FE408xxxAx

FE408xxxAx
March 2009
FE408005AA
FE408020AA
FE408020XA
FE408045XA
FE408100XA
FE408200XA
Optinet™ Quick Start Guide
Optinet—the bandwidth shaping, content filtering
BLACK BOX
appliance.
®
Customer
Support
Information
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
Optinet Quick Start Guide
TRADEMARKS USED IN THIS MANUAL
Black Box and the Double Diamond logo are registered trademarks, and Optinet is a trademark, of BB
Technologies, Inc.
Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
724-746-5500 | blackbox.com
Table of Contents
Installing Optinet ......................................................................................................................... 1
Gathering Initial Information ......................................................................................................................................... 1
Connecting to Optinet .................................................................................................................................................... 3
Running the Setup Wizard ............................................................................................................................................. 4
Cutting-Over .................................................................................................................................................................. 5
Accessing Optinet .......................................................................................................................................................... 7
Customer Support and Feedback ............................................................................................. 8
Getting Help .................................................................................................................................................................. 8
End User License Agreement (EULA) & Warranty ................................................................... 9
We‘re here to help! If you have any questions about your application
or our products, contact Black Box Tech Support at 724-746-5500
or go to blackbox.com and click on “Talk to Black Box.”
You’ll be live with one of our technical experts in less than 20 seconds.
ii
Optinet Quick Start Guide
Federal Communications Commission and Industry Canada Radio Frequency Interference
Statements
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause inter ference to radio communication. It has been tested and found to
comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to oper
ate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set out in the Radio
Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.
724-746-5500 | blackbox.com
-
Optinet Quick Start Guide
Instrucciones de Seguridad
(Normas Oficiales Mexicanas Electrical Safety Statement)
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca
de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.
Todo otro servicio deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico
sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes
que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros
aparatos (incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como
se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados
sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
724-746-5500 | blackbox.com
Installing Optinet
In this guide you will learn how to perform an initial installation of Optinet. The following
topics will be covered:
•
Gathering Initial Information
•
Configuring Connectivity
•
Running the Setup Wizard
•
Cutting Over
•
Accessing Optinet
Optinet is a powerful network device that is relatively easy to set up in any network
environment using the instructions in this document and the Setup Wizard. Please read and
understand all configuration and installation considerations before proceeding.
If you have questions or are unsure about the installation of Optinet, please contact your
Authorized Black Box Network Services Reseller and/or the person responsible for the
service of your network.
Gathering Initial Information
Under this section is listed the information you will need to know before installing Optinet.
For a more detailed explanation of terms and alternative configuration steps, please consult
the User Guide. Begin by reviewing the information and filling out the following table for
documentation. You will need the subsequent information:
1
License Key
Licenses that have been purchased with your system will ship as a license key on a card in the
Documentation & Accessories box or be delivered via email at the time of purchase. Locate this
information to enable the licenses on your system during the setup process.
License Key:
Model Number :
Serial Number:
Licensed Network Nodes
IP Configuration
If you are unsure of the following fields, the Setup Wizard will detect available addresses and settings
within your network via DHCP. You may copy over these settings during the Setup Wizard.
Optinet (Bridge) IP address:
Subnet Mask:
Default Gateway (WAN Side) IP address:
DNS Server IP address:
Auxiliary/Management Port IP address:
The Auxiliary/Management Port IP address can not be in an active subnet in your network.
Auxiliary/Management Port Subnet Mask:
Total Download Bandwidth (in Kbps):
Total Upload Bandwidth (in Kbps):
Time Zone:
Amounts used in the Total Download Bandwidth and Total Upload Bandwidth will
restrict total throughput through Optinet. Please make sure the amounts you enter in
these fields are correct.
2
Email Settings
In order for Optinet to send email alerts, the email server listed below must be configured to relay
messages from Optinet.
System Alerts & Broadcasts email address
(System Administrator):
Email Server Hostname or IP address
(optional):
Remote Subnets
Optinet will identify and monitor all network traffic native to its local subnet. If you have a routed
network (VLANs, different network addresses, etc.), please note the network addresses with the
appropriate CIDR notation.
Subnet address (CIDR notation):
Subnet address (CIDR notation):
Subnet address (CIDR notation):
Once you have this information, you’re ready to make your initial connections to Optinet.
Connecting to Optinet
The next step is to power on and connect to Optinet from a local management
workstation/laptop. You will also need to connect Optinet to your network.
Running the Setup Wizard requires an active Internet connection from the
network where Optinet will be installed. If you do not have an active Internet
connection available, or you do not wish to use the Setup Wizard, please consult the section
Using Alternative Configuration Methods in the User Guide.
3
1. Connect a cross-over cable (included in your Accessories Kit) from Optinet’s LAN port
to the network port on your workstation/laptop.
2. Connect a straight-through cable from Optinet’s WAN port to an empty port on your
local network switch.
Figure 1: Optinet Configuration Connectivity
3. Write down the existing IP settings of your local workstation/laptop in order that you
can easily change them back when configuration is complete.
4. Change you local workstation/laptop IP settings. You will need to change the IP
settings on your local workstation/laptop to communicate with the default settings of
Optinet:
a. Default IP Address—192.168.1.80
b. Default Subnet Mask—255.255.255.0
The suggested settings for the local workstation/laptop are the following:
c. IP Address—192.168.1.81
d. Subnet Mask—255.255.255.0
Running the Setup Wizard
1. To access the Setup Wizard, open Microsoft’s Internet Explorer (IE) 6 or 7 and enter
http://192.168.1.80 in the address bar.
2. Login to the system using:
a. Default User Name: admin (all lowercase)
b. Default Password: blackbox (all lowercase)
4
3. Please read and accept the EULA agreement.
4. The Welcome Screen is then displayed automatically on new systems as well as on
systems that have been reset to factory defaults. Read the information displayed in
the Welcome Screen and select Next>>.
Figure 2: The Setup Wizard Welcome Screen
5. Using the information you collected in the section Gathering Initial Information,
complete the steps within the Setup Wizard. Select Next>> when the page fields
are complete. Optinet will test the settings of each step and if successful will allow
you to proceed.
6. The final step in the Setup Wizard allows you to confirm and, if necessary, edit your
configuration. This step will also check for updates and will automatically retrieve
and install them. Major firmware upgrades will result in a reboot of your system
when complete.
Please note that advanced configuration options such as Directory Integration or Ethernet
Settings require additional steps not covered in the Setup Wizard. For information on these
topics, please review their corresponding chapters in the User Guide.
Cutting-Over
Only perform these next steps when network traffic can be momentarily
interrupted.
Now that you have finished the Setup Wizard, you are ready to place Optinet inline with
Internet traffic. Optinet requires all Internet traffic to pass through its bridge interface,
unless the device is configured in Proxy Mode. If you are planning to configure Optinet in
Proxy Mode, you will need to consult the User Guide.
5
For typical installations you will need to follow the next steps and physically place Optinet
inline with your network’s traffic. In general, Optinet is installed in between the
Firewall/WAN Router and the Core Network Switch.
1. Remove the cables connected to Optinet’s WAN and LAN ports.
2. If you modified your local workstation/laptop IP settings, you will need to change
your settings back to their original IP settings.
3. Locate the connection between the Core Network Switch and the Firewall/WAN
Router. Unplug the cable from the Firewall/WAN Router and connect it to the LAN
port on Optinet.
4. Using the cross-over cable, connect the WAN port of Optinet to the now open port on
the Firewall/WAN Router that was previously used by the Core Network Switch.
Figure 3: Optinet Installation Connectivity
5. Verify that the cross-over cable is plugged into Optinet’s WAN port and the
Router/Firewall.
6. Verify that the straight-through cable is plugged into Optinet’s LAN port and the Core
Network Switch. Optinet should now be sitting inline with your Internet traffic.
7. Verify that Optinet’s WAN and LAN ports are posting solid green lights and blinking
amber lights (Optinet may take up to 5 minutes to complete this step).
8. Verify that local workstations can access the Internet by opening a Web browser and
navigating to several Web sites.
If you are able to browse to the Internet, you have completed the installation of Optinet.
The device should now be sitting inline with your Internet traffic and monitoring all network
traffic.
6
Accessing Optinet
After completing the configuration and installation processes, you can access Optinet by
using the IP address you assigned to the device during the Setup Wizard.
1. Open Microsoft’s IE 6 or 7 and navigate to http://IP address assigned.
2. Login using the default credentials (listed under the section Running Setup Wizard).
3. When you login to Optinet the Home Page will display. This page provides a
snapshot of system health, filtering effectiveness, current firmware versions,
subscription settings, as well as links to administration of your new system.
You have now completed installing Optinet. For details on how to manage Optinet and
generate reports on traffic, please consult the User Guide. The User Guide can be found on
the CD included in your Documentation & Accessories Kit or under the Help Menu tab on
Optinet’s Graphical User Interface (GUI).
We strongly recommend that you create a new administrative login, and change the
default login password to limit access to Optinet’s management interface. Select the
Manage -> System Access -> Logins link to make these changes.
7
Customer Support and Feedback
Getting Help
For additional help, please consult the User Guide or Black Box Network Services Support at
724-746-5500. Additionally, you can contact your Authorized Black Box Network Services
Reseller for support.
For more information contact Black Box Network Services at 724-746-5500.
Please have the following information ready:
•
•
•
•
•
•
•
Total bandwidth
Total number of network nodes
Optinet model and serial number
Optinet firmware version
A network topology diagram
Presence of VLANs, proxy servers, remote subnets
What symptoms or issues you are experiencing
We welcome your feedback and comments on Optinet. Contact us and let us know. Please
identify your Optinet model and tell us how we can reach you.
8
End User License Agreement (EULA) & Warranty
PLEASE READ THE FOLLOWING BEFORE USING THE ACCOMPANYING PRODUCT. YOU
SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING THE
ACCOMPANYING SOFTWARE AND HARDWARE (“APPLIANCE”). THE USE OF THE PRODUCT
IS LICENSED FOR USE ONLY AS SET FORTH BELOW. IF YOU DO NOT AGREE TO THE TERMS
AND CONDITIONS OF THIS AGREEMENT, DO NOT USE THE PRODUCT. IF YOU USE ANY
PART OF THE SOFTWARE AND HARDWARE, SUCH USE WILL INDICATE THAT YOU ACCEPT.
License Grant
Subject to the terms and conditions of this License, you are granted a nonexclusive right
and license to use the Software on the Appliance. In addition, (1) you may not reverse
engineer, decompile, disassemble or modify the Software or Appliance, except and only to
the extent that such activity is expressly permitted by applicable law notwithstanding this
limitation; and (2) you may not transfer rights under this License unless such transfer is
part of a permanent sale or transfer of the Product, and you transfer at the same time the
Appliance and Software to the same party or destroy such materials not transferred, and
the recipient agrees to this License. No license is granted in any of the Software’s
proprietary source code.
You may make a reasonable number of copies of the electronic documentation
accompanying the Software for each Software license you acquire, provided that, you must
reproduce and include all copyright notices and any other proprietary rights notices
appearing on the electronic documentation.
Black Box Network Services and their suppliers reserve all rights not expressly granted
herein.
Intellectual Property Rights
The Software and Appliance is protected by copyright laws, international copyright treaties,
and other intellectual property laws and treaties. This license does not grant you any rights
to patents, copyright, trade secrets, trademarks or any other rights with respect to the
Software and Appliance. Black Box Network Services and its suppliers retain all ownership
of, and intellectual property rights in (including copyright), the Software and Appliance.
However, certain components of the Software are components licensed under the GNU
General Public License (version 2). You may obtain a copy of the GNU General Public
License at http:/www.fsf.org/copyleft/gpl.html. Black Box will provide source code for any of
9
the components of the Software licensed under the GNU General Public License upon
request. Additionally, this product includes software developed by the OpenSSL Project for
use in the OpenSSL Toolkit. (http://www.openssl.org/).
Export Restrictions
You agree that you will not export or re-export the Appliance, Software, any part thereof, or
any process or service that is the direct product of the Appliance or Software in violation of
any applicable laws or regulations of the United States or the country in which you obtained
them.
U.S. Government Restricted Rights. The Software and related documentation are provided
with Restricted Rights. Use, duplication, or disclosure by the Government is subject to
restrictions set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013 or subparagraphs (c) (1) and (2) of the
Commercial Computer Software–Restricted Rights at 48 C.F.R. 52.227-19, as applicable, or
any successor regulations.
Term and Termination
This License is effective until terminated. The License terminates immediately if you fail to
comply with any term or condition. In such an event, you must destroy all copies of the
Software. You may also terminate this License at any time by destroying the Product.
Governing Law and Attorney’s Fees
This License is governed by the laws of the State of Utah, USA, excluding its conflict of law
rules. You agree that the United Nations Convention on Contracts for the International Sale
of Goods is hereby excluded in its entirety and does not apply to this License. In any action
or suit to enforce any right or remedy under this License or to interpret any provision of this
License, the prevailing party will be entitled to recover its costs, including reasonable
attorneys’ fees.
Entire Agreement
This License constitutes the entire agreement between you and Black Box Network Services
and its suppliers with respect to the Software, and supersedes all other agreements or
representations, whether written or oral. The terms of this License can only be modified by
express written consent of both parties. If any part of this License is held to be
unenforceable as written, it will be enforced to the maximum extent allowed by applicable
law, and will not affect the enforceability of any other part.
BLACK BOX NETWORK SERVICES DISCLAIMS ANY AND ALL OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. OTHER
THAN AS STATED HEREIN, THE ENTIRE RISK AS TO SATISFACTORY QUALITY,
PERFORMANCE, ACCURACY, AND EFFORT IS WITH YOU. ALSO, THERE IS NO WARRANTY
AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST
INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR
THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING
ON, BLACK BOX NETWORK SERVICES.
NO LIABILITY FOR CERTAIN DAMAGES. EXCEPT AS PROHIBITED BY LAW, BLACK BOX
NETWORK SERVICES SHALL HAVE NO LIABILITY FOR COSTS, LOSS, DAMAGES OR LOST
OPPORTUNITY OF ANY TYPE WHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOST OR
ANTICIPATED PROFITS, LOSS OF USE, LOSS OF DATA, OR ANY INCIDENTAL, EXEMPLARY
SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER UNDER CONTRACT, TORT, WARRANTY
OR OTHERWISE ARISING FROM OR IN CONNECTION WITH THIS LICENSE OR THE USE OR
PERFORMANCE OF THE SOFTWARE. IN NO EVENT SHALL BLACK BOX NETWORK SERVICES
BE LIABLE FOR ANY AMOUNT IN EXCESS OF THE PURCHASE PRICE AND/OR ANY LICENSE
FEES PAID TO BLACK BOX NETWORK SERVICES UNDER THIS LICENSE. SOME STATES AND
10
COUNTRIES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS LIMITATION MAY NOT APPLY TO
YOU.
Hardware Warranty
Black Box Network Services Corp. warrants your Black Box Network Services product to be
in good working order and to be free from defects in workmanship and material (except in
those cases where materials are supplied by the Purchaser) under normal and proper use
and service for the period of one (1) year from the date of purchase from an Authorized
Black Box Network Services Reseller. In the event that this product fails to meet this
warranty within the applicable warranty period, and provided that Black Box Network
Services confirms the specified defects, Purchaser’s sole remedy is to have Black Box
Network Services, at Black Box Network Services’ sole discretion, repair or replace such
product at the place of manufacture, at no additional charge other than the cost of freight of
the defective product to and from the Purchaser. Repair costs and replacement products will
be provided on an exchange basis and will be either new or reconditioned. Black Box
Network Services will retain, as its property, all replaced parts and products.
Notwithstanding the foregoing, this hardware warranty does not include service to replace
or repair damage to the product resulting from accident, disaster, abuse, misuse, electrical
stress, negligence, any non-Black Box Network Services modification of the product except
as provided or explicitly recommended by Black Box Network Services, or other cause not
arising out of defects in material or workmanship. This hardware warranty also does not
include service to replace or repair damage to the product if the serial number or seal or
any part thereof has been altered, defaced, or removed. If Black Box Network Services does
not find the product to be defective, the Purchaser will be invoiced for said inspection and
testing at Black Box Network Services’ then current rates, regardless of whether the product
is under warranty.
11
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 20 seconds away at 724-746-5500 or blackbox.com.
About Black Box
Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You’ll find everything
from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by
free, live 24/7 Tech support available in 20 seconds or less.
© Copyright 2009. All rights reserved.
724-746-5500 | blackbox.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement