Emerson CF776SW00 Owner's manual

Emerson CF776SW00 Owner's manual
READ AND SAVE THESE INSTRUCTIONS
MONTEREY LUMINA™
52” Ceiling Fan Owner's Manual
Model Numbers
CF776BS00 - Brushed Steel
CF776ORB00 - Oil Rubbed Bronze
CF776SW00 - Satin White
Net Weight:
28.9
Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
Part No. F40BP74680000
11/12
1-800-654-3545
www.emersonfans.com
Form No. BP7468
U.L. Model No.: CF776
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
!
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 15.9kg. (35 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan proves the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7
feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Before servicing or cleaning unit, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a warning device,
such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are
turning.
5. Do not operate reversing switch until fan blades have
come to a complete stop.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
Additional Safety Instructions for Installation
WARNING: To reduce the risk of electrical shock, this
fan must be installed with a general use, isolating
control/switch.
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2011” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
2
U.L. Model No.: CF776
Unpacking Instructions
!
PACKAGE CONTENTS
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
Part
A
1-800-654-3545
B
C
Ceiling Canopy
Coupler Cover
1
1
D
E
F
G
Blade Flanges
Fan Blades
Hanger Bracket
Hanger Ball/Downrod Assembly
5
5
1
1
H
I
J
K
Switch Housing Assembly
Switch Housing Cover Plate
Light Fitter Assembly
Glass Bowl
1
1
1
1
L
60-Watt (max.) Candelabra Bulbs
3
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
8
9
10
11
Quantity
1
G
HARDWARE CONTENTS
Part
1
2
3
4
5
6
7
Description
Fan Motor Assembly
A
Description
Threaded Studs, #8-32 x 1-1/4”
Knurled Knobs, #8-32
Lockwashers, #8
Wire Connectors, E3
Clevis Pin
Hairpin Clip
#10-32 x .25” Slotted Phillips
Washer Head Blade Screws
1/4-20 x .5” Round Head
Flange Screw (Spare)
12” Pull Chain w/ Large Wood Ball
12” Pull Chain w/Small Wood Ball
Blade Balance Kit
H
Quantity
2
2
2
3
1
1
I
B
J
C
16
K
1
1
1
1
D
E
L
F
2
1
4
8
5
9
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost. If
any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
3
6
10
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the top of the motor facing up.
The upper foam pad serves as a holder for the fan
during the first stages of assembly.
7
11
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length
Up to 50 ft.
50-100 ft.
Tools Needed for Assembly
One Phillips head screwdriver
One stepladder
One 1/4” blade screwdriver
One wire stripper
One 5/16” open end wrench, or pliers
Three wire connectors (supplied).
Wire Size A.W.G.
14
12
WARNING
!
Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 10). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Ceiling Fan Assembly
1. Remove the hanger ball by loosening the setscrew in
the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the pin
and hanger ball for reinstallation in step 4.
PIN
HANGER BALL
2. Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod
with the holes in the motor coupler. Install the clevis
pin and secure with the hairpin clip (Figure 2). The
clevis pin must go through the holes in the motor
coupler and the holes in the downrod. Be sure to
push the straight leg of the hairpin clip through the
hole near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis pin.
The hairpin clip must be properly installed to prevent
the clevis pin from working loose. Pull on the
downrod to make sure the clevis pin is properly
installed.
SETSCREW
DOWNROD
Figure 1
MOTOR
COUPLING
SETSCREW
CLEVIS PIN
HAIRPIN
CLIP
DOWNROD
JAM NUT
HAIRPIN CLIP
!
MOTOR
COUPLING
WARNING
SETSCREW
It is critical that the clevis pin in the motor coupler is
properly installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are properly
installed (as shown in Figure 2) could result in the fan
falling.
CLEVIS PIN
3. While pulling up on the downrod, securely tighten the
two setscrews in the motor coupler.
Figure 2
4
U.L. Model No.: CF776
4. Make sure the grommet is properly installed in the
coupler cover, then slide the coupler cover on the
downrod until it rests on the motor housing. Place
the ceiling cover over the downrod. Be sure that the
ceiling cover and the coupler cover are both oriented
correctly (Figure 3).
CEILING
COVER
5. Reinstall the hanger ball (Figure 4) on the downrod
as follows. Route the three 80” motor leads through
the hanger ball. Position the pin through the two
holes in the downrod and align the hanger ball so the
pin is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball. A
loose setscrew could create fan wobble.
DOWNROD
GROMMET
COUPLING
COVER
Figure 3
!
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened. Failure
to verify that the pin and setscrew are properly
installed could result in the fan falling.
DOWNROD
PIN
HANGER
BALL
6. The fan comes with blue, black and white leads that
are 80-inches long. Before installing the fan,
measure up approximately 6 to 9-inches above top
of hanger ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end of
leads.
CEILING
COVER
7. Mount blade flange to fan blade using three
#10-32 x .25” slotted Phillips washers head screws
(Figure 5).
Figure 4
8. Repeat this procedure for the remaining four blades
and flanges.
!
#10-32 x .25" SLOTTED
PHILLIPS WASHER HEAD
BLADE SCREW (3)
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
BLADE FLANGE
FAN BLADE
Figure 5
9. Turn the fan assembly upside down in preparation
for mounting the fan blade assemblies.
REMOVE SHIPPING
RETAINER AND
SCREW (5)
NOTE: Take care not to scratch fan housing when
installing blades.
10. Carefully unscrew each shipping retainers from the
motor housing. Discard the five screws and
shipping retainers (Figure 6).
11. Attach the blade assembly to the motor hub using
the two 1/4-20 x .5” round head flange screws
preassembled in flange. Make sure the screws are
tightened securely (Figure 6).
12. Repeat this procedure for the other four blade
assemblies.
SWITCH HOUSING
PLATE
BLADE
FLANGE
PREASSEMBLED 1/4-20 x .5"
ROUND HEAD FLANGE
SCREWS (2)
Figure 6
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
13. Remove one of the screws from the switch adapter.
Retain for future installation. Loosen the two
remaining screws in the switch adapter for
installation of the switch housing cover plate
(Figure 7).
REMOVE MOTOR
HOUSING SCREW
14. Place the switch housing cover plate onto the
switch adapter. Engage the keyholes of the switch
housing cover plate by rotating the switch housing
cover plate clockwise on the switch adapter.
Retighten the two screws and reinstall the screw
previously removed. Tighten all three screws
securely (Figure 7).
SWITCH HOUSING
COVER PLATE
LOOSEN MOTOR
HOUSING
SCREWS (2)
MOTOR
HOUSING
15. Remove the center plug screw from the switch
housing assembly (Figure 8).
16. Remove and retain the lockwasher and nut from
the light fitter. Insert the black and white wires from
the light fitter through the center hole in the switch
housing assembly. Thread the switch housing
assembly onto the light fitter. Reinstall the
lockwasher and nut and tighten securely (Figure 9).
Figure 7
17. Connect the white wire connector from the switch
housing assembly to the white wire connector of
the light fitter. Connect the blue wire connector from
the switch housing assembly to the black wire of
the light fitter (Figure 9).
CENTER PLUG SCREW
18. Engage the connector of the switch housing
assembly with the motor connector (Figure 10). The
two connectors are keyed and color-coded and
must be mated correctly (color-to-color) before they
can be engaged. Make sure the connector latch
closes properly.
SWITCH HOUSING
ASSEMBLY
19. Carefully tuck all wires and splices into the switch
housing.
SCREWS (3)
20. Remove the three switch housing screws from the
switch housing cover plate. Position the switch
housing assembly on the switch housing cover
plate and align the holes in the switch housing
assembly with the holes in the plate. Secure the
switch housing assembly by installing the three
screws (Figure 10).
SWITCH HOUSING ASSEMBLY
CONNECTOR
Figure 8
MOTOR
CONNECTOR
BLACK WIRE
NOTE: Do not pinch wires between the switch
housing assembly and the switch housing plate.
BLUE WIRE
HEX NUT
SCREWS
LOCKWASHER
SWITCH
HOUSING
ASSEMBLY
SWITCH HOUSING
PLATE
SWITCH
HOUSING
CONNECTOR
CONNECTORS
WHITE WIRES
FAN SWITCH
CHAIN
LIGHT FITTER
OUTER BOWL
CAP
FINIAL NUT
Figure 9
6
U.L. Model No.: CF776
20. Install three 60-watt (maximum) candelabra base
light bulbs (included) into the light fitter sockets
(Figure 11).
!
SWITCH HOUSING/
LIGHT KIT FITTER
ASSEMBLY
WARNING
SWITCH HOUSING
ASSEMBLY
CONNECTOR
Over lamping the fan will result in the light bulbs being
automatically shut off. Use only 60-watt maximum
candelabra light bulbs. Turn off the electricity before
replacing the light bulbs.
MOTOR HOUSING
CONNECTOR
21. Remove the finial nut and outer bowl cap from the
light fitter (Figure 12).
22. Pass the fan switch chain through the bushing in
the bowl cap (Figure 12).
!
WARNING
To avoid possible fire hazard, do not exceed wattage
indicated on the fitter.
Figure 10
23. Position the glass bowl over the threaded nipple.
Slide the outer bowl cap onto the threaded
nipple and gently tighten the finial nut to secure the
glass bowl. Pass the fan pull chain through the
bushing in the outer bowl cap and install the cap on
the threaded nipple. Install finial nut finger tight
(Figure 12).
FINIAL NUT
OUTER
BOWL CAP
60-WATT
CANDELABRA
BASE LIGHT
BULB (3)
CAUTION
Be sure that the fan switch chain does not make
contact with the light bulbs. If necessary
reposition the light fitter to avoid the fan switch
chain from touching the light bulbs.
SWITCH HOUSING/
LIGHT KIT FITTER
ASSEMBLY
24. Install pendants onto light fixture chain and fan
switch chain using couplers provided.
NOTE: It is advisable to periodically check the
tightness of the finial.
Figure 11
25. You have now completed the assembly of your new
ceiling fan. You can now proceed with hanging and
wiring your fan.
FAN SWITCH
CHAIN
LIGHT FITTER
THREADED NIPPLE
OUTER BOWL
CAP
60-WATT
CANDELABRA
BASE BULBS (3)
GLASS
BOWL
FINIAL NUT
LIGHT SWITCH
CHAIN
PENDANTS (2)
Figure 12
7
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 15.9kg. (35 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
Energy Efficient Use of Ceiling Fans
Using the Ceiling Fan Year Round. In the summer,
use the ceiling fan in the counter-clockwise direction.
The airflow produced by the ceiling fan creates a windchill effect, making you "feel" cooler. Select a fan speed
that provides a comfortable breeze, lower speeds
consume less energy. In the winter, reverse the motor
and operate the ceiling fan at low speed in the
clockwise direction. This produces a gentle updraft,
which forces warm air near the ceiling down into the
occupied space. Remember to adjust your thermostat
when using your ceiling fan - additional energy and
dollar savings could be realized with this simple step!
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure quality and
product performance.
Choosing the Appropriate Mounting Location.
Ceiling fans should be installed, or mounted, in the
middle of the room and at least 7 feet above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Emerson Retailer for optional
mounting accessories.
Turn Off When Not in the Room. Ceiling fans cool
people, not rooms. If the room is unoccupied, turn off
the ceiling fan to save energy.
8
U.L. Model No.: CF776
How to Hang Your Ceiling Fan
!
CEILING
WARNING
The fan must be hung with at least 7' of clearance from
floor to blades (Figure 13).
!
WARNING
AT LEAST
7'
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
15.9kg. (35 lbs.) or less”.
!
Figure 13
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 15.9kg. (35 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 14.)
!
FLOOR
TAB
HANGER
BRACKET
Figure 14
WARNING
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED
FOR CLARITY.
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
OUTLET
BOX
2. Carefully lift the fan and seat the hanger ball/
downrod assembly on the hanger bracket that was
just attached to the outlet box (Figure 15). Be sure
the groove in the ball is lined up with tab on the
hanger bracket (Figure 14).
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 15
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
!
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
9
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored
insulation). Securely connect wires with wire
connectors supplied. (Figure 16.)
!
GROUND
WIRE
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
!
BLACK AND BLUE
FAN WIRES
LISTED
WIRE
CONNECTOR (3)
WHITE SUPPLY
(NEUTRAL)
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
WHITE FAN
WIRE
BLACK SUPPLY
(HOT)
GREEN WIRE
(GROUND) FROM
HANGER BALL
NOTE: CEILING COVER
OMITTED FOR CLARITY.
Figure 16
WARNING
CEILING
COVER
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
LOCKWASHERS (2)
THREADED STUD (2)
2. Securely connect the fan motor white wire to the
supply white (neutral) wire using wire connector
supplied (Figure 16). Securely connect the fan motor
black wire and blue wire to the supply black (hot)
wire using wire connector supplied (Figure 16). After
connections have been made, turn leads upward
and carefully push leads into the outlet box, with the
white and green leads on one side of the outlet box
and the black and blue leads on the other side of the
outlet box.
!
KNURLED KNOB (2)
Figure 17
5. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and installing
the two knurled knobs (supplied). (Figure 17.)
Tighten the knurled knobs securely until the ceiling
cover fits snugly against the ceiling and the hole in
the ceiling cover is clear of the downrod. Your fan is
now wired to be turned on and off from the fan
switch.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
3. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
6. Connect the wood ball with chain to the 3-speed
switch pull chain. Connect the wood ball with chain
to the light fitter pull chain.
10
U.L. Model No.: CF776
Using Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. Check the operation of the fan by gently pulling on
the pull chain switch.
3. All fans are shipped from the factory with the
reversing switch positioned to the “left” circulate air
downward. If airflow is desired in opposite
direction, turn your fan OFF and wait for the blades
to stop turning, then slide the reversing switch to the
“right” position, and turn fan on again.
4. The fan blades will turn in the opposite direction and
reverse the airflow.
Your fan model is equipped with a 4-position,
3-speed pull chain switch. The operating sequence
is as follows:
Three-Speed
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
REVERSING
SWITCH
LIGHT PULL
CHAIN
SWITCH
Season
Summer
Winter
SPEED
CONTROL
PULL CHAIN
SWITCH
Reverse Switch Information
Rotation Direction
Switch Position
Counter-Clockwise
Left
Clockwise
Right
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan Light Kits (see store or catalog).
!
2. Ceiling Fan/Light Controls (see store or catalog).
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
3. Downrod Extension Kits (see store or catalog).
!
WARNING
WARNING
The use of any other control not specifically approved
for this fan could result in fire, shock and personal
injury.
11
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
Repair Parts
2
1
3
5
15
4
6
7
16
9
8
22
23
12
18
17
20
19
24
21
11
13
25
10
10
12
U.L. Model No.: CF776
Repair Parts Listing
Model Numbers
Key
No.
Description
CF776BS00
CF776ORB00
CF776SW00
760750-17
760750-32
760750-92
1
2
3
Hanger Ball Assembly,
Consisting of:
Hanger Bracket
Hanger Ball
Downrod, 4.5”
—
—
—
—
—
—
—
—
—
*
4
5
6
7
8
9
10
11
12
13
14
Parts Bag Containing:
Wire Connector (3)
Threaded Stud (2)
Lockwasher (2)
Knurled Knob (2)
Pin, Clevis
Clip, Hairpin
Wood Ball/Chain
Screw, 1/4-20 x .5” (1)
Screw, #10-32 x .25” (16)
Screw. Switch Cup (1)
Blade Balance Kit
764388-CHRM
—
—
—
—
—
—
—
—
—
—
—
764388-BLOX
—
—
—
—
—
—
—
—
—
—
—
764388-CHRM
—
—
—
—
—
—
—
—
—
—
—
15
16
17
18
19
20
21
22
23
24
25
Ceiling Canopy
Coupler Cover
Wiring Harness
Switch Housing Cover Plate
Switch Housing Assembly
Blade Flange (set of 5)
Fan Blade (set of 5)
Light Fitter
Glass Bowl
Outer Bowl Cap
Finial Nut
Owner's Manual
764389-BS
764390-BS
764391-BLK
764291-BS
764292-BS
764294-BS
764394-DC/DM
764396
764372-OM
764370-BS
764371-BS
BP7467
764389-ORB
764390-ORB
764391-BLK
764291-ORB
764292-ORB
764294-ORB
764394-DC/DM
764396
764372-AMM
764370-ORB
764371-ORB
BP7467
764389-SW
764390-SW
764391-WHT
764291-SW
764292-SW
764294-SW
764394-DC/DM
764396
764372-OM
764370-SW
764371-SW
BP7467
*
—
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
13
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
Trouble Shooting
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE
TROUBLE SHOOTING YOUR FAN.
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit breakers.
2. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
2. Check line wire connections to fan and switch wire
connections in the switch housing.wire connections in the
switch housing.
3. Reversing switch in neutral position.
3. Make sure reversing switch position is all the way to one side.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Screws securing fan blade flanges to motor
are loose.
2. Check to make sure the screws which attach the fan flanges to
the motor are tight.
3. Wire connectors inside switch housing rattling.
3. Check to make sure wire connectors in switch housing are not
rattling against each other or against the interior wall of the
switch housing.
4. Motor noise caused by solid-state variable
speed control.
4. Some fan motors are sensitive to signals from Solid-State
variable speed controls. If Solid-State Control is used and motor
noise results choose an alternative control method.
5. Screws holding blades to flanges are loose.
5. Tighten screws securely.
1. Setscrews in motor coupler are not
tightened securely.
1. Raise coupler cover and tighten setscrews securely.
2. Setscrew in the hangerball/downrod assembly is
loose.
2. Tighten the setscrew in the hangerball/downrod assembly.
3. Screws securing fan blade flanges to motor are .
loose
3. Check to be sure screws which attach the fan blade flanges to
the motor are tight.
4. Fan blade flanges not seated properly.
4. Check to be sure the fan blade flanges seat firmly and uniformly
to the surface of the motor. If flanges are seated incorrectly,
loosen the flange screws and retighten according to the
procedure in the section on "How to Put Your Ceiling
Fan Together".
5. Hanger bracket and/or ceiling outlet box is not
securely fastened
5. Tighten the hanger bracket screws to the outlet box, and/or
secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
!
2. Fan sounds noisy.
!
3. Fan wobbles
excessively.
14
WARNING: Make sure main power is turned off.
WARNING: Make sure main power is turned off.
U.L. Model No.: CF776
Emerson Air Comfort Ceiling Fan Limited Warranty
What The Limited Warranty Covers:
This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original
retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and
accessories of the Emerson Ceiling Fan against all defects in workmanship and materials.
What The Period Of Coverage Is:
This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's
Manual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered
by this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR
PROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO
COMPONENTS AND ACCESSORIES.
No Other Express or Implied Warranty Applies:
THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING
FAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE,
WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR
MANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE
ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME
OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM
STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
What We Will Do To Correct Problems:
If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during
the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or
workmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective
motor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no
replacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the
replacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.
How You Can Receive Warranty Service:
You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can
return your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and service
identification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that
information readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson
Customer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return
authorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at
the end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone.
What Is Not Covered:
This limited warranty does not extend to and expressly excludes:
• The glass globes and light bulbs of your Emerson Ceiling Fan,
• Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,
• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center,
use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse,
modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,
• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.
This limited warranty is deemed null and void upon the occurrence of either of the following events:
• You cease to own the Emerson Ceiling Fan product, or
• The Emerson Ceiling Fan is moved from its original point of installation.
This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent,
dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.
Limitation of Liability
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY
LAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING
FAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN
PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,
NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY
INDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential
damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or
equipment.
How State and Provincial Law Relates To The Warranty:
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
15
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF776
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-800-654-3545
www.emersonfans.com
Retain this manual for future use.
Part No. F40BP74680000
11/12
Form No. BP7468
U.L. Model No.: CF776
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement