Shark NV70 Specification

Shark NV70 Specification
NV70
Owner’s Guide
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 1
13-02-28 1:48 PM
This manual covers model number:
NV70 26
TECHNICAL SPECIFICATIONS
Voltage: 120V.
Watts: 1200W
Amps: 10A
Hertz: 60Hz
Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names
may be trademarks of their respective owners.
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 2
13-02-28 1:48 PM
Contents
Thank you for
purchasing
the Shark®
Navigator™
DLX.
Important Safety Instructions2
Getting Started4
Using the Vacuum6
Cleaning with the Vacuum Accessories7
Emptying the Dust Cup Assembly8
Proper Care of Your Vacuum9
Troubleshooting10
Checking for Blockages11
Maintenance12
Warranty and Registration13
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 1
1
13-02-28 1:48 PM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK®
NAVIGATOR™ DLX VACUUM, BASIC
SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK® NAVIGATOR™ DLX
VACUUM.
POLARIZED PLUG:
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fit into a polarized outlet only one way.
Do not force into the outlet or try to
modify the plug to fit.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
GENERAL ELECTRICAL SAFETY:
1. Unplug from electrical outlet when not in use
and before servicing.
2.
DO NOT use vacuum with a damaged cord
or plug. If appliance is not working as it
should, has been dropped, damaged, left
outdoors, or dropped into water, return it to
EURO-PRO Operating LLC for examination,
repair, or adjustment.
3.
DO NOT pull or carry vacuum by the cord.
4.
DO NOT unplug by pulling on cord; to
unplug, grasp the plug, not the cord.
5.
DO NOT handle plug or appliance with
wet hands.
WARNING:
TO REDUCE THE RISK OF ELECTRIC
SHOCK OR INJURY DO NOT USE
OUTDOORS OR ON WET SURFACES.
6.DO NOT run the vacuum over the power
cord.
7.
DO NOT use the cord as a handle.
8.
DO NOT close a door on the cord.
9.
DO NOT pull cord around sharp corners.
The use of an extension cord is not
recommended.
10.DO NOT leave appliance when plugged in.
11.Keep cord away from heated surfaces.
12.Turn off all controls before plugging or
unplugging vacuum cleaner.
13.Always turn off this appliance before
connecting or disconnecting motorized
nozzle.
14.Store your appliance with the power cord
secured around the two cord holders-as
shown in the storage instructions.
2
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 2
13-02-28 1:48 PM
HOSE ATTACHMENTS:
DUST CUP/FILTERS/ACCESSORIES:
1.
DO NOT use if air flow is restricted; if the air
paths, the hose, or the accessories become
blocked, turn the vacuum cleaner off. Remove
all obstructions before you turn on the
unit again.
Before turning on the vacuum:
2.Keep the end of the hose and accessory
openings away from face and body.
1.Make sure that all filters are thoroughly dry
after routine cleaning.
2.Make sure that dust cup and all filters are in
place after routine maintenance.
3.Make sure accessories are free of blockages.
3.Keep cleaning tools and hose suction
openings away from hair, face, fingers,
uncovered feet,or loose clothing.
4.Only use filters and accessories provided by
EURO-PRO Operating LLC. [Failure to do so
will void the warranty.]
4.Only use manufacturer’s recommended
attachments.
GENERAL CLEANING:
1. DO NOT pick up large-sized objects.
GENERAL USE:
1.Use only as described in this manual.
2.
DO NOT put any objects into openings. DO
NOT use with any opening blocked; keep
free of dust, lint, hair, and anything that may
reduce air flow.
3.Keep your work area well lit.
4.Keep the vacuum moving over the carpet
surface at all times to avoid damaging the
carpet fibers.
5.
DO NOT place vacuum on unstable surfaces
such as chairs or tables.
6.
DO NOT allow young children to operate
the vacuum or use as a toy. Close attention is
necessary when used by or near children.
7.
DO NOT use vacuum cleaner if it has
been dropped, damaged, left outdoors, or
submerged in water. Return to EURO-PRO
Operating LLC for examination, repair, or
adjustment.
8.
DO NOT use without dust cup and/or filters
in place.
2.
DO NOT pick up hard or sharp objects such
as glass, nails, screws or coins that could
damage the vacuum cleaner.
3.
DO NOT pick up smoking or burning objects
such as hot coals, cigarette butts, or matches.
4.
DO NOT pick up flammable or combustible
materials such as lighter fluid, gasoline, or
kerosene or use vacuum in areas where they
may be present.
5.
DO NOT pick up toxic solutions such as
chlorine bleach, ammonia, or drain cleaner.
6.
DO NOT use in an enclosed space where
vapors are present from paint, paint thinner,
moth-proofing substances, flammable dust or
other explosive or toxic materials.
7. DO NOT vacuum up any liquids.
8.
DO NOT immerse vacuum cleaner in water
or other liquids.
9.
DO NOT use outdoors or on wet surfaces;
use only on dry surfaces.
10.Use extra care when cleaning on stairs.
SAVE THESE
INSTRUCTIONS
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 3
3
13-02-28 1:48 PM
Getting Started
8
C
D
4
A
5
7
E
B
2
3
F
G
H
Your Shark® Navigator™ DLX
is easy to assemble:
WHAT’S IN THE BOX YOU JUST
OPENED:
1Lay your vacuum body on a
level surface.
A
B
C
D
E
F
G
H
2Slide the electrical connection
from the power nozzle into the
main body to click into place.
4
Vacuum Body
Floor Power Nozzle
Handle Assembly
Super Stretch Hose
Cleaning Wand
Pet Hair Brush
Dusting Brush
Crevice Tool
3Connect the hose from the main
body to the power nozzle; push
with a slight turning motion to
create a snug fit.
5Secure the handle assembly in
place with included nut/bolt
(shipped attached to handle
assembly).
6Place the vacuum in the upright
position.
7Insert the Cleaning Wand into
the center post on the tool
caddy.
8Store the Crevice Tool, Dusting
Brush on the back of the unit.
4Slide the handle assembly
into the upright unit aligning
the hose hook on the handle
assembly with the power cord
hooks on the back of the unit.
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 4
13-02-28 1:48 PM
9
10
c
a
d
b
9 Attach the Super Stretch Hose:
a) Snap hose into swivel
connector
b) Route under anti-tip hook
to prevent vacuum from
tipping
10To store the vacuum:
11 To carry the vacuum:
When storing your vacuum,
wind the cord around the two
cord holders and secure with
cord clip:
With the unit in the standing
position, lift by the Dust Cup
Assembly Handle (carry handle).
• Quick Cord release at the
top of the unit – place in the
upright position.
c) Route over upper hose
holder
d) Press securely onto cleaning
wand with handle
• Cord holder near the base –
turn it until it is pointing down.
IMPORTANT:
Insert the hose into the wand.
This completes the air path and
enables suction to reach the
Floor Power Nozzle.
T o release the cord, turn the Quick
Cord release to the left or right.
CAUTION: When lifting or
carrying, DO NOT press Dust
Cup Assembly release button.
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 5
5
13-02-28 1:48 PM
Using the Vacuum
IMPORTANT: To protect your
carpets, the brushroll will only
turn on when you have pulled
the handle back towards you and
released the Floor Power Nozzle.
Release suction for
easier push and pull
on high pile carpets
and area rugs.
4
3 Power Switch
Settings
OFF
Suction Release
6
Bare Floors /
Tools
Carpets
2
Your Shark® Navigator™ DLX
Vacuum can be used to clean bare
floors or carpets – with the click of a
switch.
Stand the vacuum into the upright
position.
Plug in the vacuum.
1Start with the Power Switch in the
“O" - Off position.
2Place your foot on the Floor Power
Nozzle and pull handle towards
you.
3Set the Power Switch to desired
cleaning setting.
4Push the power cord into the
groove on the handle and then
secure the power cord into the
cord clip.
6
5Press the On/Off switch to the“I"
position to vacuum bare floors or
cleaning with the hose (straight
suction only) or to the "II"
position to engage the motorized
floor brush (for vacuuming carpets
and rugs).
6
Due to the huge suction
power of this vacuum, it may
become necessary to adjust
the suction release on the
hose. If the vacuum is difficult
to push or pull or if it is
lifting up area rugs, adjust the
suction release by opening
the valve at the top end of
the hose. Close the suction
release valve for maximum
suction when vacuuming
floors or when using the pet
hair power brush.
IMPORTANT:
Your Brushroll Indicator Light
will illuminate solid green when
the brushroll is on, or solid red if
there is a blockage. This feature is
designed to protect your Lifetime
Belt that powers your brushroll.
See Checking for Blockages
on page 11.
NOTE: The height of your power
nozzle has been optimized
for easy pushing and superior
cleaning on all floor types, so there
is no need to make any height
adjustments as you transition to
different floor & carpet types.
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 6
13-02-28 1:48 PM
Cleaning with the Vacuum Accessories
1
2
3
4
5
3
4
2 Using the Cleaning Wand:
5
Before cleaning with your
accessories:
Stand vacuum into upright position.
Secure Super
Stretch Hose in
the anti-tip hose
hook to prevent
tipping.
Stand the vacuum into upright
position.
Vacuum Accessories
Your vacuum comes with a Super
Stretch Hose and Cleaning Wand.
Use one or the other to attach your
cleaning accessories.
Push the selected tool into the
end of the Cleaning Wand.
3 Pet Hair Power Brush
4 Dusting Brush
1 Using the Super Stretch Hose:
5
Crevice Tool
Stand the vacuum into upright
position.
To order additional parts and accessories,
go to www.sharkclean.com or call
1-800-798-7398.
Select the “I" - On position for suction only cleaning.
Remove the hose from the
Cleaning Wand.
DO NOT pull vacuum cleaner
around by the hose.
Push the selected tool into the
hose connector.
Remove the Cleaning Wand
(with hose attached) from the
unit.
DO NOT overextend the hose.
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 7
7
13-02-28 1:48 PM
Maintenance
CAUTION:
Unplug the vacuum; failure to do
so might result in electric shock.
For best results empty the Dust Cup
Assembly after each use, as needed
during prolonged usage or when it
reaches the MAX fill line.
DO NOT OVERFILL.
Turn vacuum off before emptying.
2
1
3
To empty the Dust Cup:
1Grip carry handle and press
the Dust Cup release button to
remove.
2
Option A: For Quick Empty:
Insert Dust Cup deep inside
trash receptacle to contain dust
and debris.
Press the bottom Dust Cup
release button; tap container
gently to dislodge and release
dust and debris.
Snap door in place.
Important: If the Dust Cup
Door does not swing open after
pressing the release button,
push the door open using the
bottom door tabs.
8
3
Option B: For Allergy Sufferers:
Wrap a trash bag around the
Dust Cup leaving space at the
bottom for the door to swing
open.
Locate the Dust Cup Door
release button within the trash
bag and press to release as you
shake the dust cup to empty
dust and debris.
Note: Some dust and debris
may remain in the top of your
dust cup on or near the metal
screen. It is not necessary to
completely remove this material
before continuing to vacuum;
Shark® advanced cyclonic
action will sweep the metal
screen clean once you begin to
refill your dust cup.
Snap the bottom door in place.
Note: Option B can also be
performed outside of the home
to further minimize releasing
dust back into the air. Carry just
the Dust Cup and trash bag
outside.
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 8
13-02-28 1:48 PM
COMPONENT
MAINTENANCE SCHEDULE
1 Dust Cup
Empty each time you vacuum.
2 Pre-Motor Foam Filter
Rinse and air dry every month under normal use.
3 Pre-Motor Felt Filter
Rinse and air dry every month under normal use.
4 Post-Motor HEPA Filter
Clean once a year under normal use.
DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.
Pre-Motor
Foam Filter
IMPORTANT: Loss of Suction may
occur if foam filter is not cleaned
every month. Rinse and allow to air dry
completely. Also, tap loose dirt off filter
between washes as needed.
Foam filters may appear dirty after use this is normal.
Felt Filter
Post Motor
HEPA Filter
To clean the post-motor HEPA filter:
1
Remove the filter cover from the front of the
vacuum by pulling up on the tab and pulling the
cover away from the vacuum.
2 Take out the HEPA filter by pulling it straight out.
To clean the pre-motor filters:
1 Remove the dust cup.
2
Pull the 2 filters out from the top of the motor
base.
3
Rinse the filters thoroughly in lukewarm water until
the water runs clear.
DO NOT put the filters in the washing machine or
dishwasher.
3
Turn the HEPA filter over so that the dirty side is on
the bottom and vigorously tap it clean against a
garbage can to remove any dust.
4
Wash the HEPA filter under the tap using lukewarm
water with the dirty side face down until the water
runs clear.
DO NOT put the HEPA filter in the washing
machine or dishwasher.
NOTE: The material in the filter will discolor over
time. This is NORMAL and will not affect the
performance of the filter.
NOTE: The material in the filters will discolor
over time. This is NORMAL and will not affect the
performance of the filters.
5 A
llow the HEPA filter to air dry for 24 hours. Do
not use a hair dryer or other heating methods to
dry.
4
Squeeze out excess water and let air-dry for at
least 24 hours before replacing. Do not use a hair
dryer or other heating methods to dry.
6
Once the HEPA filter is dry, replace it back into the
vacuum.
5
Place the felt filter in first, then the foam filter.
6 Replace the dust cup.
7 R eplace the cover by inserting the two tabs into
the holes at the bottom and then swinging the
cover up until it clicks into place.
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 9
9
13-02-28 1:48 PM
Troubleshooting
WARNING:
to reduce the risk of electric shock, the power cord must be disconnected before
performing maintenance/troubleshooting checks.
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Vacuum is not
picking up dirt.
Check filters to see if they need cleaning. Follow instructions for rinsing
and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose and hose connections for blockages; clear blockages if required.
If dust cup is empty, and attachment inlets are clear, check for other
blockages. (See “Checking for Blockages” for instructions.)
Vacuum lifts scatter rugs
(lightweight, movable
rugs).
Suction is powerful. Take care when vacuuming scatter-type rugs or rugs with
delicately sewn edges. Open the suction release on the hose to decrease
suction power.
Check filters to see if they need cleaning. Follow instructions for rinsing
and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)
Airflow is restricted. No
suction or light suction.
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzles and accessories for blockages; clear
blockages if required.
Close the suction release on the hose to increase suction power.
If dust cup is empty, and attachment inlets are clear, check for other
blockages. (See “Checking for Blockages” for instructions.)
Motorized floor brush
has become jammed or
has shut off.
Immediately turn off and unplug vacuum, disconnect the nozzle and remove
blockage before reconnecting and turning vacuum back on. (See “Checking
for Blockages” for instructions.)
This vacuum cleaner is equipped with a motor protective thermostat. If for
some reason your vacuum overheats, the thermostat will automatically turn
the unit off. Should this occur, perform the following steps to restart the
motor thermostat:
1. Move the On/Off switch to the “O” (Off) position.
2. Unplug the vacuum.
Vacuum turns off on its
own.
3. Empty the dust cup and clean filters. (See “Maintenance” sections for
instructions.)
4. Check for blockages in hose, accessories and inlet openings.
(See “Checking for Blockages” for instructions.)
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Turn the On/Off switch to the “I” (On) position to restart the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
10
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 10
13-02-28 1:48 PM
Checking for Blockages
2
1
4
3
Unplug the vacuum before
checking for blockages.
Reassemble all parts securely
before operating vacuum.
Blockages may cause your vacuum
to overheat and shut down. If so,
clear the blockages, then follow the
instructions for Resetting the
Motor Thermostat on page 12.
WARNING: Never insert sharp
objects into any opening to clear
an obstruction.
IMPORTANT: Damages caused
while clearing or attempting to
clear blockages are not covered
under your product’s limited
warranty.
1 Dust Cup Air Duct:
Stand vacuum into upright
position.
3
Floor Power Nozzle Hose
Connector:
Lay vacuum flat.
Remove Dust Cup Assembly and
empty Dust Cup if necessary.
Remove Nozzle Hose and check
for clogs.
Disconnect the Super Stretch
Hose.
Push the Hose Connector back
onto the Floor Power Nozzle.
Check Air Duct behind Dust Cup
for clogs; clear before replacing
Dust Cup Assembly.
4 Hose:
2
Intake Opening behind the
Brushroll:
Lay the vacuum flat to expose
brushroll.
Check opening behind the
brushroll for clogs.
Stand vacuum upright.
Remove hose from both the unit
and Cleaning Wand ends.
Inspect both ends and the length
of the hose for clogs.
Return the hose to the unit.
Clear the opening.
Clear the brushroll; use scissors
to carefully cut away threads,
hair or other debris that might
be trapped in the bristles.
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 11
11
13-02-28 1:48 PM
Maintenance
a
Rotating
Brush
Cleaning The Pet Hair Brush
1 S lide the locking latch (a)
forward and tilt the bottom
cover upward to remove.
Cleaning The Motorized Floor
Brush
When your motorized floor brush
needs cleaning or locks onto an
object, it automatically shuts
down to prevent damage to your
lifetime belt. The indicator light
will illuminate red warning you
to turn off the vacuum and clear
blockage immediately. The light will
reset itself once blockage has been
cleared and power has been cycled
on/off or vacuum has been locked in
the upright position.
1
Detach the motorized floor
brush from the detachable
canister.
2Inspect the opening underneath
and the rotating brush. If a
build-up of debris is present,
remove it. Carefully cut
anything wound around the
rotating brush with scissors.
Avoid damaging or cutting the
bristles.
12
Resetting the Motor Thermostat
Your Shark® Navigator™
DLX Vacuum is equipped with
a protective Motor Thermostat. If
the motor should overheat, the
thermostat shuts off the power.
To reset the Motor Thermostat:
Move the Power Button to the
“O” – Off position.
Unplug the vacuum.
Check for clogged hose or filter;
unclog hose and replace filter.
Refer to Checking for Blockages
on page 11.
Wait 45 minutes for vacuum to cool;
then plug in the vacuum.
Turn the Power Switch to the
“I” – On position to start the
vacuum.
Note: If vacuum still does not start,
contact Customer Service at:
1-800-798-7398.
2 C
arefully remove any blockage
or debris and cut away any
build-up of hair or string
wrapped around the rotating
bristle brush with scissors.
3 T o reassemble, insert the tabs
on the front edge of the bottom
cover into the matching holes
in the top half and tilt it back
down until it clicks into place.
Ordering Replacement Parts
To order additional parts and
accessories, go to
www.sharkclean.com
or call 1-800-798-7398.
PART
Super Stretch Hose
Dusting Brush &
Crevice Tool
PART NO.
152FFJ
1115FC
Foam & Felt Filters
XFF80
Hepa Filter
XHF80
Turbo brush
143FFJ
Cleaning Wand
114FFJ
TOLL FREE: 1-800-798-7398
NV70_26_IB_E_130228_1.indd 12
13-02-28 1:48 PM
Euro-Pro Five-Year (5) Limited Warranty
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of
five (5) years from the date of the original purchase, when utilized for normal household use, subject to the following
conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid to:
• U.S.: EURO-PRO Operating LLC
For customer service support call 1-800-798-7398
or visit www.sharkclean.com
• Canada: EURO-PRO Operating LLC
4400 Bois Franc, St. Laurent, Québec H4S 1A7
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or
replace it free of charge. Proof of purchase date and $19.95 to cover the cost of return shipping and handling must
be included.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require
replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit
at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been
tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse,
abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover
damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product
or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional
warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly
assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental
or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of
incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or
province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase
date and to attach tag to item before packing with your name, complete address and phone number
with a note giving purchase information, model number and what you believe is the problem
with item. We recommend you insure the package (as damage in shipping is not covered by your
warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly
striving to improve our products, therefore the specifications contained herein are subject to change
without notice.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10)
days of purchase. You will be asked to provide the store name, date of purchase and model number along with your
name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering
you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
www.sharkclean.com
NV70_26_IB_E_130228_1.indd 13
13
13-02-28 1:48 PM
Euro-Pro Operating LLC
USA: Newton, MA 02459
CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7
English: 1-800-798-7398
www.sharkclean.com
Copyright © Euro-Pro Operating LLC 2013
Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC.
All other brand names may be trademarks of their respective owners.
Printed in China
Illustrations may differ from actual product.
NV70.E.130228.1
NV70_26_IB_E_130228_1.indd 14
13-02-28 1:48 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement