Casablanca Brescia Owner`s manual

Casablanca Brescia Owner`s manual
OWNER’S MANUAL
GENERAL
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OUTSIDE USA (EXCLUDING MODELS ENDING IN ‘E’) FAN INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CONTROL FEATURES:
3-SPEED OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INTELI•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VERSA•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
COMFORT•TOUCH OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electrician should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged
in any way. Contact Casablanca Fan Company
by calling 1-888-227-2178, or contact your
local authorized Casablanca dealer for
assistance in obtaining service.
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
18†
70†
84†
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
P/N 1943610 REV.D
CAUTION: MOUNT WITH THE LOWEST MOVING
PARTS AT LEAST 2.5 METRES ABOVE FLOOR OR
GRADE LEVEL.
ATTENTION: INSTALLER DE SORTE QUELES
PIÈCES INFÉRIEURES SOIENT À AU MOINS 2.5
MÈTRES AU-DESSUS DU PLANCHER OU DU SOL.
P/D OCT99PDG
3
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting
recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7' above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18" from the wall in order to provide
sufficient clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• In low ceiling locations, our optional Low Ceiling Adaptor (LCA—available at
extra cost) can be used to gain 31⁄2" on certain fan models.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined with
corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in
smaller rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
Pole Length
8'
Standard
8' 6"
Standard
9'
6"
12"
9' 6"
12"
10'
18"
11'
24"
12'
36"
13'
48"
14'
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing on
high (cathedral) ceilings or sloped
ceilings. Casablanca offers standard poles
in increments of 6" up to 5'. Custom poles
are available in lengths up to 10'. See your
Authorized Casablanca Dealer for details.
NOTE: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Calculation of 32
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
4
EXTENSION
POLE
MAXIMUM
HANG-TRU®
ANGLE 32º
32°
BLADES MUST BE A
MINIMUM OF 7¢
ABOVE THE FLOOR
7¢MINIMUM
EXAMPLE 1
This slope is less than 32˚.
It is OK to install your fan.
EXAMPLE 2
This slope is 32˚. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32˚.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards
to purchasing a “Slope Ceiling Adaptor.”
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan,
remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging
material, be certain that all parts have been removed.
NOTE: Only one set of blade holders is supplied. Depending on the fan model and series they will be either the
Commodore Style, the Center Style, the Badge Style with
matching badges, or the Standard Style blade holder.
PERMA•LOCK™ HARDWARE
LOCKING BOLT
(MOTOR COUPLING)
DOWNROD & BALL
ASSEMBLY
FAN PREPARATION
IMPORTANT SAFETY INFORMATION!
BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN,
INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND
LOCK THE ASSEMBLY
GROUND
WIRE
MOTOR
WIRES
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
DOWNROD
&
BALL
ASSEMBLY
TAPERED
THREAD
Step B. Thread the downrod into the motor coupling until it
stops turning, this will take at least four and a half full turns.
Step C. Securely tighten the locking bolt to ensure safe operation of your fan.
LOCKING
BOLT
MOTOR
COUPLING
CAUTION: Failure to fully lock in the downrod before securely tightening the locking
bolt may cause the fan to separate from the
downrod during normal operation!
CEILING HARDWARE
ADDITIONAL HARDWARE
CROSSBAR
MOUNTING
BRACKET
2 1/4† x 8-32 ROUND HEAD
SCREWS (2)
WIRE NUT (4)
1† x 8-32 ROUND
HEAD SCREWS (2)
FLAT WASHER (2)
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting
hardware provided with the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit breaker
or fuse box), lower the old fixture and disconnect the wiring.
Check the ceiling fixture outlet box to be sure that it is
marked ‘Approved for ceiling fan mounting’. If it is not, a new
box must be installed.
5
CROSSBAR MOUNTING BRACKET INSTALLATION
NOTE: FOR INSTALLATION OUTSIDE USA (EXCEPT MODELS
ENDING IN ‘E’) USE THE HANGING INSTRUCTIONS ON CEILING FAN
APPROVED
PAGE 8.
WIRING BOX
Proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through
the crossbar mounting bracket center hole. Attach the bracket,
with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet
box.
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
CEILING
WIRING
RIDGE
SIDE
DOWN
CROSSBAR
MOUNTING
BRACKET
FLAT
WASHER
CAUTION: To reduce the risk of
personal injury, use only the
mounting hardware provided with
the approved outlet box to install
the crossbar mounting bracket.
GREEN
GROUND
WIRE
APPROVED
OUTLET BOX
HARDWARE
CANOPY HARDWARE
CANOPY SCREW (4)
CANOPY LOCK WASHER (4)
CANOPY
HATCH
CANOPY
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1/4† long
canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
NOTE: On sloped ceilings, align the
canopy opening towards the top or
room peak.
CROSSBAR
MOUNTING
BRACKET
CANOPY
CANOPY LOCK
WASHER
CANOPY
SCREW
6
HANGING THE FAN
Step 3. To hang the fan body in the
canopy, hold the fan body firmly and insert the ball into the canopy opening.
Check that no wires were pinched. Rotate the fan body until the slot in the
nylon ball fits into the pin opposite the
canopy opening.
NOTE: Independent control of the
light fixture using a W-8 requires an
additional power wire run from the
wall switch to the fan. See Page 10
for wiring.
CAPPED
BLUE
D1-OPTION
WIRE ON
3-SPEED ONLY
FOR INDEPENDENT
W-8 LIGHT
CONTROL
BALL
SLOT
PIN
CANOPY ELECTRICAL CONNECTIONS
PULL CHAIN OR
W-4 CONNECTIONS
WIRE NUT
Step 4a. Attach the fan wires to the ceiling fixture outlet
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
2 BLACK & BLUE
D1-OPTION WIRES
(WITHOUT W-8)
Step 4b. Pull Chain or W-4 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLUE wire and BLACK power wire from fan to BLACK power
wire in ceiling outlet box. Secure with wire nut.
2 WHITE WIRES
3 GREEN WIRES
Step 4c. W-8 Wiring Connections
• GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to RED wire from W-8 in ceiling outlet box. Secure with wire nut.
• BLUE wire from fan to YELLOW wire from W-8 in ceiling
outlet box. Secure with wire nut.
W-8 CONNECTIONS
BLUE & YELLOW
WIRES
BLACK & RED
WIRES
2 WHITE WIRES
NOTE: See Page 10 for additional wiring information.
3 GREEN WIRES
CANOPY HATCH INSTALLATION
Step 5. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 6. Install canopy hatch with the last
canopy screw and lock washer. To do this,
tilt the fan body away from the hatch
opening.
Tighten the screws firmly by hand only,
Step 7. Straighten the fan, then check
to ensure that there is no movement between the canopy and ceiling or Hang-Tru
ball and top support shaft.
CANOPY
HATCH
LOCK
WASHER
CANOPY
SCREW
TILT THE
FAN TO
INSTALL
LAST
CANOPY
SCREW
7
BEFORE INSTALLING THE BLADE HOLDERS & BLADES
Step 8. Check your fan and identify if it is a Direct Drive or XLP Motor.
DIRECT
DRIVE
MOTOR
XLP MOTOR
BLADE
PAIRS OF
BLADE
HOLDER
HOLES
THREADED
DIRECTLY
INTO THE
MOTOR
BLADE
HOLDER
USE
ROUND
HOLES
FOR 5
BLADES
BLADE
BLADE
HOLDER
SWITCH
HOUSING
FLYWHEEL
Direct Drive
Blade holders attach directly to the motor unit.
SWITCH
HOUSING
XLP Motor
Blade holders attach to a flexible flywheel.
BLADE HOLDERS & HARDWARE
COMMODORE STYLE
BLADE SCREW
(3 PER BLADE)
CUP WASHER
CENTER STYLE
BLADE HOLDER SCREW
(2 PER BLADE)
BLADE SCREW
(4 PER BLADE)
STEEL WASHER
BADGE STYLE
BADGE
BLADE HOLDER SCREW
(2 PER BLADE)
BLADE SCREW
(4 PER BLADE)
STANDARD STYLE
BLADE HOLDER SCREW
(2 PER BLADE)
BLADE SCREW
(3 PER BLADE)
FIBER WASHER (NOT
INCLUDED IN DAMP
LOCATION FANS)
COMM0DORE BLADE HOLDER & BLADE INSTALLATION
Step 8a. Commodore Post Style
Attach the blades to the blade holders
with the three countersunk blade
screws and cup washers provided for
each blade.
Hand tighten securely.
BLADE SCREW
(3 PER BLADE)
BLADE HOLDER
INDENTATION
Insert the blade holder shaft into the
motor flywheel so that the notch lines
up with the brass blade holder screw.
Hand tighten securely.
MOTOR
FLYWHEEL
BRASS BLADE HOLDER SCREW
(1 PER BLADE HOLDER)
8
CUP WASHER
(3 PER BLADE)
CENTER STYLE BLADE HOLDER & BLADE
Step 8b. Center Style
Attach the blades to the
blade holders with the four
blade screws and steel
washers provided for each
blade.
Hand tighten securely.
BLADE SCREW
(4 PER BLADE)
STEEL WASHER
(4 PER BLADE)
Install the assembled blade
and blade holder to the flywheel (round holes) or direct
drive motor.
Hand tighten securely.
Repeat for each assembly.
BLADE HOLDER SCREW
(2 PER BLADE HOLDER)
BADGE STYLE BLADE HOLDER & BLADE
BLADE SCREW
(4 PER BLADE)
Step 8c. Badge Style
Attach the blades to the blade
holders by first pressing the blade
badge into the blade, then installing the blade holder using the
four blade screws provided for
each blade.
Hand tighten securely.
Install the assembled blade and
blade holder to the flywheel
(round holes) or direct drive motor.
Hand tighten securely.
BADGE STYLE
BLADE HOLDER
BLADE HOLDER SCREW
(2 PER BLADE HOLDER)
BLADE
BADGE
Repeat for each assembly.
BLADE
CLASSIC STYLE BLADE HOLDER & BLADE
Step 8d. Classic Style
Attach the blades to the blade
holders with the three blade screws
and felt washers provided for each
blade.
Hand tighten securely.
BLADE SCREW
(3 PER BLADE)
BLADE HOLDER
SCREW
(2 PER BLADE
HOLDER)
FELT WASHER
(3 PER BLADE)
Install the assembled blade and
blade holder to the flywheel (round
holes) or direct drive motor.
Hand tighten securely.
Repeat for each assembly.
BLADE
WARNING: To reduce the risk of personal injury, do not bend blade holders when installing,
balancing, or cleaning. Do not insert foreign objects between rotating fan blades.
PROCEED TO YOUR FAN’S CONTROL FEATURE SECTION FOR INSTALLATION/OPERATING INSTRUCTIONS:
3-SPEED - PAGE 12 | INTELI•TOUCH - PAGE 14 | VERSA•TOUCH - PAGE 17 | COMFORT•TOUCH - PAGE 19
9
FAN INSTALLATION OUTSIDE THE USA - EXCLUDING MODELS ENDING IN ‘E’
If you do not have an existing fixture located where you wish to place your Casablanca fan, a new ceiling fixture outlet box
must be installed (use an outlet box marked acceptable for fan support) and an electrical cable to run it. This box must be
secured to the ceiling according to the outlet box manufacturer’s instructions. It is recommended that this be done by
a qualified electrician.
Vaulted or Cathedral Ceiling Installations
Your Casablanca fan may be installed on a vaulted or cathedral ceiling in the same manner as described for a flat ceiling. The
Hang-Tru® mounting system makes it possible to hang your fan on sloped ceilings up to a 32 angle.
Using Existing Ceiling Fixture Outlet Box
After turning electrical power off, lower the old fixture to expose the wiring and the ceiling fixture outlet box. Cut the
fixture wires or if wire nuts have been used, unscrew them and disconnect the wires. The fixture can then be removed.
After removing the old fixture, check the outlet box to sure that it is supported by a joist or beam across its upper surface.
If not, a 2" x 4" stud must be installed.
OUTSIDE USA - SECONDARY SUPPORT INSTALLATION PARTS
OUTLET
ADAPTOR
PLATE
6" OUTLET BOX
CABLE
3
⁄8"- 7 LAG SCREW (5")
FENDER
WASHER
SPRING LOCK
HOOK
OUTSIDE USA - MOUNTING SECONDARY SUPPORT PARTS TO OUTLET BOX
JOIST
OR
BEAM
WARNING: MOUNT ONLY TO AN OUTLET BOX
MARKED ACCEPTABLE FOR FAN SUPPORT
••••
ADVERTISSEMENT: ASSEMBLER UNIQUEMENT À
UNE BÔITE DE SORTIE JUGÉE ACCEPTABLE POUR
RETENIR UN VENTILATEUR.
Step 1. Remove the knockout plug in the center of the outlet box or drill a 1/2† hole for the lag screw to pass through.
Then drill a 1/4† guide hole into the joist or beam to a depth
of 3 inches.
Step 2. Route the outlet box wires through the 1/2† diameter
outer hole of the outlet adaptor plate.
Step 3. Line up the slotted holes and four canopy screw
holes in the crossbar mounting bracket and outlet adaptor
plate with the 8-32 mounting holes in the outlet box. Install
the two 8-32 X 2 1/4† (1†) screws and flat washers in fan
hardware kit and tighten securely by hand only!
Step 4. With fender washer and outlet box cable attached as
shown, pass lag screw through center hole of outlet adaptor
plate and screw into pre drilled 1/4†guide hole of joist. Tighten
until outlet box is firmly mounted.
TIP: Threading two of the canopy screws into the
crossbar mounting bracket will help everything stay
aligned as you tighten the lag screw. Remove them
before starting Step 5.
1
⁄4" GUIDE
HOLE
CROSSBAR
MOUNTING
BRACKET
1
⁄2"
HOLE
OUTLET
ADAPTOR
PLATE
8-32 X 21⁄4"
(1") SCREW
6" OUTLET BOX
CABLE
10
OUTLET
BOX
LAG
SCREW
FENDER
WASHER
OUTSIDE USA - SECONDARY SUPPORT ♦ CANOPY INSTALLATION
Step 5. Attach the canopy to the crossbar mounting bracket behind the
installed outlet adaptor plate with three of the 8-32 x 2 1/2† long canopy
screws and lock washers provided with your Casablanca fan. Hand tighten
until snug against the ceiling.
Note: On sloped ceilings, align the canopy opening toward the top or peak
of the room.
FAN
CABLE
Step 6. Attach the spring
lock hook to the fan cable
by depressing the spring
lock and clipping onto the
loop at the end.
SPRING
LOCK
CANOPY
LOCK
WASHER
FEED OUTLET BOX
CABLE AND OUTLET
BOX WIRES THROUGH
CANOPY OPENING
SPRING
LOCK HOOK
CANOPY
SCREW
OUTSIDE USA - SECONDARY SUPPORT ♦ HANGING THE FAN
Step 7. To hang the fan body in the canopy, hold the fan
body firmly and insert the nylon ball into the canopy opening. Rotate fan body until slot on nylon ball fits into pin
opposite canopy opening.
Step 8. Attach the fan wires to the ceiling outlet box wiring
by twisting the bare ends of the wiring together:
• White wire from fan to white NEUTRAL wire in ceiling outlet box.
• Black wire and blue wire (3-Speed fan only) from fan to
black (or red) POWER wire in ceiling outlet box.
• Green leads from crossbar mounting bracket and fan to
grounding conductor of power source.
Secure by threading on the wire nuts provided with the fan.
OUTLET
BOX
CABLE
CANOPY
FAN
CABLE
PIN
BALL
SLOT
OUTSIDE USA - SECONDARY SUPPORT ♦ COMPLETING INSTALLATION
Step 9. Attach the fan cable to outlet box cable with the
spring lock hook. Make sure the spring lock is tightly closed.
Step 10. Tuck the wires into the canopy with the wire nuts
pointed upward, so that the white and black wires are on
opposite sides of the canopy and all wires are clear of the
canopy opening. Tuck the extra cable and screw lock hook
into the canopy.
NOTE: International fans and light fixtures are supplied
with plug and socket connectors. Substitute these connectors
for the wire nuts shown throughout this manual.
WIRE NUTS
INSTALLED
FAN AND
OUTLET
CABLES
SECURED BY
SPRING
LOCK HOOK
RETURN TO YOUR FAN INSTALLATION INSTRUCTIONS AND
CONTINUE WITH THE ‘CANOPY HATCH INSTALLATION’
SECTION ON PAGE 7.
11
3-SPEED
3-SPEED ♦ W-4 WALL CONTROL OF THE FAN
• The W-4 allows the choice of four (4)
different speed settings.
• No light fixture is used.
• Set the FAN pull chain switch to the
HIGH speed setting.
• No changes in household or fan wiring
are required.
• The fan may be turned ON and OFF by
the W-4 wall control.
CAUTION! Failure to set the pull-chain
speed to HIGH can result in faulty
operation of the fan and damage to
the W-4 wall control. To confirm fan
is set to HIGH: Turn W-4 fan speed
switch to 'HI' - set fastest fan speed
with pull chain.
R
3-SPEED ♦ W-8 WALL CONTROL OF THE FAN & LIGHT(S)
• The fan may be turned ON and OFF
by the W-8 wall control.
• The lights may be turned ON and
OFF by the W-8 and the intensity
adjusted from low to high.
• The fan must be supplied with two
independent 120V AC supply
wires.
• Set the FAN pull chain switch to
the HIGH speed setting.
• Turn the lights ON at the fan.
• The W-8 allows the choice of four
(4) different speed settings.
CAUTION! Failure to set the pullchain speed to HIGH can result in
faulty operation of the fan and
damage to the W-8 wall control.
To confirm fan is set to HIGH: Turn
W-8 fan speed switch to 'HI' - set
fastest fan speed with pull chain.
12
3-SPEED
3-SPEED ♦ OPERATION
Pull-chain switches on the fan control the fan and lights.
Using the fan control pull-chain switch: Fan off at start.
First pull: fan ON, low speed
Second pull: medium speed
Third pull: high speed
Fourth pull: fan OFF
Using the optional light pull-chain switch: Light off at start.
First pull: light ON
Second pull: light OFF
Direction of blade rotation is controlled by the reverse slide
switch on the side of the switch housing.
No changes in household wiring are required.
OPTIONAL LIGHT
PULL CHAIN
SWITCH
FAN & SPEED
CONTROL
PULL CHAIN SWITCH
REVERSE
SWITCH
3-SPEED ♦ OPTIONAL LIGHT FIXTURE INSTALLATION
NOTE: If a separate circuit is used to control the lights from a wall
control, the BLUE D1-Option wire in the canopy should be connected
to that switch leg with the BLACK fan power wire.
1. Refer to light kit instructions to assemble and attach your light
kit correctly.
2. Remove the two 8-32 screws from the switch housing cap.
3. Remove the plug from switch housing.
4. Install pull-chain switch and finger tighten collar on switch.
5. Connect one wire from pull-chain switch to the BLUE D1-Option
wire. Secure splice with a wire nut.
6. Connect other wire from pull-chain switch to BLACK wire from
light kit. Secure splice with a wire nut.
7. Connect WHITE wire from switch housing to WHITE wire from light
kit. Secure splice with a wire nut.
8. At the canopy, connect the BLACK and BLUE wires.
SWITCH
HOUSING
COLLAR
3-SPEED ♦ OPTIONAL WALL CONTROL ♦ W-4
The W-4 wall control provides four-speed control of fan from a convenient wall location. The
W-4 is designed to replace a standard wall switch and will fit wall boxes with a depth of 2"
or greater. Not for use with single pull-chain fan/light option wiring.
To install a W-4 wall control in place of an existing wall switch, follow the instructions on
the W-4 package.
Note: No rewiring is required if the fan is replacing an existing light fixture.
Operation of the fan from the wall switch is simple:
1. Turn knob to obtain desired speed setting.
R
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-4 wall control. To confirm fan is set to HIGH: Turn W-4 fan
speed switch to 'HI' - set fastest fan speed with pull chain.
3-SPEED ♦ OPTIONAL WALL CONTROL ♦ W-8
The W-8 wall control provides separate control of fan and light with two separate knobs from
a convenient wall location. The W-8 is designed to replace a standard wall switch and wall
boxes with a depth of 2" or greater. Requires two hot leads from wall box to ceiling wiring
box.
To install a W-8 wall control in place of an existing wall switch, follow the instructions on
the W-8 package.
Operation of the fan from the wall switch is simple:
1. Turn the upper knob to the desired fan speed.
2. Turn the lower knob to the desired light setting.
LO
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of
the fan and damage to the W-8 wall control. To confirm fan is set to HIGH: Turn W-8 fan
speed switch to 'HI' - set fastest fan speed with pull chain.
13
R
INTELI•TOUCH © INSTALLING THE W-32 WALL CONTROL
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the
following precautions must be observed:
1. Use only the Casablanca W-32 wall control.
3. Do not use more than one fan per wall control.
2. Do not use any additional control with your Inteli-Touch 4. No other light fixtures or electrical appliances may be confan (for example, dimmer, fan speed control, etc.).
nected on the circuit controlled by the W-32 wall control.
INTELI•TOUCH ♦ SINGLE W-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
W-32 is used to describe either white (-11) or ivory finish.
1. Remove the screws and switch plate from the existing
switch box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the
wire connections.
4. Remove the two wires from the switch.
5. Connect the two wires just removed from the switch to
the W-32 wall control black wire and black/white stripe
wire. Secure these connections with wire nuts.
6. Install the W-32 in the wall box with the two long screws
provided.
7. Install the wall plate with the two color matched screws.
NOTE: If your wall control operation is reversed, i.e., fan switch
controls lights and light switch controls fan, simply swap the
two W-32 black/white stripe wires.
SWAP THESE
TWO WIRES WHEN
NECESSARY
(SEE NOTE)
R
INTELI•TOUCH ♦ DUAL W-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
To control the fan and lights from two locations (a threeway circuit), use 2 W-32 wall controls.
1. Remove the screws and switch plate from the existing switch box and the screws holding the switch in
the switch box.
2. Pull the existing switch from the switch box to expose the wire connections.
3. Determine which wire is connected to the common
terminal of the 3-way switch. (The terminal will be
marked on switch).
4. Remove the wire from the common terminal of the
3-way switch. Connect this wire to the remaining
black/white striped wire on the W-32 control. Secure
this splice with a wire nut.
5. Remove the two remaining wires from the 3-way
switch. Connect one of these wires to a black wire
on the W-32 control. Secure the splice with a wire
nut. The remaining wire is to be connected to the
other black wire on the W-32. Secure the splice with
a wire nut.
6. Install the W-32 in the wall box with the two long
screws provided.
7. Install the wall plate with the two short colormatched screws provided.
8. Installation of the second W-32 control is identical.
Repeat steps 1 through 7.
14
SWAP THESE TWO WIRES
WHEN NECESSARY
(SEE NOTE BELOW)
R
R
END
OF
LINE
IN
LINE
NOTE: If your wall control operation is reversed, i.e., fan switch
controls lights and light switch controls fan, simply swap the
two W-32 black/white stripe wires.
R
INTELI•TOUCH OPERATION ♦ POWER
The
button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light level.
INTELI•TOUCH OPERATION ♦ SPEED CONTROL
There are six individual speed settings for the fan; each speed is indicated by
an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled
. The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the
button is used. To maintain this level of speed,
turn the fan on by pressing
less than one second. To lower speed,
turn fan off, then on by pressing and holding the
button until the
desired speed is reached. When the fan is on, you may increase the speed by
button until the desired speed is reached,
pressing and holding the
then release it.
FAN CONTROL
ON - OFF
R
A momentary press
of the FAN button
TO CHANGE SPEED
Press and hold FAN
button longer than
one second
INTELI•TOUCH OPERATION ♦ REVERSING AIRFLOW
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
1. Make sure the
is on.
2. Press the
button.
Note: A four-toned signal indicates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
INTELI•TOUCH OPERATION ♦ LIGHT
button for less
To turn the lights off and on, press and release the
than one second.
To vary the light brightness:
1. With lights off, press and hold the
button. After one second
the lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the
button is used. To
maintain this level of brightness, press the
button for less than
one second. To lower the brightness, turn the lights off, then press and hold
the
button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
the
button until the desired level is reached, then release it.
LIGHT CONTROL
ON - OFF
A momentary press of
the LIGHT button
R
TO CHANGE BRIGHTNESS
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully
demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn
off for at least three seconds. This will
clear the fan memory ready for programming.
2. Turn
on.
3. Immediately operate the buttons in the following sequence:
FAN
- LIGHT
+
-
+
FAN
- LIGHT -
+
+
FAN
A multi-tone signal will verify the start of the test program
which proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short
time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will
continue to repeat until the
is turned off for more
than three seconds, cancelling the program.
15
R
INTELI•TOUCH OPERATION ♦ LIGHT-MINDER® PROGRAM
The Light-Minder program automatically turns OFF the fan mounted lights after
two hours.
To enter the Light-Minder Program:
1. Turn the
OFF for at least three seconds.
2. Turn the
ON.
3. Immediately operate the buttons in the following sequence:
+
+
+
4. A series of tones indicates this command has been accepted.
The fan and light will operate normally using the buttons to turn them on and off.
But, if the lights are left on, they will automatically shut off after two hours. To
cancel the Light-Minder Program, turn the
off for three seconds.
INTELI•TOUCH OPERATION ♦ SAFE-EXIT® PROGRAM
The Safe-Exit Program gives you about thirty seconds of light when you turn
the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
1. Turn the
off for at least three seconds.
2. Turn the
on.
3. Immediately operate the buttons in the following sequence:
+
+
+
After you hear the confirming audio
tones from the fan - immediately press
4. The lights will blink to indicate this command has been accepted.
The lights will stay on for twenty seconds and then begin to dim. After a
total of thirty seconds has elapsed, the lights will be off completely. To
cancel the Safe-Exit Program, turn the
off for three seconds.
Note: Both Light-Minder and Safe-Exit
programs can run at the same time,
however the dimmer cannot be used,
the light may only be turned ON/OFF.
INTELI•TOUCH OPERATION ♦ HOME-SAFE® PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
1. Turn the
off for at least three seconds.
2. Turn the
on.
3. Immediately operate the buttons in the following sequence:
+
+
+
4. A tone and flashing light indicate this command has been accepted.
This program overrides all manual control of lights and fan. The lights will now be
automatically cycled on and off in a controlled sequence as follows: On 1 hour, off
1
/2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of
lighting is seen each day of the week.
To cancel the Home-Safe Program, turn the
off for three seconds.
INTELI•TOUCH OPERATION ♦ FAN-MINDER™ PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
1. Turn the
off for at least three seconds.
2. Turn the
on.
3. Immediately operate the buttons in the following sequence:
+
+
+
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan
will reduce one speed for each two-hour interval. The fan will not, however, descend below the
second lowest speed.
To cancel the Fan-Minder Program, turn the
off for three seconds. You may increase the fan
speed by pressing and holding the
button until the desired speed is reached, then release it.
The fan will again reduce one speed for each 2 hour interval.
16
VERSA•TOUCH ♦ INSTALLATION
W-42
CONTROL
HOLDER
W-42
CONTROL
DRYWALL
ANCHOR
6-32 (2)
9V BATTERY
SCREW
6-32 X 3/8”
(2)
WOOD
SCREW
1” (2)
SCREW
6-32 X 1”
(2)
VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION
CAUTION! DO NOT USE WITH WALL DIMMER.
STANDARD
TOGGLE
SWITCH
INNER
MOUNTING
HOLES
REMOVE TABS
ROCKER
TYPE
LIGHT
SWITCH
OUTER
MOUNTING
HOLES
SWITCH
COVER
PLATE
SWITCH
COVER
PLATE
CONTROL
HOLDER
Standard Light Switch
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up the
two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
Rocker Light Switch
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate.
Do not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two
outer mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
VERSA•TOUCH ♦ HOLDER INSTALLATION / STORAGE
Wall Installation
Step 1. Locate a
2x4 wall stud in a
convenient location.
Step 2. Orient the
control holder as
shown over the
2x4 stud.
Step 3. Use the 1"
wood screws in either the inner or
outer mounting
holes. Install and
tighten screws by
hand only.
Note: The wall anchors and
6-32 x 1” screws may be used in
situations where mounting to a
stud is not possible. Use the inner
mounting holes. After securing the
anchor, discard the anchor’s
pointed screws and use the 6-32
decor ovalhead screws supplied.
Control Storage
Angle control in top first
until the unit can be
gently pushed back and
snapped into place.
TOP
GOES IN
FIRST
WOOD
SCREW 1”
ANCHOR
PANHEAD
SCREW
DRYWALL ANCHOR
DECOR OVALHEAD SCREW
6-32 X 1”
Removing Control
Gently Pull the lower edge
of the control out from the
holder.
VERSA•TOUCH ♦ BATTERY INSTALLATION
Remove Battery Door
Turn control on its front.
Twist a coin to unsnap
the door A. Lift door
away from control B and
remove C.
Changes or modifications not expressly approved in writing by Casablanca Fan Co. may
void the user’s authority to operate this
equipment.
SNAP PLUG
SOCKET
Install Battery
Press battery into
control aligned as
shown. Observe proper
polarity. Replace the
battery door.
GUIDE SLOTS
This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
17
VERSA•TOUCH OPERATION
R
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired speed.
LO
Low speed
MED Medium speed
HI
High speed
To turn off the fan. Press the FAN OFF
button.
Airflow Direction
To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is
on or off. The fan returns to its set speed after reversing.
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT button. Keep
pressing the button in excess of 0.7 seconds, it becomes a dimmer. The light varies from
‘bright’ to ‘dim’ over approximately 8 seconds. This sequence will reverse the light when it
reaches the brightest or dimmest level if you continue to hold the LIGHT button. Release the
button when the desired level is reached.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the
desired brightness level set previously.
SEND
SIGNAL
LED
R
VERSA•TOUCH ♦ CONFIRMING CHANNEL DIP SWITCH SETTING - CONTROL
Remote Setting
Step 1. Remove battery.
Step 2. Check that the dip
switch in the remote is set
to ‘01110’ - as shown.
Step 3. Check that the dip
switch in the fan is set the
same. (See section below
for fan dip switch location)
FIVE DIGIT DIP SWITCH
NOTE: All fans leave the factory set to ‘01110’.
VERSA•TOUCH ♦ CONFIRMING CHANNEL DIP SWITCH SETTING - FAN
NOTE: If this is the second Versa•Touch fan installed in the same
area, one of the fans MUST have its channel changed from ‘01110’ or
interference will occur. Make sure that the dip switch settings in both
the second remote and second fan are set to the same numbers.
DIP SWITCH
SET TO ‘01110’
DIP SWITCH
SET TO ‘01001’
Checking Fan Setting
Step 1. Remove the three motor cover screws and lift the motor
cover off. Through the view hole on top of the motor, locate the
dip switch.
Step 2. Check that the dip switch in the fan and the remote are
set to ‘01110’. If this is a second fan, change the dip switch
settings, making sure that the fan and remote are set to the
same number.
Step 3. Replace the cover and screws.
18
VIEW HOLE FOR
DIP SWITCH
W-21 MOUNTING PARTS
R
WALL BRACKET
ANCHOR (4)
REMOTE CONTROL
W-21
REMOTE CONTROL
WALL BRACKET
‘AAA’ ALKALINE
BATTERY (3)
WALL BRACKET
SCREW (4)
WALL BRACKET INSTALLATION
Installation of Remote Control
The wall mounting bracket for the remote control should be
located in a position that is approximately eye level. Secure
the wall mounting bracket with the 11/4† screws or anchors
provided, making sure it is level with the floor.
Mount control in convenient location
WALL
MOUNTING
BRACKET
CAUTION! DO NOT MOUNT REMOTE CONTROL ON OR NEAR
A METAL SURFACE - ERRATIC OPERATION WILL OCCUR.
Changes or modifications not expressly approved in writing
by Casablanca Fan Co. may void the user’s authority to operate this equipment.
•••
This device complies with RSS-210 of Industry Canada. Operation is subject ot the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Remove for handheld or tabletop use
BATTERY INSTALLATION
Battery Installation
Install three ‘AAA’ alkaline batteries in the sequence shown and
replace the battery compartment cover, then press the remote
control firmly to the wall bracket so that the Velcro® pads grip
the pads on the rear of the control. The remote control can be
easily removed at any time should you wish to use it in another
location. Just give the control a gentle tug to remove it.
REMEMBER THE REMOTE CONTROL WILL GO
BACK TO THE ORIGINAL FACTORY ‘PRESET CHANNEL’ NUMBER WHEN THE BATTERIES ARE
CHANGED. CHANGE CONTROL CHANNEL IF NECESSARY AFTER BATTERY REPLACEMENT.
PRESET CHANNEL #
-
+ -
+
+
-
SPACE
FOR
ROOM
LABEL
LOW BATTERY WARNING
Low Battery Indicator
The remote control warns of a low battery condition by displaying a rapidly flashing ‘Lo’
in place of the temperature display. When this occurs replace with fresh alkaline battery.
WARNING: Use of batteries other than non-leak sealed alkaline in the
remote control will void the warranty and can destroy the unit.
Note: When the remote is in the low battery mode the fan may not respond to
control commands correctly even though the fan may be running.
19
R
IMPORTANT OPERATING NOTES
Turning On Your Fan: The fan will not receive any signals
for the first 20 seconds after power on. This allows the
electronics to warm up and stabilize.
Power Failure: The remote control is not affected by household power failure as it is battery operated. Once power is
restored to the fan it will receive an auto-update signal from
the remote control within 30 minutes after power is restored.
All previously set modes and functions will be restored to
the fan.
Button Operation: Rapid button pressing causes erratic
fan operation. For reliable operation of the remote control
and fan you must wait ONE SECOND between button presses
to allow the radio signal to be transmitted to the fan and
received.
Labeling: If you have more than
one Comfort•Touch fan in your
home, we suggest you put an adhesive room identification label
on the back of the control. Labels are in the remote control
SPACE FOR LABEL
package.
General: Your Comfort•Touch remote control uses one of 15
different radio signals to control the fan. This channel is set at
the factory. There may be times when the channel needs to be
changed,i.e.:
• Two fans in the house set to the same causing interference.
• Two fans are to be operated from one control.
• Two controls are to operate the same fan - see special 'Dual
Remote Control' section on the next page.
TEST PROGRAM
Press the
button to activate a two minute program
that puts the fan through a complete functional test. The
test starts with a full screen display, then the 'preset' channel number before going into a full light, fan and reverse
exercise. Follow the remote control LCD display and compare it to the actual fan operation to confirm correct
operation.
FULL LCD
SCREEN
DISPLAY
W-21
TEMPERATURE
TEST
BUTTON
FAN OPERATION
The Comfort•Touch fan is controlled by the remote control.
The fan is turned on and off by alternate pushes of the large
right hand button. As with all button operations, an audio
tone sounds with each push. With the fan on, the control
display will indicate an up or down moving arrow that shows
direction and places a box around the operating speed. The
and
buttons below the fan button increase
two small
or decrease speed once for each press.
FAN
ON/OFF
BUTTON
SPEED
UP/DOWN
BUTTONS
R
AIRFLOW
DIRECTION
FAN SPEED
LIGHT OPERATION
The light is turned on and off by alternate pushes of the
large left hand button. When on, the display will indicate
the light bulb symbol and a vertical segment display representing brightness. When the light is on, the brightness may
be changed by using the small
and
buttons below the
light button. Pressing and holding either button will change
the brightness continuously.
Bulb-Saver Feature
When the light is turned on, the brightness is gradually increased until it reaches the preset level. This feature helps
extend light bulb life.
LIGHT
ON/OFF
BUTTON
LIGHT
UP/DOWN
BUTTONS
BRIGHTNESS
INDICATOR
ADDITIONAL CONTROL FEATURES
Additional control program features are available from the control panel by opening the control panel door. To activate a control
function press the appropriate button; the display will indicate
that the program is running.
In some cases you can run more than one program at once, such
as
and
and the display will indicate that they are
both activated. In other cases one program will override another
as the two programs can not run together i.e.
and
.
Full details are explained in the sections that follow.
20
CONTROL PANEL
DOOR
CONTROL
PANEL
REVERSE FEATURE
R
Pressing the
button will change the direction of rotation. An audio tone signals
the beginning of the reverse sequence and you will see the airflow direction arrow
changing. The fan gradually slows to a stop, then reverses direction.
Note: This function does not operate if the fan is not running.
REVERSE
AUTO-SPEED FEATURE
In the Auto Speed mode, fan speed changes in response to changes in room temperature. Push the
button to start. The words 'AUTO SPEED' show on the display. Set
the fan speed to the speed at which you are most comfortable. Once set, the fan will
increase or decrease by one speed for each 1.5 F increase or decrease in temperature.
If temperature decreases enough to turn the fan OFF, the Auto Speed indicator will
flash slowly to remind you that the fan will turn on when the temperature increases.
Note: The temperature displayed is from an electronic thermometer
built into the remote control that reads room temperature. It is not
a thermostat that controls the room temperature.
To cancel Auto Speed, simply push the
Selecting
also cancels Auto Speed.
AUTO SPEED
TEMPERATURE ACCURACY –3 F
button again.
SAVER FEATURE
The Saver mode will automatically turn lights off 1 hour after the
lights are turned on. Press the
button and 'SAVER' will appear in
the display. An audio tone will warn you 20 seconds before the probutton again to
gram is going to turn the lights off. Press the
cancel.
SAVER
WINTER FEATURE
The Winter mode provides draft-free recirculation of heated air. Press
to activate, and the word 'WINTER' is indicated. This puts the
fan in the upward airflow direction at the fan's lowest speed. Every ten
minutes the fan will increase to speed 3 for ten seconds before returning to the lowest speed.
Pressing any button on the remote will cancel the
'Winter' mode; except using the light functions.
WINTER
SECURITY FEATURE
Pressing the
button will start the Security lighting program. The controller beeps and indicates 'SECURITY'. The light
will automatically turn ON and OFF in a seemingly random manner over an eight and a quarter hour programmed cycle that is
designed to give the home a "lived-in" look.
Regardless of the light setting when switching to the Security
mode (lights on or off, dim or bright), the lights will increase
to high brightness and then begin the Security cycle. This cycle
is then repeated continuously until cancelled by pressing the
button.
At any time during the Security mode you may adjust the fan
speed, reverse the direction, operate in Auto Speed or Winter,
use Saver or run the Test mode without affecting Security mode.
You may still turn the light ON and OFF (or OFF and ON) manually for temporary lighting, but the light will continue to operate
automatically at its programmed times.
6
5
4
3
2
1
SECURITY
SECURITY
AUTO
SECURITY
REVERSE
SAVER
TEST
WINTER
Replace batteries when “Lo” is displayed
AUTO-SPEED: Thermostatic fan speed control
SECURITY: Lights ON and OFF automatically
REVERSE: Change airflow up or down
SAVER: Lights turn OFF after 1 hour
TEST: Tests all fan and light functions
WINTER: Draft-free heat recirculation
SECURITY MODE CYCLE
1. On for 30 minutes (80% bright)
2. Off for 30 minutes
3. On for 120 minutes (50% bright)
4. Off for 60 minutes
5. On for 60 minutes (100% bright)
6. Off for 120 minutes
7. On for 15 minutes (20% bright)
8. Off for 60 minutes
21
R
COMFORT•TOUCH ♦ CHANGING CHANNELS - CONTROL
Changing the control channel
1. Hold the
button down until a tone is heard.
2. The temperature display will show the current channel number.
3. Press fan up
or down
buttons to change the number to a
unique number from 49 to 63.
DO NOT use other channel numbers.
4. Push
to return to normal operation.
You will need to repeat this step any time you remove the remote
control batteries. Record the new channel setting in the space provided on the rear label.
REMOTE
CONTROL
CHANNEL
NUMBER
Note: Always change the remote control channel
first. The fan channel can only be changed by
having the desired channel already set in the remote control.
COMFORT•TOUCH ♦ CHANGING CHANNELS - FAN
1. Turn OFF power to the fan for five seconds or longer using the wall
switch or circuit breaker.
2. Turn the power back ON.
WAIT 20 SECONDS.
You have 90 seconds in which to complete step 3.
3. Press and hold the
and
buttons together until the
display shows 'cc' (for Change Channel), then release.
The control automatically changes the fan
channel to the new setting.
Do not reset the channel on other fans in
your home during this 110 second period.
COMFORT•TOUCH ♦ DUAL REMOTE CONTROL - BASE
A second remote control can be purchased from your dealer to provide
dual remote control of one fan. Because the fan could be confused by
two controllers signaling different information it is necessary to set a
BASE control and an AUXILIARY control.
The last control manually operated controls the fan.
Where two remote controls are used to control a single fan, they must
be set so that:
• BOTH controls are set to the SAME channel.
• ONE control is made into the BASE control.
• The OTHER control is made an AUXILIARY control.
(All remote controls leave the factory as a BASE).
Initial remote control settings
1. Set both the controls to operate the fan.
2. Select one of the remote controls to be the BASE unit.
BASE
DISPLAY
BASE Check
To confirm that the control is the BASE:
1. Press
for 3 seconds until a beep is
heard.
2. Confirm temperature display shows 'b'.
3. Press
again to set.
COMFORT•TOUCH ♦ DUAL REMOTE CONTROL - AUXILIARY
Change the other remote to be used in the room to AUXILIARY
1. Press
until a beep is heard. Remote displays 'b'.
2. Press fan up
or down
buttons to change the display to 'A'.
3. Press
again to set.
The fan will now respond to either of the remotes when pressed.
• Reminder! These steps will have to be repeated whenever the
batteries are changed.
• When AUTO-SPEED, SECURITY, SAVER or TEST modes are in effect at any control: Automatic control will only be from the
control that was last operated manually.
AUXILIARY
DISPLAY
TWO CONTROLS OPERATING ONE FAN
When two controls are used for the same fan, we suggest that both controls be set for the same features
(AUTO-SPEED, SAVER, etc.) so that performance remains the same as you move from one to the other. Remember, the fan will only respond to updates from the control that was last operated manually.
22
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the finish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning agents. These will
damage the finish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
PROBLEM
FAN
WILL NOT START
PROBLEM
FAN WOBBLES OR SHAKES
EXCESSIVELY
FAN NOISY DURING
OPERATION
BREAK-IN PERIOD
DOES NOT RUN ON
LOW SPEED
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type
as removed from the fixture. Each fan is rated for a maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
POSSIBLE REMEDIES..
Check main circuit fuses, circuit breakers, or wall switch position.
POSSIBLE REMEDIES
Check all wire connections, making sure the power is turned off during this inspection.
3-SPEED
Check that reverse switch is not set in center of throw.
Be sure canopy pin is properly set into the slot on the ball.
Check the screws holding the blade holders to the flywheel (or direct drive motor). Tighten as necessary.
Check that bladeholders have not been bent during installation.
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary.
Tighten the blade to bladeholder screws.
Tighten canopy screws and mounting plate assembly.
Check and tighten blade holders to flywheel (or direct drive motor).
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have
fallen off the wire splices. Tighten or adjust as necessary.
Let fan run at high speed for two (2) hours
If new, “break-in” may be required - run at higher speed for several days
FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective
capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit.
FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speed pull-chain switch assembly; or
defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly.
PROBLEM
NO FAN OR LIGHT
FAN WOBBLES OR SHAKES
EXCESSIVELY
FAN NOISY DURING
OPERATION
BREAK-IN PERIOD
DOES NOT RUN ON
LOW SPEED
INTELI•TOUCH
POSSIBLE REMEDIES..
Check main circuit fuses, curcuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
Be sure canopy pin is properly set into the slot on the ball
Check the screws holding the blade holders to the fan motor. Tighten as necessary.
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or
have fallen off the wire splices. Tighten or adjust as necessary.
Let fan run at high speed for two (2) hours
If new, “break-in” may be required - run at higher speed for several days
LIGHTS FLASH OR BLINK DURING OPERATION OF W-32 WALL CONTROLS/FAN MAY ROTATE OR MAKE AUDIBLE TONES DURING
OPERATION OF THE W-11 AND W-12 WALL CONTROLS: Normal operation.
WHEN AC POWER IS TURNED ON FOR THE FIRST TIME, THE LIGHTS OPERATE NORMALLY, BUT W-32 WALL CONTROL OPERATION IS
REVERSED: FAN BUTTON OPERATES THE LIGHTS; LIGHT BUTTON OPERATES THE FAN: Reverse the 2 black and white striped wire
connections.
FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTERMITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly.
23
PROBLEM
PROBLEM
FAN WILL NOT START
FAN WOBBLES OR SHAKES
EXCESSIVELY
FAN NOISY DURING
OPERATION
VERSA•TOUCH
POSSIBLE
POSSIBLE REMEDIES
REMEDIES..
Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
Pin connectors are not making good contact. Release lockpin and check pins at end of downrod & inside
coupler and also 9 pin connector under cover.
Battery weak - install fresh battery.
Fan receiver defective - replace.
Check the receiver and transmitter dip switch to see if they are on the same frequency setting.
Be sure canopy pin is properly set into the slot on the ball.
Check that bladeholders have not been bent during installation and blades are balanced.
Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly
attached to the ceiling outlet box. Make sure that the downrod assembly is secured firmly
Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy and
switch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.
Tighten blade holders to flywheel (or direct drive motor)/and blade to bladeholder screws.
Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.
If new, “break-in” may be required - run at higher speed for several days.
DOES NOT RUN ON
LOW SPEED
BATTERY LIFE
Not using Alkaline batteries: Replace with Alkaline batteries.
SEEMS SHORT
LIGHT O.K., NO FAN: Pin connectors are not making good contact, check 9 pin connector under top cover. FAN O.K., NO LIGHT; Defective
receiver; Replace receiver. Defective motor; Replace motor. Broken socket; Replace socket. Defective receiver; Replace Receiver. FAN AND
LIGHT ON FULL, NO CONTROL; Defective receiver; Replace Receiver. MISSING ONE SPEED: Defective receiver; ReplaceReceiver. FAN DOESN’T
CHANGE SPEED, LIGHT O.K.: Replace receiver. FAN O.K., LIGHT NOT DIM: Defective receiver; Replace Receiver. NO REVERSE: Defective
receiver; Replace Receiver. FAN OPERATES ONLY WHEN TRANSMITTER IS CLOSED: Check antenna wire is not touching metal plate. FAN
STARTS WORKING BY ITSELF: Frequency interference; Change dip switch code.
PROBLEM
COMFORT•TOUCH
FAN O.K., NO LIGHT
REMOTE CONTROL OF FAN IS ERRATIC
SELECTING WINTER MODE CANCELS AUTO-SPEED
CHANGING SPEED OR DIRECTION CANCELS WINTER
FAN APPEARS TO RESPOND TO UNKNOWN SIGNAL
CONTROL ALSO OPERATES A SECOND FAN IN HOME
TEMPERATURE DISPLAY DOES NOT CHANGE QUICKLY
FAN WOBBLES OR SHAKES EXCESSIVELY
POSSIBLE REMEDIES..
Check for burned-out light bulb. Check fan light wires.
Check batteries installed correctly. Install fresh ALKALINE batteries.
Normal.
Normal.
Change channel of control and fan to a number between 49 and 63.
Change channel on control and fan.
Normal. Updates only every 2 minutes.
Make sure hanging ball slot is properly aligned.
Tighten canopy and mounting crossbar screws.
Tighten all blade screws. Blades must be balanced (contact your dealer).
FAN NOISY DURING OPERATION
Tighten glassware and light bulbs.
Tighten motor housing screws.
Tighten canopy and mounting crossbar screws.
DOES NOT RUN ON LOW SPEED
If new, “break-in” may be required - run at higher speed for several days.
BATTERY LIFE SEEMS SHORT
Not using Alkaline batteries: Replace with Alkaline batteries.
TEMPERATURE READINGS
Temperature accuracy = –3 F
FAN DOES NOT RESPOND TO REMOTE CONTROL: Power to fan is off; wrong remote being used; remote channel changed; fan receive SET
channel changed; or fan antenna not receiving. See above; in locations with two or more fans in different rooms check that controllers are
in right rooms; change SET channel to match fan; change fan SET channel to match remote; check antenna connected to RCM; check antenna
positioned correctly; if batteries weak by moving remote close to fan; check that remote not laying on metal surface causing weak signal; or
connect Earth ground to fan.
FAN APPEARS TO RESPOND TO UNKNOWN SIGNAL OR IS ERRATIC: Invalid lower channel SET; 2nd remote in area SET to same channel; or
remote buttons pressed too quickly Be sure SET channel is between 49 and 63; check SET channels of any other remotes at site (check if
nearby homes have Comfort Touch fans installed- remote signal can travel 50 ft.); and for proper operation of the control you must wait “one
second” between presses.
AFTER POWER FAILURE, FAN AND LIGHTS ARE OFF: Normal: To immediately restore fan to its original settings press any button. Fan will
reset itself within about 30 minutes after power is restored when remote sends normal update message to fan.
WHEN AC POWER IS TURNED ON, LIGHT COMES ON OR FAN TURNS: Remote control defective; remote buttons pressed too soon; AC
electricity irregularities (noise spikes, fluctuations, or failure). Turn off with remote and restart; replace remote control unit; or wait twenty
seconds for electronics warm-up; check AC electricity for irregularities (defective light dimmers, noise spikes, voltage changes caused by
appliances, motors, supply brown outs or interruptions, or storms, etc).
24
PRINTED IN ROC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement