Erbauer | ERB238MSW | Instruction manual | Erbauer ERB238MSW Instruction manual

Original Instructions
Patent Pending 1008829.2
Read instructions fully before operating this tool
ERB238MSW
(SKU NO 33776 - J1X-KZ13-2555)
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Congratulations on your purchase of a quality power tool from Erbauer Ltd.
This product should give you reliable service for your peace of mind this power
tool does carry a 24-month guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
GUARANTEE
This
product carries an Erbauer Ltd guarantee of 24 months. If your
for a full refund or we will repair or replace the goods if you prefer. When repair
is not practical or identical goods are not available, alternative goods of similar
a partial or full refund depending on the time period since purchase.
!
"
-Fair wear and tear
-Misuse or abuse
-Lack of routine maintenance
-Failure of consumable items (such as batteries)
-Accidental damage
-Cosmetic damage
-Failure to follow manufacturer’s guidelines
-Loss of use of the goods
-Repairs attempted by anyone, unless authorised by Erbauer Ltd.
This guarantee does not affect your statutory rights. This guarantee is only valid in the
UK.
For further technical advice and spare parts, please contact your retailer your Erbauer model number.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
SAFETY INSTRUCTIONS
WARNING! When using electric tools basic safety precautions should always
#
#
$
including the following.
Read all these instructions before attempting to operate this product and save these
instructions.
SAVE THESE INSTRUCTIONS
The term “power tool” in the warning refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1 Keep work area clear
%&
$
2 Consider work area environment
%'
!
- Do not use tools in damp or wet locations.
- Keep work area well lit.
%'
*
3 Guard against electric shock
- Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators,
ranges, refrigerators).
4 Keep other persons away
- Do not let persons, especially children, not involved in the work touch the tool or
!
#
#
5 Store idle tools
- When not in use, tools should be stored in a dry locked-up place, out of reach of
children.
6 Do not force the tool
%
$
7 Use the right tool
%'
$
%'
+
!
to cut tree limbs or logs.
8 Dress properly
%'
$
- Non-skid footwear is recommended when working outdoors.
- Wear protective hair covering to contain long hair.
9 Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations create dust.
10 Connect dust extraction equipment
%
!
11 Do not abuse the cord
- Never yank the cord to disconnect it from the socket. Keep the cord away from
heat, oil and sharp edges.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
12 Secure work
- Where possible use clamps or a vice to hold the work. It is safer than using your hand.
13 Do not overreach
- Keep proper footing and balance at all times.
14 Maintain tools with care
- Keep cutting tools sharp and clean for better and safer performance.
- Follow instruction for lubricating and changing accessories.
- Inspect tool cords periodically and if damaged have them repaired by an
authorized service facility.
%
!
- Keep handles dry, clean and free from oil and grease.
15 Disconnect tools
- When not in use, before servicing and when changing accessories such as blades,
bits and cutters, disconnect tools from the power supply.
16 Remove adjusting keys and wrenches
%/
#
#
$
from the tool before turning it on.
17 Avoid unintentional starting
- Ensure switch is in “off” position when plugging in.
18 Use outdoor extension leads
%0
!
and so marked.
19 Stay alert
- Watch what you are doing, use common sense and do not operate the tool when
you are tired.
20 Check damaged parts
- Before further use of tool, it should be carefully checked to determine that it will
operate properly and perform its intended function.
- Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation.
- A guard or other part that is damaged should be properly repaired or replaced by
an authorised service centre unless otherwise indicated in this instruction manual.
- Have defective switches replaced by an authorised service centre.
- Do not use the tool if the switch does not turn it on and off.
21 Warning
- The use of any accessory or attachment other than one recommended in this
#
$
+DYH\RXUWRROUHSDLUHGE\DTXDOLÀHGSHUVRQ
- This electric tool complies with the relevant safety rules. Repairs should only be
in considerable danger to the user.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
HEALTH ADVICE
Warning! When drilling, sanding, sawing or grinding, dust particles will be
produced. In some instances, depending on the materials you are working
with, this dust can be particularly harmful to you (e.g. lead from old gloss paint).You
are advised to consider the risks associated with the materials you are working with
#
!
8"
-Work in a well-ventilated area.
%0#
#
SAFETY INSTRUCTIONS FOR ALL SAWS
a. DANGER: Keep hands away from cutting area and the blade. Keep your second
hand on the handle, or motor housing. If both hands are holding the saw, they
cannot be cut by the blade.
b. Do not reach underneath the workpiece. The guard cannot protect you from the
blade below the workpiece.
c. Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth
of the blade teeth should be visible below the workpiece.
d. Never hold piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform. It is important to support the work properly to
9
!
e. Hold power tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a
:
;
#
!
:
;#
operator.
f. When ripping always use a rip fence or straight edge guide. This improves the
accuracy of cut and reduces the chance of blade binding.
g. Always use blades with correct size and shape (diamond versus round) of
arbor holes. Blades that do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
h. Never use damaged or incorrect blade washers or bolt. The blade washers and
bolt were specially designed for your saw, for optimum performance and safety of
operation.
Further safety instructions for all saws
&
###"
<###
an uncontrolled saw to lift up and out of the workpiece toward the operator;
<
#
and the motor reaction drives the unit rapidly back toward the operator;
<
#
the blade can dig into the top surface of the wood causing the blade to climb out of
#
$#
Kickback is the result of saw misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
D0DLQWDLQDÀUPJULSZLWKERWKKDQGVRQWKHVDZDQGSRVLWLRQ\RXUDUPVWRUHVLVW
kickback forces. Position your body to either side of the blade, but not in line with
the blade. ?##
$####
be controlled by the operator, if proper precautions are taken.
b. When blade is binding, or when interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback may occur. Investigate and take
corrective actions to eliminate the cause of blade binding.
c. When restarting a saw in the workpiece, centre the saw blade in the kerf and
check that saw teeth are not engaged into the material. If saw blade is binding, it
may walk up or kickback from the workpiece as the saw is restarted.
d. Support large panels to minimise the risk of blade pinching and kickback. Large
panels tend to sag under their own weight. Supports must be placed under the panel
on both sides, near the line of cut and near the edge of the panel.
e. Do not use dull or damaged blades. Unsharpened or improperly set blades
#
!
###
f. Blade depth and bevel adjusting locking levers must be tight and secure before
making cut. $
kickback.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR MITRE SAW
Warning: Be sure to read and understand all instructions. Failure to
IROORZDOOLQVWUXFWLRQVOLVWHGEHORZPD\UHVXOWLQHOHFWULFVKRFNÀUHDQG
or serious personal injury.
1. Know your power tool. Read operator’s manual carefully. Learn the applications
DQGOLPLWDWLRQVDVZHOODVWKHVSHFLÀFSRWHQWLDOKD]DUGVUHODWHGWRWKLVWRRO
2. Always wear safety glasses or eye shields when using this mitre saw. Everyday
eyeglasses have only impact-resistant lenses; they are not safety glasses.
3. Always protect your lungs. Wear a face mask or dust mask if the operation is dusty.
Always use dust extraction equipment to minimise dust.
4. Always protect your hearing. Wear hearing protection during extended periods
of operation.
5. Always inspect the tool cords periodically and if damaged have them repaired.
Always be aware of the cord location.
6. Always check for damaged parts. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine if it will
operate properly and perform its intended function. Check for misalignment or
binding of moving parts, breakage of parts, and any other condition that may
affect the tool’s operation. A guard or other part that is damaged should be
SURSHUO\UHSDLUHGRUUHSODFHGDWDTXDOLÀHGVHUYLFHFHQWUH
7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from
the socket. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
8. Always make sure that your extension cord is in good condition. When using
an extension cord be sure to use one that is heavy enough to carry the current
that your tool will draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and overheating.
9. Always inspect and remove all nails from lumber before sawing.
'RQRWXVHWKHWRROZKLOHWLUHGRUXQGHUWKHLQÁXHQFHRIGUXJVDOFRKRORUDQ\
medication/
#
#
$
11. Save these instructions. Refer to them frequently and use them to instruct
others who may use this tool. If someone borrows this tool, make sure they have
these instructions also.
:KHQWKHFRUUHFWEODGHWRFXWWKHPDWHULDOKDVEHHQÀWWHGWKLVVDZLV
recommended for cutting wood and plastic only.
13. Do not use saw blades with High Speed Steel (HSS) or damaged or deformed
blades.
14. Replace the table insert when worn.
15. Use only saw blades recommended by the manufacturer and which have the
exact bore and diameter required for this machine.
16. Connect your mitre saw to a dust collecting device (I. D.Ø32mm) when sawing.
17. Select saw blades in relation to the material to be cut.
18. Check the maximum depth of cut.
19. When sawing long work pieces, always use extra support to provide better
support, and use clamps or other clamping devices.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
20. The operator is adequately trained in the use, adjustment and operation and
operation of the machine.
21. Provide for adequate room lighting at your workplace or for adequate lighting
of the immediate work area.
:KHQÀWWHGZLWKODVHUQRH[FKDQJHZLWKGLIIHUHQWW\SHRIODVHULVSHUPLWWHG
Repairs shall only be carried out by the laser manufacturer or an authorised
agent.
23. Refrain from removing any cut-offs or other parts of the workpiece from
the cutting area whilst the machine is running and the saw head is not the rest
position.
24. Never stand on this tool. Serious injuries could occur when this tool tips over
or when coming in contact with the saw blade.
25. Only use the saw with guards in good working order and properly maintained,
and in position.
.HHSWKHÁRRUDUHDIUHHRIORRVHPDWHULDOHJFKLSVDQGFXWRIIV
27. Ensure the speed marked on the saw blade is at least equal to the speed
marked on the saw.
28. Warning. Not replace the laser with a different type. Instruction that repairs
shall only be carried out by the laser manufacturer or an authorised agent.
WARNING:
$
thrown into your eyes, which can result in severe eye damage. Before
beginning power tool operation, always wear safety goggles or safety glasses with
side shield and a full face shield when needed.
WARNING: If any parts are missing, do not operate your mitre saw until the
missing parts are replaced. Failure to follow this rule could result in serious
$
Caution: Do not let familiarity with your mitre saw make you careless. Remember
$
Double insulation:
!
electrically insulated from the mains power supply. This is done by placing insulation
barriers between the electrical and mechanical components making it unnecessary
for the tool to be earthed.
Important note
Be sure the supply is the same as the voltage given on the rating plate. The tool is
%
@
#
$
SAFETY RULES FOR LASER LIGHT
G
&!P0
QV[
wavelength.
These lasers do not normally present an optical hazard, although staring at the
*
WARNING:'
\9
!
"
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
- The laser shall be used and maintained in accordance with the manufacturer’s
instructions.
%]
$
#
- The laser beam shall not be deliberately aimed at personnel and shall be prevented
[V
%\
#
*
^
*
#
*
direct the beam back at the operator.
- Do not change the laser light assembly with a different type. Repairs must be
carried out by the laser manufacturer or an authorised agent.
SPECIFIC SAFETY RULES & SYMBOLS
WARNING!
Do not operate machine if warning and / or instruction labels are missing or damaged.
Symbol
Description
V
Volts
A
Amperes
Hz
Hertz
Min-1
Speed
~
Alternating Current
no
No Load Speed
Double Insulated
Wear Safety Goggles
Wear Ear Protection
Wear Dust Mask
Read Instruction Manual
Laser Warning Symbol
Conforms to relevant
safety standards
General Warning
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
KNOW YOUR SLIDING MITRE SAW
3
1
2
5
14
4
8
13
6
12
10
11
9
7
Fig 1
1. DUST BAG
2. UPPER BLADE GUARD
3. CUTTING HANDLE
4. LOWER BLADE GUARD
5. BLADE
6. TABLE INSERT
7. MITRE HANDLE
8. LASER GUIDE
9. BASE
10. TURNTABLE
11. LEFT EXTENSION TABLE
12. FENCE
13. HOLD-DOWN CLAMP
14. SLIDE CARRIAGE LOCK KNOB
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
21
22
19
16
15
17
23
18
20
Fig 2
15. CARRYING HANDLE
16. SLIDE CARRIAGE
17. BEVEL LOCK HANDLE
18. RIGHT EXTENSION TABLE
19. MOTOR
20. POSITIVE STOP LOCKING LEVER
21. LOWER BLADE GUARD LOCK LEVER
/$6(5212))6:,7&+
23. ADJUSTABLE CUTTING STOP
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
TECHNICAL DATA
q"x[q{V[|9
}
"PQ[[0
]%
"x[[-1
"II
]
"P#
^
"V+x[^
"€V

"[‚PV‚V‚xPQ‚V‚ƒ

"[‚V‚ƒ
^
"[‚V‚ƒ
!"
&„[‚^
![‚
…†P!x[[

„[‚^
!V‚
…†P!P[
^
„V‚^
![‚
…V[!x[[
&„V‚^
!V‚
…V[!P[
NOISE AND VIBRATION DATA
‡
ƒ}\"€Q^„\…„?ˆx^„\……
‡
ƒ0\"P[‰Q^„\…„?ˆx^„\……
q
"‰VG2„?ˆVG2)
- The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another.
- The declared vibration total value may also be used in a preliminary assessment of
!
WARNING: The vibration emission during actual use of the power tool can differ
from the declared total value depending on the ways in which the tool is used; and
of the need to identify safety measures to protect the operator that are based on an
!
„#
the operating cycle such as the times when the tool is switched off and when it is
running idle in addition to the trigger time).
ACCESSORIES
Allen Key 1 pc
Dust Bag 1 pc
Hold-Down Clamp 1 pc
Mitre Handle 1 pc
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help
$
results to enable users to make informed decisions as to the period of time a power
tool can be used safely on a daily basis and the choice of tool.Further Advice can be
found at www.hse.gov.uk
q
„!
…
Š]QP[€
+‡ˆŠ]QP[€%P[[€
Test prodcure GS mark.
q
ˆ‰VG‹
Œ
?ˆVG‹
The declared vibration emission value should be used as a minimum level should be used with
the current guidance on vibration.
& |‡Š has further information.
The declared vibration emission been measured in accordance with a standardised test stated
above and may be used to compare one tool with another.
!
Warning: The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used
!
"%
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome
if its use is not adequately managed
Warning: identify safety measures to protect the operator that are based on an
!
„#
of the operating cycle such as the times when the tool is switched off and when it is
running idle in addition to the trigger time).Note The use of other tools will reduce the
#
|
!
#
ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate)
\
P[&
Plan your work schedule to spread any high vibration tool use across a number of days.
Health Surveillance
All employees should be part of an employer’s health surveillance scheme to help identity
any vibration related diseases at an early stage, prevent disease progression and
help employees stay in work.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ASSEMBLY INSTRUCTIONS
1
1. Installing the mitre handle
1) Thread the mitre handle (1) into the hole
„‡
x…
Fig 3
2. Unlocking the slide carriage
After removing the saw from the carton,
loosen the slide carriage lock knob (1). When
transporting or storing the mitre saw, the slide
carriage should always be locked in position.
The slide carriage lock knob (1) is located on the
„‡
…
1
Fig 4
3. Raising the Cutting Head
1) Push down slightly on the switch handle (1)
and the lock lever (2).
2) Pull out the stop latch knob (3).
3) Allow the cutting head to rise to the up
„‡
V…
2
1
3
Fig 5
Warning:$
this mitre saw to the power source until
$
have read and understood this Operator’s Manual.
Warning:$
to the saw, transport and store the
mitre saw with the cutting head locked in the
down position. Never use the stop latch to hold
the cutting head in a down position for cutting
operations.
Locking
When transporting or storing the mitre saw, the
cutting head should always be locked in the down
position.
1) Push the lock lever (2) and cutting head down
to its lowest position.
2) Push the stop latch knob (3) into the locking
hole.
IMPORTANT
To avoid damage, never carry the mitre saw by
the cutting arm or the mitre handle. ALWAYS use
both designated carrying handles together.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
4. Installing the dust bag
P…‡
9
„…
dust bag (1).
2) Place the dust bag neck opening around the
!„x…
„‡
Q…
5. Installing the hold-down clamp
1) Loosen the lock knob (1) from the rear side
„…„‡
‰…
2) Place the hold-down clamp assembly (3) in
„…„‡
†…
x…
##„P…„‡
‰…
1
2
3
Fig 6
3
Warning: When using stop block on
the right side, hold-down clamp must
also be in right side. Using hold-down clamp
on the left side during this operation can cause
###
$
2
1
Fig 7
4
4
/†
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
6. Mounting the mitre saw
1
2
3
4
5
6
8
7
/€
P…|
!
2) Spring washer
3) Flat washer
4) Mitre saw base
5) Workbench
6) Flat washer
7) Spring washer
†…|
!
€…ƒ#
/P[
9
Warning:$
!
"
‘'
#
and lock the cutting head in the lower position
using the stop latch.
‘ƒ#
the slide carriage lock knob.
‘#$
designated carrying handles located on the
top of the machine. When lifting, bend at your
knees, not from your back.
‘]
or by the switch handle. Carrying the tool by
the power cord could cause damage to the
insulation or the wire connections resulting in
#
‘$*
visitors to stand near the saw during any cutting
operation.
‘‡
#
‘^
Mounting instructions
1) For stationary use, place the saw in the desired
location, directly on a workbench where there
is room for handling and proper support of the
workpiece. The base of the saw has four mounting
holes. Bolt the base of the mitre saw (1) to the
work surface (5),using the fastening method as
/€
2) For portable use, place the saw on a
[„!…#
^
base of the mitre saw securely to the plywood
using the mounting holes on the base. Use
G-clamps to clamp this mounting board to a stable
#
#
„‡
P[…
Note: Mounting hardware is not included with this
tool. Bolts, nuts, washers and screws must be
purchased separately.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
7. Removing and installing the blade
Warning:
‘'
V
diameter.
‘$
#
sure the switch is in the OFF position and the
plug is not connected to the power source
socket.
‘/
PxP0
operator considers wearing protective gloves
when handling or installing the blade.
Removing blade
1) Unplug the saw from the socket.
2) The slide carriage should be locked in
position by tightening the slide carriage lock
#„P…„‡
PP…
3) Allow the cutting head to rise to the upright
„‡
PP…
4) Release the lower blade guard by operating
the blade guard handle, and rotate the guard
into its upper position.
V…ƒ
#„P…„‡
P…
6) Hold the guard in position with your thumb
#
„‡
Px…@
sized allen key inserted into the arbor bolt (See
P… until positive location is felt.
‰…?
#
undo the arbor bolt with the allen key by
turning it in a clockwise direction.
†…@
*
machine.
€…0
*
gently ease the blade from the spindle and
remove downwards and away from the cutting
head.
Note: Pay attention to the pieces removed,
noting their position and direction they face.
Wipe the blade collars clean of any sawdust
before installing a new blade.
1
Fig 11
1
Fig 12
Fig 13
Fig 14
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
8. Installing Blade
Unplug the mitre saw before changing/installing
the blade.
Note:Š
!
the correct size for this machine and the
!
V
Fig 15
1) Rotate and hold lower blade guard in its
upper position as already described.
…V
x[
making sure the rotation arrow on the blade
matches the clockwise rotation arrow on the upper
guard and the blade teeth are pointing downward.
3) Place the outer blade collar against the blade
and on the arbor. Thread the arbor bolt onto the
#
„‡
PV…
IMPORTANT
#
*
*
4) Place the allen key into the arbor bolt.
5) Press the arbor lock, holding gently while
turning the blade counterclockwise. When arbor
#
„‡
P…
Note: Do not press arbor lock when blade is
moving.
Warning: Be sure that the arbor lock
is released so that the blade turns
freely. Lower the blade into the lower table and
check for any contact with the base or the mitre
table by spinning the blade manually. Make sure
the collars are clean and properly arranged.
Check that the lower blade guard is functioning
correctly and does not bind or stick.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
9. Aligning the laser beam
Laser ON/OFF Switch
Warning: For your own safety, never
connect the plug to power source
#
$
complete and you have read and understood
the safety and operational instructions. The
laser beam must always be correctly aligned
with the blade to ensure straight, even cutting.
8
ƒ
cutting guide using a Class II laser beam.
The laser beam will enable the operator to
preview the saw blade path on the stock to be
cut before starting the saw. This laser guide
is powered by the transformed alternating
current supply directly through the power
lead. The saw must be connected to the
power source and the laser on/off switch must
be turned on for the laser line to show.
„‡
PQ…
Fig 16
Warning:
AVOID DIRECT EYE CONTACT
Laser radiated when laser guide is turned on.
Avoid direct eye contact. Always unplug the
mitre saw from power source before making
$
ƒ
0ƒ
"!’P0
0
"Qx[%Q‰[Š]Q[†V%PG
\P"[[‰ƒ
beam Class 2 Laser Product Puissance.
Note:\
$
of this machine have been completed at the
factory. Due to normal wear and use, some
$
A. Check Laser Beam Alignment
P…#€[‚
to serve as a “pattern line” to test laser
alignment. Lay the board on the mitre table.
2) Plug saw into socket and turn on the laser
beam and line it up with the pattern line.
3) Lower saw blade to pattern line and
*
$
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
2
G$
are provided. Two (1,2) are positioned on the LH
side of the laser housing, and one (3) on the RH
side of the laser housing. These screws gently
hold the laser module in place and on alignment
by bearing on the laser modules casing. It is
$
on the laser module casing is maintained as
closely as possible to the factory setting. Do not
over tighten any one screw – damage to the laser
„‡
P‰”P†…
1
Fig 17
3
/P†
B Adjusting the Angle of the Laser Guide
1) Loosen the single screw on the RH side of
the laser housing ½ a turn.
2)Turn the laser element in the desired direction
$
x…@
$
C Aligning the Laser Beam
P…Œ
$
ƒ|
of the laser housing.
…\$
achieved.
Warning: Use only the correct sized
#
$
screws. Turn one screw at a time and only ¼
turn in either direction before checking laser
alignment. Maintain as far as possible the
original factory pressure setting that these
!
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ADJUSTMENT INSTRUCTIONS
1. Bevel stop adjustment
Warning:$ accidental start, make sure the switch is
in the OFF position and the plug is not connected
to the power source socket.
2. 90° (0°) Bevel adjustment
1) Loosen bevel lock handle (1) and rotate the
cutting arm completely to the right until it stops
against the vertical stop. Tighten the bevel lock
handle.
…}
„…
table with the ruler against the table and the
x…
€[°„[°…
table (5), loosen the bevel lock handle (1), tilt the
cutting head to the left, loosen the locknut (4) on the
$
„x…
#
$
#
„x…
out to increase or decrease the bevel angle.
…
#
€[°
„[°) bevel and recheck for alignment.
V…@
P
$
is needed.
6) Tighten bevel lock handle (1) and locknut (4)
when alignment is achieved. „‡
P€…
4
3
1
2
5
/P€
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
3. Bevel pointer adjustment
P…0
!€[°„[°) to the
table, loosen the bevel indicator screw (1) using
a # 2 Phillips screwdriver.
…\$
„…
:[°” mark on
the bevel scale and retighten the screw. (See
[…
1
2
/[
2
3
2
3
1
Fig 21
4. Bevel adjustment 45°
1) Loosen the bevel lock handle (1) and tilt the
cutting head completely to the left.
…Œ
#
the blade angle is 45° to the table.
3) If the blade is not at 45° to the mitre table,
tilt the cutting arm to the right, loosen the
#„…
$
„x…
#
$
(3) depth in or out to increase or decrease the
bevel angle.
4) Tilt the cutting arm to the left to 45° bevel
and recheck for alignment.
5) Repeat steps 1 through 4 until the blade is at
V‚
6) Tighten bevel lock handle (1) and locknut (2)
when alignment is achieved. „‡
P…
3
1
2
3
Fig 22
4
5. Bevel Setting for Crown Moulding
xx€° for
cutting crown mouldings.
1) Twist and deploy sprung-loaded crown
moulding pin (2).
2) Loosen the bevel lock handle (1) and rotate
!
„…
#„‡
…
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
6. Bevel adjustment 33.9o
xx€° settings can be checked
$
\
xx€°
P…‡
xx€‚
the crown moulding pin. Check the angle of
the blade against the machine table using the
„‡
x…
…$
#
(3) to the relevant socket headed stop screw.
\$
angle is achieved. Retighten the locknut. (See
…
7. Mitre angle adjustment
The sliding compound mitre saw scale can be
[‚
V‚
[‚V‚
mitre saw table has nine of the most common
[‚PV‚
V‚xPQ‚V‚
#
and accurately. Follow the process below for
#
$
1) Unlock the mitre table by turning the mitre
handle (1) counterclockwise.
2) Move the turntable while lifting up on
the positive stop locking lever (2) to align
the indicator (3) to the desired degree
measurement.
3) If the desired angle is one of the nine positive
stops, release the positive stop locking lever,
making sure the lever snaps into position, and
then secure by tightening the mitre handle.
4) If the mitre angle desired is not one of the
nine positive stops, simply lock the mitre table
into position by turning the mitre handle in the
#
„‡
…
Fig 23
4
3
1
2
Fig 24
8. Mitre scale indicator adjustment
P…
[‚
2) Loosen the screw (4) that holds the indicator
with a Phillips screwdriver.
x…\$
„x…
[‚#
„‡
…
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
1
2
1
3
9. Adjusting fence squareness
1) Loosen the four fence locking bolts (1).
2) Lower the cutting arm and lock in position.
x…Œ
„x…
against the blade and the ruler against the
fence(2) as shown.
…\$
€[‚
the four fence locking bolts. „‡
V…
Caution: If the saw has not been used recently,
#
$
5) After fence has been aligned, using a scrap piece
#
#–

@
$
Fig 25
1
3
Fig 26
2
10. Setting cutting depth
The depth of cut can be preset for even and
repetitive shallow cuts.
P…\$
„‡
&Œ]—
HEAD section) until the teeth of the blade are at
the desired depth.
2) While holding the upper arm in that position,
turn the stop knob (1) until it touches the stop
plate (2).
3) Recheck the blade depth by moving the
cutting head front to back through the full
motion of a typical cut along the control arm.
„‡
Q…
11. Adjusting cutting depth
!
was set at the factory. Check to see that the
!
QxV
the table insert, and does not touch the control
arm throat or any part of the base or table. If the
!
$"
1) Loosen the depth control screw locknut (3).
…}
!
the depth control screw.
x…\$
!
QxV
4) Recheck the blade depth by moving the
cutting head front to back through the full
motion of a cut along the control arm. If the
blade touches the inside of the control arm,
$
#
„‡
Q…
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
OPERATION INSTRUCTIONS
1
Warning: Before using your mitre
saw be sure to read the instruction
manual carefully.
Operating instructions
1. Know your mitre saw
Read and understand the Operator’s Manual and
!
ƒ
and limitations as well as the potential hazards
$
accidental contact with moving parts, do not lay
out, assemble or set up work on the mitre saw.
2. Electrical connection
Your mitre saw has a precision-built electric
x[q
V[|9}
„
…
Do not operate on direct current (DC). This large
voltage drop will cause a loss of power that will
overheat the motor. If your mitre saw does not
operate when plugged into an socket, have a
professional electrician check the power supply.
No-Hands Zone
Fig 27
Warning: Avoid accidental starting.
Make sure the switch is in the
OFF position before plugging the mitre
saw into a power socket.
3. Body and Hand position
Warning: Never place hands near the
cutting area. Proper positioning of
your body and hands when operating the
mitre saw will make cutting easier and safer.
Keep children away. Keep all visitors at a
safe distance from the mitre saw. Make sure
bystanders are clear of the saw and workpiece.
'
$
safer at its designed rate.
Starting a cut:
‘}
P€[V
the blade – out of the “no-hands zone” (1).
(See Fig 27)
‘&#
prevent movement toward the blade.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
‘0
˜//
blade down to the workpiece to see the cutting
path of the blade
‘‡
9
‘ƒ
#
downward motion.
Finishing a cut:
‘|
‘@
parts to stop before moving your hands and
raising the cutting arm.
Before releasing jammed material:
‘@
‘0
‘Œ
2
1
/†
1
/€
4. Basic saw operations
Warning: For your convenience, your
saw has a blade brake. The brake is
not a safety device. Never rely on it to replace
the proper use of the guard on your saw. If
!
†
seconds, wait for the blade to stop, unplug the
saw and contact customer service.
To turn saw on
}
#
„P…
9
trigger switch (2) to turn the mitre saw ON.
Release the trigger switch to turn the saw OFF.
„‡
†…
5. Sliding carriage system
1) For chop cutting operations on small
workpieces, slide the cutting head assembly
completely toward the rear of the unit and
tighten the carriage lock knob (1).
…
x[[
carriage lock knob must be loosened to allow
„‡
€…
Before leaving the saw
‘]
power OFF. Wait for all moving parts to stop.
‘#
#ƒ#
Disconnect master switches. Store tool away
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Warning:$
materials being thrown, always
unplug the saw to avoid accidental starting,
and remove small pieces of material from the
table cavity.
6. Mitre cut
P…0
#
mitre table by turning the mitre handle (1)
counterclockwise.
2) While holding the mitre handle, lift up on the
positive stop locking lever (2).
3) Rotate the mitre table to the right or left
with the mitre handle.
4) When the table is in the desired position,
as shown on the mitre scale (3), release the
positive stop locking lever and tighten the
mitre handle. The table is now locked at the
desired angle. Positive stops are provided at
[‚PV‚V‚xPQ‚V‚„‡
x[…
1
3
2
/x[
IMPORTANT
Always tighten the mitre table lock handle
before performing every cutting operation.
7. Bevel cut
P…0
bevel lock handle (1) by turning it clockwise.
2) Tilt the cutting head to the desired angle, as
shown on the bevel scale (2)
3) The blade can be positioned at any angle,
€[°„[° on the scale) to a
V‚
#
(1) to lock the cutting head in position.
}
[°xx€° and
45°„‡
xP…
Note: When cutting at 45 degrees, ensure
guard does not catch on work or machine
base plate.
2
1
Fig 31
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
8. Compound cut
A compound cut is the combination of a mitre
and a bevel cut simultaneously.
1) Loosen the bevel lock handle (1) and position
the cutting head at the desired bevel position.
Lock the bevel lock handle.
2) Loosen the mitre handle (2). Press down the
positive stop locking lever (3) and position the
table at the desired angle. Release the positive
stop locking lever and lock the mitre handle.
„‡
x…
1
2
3
Fig 32
9. Slide cutting wide boards up to 300mm wide
Warning:
To avoid injury:
‘]
spinning blade toward you during the cut. The
blade may try to climb up on the top of the
workpiece, causing the cutting assembly and
spinning blade to kick back, forcefully. The
cutting head assembly should be drawn back
completely then pushed forward when sawing.
‘ƒ
This will help reduce the risk of a thrown
workpiece.
2
3
1
4
Fig 33
To slide cut wide boards
1) Unlock the carriage lock handle (1) and allow
the cutting head assembly to move freely.
2) Set both the desired bevel angle and/or the
mitre angle and lock into position.
3) Use a hold down clamp to secure the
workpiece.
4) Grasp the switch handle (2) and pull the
carriage (3) forward until the centre of the saw
blade is over the front of the workpiece (4).
5) Engage the trigger to turn the saw on.
6) When the saw reaches full speed, push the
switch handle down, slowly, cutting through the
leading edge of the workpiece.
7) Slowly move the switch handle toward the
fence, completing the cut.
†…@
stop spinning before allowing the cutting head
„‡
xx…
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
10. Cutting bowed material
A bowed workpiece must be positioned against
the fence and secured with a clamping devise
before cutting as shown.
Warning: Do not position workpiece
incorrectly or try to cut the workpiece
„‡
x…
This will cause the blade to bind and could
$
11. Satellite workpiece support
Incorporated into the LH side of the machine
base is a removable satellite stand. Use this
stand to help support long pieces of material.
To remove the satellite stand, press the release
button on the top, and slide the stand from the
machine base. Position where convenient to
#
To replace, simply slide the satellite stand back
into the machine base until the release button
„‡
xV…
Fig 34
Fig 35
12. Adjustable stop plate
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
A stop plate designed for use during repetitive
!
on the RH side of the machine base. The stop
plate can be deployed in two positions, inboard
and outboard.
The inboard position enables repetitive cuts of
shorter lengths by positioning the stop plate
close to the blade. The outboard position is
used for the repetitive cutting of longer lengths
!
from the blade.
To deploy the stop:
1) Slide the release lock forwards.
2) Pull the stop(1) from its stored position
upwards and to the left. The stop will deploy.
3) Slide the release lock (2) backwards to lock
the stop into position.
4) To stow away, reverse the above steps. (See
xQ…
To deploy the stop outboard:
1) Slide the sprung-loaded lock (2) forwards.
2) Whilst holding the release lock, pull the stop (1)
from its stored position upwards and to the right.
The stop will deploy to the outboard position.
3) Slide the release lock (2) backwards to lock
the stop position.
4) To stow away, reverse the above steps. (See
x‰…
1
2
Fig 36
1
2
Fig 37
2
1
/x†
3
Adjusting the stop plate
Deploy the stop plate as outlined above.
1) Push the release button (1) on the front of the
machine base below the stop plate.
…‡
!
„…
base, and release the button (1) when at the
!
!
$
$
#„x… clockwise or
#
!
„‡
x†…
13. Extension Arm
With the stop plate in its stored position the
!
#
„‡
x†…
14. Cutting base moulding
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Base mouldings and many other mouldings can
be cut on a compound mitre saw. The setup of
the saw depends on moulding characteristics
and applications, as shown. Perform practice
"
P…\#
against fence and table. Use hold-down or
G-clamps, whenever possible, and place tape
on the area being clamped to avoid marks.
2) Reduce splintering by taping the cut area prior
to making cut. Mark cut line directly on the tape.
3) Splintering typically happens due to wrong
blade application and thinness of the material.
Note: Always perform a dry run cut so you can
determine if the operation being attempted is
possible before power is applied to the saw.
15. Cutting crown moulding
Your compound mitre saw is suited for the
#
properly, crown moulding must be compound
!
*
the ceiling and wall are at angles that, when
added together, equal exactly 90°. „‡
x€”[…
Most crown moulding has a top rear angle (the
*
…V‚
„
*
…x†‚
F
e
n
c
e
Mitre saw table
Mitre at 45o
[o
/x€
F
e
n
c
e
Mitre saw table
/[
F
e
n
c
e
In order to accurately cut crown moulding for a 90°
inside or outside corner, lay the moulding with its
#
*
When setting the bevel and mitre angles for
compound mitres, remember that the settings
are interdependent – changing one changes the
„‡
P”…
Mitre saw table
Fig 41
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
%HYHO0LWUH6HWWLQJV
Settings for standard crown moulding lying
*
Inside Corner
OL
IL
OR
IR
Outside Corner
Compound Cut Crown Mouldings
Fig 42
Note: The chart below references a
compound cut for crown moulding ONLY
WHEN THE ANGLE BETWEEN THE WALLS
EQUALS 90o.
KEY
BEVEL
SETTING
MITRE
SETTING
TYPE OF CUT
Inside Corner-Left side
IL
xx€[
31.6[Right
1)Position top of moulding against fence
2)Mitre table set at Right 31.6[
x…ƒ
Inside Corner-Right side
IR
xx€[
31.6[Left
1)Position bottom of moulding against
fence.
2)Mitre table set LEFT 31.6[
Outside Corner-Left side
OL
xx€
[
[
31.6 Left
1)Position bottom of moulding against
fence.
2)Mitre table set at Left 31.6[
x…@—|
Outside Corner-Right side
OR
xx€[
31.6[ Right
1)Position top of moulding against fence.
2)Mitre table set at RIGHT 31.6 [
x…@—|
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
MAINTENANCE
1
2
Fig 43
Danger:$
lubricants on the blade while it
is spinning.
Warning:
!
reaction, never use petrol, naphtha,
volatile solvents to clean the mitre saw.
Warning: For your safety, this saw
is double-insulated. To avoid
#
$
@
!
to avoid electrical shock.
Replacing carbon brushes
Replace both carbon brushes when either has
less than 6 mm length of carbon remaining,
or if the spring or wire is damaged or burned.
the saw. Then remove the black plastic cap
(1) on the side of the motor (2). Remove the
cap cautiously, because it is spring loaded.
Then pull out the brush and replace. Replace
for the other side. To reassemble reverse the
procedure. The ears on the metal end of the
assembly go in the same hole the carbon part
„‡
x…
Note:
make sure the brushes go back in the way
they came out. This will avoid serviceable
brushes undergoing a second ‘bedding
in’ process that could reduce motor
performance and increases wear.
Lower blade guard
Do not use the saw without the lower blade
guard. The lower blade guard is attached to the
saw for your protection. Should the lower guard
become damaged, do not use the saw until the
damaged guard has been replaced. Develop a
regular check to make sure the lower guard is
working properly. Clean the lower guard of any
dust or buildup with a damp cloth.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Warning: Do not use solvents on the
guard. They could make the plastic
“cloudy” and brittle.
Warning: When cleaning the lower
guard, unplug the saw from the power
!
Sawdust
Periodically, sawdust will accumulate under the work
movement of the worktable when setting up a mitre
/
Warning: If blowing sawdust, wear
proper eye protection to keep debris
from blowing into eyes.
Lubrication
All the motor bearings in this tool are lubricated
for the life of the unit under normal operating
conditions; therefore, no further bearing
ƒ
"&"\
&
"Œ
oil (sewing machine oil ) on metal-to-metal or
%%
\
!
—"„
actuates the lower guard movement) may be oiled
at the rear pivot, greased at ball bearing contact,
and oiled where the guard arm actuates the
acetyl roller of the lower guard, if the down chop
motion is hard.
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
!&
#
Local Authority or retailer for recycling advice.
PLUG REPLACEMENT
The fuse in the main plug of your power tool should
always be replaced with one of identical rating.
Check the voltage given on your power tool
matches the supply voltage.
follows the instruction below.
IMPORTANT
The wire in the mains lead are coloured in
"
Blue ---Neutral
Brown ---Live
The wire that is coloured blue must be connected to
the terminal that is marked with the letter N. The wire
that is coloured brown must be connected to the
terminal that is marked with the letter L. A 13AMP
(BS1363 or BS1363/A) plug must be used and a
Px\}
BLUE
N (NEUTRAL)
5 AMP
13
AMP
FUSE
BROWN
L (LIVE)
OUTER
SLEEVE
CABLE GRIP
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Declaration of Conformity
We, Importer
Erbauer (UK) Ltd.
^\†@
'
"
Complies with the essential health and safety
"
(& – EMC Directive
(& – Low Voltage Directive
(& – Machinery Directive
[[G€VGŠ&– Restrictions of the Use of Certain Hazardous
‡
[[G€QGŠ&and[[xGP[†GŠ&0
Š
Š
Š
„0ŠŠŠ…
‡
"
EN55014-1:2006
EN55014-2/A2:2008
EN61000-3-2:2006
EN61000-3-11:2000
EN61029-1:2009
EN61029-2-9:2002
EN60825-1:2007
Authorised Signatory
'
"VG[QG[P[
‡
"
]
"}
|
Erbauer (UK) Ltd
Quality Manager
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
ERBAUER 254MM (10”) SINGLE BEVEL SLIDING MITRE SAW
Download PDF