Emerson | MVME51005E | COMPUTING - Artesyn Embedded Technologies

COMPUTING
MVME5100
Data Sheet
The MVME5100 is designed to meet
the needs of OEMs servicing the defense
and aerospace, industrial automation
and medical market segments
ƒƒ MPC7410 or MPC750 microprocessor
with 32 KB/32 KB L1 cache
ƒƒ Up to 2MB of secondary ƒ
backside cache
ƒƒ 100 MHz frontside bus
ƒƒ Up to 512MB of on-board ECC
SDRAM expandable up to 1GB with
optional RAM500 memory expansion
modules
ƒƒ 17MB flash memory
ƒƒ Dual IEEE P1386.1 compatible ƒ
32/64-bit PMC expansion slots
ƒƒ 64-bit PCI expansion mezzanine
connector allowing up to four ƒ
more PMCs
ƒƒ Dual 16550 compatible async ƒ
serial ports
ƒƒ Dual 10BaseT/100BaseTX Ethernet
ƒƒ 32 KB NVRAM and time-of-day clock
with replaceable battery backup
ƒƒ Four 32-bit timers and one ƒ
watchdog timer
ƒƒ On-board debug monitor
ƒƒ Single VME slot even when fully
configured with two PMC modules
and both add-on memory mezzanines
Freescale MPC7410 or MPC750 VME SBC
The Artesyn Embedded Technologies MVME5100 series features the Freescale MPC7410
or MPC750 microprocessor with 32 KB/32 KB L1 cache. It uses the Artesyn PowerPlus II
Architecture to support full PCI throughput of 264MB/s without starving the processor from
its memory.
Based on an integrated PCI bridge-memory controller ASIC, PowerPlus II enables 582 MB/s
memory read bandwidth and 640MB/s burst write bandwidth.
The MVME5100 is designed to meet the needs of OEMs servicing the defense and aerospace,
industrial automation and transportation market segments.
MVME5100 Data Sheet
MVME5100 Block Diagram
SDRAM Expansion
256MB
L2 Cache
1 or 2MB
60x
Arbiter
Vcore
REG
Processor
MPC7410
MPC750
Hawk ASIC
SDRAM Expansion
64 or 256MB
Flash
1MB
Serial
16550
Serial
ECC SDRAM
Up to 512MB
Flash
16MB
Serial
16550
RJ-45
BUF
100 MHz Memory Bus
+3.3V
REG
X-Bus
RTC
NVRAM
64-bit/33 MHz Local PCI Bus
FP I/O
PCI
Expansion
PMC2
Ethernet
82559ER
FP I/O
PMC1
VME
Universe II
Ethernet
82559ER
Rows A & C
64 pins
Rows D & Z
64 pins
RJ-45
P2
Overview
I/O Compatibility
Historically, Artesyn has offered two tracks in its PowerPC®
Architecture VME portfolio. The first track (which includes the
MVME2600/2700) provides typical single-board computer I/O
features including Ethernet, SCSI, multiple serial ports, a parallel
port and a single PMC slot. The on-board I/O is routed to P2
and made available to the user via Artesyn MVME761 or
MVME712M transition boards. The second track (which includes
the MVME2300/2400) offers limited on-board I/O (Ethernet and a
single serial port both via the front panel) but provides dual PMC
slots enabling maximum user I/O customization.
The MVME5100 merges the best features of both tracks enabling
the OEM to support varying I/O requirements with the same base
platform, simplifying part number maintenance, technical expertise
requirements and sparing.
RJ-45
P1
P2 I/O Modes
The MVME5100 supports two, jumper-configurable P2 I/O modes;
PMC and IPMC. PMC mode is backward compatible with the
MVME2300/MVME2400. In PMC mode, 64 pins from PMC slot 1
and 46 pins from PMC slot 2 are available onP2 for PMC rear I/O.
In IPMC mode, the MVME5100 supports legacy MVME761 or
MVME712M I/O modules (with limited PMC I/O) when an IPMC761 or
IPMC712 PMC card is populated in PMC slot 1. In this configuration,
PMC slot 2 contains some signals that are reserved for extended SCSI.
IPMC Modules
The IPMC761 and IPMC712 are optional add-on PMC modules
that provide backward compatibility with previous-generation
Artesyn products (such as MVME2600 and MVME2700) using the
MVME761 or MVME712M transition board. IPMC modules provide
rear I/O support for the following:
ƒƒ One single-ended Ultra Wide SCSI port
ƒƒ One parallel port
ƒƒ Four serial ports (2 or 3 async and 1 or 2 sync/async, depending
on module)
With this PMC card configuration, the memory mezzanine, one
PMC slot and the PMCspan are still available, providing support for
OEM product customization.
MVME5100 Data Sheet
Software Support
PMC P11 & P12
PCI
PIB
WB-554
ISA
ESCC
85230
CIO
8536
P2 MUX
P2 MUX
PAL
(IPMC761)
SER4 (Sync)
SER3 Sync (761) Async (712)
Parallel
COM2
Super I/O
National
COM1
16-bit SCSI
SCSI
LSI
PMC P14 & P15
Transition Modules
The MVME761 transition module provides industry standard
connector access to the IEEE 1284 parallel port, a 10BaseT or
100BaseT port via an RJ-45 connector, two DB-9 connectors
providing access to the asynchronous serial ports configured as
EIA-574 DTE and two HD-26 connectors providing access to the
sync/async serial ports. These serial ports, labeled as Serial 3
and Serial 4 on the faceplate of the MVME761, are individually
user-configurable as EIA-232, DCE or DTE via the installation of
Artesyn Serial Interface Modules (SIMs). A P2 adapter board
provides interface signals to the MVME761 transition module.
Two separate P2 adapter boards are available: one for 3-row
backplanes and one for 5-row backplanes. The 3-row P2 adapter
board provides connection for 8-bit SCSI. A 5-row P2 adapter
board supports 16-bit SCSI and PMC I/O.
The MVME712M transition module provides industry standard
connector access to the Centronics parallel port, a narrow SCSI
port, and four DB-25 connectors providing access to the
asynchronous/synchronous serial ports jumper configurable as
EIA-232 DCE or DTE. A P2 adapter board provides interface
signals to the MVME712M transition module. The 3-row P2
adapter board also provides connection for 8-bit SCSI. To gain
access to the additional user-definable I/O pins provided via the
5-row VME64 extension connector, a special P2 adapter board is
available. This adapter panel replaces the traditional 3-row P2
adapter board and extends its capability by providing access to the
PMCI/O pins.
Firmware Monitor
Firmware must fulfill the traditional functions of test and initialization
and provide operating system boot support. The MVME5100
firmware monitor exceeds these requirements with a proven
monitor from the embedded VME leader. It expands features like
powerup tests with extensive diagnostics, as well as a powerful
evaluation and debug tool for simple checkout or when high-level
development debuggers require additional support. All this is
included with the MVME5100 firmware; plus it supports booting
both operating systems and kernels.
Operating Systems and Kernels
MVME5100 supports booting a variety of operating systems,
including VxWorks from Wind River Systems, Inc., Integrity from
Green Hills, and Linux from a variety of partners.
Specifications
Processor
MPC7410
MPC750
Clock Frequency:
400/500 MHz
450 MHz
On-chip Cache (I/D):
32 K/32 K
450 MHz
On-chip Cache (I/D):
32 K/32 K
32 K/32 K
Secondary Cache:
2MB
1MB
Main Memory
ƒƒ Type: PC100 ECC SDRAM with 100 MHz bus
ƒƒ Capacity: Up to 512MB on-board, expandable to 1.5GB with
RAM500 memory mezzanines
ƒƒ Single Cycle Accesses: 10 Read/5 Write
ƒƒ Read Burst Mode: 7-1-1-1 idle; 2-1-1-1 aligned page hit
ƒƒ Write Burst Mode: 4-1-1-1 idle; 2-1-1-1 aligned page hit
ƒƒ Architecture: 64-bit, single interleave
Flash Memory
ƒƒ Type: EEPROM, on-board programmable
ƒƒ Capacity: 1MB via two 32-pin PLCC/CLCC sockets;
16 MB surface mount
ƒƒ Read Access (16MB port): 70 clocks (32-byte burst)
ƒƒ Read Access (1MB port): 262 clocks (32-byte burst)
MVME5100 Data Sheet
NVRAM
PCI Expansion Connector
ƒƒ Capacity: 32 KB (4 KB available for users)
ƒƒ Address/Data: A32/D32/D64
ƒƒ Cell Storage Life: 50 years at 55° C
ƒƒ PCI Bus Clock: 33MHz
ƒƒ Cell Capacity Life: 5 years at 100% duty cycle, 25° C
ƒƒ Signaling: 5 V
ƒƒ Removable Battery: Yes
ƒƒ Connector: 114-pin connector located on the planar of
the MVME5100
VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)
ƒƒ Controller: Tundra Universe
ƒƒ DTB Master: A16–A32; D08–D64, BLT
ƒƒ DTB Slave: A24–A32; D08–D64, BLT, UAT
ƒƒ Arbiter: RR/PRI
Power Requirements
(not including power required by PMC or IMPC modules)
MVME5100
+5 V ± 5%
+12 V ± 10%
–12 V ± 10%
3.0 A typ.
8.0 mA typ.
2.0 mA
ƒƒ Interrupt Handler/Generator: IRQ 1–7/Any one of seven IRQs
Board Size
ƒƒ System Controller: Yes, jumperable or auto detect
ƒƒ Height: 233.4 mm (9.2 in.)
ƒƒ Location Monitor: Two, LMA32
ƒƒ Depth: 160.0 mm (6.3 in.)
Counters/Timers
ƒƒ Front Panel Height: 261.8 mm (10.3 in.)
ƒƒ TOD Clock Device: M48T37V
ƒƒ Width: 19.8 mm (0.8 in.)
ƒƒ Real-Time Timers/Counters: Four, 32-bit programmable
ƒƒ Max. Component Height: 14.8 mm (0.58 in.)
ƒƒ Watchdog Timer: Time-out generates reset
Ethernet Interface
IPMC Modules
ƒƒ Controller: Two Intel® 82559ER
PMC Interface
ƒƒ Interface Speed: 10/100 Mbps
ƒƒ Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,
PN4 connectors
ƒƒ PCI Local bus DMA: Yes, with PCI burst
ƒƒ Connector: One routed to front panel RJ-45, one routed to front
panel RJ-45 or optionally routed to P2, RJ-45 on MVME761
Asynchronous Serial Ports
ƒƒ PCI Bus Clock: 33 MHz
ƒƒ Signaling: 5 V
ƒƒ Module Type: Basic, single-wide; P2 I/O
ƒƒ Controller: 16C550C UART
SCSI Bus
ƒƒ Number of Ports: Two, 16550 compatible
ƒƒ Controller: Symbios 53C895A
ƒƒ Configuration: RS-232 DTE/DCE
ƒƒ PCI Local Bus DMA: Yes, with PCI local bus burst
ƒƒ Async Baud Rate, bps max.: 38.4 K EIA-232, 115 Kbps raw
ƒƒ Asynchronous (8-bit mode): 5.0MB/s
ƒƒ Connector: One routed to front panel RJ-45, one on planar for
development use
ƒƒ Ultra SCSI: 20.0MB/s (8-bit mode), 40.0MB/s (16-bit mode)
Dual IEEE P1386.1 PCI Mezzanine Card Slots
ƒƒ Note: 16-bit SCSI operation precludes the use of some PMC
slot 2 signals
ƒƒ Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,
PN4 connectors
Synchronous Serial Ports
ƒƒ PCI Bus Clock: 33 MHz
ƒƒ Number of Ports: Two (IPMC761); one (IPMC712)
ƒƒ Signaling: 5 V
ƒƒ Configuration: IPMC761: TTL to P2 (both ports),
SIM configurable on MVME761; IPMC712: EIA-232 to P2
ƒƒ Power: +3.3 V, +5 V, ±12 V; 7.5 watts maximum per PMC slot
ƒƒ Module Types: Two single-wide or one doublewide, front panel
or P2 I/O
ƒƒ Controller: 85230/8536
ƒƒ Baud Rate, bps max.: 2.5 M sync, 38.4 K async
ƒƒ Oscillator Clock Rate (PCLK): 10 MHz/5 MHz
MVME5100 Data Sheet
Asynchronous Serial Ports
ƒƒ Controller: 16C550 UART; 85230/8536
ƒƒ Number of Ports: Two (IPMC761); three (IPMC712)
ƒƒ Configuration: EIA-574 DTE (IPMC761); EIA-232 (IPMC712)
ƒƒ Async Baud Rate, bps max.: 38.4 K EIA-232, 115 Kbps raw
Parallel Port
ƒƒ Controller: PC97307
Power Requirements
(Additional power load placed on MVME5100 series with IPMC
installed)
+5 V ±5%
+12 V ±10%
–12 V ±10%
MVME5100:
3.8 A max.
3.0 A typ.
8.0 mA typ.
2.0 mA typ.
MVME5110- 21xx:
3.8 A max.
3.1 A typ.
8.0 mA typ.
2.0 mA typ.
MVME5110- 22xx:
4.7 A max.
3.5 A typ.
8.0 mA typ.
2.0 mA typ.
ƒƒ Configuration: 8-bit bi-directional, full IEEE 1284 support;
Centronics compatible (minus EPP and ECP on MVME712M)
ƒƒ Modes: Master only
Transition Modules
I/O Connectors
MVME761
MVME712M
Asynchronous Serial Ports:
Two, DB-9 labeled as COM1 and COM2
Three, DB-25 labeled Serial 1, Serial 2 and Serial 3
Synchronous Serial Ports:
Two, HD-26 labeled as Serial 3 and Serial 4 (user-configurable
via installation of SIMs); two 60-pin connectors on MVME761
planar for installation of two SIMs
One, DB-25 labeled as Serial 4
Parallel Port:
HD-36, Centronics compatible
D-36, Centronics compatible
Ethernet:
10BaseT or 100BaseTX, RJ-45
Not available
SCSI:
8- or 16-bit, 50- or 68-pin connector via P2 adapter
8-bit, standard SCSI D-50
All Modules
Electromagnetic Compatbility (EMC)
Environmental
(Minimum of 400 LFM of forced air cooling is recommended for
operation in the higher temperature ranges.)
ƒƒ Intended for use in systems meeting the following regulations:
Operating
Non-operating
Temperature:
0 °C to +55 °C (inlet
air temp. with forced
air cooling*)
–40 °C to +85 °C
Humidity (NC):
5% to 90%
5% to 90%
Vibration:
2 Gs RMS,
20 – 2000 Hz random
6 Gs RMS,
20 – 2000 Hz random
•
U.S.: FCC Part 15, Subpart B, Class A (non-residential)
•
Canada: ICES-003, Class A (non-residential)
ƒƒ This product was tested in a representative system to the
following standards:
•
CE Mark per European EMC Directive 89/336/EEC with
Amendments; Emissions: EN55022 Class B; Immunity:
EN55024
Safety
All printed wiring boards (PWBs) are manufactured with a
flammability rating of 94V-0 by UL recognized manufacturers.
Demonstrated MTBF
(based on a sample of eight boards in accelerated stress environment)
ƒƒ Mean: 190,509 hours
ƒƒ 95% Confidence: 107,681 hours
MVME5100 Data Sheet
Ordering Information
All models are available with either VME Scanbe front panel (-xxx1) or IEEE 1101 compatible front panel (-xxx3).
Part Number
Description
Weight
MVME51005E-0161
450 MHz MPC750, 512MB ECC SDRAM, 17MB flash and 1MB L2 cache Scanbe 5E
0.37 kg
MVME51005E-0163
450 MHz MPC750, 512MB ECC SDRAM, 17MB flash and 1MB L2 cache IEEE 5E
0.42 kg
400/500 MHz MPC7410 Commercial Models
MVME51105E-2161
400 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache Scanbe 5E
0.42 kg
MVME51105E-2163
400 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache IEEE 5E
0.42 kg
MVME51105E-2261
500 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache Scanbe 5E
0.38 kg
MVME51105E-2263
500 MHz MPC7410, 512MB ECC SDRAM, 17MB flash and 2MB L2 cache IEEE 5E
0.42 kg
MVME712M Compatible I/O
IPMC7126E-002
Multifunction rear I/O PMC module; 8-bit SCSI, Ultra Wide SCSI, one parallel port, three async and one sync/async serial ports
MVME712M6E
Transition module connectors: One DB-25 sync/async serial port, three DB-25 async serial port, one AUI connector,
one D-36 parallel port, and one 50-pin 8-bit SCSI; includes 3-row DIN P2 adapter module and cable
MVME761 Compatible I/O
IPMC7616E-002
Multifunction rear I/O PMC module; 8-bit SCSI, one parallel port, two async and two sync/async serial ports
MVME7616E-001
Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel
port connector, one RJ-45 10/100 Ethernet connector; includes 3-row DIN P2 adapter module and cable (for 8-bit SCSI)
MVME7616E-011
Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel
port connector, and one RJ-45 10/100 Ethernet connector; includes 5-row DIN P2 adapter module and cable (for 16-bit
SCSI); requires backplane with 5-row DIN connectors
SIM232DCE6E
EIA-232 DCE Serial Interface Module 6E
SIM232DTE6E
EIA-232 DTE Serial Interface Module 6E
Related Products
PMCSPAN16E-002
Primary PMC expansion for MVME5100/5110/5500 w/Scanbe handles, 6E
PMCSPAN26E-002
Primary PMC expansion for MVME5100/5110/5500 w/IEEE handles, 6E
PMCSPAN16E-010
Secondary PMC expansion for PMCSPAN26E-002 w/Scanbe handles, 6E
PMCSPAN26E-010
Secondary PMC expansion for PMCSPAN26E-002 w/IEEE handles, 6E
RAM5006E-005
Stackable (top) 128MB ECC SDRAM mezzanine 6E
RAM5006E-015
Stackable (bottom) 128MB ECC SDRAM mezzanine 6E
RAM5006E-006
Stackable (top) 256MB ECC SDRAM mezzanine 6
RAM5006E-016
Stackable (bottom) 256MB ECC SDRAM mezzanine 6E
RAM5006E-010
Stackable (top) 512MB ECC SDRAM mezzanine 6E
RAM5006E-020
Stackable (bottom) 512MB ECC SDRAM mezzanine 6E
Documentation
V5100A/IH
MVME5100 Installation and Use
V5100A/PG
Programmer’s Reference Guide
VME761A/IH
MVME761 Transition Module Installation and Use
VME712MA/IH
MVME712 Transition Module Installation and Use
PPCBUGA1/UM
PPCBUGA2/UM
PPCBug Firmware Package User’s Manual (volumes one and two)
PPCDIAA/UM
PPCBug Diagnostics Manual
MVME5100 Data Sheet
Solution Services
Artesyn Embedded Technologies provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help
speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh.
PICMG, AdvancedTCA, ATCA and the AdvancedTCA logo are trademarks of PICMG. Service Availability is a proprietary trademark used under license. Intel and Xeon are trademarks of Intel Corporation
or its subsidiaries in the Unites States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other product or service names are the property of their
respective owners.
This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future
availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Artesyn Embedded Technologies may sell products. A prospective buyer
should exercise its own independent judgment to confirm the suitability of the products for particular applications. Artesyn reserves the right to make changes, without notice, to any products or information
herein which will, in its sole discretion, improve reliability, function, or design. Artesyn does not assume any liability arising out of the application or use of any product or circuit described herein; neither
does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Artesyn’s licensee, licensee’s transferees,
and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations.
WORLDWIDE OFFICES
Tempe, AZ U.S.A. +1 888 412 7832
Munich, Germany +49 89 9608 2552
Hong Kong
+852 2176 3540
Shanghai, China +86 21 3395 0289
Tokyo, Japan
+81 3 5403 2730
Seoul, Korea
+82 2 3483 1500
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc.
www.artesyn.com
MVME5100-D1 04/04/14
Download PDF