Elation | Event MHTM | User manual | Elation Event MHTM User manual

Elation Event MHTM User manual
Event Panel System™ Introduction
Unpacking: Thank you for purchasing the Event Panel System™ by
EVENT PANEL
SYSTEM
Elation Professional®. Every Event Panel System™ has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
fixture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without first
contacting customer support.
Introduction: The Elation Professional® Event Panel System™ is part
of a continuing pursuit for creating high quality affordable intelligent fixtures. The Event Panel System™ is a DMX intelligent LED color stage
wash. This fixture includes a battery pack/charger so that you are able
to take it on the go and not worry about a power outlet. This wash can
be used in a stand alone mode or connected in a Master/Slave configuration. The unit can also be controlled via DMX controller. This wash
has four operating modes: Sound Active mode, Auto mode, Program
mode, RGB mode, and DMX control mode.
Customer Support: Elation® provides a toll free customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.elationlighting.com for any comments
or suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
Voice:
(323) 582-3322
Fax: (323) 832-9142
E-mail: support@elationlighting.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
User Instructions
Elation Professional®
©
Rev. 4/11
6122 S. Eastern Ave.
Los Angeles CA. 90040
www.elationlighting.com
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
Elation®.
PLEASE recycle the shipping carton when ever possible.
©Elation
Lighting® - www.elationlighting.com - Event Panel System™ User Manual Page 2
Event Panel System™ General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Event Panel System™ •
•
•
•
•
•
•
•
Features
Battery Pack/Charger
288 Ultra Bright LEDs
Mulit-Colors
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
8 DMX Channel Modes: 2, 3, 4, 5, 6, 7, 14, & 26 DMX Channels
WR L.E.D. Remote
Event Panel System™
Warranty Registration
The Event Panel System™ carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.elationlighting.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact Elation® customer
support for a R.A. number.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 3
Event Panel System™
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required volt-
age for your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 17 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 4
POWER
Event Panel System™
Set Up
Event Panel System™
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned
aDMX512
DMX address of 1
DMX+,DMX-,COMMON
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
COMMON
REMOTE
CONTROL
1 Ground
DMX +
3
3
DMX -
1
2
SOUND
XLR Female Socket
2 Cold
2 Cold
3 Hot
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
1
2
Figure 2
OUTPUT
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
3 Hot
Pin 3 = Data True (positive)
Figure 3
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (-
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Figure 1
©Elation® - www.elationlighting.com - Event Panel System™ User Manual Page 5
OUTPUT
DMX +
3
Pin 2 = Data Compliment (negative)
COMMON
Data Cable (DMX Cable) Requirements (For DMX Operation):
2
INPUT
2
XLRINPUT
Male Socket
POWER
1
1
DMX512 OUT
3-PIN XLR
SOUND
DMX512
OUT
The Event Panel System™ can be controlled via
DMX-512
protocol.
The
3-PIN XLR
DMX Event Panel System™ can be a two, three, four, five, six, seven, 14,
and 26 channel DMX unit. The DMX address is set on the top panel of
the Event Panel System™. Your unit and your DMX controller require
an approved DMX-512 110 Ohm Data cable for data input and data
output (Figure 1). We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
DMX connector on either end of the cable. Also
remember that DMX cable must be daisy chained
and can not be split.
Set Up
DMX512
DMX+,DMX-,COMMON
Power Supply: The Elation® Event Panel System™ is a 100v ~ 220v
unit. Because of voltage setup of the unit you do not have to worry
about wall output voltage. This unit is compatible with all wall outputs.
SOUND
POWER
©Elation®
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
- www.elationlighting.com - Event Panel System™ User Manual Page 6
Event Panel System™
Operating Instructions
Note: To deactivate the Elation intro scroll, first make sure power
is off. With the power off, press and hold the SET UP, MODE and
DOWN buttons and turn the power ON all at the same time. To activate the Elation intro scroll, press and hold the SET UP, MODE, and
UP buttons and turn the power ON all at the same time.
Operating Modes:
You can use the Event Panel System™ in either a stand alone mode
or a master/slave configuration, there are 5 modes to choose from:
• Programs Mode - Select one of 14 different programs and adjust the different features of the program.
• Auto Run - The unit will automatically chase through the 14 differ-
ent programs.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs.
• RGB mode - Choose a desired color to stay static, or adjust and intensitys of the RGB colors to create a desired color.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation® Show Designer™.
Master-Slave Operation:
This function will allows you to link units together to run in a MasterSlave mode. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use approved DMX-512 data cables to link your units together. Remember that the Male XLR connector is the input and theFemale XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Using the Master unit, choose your desired mode or program and connect the “Slave” unit or units.
3. On the “Slave” unit(s) press the MODE button until “SLAVE” is displayed. They will now follow the “Master” unit.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 7
Event Panel System™
Operating Instructions
Programs Mode:
There are 14 programs to choose from.
Notes: Program 1 is “Static” so you can only choose from 7 different Colors and Blackout. Programs 2-12 you can adjust the
Speed of the program and the Fade Time. Programs 13-14 you
can adjust the Speed, Fade Time, and First Color and Second
Color of the Color Flow.
1. Plug the fixture in and press the MODE button. The Program Mode is after Sound Active mode in the menu. 2. Select your desired program in by pressing either the UP or DOWN buttons. There are 14 programs to choose from.
3. After you have selected your desired program, press the SETUP button to adjust the different features the program has. Please see above to understand what program features can be adjusted.
When you are adjusting a feature a small line will appear underneath the feature or next to it so that you know what you are adjusting.
FEATURES AND ADJUSTMENTS
• When “S.XX” is displayed you are adjusting the speed of the pro-
gram. Use the UP or DOWN buttons to adjust. The speed can be
adjusted from “S.01” the slowest, to “S.100” the fastest. Press the SETUP button when you are finished, to either go to the next fea-
ture adjustment or to return to the Program menu. NOTE: This
adjustment is only available with Programs 2-14.
• When “F.XX” is displayed you are adjusting the fade time of the program. Use the UP or DOWN buttons to adjust. The fade time
can be adjusted from “F.01” the slowest, to “F.100” the fastest. Press the SETUP button when you are finished, to either go to the next feature adjustment or to return to the Program menu. NOTE:
This adjustment is available with Programs 1-14.
• When “1” is displayed you are adjusting the first color of the color flow. Use the UP or DOWN buttons to adjust. Scroll through the colors to find your desired color. Press the SETUP button when you are finished, to go to the next feature adjustment. “2” will be displayed you are now adjusting the second color of the color flow. Use the UP or DOWN buttons to adjust. Scroll through the colors to find your desired color. Press the SETUP button when you are finished, to return to the Program menu. NOTE: This adjustment is
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 8
Event Panel System™
Operating Instructions
only available with Programs 13-14.
Auto Run:
1. Plug the fixture in and press the MODE button until AUTO is dis-
played. You are now in AUTO mode and the fixture will now cycle
through the built in programs.
2. Press the UP or DOWN buttons to adjust the “frequency” or speed the auto run mode.
Sound Active Mode:
In this mode the Event Panel System™ will react to sound, and chase
through the different colors. There are two sound active modes to
choose from.
1. Plug the fixture in and press the MODE button until SOUND is dis- played. The fixture will now change color via sound.
2. You can press the UP or DOWN buttons to adjust the sound sensi-
tivity level. The sensitiviey can be adjusted from “SENS.00” the
least sensitive, to “SENS.31” the most sensitive.
Event Panel System™
Operating Instructions
connections to any standard DMX controller.
3. Press the MODE button until DMX MODE: ADDR is displayed. Press the UP or DOWN buttons to select your desired address. Once you have set your desired DMX address press the SETUP button to to choose your desired DMX mode.
4. When you press the SETUP button DMX MODE: MODE should be displayed. Press the UP or DOWN buttons to select your desired DMX mode.
The Modes go as follows: DMX MODE 1 is 3 Channel mode,
DMX MODE 2 is 4 Channel mode, DMX MODE 3 is 14 Channel mode, DMX MODE 4 is 26 Channel mode, DMX MODE 5 is 2 Channel mode, DMX MODE 6 is 7 Channel mode, DMX MODE 7 is 5 Channel mode, and DMX MODE 8 is 6 Channel mode.
5. Please see pages 12-20 for DMX values and traits.
RGB Mode:
In this mode you can select either red, green, blue, or adjust the colors to make a deisred color, which will remain static. Adjust the intensity of each color to make your desired color..
1. Plug the fixture in and press the MODE button until “COLR” is dis- played.
2. Press SETUP to scroll through the colors. Press the UP or DOWN buttons to adjust the intensity of the displayed color. When you
have adjusted your desired color press SETUP to scroll to the next
color.
DMX Mode:
There are eight DMX Modes to choose from: 2 Channels, 3 Channels,
4 Channels, 5 Channels, 6 Channels, 7 Channels, 14 Channels, or
26 Channels. Operating through a DMX controller give the user the
freedom to create their own programs tailored to their own individual
needs.
1. This function will allow you to control each individual fixture’s
traits with a Elation® DMX 512 Controller.
2. To run your fixture in DMX mode, plug in the fixture via the XLR ©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 9
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 10
Event Panel System™
Battery Pack
The Event Panel comes with a portable battery pack so that you can
set up the fixture anywhere without the use of a wall outlet.
To charge the battery pack, you must first disconnect the LED
Panel from the battery. Once disconnected, connect the battery
pack to a matching power outlet using the supplied 12v DC power
supply. Turn the battery pack on to begin charging. Again, the LED
Panel must be disconneted from the battery pack when charging the
battey.
When the pack is charging the Red LED will glow, when the pack is
fully charged the Green LED will glow.
Event Panel System™
Channel
1
1 - 255
2
1 - 255
3
1 - 255
Event Panel System™
Channel
Connect the battery pack to the Event Panel via the 2-pin cable and
turn on the power to the battery pack.
1
It takes about 8 hours to fully charge the battery pack. If the battery pack is completely discharged, it will take 4-6 hours for the
first LED to glow.
Pay attention to the Battery Life Indicator on the battery pack to
keep track of the battery pack charge level.
2
- www.elationlighting.com - Event Panel System™ User Manual Page 11
Value
1 - 255
1 - 255
3
1 - 255
4
1 - 255
Connecting the Event Panel to the Battery Pack:
Connect the Event Panel to the battery pack using the included trigger pins. Line up the trigger pins with the holes and rotate the pins
unil you feel them slide easily into the holes. To lock the pins into
place apply pressure and rotate turn the pins clockwise to lock them
into place. Test the attachment by gently pulling on the Event Panel.
©Elation®
Value
©Elation®
DMX Values & Traits - 3 Channels
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
DMX Values & Traits - 4 Channels
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MASTER DIMMER
0% - 100%
- www.elationlighting.com - Event Panel System™ User Manual Page 12
Event Panel System™ DMX Values & Traits - 14 Channels
Channel
Value
1
1 - 255
2
1 - 255
3
1 - 255
4
1 - 255
5
1 - 255
6
1 - 255
7
1 - 255
8
1 - 255
9
1 - 255
10
1 - 255
11
1 - 255
12
1 - 255
13
1 - 255
14
1 - 255
Function
RED 1
0% - 100%
GREEN 1
0% - 100%
BLUE 1
0% - 100%
RED 2
0% - 100%
GREEN 2
0% - 100%
BLUE 2
0% - 100%
RED 3
0% - 100%
GREEN 3
0% - 100%
BLUE 3
0% - 100%
RED 4
0% - 100%
GREEN 4
0% - 100%
BLUE 4
0% - 100%
STROBE
SLOW - FAST
MASTER DIMMER
0% - 100%
Event Panel System™
Channel
DMX Values & Traits - 26 Channels
Value
1
1 - 255
2
1 - 255
3
1 - 255
4
1 - 255
5
1 - 255
6
1 - 255
7
1 - 255
8
1 - 255
9
1 - 255
10
1 - 255
11
1 - 255
12
1 - 255
13
1 - 255
14
1 - 255
15
1 - 255
Function
RED 1
0% - 100%
GREEN 1
0% - 100%
BLUE 1
0% - 100%
RED 2
0% - 100%
GREEN 2
0% - 100%
BLUE 2
0% - 100%
RED 3
0% - 100%
GREEN 3
0% - 100%
BLUE 3
0% - 100%
RED 4
0% - 100%
GREEN 4
0% - 100%
BLUE 4
0% - 100%
RED 5
0% - 100%
GREEN 5
0% - 100%
BLUE 5
0% - 100%
Continued on the next page
©Elation®
- www.elationlighting.com - Event Panel System™ Instruction Manual Page 13
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 14
Event Panel System™
Channel
DMX Values & Traits - 26 Channels
Value
16
1 - 255
17
1 - 255
18
1 - 255
19
1 - 255
20
1 - 255
21
1 - 255
22
1 - 255
23
1 - 255
24
1 - 255
25
1 - 255
26
1 - 255
Function
RED 6
0% - 100%
GREEN 6
0% - 100%
BLUE 6
0% - 100%
RED 7
0% - 100%
GREEN 7
0% - 100%
BLUE 7
0% - 100%
RED 8
0% - 100%
GREEN 8
0% - 100%
BLUE 8
0% - 100%
STROBE
SLOW - FAST
MASTER DIMMER
0% - 100%
Event Panel System™
Channel
Value
1
0 - 10
11 - 21
22 - 32
33 - 43
44 - 54
55 - 65
66 - 76
77 - 87
88 - 98
99 - 109
110 - 120
121 - 131
132 - 142
143 - 153
154 - 164
165 - 175
176 - 186
187 - 197
198 - 208
209 - 219
220 - 230
231 - 255
2
DMX Values & Traitss - 2 Channels
Function
MACROS/PROGRAMS
OFF
RED
YELLOW
GREEN
CYAN
BLUE
PURPLE
WHITE
SLOW DREAM
FAST DREAM
COLOR FADE
COLOR CHANGE
FLOW 1
FLOW 2
FLOW 3
FLOW 4
DOUBLE FLOW 1
DOUBLE FLOW 2
MULTI COLOR
2 COLOR FLOW 1
2 COLOR FLOW 2
SOUND ACTIVE
SPEED/SOUND SENSITIVITY CONTROL
0 - 255
SLOW - FAST
When the Channel 1 fader level is between the values of 88 and 230,
the Channel 2 fader will control the speed of the macro/program.
When the Channel 1 fader is between 231 and 255 (Sound Active) the
Channel 2 fader will control the sound sensitivity level. Channel 2 will
start at least sensitive to most sensitive.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 15
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 16
Event Panel System™
Channel
1
Value
1 - 255
2
1 - 255
3
1 - 255
4
0 - 10
11 - 21
22 - 32
33 - 43
44 - 54
55 - 65
66 - 76
77 - 87
88 - 98
99 - 109
110 - 120
121 - 131
132 - 142
143 - 153
154 - 164
165 - 175
176 - 186
187 - 197
198 - 208
209 - 219
220 - 230
231 - 255
5
6
7
DMX Values & Traitss - 7 Channels
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MACROS/PROGRAMS
OFF
RED
YELLOW
GREEN
CYAN
BLUE
PURPLE
WHITE
SLOW DREAM
FAST DREAM
COLOR FADE
COLOR CHANGE
FLOW 1
FLOW 2
FLOW 3
FLOW 4
DOUBLE FLOW 1
DOUBLE FLOW 2
MULTI COLOR
2 COLOR FLOW 1
2 COLOR FLOW 2
SOUND ACTIVE
SPEED/SOUND SENSITIVITY CONTROL*
Event Panel System™
Channel
1
1 - 255
2
1 - 255
3
1 - 255
4
1 - 255
5
0
1-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
1 - 255 SLOW/LEAST SENSITIVE - FAST/MAX SENSITIVE
PROGRAM SPEED
1 - 255
SLOW - FAST
MASTER DIMMER
1 - 255
0% - 100%
*When the Channel 4 fader level is between the values of 88 and 230, the Channel 5 fader will
control the speed of the macro/program. When the Channel 4 fader is between 231 and 255
(Sound Active) the Channel 5 fader will control the sound sensitivity level.
©Elation® - www.elationlighting.com - Event Panel System™ User Manual Page 17
Value
©Elation®
DMX Values & Traits - 5 Channels
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MASTER DIMMER
0% - 100%
COLOR MACROS
OFF
BASTARD AMBER
MEDIUM AMBER
PALE AMBER GOLD
GALLO GOLD
GOLDEN AMBER
LIGHT RED
MEDIUM RED
MEDIUM PINK
BROADWAY PINK
FOLLIES PINK
LIGHT LAVENDER
SPECIAL LAVENDER
LAVENDER
INDIGO
HEMSLEY BLUE
TIPTON BLUE
LIGHT STEEL BLUE
LIGHT SKY BLUE
SKY BLUE
BRILLIANT BLUE
LIGHT GREEN BLUE
BRIGHT BLUE
PRIMARY BLUE
CONGO BLUE
- www.elationlighting.com - Event Panel System™ User Manual Page 18
Event Panel System™
Channel
Value
5
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
DMX Values & Traits - 5 Channels
Function
COLOR MACROS CONT.
PALE YELLOW GREEN
MOSS GREEN
PRIMARY GREEN
DOUBLE CTB
FULL CTB
HALF CTB
DARK BLUE
WHITE
Event Panel System™
Channel
1
Value
1 - 255
2
1 - 255
3
1 - 255
4
0 - 10
11 - 21
22 - 32
33 - 43
44 - 54
55 - 65
66 - 76
77 - 87
88 - 98
99 - 109
110 - 120
121 - 131
132 - 142
143 - 153
154 - 164
165 - 175
176 - 186
187 - 197
198 - 208
209 - 219
220 - 230
5
1 - 255
6
1 - 255
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 19
©Elation®
DMX Values & Traits - 6 Channels
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MACROS/PROGRAMS
OFF
RED
YELLOW
GREEN
CYAN
BLUE
PURPLE
WHITE
SLOW DREAM
FAST DREAM
COLOR FADE
COLOR CHANGE
FLOW 1
FLOW 2
FLOW 3
FLOW 4
DOUBLE FLOW 1
DOUBLE FLOW 2
MULTI COLOR
2 COLOR FLOW 1
2 COLOR FLOW
PROGRAM SPEED
SLOW - FAST
MASTER DIMMER
0% - 100%
- www.elationlighting.com - Event Panel System™ User Manual Page 20
Event Panel System™
Fuse Replacement
First unplug the power. The fuse holder is located next to the power
cord. Using a phillips screw driver unscrew the fuse holder. Remove
the bad fuse and replace with a new one.
Event Panel System™
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Event Panel System™
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
2. Some DMX modes have a dimmer channel. Make sure the dim-
mer channel is not at 0%.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Check the sound sensitivity level. See Sound Active mode.
If problems are not resolved; Contact Elation® for service.
1-866-245-6726
Event Panel System™
2-YEAR LIMITED WARRANTY
Warranty
A. Elation Professionals® hereby warrants, to the original purchaser, Elation Professionals® products to be free of manufacturing defects in material and workmanship
for a period of two years (730 days) from the date of purchase. This warranty shall be
valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professionals® factory.
All shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, Elation Professionals® will
pay return shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product,
Elation Professionals® shall have no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professionals® concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced
by anyone other than the Elation Professionals® factory unless prior written authorization was issued to purchaser by Elation Professionals®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance,
cleaning or periodic check-up. During the period specified above, Elation Professionals® will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The
sole responsibility of Elation Professionals® under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion
of Elation Professionals®. All products covered by this warranty were manufactured
after January 1, 1990, and bear identifying marks to that effect.
E. Elation Professionals® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in
any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited
by applicable law, all implied warranties made by Elation Professionals® in connection with this product, including warranties of merchantability or fitness, are limited in
duration to the warranty period set forth above. And no warranties, whether expressed
or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professionals® be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 21
G. This warranty is the only written warranty applicable to Elation Professionals®
Products and supersedes all prior warranties and written descriptions of warranty
terms and conditions heretofore published.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 22
Event Panel System™
Model: Event Panel System™
Specifications
SPECIFICATIONS:
Lamps:
Beam Angle:
Output Distance:
Working Position: Voltage: Power Consumption:
Fuse:
Weight: Dimensions:
Event Panel:
Battery Pack:
Colors:
DMX Channels:
Warranty:
288 LEDs: 48 Red, 120 Green, and
120 Blue
40 Degrees
45~50m
Any safe working position
90 ~ 240V (Event Panel)
12v DC (Battery Pack)
36W
1 Amp
7.7lbs./ 3.5Kgs. (Event Panel)
19.5lbs./ 8.84Kgs. (Battery Pack)
16.7” (L) x 10.3” (W) x 3.2” (H)
425 (L) x 263 (W) x 82 (H) mm
11.7” (L) x 11.6” (W) x 4.6” (H)
298 (L) x 295 (W) x 118 (H) mm
RGB Color Mixing
2, 3, 4, 5, 6, 7, 14, & 26
2 Year (730 days)
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©Elation®
- www.elationlighting.com - Event Panel System™ User Manual Page 23
©Elation Professional®
A Division of the AmericanDJ® Group of Companies
World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-3322 Fax: 323-832-9142
Web: www.elationlighting.com E-mail: info@elationlighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising