WT-204 GSM Wireless Terminal (4 Ways)

WT-204 GSM Wireless Terminal (4 Ways)
WT-204 GSM Wireless Terminal (4 Ways)
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
Features
•
•
•
•
•
•
•
•
•
•
•
Adopts advanced microprocessor controlling circuit, runs steadily and its functions are all complete
Enhanced high gains external antenna
Be suitable to GSM900/1800MHz
Locking terminal, locking SIM card and locking network can be set up flexibly.
Diversiform function on calling out or being called in can be set according to your need
Display incoming calls
Barred telephone numbers can be set flexibly
Prefixal code can be set according to user’s requirement
Can be connected to charging device
Can be connected to PBX
With the function of network management, the parameters can be set through network manager
The Frontal Appearance of WT-204
The instructions to the frontal appearance of WT-204
Indicators and knobs (from up to down)
•
•
•
•
•
Status indicator—flashing once in one second indicates that the terminal has been on GSM network
Used indicator —Staying lit during calls and during parameters’ setting
Warn indicator—Staying lit for less than 10 seconds indicates that the terminal is dealing with SMS. If
it stays lit for more than 10 seconds, there is some trouble with the terminal.
Reset knob — press this knob, its corresponding board will reset.
Power switch—push to “On” or “OFF” side to turn on or shut off the terminal.
The Rear Appearance of WT-204
Instructions to the rear appearance of WT-204
•
•
•
Power port—connect to power adapter
Phone port—connect to a phone
Antenna port—connect to antenna
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-2-
Installing the SIM Card
Proceed as follows:
a.
b.
c.
d.
Slide back the SIM door and lift it up
Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with
the clipped corner of the SIM holder
Close the SIM door
Slide the SIM door to lock the SIM card in place
Setting up the Terminal
The Condition for Installation
The terminal asks for 220V AV power supply. It must be installed in the area where the GSM network can
cover. The strength of the signal can affect the quality of voice direct.
The Installation for Connect to Ordinary Telephone
1.
2.
3.
4.
Screw off the screws that are on the back of the terminal and pull out the corresponding circuit board.
Install SIM card for every circuit board and install the circuit board in place, and then tighten the
screws.
Install antenna. In order to ensure the quality of voice, antenna must be put beyond 1.5m from the
telephone and terminal.
One end of the telephone line connects to the “Phone” port of the terminal, the other end connects to
telephone.
“Power” port connects to power adapter that is connected to220V AC power supply. About 15—45
seconds later (the time is subject to local wireless network), the terminal will work in gear.
The sketch for connecting to ordinary telephone: each circuit board can be connected to one telephone
Draw your attention: Because there are many types of ordinary telephone and their electric parameters are
different .In order to avoid mutual disturbance between telephone and terminal and affect voice
quality .The distance between telephone and terminal is 1.5m at least.
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-3-
The installation connecting to charging device
If the users demand to register cost during calls, charging device can be connected between terminal and
ordinary telephone. Charging device register cost according to the anti-polarity signal that is provided by
terminal.
1.
The sketch map of connecting multi-route charging device
2.
The sketch map of connecting to computer charging system
The installation for connecting to PBX
If users want to connect small PBX to this terminal, connect terminal’s “Phone port” to the PBX.
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-4-
Making Calls and Answer Incoming Calls
Making Calls
1.
2.
3.
4.
5.
6.
Lift the handset or press “hand-free” key, you will hear dialing tone, then you can dial the telephone
numbers you want to call.
Dialing: dialing the telephone numbers you want to call
On completion of dialed digits, you can press “#” to transmit the called telephone numbers. If you
don't dial any key for continual 6 seconds during the dialing, terminal transmits called telephone
numbers automatically.
During calls, if the telephone numbers is not free ones, the terminal sends out anti-polarity signal (the
signal is used to register cost by charging device).
If the calling party or called party hangs up, the terminal stops sending out anti-polarity signal.
If users dial barred numbers telephone will give out the sound of three-time toot to ask the user to hang
up.
Answering Incoming Calls
When some calls are coming in, if the connected telephone has the function of displaying incoming calls,
the telephone rings and displays the incoming telephone numbers. Now users can lift the handset or press
“hand-free” to answer it.
Turn on or turn off the terminal
Put power switch to “OFF” side to turn off the terminal and put the power switch to “ON” side to turn on
the terminal.
The Information about Signal Quality, Malfunction and Software Version
If the connected phone has the function of displaying incoming calls, the telephone rings after the terminal
is login onto GSM network successfully and a code of 8 digits will be displayed .The code indicates the
information about signal quality, malfunctions and software version as follows:
The first two digits indicate the signal quality; it ranges from “00” to “31”. Stronger the signal is, bigger the
digits is. If it is less than 10, the quality of voice will be poor.
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-5-
The third and the forth digit is the code of malfunction:
“00”: good
“11”: failed in login onto GSM network
“22” or “33”: PIN error (PIN code isn’t 1234 or PIN isn’t disabled),
“44”: lock card error,
“55”: lock terminal error
“77”: lock network error, “99”: read card error
The later four digits is the code of software version: for example 4060 indicates the software version code
is 4.06.
If the telephone displays “11”or “22” or “33” or “44” or “77” or “99” or the telephone can’t work in gear,
please contact service provider.
Inquire Signal Quality and Software Version
Lift the handset and then dial “***9#”. Hang up as soon as you hear the busy tone. The telephone rings and
displays a code of 8 digits. The code indicates the information of signal quality and software version as
follows:
The first two digits indicate signal quality. It ranges “00” to “31”. Stronger the signal is, bigger the digits is.
If it is less than 10, the quality of voice will be poor.
The third and the forth digits are both standby.
The later four digits is the code of software version: for example 4060 indicates the software version code
is 4.06.
Adjusting the Volume of Voice
Lift the handset or press “hand-free” key.
Dial “*33XY#” and then hang up when hear the sound of toot.
X and Y both belong to the digits that range from 1 to 5. X indicates microphone volume and Y indicates
speaker volume. Level 1 is the lowest volume and level 5 is the highest.
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-6-
The Instructions for Terminal’s Running Status
1.
2.
3.
4.
5.
6.
7.
8.
The instruction for initializing terminal
When Power indicator is lit, the terminal begins to initialize. If Status indicator and Used indicator are
flashing simultaneously, the terminal is searching for network. About 15 ~ 45 seconds later, the
telephone rings that indicates the process of initialization terminal finishes. If Warn indicator stays lit,
initialization is unsuccessful. On this condition user can set parameters for the terminal but the terminal
can’t be used to make any calls. If users dial telephone numbers, the Warn indicator will flash and the
telephone will give out the sound of three -time toot to ask the user to hang up.
While users dialed barred numbers or other error numbers, the telephone gives out the sound of threetime toot to indicate that user should hang up and redial.
While you are lifting the handset and don’t dial any key for continuous 15 seconds or nobody answer
the dialed telephone for 90 seconds after the called telephone has ringed, the telephone will give out
the sound of three-time toot to indicate the user to hang up. If the user doesn’t hang up for a long time,
all indicating sound will stop after 1 minute.
While calls coming in, Used indicator flashes. IF user answers the call, the Used indicator stays lit until
the call is hung up.
When user is lifting the handset, Used indicator stays lit until user hangs up.
When the terminal receives SMS, Warn indicator and Used indicator both stay lit that indicates that the
terminal is dealing with SMS.
If Warn indicator stays flashing and the telephone continuously gives out the sound of three-time toot,
which indicates that the terminal is on the warning status. Please hang up.
Technical Specification
1.
2.
3.
4.
5.
6.
7.
Working condition
Environment temperature: 0~+50℃
Relative humidity: 10%~95%
Air pressure: 86~106kpa
Environment yawp: ≤60Db (A)
Working frequency: GSM900/GSM1800MHz
Stability of frequency: better than 2.5PPM
Signal sensitivity: -103DbM
Transmit power: <2w
Power Supply: 220v±15% AC
The maximal distance between terminal and telephone: 100M
Maintenance and storage
1.
2.
3.
The terminal should be saved in the desiccant place.
If three are some matters with the terminal, please send it to the appointed repair center. (The damages
that are caused by error operation are beyond the scope of our free maintenance). Don't take apart the
terminal by yourself without our agreement
The packed terminal should be put in dry and ventilated place. The number of lays of piled terminal
can’t more than 10. The condition of the storehouse is listed as follows:
Temperature: -10 to +45℃ Relative humidity: ≤95%
You should ensure that there is no corrosive gas in the storehouse too.
Familiar Trouble and Troubleshooting
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-7-
Phenomena
Trouble
Warn indicator stay
bright for long time
Failed in login onto
GSM network
Power indicator isn’t
bright
Having not connect
to power supply
Only free numbers
can be called out
Can’t hear of sound
during calls
The residual money
on SIM card is too
less
The malfunction on
the telephone
Poor voice quality
during calls or there
is echo during calls
The voice volume is
too high or the
signal of GSM
network is too weak.
No ringing sound
The malfunction on
the telephone
Incoming calls can’t
be answered
The connected
telephone does not
match the terminal or
forbidding answering
incoming calls are set
Trouble Shooting
1. The signal is too weak Please move the terminal to the
place where signal is stronger.
2. Check whether antenna is connected well.
3. SIM card is locked. Please contact the service provider.
1. Check whether the adapter is connected well.
2. There is some trouble with the power adapter
Please contact the terminal provider.
Add money to the SIM card
Change the connected telephone with a good one
1. Adjust the voice volume to be lower.
2. The local signal is too weak. Move the terminal to the
place where signal is stronger.
3. Make the antenna is longer from the telephone
4. The voice quality of the connected telephone isn’t good.
Change the connected telephone
5. Trouble on the network.
1. Malfunction on connected telephone
2. Malfunction on terminal. Please contact the terminal
provider.
1. Chang the connected telephone with a suitable one.
2. Forbidding answering incoming calls is set.
Please contact the service provider.
WITURA CORPORATION SDN BHD
Office Address: 18-8-C, Gurney Tower, Persiaran Gurney, 10250 Penang, Malaysia. Tel: 604 - 228 9053
Fax: 604 – 228 9054
URL: http:// www.witura.com
Email: [email protected]
-8-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement