Alinco | DJ-S17 E | Instruction manual | Alinco DJ-S17 E Instruction manual

Alinco DJ-S17 E Instruction manual
VHF/UHF FM TRANSCEIVER
DJ-S17 E/TFH
DJ-S47 E
Instruction Manual
VOL
VOL
NAME
SQL
KL
RPT
PO
/C
V/MNA
ME
SQL
KL
V/M/C
RPT
PO
MW
MW
DJ-S17
UHF FM TRANSCEIVER
DJ-S47
UHF FM TRANSCEIVER
Thank you for purchasing your new Alinco transceiver.
This instruction manual contains important safety and
operating instructions. Please read this manual
carefully before using the product and keep it for future
reference.
ALINCO, INC.
2
NOTICE / Compliance Information Statement
NOTICE / Compliance Information Statement
Conformity Information
Alinco, Inc. Electronics Division hereby declare on our sole responsibility that the
product(s) listed below comply the essential requirements of the Directive 1999/5/EC,
The council of 3/9/99 on Radio Equipment and Telecommunication Terminal
Equipment and the mutual recognition of their conformity and with the provisions of
Annex, after having performed the required measurements at Notified Bodies per
Standards, and relative certificate(s) or document(s) can be reviewed at http://www.
alinco. com/Ce/
DJ-S17E: VHF FM Transceiver 144.000~145.995MHz
DJ-S47E: UHF FM Transceiver 430.000~439.995MHz
This device is authorized for use in all EU and EFTA member states. An operator's
license is required for this device.
Copyright © All rights reserved. No part of this document may be reproduced, copied,
translated or transcribed in any form or by any means without the prior written
permission of Alinco. Inc., Osaka, Japan, English Edition Printed in Japan.
3
Warning
Warning
To prevent any hazard during operation of Alinco's radio product, in this manual and
on the product you may find symbols shown below. Please read and understand the
meanings of these symbols before starting to use the product.
d Danger
d Alert
d Caution
d
a
m
This symbol is intended to alert the user to an immediate danger that
may cause loss of life and property if the user disregards the warning.
This symbol is intended to alert the user to a possible hazard that
may cause loss of life and property if the user disregards the warning.
This symbol is intended to alert the user to a possible hazard that may
cause loss of property or injure the user if the warning is disregarded.
Alert symbol. An explanation is given.
Warning symbol. An explanation is given.
Instruction symbol. An explanation is given.
d Alert
■ Environment and condition of use
It is recommended that you check local traffic regulations regarding the use of
radio equipment while driving. Some countries prohibit or apply restrictions
for the operation of radios and mobile- phones while driving.
a
j especially medical ones. It may cause interference to those devices.
a Keep the radio out of the reach of children.
In case a liquid leaks from the product, do not touch it. It may damage your
j skin. Rinse with plenty of cold water if the liquid contacted your skin.
Never operate this product in facilities where radio products are prohibited for
j use such as aboard aircraft, in airports, in ports, within or near the operating
Do not use this product in close proximity to other electronic devices,
area of business wireless stations or their relay stations.
j informed in advance when you travel.
The manufacturer declines any responsibilities against loss of life and/or
a property due to a failure of this product when used to perform important tasks
Use of this product may be prohibited or illegal outside of your country. Be
like life-guarding, surveillance, and rescue.
4
Warning
j and/or damage to the product(s).
Risk of explosion if battery is replaced with an incorrect type.
a Dispose of, or recycle used batteries according to your local regulations.
The manufacturer declines any responsibilities against loss of life and property due to
a a failure of this product when used with or as a part of a device made by third parties.
Use of third party accessory may result in damage to this product. It will void
a our warranty for repair.
Do not use multiple radios in very close proximity. It may cause interference
■ Handling this product
Be sure to reduce the audio output level to minimum before using an earphone
or a headset. Excessive audio may damage hearing.
a
Do not open the unit without permission or instruction from the manufacturer.
m Unauthorized modification or repair may result in electric shock, fire and/or
malfunction.
l in electric shock, fire and/or malfunction.
Do not place the product in a container carrying conductive materials, such as
j water or metal in close proximity to the product. A short-circuit to the product
Do not operate this product in a wet place such as shower room. It may result
may result in electric shock, fire and/or malfunction.
■ About chargers
Do not use adapters other than having the specified voltage. It may result in
electric shock, fire and/or malfunction.
j
Do not plug multiple devices using an adapter into a single wall outlet. It may
j result in overheating and/or fire.
j Do not handle adapter with a wet hand. It may result in electric shock.
Securely plug the adapter into the wall outlet. Insecure installation may result
a in short-circuit, electronic shock and/or fire.
Do not use the adapter if the plug or socket contacts are dirty. Overheating and/or
j short-circuiting may result in fire, electric shock and/or damage to the product.
■ About power supply
j Use only appropriate, reliable power supply of correct voltage and capacity.
Do not connect cables in reverse polarity. It may result in electric shock, fire
j and/or malfunction.
Do not plug multiple devices including the power supply into a single wall
j outlet. It may result in overheating and/or fire.
5
Warning
j Do not handle a power supply with a wet hand. It may result in electric shock.
Securely plug the power supply to the wall outlet. Insecure installation may
a result in short-circuiting, electronic shock and/or fire.
Do not plug the power supply into the wall socket if the contacts are dirty.
j Short-circuit and/or overheating may result in fire, electric shock and/or
damage to the product.
j fire, electric shock and/or damage to the product.
Do not modify or remove fuse-assembly from the DC cable. It may result in
■ Cigar-lighter cable
Do not use the cable at any other than the specified voltage. It may result in
electric shock, fire and/or malfunction.
j
j Do not handle cigar cable with a wet hand. It may result in electric shock.
■ In case of emergency
In case of the following situation(s), please turn off the product, switch off the source
of power, then remove or unplug the power-cord. Please contact your local dealer of
this product for service and assistance. Do not use the product until the trouble is
resolved. Do not try to troubleshoot the problem by yourself.
• When a strange sound, smoke and/or strange odor comes out of the product.
• When the product is dropped or the case is broken or cracked.
• When a liquid penetrated inside.
• When a power cord (including DC cables, AC cables and adapters) is damaged.
a accessories from the wall outlet if a thunderstorm is likely.
For your safety, turn off then remove all related AC lines to the product and its
■ Maintenance
Do not open the unit and its accessories. Please consult with your local dealer
of this product for service and assistance.
m
6
Warning
d Caution
■ Environment and condition of use
Do not use the product in proximity to a TV or a radio. It may cause
interference or receive interference.
j
Do not install in a humid, dusty or insufficiently ventilated place. It may result
j in electric shock, fire and/or malfunction.
Do not install in an unstable or vibrating position. It may result in electric
j shock, fire and/or malfunction when/if the product falls to the ground.
Do not install the product in proximity to a source of heat and humidity such as
j a heater or a stove. Avoid placing the unit in direct sunlight.
Be cautious of a dew formation. Please completely dry the product before use
j when it happens.
■ About transceiver
Be cautious of the whip antenna when carried in your shirt-pocket etc. It may
make contact with your eye and cause injury.
a
Do not connect devices other than specified ones to the jacks and ports on the
j product. It may result in damage to the devices.
Turn off and remove the power source (AC cable, DC cable, battery, cigar
a cable, charger adapter etc.) from the product when the product is not in use for
extended period of time or in case of maintenance.
j Never pull the cord alone when you unplug AC cable form the wall outlet.
Use a clean, dry cloth to wipe off dirt and condensation from the surface of the
a product. Never use thinner or benzene for cleaning.
■ About power supply
Use only reliable power supply of specific DC output range and be mindful of
the polarity of the cable and DC-jack.
a
a Always turn off the power supply when connecting or disconnecting the cables.
When using an external antenna, make sure that the antenna ground is not
a common with the ground of the power supply.
When a unit is powered from an external DC power source (adapter, power
a supply, cigar-plug etc), please make sure that such external DC power source
shall be a limited power source per IEC/EN 60950-1.
7
Warning
■ Lightning
Any person is not safe outdoor during thunderstorm and lightning. This condition is
getting worse if somebody keeps a hand-held radio; chances of being hit by lightning are
doubled since lightning may hit a radio antenna as well. At this time, there is no handheld radio having any kind of protection against lightning current (which is higher than
10 kA.). Note also that no car provides adequate protection of its passengers or drivers
against lightning as well. Therefore, Alinco will not take responsibility for any danger
associated with using its hand-held radios outdoor or inside the car during lightning.
■ Limited Power Source
Adhering to the requirement of the following warning ensures compliance of the
transceiver with the safety standard for information technology equipment, EN 609501. Please note that the transceiver enclosure only provides mechanical protection of
its internal parts; it will not contain a fire within the device if the fire starts under
certain fault conditions. Alinco will not take responsibility for any fire hazard
associated with powering the transceiver or charging its batteries using a power source
which does not belong to the limited power sources in the meaning of EN 60950-1.
Excluded from possible use with the transceiver are most car cigarette lighters and
some DC (AC/DC) power supplies. Make sure that the power supply used with the
transceiver is a limited power source.
■ Water-proof
The IEC 60529/IPX7 is an European system of test specification standards for
classifying the degrees of protection provided by the enclosures of electrical
equipment. An IPX7 designation means that the unit withstands immersion in one
meter (approx 3ft) of still water for up to 30 minutes.
The factory guarantees this grade for 1 year provided all the jack covers are properly
and securely closed. However, please understand that this unit is NOT an IPX7
COMPLIANT, but compatible; we have tested and approved at our engineering stage
that this product meets the requirement of IPX7 but we do not test it unit-by-unit at the
factory before delivery. Please understand that water-pressure such as washing the
unit with running water may cause damage to the unit and voids warranty. Never
immerse the unit uselessly under the water (V/UHF signal does not propagate in water
at all). If the unit is dropped in water, please pick it up immediately and wipe with a
clean dry cloth. Use only specified water-proof accessories when the unit is intended
for use in rainy/wet conditions.
8
Introduction
Introduction
Thank you very much for purchasing this excellent Alinco transceiver. Our products
are ranked among the finest in the world. This radio has been manufactured with state
of the art technology and it has been tested carefully at our factory. It is designed to
operate to your satisfaction for many years under normal use.
PLEASE READ THIS MANUAL COMPLETELY TO LEARN ALL THE
FUNCTIONS THE PRODUCT OFFERS. WE MADE EVERY ATTEMPT TO
WRITE THIS MANUAL TO BE AS COMPREHENSIVE AND EASY TO
UNDERSTAND AS POSSIBLE. IT IS IMPORTANT TO NOTE THAT SOME OF
THE OPERATIONS MAY BE EXPLAINED IN RELATION TO INFORMATION
IN PREVIOUS CHAPTERS. BY READING JUST ONE PART OF THE MANUAL,
YOU RISK NOT UNDERSTANDING THE COMPLETE EXPLANATION OF THE
FUNCTION.
9
Contents
Contents
NOTICE / Compliance Information Statement ................................................3
Warning...............................................................................................................4
Introduction ........................................................................................................9
Contents ...........................................................................................................10
1.Features .........................................................................................................13
1.1 Accessories .........................................................................................................13
2.Accessories ...................................................................................................14
2.1 Installations .........................................................................................................14
2.1.1 Antenna ......................................................................................................14
2.1.2 Hand Strap..................................................................................................14
2.1.3 Belt Clip .....................................................................................................14
2.1.4 Battery Pack ...............................................................................................15
2.1.5 Prevent Short Circuiting the Battery Pack .................................................17
2.1.6 Dry Cell Case (optional).............................................................................18
2.1.7 Battery-Level Icon......................................................................................19
3.Names and Operations of Parts ..................................................................20
3.1 Names and Operations of Keys and Ports...........................................................20
3.2 Keypad ................................................................................................................22
3.3 Display (LCD) ....................................................................................................23
4.Basic Operation ............................................................................................24
4.1 Turning On the Power.........................................................................................24
4.2 Adjusting the Audio Output (Volume) ...............................................................24
4.3 Adjusting the Squelch .........................................................................................25
4.4 Setting the Frequency in the VFO Mode ............................................................25
4.4.1 Setting the Frequency.................................................................................25
4.4.2 Setting the Tuning Step ..............................................................................25
4.4.3 Shift Direction and Offset Frequency Settings...........................................26
4.5 Memory Mode ....................................................................................................27
4.5.1 How to Program Memory Channel(s) ........................................................27
4.5.2 Recalling a Memory Channel.....................................................................28
4.5.3 Deleting a Memory Channel ......................................................................28
4.5.4 How to Program Call Channel ...................................................................28
4.5.5 Programming a Repeater-Access Function Setting....................................28
4.5.6 Programmable Parameters in Memory Channels.......................................29
4.6 Call-Channel Mode.............................................................................................30
10
Contents
4.7 Receiving ............................................................................................................30
4.7.1 Monitor Function........................................................................................30
4.8 Transmitting .......................................................................................................31
4.8.1 Selecting the Output Level .........................................................................31
5.Useful Functions ...........................................................................................32
5.1 Scan Modes.........................................................................................................32
5.1.1 VFO-Scan...................................................................................................32
5.1.2 Memory-Scan .............................................................................................32
5.1.3 Setting Skip Channels ................................................................................33
5.2 Keylock ...............................................................................................................33
5.3 Tone-Burst ..........................................................................................................33
5.4 Naming Memory Channels .................................................................................34
5.4.1 Setting Name-Tag.......................................................................................34
5.4.2 Using the Channel Name Function ............................................................34
5.5 Auto-Power-Off (APO) ......................................................................................35
5.5.1 Setting APO................................................................................................35
5.5.2 APO Operation ...........................................................................................35
5.6 Time-Out-Timer (TOT) ......................................................................................35
5.6.1 Setting TOT................................................................................................35
5.6.2 TOT Operation ...........................................................................................35
5.7 Lamp ..................................................................................................................36
6.Selective Calling............................................................................................37
■ Selective Calling Operations ...................................................................................37
6.1 Tone Squelch (TSQ) ...........................................................................................37
6.1.1 Setting the Tone Squelch............................................................................37
6.1.2 Setting the Tone Frequency........................................................................37
6.1.3 Switching Off the Tone Squelch ................................................................38
6.1.4 To Differentiate the ENC/DEC Tones .......................................................38
6.1.5 Tone Squelch Operation.............................................................................38
6.2 DCS ....................................................................................................................38
6.2.1 Setting the DCS ..........................................................................................38
6.2.2 Changing the DCS Code ............................................................................39
6.2.3 Switching Off DCS ....................................................................................39
6.2.4 DCS Operation ...........................................................................................39
7.Special Functions..........................................................................................40
7.1 ATT (Attenuator) ................................................................................................40
7.2 Battery Refresh ...................................................................................................40
7.3 Repeater-Access..................................................................................................41
11
Contents
8.Set Mode........................................................................................................42
8.1 Set Mode Operation ............................................................................................42
8.2 Entering the Set Mode ........................................................................................43
8.3 Available Parameters ..........................................................................................43
8.3.1 Menu 1 Battery Save (BS) Function ..........................................................43
8.3.2 Menu 2 Timer/Busy Scan Setting ..............................................................43
8.3.3 Menu 3 Beep Function ...............................................................................44
8.3.4 Menu 4 Tone-Burst Frequency Setting ......................................................44
8.3.5 Menu 5 Clock Shift Setting ........................................................................44
8.3.6 Menu 6 Busy Channel Lockout Setting .....................................................45
8.3.7 Menu 7 TOT (Time-Out-Timer) Setting ....................................................45
8.3.8 Menu 8 TOT Penalty Time ........................................................................45
8.3.9 Menu 9 Tuning Step Setting.......................................................................45
8.3.10 Menu 10 Shift Direction Setting ................................................................45
8.3.11 Menu 11 Offset Frequency Setting ............................................................45
8.3.12 Menu 12 Tone Squelch Setting ..................................................................46
8.3.13 Menu 13 Tone Frequency Setting ..............................................................46
8.3.14 Menu 14 DCS Setting.................................................................................46
8.3.15 Menu 15 APO (Auto-Power-Off) Setting ..................................................46
8.3.16 Menu 16 Skip Channel Setting...................................................................46
8.3.17 Menu 17 ATT (Attenuator) Setting............................................................46
8.3.18 Menu 18 Battery Charge Function .............................................................46
8.3.19 Menu 19 Battery Type Setting ...................................................................47
9.Cloning and Packet Operation ....................................................................48
9.1 Cloning................................................................................................................48
9.1.1 Cable Connection .......................................................................................48
9.1.2 Master/Slave Units .....................................................................................48
9.1.3 Master Unit Operation................................................................................49
9.1.4 Slave Unit Operation ..................................................................................49
9.2 Packet Operation.................................................................................................50
9.2.1 Packet Operation Connections ...................................................................50
10.Maintenance and Reference......................................................................51
10.1 Troubleshooting ..................................................................................................51
10.2 Resetting .............................................................................................................52
10.3 Options................................................................................................................53
10.3.1 Microphone/Speaker Cable (EDS-10)........................................................54
10.3.2 Battery Packs..............................................................................................54
10.3.3 Using the Chargers .....................................................................................55
11.Specifications .............................................................................................61
12
1.Features
1. Features
This transceiver has the following main features.
■ High-grade waterproof compatible to IPX7* (submersible 1m/3feet for
1
30min.) and rugged body
■ 39 CTCSS tone squelch
■ 104 DCS digital code squelch
■ Time-Out-Timer
■ Alphanumeric display
■ 4 tone-burst tones (1750, 2100, 1000, 1450Hz)
■ A quick "Repeater-Access" function
■ Refresh function for rechargeable battery reconditioning
■ Cable Cloning
* Please read page 8 for more details.
1.1 Accessories
• Ni-MH battery pack EBP-65 (7.2V 700mAh)
• EDC-147 (AC 230V) wall charger (E/TFH version)/EDC-148 (U.K. models)
• Flexible whip antenna EA0141 (DJ-S17E version)
• Flexible whip antenna EA0142 (DJ-S17TFH version)
• Flexible whip antenna EA0143 (DJ-S47E version)
• Belt clip
• Hand strap
• Instruction manual
* Accessories may differ depending on the version you have purchased.
Please contact your local dealer for details of standard accessories and the warrantypolicy before purchase.
13
2.Accessories
2. Accessories
2.1 Installations
2
2.1.1 Antenna
■ Attaching the Antenna
1. Hold the antenna by its base.
2. Align the grooves at the base of the antenna with
the protrusions on the antenna connector.
3. Slide the antenna down and turn it clockwise until
it stops.
4. Confirm that the antenna is securely connected.
NOTE:
This antenna has been designed very flexible. It
is softer than conventional ones but not a defect.
■ Removing the Antenna
Turn the antenna counter-clockwise to disconnect the antenna.
2.1.2 Hand Strap
Attach the hand strap as shown. There are two ways
to attach it.
2.1.3 Belt Clip
■ Attaching the Belt Clip
1. Put the belt clip on the back of the unit, and turn
the screw clockwise until it stops.
2. Confirm that the belt clip is securely attached.
■ Removing the Belt Clip
Turn the screw counter-clockwise to remove the belt clip.
14
2.Accessories
2.1.4 Battery Pack
For the specifications and the charging procedures, please refer to "Battery
Packs"(page 54) and "Using the Chargers"(page 55).
■ Attaching the Battery Pack
Align the catches on the battery pack with the
grooves on the unit, and close the latch until it clicks.
2
■ Removing the Battery Pack
Push the latch in the direction of the arrow, and pull
out the battery pack.
Caution
• The battery pack isn't fully charged when shipped. It must be charged
before use.
• Charging should be conducted in a temperature range of 0ºC to +40ºC
(+32ºF to +104ºF).
• Don't modify, dismantle, incinerate or immerse the battery pack in the water
as this can be dangerous.
• Never short-circuit the battery pack terminals, as this can cause damage to
the equipment or lead to heating of the battery which may cause burns.
• Unnecessary prolonged charging (overcharging) can deteriorate battery
performance.
• The battery pack should be stored in a dry place where temperature is in
-10ºC to +45ºC (-14ºF to +113ºF) range. Temperatures outside this range
can cause the battery liquid to leak. Exposure to prolonged high humidity
can cause corrosion of metal components.
• Battery-packs are a consuming part. When its operating time becomes
considerably short after a normal charge, please consider that the pack is
exhausted and replace it with a new one.
• The battery pack is recyclable. Check with your local waste officials for
details on recycling options or proper disposal in your area.
15
2.Accessories
Caution
2
• Li-ion battery packs can't be charged using DC-jack on the unit (Only NiMH battery packs can be charged).
• Risk of explosion, generation of heat or leak of chemicals inside if the
battery is replaced by an incorrect type. Use always the recommended
types of batteries in this manual only.
■ Charging the Battery Pack Using DC-Jack on the Unit
The unit can charge the EBP-65 and EBP-66 optional Ni-MH battery packs by
supplying DC power through the DC-jack on the unit using EDC-147/148 wall
chargers or an optional DC power supply (DC 12V~DC 16V, 1A or more: IEC/EN
60950-1 compliant) and a DC cable such as EDC-37.
1. Attach the battery pack by referring to "Battery Pack" (page 15).
2. Connect the AC adapter plug to the DC-jack on the
unit then connect the charger's adapter to the wall
outlet.
* AC adapter may look different.
3. Turn on the unit and set the battery charge
parameters. Please refer to "Set Mode" (page 42)
then:
* "Battery Charge Function" (page 46)
Select CHG-ON.
* "Battery Type Setting" (page 47)
Select BAT-NI.
4. After completing the settings, a flashing
appears on the display. Make sure the icon is
flashing then turn off the unit. It takes about 10
hours/30hours for EBP-65/66 respectively to
complete the charge.
IMPORTANT NOTE:
While this function is activated, without attaching a battery pack or the remaining
battery level is below the usable range, the unit turns on by just connecting the
DC source such as an adapter or a DC cable (without operating the power key).
16
2.Accessories
NOTE:
• Please read the general safety instructions included in the optional accessories
to correctly and safely use them.
• EDC-147/148 can't be used as the adapter for operation. These adapters are for
charging purposes only.
• Chargers can't perform the correct charge when the AC voltage is unstable.
•
flashes even EBP-65/66 aren't attached. To avoid short-circuit, never
activate this function when the pack isn't attached to the unit.
• Li-ion battery packs can't be charged in this way.
2
2.1.5 Prevent Short Circuiting the Battery Pack
Be extra cautious when carrying the rechargeable battery pack; short circuiting will
produce surge current possibly resulting in fire.
17
2.Accessories
2.1.6 Dry Cell Case (optional)
An EDH-34 is available for operation with using AA cells.
Lift up the catches ① on the top of the case to
remove the cover.
2
Place 6 AA cells, then close the cover in order of ②
then ③ . Be sure that the cover is securely closed.
Use high-performance AA cells such as Alkaline or
Oxyride cells.
Caution About Handling Dry Cell Case:
• This dry cell case isn't water-proof.
• Be extra-cautious to the polarity of the cells (+)/(-). Misplacing cells may
result in leak, fire or explosion.
• Use new batteries of the same type and brand when placing them.
• Use of rechargeable cells is prohibited and the manufacturer declines any
responsibilities for damages/injuries that may cause to the users and their properties.
• It is recommended to clean the battery contacting terminals with a clean
dry cloth from time to time.
• Risk of explosion if batteries are replaced by an incorrect type.
• Batteries are recyclable. Please check the local rules for proper
recycle/disposal in your area.
Caution About Battery Charge Function:
The battery charge function is on by default. With this function on and the dry
cells installed, connecting the provided EDC-147/148 AC adapter or an optional
external power supply(stabilized power supply, cigarette lighter cable, etc.) to
the DC-jack on the unit may send current through the dry cells, resulting in
battery leak, heat or explosion. Referring to "Menu 18 Battery Charge Function"
on page 46, be sure to set this function off (select CHG-OF) when the unit is
equipped with the dry cells. However, there is no danger even if CHG-ON is
selected as long as no external power supply is connected to the unit.
18
2.Accessories
2.1.7 Battery-Level Icon
During the operation, a black battery icon indicates
that the battery-level is in usable range. When it
turns to empty, please charge the pack or replace the
cells with new ones.
2
19
3.Names and Operations of Parts
3. Names and Operations of Parts
3.1 Names and Operations of Keys and Ports
■ Top and Front
3
③
④
⑥
⑤
⑦
②
Dial
Microphone/
Speaker jack
TX/RX lamp
Speaker
Power key
Microphone
Display (LCD)
Keypad
20
①
VOL
SQL
KL
V/M/C
NAME
RPT
PO
MW
⑧
Rotate the dial to select the frequency of operation, memory
channel, offset frequency, tone frequency, DCS code, Set mode
settings, and the characters for name-tags. Rotating the dial
while pressing the FUNC key increases or decreases the
frequency in 1MHz order.
For an optional speaker/Mic connection. Securely close the
cover for water-proof while the accessory isn't in use.
Lights green when the squelch is unmuted. Lights red during
transmission.
A speaker is built in.
Press the power key down for approximately one second to turn
on/off the unit.
Speak into the microphone from a distance of about 5cm (2").
Refer to "Display (LCD)" (page 23).
Refer to "Keypad" (page 22).
3.Names and Operations of Parts
■ Side
3
21
3.Names and Operations of Parts
3.2 Keypad
VOL
SQL
KL
V/M/C
NAME
RPT
PO
MW
3
key
Without pressing the FUNC key.
Audio level adjustment (page 24).
SQL adjustment (page 25).
Start scanning (page 32).
Key lock setting (page 33).
While
appears after the FUNC key is pressed.
Naming memory channels setting
(page 34).
Repeater-Access function setting
(page 41).
Hi / Low power setting (page 31).
Switches between the VFO / Memory / Memory programming (page 27).
Call channel mode (page 25).
22
3.Names and Operations of Parts
3.3 Display (LCD)
3
23
4.Basic Operation
4. Basic Operation
4.1 Turning On the Power
Hold the
key down for a second. To turn off the power, hold the
until the display turns off.
key down
default frequencies
<DJ-S17>
E
TFH
4
<DJ-S47>
E
NOTE:
This manual has been edited based on DJ-S17E.
Frequency display may vary depending on the model you have purchased.
4.2 Adjusting the Audio Output (Volume)
• There are 21 audio output levels (00~20).
• The default setting is level 00. There is no audio output at this status.
1. Press the
key. The level is displayed on the
LCD.
2. Rotate the dial to increase or decrease the level.
As the setting value increases, the audio becomes
louder.
3. Press any key except for the MONI key or just leave it for 5 seconds to
automatically complete the setting.
24
4.Basic Operation
4.3 Adjusting the Squelch
Squelch is a function that eliminates the noise when no signals are being received.
• There are 11 squelch levels (00~10).
• The default setting is Level 00.
1. Press the
key. The squelch level is displayed
on the LCD.
2. Rotate the dial to increase or decrease the squelch
level. Set to the lowest level that the noise is cut.
3. Press any key except for the MONI key or just leave it for 5 seconds to
automatically complete the setting.
4
4.4 Setting the Frequency in the VFO Mode
The factory default of this unit is the VFO mode. The VFO mode allows you to
change the frequency and operating parameters by using the dial and key operations.
4.4.1 Setting the Frequency
■ To Select the VFO Mode
The
key switches between the VFO, Memory and Call channel mode each time
the key is pressed.
"
" is displayed in the Memory mode and " " in the Call channel mode.
■ Selecting the Operating Frequency
Rotate the dial clockwise to increase the frequency by one tuning step.
Rotate the dial counter-clockwise to decrease it by one tuning step.
A beep sounds after every 0.5MHz increases/decreases in the frequency.
■ To Quickly Change the Frequency
Press the FUNC key, and while
is displayed on the screen, rotate the dial to increase
or decrease (depending on the direction of rotation) the frequency by 1MHz order.
4.4.2 Setting the Tuning Step
1. Select the menu 09 in the Set mode to display the current tuning step.
2. Rotate the dial to select the desired tuning step.
25
4.Basic Operation
3. Press any key except for the MONI or FUNC key to complete setting.
NOTE:
• Refer to "Set Mode Operation" on page 42 for the list of parameters that can
be programmed in the Set mode and "Entering the Set Mode" on page 43 to
enter the Set mode.
• Tuning step can't be changed in the Memory mode.
• When the tuning step is changed from 5kHz,10kHz,15kHz,20kHz or 30kHz to
12.5kHz and 25kHz or vice versa, the operating frequency and the shift width
automatically suit to the new setting.
4
4.4.3 Shift Direction and Offset Frequency Settings
In conventional repeater systems, a signal received on one frequency is retransmitted
on another frequency. The difference between these two frequencies is called the
offset frequency. The selectable offset frequency of this unit is from 0 to 99.995MHz.
The TX frequency can be shifted in the plus or minus direction based on the RX
frequency when the PTT key is pressed. This direction is called the shift direction.
You can set the shift direction and offset frequency in the Set mode. Refer to "Set
Mode Operation" on page 42 and "Entering the Set Mode" on page 43. To operate the
Repeater-Access function, use the Repeater-Access function memory. Refer to
"Programming a Repeater-Access Function Setting" on page 28.
■ Setting the Shift Direction
1. Select the menu 10 in the Set mode to display the current shift direction setting.
2. Rotate the dial to select the desired shift direction.
A (-) means that the TX frequency is lower than the RX frequency.
A (+) means vice versa.
SFD-OF
SFD- –
SFD- +
3. Press any key except for the MONI or FUNC key to complete setting.
Caution
Select "SFD-OF" to cancel the shift setting.
26
4.Basic Operation
■ Setting the Offset Frequency
1. Select the menu 11 in the Set mode to display the current offset frequency.
2. Rotate the dial to increase or decrease the frequency.
Clockwise: each click increases the frequency by one tuning step.
Counter-clockwise: each click decreases the frequency by one tuning step.
Rotate the dial while holding down the
key to increase or decrease the
frequency in 1MHz steps.
3. Press any key except for the MONI or FUNC key to complete setting.
NOTE:
• Please refer to "Selective Calling" (page 37) to set the CTCSS/DCS tones
usually required for conventional Repeater-Accesses.
• If the offset frequency is set to exceed the transmitting frequency range of this
unit, "OFF" appears on the display and a beep sounds when the PTT key is
pressed. You can not transmit in this state.
4
4.5 Memory Mode
This mode allows recalling and operating the preprogrammed frequency or setting in
the memory channels. This unit provides up to 200 memory channels, 1 CALL
channel and 1 Repeater-Access function memory.
4.5.1 How to Program Memory Channel(s)
1. Select a frequency and operating parameters to be programmed in the VFO mode.
Refer to "Programmable Parameters in Memory Channels" on page 29 for the list of
parameters that can be programmed in the Memory mode.
2. Select the Memory mode by pressing the
key. In the Memory mode,
memory channels, or
appear on the display.
3. Press the FUNC key to display
,
.
4. Rotate the main dial to select the desired memory channel number (0 to 199) while
is displayed. An empty channel is shown with a flashing "
".
5. By pressing the
key again while
is on the display, a beep sounds and
programming is completed. If
disappeared before pressing the
key, press the
FUNC key again and then
key.
27
4.Basic Operation
4.5.2 Recalling a Memory Channel
1. Select the Memory mode by pressing the
key. "
" and channel number
appear on the display to indicate that the unit is in the Memory mode.
Repeat to switch between the Memory, Call channel and VFO modes.
2. Select a memory channel.
Rotating the main dial will increase or decrease a memory channel number.
4.5.3 Deleting a Memory Channel
1. Select the Memory mode by pressing the
key.
2. Rotate the dial to select the memory channel No. that you wish to delete.
4
3. Press the FUNC key, and while
is displayed on the LCD, press the
key. A
beep sounds, then "
" flashes on the display. If
disappeared before pressing
the
key, press the FUNC key again and then
key.
NOTE:
When "
" is flashing in step 3 (when the memory contents are displayed as is
on the display), it is still possible to cancel the operation by pressing the FUNC
key, and while
is displayed on the LCD, press the
key. After changing
channels or modes, this is no longer possible.
4.5.4 How to Program Call Channel
1. Select the Memory mode by pressing the
key. "
" appears on the display.
2. Rotate the dial to display " ".
3. Press the
key twice to switch to the VFO mode, and rotate the dial to select the
desired frequency and set other parameters.
4. Press the FUNC key and while
is displayed, press the
key. A beep sounds
and programming is completed. If
disappeared before pressing the
key,
press the FUNC key again and then
key.
4.5.5 Programming a Repeater-Access Function Setting
The "Repeater-Access" function is to set the desired shift and tone parameters to the current
operating frequency by just 2 key-touches. Parameters programmed in the Repeater-Access
function memory can be used in any of the VFO/Memory/Call channel modes.
Although parameters programmed in the Set mode are maintained at any frequency,
those programmed in the Repeater-Access function memory are applied to the
operating frequency only by using the Repeater-Access function (page 41). Thus, it is
recommended that you use this function in amateur radio where you communicate by
frequently switching between simplex and semi-duplex operations.
28
4.Basic Operation
1. Select the Memory mode by pressing the
key, then rotate the dial to select
.
2. The
(minus) and
icons appear on the display. By default, the values are:
DJ-S17E/TFH: minus shift, 0.6MHz offset, 88.5Hz CTCSS tone
DJ-S47E: minus shift, 7.6MHz offset, 88.5Hz tone
If these are the values you desire, no further setting is required so simply press the
key
to go back to the operation mode. Refer to "Repeater-Access" on page 41 for operation.
3. To change the values instead, repeat the same setting sequence explained on page
26 for shift direction and offset frequency then page 37 for CTCSS tone by entering
to the Set mode while
is displayed. Even if you desire the same
values you set for the respective parameters in the VFO mode, please repeat the
sequence in here to activate the Repeater-Access function.
4. After having completed the programming in the Set mode, return to the
menu by pressing any key except FUNC or MONI. Press the FUNC
key and while
is displayed, press the
key. A beep sounds and the new values
are stored in the
memory.
4
NOTE:
・ You can not communicate in the
channel.
・ The
channel is skipped during scanning. You can not delete or
convert this memory to other purposes.
4.5.6 Programmable Parameters in Memory Channels
The following parameters can be stored in each of the memory channels.
• Frequency
• Offset frequency *
• Skip channel setting
• Shift direction (+/-) *
• Busy channel lockout (BCLO)
• Tone encoder frequency *
• Transmission power (H/L)
• Tone decoder frequency *
• Battery save setting
• Tone encoder/decoder setting (TSQ) *
• Clock Shift setting
• DCS code *
• Alphanumeric channel tag
• DCS setting *
• Attenuator Level
NOTE:
Only parameters marked "*" are programmable in Repeater-Access function memory.
29
4.Basic Operation
4.6 Call-Channel Mode
This mode is used to recall a most frequently used memory channel (stored in MC
channel) with a single key-touch.
1. Press the
key.
" " is displayed on the LCD, and the channel
programmed in MC is recalled.
2. Press the
key again in the Call mode to return
to original operating mode (VFO/memory).
4
NOTE:
Refer to "How to Program Call Channel" on page 28 for programming Call channel.
IMPORTANT NOTE:
• The dial operation of frequency/memory channel is blocked in the Call mode.
• It is possible to temporary change the offset and CTCSS/DCS related
parameters in the Call mode by entering to the Set mode in the Call channel.
• The Scan function is deactivated in the Call mode.
• The CALL channel reprogramming is possible but it can't be deleted from the
memory channel mode.
4.7 Receiving
1. Turn on the unit.
2. Press the
3. Press the
key and rotate the dial to adjust the audio level as necessary.
key and rotate the dial to adjust the squelch level.
4. Select the frequency that you wish to operate by using the dial. When a signal is received
on the frequency that you selected,
and S-meter are displayed on the LCD, then
the received signal can be heard. The green RX indicator also lights at this time.
4.7.1 Monitor Function
In case the receiving signal is weak and the audio is intermittently cut off by the
squelch, press the MONI key. As long as this key is pressed, the squelch including
TSQ/DCS unmutes making the audio easier to hear.
• The squelch is unmuted while the MONI key is pressed, regardless of the squelch
level setting.
• This function unmutes the squelch even if the DCS and Tone Squelch functions are set.
30
4.Basic Operation
4.8 Transmitting
1. Select the frequency that you wish by using the dial.
2. Press the PTT key.
The red TX indicator turns on while transmitting.
3. While holding down the PTT key, speak into the unit at normal voice from the
distance of 5cm (2").
4. Release the PTT key to receive.
IMPORTANT NOTE:
• To transmit a tone-burst signal, press the MONI key while holding down the
PTT key.
• Speaking too loud, too close or too far from the unit may distort the audio.
• This unit is equipped with a special kind of cloth over the built-in microphone
for water proof. For this reason, a slight change of tone may happen when you
use accessories like external microphones, but this is not abnormal.
• "OFF" appears on the display and a beep sounds when the PTT key is pressed
with the TX frquency set out of the TX range. You can not transmit in this state.
4
4.8.1 Selecting the Output Level
Press the FUNC key, and while
is displayed on the LCD, press the
key to
switch between high and low transmission power output.
When the low power output is selected, "
" is displayed on the LCD (nothing is
displayed when the high power is selected).
The initial setting is low power.
The Power-meter display is
when transmitting at the low power, and
when transmitting at the high power.
IMPORTANT NOTE:
The output level can't be altered while transmitting.
31
5.Useful Functions
5. Useful Functions
5.1 Scan Modes
The scan function automatically searches the receiving signals. There are 2 modes for
scan-resume condition.
• Timer Scan : The scan stops when a signal is detected, and resumes scanning after 5
(default)
seconds regardless of receiving status.
• Busy Scan: The scan stops when a signal is detected, stays until the signal is gone
then resumes scanning.
During scanning, the 1MHz decimal point ( ) on the frequency display flashes.
Press any key other than the MONI key to stop scanning.
Scanning starts in the direction of the last dial operation (up or down).
5
NOTE:
Please refer to the Set mode to switch the setting between Timer and Busy scan modes
(page 43).
5.1.1 VFO-Scan
1. Press the
key to select the VFO mode.
2. Press the
key for more than 2 seconds to start scanning. The unit scans in
accordance with the order of one step.
3. Rotate the dial clockwise/counter-clockwise to change the scan direction.
VFO-scan scans the entire frequency range.
4. Press any key other than the MONI key to stop scanning.
5.1.2 Memory-Scan
1. Press the
2. Press the
key to select the Memory mode.
key for more than 2 seconds to start memory scanning.
3. Rotate the dial clockwise/counter-clockwise to change the scan direction.
Memory-scan scans all programmed memory channels.
4. Press any key other than the MONI key to stop scanning.
NOTE:
Please set the squelch level correctly before scanning, even in the TSQ scanning the
normal squelch level adjustment is required to activate this function.
32
5.Useful Functions
5.1.3 Setting Skip Channels
You can select the memory channels that you wish to skip during the memory-scan.
1. Select the memory channel in the Memory mode that you wish to skip.
2. Press the FUNC key for more than 2 seconds to enter the Set mode, and select the
menu 16 to display the current skip channel setting.
3. Rotate the dial to switch between ON and OFF. Select ON to set the memory
channel as a skip channel.
4. The 10MHz decimal point appears for the memory channel that is set as a skip channel.
NOTE:
The Call channel and Repeater-Access memory are automatically skipped
during scanning.
5.2 Keylock
5
Press the
key for more than 2 seconds to set the Keylock function on, and repeat
the same to quit.
When the Keylock is on, the
is displayed on the LCD.
When the Keylock is on, other than the following, all operations are blocked.
* PTT
* LAMP * MONI * VOL
* SQL
* Tone-burst
* POWER ON/OFF
NOTE:
Keylock function can't be activated on the Repeater-Access function memory
channel.
5.3 Tone-Burst
This function is to generate an audible tone to access repeaters mostly used in Europe.
• To output the tone-burst tone, press the MONI key while holding down the PTT key.
The tone is transmitted as long as the MONI key is pressed.
The initial setting for the tone-burst tone is 1750Hz, but this can be changed in the
Set mode (page 44).
• While transmitting the tone-burst tone, the CTCSS/DCS tone is temporary
suspended.
• Even while transmitting the tone-burst tone, you can not hear audio from the
speaker.
33
5.Useful Functions
5.4 Naming Memory Channels
In the Memory mode, it is possible to display up to 6 alphanumeric characters (Nametag) instead of conventional frequency display.
5.4.1 Setting Name-Tag
1. Select the memory channel.
2. Press the FUNC key, and while
is displayed press the
key.
3. [A ] flashes on the display.
4. Rotate the dial to select a character to be the first digit.
5. Press the
flashing.
5
key to input the next character. The previous character will stop
6. Repeat the same sequence as necessary.
Press the
key during setting to delete all characters.
7. Press any key (except MONI,
,
) to complete the setting.
NOTE:
Only lighted characters (not flashing ones) are programmed. For example, to
program 3 characters, complete the setting when the fourth character is flashing.
To program 6 characters, complete the setting after the first character goes back
to the flashing status.
5.4.2 Using the Channel Name Function
• Programmed memory channels are displayed with alphanumeric characters. The
channel number is displayed as it normally is.
• Press the FUNC key to display the frequency display for 5 seconds. Pressing certain
keys during this 5 sec period may immediately recall the alphanumeric display,
while other keys access their allocated functions.
34
5.Useful Functions
5.5 Auto-Power-Off (APO)
This function prevents an useless battery consumption.
5.5.1 Setting APO
1. Select the menu 15 in the Set mode to display the current APO setting.
2. Rotate the dial to switch between ON and OFF.
3. Selecting ON activates the APO function, and
is displayed on the LCD.
• The initial setting for the APO function is off.
5.5.2 APO Operation
• After having activated the APO and about 30 minutes elapse without any key-operation,
the unit turns off automatically alerting with beep sounds. The time to Auto-Power-Off
is determined by the last key operation only, not the last signal received.
5
5.6 Time-Out-Timer (TOT)
This function automatically stops transmission when a preset time is elapsed.
5.6.1 Setting TOT
1. Select the menu 07 in the Set mode to display the current TOT setting. T-OFF is
displayed by default.
2. Rotate the dial to change the TOT setting time.
The maximum setting for the TOT time is 450 seconds.
3. Press any key other than the MONI or FUNC key to complete the setting.
5.6.2 TOT Operation
When the preset time is about to be elapsed, a beep sounds to alert that the unit is
forced to quit transmitting. Release PTT key to quit transmitting otherwise the TOT
penalty may be activated. Refer to page 45 for TOT penalty time setting.
35
5.Useful Functions
5.7 Lamp
Press the FUNC key, and while
is displayed on the LCD, press the MONI key to
illuminate the display and keypad.
• The backlight automatically switches off if there is no key operation for 5 seconds.
• Pressing any key other than the LAMP key extends the LAMP function for another 5
seconds.
• Turning on the power while pressing the MONI key illuminates the backlight
permanently. Repeat the same to turn it off.
• When the lamp is set for the "permanent-on" position, pressing the FUNC key then
the MONI key to turn on/off the backlight.
NOTE:
The LAMP function consumes battery. The "permanent-on" position is
recommended only for the operation using an external power source.
5
36
6.Selective Calling
6. Selective Calling
■ Selective Calling Operations
• To communicate only with selected stations, use either the Tone Squelch or the DCS
function.
The Tone Squelch function unmutes the squelch only when a signal added with one
of the matching 39 CTCSS tone frequencies is received.
• The DCS function unmutes the squelch only when a signal added with one of
matching 104 digital codes is received.
• It isn't possible to use the Tone Squelch and DCS functions at the same time.
6.1 Tone Squelch (TSQ)
6.1.1 Setting the Tone Squelch
1. Select the menu 12 in the Set mode to display the current TSQ setting.
2. Rotating the dial, the display changes as below:
TN-OFF
TN-ENC
6
TN-TSQ
• When only
is displayed, the unit encodes the CTSS tone.
• When
is displayed, the unit encodes and decodes the CTCSS tone.
3. Press any key other than the MONI or FUNC key to complete setting.
6.1.2 Setting the Tone Frequency
1. Select the menu 13 in the Set mode to display the current tone frequency.
2. Rotate the dial to select one of the 39 CTCSS tones shown below. The tone can be
set for encode/decode separately (refer to page 38 for details).
67.0
94.8
131.8
186.2
69.3
97.4
136.5
192.8
71.9
100.0
141.3
203.5
74.4
103.5
146.2
210.7
77.0
107.2
151.4
218.1
79.7
110.9
156.7
225.7
82.5
114.8
162.2
233.6
85.4
118.8
167.9
241.8
(unit: Hz)
88.5
91.5
123.0 127.3
173.8 179.9
250.3
3. Press any key other than the MONI or FUNC key to complete the setting.
Observe that
is displayed if you selected TN-ENC in the menu 12.
Observe that both
are displayed if you selected TN-TSQ in the menu 12.
37
6.Selective Calling
6.1.3 Switching Off the Tone Squelch
Select TN-OFF in the menu 12 of the Set mode, and press any key other than the
MONI or FUNC key to complete setting.
6.1.4 To Differentiate the ENC/DEC Tones
To set the encoding and decoding tones independently, perform the following settings.
1. To set the encoding tone, while
is displayed in the setting menu 12, press the FUNC
key to move to the menu 13 and select a desired encoding tone by rotating the dial.
2. Press the MONI key to go back to the menu 12 then rotate the dial clockwise to
select TN-TSQ. Press the FUNC key to move to the menu 13 again and select a
desired decoding tone frequency using the dial.
3. Press the PTT key to return to the operating mode or the FUNC/MONI keys to
continue with setting programming in the Set mode.
6.1.5 Tone Squelch Operation
The squelch unmutes only when the signal with the same decoding-setting tone is
received.
6
6.2 DCS
6.2.1 Setting the DCS
1. Select the menu 14 in the Set mode to display the current DCS setting. The initial
setting is DCS-OF.
Rotating the dial, the display switches between:
DCS-OF
DCS
DCS
023
754
2. Press any key other than the MONI or FUNC key to complete the setting. Observe
that "
" is displayed.
38
6.Selective Calling
6.2.2 Changing the DCS Code
1. In the menu 14 of the Set mode, rotate the dial to select the desired DCS code.
2. Press any key other than the MONI or FUNC key to complete the setting.
• The same DCS code is set for ENC/DEC, differential setting isn't available.
One of the following 104 DCS codes can be selected.
023
025
026
031
032
036
043
054
065
071
072
073
074
114
125
131
132
134
143
145
152
165
172
174
205
212
223
225
245
246
251
252
255
261
263
274
306
311
315
325
331
332
356
364
365
371
411
412
413
445
446
452
454
455
462
464
506
516
523
526
532
546
565
627
631
632
654
662
664
703
732
734
743
754
047
115
155
226
265
343
423
465
606
712
6.2.3 Switching Off DCS
Select DCS-OF in the menu 14 of the Set mode to turn it off.
051
116
156
243
266
346
431
466
612
723
053
122
162
244
271
351
432
503
624
731
6
6.2.4 DCS Operation
The squelch unmutes only when the unit receives the matching code.
39
7.Special Functions
7. Special Functions
7.1 ATT (Attenuator)
Use this function when the receiving signal is interfered by strong signals of nearby
channels. When you activate this function, the transceiver attenuates the receiving
sensitivity.
1. Select the menu 17 in the Set mode to display the current ATT setting.
2. Rotate the dial to change the ATT level. There are 2 levels; ATT-1 attenuates the
received signal by 10dB and ATT-2 does 20dB. Press any key other than the MONI
or FUNC key to complete setting. Observe that "
" appears on the display.
ATT-OF
ATT-1
ATT-2
Select ATT-OF in the setting sequence, and then press MONI or FUNC key to turn
off this function. Observe that "
" disappears from the display.
7.2 Battery Refresh
7
Repeating improper recharge of the Ni-MH battery pack may cause so-called the
"memory effect" that the battery holds less charge. To avoid this, it is always
recommended to fully discharge the battery pack then full charge. This function helps
discharging the battery pack. Please remove the unit from a charger or a DC cable
before this operation.
1. Activate the Keylock (page 33).
2. Press the FUNC key, and while
is displayed,
press the
key twice, the
key twice, the
key twice, and then the
key twice.
"DISCHG" will be displayed on the LCD, and the
battery-refresh starts.
3. To cancel this operation, just turn off the unit, turn it on again, then unlock the
Keylock function.
4. The unit will turn off automatically when finished the refresh.
40
7.Special Functions
Caution
• The time to refresh totally depends on the remaining charge of the battery
pack. To discharge the fully-charged EBP-65 may take up to approx. 7 hours.
• When this function is on, the backlight and the keys are illuminated, and
noise from the speaker can be heard.
• Before storing the rechargeable battery pack for an extended period of
time, please full-charge it after this operation. Also, refresh and fully charge
the battery once every 6 months to keep the pack in good condition.
7.3 Repeater-Access
1. In the VFO/Memory/Call channel mode, select the channel to which you wish to
apply the Repeater-Access setting.
2. Press the FUNC key, and while
is displayed on the LCD, press the
The Repeater-Access setting is applied to the operating frequency.
key.
NOTE:
Preset parameters on the Repeater-Access function memory will be effective at
any frequency. Repeater-Access parameters have priorities over the parameters
programmed in the VFO/memory/CALL modes.
7
41
8.Set Mode
8. Set Mode
The Set mode is used to customize the various operational parameters of your DJS17/47.
8.1 Set Mode Operation
This chart shows the available parameters in the Set mode.
8
Menu
01
Default setting
BS-ON
Function
Battery Save ON/OFF
02
TIMER
Timer/Busy scan setting
03
BEP-ON
Beep sound ON/OFF
04
1750
Tone-Burst Frequency setting
05
SFT-OF
CPU Clock Frequency shift ON/OFF
06
BCL-OF
Busy Channle Lock Out ON/OFF
07
T-OFF
TOT (Time-Out-Timer) setting
08
TP-OFF
TOT Penalty setting
09
STP-5
Tuning Step setting
10
SFD-OF
Shift Direction setting
11
0.600 (7.600)
Offset Frequency setting
12
TN-OFF
Tone Squelch setting
13
88.5
Tone Frequency setting
14
DCS-OF
DCS setting
15
APO-OF
APO (Auto-Power-Off) setting
16
SKP-OF
Skip Channel setting
17
ATT-OF
ATT (Attenuator) setting
18
CHG-ON
Battery Charge ON/OFF
19
BAT-NI
Battery type setting
FUNC key
MONI key
42
8.Set Mode
8.2 Entering the Set Mode
1. Press the FUNC key for at least 2 seconds.
The unit enters the Set mode.
"BS-ON" is displayed as a factory-default.
2. Press the MONI key or FUNC key to select a menu.
The Monitor function can't be used in this status.
3. Rotate the dial to change the parameter.
4. Press any key other than the MONI key and FUNC key to complete the settings, or
use the MONI or FUNC keys to continue programming.
The last operated menu will be selected the next time you enter the Set mode.
8.3 Available Parameters
8.3.1 Menu 1 Battery Save (BS) Function
This function prevents useless battery consumption by switching the power ON/OFF
at a fixed ratio if there is no key operation or receiving signal for a continuous period
of 5 seconds or more.
1. BS-ON is displayed on the LCD.
2. Rotate the dial to select the battery save setting (on or off).
• The factory setting is BS-ON
• The Battery Save function is temporarily suspended when a key is operated or a
signal is received.
8
• Set this parameter OFF for packet operation.
• The display remain unchanged even the BS function is in the OFF cycle.
8.3.2 Menu 2 Timer/Busy Scan Setting
Select the scan-resume condition in this menu (page 32).
1. TIMER is displayed on the LCD.
2. Rotate the dial to select the scan-resume condition between TIMER and BUSY.
43
8.Set Mode
8.3.3 Menu 3 Beep Function
Select OFF to turn off all the beep sounds inclusive of alerting beeps.
1. BEP-ON is displayed on the LCD.
2. Rotate the dial to select the beep setting on and off.
8.3.4 Menu 4 Tone-Burst Frequency Setting
1. 1750 is displayed on the LCD.
2. Rotate the dial to select the tone-burst frequency.
8.3.5 Menu 5 Clock Shift Setting
In the unlikely event that you may hear a weak noise always on the same frequency, it
may be so-called a CPU-clock noise. Unfortunately this is due to the circuit-design of
this product and can't be eliminated, but can be moved away to another frequency.
1. SFT-OF is displayed on the LCD.
2. Rotate the dial to select the clock shift setting on and off.
8
44
NOTE:
This function isn't a noise-blanker. Also, since not all noises are due to a CPUclock noise, the clock shift setting may not be effective.
8.Set Mode
8.3.6 Menu 6 Busy Channel Lockout Setting
This function restricts the PTT (transmit) operation.
1. BCL-OF is displayed on the LCD.
2. Rotate the dial to select the Busy Channel Lockout setting on and off.
When Busy Channel Lockout is set to on, transmission is possible only in the
following conditions (and isn't possible otherwise).
The alarm sounds if the PTT key is pressed when transmission is prohibited.
1) When no signal is being received (BUSY isn't displayed).
2) When the tone matchs and the squelch is unmuted based on the Tone Squelch
setting conditions.
3) When the codes match and the squelch is unmuted based on the DCS setting
conditions.
8.3.7 Menu 7 TOT (Time-Out-Timer) Setting
Refer to "Time-Out-Timer (TOT)" on page 35.
8.3.8 Menu 8 TOT Penalty Time
This parameter determines the time to resume the transmission after the unit is forced
to quit transmitting by TOT.
1. TP-OFF is displayed on the LCD.
2. Rotate the dial to change the TOT Penalty Time setting.
8
Transmission is prohibited until the penalty time elapses.
• An alert beep sounds when the PTT key is pressed during the penalty time.
8.3.9 Menu 9 Tuning Step Setting
Refer to "Setting the Tuning Step" on page 25.
8.3.10 Menu 10 Shift Direction Setting
Refer to "Shift Direction and Offset Frequency Settings" on page 26.
8.3.11 Menu 11 Offset Frequency Setting
Refer to "Shift Direction and Offset Frequency Settings" on page 26.
45
8.Set Mode
8.3.12 Menu 12 Tone Squelch Setting
Refer to "Setting the Tone Squelch" on page 37.
8.3.13 Menu 13 Tone Frequency Setting
Refer to "Setting the Tone Frequency" on page 37.
8.3.14 Menu 14 DCS Setting
Refer to "Setting the DCS" on page 38.
8.3.15 Menu 15 APO (Auto-Power-Off) Setting
Refer to "Setting APO" on page 35.
8.3.16 Menu 16 Skip Channel Setting
Refer to "Setting Skip Channels" on page 33.
8.3.17 Menu 17 ATT (Attenuator) Setting
Refer to "ATT (Attenuator)" on page 40.
8.3.18 Menu 18 Battery Charge Function
The Ni-MH battery pack can be charged with an external power supply or an optional
AC adapter using the DC-jack on the unit. Please select ON to activate this function.
The factory setting is ON.
1. CHG-ON is displayed on the LCD.
2. Rotate the dial to select the battery charge setting on and off.
3. Please be sure to read "Battery Type Setting " (page 47) to correctly use this function.
8
Caution
• Please be sure to select OFF when using a dry cell case otherwise it may
risk a leak of battery liquid, heat or explosion of the battery cells and the
battery case.
• While this function is activated, without attaching a battery pack or the
remaining battery level is below the usable range, the unit turns on by just
connecting the DC source such as an adapter or a DC cable (without
operating the power key). Therefore, leaving the battery pack detached from
the unit may cause the charging terminals on the back of the unit to short
out. Please be very cautious when you operate with an external DC source.
46
8.Set Mode
8.3.19 Menu 19 Battery Type Setting
Select the correct battery type from Ni-MH battery pack, Li-ion battery pack and
Alkaline (and Oxyride) dry cells in order to display the battery-level icon correctly
and to perform the battery-charge using the DC-jack.
1. BAT-NI is displayed on the LCD.
2. Rotate the dial to select battery type from Ni-MH battery pack (BAT-NI), Li-ion
battery pack (BAT-LI) and Alkaline dry cells (BAT-AL).
BAT-NI
(Ni-MH)
BAT-LI
(Li-ion)
BAT-AL
(Dry cell)
NOTE:
Please set this parameter correctly. When the BAT-LI or BAT-AL is selected,
previously explained battery charge function can't be performed.
8
Tone Squelch
Tone Frequency
DCS
APO (Auto-Power-Off)
Skip Channel
ATT (Attenuator)
Battery Charge
Battery type
13. 88.5
14. DCS-OF
15. APO-OF
16. SKP-OF
17. ATT-OF
18. CHG-ON
19. BAT-NI
10. SFD-OF
12. TN-OFF
Shift Direction
9. STP-5
11. 0.600 (7.600) Offset Frequency
TOT Penalty
Tuning Step
8. TP-OFF
Busy Channle Lock Out
TOT (Time-Out-Timer)
7. T-OFF
CPU Clock Frequency shift
5. SFT-OF
6. BCL-OF
Beep sound
Tone-Burst Frequency setting
4. 1750
Timer/Busy scan setting
2. TIMER
3. BEP-ON
Battery Save
Reference (Set mode)
1. BS-ON
• Cut out the Set Mode Function List below for use as a quick reference.
47
9.Cloning and Packet Operation
9. Cloning and Packet Operation
9.1 Cloning
The memory data and customized operational parameters can be transferred from a
Master unit to other DJ-S17/DJ-S47 (Slave units).
9.1.1 Cable Connection
• Make sure that both units are turned off before connecting the cable.
• Connect the Microphone/Speaker jack on the Master unit with the Slave unit using
an optional clone cable (EDS-11) as shown below, then turn on both units.
To the MIC/SP jack on the Master unit
To the MIC/SP jack on the Slave unit
* Be sure to securely screw the plug all the way down to the bottom of the jack.
9.1.2 Master/Slave Units
Press the PTT key three times while holding down
the MONI key.
"CLONE" is displayed on the LCD, and both units
enter the Clone mode.
9
48
9.Cloning and Packet Operation
9.1.3 Master Unit Operation
1. In the Clone mode, press the PTT key of the
master unit. "SD***" is displayed on the LCD,
and starts the data-transfer.
2. After the transfer is completed successfully,
"PASS" is displayed.
3. Turn off the unit. Repeat the same sequence to
clone more units.
Stop moving the SD***, COMERR etc. on the display means that the cloning is
failed. Please read below and repeat the procedure.
9.1.4 Slave Unit Operation
1. When the data is sent from the master unit,
"LD***" is displayed on the receiving unit, and the
data-transfer starts.
2. After the transfer is completed, "PASS" is
displayed.
3. After the cloning is done, turn off the unit by
pressing the
key and remove the cable.
Repeat the same sequence to clone more units.
In case the transfer fails, please turn off the slave unit and perform the reset sequence
(page 52) to turn on again before retry. If you quit cloning of this slave unit, please reset
it anyway otherwise it may not work properly.
Caution
9
• Don't disconnect the cable during data transmission. If you disconnect the
cable at this time, "COMERR" is displayed on the LCD of the master unit,
and transmission is aborted.
• When data transfer is performed using the Clone function, all settings in the
slave unit are overwritten by the master unit settings.
There is NO data back-up available in unit's memory.
49
9.Cloning and Packet Operation
9.2 Packet Operation
Packet operation is one of the data communication methods, which enables data
transmission and reception with a personal computer through an optional TNC unit.
9.2.1 Packet Operation Connections
Connect an optional EDS-10 Microphone/Speaker cable plug to the MIC/SP jack on
the top of the unit, and connect the TNC (Terminal Node Controller) to the SP jack
with 3.5Ø plug, and to MIC jack with 2.5Ø plug on the EDS-10 as shown below.
• Input level adjustment: The unit doesn't have microphone and speaker level
adjustment circuit. Adjust their level on the TNC side.
• Output level adjustment: Use the audio output (
key) of the unit to adjust the
output level from MIC/SP terminal.
EDS-10 jack
Optional TNC
3.5ø PLUG
SP
T
SP jack 3.5ø
GND
N
MIC
C
PTT
GND
(Low)
10µF
2.5ø PLUG
MIC jack 2.5ø
10kΩ
5.0V
DJ-S17/47
EDS-10 plug
3
2
5.0V
1
SP
MIC
9
SP
GND
GND
MIC
5V OUT
1
2
3
*Power is supplied from internal 5V line through 100Ω resistor.
Caution
• Refer to the TNC's instruction manual when connecting the TNC unit to other
devices (personal computer etc.). If the unit, TNC unit and connected personal
computer are set too close, noise between them may cause interference.
• Turn the battery save function off during packet operations.
• DJ-S17/DJ-S47 operates up to 1200bps only.
50
10.Maintenance and Reference
10. Maintenance and Reference
10.1 Troubleshooting
Please check the list below before concluding that the unit needs to be serviced. If a
problem persists, please reset the unit. The setting/CPU program-related troubles are
often resolved by the reset.
Symptom
Possible Cause
Nothing appears on Poor battery pack
the display when
connection.
turning on the power. Battery is exhausted.
You are releasing the
key too quickly.
No Speaker audio.
Volume too low.
No reception.
Squelch level too high.
Tone squelch is on.
DCS is on.
You are pressing the PTT
key and transmitting.
Frequency display is CPU error.
incorrect.
A channel name is
set.
Won't scan.
Squelch is unmuted.
Frequency and
Keylock is on.
memory number
Transceiver is in the
don't change.
Call mode.
Key entry not possible. Keylock is on.
Incorrect setting of
Repeater-Access
parameters.
can't be used.
Battery is exhausted.
Can't transmit.
Display flashes or goes
out when you transmit.
Not pressing the PTT
Can't transmit.
key firmly enough.
Can't talk to other
Off-frequency.
stations.
The display flashes
or disappears during
reception.
Action
Check that the battery pack terminals are
clean, and pack is correctly attached.
Recharge or replace the battery.
Hold the power key down until the display
shows figures.
Adjust the audio level.
Adjust the squelch.
Turn off tone squelch.
Turn off DCS.
Release PTT key.
Reset the unit.
See Naming Memory Channels function
(page 34).
Set squelch so that noise mutes.
Turn off Keylock.
Select the VFO or Memory mode.
Turn off Keylock.
Set the correct parameters to suit your
local repeaters.
Recharge or replace the battery.
Press the PTT key and confirm that TX/RX
lamp lights red.
Be sure that you are in the TX range
and/or check shift status.
Incorrect frequency. Check the shift status/repeater settings.
Battery is exhausted. Recharge battery or replace the battery.
10
* Please be advised that the water-proof shields including jack caps are subject to
consume. The factory warranty for IPX7-grade water-proof is 1 year. Please
consult with your local dealer when further service-assistance may be necessary.
Please visit alinco.com's "DISTRIBUTION" menu to locate the nearest dealer.
51
10.Maintenance and Reference
10.2 Resetting
When you reset the unit, all settings are returned to the initial factory settings. The
reset deletes the programmed memory channels also.
1. Turn on the unit with the FUNC and
keys pressed together.
2. All the icons appear on the display.
Release the keys. All display will disappear for 2 seconds, and then reappear. The
initial mode is the VFO.
Factory default settings
VFO Frequency
CALL Frequency
Memory Channel
Channel Step
Shift
Offset Frequency
Tone Setting
Tone Frequency
DCS Setting
DCS Code
Transmitter Output
Auto Dialer Code
Keylock
Time-Out-Timer
Auto-Power-Off
Volume Level
Squelch Level
Repeater Shift
Repeater Offset Frequency
Repeater Tone Setting
DJ-S17E
145.000MHz
145.000MHz
0~199ch Blank
12.5kHz
None
0.6MHz
None
88.5Hz
None
023
Low
None
off
off
off
0
0
0.6MHz
88.5Hz
DJ-S17TFH
155.000MHz
155.000MHz
0~199ch Blank
5kHz
None
0.6MHz
None
88.5Hz
None
023
Low
None
off
off
off
0
0
0.6MHz
88.5Hz
DJ-S47E
435.000MHz
435.000MHz
0~199ch Blank
12.5kHz
None
7.6MHz
None
88.5Hz
None
023
Low
None
off
off
off
0
0
7.6MHz
88.5Hz
NOTE:
THE RESET DELETES ALL THE MEMORIES.
Please take notes of the important data and keep it for future reference.
10
52
10.Maintenance and Reference
10.3 Options
EBP-63
Li-ion Battery Pack (DC 7.4V 1100mAh)
EBP-64
Li-ion Battery Pack (DC 7.4V 1600mAh)
EBP-65
Ni-MH Battery Pack (DC 7.2V 700mAh)
EBP-66
Ni-MH Battery Pack (DC 7.2V 2000mAh)
EDC-36
Mobile Cigarette Lighter Adapter with Active Noise Filter
EDC-37
External DC Power Supply Cable
EDC-43
Mobile Cigarette Lighter Cable for Charging Ni-MH Packs
EDC-143E/UK
Trickle Battery Charger (E: 230V UK: 230V UK plug)
EDC-143R
Multiple-Charger Basket (An external DC power supply required)
EDC-144E/UK
Rapid Battery Charger (E/UK: same as above)
EDC-144R
Multiple-Charger Basket (An external DC power supply required)
EDC-147
Wall Charger (230V)
EDC-148
Wall Charger (230V) U.K. Plug
EDH-34
Dry Cell Case
EDS-10
Microphone/Speaker Cable
EDS-11
Clone Cable
EME-6
Earphone *
EME-12
Headset with VOX *
EME-13
Earphone and MIC with VOX *
EME-15
Tie-pin MIC with VOX *
EME-20
Earphone Microphone *
EME-32A
Earphone microphone (EDS10 NOT required)
EMS-47
Speaker Microphone with Audio Control *
EMS-59
Speaker Microphone *
EMS-62
Speaker Microphone (EDS10 NOT required)
ESC-41
Soft Case
・ Please purchase an optional EDS-10 cable to operate optional accessories marked *.
NOTE:
FOR EUROPEAN USERS:
Please be advised that some of the accessories listed above are not RoHS
compliant at the moment this manual has been edited, and they are intended for
the sales to where RoHS order is not effective. Please consult with your local
dealer for any updates about RoHS compliance of our products before purchase.
Use of external power source cables are at your own risk per IEC/EN60950-1.
Please refer to "Limited Power Source" on page 8 for details.
10
IMPORTANT NOTE:
All accessories except EBP-63/64/65/66 and soft cases above listed are NOT
water-proof. Never use these accessories in wet conditions.
53
10.Maintenance and Reference
• When using EDC-36, EDC-37, EDC-43, EDC-146, EDC-147, EDC-148, connect
them to the unit first before turning on the unit.
• EBP-63, 64, 65 and 66 are IPX7-grade water-proof only when correctly attached and
used with DJ-S17/DJ-S47.
10.3.1 Microphone/Speaker Cable (EDS-10)
1. Turn off the unit.
2. Turn the plug clockwise until it stops. Check to be
sure it is securely connected.
3. Connect the Microphone/Speaker plugs to the each
jack.
10.3.2 Battery Packs
The battery packs aren't fully charged when shipped.
Please charge the pack completely before use.
■ Available Battery Packs for DJ-S17/DJ-S47:
EBP-63
Li-ion Battery Pack (DC 7.4V 1100mAh)
EBP-64
Li-ion Battery Pack (DC 7.4V 1600mAh)
EBP-65
Ni-MH Battery Pack (DC 7.2V 700mAh)
EBP-66
Ni-MH Battery Pack (DC 7.2V 2000mAh)
■ Charging Battery Packs
Refer to the chart below for the combination of the proper battery pack and charger.
The ○ indicates the usable combination, (* hrs) means the approximate time
necessary to full charge the empty pack.
10
54
Li-ion Battery Pack
Battery Packs
EBP-63
EBP-64
Chargers
Trickle Charger EDC-143
(2hrs)
(3hrs)
Rapid Charger EDC-144
Wall Charger EDC-147/148
Ni-MH Battery Pack
EBP-65
EBP-66
(10hrs)
(14hrs)
(1.5hrs)
(3.5hrs)
(10hrs)
(30hrs)
10.Maintenance and Reference
10.3.3 Using the Chargers
Caution
Please also read the "Warning" (page 4 of this manual) and the safety
instruction that is included in the accessories' package before operating for
your safety.
■ Charging with the EDC-143 (Trickle Charger)
Please make sure that following items are included in the package.
• EDC-143E: EDC-143 basket, EDC-147 adapter (AC 230V), insulation sheet
• EDC-143UK: EDC-143 basket, EDC-148 adapter (AC 230V), insulation sheet
• EDC-143R: EDC-143 basket, connection cable, insulation sheet, 2 screws,
connective stay
Caution
Before using them for the first time, attach the insulation sheet to cover the
screw-terminals at the bottom to avoid short-circuiting. Please refer to page 60
for instruction.
1. Connect the AC adapter plug to the DC-IN jack on
the back of the basket.
*The design of the AC adapter may vary
depending on the models.
2. Connect the adapter to an outlet.
10
55
10.Maintenance and Reference
3. Press the sides of the adjustment plate, and attach
it to the proper grooves of the basket according to
the size of the battery pack. Make sure that the
characters A, B and C on both sides of the stand
match each other and the plate is placed all the
way down to the bottom.
Installation Positions of the Adjustment Plate
When mounting only the
battery (EBP-65)
A
B
C
A
B
C
A
B
C
EBP-66
A
B
C
EBP-65
When mounting the battery
attached to the unit (EBP-65)
When mounting only the
battery (EBP-66)
When mounting the battery
attached to the unit (EBP-66)
4. Mount the battery (with or without being attached
to the unit) in the basket as shown. Turn off the
unit while charging.
The red indicator on the basket turns on and
charging starts.
10
56
NOTE:
You can charge the battery pack using a basket (EDC-143/144) even if the
battery charge function is set to "CHG-OF".
10.Maintenance and Reference
5. After charging time is elapsed (page 54), remove the battery pack from the basket.
The red indicator stays turned on as long as the pack is mounted on the basket
regardless of the charging status.
Specifications
*The charging time may vary depending on the condition of the battery pack and the
temperature of the environment.
NOTE:
Refer to page 59 for information about how to charge the battery using
addtional baskets.
■ Charging with the EDC-144 (Quick Charger)
Please make sure that following items are included in the package
• EDC-144E: EDC-144 basket, EDC-151 adapter (AC 230V), insulation sheet
• EDC-144UK: EDC-144 basket, EDC-152 adapter (AC 230V), insulation sheet
• EDC-144R: EDC-144 basket, connection cable, insulation sheet, 2 screws,
connective stay
Caution
Before using them for the first time, attach the insulation sheet to cover the
screw-terminals to avoid short-circuiting. Please refer to page 60 for instruction.
1. Connect the AC adapter plug to the DC-IN jack on
the back of the basket.
*The design of the AC adapter may vary
depending on the models.
10
2. Connect the adapter to an outlet.
57
10.Maintenance and Reference
3. Press the sides of the adjustment plate, and attach
it to the proper grooves of the basket according to
the size of the battery pack. Make sure that the
characters A, B and C on both sides of the stand
match each other and the plate is placed all the
way down to the bottom.
Installation Positions of the Adjustment Plate
When mounting only the
battery (EBP-63/65)
A
B
C
A
B
C
A
B
C
EBP-66
A
B
C
EBP-64
When mounting the battery
attached to the unit (EBP-64)
EBP-63/65
When mounting only the
battery (EBP-64)
When mounting the battery
attached to the unit
(EBP-63/65)
When mounting only the
battery (EBP-66)
When mounting the battery
attached to the unit (EBP-66)
4. Mount the battery (with or without being attached
to the unit) in the basket as shown. Turn off the
unit while charging.
The red indicator on the basket turns on and
charging starts.
10
58
NOTE:
You can charge the battery pack using a basket (EDC-143/144) even if the
battery charge function is set to "CHG-OF".
10.Maintenance and Reference
5. The red indicator turns off when the charge is completed. Remove the battery pack
from the basket.
NOTE:
The flashing red indicator means that the charger isn't working properly. Stop
using it immediately, remove the cord form the outlet and consult with your
local Alinco dealer.
Specifications
*The charging time may vary depending on the condition of the battery pack and the
temperature of the environment.
■ Connecting Additional Baskets (EDC-143R/144R)
In order to use EDC-143R and EDC-144R, an optional power supply (IEC/EN 609501 compliant) of 1A/5A minimum respectively is required.
A DC cable isn't included in the package; the suggested DC cable is 20 AWG wire,
shorter than 1m (3feet) in length.
1. Make sure that the output voltage of the power supply is DC 12.0V.
2. Connect the terminals with the provided
connection cable, the red cable to the positive and
the black cable to the negative terminals.
The additional basket can be connected up to 5 in
the same way.
3. Connect the ends of the DC cable to the terminals
of the basket.
* This DC cable isn't provided in the products.
10
59
10.Maintenance and Reference
4. Attach the connective stay and the insulation
sheets to cover the terminals to avoid shortcircuiting.
Caution
This insulation sheet marked * is provided to all EDC-143/144 series chargers.
Please be sure to cover the bottom of the charger with this sheet as shown
above to prevent short-circuiting before using them for the first time.
5. Connect the other ends of the DC cable to the
output terminals of the power supply.
Be mindful to the polarities of the terminals.
10
60
11.Specifications
11. Specifications
■ General<DJ-S17>
Frequency range
E:
TX144~145.995MHz * 144~145.995MHz
RX144~145.995MHz * 144~145.995MHz
TFH: TX136~173.995MHz * 150~173.995MHz
RX130~173.995MHz * 150~173.995MHz
* Guaranteed range per specifications
Modulation:
F3E (FM)
Frequency step:
5, 10, 12.5, 15, 20, 25, 30kHz step
Memory channel:
200 channels + 1 call channel + 1 Repeater-Access
function memory
Ant. impedance:
50 Ω unbalanced
Frequency stability:
±5ppm
Mic. impedance:
2k Ω
Supply voltage:
DC 7.0~16.0V (EXT DC-IN)
Current consumption:
1.4A (typical) Transmit high at 5W
250mA (typical) Receive at 500mW
70mA (typical) Standby
25mA (typical) Battery save on
Temperature range:
External DC: -10°C~+60°C (+14°F~+140°F)
Battery packs: -10°C~+45°C (+14°F~+113°F)
Ground:
Negative ground
Dimension:
58(W)x110(H)x36.4(D)mm
(2.28"(W)x4.33"(H)x1.43"(D))
(with EBP-65)
Weight:
Approx. 280g (9.9oz)
(with EBP-65)
Sub audible Tone (CTCSS): encoder/decoder installed (39 tones)
Sub audible Tone (DCS):
encoder/decoder installed (104 codes)
11
61
11.Specifications
■ Transmitter
Power output:
Modulation:
Spurious emission:
Max. deviation:
Mic. impedance:
■ Receiver
System:
Sensitivity:
Intermediate frequency:
Selectivity
AF output:
11
62
Approx. 5W (with EBP-65)
Approx. 5W (with DC 13.8V)
Approx. 0.8W (LOW output)
Variable reactance
-60dB or less
±5kHz
2k Ω
Double-conversion super heterodyne
-14.0dBµ (0.2µV) or less
1st IF 21.7MHz 2nd IF 450kHz
-6dB:
12kHz or more
-60dB:
26kHz or less
500mW (MAX)
400mW (8 Ω, 10% distortion)
11.Specifications
11■ General<DJ-S47>
Frequency range
E:
TX430~439.995MHz * 430~439.995MHz
RX430~439.995MHz * 430~439.995MHz
* Guaranteed range per specifications
Modulation:
F3E (FM)
Frequency step:
5, 10, 12.5, 15, 20, 25, 30kHz step
Memory channel:
200 channels + 1 call channel + 1 Repeater-Access
function memory
Ant. impedance:
50 Ω unbalanced
Frequency stability:
±2.5ppm
Mic. impedance:
2k Ω
Supply voltage:
DC 7.0~16.0V (EXT DC-IN)
Current consumption:
1.7A (typical) Transmit high at 5W
250mA (typical) Receive at 500mW
80mA (typical) Standby
27mA (typical) Battery save on
Temperature range:
External DC: -10°C~+60°C (+14°F~+140°F)
Battery packs: -10°C~+45°C (+14°F~+113°F)
Ground:
Negative ground
Dimension:
58(W)x110(H)x36.4(D)mm
(2.28"(W)x4.33"(H)x1.43"(D))
(with EBP-65)
Weight:
Approx. 280g (9.9oz)
(with EBP-65)
Sub audible Tone (CTCSS): encoder/decoder installed (39 tones)
Sub audible Tone (DCS):
encoder/decoder installed (104 codes)
11
63
11.Specifications
■ Transmitter
Power output:
Modulation:
Spurious emission:
Max. deviation:
Mic. impedance:
■ Receiver
System:
Sensitivity:
Intermediate frequency:
Selectivity
AF output:
11
64
Approx. 4.5W (with EBP-65)
Approx. 5W (with DC 13.8V)
Approx. 0.8W (LOW output)
Variable reactance
-60dB or less
±5kHz
2k Ω
Double-conversion super heterodyne
-12.0dBµ (0.25µV) or less
1st IF 38.85MHz 2nd IF 450kHz
-6dB:
12kHz or more
-60dB:
26kHz or less
500mW (MAX)
400mW (8 Ω, 10% distortion)
ALINCO, INC.
Head Office:Shin-Dai building 9th Floor
2-6, 1-Chome, Dojimahama, Kita-ku, Osaka 530-0004, JAPAN
Phone:+81-6-4797-2136 Fax: +81-6-4797-2157
E-mail:export@alinco.co.jp
Printed in Japan
Copyright Alinco, Inc. PS0545/FNNJ-EF
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising