Directed Electronics | Automate 210D | Installation guide | Directed Electronics Automate 210D Installation guide

210D
➤Owner’s/Installation
Guide
limited lifetime consumer warranty
For a period of one calendar year from the date of purchase of this auto-security device,
Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace
(with a comparable reconditioned model), free of cost, any electronic control module
which proves to be defective in workmanship or material under normal use, SO LONG
AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is necessary you must have
a clear copy of your sales receipt containing all of the information shown on the following page.
After the first calendar year, from the date of purchase of this auto-security device,
Directed Electronics, Inc., promises to the ORIGINAL PURCHASER to repair or replace
(with a comparable reconditioned model) any electronic control module which proves to
be defective in workmanship or material under normal use FOR A CHARGE OF $45.00,
SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A
PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH
THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is necessary you
must have a clear copy of your sales receipt containing all of the information shown on
the following page.
This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or understandings, whether written or oral.
IN ANY EVENT, DIRECTED ELECTRONICS, INC. IS NOT LIABLE FOR THE
THEFT OF THE VEHICLE AND/OR ITS CONTENTS.
This warranty is void if the product has been damaged by accident, unreasonable use,
neglect, improper service or other causes not arising out of defects in materials or construction. This warranty is nontransferable and does not apply to any unit that has been
modified or used in a manner contrary to its intended purpose and does not cover batteries. The unit in question must be returned to the manufacturer, postage prepaid. This
warranty does not cover labor costs for the removal, diagnosis, troubleshooting or reinstallation of the unit. For service on an out-of-warranty product a flat rate fee by model is
charged. Contact your authorized dealer to obtain the service charge for your unit.
These systems are a deterrent against possible theft. Directed Electronics, Inc. is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and/or its contents. Directed Electronics
does not authorize any person to create for it any other obligation or liability in connection with this security system.
© 2003 directed electronics, inc.
i
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY
PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS
EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY
AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL
WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED
STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER
OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR
LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOWING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
IMPORTANT NOTE:
This product warranty is automatically void if its date code or serial number is defaced,
missing, or altered. This warranty will not be valid unless you have completed the warranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the
address listed on the warranty registration card.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤
➤
➤
➤
➤
➤
➤
➤
➤
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2003 directed electronics, inc.
table of contents
limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
installation tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
primary harness (H/1), 12-pin connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
step 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
step 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
step 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
step 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
step 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
step 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
step 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
step 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
step 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
step 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
transmitter/receiver learn routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
operating settings learn routine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
to access another feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
to exit the learn routine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
features menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
feature descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
arming with transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
arming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
disarming with transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
manual valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
remote valet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
© 2003 directed electronics, inc.
1
diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
code hopping ™ re-synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
wiring quick reference diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2
© 2003 directed electronics, inc.
what is included
➤
On board Double Guard Shock Sensor
➤
Control Module
➤
Two 3-Button Transmitters
➤
12-Pin Main H/1 Harness
➤
Plug-in Status LED
➤
Plug-in Valet®/Program Button
➤
514 Revenger Siren
➤
Starter Kill Harness
installation tools
➤
Digital Multi-Meter
➤
Drill
➤
9
➤
Screwdrivers
/32 and 5/16 Drill Bits
(Phillips and Flathead)
➤
Wire Stripper
➤
Solder Iron
➤
Electrical Tape
➤
Pliers
➤
Crimping Tool
note: The installation tools required will vary depending
on your vehicle.
© 2003 directed electronics, inc.
3
important information
Congratulations on the purchase of your security entry system.
This system will allow convenient access to your vehicle with the
push of a button, as well as other optional features. Properly
installed, this system will provide years of trouble-free operation.
Please take the time to carefully read this Owner’s/Install Guide
in its entirety and watch the Rattler Do-It-Yourself Installation
Video prior to installing your system.
You can print additional or replacement copies of this manual by
accessing the Directed web site at www.diyrattler.com.
important! If you are not comfortable working with electronics or unfamiliar with the tools required, please contact your local dealer for advice or ask to have the remote
start professionally installed to avoid costly damages.
Failure to properly install the security system may result
in property damage, personal injury, or both.
➜ system maintenance
The system requires no specific maintenance. Your remote is
powered by a miniature 3-volt battery (type CR2032) that will
last approximately one year under normal use. When the battery
begins to weaken, operating range will be reduced and the LED
on the remote will dim.
4
© 2003 directed electronics, inc.
➜ your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Please note that it is necessary to keep your proof of purchase.
➜ fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
© 2003 directed electronics, inc.
5
primary harness (H/1),
12-pin connector
6
H1/1
ORANGE
(-) 500 mA Ground-When-Armed Output
H1/2
WHITE
H1/3
WHITE/BLUE
H1/4
BLACK/WHITE
H1/5
GREEN
H1/6
BLUE
H1/7
VIOLET
H1/8
BLACK
H1/9
YELLOW
(+) Ignition Input, Zone 5
H1/10
BROWN
(+) Siren Output
H1/11
RED
H1/12
RED/WHITE
(+) Light Flash Output
(-) 200 mA Channel 3 Validity Output
(-) 200 mA Dome light Supervision Output
(-) Door Trigger Input, Zone 3
(-) Instant Trigger, Zone 1
(+) Door Trigger Input, Zone 3
(-) Chassis Ground Input
(+) 12V Constant Power Input
(-) 200mA Channel 2 Validity Output
© 2003 directed electronics, inc.
installation
Be sure to read this section thoroughly and view the Rattler DoIt-Yourself Installation Video in its entirety before starting the
installation. Pay special attention to all warnings to prevent
personal injury or damage to your vehicle.
www.diyrattler.com) to get
Visit our 24-hour technical Web site (w
a vehicle-specific wiring guide prior to starting this installation. If
at any time during the installation you are unable to answer your
questions on the Web site, call 1-800-873-1314 for live technical
assistance.
warning! On vehicles with air bags or supplemental restraint systems (SRS) you may
notice a bright yellow tube with small wires
in it marked SRS underneath the steering
column near the key cylinder. DO NOT
tamper or unplug these for any reason to
prevent costly damages to your vehicle or
personal injury. Tampering may cause
unintended deployment of airbags.
warning! DO NOT use any testing tool
other than a digital multi-meter to prevent
costly damages to your vehicle. Use of a test
light may cause grounding of sensitive electrical components that can damage the onboard vehicle computer and processors
resulting in substantial cost for replacement.
warning! Verify that the vehicle is set to
park and that the parking brake is set
before beginning installation.
© 2003 directed electronics, inc.
7
➜ step 1
Plug-in LED and Valet®/Program switch
The LED and the Valet®/Program switch both plug into the
control module. The status LED plugs into the white two-pin
port, while the Valet®/Program switch should be plugged into the
blue two-pin port. The status LED and Valet®/Program switch
each fit into 9/32-inch holes.
Status LED
Valet®/Program Switch
DIA-41
When mounting the LED it will be necessary to locate an area on
the dash that is visible from all sides of the vehicle, and has at
least 1 inch of clearance behind the mounting area. It is recommended that a factory "pop-out" be used for the LED mounting,
using a 9/32 drill bit drill a hole in the location selected, feed the
LED through the hole, press the LED firmly until it snaps into
place. Run the wires to the selected control module mounting
location using caution to NOT run the wires near any moving
objects or excessive heat.
The Valet®/Program switch is usually mounted under the dash or
in the glove box, the same precautions used for the LED should
be followed. Once a location has been selected drill a 9/32 hole,
8
© 2003 directed electronics, inc.
feed the wires through the hole and press the switch firmly until
it snaps into place. Run the wires to the same location as the LED
using caution to NOT run the wires near any moving objects or
excessive heat.
➜ step 2
Ground Wire
The BLACK wire on the main 8-pin harness is ground. This wire
should be connected to a clean, paint-free area of metal in the
drivers kick panel area. First strip back a ¾-inch section of the
insulation off the BLACK wire and crimp a ring terminal (not
provided) to that wire. Locate a clean, paint-free metal surface in
the drivers kick panel. Using a self-tapping screw, drill the screw
with the ring terminal to the metal area. Once screwed down,
pull on the wire to ensure a good connection.
note: More problems are attributed to poor ground connections than any other cause. Take extra care to ensure
the ground is clean and secure.
© 2003 directed electronics, inc.
9
SELF-TAPPING
BOLT OR SCREW
GROUND
WIRE
DIA-591
NOTE: REMOVE ANY PAINT
BELOW RING CONNECTOR
RING
CONNECTOR
➜ step 3
Constant Power and Ignition wires
Almost all power and ignition wires can be found behind the key
cylinder under the lower drivers side dash panel. Using the
appropriate hand tools, remove the lower dash panel using care
not to break any parts. If the panel does not come off easily
check for any additional screws you may have missed.
Once the lower dash panel has been removed, locate the ignition
harness at the back of the key cylinder. This is usually a group of
10
© 2003 directed electronics, inc.
thicker wires. With the ignition harness exposed, use your digital
multi-meter to find your power and ignition wires.
Place the black lead of the meter to a clean metal surface in the
kick panel area and secure it. Put the meter in the DC voltage
position, then take the red lead of the meter and probe one of the
thicker gauge wires. The color and identity of your specific
vehicle wiring can be obtained at www.diyrattler.com. With the
key in the OFF position, test the suspect wire. The constant
power wire will read between 11.00 volts and 13.00 volts regardless if the key is on or off.
Once the constant power wire has been identified, solder the
RED wire from the 12-pin harness to it and cover the connection with electrical tape to ensure a safe connection.
With the meter black lead still in the kick panel, locate the ignition wire harness in the same location. It will test differently than
constant (+)12 volts. Locate the suspected wire using the
www.diyrattler.com Web site and place the red lead of the meter
on the suspected wire. With the key in the off position the meter
will read 0.00 volts. Turn the key to the on position and the meter
should read between 11.00 volts and 13.00 volts. Now watching
the meter, turn the key to the crank position and the voltage
should drop a small amount but not disappear. If the voltage
disappears this is not an ignition wire but an accessory wire. If the
wire meters correctly, solder the YELLOW wire from the 12-pin
harness to it and cover the connection with electrical tape.
© 2003 directed electronics, inc.
11
➜ step 4
Starter wire
The starter wire will be located in the same harness as the ignition
and constant power. Leaving the meter black lead connected to
the metal ground.
Find the wire suspected to be the starter wire according to the
web information on your vehicle. Place the red lead of your
meter on the wire. With the key in the off position the meter
should read 0.00 volts and will stay at 0.00 volts in all key positions except the crank position. In the crank position your meter
should read between 10.00 volts and 13.00 volts, and will drop
back to 0.00 volts when the starter disengages. Once you locate
the starter wire, cut the wire in half and try to start the vehicle.
(Always check the Web site information on your vehicle for
warnings regarding the starter wire and check engine lights.
Some vehicles will trip a check engine light if the starter wire is
cut.) If the vehicle does not start, the correct wire has been identified. Once correctly identified solder the separate ends that you
have cut to the heavy gauge black wires on the 2 pin harness and
cover the connections with black tape.
12
© 2003 directed electronics, inc.
Connect the BLACK starter kill wires as shown below. Use one of
these wires as the starter kill input and the other as a starter kill
output wire (these wires are interchangeable).
➜ step 5
Parking light flash
There are several different types of parking light circuits. The
following description is for a standard positive-triggered parking
light circuit, usually located at the light switch. If the web vehicle
information suggests a different type of parking light circuit,
please contact Rattler Technical Support.
Using the web information on the vehicle, locate the suspected
wire and place the BLACK lead of the meter to a ground and
secure it. Place the multi-meter in the DC position. Using the
RED lead of the meter, probe the wire. With the switch in the
off position the meter will read 0.00 volts. While watching the
meter, turn the switch to the parking light position. The meter
will read between 10.00 volts and 13.00 volts.
© 2003 directed electronics, inc.
13
important: While reading the meter turn (adjust) the
dash dimmer control switch. The voltage should not vary
on the meter. If the voltage does vary the incorrect suspected wire has been tested. Find the correct wire and
retest.
Once you have identified the correct wire, solder the WHITE
wire on the main connector to it and cover the connection with
electrical tape.
➜ step 6
Door triggers
The door trigger is the circuit in the vehicle that tells the dome
light to come on when the door is opened. This wire can be
either a positive 12 volt polarity or more commonly a negative
ground polarity, the door trigger wire is mandatory for all security systems and can usually be identified on
www.diyrattler.com. Using the information sheet for your
specific vehicle locate the suspect wire, if the door trigger listed
for your car is a negative type door trigger place the red lead of
your meter to a constant 12 volt source and secure it, take the
14
© 2003 directed electronics, inc.
black lead of the meter and probe the suspect wire with the door
open, you will see 11.00 to 13.00 volts appear on the meter,
secure the black meter lead to the suspect wire and close the door
with the display on the meter visible, if you have the right wire
the voltage will drop to 0.00 volts, open the passenger door to
verify that the wire sees both doors. Once confirmed solder the
GREEN (H1/5) wire on the 12 pin harness to it and cover the
connection with black tape.
Some vehicles (mainly FORD) have a positive 12volt door
trigger if this is the case in your vehicle place the Black lead of
your meter to chassis ground and secure it, place the Red lead
of your meter to the suspect wire with the door opened the
meter should read 12.00 to 13.00 volts secure the red lead and
close the door with the meter display visible, when the door is
closed the meter should read 0.00 volts, open the passenger side
door and the meter should read 12:00 to 13:00 volts. Once
confirmed solder the VIOLET (H1/7) wire to it and cover the
connection with electrical tape.
Some newer vehicles have multiple door triggers or a wire for
each door, if this is the case it may be necessary to diode isolate
the triggers so the security system can see all triggers without the
door triggers seeing each other. If your Vehicle has more than
one door trigger listed on the vehicle information sheet please
refer to the web site or call technical support.
© 2003 directed electronics, inc.
15
➜ step 7
Dome light supervision (optional)
The dome light wire is optional and not required for normal
operation, however if desired you can have the security system
turn on the dome light when the system is disarmed. If you
would like this feature please refer to the web site or call technical support.
➜ step 8
Siren connection
The siren should be located under the hood of the vehicle and
clear of any moving parts and anything that generates an
extreme amount of heat, find a location that will accommodate
these requirements and with a couple of self tapping screws
mount the siren facing downward. With the siren securely
mounted cover the first 12 inches of the siren wire with electrical
tape, Locate a rubber grommet that you can gain access to and
with a sharp object poke a hole through the grommet, using
electrical tape attach the end of the siren wire to the sharp object
and poke it back through the existing hole, from the inside of
the vehicle pull the remaining slack of the siren wire into the car
and remove the sharp object. Route the wire to the desired position making sure to keep it away from all moving parts. Now
solder the Red wire of the siren to the BROWN (H1/10) wire
on the 12 pin main harness, cover the connection with electrical
tape. Ground the Black siren wire to the same location as the
BLACK (H1/8) wire of the 12 pin main harness.
16
© 2003 directed electronics, inc.
➜ step 9
Optional connections (channel 2, 3)
When the system receives the code controlling channel 2, for
longer than 1.5 seconds, the RED/WHITE wire (H1/12channel 2) will supply an output as long as the transmission
continues. This is often used to operate a trunk/hatch release or
other relay-driven function.
When the system recieves the code controlling channel 3, the
output is instantaneous, and the WHITE/BLUE wire (H1/3channel 3) will supply an output as long as the transmission
continues. This is used to operate an accessory function.
important: Never use these wires to drive anything but a
relay or a low-current input! The transistorized output
can only supply 200 mA of current. Connecting directly
to a solenoid, motor, or other high-current device will
cause it to fail.
© 2003 directed electronics, inc.
17
➜ step 10
Hood/trunk pins
The BLUE (H1/6) wire will respond to a negative input with an
instant trigger. It is ideal for hood and trunk pins and will report
on Zone 1. It can also be used with Directed Electronics 506T
Glass Breakage Sensor, as well as other Directed Electronics
single stage sensors.
➜ step 11
Adjusting the shock sensor
note: The control module must be mounted in its permanent location before adjustments are made.
important: Ensure that the adjustment screw on the control module is accessible in the permanent location.
The double guard shock sensor is a two stage sensor; with both
warn away trigger and full trigger zones. Adjustment of the
sensor will affect both zones simultaneously. To adjust the sensor,
turn the adjustment screw on the side of the control module.
■ For a more sensitive setting turn the adjustment screw clockwise
in small increments, testing the sensitivity after each adjustment
until the desired setting is achieved.
■ For a less setting turn the adjustment screw counter clockwise in
small increments, testing the sensor after each adjustment until
the desired setting is achieved.
18
© 2003 directed electronics, inc.
➜ step 12
Testing the system
With all the previous steps completed, the operation of the
system can now be tested.
■ Close all the doors and press the
button on the transmitter,
the system should chirp one time.
■ At this point the system will go through diagnostics, a 15 second
process in which the security system will analyze the status of all
connected zones.
■ After 15 seconds open the driver side door, the alarm should
emit a series of chirps to indicate a security breach, after several
chirps the system will go into full trigger and the siren will
sound.
■ At any point during the chirps or full trigger press the
but-
ton again and the system should turn off.
■ Rearm the system and test the remainder of the doors.
■ After testing the doors sit in the vehicle and close the doors,
rearm the system and after 15 seconds turn the key on, the system will emit a series of chirps and then go into full trigger, at
this time attempt to start the vehicle it should NOT crank.
■ Press the
button on the transmitter to disarm the system
and cycle the ignition key off, on, off to reset the system.
■ Rearm the system, wait 15 seconds and lightly bump the tire
with your foot, the system should emit a series of chirps, kick the
tire a little harder and the system should go into full trigger.
■ Disarm the system.
This completes the testing, if all functions and zones do not
© 2003 directed electronics, inc.
19
work correctly check your wiring against the manual and verify
all connections. If you still are experiencing problems contact
Rattler technical support.
note: If the shock sensor does not operate as described,
see the Shock sensor adjustment section of this guide.
transmitter functions
The receiver uses a computer-based learn routine to learn the
transmitter buttons. This makes it possible to assign any specific
transmitter button, or combination of buttons, to any receiver
function. The transmitter initially comes programmed in the
Standard Configuration, but may also be customized. Unless
otherwise specified, the buttons used in all of the instructions in
this manual correspond to a Standard Configured transmitter.
20
© 2003 directed electronics, inc.
➜ standard configuration
Button
The arm/disarm function is controlled by pressing
.
Button
This channel 2 accessory
is used for trunk release.
Button
This channel 3 accessory
is an additional channel for optional
accessory functions such as remote start.
© 2003 directed electronics, inc.
21
transmitter/receiver
learn routine
The system comes with 2 transmitters that have been taught to
the receiver. The receiver can store up to 4 different transmitter
codes in memory. Use the following learn routine to add transmitters to the system or to change button assignments if desired.
The Valet®/Program switch, plugged into the blue port, is used for
programming. There is a basic sequence of steps to remember whenever programming this unit: Door, Key, Choose, Transmit and
Release.
1. Open a vehicle door. (The GREEN wire,
H1/5, or the VIOLET, H1/7 must be connected.)
2. Key. Turn the ignition to the ON position.
22
© 2003 directed electronics, inc.
3. Choose. Within 10 seconds, press and
release the Valet®/Program switch the number
of times for the desired function. Then press
the switch once more and hold it. The siren
will chirp and the LED will flash to confirm
the selected channel. Do not release the
Valet®/Program switch.
Channel number
Function
1
Auto Learn
2
Arm/Disarm
3
Channel 2 Output
4
Channel 3/Remote Start
5
Delete all Transmitters
4.
Transmit.
While
holding
the
Valet®/Program switch, press the desired
button to be programmed on the transmitter.
5. Release. Once the button is learned, the
siren will chirp, confirming transmitter
programming. The Valet®/Program switch can
now be released.
© 2003 directed electronics, inc.
23
Auto Learn function
This function provides a 1–step programming of the transmitter
to the following factory default settings:
➤
Button
—Lock/Unlock
➤
Button
—Channel 2 output
➤
Button
—Channel 3/Instant output
note: All programmable features will be reset to factory
default settings.
Delete all Transmitters
In case the transmitter(s) is lost or stolen, this function provides
removal of all transmitter(s) access from the system memory.
Learn Routine will be exited if:
➤
The doors are closed.
Ignition is turned off.
Valet®/Program switch is pressed too many times.
➤
More than 15 seconds elapses between programming steps.
➤
➤
24
© 2003 directed electronics, inc.
operating settings learn routine
Many of the operating settings of this unit are programmable.
They can be changed whenever necessary through the Operating
Settings Learn Routine™. The Valet®/Program push-button
switch, plugged into the blue port, is used together with a
programmed transmitter to change the settings.
To enter the System Features Learn Routine™:
1. Open a door. (The GREEN wire, H1/5, or
the VIOLET, H1/7 must be connected.)
2. Ignition. Turn the ignition on, then back off.
(The H1/9 YELLOW switched ignition input
must be connected.)
Choose. Within 10 seconds, press and
release the Valet®/Program switch the number
3.
of times for the desired function. Then press the
switch once more and hold it. The siren will
chirp and the LED will flash to confirm the selected channel. Do
not release the Valet®/Program switch.
© 2003 directed electronics, inc.
25
Transmit. While HOLDING the
4.
Valet /Program switch, you can select the
®
desired feature settings using the remote transmitter. Pressing Button
while HOLD -
ING down the Valet /Program switch will program the feature
®
to the LED ON settings. The siren will chirp once to indicate
the one-chirp setting has been selected. Pressing Button
while HOLDING down the Valet®/Program switch will change
the setting to the LED OFF setting. The siren will chirp twice
indicating that the LED OFF setting has been selected.
5. Release. Release the Valet®/Program switch.
➜ to access another feature
You can advance from feature to feature by pressing and
releasing the Valet®/Program switch the number of times necessary to get from the feature you just programmed to the feature
you wish to access. For example, if you just programmed Feature
1 and you want to program Feature 2:
1.
Release the Valet®/Program switch.
2.
Press and release the Valet®/Program switch ONCE to
advance from Feature 1 to Feature 2.
3.
26
Press the Valet®/Program switch once more and HOLD it.
© 2003 directed electronics, inc.
4.
The siren will chirp two times to confirm that you have
accessed Feature 2, Confirmation Chirps.
➜ to exit the learn routine
To exit the learn routine, do one of the following:
1.
Close the open doors.
2.
Turn the ignition on.
3.
No activity for longer than 15 seconds.
4.
Press the Valet®/Program switch at least 9 times.
© 2003 directed electronics, inc.
27
features menu
The factory defaults are indicated in bold text in the table below.
Feature
Number
Default LED
On Setting
(press transmitter
button 1)
LED Off Setting
(press transmitter
button 2)
1
Active Arming
Passive Arming
2
Confirmation
chirps ON
Confirmation
chirps OFF
3
No Feature
4
No Feature
5
No Feature
6
No Feature
7
Code Hopping ON
Code Hopping OFF
note: The number in parentheses indicate the number of
times the LED will flash. The Factory defaults are indicated in bold type.
28
© 2003 directed electronics, inc.
feature descriptions
1
ACTIVE/PASSIVE ARMING: When active arming is selected,
the system will only arm when the transmitter is used. When set
to passive, the system will arm automatically 30 seconds after the
last door is closed. Passive arming is indicated by the rapid flashing of the LED when the last protected entry point is closed.
2
CONFIRMATION CHIRPS ON/OFF: This feature controls
the chirps that confirm the arming and disarming of the system.
3
NO FEATURE
4
NO FEATURE
5
NO FEATURE
6
NO FEATURE
7
CODE HOPPING ™ ON/OFF: This system features Code
Hopping™ as an option. Code Hopping™ is a feature that uses a
mathematical formula to change the system’s code each time the
transmitter and receiver communicate. This makes the group of
bits or "word" from the transmitter very long. The longer the
word is, the easier it is to block its transmission to the unit.
Disabling the Code Hopping™ feature lets the receiver ignore the
Code Hopping™ part of the transmitted word. As a result, the
unit may have better range with Code Hopping™ off.
© 2003 directed electronics, inc.
29
using your system
➜ arming with transmitter
Pressing
for one second will arm the system. The parking
lights will flash once and the siren will chirp once to confirm
that the system is armed.
➜ arming without a transmitter
The security system also can be programmed to arm itself
without a transmitter (called passive arming). If the system is
programmed for passive arming, it will automatically arm 30
seconds after the ignition is turned off and the system sees you
leave the vehicle by opening and closing a door. After the last
protected entry is closed the LED rapidly flashes for 30-seconds
and the parking light flash and the siren chirps. The system
arms at 30 seconds, but the siren will not chirp.
note: If any protected entry point (a door or a switch-protected trunk or hood) is open, the system will not passively arm. Additionally, each time a protected entry is
triggered during the arming countdown, the 30-second
countdown starts over.
When armed, your vehicle is protected as follows:
➤
➤
30
The LED will flash as a visible theft deterrent.
Light impacts will trigger the Warning Zone signal. When
triggered, the siren will sound for a few seconds.
© 2003 directed electronics, inc.
➤
➤
Heavy impacts will trigger the system. The triggered
sequence is 30-seconds of constant siren sounding and
flashing parking lights.
If a protected entry (door, hood, or trunk) is opened, the
system will immediately trigger the siren and flash the
parking lights. The hood and trunk are instant alarm triggers. The door is a progressive trigger (a series of rapid chirps
for a few seconds before the alarm sounds). The progressive
trigger allows time for you to disarm of the system prior to
the alarm.
➜ disarming with transmitter
To disarm the system press
for one second. The parking
lights will flash twice and the siren will chirp twice to confirm
that the system is disarmed.
© 2003 directed electronics, inc.
31
➜ disarming without a transmitter
If your remote transmitter is lost or damaged, you can manually
disarm your vehicle security system. To disarm the system
without a transmitter, you must have the vehicle's ignition key
and know where the Valet®/Program switch is located. Be sure
to check with your installer at the time of installation for its location.
To disarm the security system:
1.Turn the ignition key on.
DRW-35
2.Press the Valet®/Program
switch within 15 seconds. The
system will now disarm.
note: If the system does not disarm, you may have
waited too long to press the Valet®/Program
switch; turn the ignition off and repeat the process.
➜ panic mode
If you are threatened in or near your vehicle, you can press
for 1.5 seconds to trigger Panic Mode on your security system
and attract attention. The siren will sound and the parking lights
32
© 2003 directed electronics, inc.
will flash for 30-seconds. To stop the Panic Mode at any time,
press
again.
➜ silent mode
Use the Silent Mode to temporarily turn off the arm or disarm
chirps by briefly pressing
before pressing the
when
arming or disarming. The confirmation chirp(s) will then be
eliminated for that one operation only. To permanently turn off
the arm and disarm chirps, see the programming section of this
guide.
note: The Warn Away Response to lighter impacts is
bypassed if the system is armed using the Silent Mode.
This ensures that the siren does not chirp in an environment where you do not want chirps to be emitted. The
system is still capable of being triggered by heavier
impacts; only the Warn Away Response generated by
light impacts is bypassed.
➜ valet mode
Valet Mode prevents your security system from passive arming.
All transmitter convenience functions (door locks, trunk release,
etc.) remain operational. This feature is useful when washing or
servicing your vehicle. You can access Valet Mode either manually or from the remote transmitter.
© 2003 directed electronics, inc.
33
➜ manual valet mode
To enter or exit Valet Mode with the Valet®/Program switch:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the
Valet®/Program
switch
DRW-35
within 10 seconds.
The status LED will light steady if you are entering Valet Mode
and will turn off if you are exiting Valet Mode.
➜ remote valet
You can also enter or exit Valet Mode by using the remote
transmitter:
1. Open any vehicle door.
2. Press
.
3. Press
.
4. Press
again.
The status LED will light steady if you have entered Valet Mode
and will turn off if you have exited Valet Mode.
note: In Valet Mode the LED will turn off if the ignition
is turned ON. The LED will turn back on if the ignition
is turned OFF. This notifies you that the system is still in
Valet Mode.
34
© 2003 directed electronics, inc.
diagnostics
The microprocessor at the heart of your system has the ability to
constantly monitor all of the switches and sensors connected to
it. It can detect any faulty switches or sensors and prevent them
from disabling the entire system. It can also record and report
any triggers that occur when you are away from your vehicle.
➜ arming diagnostics
If the system is armed at the same time that an input is active
(door opening, sensor triggering, etc.), you will hear one chirp
to indicate arming and a second chirp a few seconds later to
indicate Bypass Notification.
A Bypass Notification chirp means that the system ignores the
input that was active when the system was armed, until that
input ceases. Three seconds after that input ceases, the system
will resume normal monitoring.
For example, if your vehicle has an interior light exit delay and
you arm the system before the light turns off, you may hear a
Bypass Notification chirp. Three seconds after the light turns
off, however, normal monitoring resumes.
note: Bypass Notification does not occur when the system is in Silent Mode™ or if the chirps have been programmed not to sound.
© 2003 directed electronics, inc.
35
➜ disarming diagnostics
Your system has a Tamper Alert feature that notifies you of
system triggers that occur while you are away from your vehicle.
If you hear four chirps when you disarm, this indicates that the
system was triggered in your absence.
If you hear five chirps when you disarm, this indicates that a
specific zone was triggered so many times that the NPC™ has
bypassed that zone.
In both cases, the pattern of the flashing status LED indicates
which zone was triggered (see Table of Zones).
The LED does not, however, report when Warn Away Responses
have activated; it only reports Triggered Sequences. The system
retains this information in its memory and will continue to
chirp four or five times each time the system is disarmed, until
the next time the ignition is turned on.
36
© 2003 directed electronics, inc.
➜ system status chirps
ACTION
NUMBER OF CHIPS
Arm
1
Arm
1 (3-second delay), 1
DESCRIPTION
System armed
System armed with
Bypass Notification
Disarm
2
System disarmed
Disarm
4
System disarmed with
Tamper Alert
Disarm
5
System disarmed
NPC® active
© 2003 directed electronics, inc.
37
➜ table of zones
A zone is represented by the number of LED flashes used by the
system to identify a particular type of input. Standard input
assignments are listed in the following table, along with spaces to
write in any optional sensors or switches that you have had
installed.
ZONE
(Number of
LED Flashes)
DESCRIPTION
1
Instant trigger for optional
hood or trunk pins
2
A heavier impact detected by
the Shock Sensor
3
Door switch trigger
5
Ignition trigger
DEALER-INSTALLED
OPTIONS
note: The LED does not report when the Warn Away®
response has been activated; it only reports Triggered
Sequences.
➜ nuisance prevention circuitry
Your security system has Nuisance Prevention Circuitry™
(NPC™) to prevent annoying false alarms. This prevents repetitive trigger sequences due to faulty door pinswitches or environmental conditions such as thunder, jackhammers, airport
noise, etc.
Here's how it works: If the alarm is triggered by the same sensor
or switch three times within a 60 minute period, your system
38
© 2003 directed electronics, inc.
interprets this pattern of triggers as false alarms. After the third
trigger, the NPC™ ignores, or bypasses, that sensor or switch
(along with any other sensors or switches sharing the same zone)
for 60 minutes. If the bypassed sensor is triggered again while it
is already being bypassed, the 60-minute bypass period will start
over. This ensures that a sensor that is continually being triggered will remain bypassed.
The vehicle doors are protected differently by NPC™. If your
security system is triggered by an open door for three, full 30second cycles (one and one half minutes), the system will bypass
the doors until the trigger ceases.
note: Arming and disarming the system does not reset the
NPC™. The only ways to reset a bypassed zone are for
that zone not to be triggered for 60 minutes or to turn the
ignition key on. When testing your system, it is important to remember that NPC™ can cause zones to be
bypassed and appear to not work. If five chirps are heard
when disarming the system, NPC™ has been engaged.
To clear the NPC™ memory, simply turn the ignition
key on.
© 2003 directed electronics, inc.
39
code hopping ™ re-synchronize
If the transmitter is pressed many times out of range, or the
battery is removed, the transmitter may get temporarily out of
synchronization and fail to operate the system. To synchronize
he transmitter, simply press
several times within range of
the vehicle. The system will automatically synchronize and the
transmitter will respond normally.
troubleshooting
➤
Door input does not immediately trigger full alarm. Instead,
first I hear chirps for 3 seconds:
That's how the progressive two-stage door input works! This is
a feature of this system. This is an instant trigger, remember,
since even if the door is instantly re-closed, the progression from
chirps to constant siren will continue.
➤
Closing the door triggers the system, but opening the door
does not:
Have you correctly identified the type of door switch system?
This often happens when the wrong door input has been used.
(See H1/5 GREEN Door Trigger Input, Primary Harness Wire
Connection Guide section of this guide.)
➤
System will not passively arm until it is remotely armed and
then disarmed:
40
© 2003 directed electronics, inc.
Are the door inputs connected? Is the H1/6 blue wire connected
to the door trigger wire in the vehicle? Either the H1/5 green or
the H1/7 violet should be used instead. (See Primary Harness
Wire Connection Guide section of this guide.)
➤
Door input does not respond with the progressive trigger,
but with immediate full alarm:
Does the Status LED indicate that the trigger was caused by the
shock sensor? (See Table of Zones section of this guide.) The
shock sensor, if set to extreme sensitivity, may be detecting the
door unlatching before the door switch sends its signal.
Reducing the sensitivity can solve this problem.
➤
The Valet®/Program switch doesn't work.
Is it plugged into the correct socket? (See Plug-In LED and
Valet®/Program/Program Switch section of this guide.)
➤
Status LED doesn't work.
Is the LED plugged into the correct socket? (See Plug-In LED
and Valet®/Program Switch section of this guide.)
© 2003 directed electronics, inc.
41
glossary of terms
Control Module: The "brain" of your security system. Usually
hidden underneath the dash area of the vehicle. It houses the
microprocessor that monitors your vehicle and controls all of
the security system’s functions.
Failsafe ® Starter Kill Relay: Located on-board the control
module, this is an automatic switch controlled by the security
system that prevents the vehicle's starter from cranking whenever the system is armed. The vehicle is never prevented from
cranking when the system is disarmed, in Valet Mode, or if the
starter kill fails.
Input: Any physical connection to the security system. An input
can be provided through a sensor, pinswitch or by existing
systems in the vehicle, such as ignition or courtesy lights.
LED: A red light mounted inside the vehicle, at a location determined by the installer. The LED indicates the status of your
system and also reports triggers and faults in the system or
sensors.
Shock Sensor: A dual-stage shock sensor, located on-board the
control module, that detects impacts to the vehicle.
Siren: A noise generating device, usually installed in the engine
compartment of the vehicle. The siren generates the chirps and
tones heard when the system is triggered.
42
© 2003 directed electronics, inc.
Transmitter: A hand-held, remote control that operates the
various functions of the security system.
Trigger or Triggered Sequence: The "setting off" or "tripping"
of the alarm. A Triggered Sequence consists of the siren sounding
and the parking lights flashing for 30 seconds.
Valet®/Program Switch: A small, push-button switch mounted
inside the vehicle, at a location determined by the installer. This
switch is used to override the alarm when a transmitter is lost or
damaged, or can be used to put the system into Valet Mode.
Warn Away Response: Light impacts to the vehicle generate the
Warn Away Response, which consists of several seconds of siren
chirps and flashing parking lights.
Zone: A zone is a separate input that the alarm recognizes as
unique. Each input to the system is connected to a particular
zone. Two or more inputs may share the same zone.
© 2003 directed electronics, inc.
43
security & convenience expansions
Listed below are some of the many expansion options available
for use with your system. Some options may require additional
parts and/or labor. Please consult with your dealer for a complete
list of options available for use with this system.
Audio Sensor: Metal on glass, glass cracking, and breaking glass
produce distinctive acoustic signatures. The 506T audio sensor
uses a microphone to detect these sounds, and then analyzes
them with proprietary acoustic software to determine if the glass
has been tampered with or broken.
Backup Battery: The 520T Backup Battery ensures that the
system stays armed, triggers the alarm and keeps the optional
starter kill active if main battery power is disconnected.
Field Disturbance Sensor: An invisible dome of coverage is
established by the 508D "radar" sensor. Your security system will
respond to any intrusions into this field by initiating the triggered sequence.
Power Trunk Release: The
output of the system can operate
a factory power release for the vehicle's trunk or hatch. An
optional relay is required. If the factory release is not power-activated, then Directed Electronics' 522T trunk release solenoid
can be added in most cases.
44
© 2003 directed electronics, inc.
Power Window Control: Automatic power window control is
provided with the 529T and 530T systems. These options
operate power windows, by rolling them up, down, or both up
and down. The 530T also offers one-touch switch operation.
Valet™ Start System: For the ultimate in convenience, the Valet
Start System can start your vehicle, monitor engine functions
and activate your climate control system with a push of a button!
Over-rev protection, open-hood lockout, brake pedal shutoff
and automatic timer shutoff are included. (This option is available only for fuel-injected, automatic-transmission vehicles.)
© 2003 directed electronics, inc.
45
wiring quick reference diagram
46
© 2003 directed electronics, inc.
notes
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
© 2003 directed electronics, inc.
47
48
© 2003 directed electronics, inc.
✂
✂
To arm the system using your remote
■ Pressing
for one second will arm the system. The parking lights
will flash once and the siren will chirp once.
To disarm the system using your remote
■ To disarm the system, press
for one second. The parking lights will
flash twice and the siren will chirp twice to confirm the system is disarmed.
To enter panic mode using your remote
■ Press
for 1.5 seconds. The parking lights will flash and the siren
will sound for 30 seconds.
✂
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
QUICK REFERENCE GUIDE:
QUICK REFERENCE GUIDE:
To arm the system using your remote
■ Pressing
for one second will arm the system. The parking lights
will flash once to confirm the doors are locked.
To disarm the system using your remote
■ To disarm the system, press
for one second. The parking lights will
flash twice to confirm the system is disarmed.
To enter panic mode using your remote
■ Press
for 1.5 seconds. The parking lights will flash and the siren
will sound for 30 seconds.
50
© 2003 directed electronics, inc.
© 2003 directed electronics, inc.
51
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed Electronics has had one purpose, to provide consumers with
the finest vehicle security and car stereo products and accessories available. The recipient of
nearly 100 patents and Innovations Awards in the field of advanced electronic
technology, DIRECTED is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed Electronics is committed to delivering world class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
www.directed.com
© 2003 Directed Electronics, Inc. - All rights reserved
G322R 7-03
Download PDF