User manual | Oscilloscopes

www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
Test & Measurement
Oscilloscopes - contents
91 Bench Power Supplies
2172
92 Lab Equipment,
Environmental Monitoring &
Calibration
2182
93 Network, Cable & Electrical
Testing
2239
94 Inspection & Mechanical
Measurement
2283
95 Multimeters
2310
Digital Storage Oscilloscopes
2340
2340
Digital Phosphor Oscilloscopes
2342
PC Based Oscilloscopes
2343
Combined Analogue & Digital
Storage Oscilloscopes
2344
Analogue Oscilloscopes
2344
Handheld Oscilloscopes
2345
Spectrum Analysers
2348
Circuit Analysers
2348
Oscilloscope Probes
2348
97 Logic Analysers & Signal
Generation
2353
98 Test Leads & Accessories
2361
96
Visit our website for additional price information and exciting promotions
2337
www.nguyenxuong.com
Go where scopes could
never go before
New
The first four-channel scope built
for CAT IV industrial environments.
t CAT III 1000V/CAT IV 600 V safety rated so
you can take on three-phase applications like
industrial motors, variable speed drives, UPS and
inverters
t Test input, output and control signals
simultaneously
t High-speed, high-resolution: up to 2.5 GS/s with
up to 400 ps resolution
t New features you’ve been asking for like USB
connectivity and advanced battery technology
that lasts all day long.
Learn more about Fluke’s complete line of rugged, high-performance
ScopeMeter® Portable Oscilloscopes at RS Components.
©2012 Fluke Corporation. Specifications are subject to change without notice.
www.nguyenxuong.com
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
HCTEK4321 Transit Case
ISO-TECH
ISO-TECH IDS8000 Series
High performance colour TFT LCD
display digital storage oscilloscopes.
Fast 1GSample/sec single shot sample
rate for capturing fast signals and 25K
maximum record length fulfils the
requirement for waveform capture of
multiple and complex wavefroms. The
25GS/s repetitive sampling mode maintains an effective high sample rate for fast timebase settings for
repetitive signals . The front panel USB port provides printer & PC communications and enables
unlimited waveform & panel setup storage to USB memory sticks.
1GS/s Max real time sample rate (single channel)
25GS/s max equivalent time sample rate
2 or 4 channel models
25K Max display memory length (single channel)
8 x 12 graticule 5.6 inch colour TFT display with 234 x 320 VGA resolution
AUTOSET button
On line HELP menu
24 automatic measurement functions
FFT (frequency spectrum) display mode
XY mode
15 sets of SAVE/RECALL setup settings
8 sets of Waveform + template storage
Trigger capability includes TV, Edge, pulse Width, Time delay & event delay (2 Channel models)
Acqusition Modes: Sample, Peak Detect, Average, Accumulate
USB 2.0 port (host / device) front panel mounted provides Plug-and-play PC connectivity, supports
USB Printer and USB Flash memory devices
DB 9-pin male DTE RS-232 interface (rear panel)
GO/NO GO output (open collector)
Supplied with: Mains lead, PC control software on CD-ROM, user manuals, x1/x10 fixed probes
Vertical
Vertical Resolution
Accuracy
Sensitivity
Input Coupling
Input Impedance
Polarity
8 Bits
± (3% x |Readout| 0.05 div x Volts/div)
2mV/div 5V/div (1-2-5 increments)
AC, DC & Ground
1MΩ ±2% , 16pF
Normal & Invert
Maximum Input
300V (DC AC peak), CATII
Accuracy
Pre-trigger
Post-trigger
X-Y Mode
Phase shift
Signal Acquisition
Single Shot
Bandwidth
Acquisition Mode
Waveform Signal
Process
Bandwidth Limit
Trigger
Sources
+ , -, x ,̧ , FFT
Peak Detection
±0.01%
20 div maximum
1000 div
±3° at 100kHz
100MHz
Sample, Peak Detect, Average,
Accumulate
10ns
Average
2, 4, 8, 16, 32, 64, 128, 256
Cursors & Measurement
CH1 , CH2 , Line , EXT(2CH Only) /
Voltage
V pp V amp V avg V rms Vhi Vlo V max
(CH3,CH4)
Measurement
V min, Rise Preshoot/ Overshoot, Fall
Preshoot/Overshoot
Coupling
AC, DC, LFrej, HFrej, Noise rej
Time Measurement Freq, Period, Rise Time, Fall Time,
Positive Width, Negative Width, Duty
Cycle
Ext Trigger(2 channel models only)
Delay Measurement Eight different delay measurement
Range
±15V; Max Input 300V (DC AC peak) , Cursors
Voltage difference between cursors
CATII
Measurement
(ΔV)Time difference between cursors
(ΔT)
Sensitivity
DC - 30MHz : 50mV ; 30M - 60/100/
Auto Frequency
6 digits Accuracy : ±2%: Signal Source:
200MHz : 100mV
Counter
All available trigger source except the
Video trigger mode
Input Impedance 1MΩ ±2% , 16pF
Real Time Clock
Display yy/mm/dd hh/mm/ss; provides
Date/Time for saved data
Horizontal
Printer Compatibility HP Deskjet 970CXI, LaserJet 1010 ,
(USB)
LaserJet 1015, LaserJet 1300
Range
1ns/div 10s/div (1-2-5 increments);
Epson Stylus C20UX, Epson Stylus C65,
Epson AL-C8600
ROLL : 250ms/div ∼ 10s/div
Modes
MAIN, WINDOW, WINDOW ZOOM, Dimentions &
254D 142H 310W(mm), Approx. 4.3kg
ROLL, X-Y
Weight
Description
Bandwidth (MHz)
Timebase Range
Channels
Stock no.
IDS8062
60
5.8 ns
2
619-5895
IDS8102
100
3.5 ns
2
619-5918
IDS8104
100
3.5 ns
4
619-5924
IDS8202
200
1.75 ns
2
619-5930
IDS8062
IDS8102
IDS8104
IDS8202
Stock no.
S619-5895
S619-5918
a619-5924
a619-5930
Price per
unit
unit
unit
unit
OM
S$
1+
1+
1+
1+
1250·00
1610·00
2540·00
2170·00
S$
S$
613-1510
697-8791
Accessories
2340
Price per
OM
S$
1+
1+
4840·00
2580·00
OM = Order Multiple a New product to range
1+
1460·00
S$
S$
S$
S$
Stock no.
697-8791
697-8794
697-8782
Price per
OM
S$
1+
870·00
unit
The TEK-DPG Deskew Pulse Generator is a signal-generating
accessory for Tektronix instruments that feature the TekVPIᓽ
interface, including DPO3000 series and DPO/MSO4000 series
oscilloscopes. Applications include power supply design and
measurements requiring accurate timing measurements
between channels.
Supplied with: user manual
Easy-to-use plug-on accessory for oscilloscopes with TekVPI
interface
Generated signals enable precise deskew between current
and voltage probes in power measurement applications
LED status indicator for quick identification of generator state
Multiple output signals enable use with variety of
oscilloscopes and probes
Output can be turned off to reduce power consumption when not in use
Easy access to oscilloscope menu display to control settings from the oscilloscope front panel
Type
For Use With
Pulse Generator
TEK-DPG
Stock no.
697-8823
S$
Price per
unit
OM
S$
1+
1510·00
S$
S$
TDS1000x & TDS2000x Series
General purpose digital oscilloscopes for digital design and debug, education and training,
manufacturing test and quality control, service and repair,Full sample rate and full record length on all
channels for accurate acquisition, all the time,Highly portable, lightweight and compact form factor
frees up valuable desk space ,Convenient removable data storage via front panel USB flash drive port
,Plug-and-play PC connectivity via back panel USB device port,OpenChoiceᓽ and NI SignalExpress PC
software are supplied for easy documentation and analysis of results,Easy user interface with familiar,
analogue-style controls, multipurpose knob, context-sensitive HELP and AUTORANGE
function,AUTOSET button to detect and display the waveform, provides different views and displays
up to four automatic measurements ,Pulse width trigger speeds digital troubleshooting ,External
trigger input ,Probe Check Wizard to quickly verify probes are calibrated and operating properly,Lineselectable video trigger permits triggering on a specific line of video to improve measurement
productivity ,Trigger signal frequency readout allows the measurement of a signal’s frequency without
the need for an output channel ,11 automatic measurements for fast, error-free measurements, ideal
for repetitive tests ,Fast Fourier Transform (FFT) (spectrum) display to analyse, characterise and
troubleshoot circuits by viewing frequency and signal strength ,Directly print screen images to any
PictBridge compatible printer,Integrated security loop for theft protection
Vertical resolution/
accuracy
unit
unit
Stock no.
RMD2000
Vertical sensitivity
606-0698
628-7534
Rackmount
DPO/MSO2000
Rackmount Kit
RMD2000
RMD3000
RM4000
Manu. Part No.
Accessories for TDS 1000 series
Stock no.
S$
unit
Type
For Use With
Oscilloscope Families
DPO2000, MSO2000
DPO3000, MSO3000
DPO4000, MSO4000
Trigger modes
Glitch Capture
TCP303 150A 15 MHz
TCP305 50A 50 MHz
OM
These kits for Tektronix DPO and MSO family oscilloscopes
provide access to rear panel connections and maximise the
use of space in rackmount applications.
TDS 1000 & 2000 Series
Description
Price per
Rackmount Kits
Record Length
Trigger type
TCP303 and TCP 305 current probes suitable for
measuring AC or DC
96
Stock no.
TekVPI Deskew Pulse Generator
Signal Source TEK-DPG
20MHz ( -3dB)
Description
HCTEK4321 rugged transit case provides travel and storage
protection for TDS3000, TPS2000, TDS2000, TDS1000, and
TDS200 series oscilloscopes. The case protects instruments
from shock, vibration, and moisture, and provides room for
accessories, such as probes, adapters, and manuals. Includes
an air pressure equalization control valve for use during air
transport and security rings for use with locks (locks not
supplied).
2.5K points
Edge (rise, fall), video, pulse
width, glitch
Auto, normal, single
12ns
Timebase range
Timebase accuracy
5ns to 50 sec/div
50ppm
Input impedance
Acquistion modes
2mv to 5v/div with calibrated
fine adjustment
8-bits / ±3%
Dimensions/weight
1MΩ in parallel with 20pF
Peak detect, sample, average,
single
W. 323.8 H.151.4 d.124.5 Wt 2kg
www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
Record Length
Automatic Waveform
Measurements
Vertical Resolution
Vertical Sensitivity
Vertical Accuracy
Vertical Zoom
Max Input Voltage (1 MΩ)
Input Voltage Rating
TDS1000B Mono
TDS1000B Series with
Monochrome Display, 1GS/s
Sample Rate & USB ports
Monochrome LCD display
Supplied with: IEC mains lead, manual and 2 x P2200 x1/
x10 passive probes
Sample Rate
Channels
Timebase Range
Description Bandwidth (MHz)
TDS1001B
TDS1002B
TDS1002B
TDS1012B
TDS1012B
40
60
60
100
100
1 GS/ s
2
5ns - 50s/div
Stock no.
S617-0048
S617-0054
a713-9798
S617-0060
a713-9792
Price per OM
unit
unit
unit
unit
unit
1+
1+
1+
1+
1+
S$
S$
S$
1570·00
1950·00
2150·00
2330·00
2480·00
2.5kpoint record length on all
channels
Advanced triggers including Pulse
Width trigger and line-selectable
Video trigger
16 automated measurements, and
FFT analysis for simplified waveform
analysis
Built-in waveform limit testing
Automated, extended data-logging
feature
Autoset and signal auto-ranging
USB 2.0 Host Port on front panel for data storage, printing, and connecting a USB keyboard
USB 2.0 Device Port on rear panel for connection to PC or direct printing to a PictBridgeᓼcompatible printer
Built-in context-sensitive Help
Probe check Wizard
Multiple-language user interface
5.7in. (144 mm) Active TFT colour display
Small footprint and lightweight: 4.9in. (124mm) deep and 4.4lb. (2kg)
Supplied with: National Instrument’s LabVIEW SignalExpressᓽ TE Limited Edition and Tektronix
OpenChoiceᓼ software.
Description
TDS2001C
TDS2002C
70MHz 4-channel TDS2004C
UK
TDS2012C UK
TDS2014C UK
TDS2022C UK
TDS2024C UK
Stock no.
Max Input Voltage (1 MΩ)
Position Range
Bandwidth Limit
Linear Dynamic Range
Time Base Accuracy
Input Impedance
Input Coupling
Horizontal Zoom
Dimensions
Manu. Part No.
TDS2000C Colour
Price
per
OM
S$
Sa715-8682
S715-8686
S715-8695
unit
unit
unit
1+
1+
1+
1640·00
1790·00
3010·00
S715-8698
S715-8692
S715-8702
S715-8705
unit
unit
unit
unit
1+
1+
1+
1+
2400·00
3570·00
3410·00
3770·00
S$
S$
TPS2000 Series Digital Storage
Oscilloscopes
TPS2012, TPS2014 & TPS2024
Isolated Channel, Battery Powered
The TPS2000 series is capable of making a broad range of
measurements from three-phase power and multi-channel
floating and grounded measurements on up to four channels
simultaneously to debugging control circuits. The series
features up to 4 IsolatedChanneltm inputs and external trigger
input for taking safe floating and differential measurements
as well as maintaining the safety of the test equipment and
the systems under test.With up to 8 hours continuous battery life in a highly mobile package the
TPS2000 series is ideally suited for use on the bench, in the power lab, or in the field for industrial
power design and test, equipment installation and maintenance and automotive design and test
applications.
Traditional oscilloscope user interface with dedicated knobs per channel and colour LCD display
2 or 4 fully isolated and floating channels (600V max w.r.t Earth ground), including external trigger
Provision for two battery slots to provide up to 8 hours of continuous battery operation (supplied
with 1 battery as standard)
Batteries can be "hot swapped" and charged on optional TPS2CHG fast charger to provide
continuous battery operation
Power application package available separately, provides a range of power measurements
including instantaneous power waveform analysis, waveform analysis, harmonics analysis,
switching loss, phase angles, and dv/dt and di/dt cursors
FFT (spectrum) display mode standard on all models
Advanced triggers, including pulse width trigger and line-selectable video trigger
Autoset menu with waveform selection
Autorange to adjust waveforms on the oscilloscope screen and change test points without resetting
the oscilloscope
Waveform and setup memories simplify setup and operation
Zoom feature to see the details of a waveform
Backlit menu buttons and display brightness control
11 automatic measurements and built-in, context-sensitive help simplify operation
RS-232 serial port, printer parallel port & integrated CompactFlashᓼ mass storage as standard on
all models
TDSPCS1OpenChoiceTM software; A collection of programs that enable fast and easy
communication between MS Windows PCs and TPS2000 Series oscilloscopes
For full range see the RS website
Note: Bandwidth is 20 MHz at 2 mV/div, all models. Bandwidth is 200MHz typical at 5 mV/div, 200MHz
models only.
Supplied with: P2220 200 MHz, 1X/10X switchable passive probe (one per channel), TPS2BAT Li-ION
battery, TDSPCS1 OpenChoice software, instruction manuals, ac power adaptor/trickle charger with
mains lead.
2.5 K points
Period, Frequency, +Width, -Width, Rise time, Fall time, Max, Min, Peak-toPeak, Mean, Cycle RMS.
8-bits (normal or with averaging)
2 mV to 5 V/div
±3%
Vertically expand or compress a live or stopped waveform
Float voltage to 1000 VRMS CAT II with P5120 high-voltage probe
Input BNC centre connector 300V CAT II to BNC shell (common) Input, BNC
shell 600V CAT II to Earth
1000 VRMS CAT II to Earth with P5120 high-voltage probe
2 mV to 200 mV/div ±2 V; >200 mV to 5 V/div ±50 V
20 MHz
±5 div
50 ppm
1 MΩ ±2 % in parallel with 20 pF
AC, DC, GND
Horizontally expand or compress a live or stopped waveform
W 336, H 161, D130 Wt 2.7 kg (excl battery)
TPS2024B
Stock no.
S734-5004
Price per
unit
OM
S$
1+
6480·00
S$
S$
S$
S$
TPS2000 Accessories
Description
TPS2PWR1 power measurement
module
Tektronix Wavestar software
TPS2BAT rechargeable Li-ion
battery
TPS2CHG fast battery charger
P2220 probe 200MHz switchable
AC2100 soft carry case
A621 1000Amp AC probe
A622 100Amp AC/DC probe
Stock no.
Price
per
OM
S$
481-0873
unit
1+
1110·00
313-1422
481-0867
unit
unit
1+
1+
887·00
535·00
481-1084
481-0823
481-0845
851-218
851-224
unit
unit
unit
unit
unit
1+
1+
1+
1+
1+
931·00
219·00
239·00
1100·00
1120·00
TDS3000C Digital Phosphor Oscilloscopes
TDS3000C Series
TDS3000C Series features simple navigation and
dedicated front panel controls for speed and ease of use.
OpenChoiceᓼ PC Communication Software enables
screen images and waveform data to be pulled simply
into a stand-alone desktop application or directly into
Microsoft Word and Excel. To complement OpenChoice,
National Instruments LabVIEW SignalExpressᓽ Tektronix
Edition Software provides extended capabilities including
advanced analysis, data logging, remote instrument
control and live waveform analysis. For those who prefer
not to use a PC for analysis, the TDS3000C Series comes
standard with 25 automatic measurements, waveform add, subtract, divide and multiply math
functions and Fast Fourier Transform (FFT). This enables use of the full acquisition record length or
isolation of a specific occurrence within an acquisition.
Sample rates up to 5GS/s real-time on all channels
10k standard record length on all channels
3600wfms/s continuous waveform capture rate
Suite of advanced triggers
Front panel USB host port for easy storage and transfer of measurement data
25 automatic measurements
Fast Fourier Transform (FFT) standard
Multiple language user interface
WaveAlertᓼ automatic waveform anomaly detection
TekProbeᓼ interface supports active, differential and current probes for automatic scaling and units
Compact design 375mm (14.8in) wide x 176mm (6.9in) high x 149mm (5.9in) deep frees up benchtop space
Lightweight design (3.2kg/7lb without optional battery) together with robust handle for portability
Optional internal battery operation (TDS3BATC rechargeable lithium ion battery pack - not
supplied) provides up to 3 hours without line power
Application modules: advanced analysis; limit testing; telecommunications mask testing; extended
video; 601 serial digital video
Applications: digital design and debug; video installation and service; power supply design;
education and training; telecommunications mask testing; manufacturing test; general bench
testing
Supplied with: P6139A 10x passive probe (one per channel); UK and Euro mains cable; accessory
tray; protective front cover; OpenChoiceᓼ PC Communication Software; NI LabVIEW SignalExpressᓽ
Tektronix Edition LE interactive measurement environment optimized for TDS3000C series;
documentation CD; multilingual manual
External Trigger Input
Record Length
Vertical Resolution
Vertical Sensitivity, 1 MΩ
All models
10 k points
9 bits
1 mV/div → 10 V/div
Visit our website for additional price information and exciting promotions
96
2341
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
Vertical Sensitivity, 50 Ω
Input Coupling
Input Impedance
DC Gain Accuracy
Maximum Input Voltage, 1 MΩ
Maximum Input Voltage, 50 Ω
Position Range
Time Base Accuracy
Manu. Part Bandwidth Sample Rate
No.
(MHz)
(G s/s)
TDS3012C
100
1.2
TDS3014C
100
1.2
TDS3032C
300
2.5
TDS3034C
300
2.5
TDS3052C
500
5
TDS3054C
500
5
Description
1 mV/div → 1 V/div
AC, DC, GND
1 MΩ in parallel with 13 pF or 50 Ω
±2 %
150 VRMS with peaks at ≤ 400 V
5 VRMS with peaks at ≤ 30 V
±5 div
±20 ppm over any 1 ms time interval
Number of Timebase Range Rise Time (ns)
Channels
2
4 ns - 10 s
3.5
4
4 ns - 10 s
3.5
2
2 ns - 10 s
1.2
4
2 ns - 10 s
1.2
2
1 ns - 10 s
0.7
4
1 ns - 10 s
0.7
Stock no.
Price per
S463-004
S462-988
S462-984
S462-978
S462-994
S462-990
TDS3012C 100MHz 2-ch
TDS3014C 100MHz, 4-ch
TDS3032C 300MHz, 2-ch
TDS3034C 300MHz, 4-ch
TDS3052B 500MHz, 2-ch
TDS3054C 500MHz, 4-ch
OM
S$
1+
1+
1+
1+
1+
1+
8250·00
9820·00
11900·00
14100·00
17100·00
20300·00
unit
unit
unit
unit
unit
unit
S$
TDS3GV Communication Module
Stock no.
463-004
462-988
462-984
462-978
462-994
462-990
S$
GPIB (IEEE -488.2) programmability: Full talk/listen modes; Control of
all modes, settings and measurements
VGA: Monitor output for direct display on large VGA-equipped
monitors. DB-15 female connector, 31.6kHz sync rate, EIA RS-343A
compliant
RS-232-C interface programmability: Full talk/listen modes; Control of
all modes, settings and measurements. Baud Rate up to 38,4000. DB-9
male connector
Use with Wavestarᓽ for Oscilloscopes (WSTRO) for easy data
manipulation, documentation and data logging
Compatible with TDS3000 & TDS3000B series oscilloscopes
Note: Illustration is for reference purposes only.
Stock no.
413-6989
Price per
unit
OM
S$
1+
1290·00
S$
S$
S$
S$
GPIB to USB Adaptor
The TEK-USB-488 Adapter enables communication between a
GPIB bus controller, and the USB port of a USBTMC-USB488
compliant Tektronix instrument
Enables GPIB control of Tektronix instruments through the USB
port of Tektronix instruments
Compliant with USBTMC-USB488 standards
GPIB primary address is assignable through the host Tektronix
instrument
Powered by USB Host or optional external power supply
LED Indicators provide power, adapter status, and USB status
Supplied with: Adapter, two USB cables, user manual
TDS3000B: AC3000; P3010; P6139A
TDS3000B: AC3000; P3010;
P6139A
Stock no.
113-143
Products for use with the discontinued Tektronix TDS3000B
series of digital phosphor oscilloscope
Price per
unit
OM
S$
1+
1330·00
Mixed Signal Oscilloscopes
MSO2000 Series
Description
Stock no.
AC3000 soft case
349-8208
Price per
OM
S$
1+
459·00
unit
S$
S$
TDS3000B/C Series Accessories
Application Modules
TDS3AAM Advanced Application Module
Advanced analysis capability by mathematical processing of
live waveforms using a powerful maths equation editor
Area and Cycle Area measurements, differentiation and
integration functions, measurement averaging and
measurement statistics
Four selectable FFT window types (Rectangular, Hamming,
Hanning & Blackman-Harris)
TDS3LIM Limit Test Module
Fast, accurate go/no-go verification that tested circuits are
operating within intended parameters
Create up to 4 reference waveform to compare with measured waveforms
Selectable actions when waveform strays outside the reference limits
Stop acquisition; audible beep, print hardcopy; save waveform to disk
TDS3VID Extended Video Application Module
Adds line count triggering, custom video scan and field rates
Analogue HDTV triggering formats 10801, 1080p, 720p, and 480p
Vectorscope mode with built in 100% & 75% colour bars
Monochrome picture image display on screen
Readout in mV or IRE units
Includes 75Ω terminator
Model
Stock no.
TDS3AAM
TDS3LIM
413-6967
413-6973
Price per
OM
S$
1+
1+
1290·00
1290·00
unit
unit
S$
S$
96
Price per
2342
OM = Order Multiple
Price per
unit
unit
unit
OM
S$
1+
1+
1+
6640·00
7990·00
9570·00
S$
Stock no.
575-602
575-608
575-567
S$
DPO2000 Series
S$
1+
1170·00
www.rssingapore.com
575-602
575-608
575-567
Yes
Yes
Yes
Yes
Yes
Yes
1 Gs/s
Yes
Tektronix DPO2000 series
OM
unit
Stock no.
MSO2012 100MHz, 2-ch
MSO2014 100MHz, 4-ch
MSO2024 200MHz, 4-ch
Lithium ion battery pack for up to three hours of portable
battery operation.
For use with TDS3000B & TDS3000C series Digital
Phosphor Oscilloscopes
420-003
Type
Mixed Signal
I2C
Series
MSO2000
LIN
Display
Colour
RS-232
Time Base Max. 1
100 s/div
RS-422
Vertical Sensitivity Min. 1
2 mV/div
RS-485
Vertical Sensitivity Max. 1
5 V/div
SPI
Record Length
1 M Points/Channel
Sample Rate (Random)
Vertical Resolution
8 Bit
UART
CAN
Yes
Manu. Part No. Channels Bandwidth (MHz) Time Base Min. 1 (ns/div) Rise Time (ns)
MSO2012
2
100
4
3.5
MSO2014
4
100
4
3.5
MSO2024
4
200
2
2.1
Description
TDS3BATC Lithium Ion Battery
Stock no.
First entry-level oscilloscopes with feature-rich tools to
simplify mixed signal design: simultaneous monitoring of
up to 4 analog and 16 digital signals, 1GS/s sampling rate on
analog and digital channels, parallel bus trigger and decode
100 MHz and 200 MHz models
1 GS/s on all channels
1M record length on all channels
5000 wfm/s capture rate
Next-generation digital waveform display
Up to 4 analog channels plus 16 digital channels
Wave Inspectorᓼ navigation and search tools
MSO2012
Large 7” wide-format TFT Display
FilterVuᓽ variable low-pass filter
Mixed Signal Debug
Modern PC connectivity
Define up to 2 serial and/or parallel buses
Parallel bus triggering and decode
Innovative digital probe design
Shallow package saves valuable bench space and simplifies lab-to-lab transport
S$
S$
First entry-level oscilloscopes featuring 1GS/s sampling rate
and optional parallel bus trigger and decode modules.
"Digital phosphor" technology enables real-time intensity
grading of the signal, mimicking the effect of a VT phospor
oscilloscope display.
100 MHz, and 200 MHz models
1 GS/s on all channels
1million sample record length on all channels
5000 wfm/s capture rate
Wave Inspectorᓼ navigation and search tools
Large 7” wide-format TFT Display
DPO2012
Shallow package saves valuable bench space and
simplifies lab-to-lab transport
Modern PC connectivity
FilterVuᓽ variable low-pass filter
Next generation digital waveform display
Define up to 2 serial and/or parallel buses
Parallel bus triggering and decode
Innovative digital probe design
Note: Optional Modules to support serial debug triggering and decode: I2C; SPI; CAN; LIN; RS232/422/
www.nguyenxuong.com
ORDERLINE
65 6865 3433
485/UART
Model
DPO2012
DPO2014
DPO2024
Oscilloscopes
Type
Series
Input Channels
2
4
4
Description
Embedded decode RS232/422/
485/UART DPO2COMP
Embedded decode module
DPO2AUTO
Ethernet connectivity, video
out module DPO2CONN
200 Mhz Passive Voltage
Probe, 1x/10x P2221
Soft carry case for MSO2000/
DPO2000 ACD2000
Oscilloscope DPO2014
Oscilloscope DPO2024
Embedded decode module:
I2C, SPI DPO2EMBD
Oscilloscope DPO2012
Bandwidth
100MHz
100MHz
200MHz
Sample rate
1 Gs/s
1 Gs/s
1 Gs/s
Record Length
1 M sample points
1 M sample points
1 M sample points
Stock no.
Price
per
OM
S$
575-563
unit
1+
1230·00
575-573
unit
1+
1230·00
575-579
unit
1+
698·00
575-585
unit
1+
219·00
575-589
unit
1+
399·00
575-595
575-591
575-614
unit
unit
unit
1+
1+
1+
5760·00
6910·00
1230·00
575-618
unit
1+
4790·00
S$
Stock no.
575-618
575-595
575-591
S$
Tektronix Wavestar
WSTRO, Windows 95/98 NT,
Application Software
Application software designed to capture, analyse,
document and control data from Tektronix digital
storage oscilloscopes
Capture measurement waveforms and data easily
without the need for programming. Setup connections
through the connection wizard select a property, click,
drag and capture measurement into an active application
sheet to analyse on a PC
Six application sheet types:
Y-T graphically view multiple waveforms on a graticule with
same scale and position as the oscilloscope with cursor
measurements, zoom function and annotation.
X-Y display one or more pairs of waveforms in X-Y fashion.
Stripchart plots multiple waveform measurements such as rise times in a classic strip chart format.
Tabular measurement - Capture, store, display, and edit either waveform or data log information as
a table of numbers on corresponding sheets.
Notes prepare simple reports and capture and save instrument hard copies and instrument settings.
Measurement sheets simulate the same measurements from Tektronix digital storage oscilloscopes.
Insert information into Microsoft Officeᓽ or Windowsᓽ applications including Mathcadᓽ
Print banner functions for hardcopy of long record lengths
Automatically detects and captures data changes
Control instrument settings and measurements such as autoset and triggers
Supplied on CD-ROM with manual.
Minimum system requirements: Windows 95/98, NT, Pentium PC, 16MB RAM, CD-ROM drive 4 x or
better, PC serial coms port or IEEE interface port.
Compatible instruments: TDS210, TDS220, TDS320, TDS340A, TDS360, TDS380, THS710, THS720,
TDS3012, TDS3014, TDS3032, TDS3034, TDS3054.
Note: Instruments require RS-232 serial or IEEE port option to be fitted.
Type
PC Software
Stock no.
313-1422
Price per
unit
OM
S$
1+
887·00
S$
S$
PC Based Instruments
Being several instruments in one small unit, PC-based oscilloscopes are lighter and more portable than
traditional test equipment. A field engineer can thereby carry a complete electronics lab loaded onto a
notebook computer.
Compact and portable
Can provide a large and detailed colour display on your PC monitor
Simultaneous views of scope, spectrum analyser and meter modes
Analogue intensity and digital colour display modes
Signal storage is limited only by the PC’s memory
Captured waveforms and instrument settings can be shared easily with others
New functionality through free software upgrades
Can be used with desktop or laptop PCs
Hardware and software in one package: no compatibility problems or complex set-up procedures
Supplied with PicoLog data logging software
PicoScope 6000 Series
The 6402 and 6403 were the first USB scopes to offer a
5GS/s real-time sampling rate. The 6403 and 6404 offer
greatly increased memory which can be used for capturing
long detailed signals such as communication buses or serial
data, with up to 100 million times zoom, or preserving the
high sample rate at the long timebases or for capturing and
saving up to 10000 events in the waveform buffer.
Hi-speed USB 2.0 connection to PC
Built-in arbitrary waveform generator and spectrum
analyser
Advanced features: serial decoding and mask limit testing
built-in
Supports Windows XP, Vista and Windows 7 (32 and 64-bit)
l2C, UART, SPI and CAN bus decoding
Mask limit testing
Supplied with: Hard carry case, four 1MΩ 500 MHz x10 probes, one 2 footed probe stand, PicoScope
6 software package for Windows PCs and laptops and an SDK for third party programming languages
such as LabVIEW, C/C++ and VB, installation guide, USB cable, power supply with UK, US, EURO and
China/Australia mains leads
PC Based
PicoScope 6000
Description
Bandwidth
Number of Channels
Stock no.
PicoScope 6402
PicoScope 6403
689-4690
689-4700
Price per
unit
unit
OM
350 MHz
4
S$
S$
S$
1+ 9750·00
1+ 12950·00
PicoScope 4000 Series
Oscilloscopes
4424
4224
The PicoScope 4000 series high-precision PC oscilloscopes are designed to meet the requirements of
modern electronic engineering servicing, design and debugging. With their high input resolution, they
can detect or trigger on voltage changes of less than 50 μV. This makes them ideal for
electromechanical applications such as monitoring transducers, and for spectral analysis of audio,
noise and vibration. The PicoScope 4000 oscilloscopes are bundled with PicoScope software, 2 or 4
scope probes and a tough carry case.,All PicoScopeᓼ PC Oscilloscopes are powered by the PicoScope
6 Windows software, which frequently receives free updates, feature extensions and improvements.
PicoScope 6 is powerful yet easy to operate. Its 26 automatic measurements, suite of advanced
triggers and many other features can be quickly accessed using standard Windows controls.
Accurate to 1% 12-bit resolution inputs
25, 50 and 100 MHz bandwidths
2 or 4-channel models available
2 channel models with external trigger have a 100kHz bandwidth 20 MSPS waveform generator
32 Msample memory
Fast 80, 125 or 250 MS/s sample rates
USB 2.0 connection and power (USB 1.1 compatible)
PicoScope 6 software for XP, Vista and Windows 7 (32⁄64-bit) included
API compatible with LabVIEW, C, VB, Excel, Delphi, Agilent VEE
Model
PicoScope 4224
PicoScope 4424
Number of channels
2
4
Vertical resolution
12 bits
12 bits
Analog bandwidth
20 MHz
20 MHz
Maximum sampling rate
(real time)
One channel in use
80 MS/s
80 MS/s
Two channels in use
80 MS/s (A+C, A+D, B+C, B+D) 20
80 MS/s (A+C, A+D, B+C, B+D) 20
MS/s (all other combinations)
MS/s (all other combinations)
Three or four channels in use
20 MS/s
Record length (buffer shared
32 MS
32 MS
between enabled channels)
Inputs
Input characteristics
BNC, 1 M ohm || 22 pF
BNC, 1 M ohm || 22 pF
Coupling
Software-selectable AC/DC
Software-selectable AC/DC
Voltage ranges
±50 mV, ±100 mV, ±200 mV, ±500
±50 mV, ±100 mV, ±200 mV, ±500
mV,
mV,
±1 V, ±2 V, ±5 V, ±10 V, ±20 V, ±50 V, ±1 V, ±2 V, ±5 V, ±10 V, ±20 V, ±50 V,
±100 V
±100 V
Accuracy
1%
1%
Overload protection
±200 V
±200 V
Timebase Ranges
100 ns/div to 200 s/div
100 ns/div to 200 s/div
Timebase accuracy
50 ppm
50 ppm
Operating environment
0°C to 45°C for normal operation
Temperature range
0°C to 45°C for normal operation
Humidity
5% to 80% RH, non-condensing
5% to 80% RH, non-condensing
PC connection
USB 2.0 (compatible with USB 1.1) USB 2.0 (compatible with USB 1.1)
Power supply
5 V @ 0.5 A max. (from USB port)
5 V @ 0.5 A max. (from USB port)
Dimensions
200 mm x 140 mm x 35 mm
200 mm x 140 mm x 35 mm
Weight
<0.5 kg
<0.5 kg
Compliance
European EMC and LVD standards European EMC and LVD standards
FCC Rules Part 15 Class A
FCC Rules Part 15 Class A
Description
Number of
Channels
4224
4424
2
4
Stock no.
Price
per
OM
S$
550-394
550-401
unit
unit
1+
1+
1450·00
1670·00
S$
S$
PicoScope 2000
The PicoScope 2000 offers excellent performance and value.
It is an extremely versatile all-in-one full-function
oscilloscope, spectrum analyser, signal generator and
arbitrary waveform generator (AWG). It has a compact
footprint of 100 x 135 mm (3.93&#148; x 5.31&#148;) and fits
neatly into a laptop or travel bag. The small, rugged case has
three BNC connectors; two dedicated input channels and a
dedicated BNC for the signal generator and arbitrary
waveform generator. Power is taken directly from the PC and
uses the full USB 2.0 bandwidth (480 Mbps) allowing a fast
screen update rate without compromising accuracy and
detail.,All PicoScopeᓼ PC oscilloscopes are powered by highend PicoScope 6 Windows software, with updates, feature
extensions and improvements that will remain free for the
lifetime of the product. PicoScope 6 is powerful yet easy to operate. Users benefit from the power of
the PC, and the familiar Windows interface and controls, making the software easy to learn and easy to
use on a daily basis. Data is easily saved in a variety of formats including CSV text, PNG and BMP
images and MATLAB binary files. Drivers and examples are included for LabVIEW, C/C++, Delphi and
VB for integration into custom applications.
Connected and powered via USB 2.0 (480 Mbps)
New products available online every week
96
2343
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
Stock no.
Lightweight and compact size ideal for field use
Compatible with LabVIEW, C/C++, Delphi and VB
Operates with Windows XP and Vista
Supplied with: PicoScope 6 high-end oscilloscope software
Resolution
Accuracy
Analogue
Bandwidth (MHz)
10
25
8 bit
±3 %
Timebase Range
423-5806
Number of Channels
2
Sample Rate Bandwidth Scope Timebase
(s)
(MHz)
Range
100ns/div – 200s/div
100MS/
10
100ns/div – 200s/div
50ns/div – 200s/div
200MS/
25
50ns/div – 200s/div
Description
Stock no.
PicoScope 2204
PicoScope 2205
445-125
445-135
Price per
unit
unit
OM
S$
1+
1+
455·00
870·00
Stock no.
445-125
445-135
S$
S$
PicoScope 2104/2105 USB Pen
Scope
The PicoScope 2105 USB Pen Scope has combined features
which are integral to many high performance bench top
oscilloscopes, with a small, lightweight, ergonomic package
that fits perfectly in the hand. When used in conjunction
with PicoScopeᓼ software, it converts any laptop or desktop
PC with USB port into a powerful oscilloscope, without the
need for additional probes or power supplies. An entry-level
version (PicoScope 2104) accommodates less-demanding
applications.
Up to 100MS/s real-time sample rate
Up to 25MHz bandwidth
Digital ETS enhances repetitive signal sample rate to
2GS/s
Up to 24k sample buffer
Connected and powered by USB port
Compatible with Windows XP SP2 and Vista
PicoScope 2104 ( 536-8799 )
Sample rate (repetitive) 1GS/s using digital ETS
Voltage ranges
±100mV to ±20V
Memory buffer
8000 samples
Input Overload
50V (input to ground)
protection
Power supply
From USB 2.0 (USB 1.1 compatible)
32-bit drivers
Yes – C, VB, Delphi, LabVIEW, Agilent
VEE
Resolution
Accuracy
Description
Analogue Bandwidth (MHz)
PicoScope 2104
10
PicoScope 2105
25
Description
Stock no.
PicoScope 2104
PicoScope 2105
536-8799
536-8812
Price per
unit
unit
Price per
OM
S$
1+
2850·00
unit
S$
S$
S$
S$
Dual Trace
ISO-TECH ISR 622, 20MHz
A general purpose 20MHz dual channel oscilloscope with
6in rectangular CRT tube with red internal graticule.
Triggering modes include: Auto, Norm, TV field, TV line.
8 x 10 1cm divisions
Trigger level lock function eliminates troublesome
triggering adjustment
TV sync triggering for automatic triggering of TV-V and
TV-H signals
Linear focus maintains optimum beam focus
Probe calibration output
Variable hold-off stable display of periodic waveforms
Rise time 17.5ns
Sensitivity 1mV to 5V/Div in 12 steps
Timebase sweep 0.1μs to 0.5s/div in 21 steps
x10 sweep magnification
400V (dc + ac peak) max input
Constructed to EN61010-1 (safety standard) 400V Cat II
Supplied with: mains lead and instruction manual. Probes not included.
Stock no.
S248-8985
Price per
OM
S$
1+
680·00
unit
ISO-TECH ISR 635 35MHz
PicoScope 2105 ( 536-8812 )
2GS/s using digital ETS
±100mV to ±20V
24000 samples
50V (input to ground)
From USB 2.0 (USB 1.1 compatible)
Yes – C, VB, Delphi, LabVIEW, Agilent
VEE
8 bit
±3 %
Timebase Range
Stock no.
20ns/div – 50s/div
536-8799
10ns/div – 50s/div
536-8812
OM
S$
1+
1+
335·00
530·00
S$
S$
Rise time 10ns
High sensitivity, 1mV/div
Vertical sensitivity 5mV/div - 5V/div; 1mV - 2V/div
6" rectangular CRT, internal graticule, 8 x 10V 1cm
divisions
CH1 output, Z axis input
TV synchronisation
ALT triggering function
Variable hold off function
Probe calibration output
Constructed to BS EN61010-1 (safety standard) 400V Cat II
Supplied with: mains lead and instruction manual. Probes not included.
Display mode
CH1, CH2, Dual, ADD Timebase Sweep Time 0.1 μs to 0.5s/div ±3%, 10ns to 50ns ±8% (x10 mag)
CH1 output signal 50mV/div into 50Ω Trigger modes & source Auto, Norm, CH1, CH2, ALT, LINE, EXT
Stock no.
S326-4651
Price per
OM
S$
1+
990·00
unit
S$
S$
HM400, 40 MHz
2-channel analogue oscilloscope
Memory for 6 device settings
Frequency counter function
Component tester
Low power draw, no fan
Supplied with: HM400, power cable, 2 probes1:1 / 1:10
(HZ154), instructions
Dual Trace
HM507 50MHz 100MS/s
100MHz frequency & period counter
7 automatic measurements
SAVE/RECALL of up to 9 stored setups
Selectable analogue real time
Digital storage operation
High resolution, bright CRT display
Autoset function
Built in RS-232 interface
2kB/channel record length & 2 full 2kB reference
memories
Supplied with: 2 switchable x1/x10 probes, manual, mains lead and PC software & operators manual
on CD-ROM.
96
Analogue
Bandwidth
HM507
d.c. to 50MHz (-3dB)
Vertical
Sensitivity
Rise time
Operating
modes
Inputs
1mVdiv to 2mV/div ±5% (x5 mag) dc to
10MHz, 5mV/div to 20V/div ± 3%
<7ns
CH1, ±CH2, CH1 + CH2, ALT, CHOP, Add,
Subtract
a.c.,d.c.,gnd
Sample rate
Channel
Operation
Pre/post
trigger (%)
Timebase
Timebase B
Real Time: 100MS/s Random: 2GS/s
CH1, CH2, ALT, CHOP, ADD, XY
-75% to +100% continuously
100ns to 50ns/div ±2% 1-2-5 sequence
n/a
Automatic
Frequency, duty cycle, Vdc, Vpp, Vp+, Vpmeasurements
Input
1MΩ/18pF
Acquisition Refresh, Roll, Single, XY, Envelope, Average,
Impedance
Modes
Random Sampling, Dot join
Timebase A 0.5s/div to 50ns/div ±3% with variable cal Cursor measurements
Timebase B n/a
Analogue & T, ΔT, 1/Δt (freq), gain, rise time, ratio x,
Digital Mode ratio Y, V, to GND, phase angle
x10 expansion Up to 10ns/div
Digital Mode Pulse count, Vrms, Vavg, Vpk-pk, peak+,
only
peakTrigger
Automatic ≥ 0.5div 20Hz to 100MHz, Normal General
with level control ≥0.5div, 20Hz to 100MHz
Trigger
CH1, CH2 Alternate CH1/CH2 LINE, EXT, AC, Frequency
4 digit (0.01% ±1 digit) 0.5Hz-100MHz
DC, HF, LF, TV
Counter
Digital Functions
Calibrator
0.2V square wave ∼ 1kHz - 1MHz
output
Conversion Low noise 8 bits flash
Power
100 to 240Vac ±10% 50/60Hz 46W
Requirements
2344
OM = Order Multiple a New product to range
Bandwidth
Rise time
Amplitude ranges
Timebase Ranges
Operating modes
40 MHz
< 35 ns (1 mV / cm to 2 mV / cm)
< 8.75 ns (5 mV / cm to 20 V / cm)
1 mV to 20 V
0.2 s / cm → 10 ns / cm
CH1, CH2, ALT, CHOP, total, differential, XY
Stock no.
a488-160
Price per
unit
Trigger bandwidth
Trigger coupling
80 MHz
AC / DC / LF / TV
Max. Input voltage
Dimensions (WxHxD)
400 V (DC + peak AC)
285 x 125 x 380 mm
OM
S$
1+
940·00
S$
S$
ISO-TECH 6051 50MHz with
Frequency Counter & Panel
Setup
The ISR6051 with built in 6 digit frequency counter, cursor
and numerical readouts make waveform observation and
measurement fast and accurate. Setup save/recall enable
regular setups to be recalled for ease of use and production
test applications.
Rise time 7/50 ns
8 x 10 1cm divisions
Cursor readout measurement of ΔV, ΔT, 1/ΔT
50Hz to 50MHz frequency counter, 6-digits, accuracy ±0.01%
MEM save/recall of up to 10 front panel setups
TV sync triggering for automatic linear focus maintains optimum beam focus
Variable trigger hold off for stable display of periodic waveforms
ALT MAG functions (x5, x10, x20)
Trigger modes: Auto, Norm, TV field and TV line
Sensitivity 1mV to 20V/div in 14 steps
Timebase 0.2μs to 0.5sec/div in 20 steps
400V (d.c. + a.c. peak) max input to CH1 and CH2
Constructed to EN61010-1 (safety standard) 300V Cat II
Note: Probes are available separately
Supplied with: Mains lead and instruction manual.
Description
ISO-TECH 6051
+ RS Cal
Stock no.
S514-4896
S514-5546
Price per
unit
unit
OM
S$
1+
1+
910·00
1060·00
S$
S$
www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
ScopeMeter 192C, 215C & 225C
Dual Trace 35MHz, 100MHz & 200MHz
HAMEG HM2005 (200MHz)
Timebase range 0.5s/div-20ns/div (A) 20 ms/div-50n/div
(B)
Rise time <1.75 ns
Vertical sensitivity 5mV/div-5V/div; 1mV/div (x5Mag)
Microprocessor controlled front panel
CRT readout and cursor measurements
Autoset function
SAVE/RECALL of up to 9 stored setups
Dual time base with variable hold off
DC to 250MHz triggering, ALT trigger mode
Y axis delay line for leading edge of even low repetition signals
XY mode, Probe calibration output, built in RS-232 interface
Windows 95/98 software supplied enables remote control from a PC
Supplied with: 2 switchable x1/x10 probes, manual, UK and European mains lead and remote control
software
Trigger B modes
d.c. to 200MHz (-3dB) (x5mag b/w
10MHz)
Display mode
CH1, CH2, DUAL, ADD, ALT, CHOP,
XY
Input coupling
ac, dc, gnd
Input impedance
1MΩ/15pF
Maximum input voltage400V (dc + ac peak ) Cat II
Sweep magnification x10 to 2ns/div ±5%
Control
NORM with level control and ±
slope
Autoset, Manual, Remote (RS-232)
Component Tester
7Vrms, 50Hz 7mA via 24mm sockets
Power requirements
Bandwidth
Rise Time
Timebase Range
Trigger A modes
AUTO, NORM, TV, ALT, EXT
Vertical Sensitivity
100-240Vac.±10%, 50/60Hz
200 MHz
<1.75 ns
0.5s/div-20ns/div (A)
20 ms/div-50n/div (B)
5mV/div-5V/div;
1mV/div (x5Mag)
Coupling
ac, dc. HF, LF, NR (noise reduction)
Bandwidth
Stock no.
389-1073
Price per
unit
OM
S$
1+
2830·00
S$
S$
ScopeMeters
Handheld, battery powered, 2 channel oscilloscopes with up to 200MHz banswidth and 2.5 GS/s real
time sampling per output.
Fluke 190 Series ScopeMeter Features
27500 points per input record length using ScopeRecordᓽ-Roll captures complete motion profiles,
and UPS-, power supply- and motor start-ups. 100x zoom for detailed analysis of fast intermittent
events
Record length 3000 points per channel
Advanced triggering capability. Connect-and-Viewᓽ automatic triggering for simplicity, a full range
of manual triggering modes plus external triggering (third input) for complex timing
Stop-on-Trigger in ScopeRecord mode stores and analyzes pre-trigger waveform data
Automatic capture and replay of 100 screens, allows instant replay as a live animation or pictureby-picture
Digital persistence for analysing complex dynamic waveforms like an analogue scope
28 Automatic waveform measurements
Cursors, Zoom and real time clock. For analysis of signal details, long records and TrendPlotᓽ
144mm LCD display, 190B range – monochrome, 190C range – high resolution colour
Vpwm function for motor drive and frequency inverter applicationsIndependently floating isolated
inputs. Up to 1000V between inputs, references and ground
Waveform reference for visual comparisons
5000-count true RMS multi-meter & dual channel TrendPlotᓽ paperless recorder for up to 8 days of
trend and intermittent fault analysis
Save up to 2 recordings for later analysis and recall
Save up to 10 screens and setups
Print screens directly or download data to a PC for later analysis and documentation with
Flukeviewᓼ software
Four-hour rechargeable NiMH battery pack
Complies with EN61010-1 (safety standard) 1000V CAT II and 600V CAT III
Fast display update rate for seeing dynamic behaviour instantaneously
Dimensions (HxWxD): 256 x 169 x 64mm
Weight: 1.95kg
Number of inputs
Number of digitizers
Input sensitivity
Input impedance
Acquisition modes
Trigger types
Glitch capture
Maximum record length
Automatic Scope
Measurement
Cursor measurements
2 plus external/DMM input isolated from each other and ground
2
5 mV to 100 V/div
1 MΩ ± 1% / 15 pF ± 2pF
Normal, single shot, ScopeRecordᓽ, roll glitch capture
Connect-and-Viewᓼ Free Run, Single Shot, Edge, Delay, Video, Video line, Selectable pulse
width and External
50 nsec (5 μsec/div to 1 min/div)
27500 points per input ScopeRecord-roll mode (10 md/div -2 min/div) 3000 points per input in
Scope mode
VDC, VAC RMS, VAC+DC, Vpeak min, Vpeak to Vpeak, frequency (Hz), positive/negative pulse
width,
positive/negative duty cycle, Rise time, Fall time, Amp AC, Amp DC, Amp AC+DC, Power
factor,
Watts, VA, VA reactive, Phase, Temperature °C, Temperature °F, dBV, dBm into 50Ω and
600Ω
Value at cursor, difference between cursors, time of day, time difference
Frequency spectrum analysis (FFT)
N-cycle triggering mode for stable live signal image of complex
waveforms
Dual slope triggering for acquisition on both rising and falling edges,
useful for analysing digital data streaming and single shot
phenomena
Cursor limited automatic measurements allow Vrms and power
measurement on user defined portion of a waveform
Continuity: beeper on <50Ω (±30Ω)
14.4cm full colour LCD
Maximum record length in Scope mode is 3000 points per input
channel, allowing for high time resolution signal analysis using
Zoom
Maximum record length in ScopeRecord mode is 27,500 points per
input or more (5 ms/div - 2 min/div)
225C
Two inputs plus external/DMM input, all isolated from each other
and from ground
Glitch capture up to 3ns using pulse width triggering; 50ns peak detect at 5μs/div to 1min/div
Dimensions (HxWxD): 256 x 169 x 64mm; Weight 2kg
The Fluke 215C and 225C add Industrial Bus Health Test to the Fluke 190C-series of Color
ScopeMeters. Industrial Buses (’Field Buses’) link machinery on the factory floor to each other, to
sensors and actuators and to centralized computers or control systems. The 215C and 225C offer
extensive capabilities to test the functioning of the industrial bus by analyzing the electrical signals
on the network. Supported Fieldbus types are: AS-i (EN50295, 166 kb/s); CAN-bus (ISO-11898, up to
1 Mb/s); Modbus (EIA-232 up to 115 kb/s; EIA-485 up to 10 Mb/s); Foundation Fieldbus H1 (61158
type 1, 31.25 kb/s) ; Profibus DP (EIA-485 up to 10 Mb/s); Profibus PA (61158 type 1, 31.25 kb/s);
Ethernet 10Base2 (coaxial); Ethernet 10BaseT (UTP, 10 Mb/s); Ethernet 100BaseT (100 Mb/s); RS-232
(EIA-232, up to 115 kb/s); RS-485 (EIA-485, up to 10 Mb/s).
The BHT190 accessory (included with the 225C & 215C) is a set of 3 bus system break-out adapters
for DB-9, M12 and RJ-45 connection systems. Each contact of the connector is made accessible for
hooking up a probe. The BHT190 is optionally available to support the Fluke 125.
Note: Full functionality of Fluke 199C & 196C included in 225C & 215C respectively.
Supplied with: Manufacturer calibration certificate; rechargeable battery pack (fitted); mains adaptor/
battery charger: 2 each (1 red and 1 grey); VP200 voltage probe sets; AS200 probe accessory sets;
shrouded multi-meter test leads. BHT190 Bus Test Connection support supplied with 225C & 215C
only.
734-0715, 734-0712 & 734-0721 supplied with universal plug and SCC190 kit (Hard shell carry case, OC4
USB interface cable, SW90W FlukeView for Scopemeter Windows software)
Glitch Capture
Input Sensitivity
Description
215C
225C
Description
50 ns
Timebase Range
0.002 - 100 V
Bandwidth (MHz)
100
200
Stock no.
215C
225C
662-2375
662-2366
Price per
unit
unit
5 ns/div - 2 min/div
Sample Rate
1 GS/s
2.5 GS/s
OM
S$
1+
1+
7769·00
8509·00
S$
Stock no.
662-2375
662-2366
S$
ScopeMeter Accessories
ScopeMeter 190 Series Accessories
SW90W FlukeView software for Windows: transfers screens, waveforms and
measurement data to a PC for printing, or to import data to other programs; stores and retrieves
waveforms with text annotations and create a library for easy reference and comparison; gathers
measurement data and enables cursor measurements for waveform analysis, including analyzing
harmonics.
VPS210-R (Red) VPS210-G (Grey). 600 V CAT III / 1000 V CAT II rated: 10:1 voltage probe; hook clip
for probe tip; 4mm test probe for probe tip; ground lead with hook clip; ground lead with minialligator clip. 30 V CAT II rated: ground spring for probe tip.
Description
Stock no.
SW90W software
342-4588
SC190 kit (FlukeView software, PM9080/001 RS232 interface adaptor/cable, C190 case)
334-2458
C190 Hard Case
334-2379
C195 Soft Case
334-2385
PM9080/101 RS-232 interface cable for use with Scopemeter 93, 95 & 97
205-738
VPS210-R (Red) 4mm test probe, leads, clips
384-878
AS200-R (Red) 2mm test probe, leads, clips
394-4509
BP190 battery pack
366-6041
Description
SW90W software
SCC190 Accessory Kit
C190 Hard Case
C195 Soft Case
Isolated RS-232 cable
VPS210-R 4mm test probe kit,
Red
Red test probe, leads & clips
BP190 battery pack
Stock no.
Price
per
OM
S$
342-4588
334-2458
334-2379
334-2385
205-738
384-878
unit
unit
unit
unit
unit
unit
1+
1+
1+
1+
1+
1+
457·00
898·00
296·00
280·00
323·00
334·00
394-4509
366-6041
unit
unit
1+
1+
137·00
258·00
S$
S$
96
Many more leading brands from over 2,500 suppliers available online
2345
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
Bandwidth
Sample Rate
Fluke Industrial Scopemeters
These small, lightweight handheld digital oscilloscopes are ideal for use by technicians working in
service, maintenance and installation applications. Features include:
Intuitive menu driven operation
Reliable automatic (and manual) triggering including motor drives and video
Connect and Viewᓽ hands off operation provides stable, reliable and repeatable display of signals
without touching a button
DMM measurements including VDC, VAC True rms, Hz, duty cycle, pulse width, dBV, dBm, phase A
to B, crest factor, Ohms, continuity, frequency, diode and capacitance
40ns glitch capture
Dual channel Trendplotᓽ displays graphs of max. and min. readings with time and date stamp
High brightness, high contrast LCD display
Single shielded test lead type for each channel is used for all measurement including DSO and
DMM functions
Rugged and splash proof design with integral holster for reliable operation.
Safety designed to meet IEC 1010-1 Cat III, 600V for industrial power systems
Oscilloscope mode
Volts/Division
Record length
Screen/setup memories
Video triggering
Pre & post trigger
Multi-meter mode
Channels
Display resolution
Basic d.c. accuracy
Capacitance
5mV - 500V
512 bytes
2/10
NTSC, PAL, SECAM, line & field selectable
±10 divisions
Stock no.
S240-9522
Price per
unit
Multimeter Accuracy d.c.
Rise Time
Timebase Range
OM
S$
1+
2411·00
S$
0.5 %
<17.5 ns
20 ns - 60 s
S$
Dual channel DSO and integrated dual channel 5000
count True rms DMM
Cursors measurements; Single: Average, Min, Max
(from start of recording in ROLL mode) Dual: ΔV 1/T Rise Time, Fall Time
VPS40 x10 probe for 40MHz bandwidth scope measurement
7 hour battery operation and fast recharge
70MHz Frequency measurement
Supplied with:
PM8907 mains adaptor/charger,
VPS40 10:1 probe
STL120 shielded test leads set
BNC adaptor
BP130 NiMH rechargeable battery pack
User’s manual
Stock no.
Sa451-7760
Price per
unit
Multimeter Accuracy d.c. +/- (5% +5 Counts)
Rise Time
8.75 typ. ns
Timebase Range
10 ns - 60 sec
OM
S$
1+
2958·00
S$
S$
Fluke 125 Industrial ScopeMeter
The compact ScopeMeter 120 Series are the rugged solution to industrial testing
incorporating both Oscilloscope, DMM and paperless recorder in one easy to use
instrument. The Fluke 125 extends the capability further by incorporating a Bus
health mode. Industrial Buses (or "Field Buses") link the machinery on the factory
floor to each other, to sensors and to a central computer and control system. The
Fluke 125 offers extensive capabilities to test the proper functioning of the
network by analyzing the electrical signals.,The bus health function is used to
investigate the electrical performance of the communications system giving a
good or not good indication. Most types of field bus are supported.,In addition
the 125 incorporates Power, Harmonics and RPM Measurement.
Dual input 40MHz Oscilloscope
Two 5000 count True RMS Multimeter’s
Bus health function for Industrial busses
Connect & View Triggering
Power and Harmonic Measurement
High Resolution, low impedance measurement for motor windings
Direct reading of RPM from external pulses
Measurement of Vpwm for motors
i400 Current clamp included
Save & Recall functions
Contact RS for calibration requirements
Supplied with: i400 Current Clamp accessory, Mains adapter/charger, Manual, Test leads, Battery
pack, VPS40 Voltage probe.
96
Timebase Range
10ns/division to 1min/division
Bus Health (Supported Busses) AS-I Bus, CAN-bus, Interbus, ControlNet, MOD-bus, Foundation Fieldbus, Profibus,
Ethernet coax TP, RS-232, RS-485, user defined
Power
Watts, VA,VAR, Power Factor
Harmonics
To 33rd (fundamental 16 2⁄3, 50,60 & 400 Hz systems)
High Resolution Low
50.00 Ohms Full Scale
Impedance Measurement
RPM
2 or 1 rotations per pulse, 1 rotation per 2 or 4 pulses
Current Measurement using 400A
i400 Clamp
Safety rating
Cat III 600V
2346
Yes
40 ns
Resistance
Stock no.
Fluke 125, UK mains plug
Fluke 125, ANZ mains plug
Fluke 125, SG mains plug
S315-999
372-144
255-077
Price per
unit
unit
unit
1 MOhm/12 pF
OM
S$
1+
1+
1+
3131·00
4650·00
3922·00
OM
S$
1+
180·00
S$
S$
Description
Stock no.
C120 Hard carry case
260-0028
Price per
S$
S$
unit
The 190 Series
ScopeMeters are the first
two and four channel
industrial portable
oscilloscopes allowing
measurements in harsh,
hazardous and dirty
environments with the
highest CAT IV 600V safety
rating. With these features
the ScopeMeter 190 Series
II can be used for measurements in Single-phase and Three-phase industrial distribution up to outside
and service entrance. The standard features like TrendPlotᓽ, Connect-and-Viewᓽ triggering, and
ScopeRecordᓽ allow quick diagnosis of industrial machinery, automation and process controls
problems. The Automatic capture and the display of the last 100 screens allows the review of observed
anomalies. The full version of the software and the accessories for ScopeMeter 190 are available
separately see stock number 716-7434
Four electrically isolated inputs
CAT III 1000V/ CAT IV 6000V overvoltage categories.
Real-time sampling rates up to 2.5 GS/s and 400 ps resolution
Deep memory: 10,000 samples per channel waveform capture so you can zoom in on the details
Single shot, pulse width, and video triggering
Isolated USB ports for memory devices and PC connectivity
IP-51 rated for dust and drip proof to withstand harsh environments
Li-ion battery technology offering 8 hour battery life.
Supplied with: Set of four probes, Hanging strap, USB cable, Li-ion battery BP291, a FlukeView demo
package and users manuals on CD-ROM
734-0702 & 734-0706 additionally supplied with SCC290 kit (Hard shell carry case, OC4 USB interface
cable, FlukeView for Scopemeter Windows software)
Fluke Industrial ScopeMeter 124
Bandwidth
40 MHz
Sample Rate
2.5 Gs/s (Repetitive)
Multimeter Accuracy a.c. +/- (2.5% +1 5 Counts) (60 Hz - 20 kHz)
Description
0.005 - 500 V
512 Min/Max Points per
Input
2
Multimeter Accuracy a.c. Volts 2.5 %
ΔT, 1/ΔT, V, ΔV, rise- and Multimeter Accuracy d.c. Volts 0.5 %
fall-time
20 ns - 1 min/div
Multimeter a.c. Volts
0.5 - 5 - 50 - 500 - 1250 V
8.75 ns
Multimeter d.c. Volts
0.5 - 5 - 50 - 500 - 1250 V
1.5 G s/s
Number of Digitisers
2
Fluke Industrial ScopeMeter 190 Series II
Dual channel DSO and integrated dual-channel 5000 count True rms DMM
5 hour battery operation and fast recharge
Supplied with:
Mains adaptor/charger
Test leads set
BNC adaptor
Rechargeable battery pack
User’s manual
Contact RS for calibration requirements
20 MHz
1.25 G s/s
+/- (1% +10 Counts)
Timebase Range
Rise Time
Maximum Real Time Sampling
Rate
Continuity
Glitch Capture
Input Sensitivity
Maximum Record Length
Accessories
2
5000 counts
0.5%
50nF - 500μF
Fluke Industrial ScopeMeter 123
Bandwidth
Sample Rate
Multimeter Accuracy a.c.
Number of Inputs
Cursor Measurements
40 MHz
25 MS/s
OM = Order Multiple a New product to range
Type
Series
Channels
2
2
4
4
4
4
Handheld
190
Time Base Min. 1 (ns/div)
10
2
5
5
5
5
Manu. Part No.
Bandwidth
(MHz)
FLUKE 190-062/
UK
FLUKE 190-202/
UK
FLUKE 190-104
FLUKE 190-104
FLUKE 190-204
FLUKE 190-204
60
Stock no.
Display
Colour
Time Base Max. 1
4 s/div
2 min/div
2 min/div
2 min/div
2 min/div
2 min/div
Price
per
OM
S$
Sa736-2324
unit
1+
6610·00
200
Sa736-2336
unit
1+
9342·00
100
100
200
200
Sa716-7396
a716-7365
Sa716-7387
a716-7361
unit
unit
unit
unit
1+ 7020·00
1+ 11751·00
1+ 7958·00
1+ 11751·00
S$
Stock no.
736-2324
736-2336
716-7396
716-7365
716-7387
716-7361
S$
Accessories
Description
190-204 & carry case, Aus/NZ
Plug
Stock no.
a728-0701
Price
per
OM
S$
unit
1+
8951·00
S$
My Account
www.rssingapore.com
S$
www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
Fluke Industrial Scopemeter Accessories
Agilent U1600 Series
Accessories for Fluke ScopeMeter 123
and 124
Description
SCC120 Accessory Kit
ITP120 Isolated Trigger Probe
(with 9V alkaline battery)
C125 Soft Carry Case
C120 Hard Carry Case
BP.120 Rechargeable Ni-CAD
battery pack 4.8V 3000mAh
PM8907 UK-type Battery
Charger
Stock no.
Price
per
OM
S$
342-4594
260-0078
unit
unit
1+
1+
629·00
554·00
260-0034
260-0028
548-8938
unit
unit
unit
1+
1+
1+
64·50
180·00
169·00
480-4137
unit
1+
178·50
U1600 Series
S$
S$
Description
U1602A 20MHz Aus/NZ
U1604A 40MHz Aus/NZ
U1602B 20MHz BS1363
U1602B 20MHz USB host
U1604B 40MHz BS1363
U1604B 40MHz USB host
TekScopes
Accessories for the DPO 4000
Series
Accessories for DPO 4000 series oscilloscopes
A 1.5 GHz active probe
A 2.5 GHz active probe
A 30 A and 120 MHz AC/DC current probe
A Tpa-BNC adaptor
A GPIB adaptor to allow conversion from the Tektronix GPIB standard
to USB
A soft carrying case
Description
Stock no.
30A current probe
Tpa-BNC adapter
661-3289
628-7540
Price per
OM
S$
1+
1+
6030·00
865·00
unit
unit
S$
S$
Accessories to complement and extend the features of
Tektronix TekScopes:
P5102 high voltage oscilloscope probe Fully
insulated enabling 1000V signals to be measured up to
600V above ground potential
A621, A622 current probes Industrial style clamp-on
probes with mV outputs, these probes enable current
waveform measurements on all TekScopes. A621 is an
essential accessory for power & current measurement
with the THS720P
A622
100A peak
50mA
10mV/A, 100mV/A
11.8mm Ø
d.c.-100KHz
Oscilloscopes, DMMs, meters*
BNC
* Included with probes BNC to shielded banana plug adaptor
Model
A621 Current Probe
A622 Current Probe
Stock no.
851-218
851-224
Price per
unit
unit
OM
S$
1+
1+
1100·00
1120·00
Price per
unit
unit
unit
unit
unit
unit
OM
S$
1+
1+
1+
1+
1+
1+
2730·00
3400·00
2149·00
2388·00
2684·00
2923·00
S$
S$
S$
S$
Frequency range 150kHz to 1300MHz (PSA1301T);
1MHz to 2700MHz (PSA2701T)
Full colour TFT screen, 480 x 320 pixels
Highly compact handheld format weighing less than
500 grams
Integrated tilt stand for bench top use
Fully adjustable centre frequency and span in 1kHz
steps
Choice of centre plus span or start plus stop setting
Zero span mode with AM and FM audio
demodulation
PSA1301T
PSA2701T
Resolution bandwidths of 280kHz or 15kHz
(PSA1301T); 1MHz, 280kHz, 15kHz (PSA2701T)
-93dBm typical noise floor, -20 or 0dBm reference level
Sweep modes of continuous, single, peak hold and average
Twin markers with readout of frequency and amplitude plus difference values
Smart marker movement with selectable peak finding
Unlimited storage for waveforms, set-ups and fully annotated screens under user defined file
names
Easy data transfer to PC for analysis, documentation and printing
Up to 4 hours continuous system operation from full charge, selectable auto switch-off to conserve
power
Integrated handheld computer providing word processing, spreadsheets, appointments diary,
graphics viewing, web, email, etc.
Handheld computer can be removed for stand-alone use when required
Large range of third party programs available including many for engineering, science and
mathematics
Model PSA2701T currently unavailable
Supplied with: Palm T|X handheld computer, mains adaptor/charger, USB lead, SD memory card,
memory card reader, support CD and instruction manuals.
The WB-ANT wideband telescopic antenna 493-156 is for general purpose applications where absolute
measurements of field strength are not required. The high quality unit has a knuckle joint hinge and an
impedance matching transformer in the base, terminating with an SMA connector suitable for direct
connection to the PSA1301T or PSA2701T. Length is adjustable between 7cm and 34cm. Useful
bandwidth is 25MHz to 1.9GHz. Resonant frequency as a quarter wave mono-pole is adjustable
between approximately 220MHz and 1.07GHz.
Display
Display Type
Waveform Area
Waveform Traces
Default Annotations
Control
Frequency
Frequency Range
Setting Modes
Setting Resolution
Span
www.rssingapore.com
678-0743
678-0752
S697-8877
697-8886
697-8889
697-8883
PSA1301T 1.3GHz and PSA2701T,
2.7GHz Portable Spectrum Analyser
TekScopeᓽ Accessories
A621
2000A peak
100mA
1mV/A, 10mV/A, 100mV/A
54mm Ø
5Hz-50kHz
Oscilloscopes, DMMs, meters*
BNC
Stock no.
U1602A
Handheld Spectrum Analysers
TekScopes Accessories
Model
Maximum input current
Minimum input current
Current ranges
Maximum conductor size
Frequency range
For use with
Termination
Full-featured handheld oscilloscopes that offer maximum
versatility for current and future needs: dual channel with
built in DMM and recorder functions.
U1600B models are safety orange
U1602 models have DWM (Dual Waveform Math), U1604 models
have DWM+ FFT Function (Fast Fourier Transform)
200 MSa/s sampling rate
125 KB memory depth
Colour LCD display
6000 count Digital Multimeter
Recorder capability
Standard USB 2.0 Full Speed IO Interface
Host interface allows connection to memory devices for
waveform storage
Dimensions 24.1 (H) x 13.8 (W) x 6.6 (D) cm
Supplied with: 2 probes, Ni-MH battery pack 7.2V 4500mA, DMM
test lead, ground alligator clip, hook clip, USB cable, power cord and
AC adaptor, Quick Start Guide, Product Reference CD-ROM,
Certificate of Calibration, test report
Frequency Stability
Markers
Marker Modes
Marker Accuracy
Demodulation
Amplitude
Displayed Amplitude Range
Marker Resolution
Reference Level
Linearity and Accuracy
Noise Floor
Sweep
Sweep Modes
3.7" (9.4 cm) backlit colour TFT, 480 x 320 pixels (half VGA)
300 x 320 pixels (320 samples), 8 x 10 division graticule
Live trace and Reference trace (selectable) in different colours
Centre Freq., Span (or Start + Stop), Ref. Level, RBW, Marker Frequencies, Marker
Amplitudes, Sweep type, Attenuator setting
Choice of Hard Key or Touch Screen control for all functions
150kHz to 1300MHz (PSA1301T), 1MHz to 2699MHz (PSA2701T)
Centre + Span, or Start + Stop, or Zero span with demodulation
1kHz (6.5 digits maximum)
320kHz to 1299.85MHz or zero span (PSA1301T); 1MHz to 2699MHz or zero span
(PSA2701T)
± 10 ppm ± 3 ppm/year
Single or dual markers, differentiated by colour
Manual scroll or automatic peak finding
0.3% of span ± 0.1kHz
AM/FM selectable (zero span mode), variable level output
80dB (10dB/div) or 40dB (5dB/div with vertical panning)
0.1dB
Reference Level Selectable as -20dBm or 0dBm
Linearity <±1dB, Reference level accuracy <±2dB
Average displayed noise floor better than -90dBm (ref. level -20dBm, RBW 15kHz)
Continuous, Single, Peak Hold, or Average (2 to 256 sweeps)
Visit our website for additional price information and exciting promotions
96
2347
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
Resolution Bandwidth (RBW)
Storage Capability
Trace Storage
Set-up Storage
Screen Storage
Connectors
RF Input
Audio Out
USB Through
Power Input
Handheld Computer Type
Power Sources
Battery Operation
External Power
General
Size and Weight
Safety and EMC
Pulse output
LogicView threshold
280kHz or 15kHz (PSA1301T); 1MHz, 280kHz or 15kHz (PSA2701T)
Internal NiMh batteries giving typically 4 hours operation
External power supply/charger, 100V to 240V universal input
169 x 97 x 47mm, 480g
Complies with EN61010-1 and EN61326
Description
PSA1301T 1.3GHz Spectrum
Analyser
PSA2701T 2.7GHz Spectrum
Analyser
Stock no.
Storage for unlimited number of traces with user filenames
Storage for unlimited number of set-ups with user filenames
The whole screen area can be stored as a bitmap for printing or viewing. Unlimited
number of screens with user filenames
SMA connector, 50Ω impedance; VSWR 1.5:1 typical
3.5mm phones jack for demodulated audio
Mini USB socket giving direct access to USB of the handheld computer
1.3mm power jack for external power and recharging
Palm T|X, 312MHz Intel Xscale processor, 128MB Flash Memory, 480x320 portrait/
landscape screen, WiFi, Bluetooth, SD/SDIO or MMC card expansion, compatibility with
Word, Excel, Powerpoint and Outlook.
Stock no.
Price
per
OM
S$
528-3115
unit
1+
2350·00
155-434
unit
1+
3020·00
S$
S$
-10V to +10V in 0.1V steps
-4V to +4V in 0.1V steps
621-5113
Price per
unit
OM
S$
1+
4030·00
S$
S$
S$
S$
Passive Oscilloscope Probes
Agilent Passive Probes
General purpose probes designed for optimal performance
with oscilloscopes. They feature a durable cable and a solid
stainless steel probe body encased with a hard, fracture-resistant plastic.
General purpose retractable hook tip - hooks onto wires and test points for
hands-free probing
Ground bayonet - provides short, flexible ground lead for high-frequency
measurements
General purpose alligator clip ground lead - allows for versatile grounding
2 tags in each colour: orange, white, blue and green (by placing tags at
both ends of the probe cable, users can quickly identify probes)
Rise time (calculated): <17.5 ns
Bandwidth
Attenuation
150 MHz
10:1
Stock no.
714-0035
Price per
unit
Range
OM
S$
1+
285·00
400 V
S$
S$
Accessories
Description
Stock no.
Carrying Case
536-1681
Price per
unit
OM
S$
1+
60·50
S$
S$
CircuitMaster 4000M Mixed Signal Circuit
Analyser
Tektronix Oscilloscope Probes
High quality passive voltage probes suitable for use with
Tektronix oscilloscopes or as general purpose replacements.
Each probe features compensation trimmers to allow
matching to instruments.
Supplied complete with accessories
Rated voltage CAT II 300V rms, CAT I 400V rms
Attenuation 10X
Compensation Range
Bandwidth 100 MHz Compatibility
15 - 35 pF
TDS3012, TDS3014
CircuitMaster 4000M Mixed Signal Circuit
Analyser
The CircuitMaster is a unique circuit test instrument,
designed with two aims in mind: -,To simplify the safe
probing of fine pitch PCBs.,To combine traditional and new
test methods in one instrument.,On fine pitch ICs and tiny
components, probing component pins is difficult, and there is
a constant risk of damage by shorting pins. With traditional
instruments probing is &#147;blind&#148; while instrument
controls are adjusted. The CircuitMaster uses full automatic
ranging to eliminate adjustments during probing, so the
operator can continuously view the pin. In addition the CircuitMaster combines several types of
instrument functions, further reducing probing operations without reducing measured information.
Multiplexed DSO, DVM, function generator, VI tester, FirmFlex tester
Simultaneous DC voltage (0.1%) and AC waveform (100MHz) measurement
Auto and cursor waveform analysis, including store and compare
VI test for power off board diagnosis with flexible ranges for testing a wide range of circuits
including configurable pulse outputs for checking gated devices (e.g. triacs) and comparison to
reference VI curves for rapid identification of faulty components.
FirmFlex powered circuit test depicts on a colour coded display the drive strength of a circuit
facilitating the detection of broken tracks, high impedance outputs, short circuits etc. that passive
test equipment cannot diagnose.
Additional 40 channel MultiWay connector for automatically capturing multiple signals from a
device or board without having to manually probe
SignalTrack injects programmable signals via channel 1 for rapid signal tracing through suspect
circuitry via channel 2
LogicView adds 4 digital channels to 2 analogue channels for comprehensive mixed signal analysis
Colour coded logic threshold scales identifies signals in a “mid High /mid low” condition
WaveStack uses internal memory in conjunction with a footswitch to provide hands-free waveform
storage and review after probing. Multiple stored waveforms can be posted simultaneously onto
the display
USB interface for saving/loading settings, waveforms and updates
CircuitLink PC software for off line file storage, multiple save and compare and for use with multiple
CircuitMasters
Comprehensive automatic measurements including voltage (e.g. amplitude, rms), time (e.g.
frequency, rise time, slew rate), pulse (e.g. overshoot, duty cycle) calculations
Supplied with: Mains power lead UK and European ,2x Oscilloscope Probes X10/X1,MultiWay Cable
Assembly which incorporates an integral LogicView IC pin clips,40 way 0.6&#148; DIL test clip, 16 way
0.3&#148; DIL test clip ,BNC to 4mm Adapter,Red/ Black 4mm Probe Set,USB
cable,Footswitch,Operator&#146;s manual,CD with PC CircuitLink software and drivers
96
Supply voltage
Interfaces
Display type
DSO bandwidth
DSO sample rate
DSO resolution
Maximum input
AC accuracy
Channels
Input impedance
Timebase
Sensitivity
Input coupling
Trigger coupling
Trigger mode
DVM Resolution
DVM accuracy
Stimulus output
Stimulus frequency
Stimulus waveforms
Stimulus source resistance
2348
230/240V AC or 110V AC (auto switch) 50/60Hz
USB, footswitch, BNC, MultiWay, 4mm
Colour LCD 320 x 240 pixel
100MHz
50MS/s single shot, 250MS/s – 25GS/s in ERS mode
10 bits maximum, 8 bits on 10mV/div and 20mV div ranges
+/-200V DC or peak AC, +/-25V in VI or FirmFlex mode, +/-12V LogicView inputs
1% of full scale, 5% on 10mV and 20mV ranges
2 analogue, 4 digital plus external trigger
1M / 50pF
1ns/div to 2s/div in 1-2-5 sequence
10mV/div to 10V/div in 1-2-5 sequence
DC, AC, ground
DC, AC, LF reject, HF reject from ch1, ch2, ext or FG (internal)
Auto, normal, single shot
24 bits (approx 0.1uV on 10mV/div, 162uV on 100V/div)
0.1% of range full scale +/-1LSB
+/-0.5V to +/-25V bipolar/unipolar (for VI, FirmFlex, SignalTrack)
10Hz to 100kHz in 1-2-5 sequence
Sine, triangle, ramp, square, pulse
100R to 1M in decade sequence
OM = Order Multiple a New product to range
Stock no.
349-8034
Price per
unit
OM
S$
1+
317·00
Tektronix 500MHz Passive Probes
P6139B & P5050B
The P6139B and P5050B are high
bandwidth, high impedance probes
featuring a small probe head and sharp
tip that make it easier to probe dense circuitry. The P6139B
and P5050B share similar electrical specifications but
support Tektronix oscilloscopes with different
compensation ranges.
Note: The P6139B and P5050B are identical from a
specifications perspective with the P6139A ( 293-4309 ) and
P5050 ( 697-8710 ). From a mechanical perspective, the ’B’
versions are of sleeker design, have a sharper tip and are
compliant with March 2011 safety updates (UL approved).
Outstanding electrical performance
Rugged and easy to use
Compact probe head for probing small geometry circuit elements
Small probe body for enhanced visibility to the device-under-test
Cable length 1.3m
Replaceable probe tip cartridges
Large accessory set for versatile connectivity
TekProbe interface for direct BNC connection for oscilloscopes with 1MΩ inputs
Integrated oscilloscope and probe measurement systems feature intelligent communication that
automatically scales and adjusts units on the oscilloscope display
Type
Attenuation
Passive Probe
x10
Stock no.
a725-6604
Price per
unit
Bandwidth
OM
S$
1+
720·00
www.rssingapore.com
* manufacturers information unavailable at time of printing
500 MHz
S$
S$
www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
PMK Passive Probes
Attenuation
Cable Length
A range of high performance miniature passive probes with
BNC connector or 4 mm plugs to suit several instrumants. All
probes are equipped with spring loaded needle sharp tips.
Two sizes of spring tip are available along with a solid
unsprung tip. Basic probe accessories are provided with each
probe, or are available as replacement kits.
Stock no.
188-4770
Stock no.
1:1 25MHz Probe
10:1 150MHz Probe
1:1/10:1 20/150MHz Probe
1:1 30MHz Probe
10:1 250MHz Probe
1:1/10:1 30/250MHz Probe
1:1/10:1 30/250MHz Probe
1:1/10:1 20/350MHz Probe
1:100 400MHz HV Probe
Price per
678-4007
678-4000
678-4004
678-4016
678-4010
678-4029
678-4035
678-4032
678-4022
unit
unit
unit
unit
unit
unit
unit
unit
unit
OM
Input Impedance
(MΩ)
1
10 (x10)
1 (x1); 10 (x10)
1
10 (x10)
1 (x1); 10 (x10)
1 (x1); 10 (x10)
1 (x1); 10 (x10)
50 (x100)
S$
Stock no.
678-4007
678-4000
678-4004
678-4016
678-4010
678-4029
678-4035
678-4032
678-4022
S$
S$
Stock no.
Replacement Cable PMS Probe
5.0 Standard Accessory kit
678-4044
678-4013
Price per
unit
unit
OM
S$
1+
1+
24·20
30·10
S$
S$
Elditest Compact Ergonomic
Oscilloscope Probes
Compact, ergonomically designed probes (non-modular)
for oscilloscopes
Integral compensation trimmer
Cable length 1.2m
Termination 50Ω BNC
Voltage category IEC1010-2-031 300V Cat 1
Test voltage 1150V
For accessories kit ( 1 screw driver, 1 BNC adaptor, 1
ground lead, 1 test clip, 1 needle ) see 207-4429
Note: This product is for use with instruments with a permanent earth connection
Supplied with: 1 replacement tip
1 coaxial adaptor
1 spring hook grabber
1 compensation trimming tool
1 earth lead with crocodile clip
Model
GE1501 GE2501 GE1511 GE1521
GE2511 GE2521
Attenuation
x1
x1
x10
x1/x10
x10
x1/x10
Bandwidth
30MHz 55MHz 150MHz 150MHz
250MHz 250MHz
Rise/Fall Time
11ns
6.4ns
2.3ns
2.3; 20ns
1.4ns
7.7; 1.4ns
Compensation Range
7777 pF 7777 pF 10-30pF 10-30pF
10-30pF 10-30pF
Input Capacitance
45pF
45pF
12pF
45; 12pF
12pF
45; 1245pF
Input Impedance
1MΩ
1MΩ
10MΩ 1(x1); 10(x10)MΩ 10MΩ 1(x1); 10(x10)MΩ
Stock no.
Bandwidth
Attenuation
Rise/Fall Time Input Capacitance Input Impedance
(MHz)
(ns)
(pF)
(MΩ)
150
x10
2.3
12
10
188-4786
150
x1/x10
2.3; 20
45; 12
1 (x1) ; 10 (x10)
163-7603
250
x10
1.4
12
10
163-7619
250
x1/x10
7.7; 1.4
45; 1245
1 (x1) ; 10 (x10)
163-7625
Description
GE-1511
GE-1521
GE-2511
GE-2521
Stock no.
188-4786
163-7603
163-7619
163-7625
Price per
unit
unit
unit
unit
OM
IEC1010-2-031 2000V CatI/ 1000V Cat II
4100V
Price per
OM
unit
S$
S$
S$
S$
S$
1+ 182·50
S$
Low capacity probe for measurements of high voltages
Provides optimum security for measurements of voltages up to
2500 V
Reinforced contact point and accessories for use in harsh
environments
Note: This product is for use with instruments with a permanent
earth connection
Max. voltage
Bandwidth
Load
Attenuation:
2.5 kV DC
DC - 250MHz
10 MΩ / 2.75 pF
x 100
Stock no.
156-8585
Wire length:
Rise/Fall Time
Compensation Range
EN6010 Rating
Price per
unit
3m
1.75ns
7-30pF
Yes
OM
S$
1+
820·00
Differential Oscilloscope Probes
Elditest GE8115 1500V Input
1+ 40·40
1+ 73·50
1+ 86·00
1+ 78·00
1+ 98·00
1+ 113·50
1+ 93·00
1+ 101·00
1+ 169·50
Accessories
Description
Voltage Category
Test Voltage
P5100 High Voltage Probe
CeramcoreTM Hybrid Probe
Coaxial Design
Interchangable spring tips 0.8 or 0.38 mm diam
Manu. Part No. Bandwidth Rise/Fall Compensation
Input
(MHz) Time (ns) Range (pF) Capacitance (pF)
PMS201A
25
14
*
37
PMS211A
150
1.4
10-35
12.5
PMS221A
20; 150
18; 2.4
15-40
78; 13
PMT201A
30
12
*
39.5
PMT211A
250
1.4
10-35
12.5
PMT221A
30; 250
12; 1.4
10-35
80; 13
PMT221A SPBL 30; 250
12; 1.4
10-35
80; 13
PMTG321A
20; 350
17.5; 1
10-35
105; 15
PHV1000
400
0.9
10-50
7.5
Description
x100
1.2m
S$
S$
S$
S$
1+ 74·00
1+ 88·00
1+ 56·50
1+ 101·50
1500V input voltage max
30MHz bandwidth max
Bi-colour power on LED indicates attenuation setting and flashes
to indicate battery low condition
Audible indication of input, over voltage, and operating modes
Auto power off option to conserve battery life
External d.c power supply socket
500hm BNC scope connection, input connections via two
800mm integral 4mm shrouded plug leads
Supplied with: Shrouded safety test prods, instruction manual
and 9V alkaline battery.
Accuracy
Common mode rejection ratio
Battery life (PP3 alkaline)
External supply (optional)
Output cable length
Safety
Dimensions (H x W x D)
Weight
3%
d.c. 70dB; a.c.>50dB (@ 1MHz)
approx. 15 hours
12V/35mA
500mm
IEC1010-2-031 Cat III 1500V to earth
157 x 60 x 226 mm
330 g (including battery)
Input Impedance
60MΩ /15pF Ω
Output Impedance
Attenuation (dB)
Maximum Differential Input
Voltage
50 Ω
x20 & x200
± 1500V d.c + a.c peak
V(ac)
Stock no.
296-3379
Price per
unit
Maximum Common Mode Input ± 1500V d.c + a.c peak V
Voltage
Output Voltage
± 1.5V (1MΩ) max.
Noise
1.5 mV
OM
S$
1+
810·00
S$
S$
S$
S$
Tektronix TDP0500, TDP1000
For high-speed switch mode power supply design; CAN/LIN bus
design; high-speed digital design; digital design and
characterization; manufacturing engineering test; research and
development.
±42 V (DC + pk AC) differential input voltage
18 dB CMRR (at 250 MHz 50X attenuation)
Selectable bandwidth limiting filters
DC reject
Connects to some Tektronix oscilloscopes using the TekVPIᓽ
probe interface
Easy access to scope-displayed probe menu for probe setup
control and operating status information
Auto-Zero – nulls output offset
Manu. Part No.
TDP0500
Stock no.
661-3292
Price per
unit
OM
S$
1+
6100·00
Accessories
Description
Accessory kit
Stock no.
207-4429
Price per
unit
OM
S$
1+
28·10
High Voltage Oscilloscope Probes
Elditest GE 3121 High Voltage
2kV, x100, Scope Probes
Compact probe for oscilloscopes
Low capacitance allowing high voltage measurements at
high bandwidths
Note: This product is for use with instruments with a
permanent earth connection
Supplied with: An earth lead with crocodile clip, a sprung hook grabber and a compensation
trimming tool.
Bandwidth
Rise/Fall Time
Compensation Range
d.c. - 150 MHz
1.8 ns
10 - 30 pF
Input Capacitance
Input Impedance
Input Voltage Max.
5 pF
50 MΩ
2kV a.c. or d.c.
www.rssingapore.com
New products available online every week
96
2349
www.nguyenxuong.com
ON-LINE
www.rssingapore.com
Oscilloscopes
Stock no.
Current Probes
661-3283
i3000s Flex 24 Flexible 3000A a.c. Current
Probe
Stock no.
Connecting cable length
Battery life
400 hours continuous
Output connection
Minimum load
100kΩ
Current Range
Output connection
Weight
Dimensions
Safety BNC connector
Accuracy
370g
Frequency Range
116 x 68.5 x 30mm (Electronics) Output Sensitivity
Measuring head cable
length
610mm (24in), double insulated Phase Shift
Price per
OM
S$
1+
846·00
2m (between head and
electronics)
0.5m cable terminated with
safety BNC connector
30; 300; 3000A AC, switch
selectable
+/-1 %
10Hz - 50k
100mV; 10mV; 1mV (AC
Coupled) V
<±1° (45 - 65Hz) ; ±10° @20kHz
S$
S$
i30s 30A High Resolution, High Bandwidth
Oscilloscope Current Probe
Stock no.
S645-1836
±1% of reading ±2mA
±1mA
d.c. to 100kHz
>100kΩ and ≤100pF
Better than 1μs
Price per
Max. conductor size
Battery life
Current Range
Output Sensitivity
Phase Shift
OM
S$
1+
1024·00
unit
19mm dia.
30 hours typical
0 to ±30A peak
100 mV/A V
< 2°, <1 kHz
S$
S$
Chauvin Arnoux E3 ac/dc
Probe
Current clamp specifically designed for use with
oscilloscopes
Clamp makes it possible to monitor current waveforms
directly and without breaking a connection
Note: This product requires a PP3 battery for operation
(stock number 450-3092).
Current range
Frequency range
Accuracy
Overange
Battery life
Stock no.
212-039
50 mA to 60 A
dc to 100kHz (-3dB)
±3%
to 100A
typ. 55hrs
Price per
OM
S$
1+
1070·00
unit
7160·00
1MΩ/100pF
<3μs
11.8mm
231x67x36mm
330g
S$
TCP0150 AC/DC current probe
OM
S$
1+
2750·00
unit
Frequency
Range
TCP312 current 100 MHz
probe
TCP404XL current 2 MHz
probe
Stock no.
Price
per
OM
S$
499-592
unit
1+
3020·00
499-598
unit
1+
6700·00
2350
S$
S$
P6243 Active Probe for SMDs
The P6243 Active FET probe is the high performance probing
solution for 500 MHz oscilloscopes.,Complete with a probe
only bandwidth of 1 GHz and will provide a 500 MHz system
bandwidth when used with Tektronix’ full line of 500 MHz
oscilloscopes.,In addition, it is powered by the TEKPROBE
BNC interface, eliminating the need for additional power
supplies and cables when used with TEKPROBE BNC
oscilloscopes.,Offers superior signal acquisition on surface
mount devices compared to the much higher capacitive loading of passive probes. The included
accessories and adapters allow for easy attachment to SMDs.
1 GHz Bandwidth (probe only)
≤pf Input Capacitance
1MΩ Input Resistance
Direct access to SMDs as small as 0.5mm pitch
Measures CMOS, BiCMOS, ECL, GaAs and TTL Logic
Low mass probe head/cable
Requires the TEKPROBE BNC interface to power the probe found on the TDS3000B series
oscilloscopes
Small compact probe head and versatile attachment accessories allow direct connection to the
device under test
Provides scope bandwidth at the probe tip for the TDS3000 series scope up to 1 GHz bandwidth
1.3 m
10X
1 GHz
<350 ps
=1 pF
1 MΩ
Linear Dynamic Range
DC Offset Range
Max Voltage (Non destruct) (DC+PkAC)
Propagation Delay
Compatible Oscilloscopes
±8 V
N/A
±15 V
5.3 ns ±200 ps
Tektronix TDS3000/3000B, TDS500/600/700
Kit Contents
S$
2 off 50 mil SureFoot
adapter
2 off 25 mil SureFoot
adapter
2 off 0.5 mm SureFoot
adapter
209-7860
1 off 3 in. Ground Lead
1 off Y Lead Adapters
10 off Solderable Probe Right Angle Square Pin
Tips
Adaptor
2 off 1 in. Ground Lead 100 Mil Square Pin Adaptor
2 off SMT KlipChipᓽ
adapter
1 off 6 in. Ground Lead Colour Coding Clips, 2 each 5
colours
Price per
OM
S$
1+
1850·00
unit
150 A
5 mA
www.rssingapore.com
OM = Order Multiple
S$
Active Oscilloscope Probes
Can be directly connected to DPO4000, MSO4000 and DPO7000
oscilloscopes using the TekVPI interface
Rise time: ≤17.5 ns
RMS max. current: 150 A
Max. inrush peak current: 500 A
Operating temperature: 0 → 50°C
96
S$
Bandwidth: 100 MHz (TCP 312), 2 MHz (TCP404XL)
Rise time: ≤3.5 ns (TCP 312), ≤175 ns (TCP404XL)
Signal delay: 17 ns (TCP 312), 103 ns (TCP404XL)
Max ACp-p: 60 A (TCP 312), 1414 A (TCP404XL)
Max direct current: 5 A → 1 A/V, 30 A → 10 A/V (TCP 312), 500
A → 1 A/mV (TCP404XL)
Current / div range: 1 A/V → 10 A/V (TCP 312), 1 A/mV
(TCP404XL)
Impedance @ 1 MΩ: 0.08 Ω (TCP 312), 0.1 mΩ (TCP404XL)
Max voltage on exposed wire: insulated cable (TCP 312), 600
VRMS CAT I & II 300 VRMS CAT III (TCP404XL)
Cable length: 1.5 m (TCP 312), 8 m (TCP404XL)
Stock no.
Current Range
Accuracy
S$
TCP 312 / 404XL current probe
Cable Length
Attenuation
Bandwidth(Probe Only)
Rise-time
Input C in pF
Input R in Ohms
Input impedance
Rise/Fall time
Max. dia. cable/bar
Dimensions
Weight
Price per
163-5310
Description
The i30 may be used in conjunction with bench and portable
oscilloscopes for accurate non-intrusive ac & dc current
measurement.,Applications include: inverters, switch mode
power supplies, industrial controllers, automotive leakage
currents and other applications requiring accurate isolated
current measurement.
Hall effect sensing of a.c. and d.c. current
Power LED warns of low battery by flashing
Zero adjust knob to accommodate offsets
The wide, flat frequency response means this probe exhibits a fast response when measuring
current pulses
2.0m flying lead terminated with 50Ω BNC plugs
Designed to meet EN61010-1, EN61010-2-032 installation CAT III 300V
Withstands overloads to 500A
Supplied with: Alkaline PP3 battery, 4mm shrouded plug adaptor and operators manual.
Overall d.c. accuracy
Resolution
Frequency response (-0.5dB)
Output (load) impedance
Response time
1+
unit
S$
Current range
5A
Admissible peak current 250A
Frequency range 120 Hz to 60 MHz Capacity of jaws
Ø3.81mm
Response Time 5.8ns
Cable length
1.5m
Maximum Current 15A
1° (45Hz to 65Hz) batteries
unit
S$
Oscilloscope probe for analysing current of signals
without opening the circuit
No electrical connection required
Excellent low frequency characteristics
Passive termination equipped with a 2mA/mV and 10mA/
mV range switch
Phase error
Stock no.
OM
Tektronix P6021
Suitable for use with oscilloscopes, recorders and data
loggers
a.c. coupled output (no d.c. offset)
Voltage output of 3V full scale for each range
Fits around conductors up to 160mm diameter
Extended battery life and external power supply input
Meets BS EN61010 – 1 Cat III 600V
Extended working temperature range -20°C to +90°C
Conforms to EN61010-1 CAT III 600V
Contact RS for calibration requirements
Supplied with: 2 x AA alkaline batteries, BNC to 4mm plug
adaptor and operator’s manual.
S645-3668
Price per
S$
S$
www.nguyenxuong.com
ORDERLINE
65 6865 3433
Oscilloscopes
Tektronix TAP1500
≥1.5 GHz probe bandwidth
<267 ps rise time
≤1 pF input capacitance
1 MΩ input resistance
–8 V to +8 V input dynamic range
–10 V to +10 V DC input offset range
Small compact head for probing small geometry circuit
elements
DUT attachment accessories enable connection to SMDs
as small as 0.5 mm Pitch
Robust design for reliability
Connects to some Tektronix oscilloscopes using the TekVPIᓽ probe interface
Provides automatic units scaling and readout on the oscilloscope display
Easy access to oscilloscope probe menu display for probe status/diagnostic information, and to
control probe DC offset
Note: TAP1500 (661-3286) includes individual probe case, TAP1500X2 (697-8808) does not
Supplied with: Ground leads, adaptors, colour-coding clips, solderable probe tips, test tips, user
manual, nylon carrying case
Manu. Part No.
Stock no.
TAP1500
661-3286
Price per
unit
OM
S$
1+
4110·00
S$
S$
High-voltage active differential
probe
The probe can convert floating signals into low-voltage
signals referenced to earth
Bandwidth: 50 MHz
RMS differential voltage: 4400 V
Peak differential voltage: 5600 V
Attenuation: 100X / 1000X
CMRR @ 60 Hz / 1 MHz: 80 dB / 50 dB
R input: 8 MΩ
C input: 7 pF
Power supply: TekProbe Power Supply
Compatible with: TDS400 / 500 / 600 / 700, TDS3000B /
5000B / 6000B / 7000B, CA7000B / 11000
Conforms to: UL3111-1 / CSA1010.1 / CSA1010.2.031 /
IEC61010-2-031 / EN61010-2-031
Stock no.
499-659
Price per
unit
Low Level Signal Amplifier
Tektronix ADA400A 1 MHz
Differential Preamplifier
The ADA400A Active Differential Preamplifier allows direct
oscilloscope measurements of very low amplitude voltages and
signals which are not ground referenced. The high impedance of
both inputs eliminates the need to add additional ground points
in the DUT, thereby avoiding circulating currents which disturb
the measurement or the circuit.,The high gain and extremely high
common mode rejection provide usable measurements of
voltages as low as 5&mu;V, even in high noise environments.
Selectable bandwidth limiting reduces normal mode noise from
digital logic, switch mode power supplies and line frequency
sources. Adjustable differential offset allows the user to null out
transducer bridge bias and galvanic potential from the test set-up.
An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate
measurements of signals with high source impedance. It is specifically designed to operate on
Tektronix oscilloscopes with TEKPROBEᓼ interface
10μV/div Sensitivity
Low-pass filter: 100Hz, 3kHz, 100Hz or Full (1 MHz)
Typically 100 dB CMRR DC to 10 kHz
Selectable Gain: 100, 10, 1 or 0.1
Accurately measures signal as small as 5uV
Integral Probe Power with TEKPROBEᓽBNC
Gain
CM Range
Differential Range*1
MAX Offset
100
±10 V
0.1 V
±1.0 V
10
±10 V
1V
±1.0 V
1
±40 V
10 V
±40 V
0.1
±40 V
80 V
±40 V
Compatible Oscilloscopes TDS400/500/600/700/3000/3000/5000
Stock no.
349-8214
Price per
unit
OM
S$
1+
3170·00
S$
S$
S$
S$
Current probe amplifier
OM
S$
1+
4920·00
S$
S$
Suitable for the TCP404XL current measurement system
BNC connector
TekProbe interface
Certified calibration
Instructions and manual
Stock no.
499-627
Price per
unit
OM
S$
1+
4050·00
www.rssingapore.com
96
Many more leading brands from over 2,500 suppliers available online
2351

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project