bolt are made from stainless steel and have satin chromed surface finish. Quick bolt DF900 Material: brass. Surface finishes: polished, chrome. Surface fitted model with two way function. Used for securing wooden and metal profile double doors. Wood screws, 2 pcs striker plates, 4 pcs guides included in D.I.Y. packs 51 Hardware Flush bolt Flush bolt DF849 Material: zinc. Surface finishes: chromium plated, brass-plated. Flush fitting model. For use with wooden double doors to secure the closed half of the door, 2 pcs/door. Adjustable striker plate is plastic. Flush bolt DF330 Material: steel. Surface finish: galvanized. Flush fitting model with two-way function; rods are fitted to the bolt with M8 threading (rods not included in delivery). Used for bolting metal profile double doors, 1 pc/door. 52 Mortises Locks for interior doors SFS 5210 SS 81 73 82 2011, 2014, 2016, 2020, 2040, 4238, 4249, 4260, 4570, 9456 2011, 2014, 2040 with DIN fittings 2018 with ABLOY® 001PZ fittings 2018 with normal standard fittings The mortise measures are normative. 53 Mortises Locks for interior doors 2018 with ABLOY® 004PZ fittings 2018 with ABLOY® 010PZ fittings LC291 LC291 asymmetrical mortise +2 40 0 22 A +0,2 4 0 +2 40 0 +0,5 0 A 11 20 Rm Rm a ax x2 0 11 +0,5 0 +0,2 4 0 +0,5 0 +0,5 22 0 Esiporaus ruuville Pilot hole for the screw 60,5 ±0,5 +1 0 +4 171 0 225 B Lukko rung o n up o tuksen keskiko hta = o vilevyn keskiko hta Center o f the m o rtise = Center o f the d o o r lea f B 12 ±0,5 70 ±0,5 +1 0 +4 0 171 225 60,5 ±0,5 Esip o ra us ruuville Pilo t ho le fo r the sc rew B Lukkorungon upotuksen keskikohta = ovilevyn keskikohta Center of the mortise = Center of the door leaf B Ava utum issivu Hing e sid e 51 ±1 +2 84 0 Avautumissivu Hinge side A A-A 51 ±1 84 Lukko rung o n up o tuksen keskiko hta Mo rtise c enter o f the lo c k c a se 22 22 Up otusp iirustus LC291 901037 54 A A-A Lukkorungon upotuksen keskikohta Mortise center of the lock case Sivup o ra ukset m ä ä rä ytyvä t lukko ko hta isesti Sid e d rilling s a c c o rd ing to lo c k typ e B-B +2 0 0 The mortise measures are normative. Sivuporaukset määräytyvät lukkokohtaisesti Side drillings according to lock type B-B Upotuspiirustus LC291 epäsymetrinen 901038 A Mortises Locks for interior doors 4291 4291 asymmetrical mortise 4202 4203 Section A – A Section A – A Section B – B Section B – B The mortise measures are normative. 55 Mortises Locks for interior doors 4230 Section A – A Section B – B Lock cases for wooden / steel doors 4207 4208 Section A – A Section A – A Section B – B Section B – B 56 The mortise measures are normative. Mortises Lock cases for wooden / steel doors 4292 4293 Section A – A Section A – A Section B – B Section B – B 4297 4298 Section A – A Section B – B The mortise measures are normative. 57 Mortises OneFit-mortise LC190, LC193, LC194, LC195, LC197 LC290, LC960 LC102 LE180, LE181; LE183, LE184; LE185, LE186 Lock cases for wooden / steel doors SFS 5208, SS 81 73 83 LC200, LC202, LC203, LC204, LC205, LC206, LC208, LC209, LC209A, LC210, LC211, 4181, 4865 58 SFS 5209 LC100, 4190, 4190T, 4194, 4195, 4195T, 4197, 4290, 4960, E4190, E4194, E4195 The mortise measures are normative. Mortises ABLOY® LC200 with wc fittings 4272 Lock cases for wooden / steel doors 4272MP The mortise measures are normative. 59 Mortises Double cylinder lock cases for wooden / steel doors LC120, LC122, LC125, LC127 LC121, LC121T, LC123 Security and additional locks for wooden/steel doors SL905, SL928, 428 60 SL905MP, SL928MP The mortise measures are normative. Mortises Security and additional locks for wooden/steel doors 4232 4232MP Security locks for narrow profile doors LC307, LC307H ¤ ¤ £ £ £ £ £ ¤ ¤ ¤ £ LC306, LC306H, ¡ ¡ ¡ ¡ ¢ ¡ ¡ ¡ ¡ The mortise measures are normative. 61 LC301F, LC302, LC303, LC305 ¡ ¢ ¢ ¢ ¢ ¢ ¢ Double cylinder £¤¥ £¤¥ £¤¥ £¤¥ £¤¥ ¦ £¤¥ £¤ ¦ ¦ ¥ lock cases for narrow profile doors LC130, LC131, LC132 62 ¡ LC300, LC301, Mortises Lock cases for narrow profile doors The mortise measures are normative. Mortises Installation box 2050 2051 Striker plates 0050, 0051, 0052 LP707 The mortise measures are normative. 63 Mortises Striker plates LP708 LP721, LP722, LP723 64 LP710, LP711, LP712, LP713, LP714, LP717, LP718, LP719, LP719l LP731, LP732 The mortise measures are normative. Mortises Striker plates LP780 0036 LP781 0065 Multipoint locking applications The mortise measures are normative. 65 An ASSA ABLOY Group brand Abloy Oy is one of the leading manufacturers of locks, locking systems and architectural hardware and the world’s leading developer of products in the field of electromechanical locking technology. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. 8811706 6/2014 www.abloy.com Abloy Oy Björkboda factory 25860 BJÖRKBODA, Finland Tel. + 358 20 599 4402 + 358 20 599 4436 Fax + 358 20 599 4249 + 358 20 599 4117
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project