Viking | E-1600-20A-EWP | Specifications | Viking E-1600-20A-EWP Specifications

Viking E-1600-20A-EWP Specifications
TECHNICAL
Practice
Practice
TELECOM SOLUTIONS
FOR THE
BLK-3-EWP
Line Status Strobe
Light Kit with EWP
2 1 S T C E N T U RY
April 17, 2009
Provide Strobe Light Indication
of Line Status
Ideal for Use with Two-Button Emergency Phones!
The BLK-3-EWP provides high visibility indication of analog line status
through a high powered one million candle power strobe light.
The BLK-3-EWP is the ideal solution for the hearing impaired and can be
used equally well in loud warehouses or factories, where ringing phones
can not be heard. Alternatively, the BLK-3-EWP can be used to add emergency notification to pre-existing emergency phones by turning on the
strobe light when the emergency phone is in use.
The included LDB-3 control module has a disable input which is ideal for
two-button emergency phones, such as Viking’s E-1600-20A, allowing
“Info” button calls to be placed without activating the relay (turning on the
emergency strobe light, camera, etc.) Three DIP switches are provided for turning ring detection on or
off, off-hook/loop detection on or off and for selecting a ring cadence mode which allows the relay to follow ringing or to remain activated during the off time of standard ring cadence.
The control module can be installed on any standard telephone line or analog PABX/KSU station. The
1 million candle power strobe can be interfaced to flash on ringing, off-hook or a combination of ringing
and off-hook (line in-use). The LDB-3 ring/loop detect control module is also available separately.
The kit includes: (1) LDB-3 control module, (1) blue strobe light, (1) 12V DC power adapter, (13) gelfilled butt connectors and (1) single gang weatherproof mounting box with gaskets and hardware.
Features
• LDB-3 control module with Enhanced Weather
Protection (EWP) included
• Durable polycarbonate lens
• Long life 1 million candle power blue strobe light
• Flush mount or surface mount with weatherproof
single gang box (included)
• 3/4” knockouts for connecting conduit, etc.
• Strobe and control module may be installed separately
• Can be configured to signal: ringing, off-hook, or a
combination of both ringing and off-hook (line in-use)
• One set of (NO) normally open and (NC) normally
closed relay contacts provided
• Selectable ring cadence mode (strobe light will remain
flashing between rings)
• Switched 12V DC output (follows relay activation for
powering strobe lights, cameras, etc.)
• On/off switches for ring detection and off-hook/loop
detection
• Disable input, ideal for use with two-button emergency
phones (E-1600-20A), will not activate strobe light on
“Info” calls
Applications
• Ringing Phone or TTY indication for the hearing
impaired
• Ringing phone indication in loud warehouses and
factories
• Emergency illumination for emergency phones in
elevators, campuses, hallways, parking ramps, etc.
• Alarm indication for security systems or alarm panels
with phone dialers
Specifications
Power: 120V AC to 12V DC adapter provided
Strobe Dimensions: 111mm diameter x 69mm (4.38" x 2.75")
Control Module Dimensions: 74mm x 53mm x 25mm (2.9" x
2.1" x 1.0”)
Shipping Weight: 1.5 kg (3.3 lbs)
Operating Temperature: -26° to 54°C (-15° to 130° F)
Relay Contact Rating: .5A @ 125V AC/1A @ 30V DC
Minimum Loop Current: 15 mA
Minimum Ring Voltage: 25V RMS
Strobe Output: 1 million candle power @ 1 second flash rate
Ringer Equivalence: 0.5 A REN
Disable/Info Switch Input: 50mA/80mW maximum
Mounting: Fasten to wall, post, etc. with complete surface
mounting hardware included
Connections: Color coded wires with gel-filled butt connectors
Wa r r a n t y
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT
Our Technical Support Department is available for assistance weekdays between 8 a.m. and 5 p.m. central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. The customer MUST have a complete description of the problem, with all
pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched
between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect
shipments cannot be accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a P.O. Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting, a Return Authorization (R.A.) number will be issued.
This number is valid for fourteen (14) calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the product over the counter at no charge. The
distributor will then return the product to Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed the steps listed in 1, 2 and 3, be aware that you will have to pay a
restocking charge.
WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking
Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.
Vikings sole responsibility shall be to repair or replace (at Viking's option) the material within the terms stated above. VIKING SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND
INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESSED OR IMPLIED, OR FOR ANY
OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED BEYOND THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
Installation
0.6
LDB-3 Control Module
2.75
Red
Switched 12VDC Output
(Strobe Light Power)
11
Black
10
9
10
11
8
7
6
5
3
5
3
2
ON
S1
R
2
6
1
2
4
3
120V AC
* Gel-Filled Butt
Connectors (included)
Note: Polarity Sensitive!
12V DC
adapter
(included)
(+) Black
(-) Black with
White stripe
!
(-) Black with
White stripe
1.50
4.60
Relay Contacts
Common
Yellow
4.0
4.4
Normally Open
2.50
Blue
Disable/Info Switch Input
Blue
Gray
To Terminal Device/Phone
Brown
2
Green w/ Yellow Stripe
1
Red w/ Yellow Stripe
* Note: The gelfilled (water tight)
butt connectors are
designed for insulation displacement.
Do not strip wires
prior to terminating.
(+) Red with
Black stripe
1.05
Normally Closed
Purple
1
Z2
R
5
CR
2
4
Z3
R4
R7
R9
R8
8
9
7
Orange
Side View of the
Strobe Light (included)
To C.O. Line or Analog
PABX/KSU Station
Preparing the Power Supply
Step 1.
2.84
2.0
Back view of weatherproof
single gang box (included)
Step 2.
Step 3.
Connect power supply
wires to LDB-3 module
power supply wires
Step 1. Cut off the barrel connector.
Step 2. Seperate wires
Step 3. Connect 12V adapter wires to power
supply wires on LDB-3 Control Module
using supplied Butt Connectors and
then plug in power supply
(+) Black
(-) Black with
White Stripe
IMPORTANT: Do NOT plug in the
adapter until after Step 3 is completed.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone
line. It is recommended that a surge protector be installed to protect against such surges.
A. Installing the Strobe Light Using the Included Weatherproof Box
Nipple 1/2" x close
(2) 10-32 x 3/8" self
tapping screws
(2) 6-32 x 3/4" screws
* Gel-Filled Butt
Connectors (included)
Red
5
Red
(2) Knockout
Plugs
6
* Note: The gel-filled (water tight) butt connectors are designed for insulation displacement. Do not strip wires prior to terminating.
Black
R
5
CR
2
R
2
1
2
Z2
4
Z3
R4
R7
R9
R8
3
Black
LDB-3
Control Module
7/8" Nylon
spacer
Blue Strobe
Light
Foam
Gasket
Strobe
Mounting Ring
1/2" Close Nipple
Faceplate
Foam
Gasket
Weatherproof
Box
C. Rear Mounting Without Weatherproof Box
B. Front Mounting Without Weatherproof Box
The BLK-3-EWP Strobe Light Kit may be mounted without using the included weatherproof box. To mount the
strobe light from the front, use the diagram below.
Strobe Light
(included)
To mount the strobe light from the rear, use the
diagram below.
Strobe Light
(included)
Wall, post, etc.
2.75”
(2) #10-32 x 5/8
Phillips Head Self
Tapping Screws
(included)
To LDB-3
Control
Black Module
(included)
Red
To LDB-3 Red
Control
Module Black
(included)
(2) #8-32 x 2 1/2 Phillips
Head Self Tapping Screws (included)
Programming
A. DIP Switches
11
Sw 1
Sw 3
Description
ON
OFF
Ring Detection Only (see section B).
OFF
ON
Off-Hook/Loop Current Detection Only (see section B).
ON
ON
Ring and Off-Hook/Loop Current Detection (see section B).
9
8
7
OFF
Ring Cadence Mode OFF - relay is activated only during ringing.
5
3
Ring Cadence Mode ON - relay remains activated in between rings.
2
ON
ON
Ring Cadence Mode (see section C)
6
ON
S1
1
2
3
1
Sw 2
10
4
3
2
1
B. Configuring for Ring and/or Loop/Off-Hook Indication
(-) Black with
White stripe
* Gel-Filled Butt
Connectors
(included)
Red with
Yellow stripe
11
9
10
8
7
6
5
4
3
2
1
Incoming
Analog
Phone Line
Rear View of the
Strobe Light (included)
(+) Red with
Black stripe
3
(-) Black with
White stripe
2
(+) Black
ON
12V DC
Adapter
Included
LDB-3 Control Module
(included)
S1
120V AC
* Note: The gel-filled (water tight) butt connectors
are designed for insulation displacement. Do not
strip wires prior to terminating.
1
Note: The phone and
incoming line connections are NOT polarity
sensitive.
* Gel-Filled Butt
Connectors (included)
Note: Polarity Sensitive!
Red (+)
Red (+)
Green with
Yellow stripe
Phone or
Terminal Device
(not included)
Black (-)
Brown
Blue
Gray
1. Ring Indication Only
Black (-)
Orange
Blue
Disable Feature (see
Programming section F)
Purple
Yellow
N.C.
Auxiliary
COM.
Contact Output
N.O.
Connect the incoming line to the red and green wires with the yellow stripe as shown in the diagram. No phone/terminal device
is required. The LDB-3 control module can monitor for ringing any place along the ringing line.
2. Loop/Off-hook Indication Only
The LDB-3 control module must be placed between the phone line and the phone/terminal device to be monitored. Connect the
incoming line to the red and green wires with the yellow stripe and connect the phone/terminal device to the brown and gray
wires as shown.
3. Both Ring and Loop/Off-hook Indication
If the application requires ring and loop/off-hook indication, the LDB-3 control module must be placed between the phone line
and the phone/terminal device to be monitored. Connect the incoming line to the red and green wires with the yellow stripe, connect the phone/terminal device to the brown and gray wires.
C. Ring Cadence Mode
DIP switch 2 is used for switching between different ring detection modes. In the OFF position, the relay and switched 12VDC output will activate only while ring voltage is present and will turn off between rings. In the ON position, the relay and switched 12VDC
output will remain on for up to 5.75 seconds after the ringing has stopped. This allows the relay and 12VDC (flashing strobe light)
to remain on between rings of a standard ring cadence. Note: To use the Ring Cadence Mode, ring detection MUST be enabled
(DIP switch 1 - ON).
D. Relay Contacts
Normally open and normally closed relay contacts are available on the orange, purple and yellow wires. The contacts are rated at .5A @
125VAC/1A @ 30VDC. If contacts are driving an inductive load, place a suppression device at the load to snub high voltage spikes.
E. Switched 12V DC Output
The switched 12V DC output is a low current, 12-15VDC output that is turned on only while the ring/loop detect relay is activated.
This switched power output is ideal for lighting the included strobe light or providing 12-15V DC power to any device that draws less
than 350mAmps. The positive side is available on the red wire, and the negative side is on the black wire. Once all the line and
load connections have been made, plug in the 115 V AC wall adapter, and replace the cover.
F. Disable Feature
Model: xxxxxxx
P/N: xxxxxxx
S/N: XXXXXX
LDB-3
Control Module
Viking Electronics, Inc. (715)386-8861
1531 Industrial St., Hudson, WI 54016
1
2
3
Blue
2
5
ON
3
4
1
VIKING
Rear View of E-1600-20A
By connecting the Disable/Info Switch input of the LDB-3 control module to
the “Info” switch of Viking’s E-1600-20A, E-1600-20A-EWP, E-1600-52A or
E-1600-52A-EWP Emergency Phone, any outbound call initiated from the
“Info” button will not activate the strobe light. This way, only the
“Help/Emergency” outbound calls will activate the relay. Cut one of the “Info”
switch wires in half and connect each end to the blue wires on the LDB-3 control module as shown in the diagram at the right. Note: This Disable input is
NOT polarity sensitive. The “Disable” input can be connected to a switch for
remotely disabling/turning off the device (strobe light, camera, etc.) controlled
by the LDB-3. For more information, see DOD# 866.
Blue
6
7
8
9
10
11
Gel-Filled Butt
Connectors (included)
Operation
A. Ring Indication (DIP Switch 1 ON)
When the LDB-3 control module detects an incoming ring signal, it activates a set of normally open or normally closed contacts and
turns on the 12VDC output for activating the provided strobe light. With the Ring Cadence mode off (DIP switch 2 OFF), the relay
will activate and the strobe light will flash only during ringing. With the Ring Cadence mode ON (DIP switch 2 ON), the relay will
remain activated and the strobe light will remain flashing between rings.
B. Off-Hook Indication (DIP Switch 3 ON)
When the LDB-3 control module detects an off-hook condition (loop current) on the brown and gray wires, it activates a set of normally open or normally closed contacts and turns on the 12VDC output for activating the provided strobe light. The relay contacts
will remain activated and the blue strobe light will flash during the off-hook condition and will stop flashing approximately 3 seconds
after the phone/terminal device on the brown and gray wires is back on-hook.
Other Applications
A. Mounting the BLK-3-EWP with the E-1600-20A
The BLK-3-EWP can be used in conjunction with the E-1600-20A Two-Button Emergency Phone as
shown to the far right, however, special installation and mounting is required. Please follow the steps
below when using the BLK-3-EWP in conjunction with a surface-mounted E-1600-20A. A VE-5x5 surface-mount box is required, see DOD# 424.
Step 1. Drill or use a knockout punch to provide a .875” diameter hole in the top of the VE-5x5.
1/2" Liquid Tight
Conduit Connector
1/2" PVC Conduit
Straps
Step 2. Make all conduit connections.
Step 3. Make all wire connections to the LDB-3 control module.
1/2" Liquid Tight
Conduit
Step 4. Install the E-1600-20A as explained in its Technical Practice, DOD# 215.
11
B. Operating a BLK-3-EWP with a Contact Closure
10
E-1600-20A
and VE-5x5
(not included)
7
8
9
Z2
6
Wire Nuts
(not included)
R
2
Gray
4
390 Ohm - 750 Ohm, 1/2 Watt Resistor
(Radio Shack part # 271-1114, 271-1115,
271-1116, 271-1117 or equivalent)
3
120V AC
R
5
CR
2
5
Z3
R4
R7
R9
R8
1
2
Brown
Black with
White stripe
1/2" Liquid Tight
Conduit Connector
Black
Black with
White stripe
Red with
Black stripe
Red with
Yellow stripe
Green with
Yellow stripe
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 653
Printed in the U.S.A.
ZF301700 Rev C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising