Yamaha | RX-V1000RDS | Owner`s manual | Yamaha RX-V1000RDS Owner`s manual

GB
RX-V1000RDS
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
0100V1000RDS-cv1/4
1
RX-V1000RDS
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Printed in Malaysia ID
V641400
9/11/0, 6:04 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 5 cm of ventilation space on the
top, right and left, and at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power
plug from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
5 On the top of this unit, do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Buring objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may cause
electrical shock to the user and/or damage to this
unit.
■ For U.K. customers
6 Do not cover the rear panel of this unit with a
newspaper, tablecloth, curtain, etc. in order not to
obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this
unit, and/or personal injury.
• The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Take care of this unit so that no foreign objects and/
or liquid drops inside this unit.
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION
II
0101V1000RDS_Cau_EN
2
9/5/0, 4:41 PM
INTRODUCTION
CONTENTS
CONTENTS ........................................................... 1
FEATURES ............................................................ 2
GETTING STARTED ........................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS ........................ 4
PREPARATION
SPEAKER SETUP .............................................. 11
Speakers to Be Used ............................................... 11
Speaker Placement ................................................. 11
Before Connecting Components ............................ 12
Connecting Audio Components ............................. 12
Connecting Video Components .............................. 14
Connecting the Speakers ........................................ 16
Connecting to an External Amplifier ..................... 18
Connecting an External Decoder ........................... 18
IMPEDANCE SELECTOR Switch ....................... 19
Connecting the Power Supply Cords ..................... 19
ON-SCREEN DISPLAY (OSD) ......................... 20
SPEAKER MODE SETTINGS ......................... 21
Summary of SPEAKER SET Items
1A through 1F .................................................... 21
ADJUSTING THE SPEAKER
OUTPUT LEVELS ......................................... 22
Before You Begin ................................................... 22
Using the Test Tone (TEST DOLBY SUR.) .......... 23
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ...................................................... 48
SLEEP TIMER .................................................... 49
Setting the Sleep Timer .......................................... 49
Canceling the Sleep Timer ..................................... 49
REMOTE CONTROL FEATURES .................. 50
Control Area ........................................................... 50
Each Component Control Area .............................. 52
Setting the Manufacturer Code .............................. 57
Programming a New Remote Control Function
(Learn Feature) ................................................... 58
Using the Macro Feature ........................................ 60
Changing the Source Name
in the Display Window ....................................... 62
Clearing a Learned Function or Macro .................. 62
Clearing Learned Functions, Macros,
Renamed Source Names,
and Setup Manufacturer Codes .......................... 63
ADVANCED
OPERATION
OSD Modes ............................................................ 20
Selecting the OSD Mode ........................................ 20
Adjusting the Items on the SET MENU ................. 39
1 SPEAKER SET (speaker mode settings) ........... 40
2 LOW FRQ TEST ............................................... 43
3 L/R BALANCE
(balance of the left and right main speakers) ..... 44
4 HP TONE CTRL (headphone tone control) ....... 44
5 CENTER GEQ (center graphic equalizer) ......... 44
6 INPUT RENAME .............................................. 44
7 I/O ASSIGNMENT ............................................ 44
8 INPUT MODE (initial input mode) ................... 45
9 PARAM. INI (parameter initialization) ............. 45
10DOLBY D. SET (Dolby Digital set) .................. 45
11 DTS LFE LEVEL .............................................. 46
126.1/ES AUTO ..................................................... 46
13SP DELAY TIME ............................................... 46
14DISPLAY SET ................................................... 47
15MEMORY GUARD ........................................... 47
BASIC
OPERATION
CONNECTIONS ................................................. 12
SET MENU .......................................................... 39
PREPARATION
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Using the Remote Control ........................................ 8
Front Panel Display .................................................. 9
Rear Panel .............................................................. 10
INTRODUCTION
ADVANCED OPERATION
INTRODUCTION
ADDITIONAL
INFORMATION
ADDITIONAL INFORMATION
BASIC OPERATION
SOUND FIELD PROGRAM ............................. 64
BASIC PLAYBACK ........................................... 24
Input Modes and Indications .................................. 26
Selecting a Sound Field Program ........................... 28
Normal Stereo Reproduction .................................. 29
Hi-Fi DSP Programs ............................................... 64
CINEMA DSP Programs ........................................ 65
MOVIE THEATER Programs ................................ 68
SOUND FIELD PROGRAM PARAMETER
EDITING ......................................................... 69
Connecting the Antennas ........................................ 30
Automatic (or Manual) Tuning .............................. 31
Presetting Stations .................................................. 32
Tuning in to a Preset Station .................................. 33
Exchanging Preset Stations .................................... 34
What is a sound field? ............................................ 69
Sound Field Program Parameters ........................... 69
Changing Parameter Settings ................................. 70
Resetting a Parameter to the Factory-set Value ...... 70
Digital Sound Field Parameter Descriptions .......... 71
APPENDIX
TUNING ............................................................... 30
RECEIVING RDS STATIONS .......................... 35
Description of RDS Data ....................................... 35
Changing the RDS Mode ....................................... 35
PTY SEEK Function .............................................. 36
EON Function ........................................................ 37
TROUBLESHOOTING ..................................... 75
SPECIFICATIONS ............................................. 80
English
BASIC RECORDING ......................................... 38
APPENDIX
1
0102V1000RDS_1-10_EN
1
9/5/0, 4:41 PM
Thank you for selecting this YAMAHA AV receiver.
FEATURES
Built-in 5-Channel Power Amplifier
Other Features
◆ Minimum RMS Output Power
(0.04% THD, 20 Hz – 20 kHz)
Main:
100 W + 100 W (8 Ω)
Center:
100 W (8 Ω)
Rear:
100 W + 100 W (8 Ω)
◆ 96-kHz/24-bit D/A Converter
◆ “SET MENU” which Provides You with
15 Items for Optimizing This Unit for Your
Audio/Video System
◆ Test Tone Generator for Easier Speaker Balance
Adjustment
◆ 6-Channel External Decoder Input for Other
Future Formats
◆ BASS EXTENSION Button for Reinforcing
Bass Response
◆ On Screen Display Function Helpful in
Controlling This Unit
◆ S Video Signal Input/Output Capability
◆ Component Video Input/Output Capability
◆ Optical and Coaxial Digital Audio Signal
Jacks
◆ Sleep Timer
◆ Multi-Function Remote Control
Multi-Mode Digital Sound Field
Processing
◆ Digital Sound Field Processor (DSP)
◆ Dolby Pro Logic decoder
◆ Dolby Digital/Dolby Digital Matrix 6.1
Decoder
◆ DTS/DTS ES Decoder
◆ CINEMA DSP: Combination of YAMAHA
DSP Technology and Dolby Pro Logic, Dolby
Digital or DTS
◆ Virtual CINEMA DSP
◆ SILENT CINEMA DSP
Sophisticated AM/FM Tuner
◆ 40-Station Random Access Preset Tuning
◆ Automatic Preset Tuning
◆ Preset Station Shifting Capability (Preset
Editing)
◆ Multi-Function for RDS Broadcast Reception
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control for such operations, the button name on the remote control is given in
parentheses in this manual.
Manufactured under license from Dolby Laboratories. “Dolby”,
“AC-3”, “Pro Logic”, “Surround EX” and the double-D symbol
are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997 Dolby
Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued and
pending. “DTS”, “DTS Digital Surround” and “DTS ES” are
trademarks of Digital Theater Systems, Inc. Copyright 1996
Digital Theater Systems, Inc. All Rights Reserved.
2
0102V1000RDS_1-10_EN
2
9/5/0, 4:41 PM
GETTING STARTED
INTRODUCTION
Checking the Package Contents
Check your package to make sure it has the following items.
Remote control
Manganese batteries (3)
(AA, R6, UM-3)
AM loop antenna
Indoor FM antenna
Quick Reference Card
MACRO
TRANSMIT RE-NAME
CLEAR
LEARN
MACRO
OFF
ON
SYSTEM
POWER
STANDBY
PHONO
TUNER
MD/TAPE
CD-R
CD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PREPARATION
V-AUX
D-TV/LD
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SELECT
MENU
POWER
REC
SOUND
– CHAPTER +
SEARCH
STOP
PAUSE
PLAY
CHURCH
JAZZ CLUB
/
10KEY DSP
HALL 1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
BASIC
OPERAIONT
MONO
MOVIE
6.1/ES
HALL 2
1
ROCK
CONCERT
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
75-ohm/300-ohm antenna
adapter (U.K. model only)
DISC
RESET button
If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Note
• If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
English
• Change the batteries periodically.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
After you have inserted new batteries, be sure to push
RESET in the battery compartment by using a ballpoint
pen or similar object before using the remote control.
(This does not clear the contents of the memory.)
APPENDIX
■ Notes on batteries
As the batteries lose power, the operating range of the
remote control decreases and the TRANSMIT indicator
does not flash or its light becomes dim. When you notice
any of these conditions, change all of the batteries.
3
0102V1000RDS_1-10_EN
3
ADDITIONAL
INFORMATION
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
■ Changing batteries
ADVANCED
OPERATION
Installing Batteries in the Remote
Control
9/5/0, 4:41 PM
CONTROLS AND FUNCTIONS
Front Panel
1
2
3
4
5
6
INPUT
VOLUME
7
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
EDIT
PHONES
CD
ON
EFFECT
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
PTY SEEK
BASS
TREBLE
PROGRAM
–
SILENT
e
qw r t
0
EON
MODE START
L AUDIO R
OPTICAL
PHONO
REC OUT
8 9
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
i
EON
MAN'L/AUTO FM AUTO/MAN'L MONO
EDIT
yu
+
–
PTY SEEK
MODE
START
o pas dfg
1 STANDBY/ON
6 VOLUME
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Controls the output level of all audio channels.
This does not affect the REC OUT level.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
+
VIDEO AUX
h
j
7 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons).
8 SPEAKERS A/B
Receives signals from the remote control.
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel.
3 Front panel display
9 BASS EXTENSION ON/OFF
Shows information about the operational status of this
unit (see page 9).
When pushed in (ON), this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if “1B MAIN
SP” on the SET MENU is set to SMALL and “1E LFE/
BASS OUT” is set to SWFR.
4 INPUT MODE
Selects the mode of input for sources that send two or
more types of signals to this unit (see page 26).
You cannot control the input mode when you select 6CH
INPUT as the input source.
0 PROCESSOR DIRECT ON/OFF
5 INPUT l / h
Selects the input source (DVD, D-TV/LD, CBL/SAT,
VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,
CD-R, MD/TAPE) you want to listen to or watch.
When pushed in (ON), BASS, TREBLE, and BASS
EXTENSION are bypassed, eliminating any alteration of
the original signal.
4
0102V1000RDS_1-10_EN
4
9/5/0, 4:41 PM
CONTROLS AND FUNCTIONS
q REC OUT
w EFFECT
s RDS MODE/FREQ
When an RDS station is received, press this button to
change the display mode among the PS mode, PTY mode,
RT mode, CT mode (if the station offers those RDS data
services) and/or frequency display mode in turn.
d EON
Press this button to select the desired program type
(NEWS, INFO, AFFAIRS, SPORT) when you want to
tune in to a radio program of that type automatically.
e A/B/C/D/E
g PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
Selects one of the 5 preset station groups (A to E).
r PROGRAM l / h
Selects the DSP program (see page 28).
t PRESET/TUNING l / h
y PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the PRE OUT jacks or to the speakers.
j TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
• If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the
center, rear and rear center speakers may not match that of the
left and right main speakers.
i PRESET/TUNING (EDIT)
■ Opening and closing the front
panel door
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset station
number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
When you are not operating the controls behind the front
panel door, close the door.
o FM/AM
Switches the reception band between FM and AM.
ADDITIONAL
INFORMATION
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source. To direct this source to the VCR 1 output jacks,
select V-AUX by using REC OUT.
ADVANCED
OPERATION
u VIDEO AUX jacks
h BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
BASIC
OPERAIONT
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
f PTY SEEK MODE
Press this button to set the unit in the PTY SEEK mode.
PREPARATION
Switches the effect speakers (center, rear and rear center
(see page 17)) on and off. If you turn off the output of
these speakers by using EFFECT, all Dolby Digital and
DTS audio signals except for the LFE channel are
directed to the left and right main channels.
When Dolby Digital or DTS signals are mixed, the left
and right main channel signal levels may not match.
INTRODUCTION
Selects the source you want to direct to the audio/video
recorder outputs. When set to the SOURCE position, the
input source is directed to all outputs.
D I
G I
T A
L
p MEMORY (MAN’L/AUTO FM)
APPENDIX
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
a TUNING MODE (AUTO/MAN’L MONO)
To open, press gently on the lower part of the panel.
English
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the “AUTO” indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the “AUTO” indicator does not light up.
5
0102V1000RDS_1-10_EN
5
9/5/0, 4:41 PM
CONTROLS AND FUNCTIONS
Remote Control
This section describes the basic operation of this unit with the remote control. See “REMOTE CONTROL FEATURES”
on pages 50 to 63 for full details.
1
A
2
B
3
4
5
MACRO
TRANSMIT RE-NAME
CLEAR
LEARN
MACRO
OFF
e
r
t
y
ON
u
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
i
TITLE
6
ENTER
SOURCE
DISPLAY
7
C
8
SELECT
POWER
– CHAPTER +
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
10KEY DSP
5
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
11
12
0
+10
+100
o
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
D
8
/DTS
SUR.
10
CHP/INDEX
q
l
/
9
0
SOUND
MENU
SEARCH
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
p
–
DISC
w
a
sd
f
g
h
A
B
C
D
E
PARAMETER
ON SCREEN LEVEL
SET MENU
SLEEP
TEST
Programming section
Provides a selection of programming types you can utilize to
conveniently operates your other components.
A and B buttons
See page 50.
Operation section
Provides functions such as play, stop, skip, etc. for operating
your other components.
Others
Functions vary depending on your components that are set up
with the manufacturer code.
Setup section
Sets speaker output levels, SET MENU, DSP parameters, etc.
6
0102V1000RDS_1-10_EN
6
9/5/0, 4:41 PM
j
k
E
CONTROLS AND FUNCTIONS
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
i 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
o MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
PREPARATION
5 Input selector buttons
u MACRO ON/OFF
Turns the macro function on and off.
INTRODUCTION
2 TRANSMIT indicator
y MACRO
Used to program a series of operations for control by a
single button (see page 61).
p VOLUME +/–
Increases or decreases the volume level.
Select the input source.
6 Display window
Shows the selected source component that you are
controlling.
7 SOURCE SELECT k/n
Selects the source component without switching the
input.
Selects the numeric button (10KEY) mode or DSP mode.
9 DSP program group/Numeric buttons
Select DSP programs or numbers according to the
position of 10KEY/DSP. (Press a button repeatedly to
select a DSP program within that group.)
Turns on or off the Dolby Digital Matrix 6.1 or DTS ES
decoder with 10KEY/DSP set to the DSP position.
q A/B/C/D/E
Selects one of the 5 preset station groups.
w PRESET +/–
Selects a preset station number (1 to 8).
Used for changing the input source name in the display
window (see page 62).
r CLEAR
Used for clearing functions acquired when using the learn
and rename features, programmed macros, and set
manufacturer codes (see pages 62 and 63).
Used for setting up the manufacturer code or for
programming the functions of other remote controls (see
pages 57 to 59).
f ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
g SLEEP
Sets the sleep timer.
h TEST
Outputs the test tone.
j PARAMETER/SET MENU
Selects the PARAMETER mode or SET MENU mode.
k Cursor buttons k/n/–/+
Select and adjust DSP program parameters and SET
MENU items according to the position of PARAMETER/
SET MENU.
l RESET
Press this button after you have changed the batteries or
when the remote control stops working properly.
(Pressing RESET does not clear the acquired functions.)
APPENDIX
t LEARN
d LEVEL
Selects the effect speaker channels (center, rear, rear
center (see page 17) and subwoofer) so you can adjust
their output level independently.
ADDITIONAL
INFORMATION
e RE-NAME
s Cover
Slides down to show the setup buttons.
ADVANCED
OPERATION
0 6.1/ES
BASIC
OPERAIONT
8 10KEY/DSP
a EFFECT
Switches the effect speakers (center, rear and rear center
(see page 17)) on and off. If the output of these speakers
is turned off, all Dolby Digital and DTS audio signals
except for the LFE channel are directed to the left and
right main channels.
English
7
0102V1000RDS_1-10_EN
7
9/5/0, 4:41 PM
CONTROLS AND FUNCTIONS
Using the Remote Control
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
–
30°
30°
–
+
–
+
Approximately 6 m (20 feet)
+
/
1
2
3
5
6
7
10
11
9
4
8
12
0
+
+
+
–
–
–
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity or temperature such as near a heater,
stove or bath;
– dusty places; or
– in places subject to extremely low temperatures.
8
0102V1000RDS_1-10_EN
8
9/5/0, 4:41 PM
CONTROLS AND FUNCTIONS
Front Panel Display
2 34
VIRTUAL
e r
6
78
PS
PTY
90q
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
t y
u
i op
1 t indicator
Lights up when the built-in DTS decoder is on.
Lights up when using Virtual CINEMA DSP (see
page 29).
3 g and o indicators
4 x indicator
Lights up when you select a DSP program.
5 DSP program indicators
6 PTY HOLD indicator
Lights up while searching for stations in the PTY SEEK
mode.
7 RDS mode indicators
q VOLUME level indicator
Indicates the volume level.
w Input source indicator
Shows the current input source with the arrow-shaped
cursor.
e c indicator
Lights up when the built-in Dolby Digital Matrix 6.1 or
DTS ES decoder is on.
r v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
t SP A/B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
y Headphones indicator
Lights up when headphones are connected.
u Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
i MEMORY indicator
Flashes to show a station can be stored.
Lights up when an RDS station that offers the EON data
service is being received.
p TUNED indicator
Lights up when this unit tunes in to a station.
9 STEREO indicator
a SLEEP indicator
Lights up while the sleep timer is on.
Lights up when the unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.
English
8 EON indicator
o Program type name indicators
The name of the selected program type lights up when the
“EON” indicator lights up.
0 AUTO indicator
Shows that this unit is in the automatic tuning mode.
9
0102V1000RDS_1-10_EN
9
9/5/0, 4:41 PM
APPENDIX
The name(s) of the RDS data offered by the currently
received RDS station light(s) up. Illumination of the red
indicator next to the RDS data name shows that the
corresponding RDS mode is now selected.
a
ADDITIONAL
INFORMATION
The name of the selected DSP program lights up when the
ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or q/DTS SURROUND DSP program is
selected.
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
ADVANCED
OPERATION
Light up according to the type of Dolby signals this unit
is reproducing. “ g ” lights up when the builtin Dolby Digital decoder is on. “ o ” lights up
when the built-in Dolby Pro Logic decoder is on.
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
BASIC
OPERAIONT
2 VIRTUAL indicator
w
PREPARATION
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
5
INTRODUCTION
1
CONTROLS AND FUNCTIONS
Rear Panel
1
2
3
5
4
6
7
8
(Europe model)
DIGITAL OUTPUT
MD/
TAPE
AUDIO
TUNER
R
AUDIO
L
R
IN
(PLAY)
CD-R
OPTICAL
AM
ANT
VIDEO
VIDEO
COMPONENT
DVD
DVD
Y
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
OUT
(REC)
GND
R
IN
(PLAY)
75
FM
ANT
UNBAL. CD-R
OUT
(REC)
GND
Y
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
PHONO
OPTICAL
COAXIAL
VCR 2
/DVR
RS232C
MAIN
+
AC OUTLETS
PRE OUT/MAIN IN
L
R
L
SWITCHED
100W MAX. TOTAL
MAIN
MAIN
OUT
B
CENTER
+
REAR
SUB
CENTER WOOFER
–
IMPEDANCE SELECTOR
MONITOR
OUT
Y
OUT
SET BEFORE POWER ON
CENTER
+
–
–
+
MAIN A OR B: 4 MIN. /SPEAKER
A + B: 8 MIN. /SPEAKER
CENTER
: 6 MIN. /SPEAKER
REAR
: 6 MIN. /SPEAKER
L
PB/
CB
SURROUND
PR/
CR
MONITOR
OUT
CENTER
DIGITAL INPUT
– SPEAKERS –
MAIN
IN
R
CBL
/SAT
+
A
D-TV/LD
IN
VCR 1
DVD
CD
MAINS
MD/TAPE
CD
CD-R
S VIDEO
L
SUB
WOOFER
S VIDEO
REAR (SURROUND)
MAIN A OR B: 8 MIN. /SPEAKER
A + B:16 MIN. /SPEAKER
CENTER
: 8 MIN. /SPEAKER
REAR
: 8 MIN. /SPEAKER
R REAR (SURROUND) L
VIDEO
6CH INPUT
9
0
q
1 DIGITAL INPUT jacks
2 DIGITAL OUTPUT jacks
3 Antenna input terminals
w
8 AC power cord
Connect to a power outlet.
9 RS-232C connector
See page 30 for connection information.
This is a control expansion connector for commercial use.
Consult your dealer for details.
4 Audio component jacks
0 6CH INPUT jacks
See pages 12 and 13 for connection information.
5 Video component jacks
See pages 14 and 15 for connection information.
See pages 13 and 18 for connection information.
q IMPEDANCE SELECTOR switch
See pages 16 and 17 for connection information.
Use this switch to match the amplifier output to your
speaker impedance. Set this unit in the standby mode
before you change the setting of this switch (see page 19).
7 PRE OUT/MAIN IN jacks
w AC OUTLET(S)
See page 18 for connection information.
Use these outlets to supply power to your other A/V
components (see page 19).
6 Speaker terminals
10
0102V1000RDS_1-10_EN
10
9/5/0, 4:41 PM
PREPARATION
SPEAKER SETUP
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main speaker (R)
Subwoofer
Rear speaker (R)
Main
speaker (L)
1.8 m
Center speaker
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
■ Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (approx. 6 feet)
above the floor.
■ Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
• If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
“1A CENTER SP” on the SET MENU is set to NONE (see
page 41 for details).
ADDITIONAL
INFORMATION
■ Use of a subwoofer expands your
sound field
■ Main speakers
ADVANCED
OPERATION
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers.
For precise sound localization, however, it is ideal to use
high-performance models that can reproduce sounds over
the full range for the center speaker and the rear speakers.
Rear speaker (L)
Rear center
speaker
See page 17.
BASIC OPERATION
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
PREPARATION
This unit has been designed to provide the best soundfield quality with a 5-speaker system, using left and right
main speakers, left and right rear speakers and a center
speaker. The 6-speaker system, which adds a rear center
speaker to the 5 speaker configuration, is the latest
advancement in surround sound technology. (See page 17
for using the rear center speaker.) If you use different
brands of speakers (with different tonal qualities) in your
system, the tone of a moving human voice and other types
of sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
INTRODUCTION
Speakers to Be Used
■ Subwoofer
APPENDIX
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
11
0103V1000RDS_11-18_EN
11
9/5/0, 4:41 PM
English
Some types of speakers interfere with a video monitor.
If this problem occurs, move the speakers away from
the monitor. If you cannot avoid installing the center
speaker or subwoofer near the video monitor, use a
magnetically shielded speaker.
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.
• After you have completed all connections, check them again to make sure they are correct.
Connecting Audio Components
■ Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 25 for details).
y
• You can designate the input for each digital jack according to
your component by using “7 I/O ASSIGNMENT” on the SET
MENU (see page 44 for details).
About the dust protection cap
Pull out the cap from the optical jack
before you connect the fiber optic cable.
Do not discard the cap. When you are not
using the optical jack, be sure to put the
cap back in place. This cap protects the
jack from dust.
Note
• The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
■ Connecting a turntable
■ Connecting a CD player
y
• The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.
• When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.
■ Connecting an MD recorder, tape
deck or CD recorder
y
• Only digital signals input from a source such as a CD or DVD
are output from the DIGITAL OUTPUT jacks.
• When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
• You can connect an MD recorder to any digital input jack by
using “7 I/O ASSIGNMENT” on the SET MENU (see
page 44).
Notes
• When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit
may distort the sound from other components.
• When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an inline boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
• The GND terminal does not electrically ground the turntable. It
simply reduces noise in the signal. In some cases, you may
hear less noise if you do not connect to the GND terminal.
12
0103V1000RDS_11-18_EN
12
9/5/0, 4:41 PM
CONNECTIONS
OPTICAL
INPUT
OPTICAL
INPUT
MD recorder or
tape deck
OUTPUT
R
L
L
OUTPUT
R
DIGITAL OUTPUT
MD/
TAPE
AUDIO
TUNER
R
OUT
(REC)
GND
CD
75
FM
ANT
L
CD player
UNBAL. CD-R
OUT
(REC)
VIDEO
VIDEO
COMPONENT
DVD
DVD
Y
D-TV
/LD
PB/
CB
PR/
CR
D-TV/LD
Y
IN
O
VCR 1
DVD
GND
R
S VIDEO
L
CBL
/SAT
IN
(PLAY)
OUTPUT
R
R
MD/TAPE
O
CD-R
L
PREPARATION
OPTICAL
AM
ANT
R
AUDIO
L
IN
(PLAY)
CD-R
OPTICAL
OUTPUT
INPUT
L
O
O
INTRODUCTION
INPUT
OPTICAL
OUTPUT
CD recorder
CD
PB/
CB
OUT
D-TV
/LD
PHONO
C
COAXIAL
OUTPUT
CD
PR/
CR
IN
VCR 2
/DVR
RS232C
CBL
/SAT
MAIN
MONITOR
OUT
Y
OUT
PB /
CB
SURROUND
PR/
CR
MONITOR
OUT
CENTER
(Europe model)
DIGITAL INPUT
GND
OUTPUT
SUB
WOOFER
S VIDEO
VIDEO
6CH INPUT
L
R
SUBWOOFER
OUTPUT
CENTER OUTPUT
R
SURROUND
OUTPUT
L
R
MAIN
OUTPUT
External decoder
See page 18.
ADVANCED
OPERATION
L
BASIC OPERATION
OPTICAL
COAXIAL
Turntable
ADDITIONAL
INFORMATION
indicates signal direction
L
indicates left analog cables
R
indicates right analog cables
O
indicates optical cables
C
indicates coaxial cables
APPENDIX
English
13
0103V1000RDS_11-18_EN
13
9/5/0, 4:41 PM
CONNECTIONS
Connecting Video Components
■ About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (PB/CB, PR/CR) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, CB, CR/Y, PB, PR/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
y
Y
VIDEO jack
(composite)
PB/
CB
PR/
CR
S VIDEO jack
COMPONENT VIDEO jacks
• Each type of video jack works independently. Signals input
through the composite video, S-video and component jacks are
output through the corresponding composite video, S-video, and
component jacks, respectively.
• If you make S-video connections to this unit, it is not necessary
to make composite video connections. If both types of
connections are made, this unit gives priority to the S-video
signal.
• You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using “7 I/O
ASSIGNMENT” on the SET MENU (see page 44 for details).
Notes
• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being
connected.
■ Video monitor with a 21-pin connector
Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.
■ VIDEO AUX jacks (on the front panel)
S VIDEO
VIDEO
L AUDIO R
OPTICAL
These jacks are used to connect any video input source
such as a game console to this unit.
VIDEO AUX
S
V
L
R
O
OPTICAL OUT
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
Game console
S VIDEO OUT
14
0103V1000RDS_11-18_EN
14
9/5/0, 4:41 PM
CONNECTIONS
Note
RF
OUTPUT
OPTICAL
OUTPUT
AUDIO
OUTPUT
OPTICAL
OUTPUT
LD player
COMPONENT
OUTPUT
AUDIO
OUTPUT
TV/digital TV or
LD player
V
S
VIDEO
OUTPUT
AUDIO
TUNER
R
AUDIO
L
R
IN
(PLAY)
CD-R
R
OPTICAL
AM
ANT
OUT
(REC)
GND
75 UNBAL. CD-R
OUT
FM
(REC)
ANT
D-TV
/LD
PB/
CB
(Europe model)
PR/
CR
D-TV/LD
GND
O
CD
PB/
CB
OUT
D-TV
/LD
PHONO
O
OPTICAL
COAXIAL
*1
C
CD
RS232C
MAIN
CBL
/SAT
C
PR/
CR
IN
VCR 2
/DVR
MONITOR
OUT
Y
OUT
PB/
CB
SURROUND
PR/
CR
MONITOR
OUT
CENTER
DIGITAL INPUT
SUB
WOOFER
S VIDEO
VIDEO
6CH INPUT
L
ADVANCED
OPERATION
*1 You can connect the Dolby
Digital RF signal output of
your LD player to the
COAXIAL jack by using
“7 I/O ASSIGNMENT” on
the SET MENU (see
page 44).
Y
IN
VCR 1
DVD
RF
demodulator
Y
CBL
/SAT
IN
(PLAY)
RF
INPUT
DVD
MD/TAPE
CD
CD-R
VIDEO
OUTPUT
VIDEO
VIDEO
COMPONENT
DVD
S VIDEO
L
V
S
BASIC OPERATION
DIGITAL OUTPUT
MD/
TAPE
L
DVD player
S VIDEO
OUTPUT
R
L
COMPONENT
OUTPUT
PREPARATION
S VIDEO
OUTPUT
INTRODUCTION
• If your LD player has a Dolby Digital RF signal output jack,
connect it to this unit through an RF demodulator (separately
purchased).
R
S VIDEO
OUTPUT
AUDIO
OUTPUT
V
L
R
L
R
S
S
Cable TV or
satellite tuner
VIDEO
OUTPUT
VIDEO
INPUT
VCR 1 or
VCR 2/DVR (digital
video recorder)
AUDIO INPUT
APPENDIX
COAXIAL
OUTPUT
S VIDEO
OUTPUT
V
V
S VIDEO
INPUT
VIDEO
OUTPUT
ADDITIONAL
INFORMATION
S
AUDIO OUTPUT
No connection
indicates signal direction
L
indicates left analog cables
R
indicates right analog cables
O
indicates optical cables
C
indicates coaxial cables
V
indicates video cables
S
0103V1000RDS_11-18_EN
indicates S-video cables
15
R
V
V
VIDEO
INPUT
S
S VIDEO
INPUT
English
L
SCART-plug
COMPONENT
Video monitor INPUT
15
9/5/0, 4:41 PM
CONNECTIONS
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
• Use speakers with the specified impedance shown on the rear panel of this unit.
• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage the unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
■ Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
10 mm (3/8”)
1
2
1
Remove approx. 10 mm (3/8”) of insulation
from each of the speaker cables.
2
Twist the exposed wires of the cable together
to prevent short circuits.
■ Connecting to the SPEAKERS terminals
Red: positive (+)
Black: negative (–)
1
2
1
2
Unscrew the knob.
3
Tighten the knob to secure the wire.
Insert one bare wire into the hole in the side
of each terminal.
3
■ MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
■ REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
■ CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
16
0103V1000RDS_11-18_EN
16
9/5/0, 4:41 PM
CONNECTIONS
■ Using the rear center speaker
You can enjoy the Dolby Digital Surround EX software or DTS ES software by adding the rear center speaker to the 5speaker configuration.
Connecting the rear center speaker
1
Connect the PRE OUT REAR CENTER jack on this unit to the input jack on the separately
prepared power amplifier.
2
Connect the rear center speaker to the speaker terminals on this power amplifier.
Setting up this unit for using the rear center speaker
When you use a rear center speaker, “1D REAR CT SP” on the SET MENU must be set to LRG or SML (see page 42).
PREPARATION
Note
• Be sure to correctly connect the + terminal of the speaker to the + terminal on the power amplifier, and the – terminal of the speaker
to the – terminal on the power amplifier.
INTRODUCTION
Rear center speaker placement
Place the rear center speaker in the center between the left and right rear speakers at the same height from the floor as
the rear speakers.
Note
Main speakers A
BASIC OPERATION
• No sound is output from the rear center speaker when “1C REAR L/R SP” on the SET MENU is set to NONE (see page 41 for
details).
Main speakers B
Right
Left
Right
Left
ADVANCED
OPERATION
(Europe model)
MAINS
– SPEAKERS –
+
AC OUTLETS
PRE OUT/MAIN IN
+
R
R
L
L
SWITCHED
100W MAX. TOTAL
A
MAIN
IN
MAIN
MAIN
OUT
CENTER
+
ADDITIONAL
INFORMATION
B
REAR
SUB
CENTER WOOFER
–
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
R
+
–
REAR (SURROUND)
–
+
MAIN A OR B: 4 MIN. /SPEAKER
A + B: 8 MIN. /SPEAKER
CENTER
: 6 MIN. /SPEAKER
: 6 MIN. /SPEAKER
REAR
L
MAIN A OR B: 8 MIN. /SPEAKER
A + B:16 MIN. /SPEAKER
CENTER
: 8 MIN. /SPEAKER
: 8 MIN. /SPEAKER
REAR
R REAR (SURROUND) L
APPENDIX
Power
amplifier
Right
Center speaker
Subwoofer connection
See “SUBWOOFER jack”
on page 18.
Left
Rear speakers
Subwoofer
system
English
Rear center
speaker
17
0103V1000RDS_11-18_EN
17
9/5/0, 4:41 PM
CONNECTIONS
Connecting to an External
Amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the PRE OUT jacks as follows.
Note
• When RCA pin plugs are connected to the PRE OUT jacks for
output to an external amplifier, do not use the corresponding
SPEAKERS terminals.
PRE OUT/MAIN IN
R
L
MAIN
IN
1
MAIN
OUT
2
5
5 SUBWOOFER jack
When using a subwoofer with built-in amplifier,
including the YAMAHA Active Servo Processing
Subwoofer System, connect the input jack of the
subwoofer system to this jack.
Low bass signals distributed from the main, center and/or
rear channels are directed to this jack. (The cut-off
frequency of this jack is 90 Hz.) The LFE (low-frequency
effect) signals generated when Dolby Digital or DTS is
decoded are also directed if they are assigned to this jack.
Notes
• Adjust the volume level of the subwoofer with the control on
the subwoofer. The subwoofer volume cannot be adjusted from
this unit.
• Depending on the settings of “1 SPEAKER SET”, “10A LFE
LEVEL” and “11 DTS LFE LEVEL” on the SET MENU,
some signals may not be output from the SUBWOOFER jack.
REAR
SUB
CENTER WOOFER
CENTER
3
Connecting an External Decoder
1 MAIN jacks
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
• MAIN IN jacks
Line input to this unit’s main channel amplifiers.
• MAIN OUT jack
Main channel line output jacks.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
4
R REAR (SURROUND) L
Note
Notes
• The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.
2 REAR CENTER jack
Rear center channel line output jack.
• When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
• When you select 6CH INPUT as the input source, changing
items 1A to 1F on the SET MENU is not affected.
3 CENTER jack
Center channel line output jack.
4 REAR (SURROUND) jacks
Rear channel line output jacks.
18
0103V1000RDS_11-18_EN
18
9/5/0, 4:41 PM
CONNECTIONS
IMPEDANCE SELECTOR Switch
INTRODUCTION
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.
Switch
position
Speaker
Impedance level
If you use one set of main speakers, the impedance of each
speaker must be 4 Ω or higher.
MAINS
Main
If you use two sets of main speakers, the impedance of
each speaker must be 8 Ω or higher.
Left
AC OUTLETS
SWITCHED
100W MAX. TOTAL
Center
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B: 4 MIN. /SPEAKER
A + B: 8 MIN. /SPEAKER
CENTER
: 6 MIN. /SPEAKER
REAR
: 6 MIN. /SPEAKER
Main
MAIN A OR B: 8 MIN. /SPEAKER
A + B:16 MIN. /SPEAKER
CENTER
: 8 MIN. /SPEAKER
REAR
: 8 MIN. /SPEAKER
Right
The impedance must be 6 Ω or higher.
The impedance of each speaker must be 6 Ω or higher.
If you use one set of main speakers, the impedance of each
speaker must be 8 Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16 Ω or higher.
Center
The impedance must be 8 Ω or higher.
Rear
The impedance of each speaker must be 8 Ω or higher.
ADVANCED
OPERATION
IMPEDANCE SELECTOR
Connecting the Power Supply Cords
■ AC OUTLET(S) (SWITCHED)
MAINS
AC OUTLETS
SWITCHED
100W MAX. TOTAL
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B: 4 MIN. /SPEAKER
A + B: 8 MIN. /SPEAKER
CENTER
: 6 MIN. /SPEAKER
REAR
: 6 MIN. /SPEAKER
APPENDIX
Europe model ............................................... 2 OUTLETS
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). These outlets
will supply power to any connected component whenever
this unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 100 W.
ADDITIONAL
INFORMATION
After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if
you will not use this unit for a long period of time.
(Europe model)
BASIC OPERATION
Rear
PREPARATION
(Europe model)
MAIN A OR B: 8 MIN. /SPEAKER
A + B:16 MIN. /SPEAKER
: 8 MIN. /SPEAKER
: 8 MIN. /SPEAKER
CENTER
REAR
To AC outlet
English
SWITCHED
19
0104V1000RDS_19-23_EN
19
9/5/0, 4:41 PM
ON-SCREEN DISPLAY (OSD)
You can display the operation information for this unit on
a video monitor. If you display the SET MENU and DSP
program parameter settings on a monitor, it is much easier
to see the available options and parameters than it is by
reading this information on the front panel display.
Selecting the OSD Mode
1
When you turn on the power, the video
monitor and front panel display show the
level of the main volume for a few seconds
and then switch to show the current DSP
program.
2
Press ON SCREEN on the remote control
repeatedly to change the display mode.
The OSD mode changes in the following order: full
display, short display, and display off.
y
• If a video source is being reproduced, the OSD is
superimposed over the image.
• The OSD signal is not output to the REC OUT jack, and will
not be recorded with any video signal.
• You can set the OSD to turn on (blue background) or off when
a video source is not being reproduced (or the source
component is turned off) by using “14 DISPLAY SET” on the
SET MENU (see page 47).
PARAMETER
ON SCREEN LEVEL
OSD Modes
SET MENU
SLEEP
TEST
You can change the amount of information the OSD
shows.
Full display
This mode always shows the DSP program parameter
settings on the video monitor (see page 70).
Short display
This mode briefly shows the same contents as the front
panel display at the bottom of the screen and then
disappears.
Display off
This mode briefly shows the “DISPLAY OFF” message
at the bottom of the screen and then disappears.
Afterwards, no changes to operations appear on the
monitor except those of the ON SCREEN button.
P01 CONCERT HALL 1
INIT. DLY
ROOM SIZE
LIVENESS
30ms
1.0
5
P01 CONCERT HALL 1
Full display
Short display
y
• When you choose the full display mode, INPUT l / h,
VOLUME and some other types of operation information are
displayed at the bottom of the screen in the same format as that
for the front panel display.
• The SET MENU and test tone display appear regardless of the
OSD mode.
Notes
• If you choose a video input source that has a component
connected to both the S VIDEO IN and composite VIDEO IN
jacks, and both the S VIDEO OUT and composite VIDEO
OUT jacks are connected to a video monitor, the video signal is
output to both the S VIDEO OUT and VIDEO OUT jacks.
However, the OSD is carried only on the S-video signal. If no
video signal is input, the OSD is carried on both the S-video
and composite video signals.
• If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown. Make sure to
connect your video monitor to the COMPONENT VIDEO
jacks and either VIDEO or S VIDEO jacks if you want to see
the OSD.
• Playing back video software that has an anti-copy signal or
video signals with a lot of noise may produce unstable images.
20
0104V1000RDS_19-23_EN
20
9/5/0, 4:41 PM
SPEAKER MODE SETTINGS
Summary of SPEAKER SET Items 1A through 1F
Description
Initial setting
1A CENTER SP
Selects the center channel output mode according to the size of the center speaker.
The possible settings are LRG (large), SML (small) and NONE.
LRG
1B MAIN SP
Selects the main channel output mode according to the size of the main speakers.
The possible settings are LARGE and SMALL.
LARGE
1C REAR L/R SP
Selects the rear channel output mode according to the size of the rear speakers.
The possible settings are LRG (large), SML (small) and NONE.
1D REAR CT SP
Selects the rear center channel output mode according to the size of the rear
center speaker.
The possible settings are LRG (large), SML (small) and NONE.
NONE
1E LFE/BASS OUT
Selects a speaker for the LFE signal output and low bass signal.
The possible settings are SWFR (subwoofer), MAIN, and BOTH.
BOTH
1F MAIN LEVEL
Selects the output level for the main channel signal.
The possible settings are Normal and –10 dB.
Normal
PREPARATION
Item
INTRODUCTION
This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your
configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings
as well as other possible settings. If the initial settings are not appropriate for your speaker configuration, change the
settings on the SET MENU (see page 39).
LRG
BASIC OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
English
21
0104V1000RDS_19-23_EN
21
9/5/0, 4:41 PM
ADJUSTING THE SPEAKER OUTPUT LEVELS
This section explains how to adjust the speaker output
levels by using the test tone generator. When this
adjustment is made, the output level heard at the listening
position will be the same from each speaker. This is
important for the best performance of the digital sound
field processor, the Dolby Pro Logic decoder, Dolby
Digital decoder and DTS decoder.
1
STANDBY
/ON
Front panel
2
Note
• Since this unit cannot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.
Before You Begin
3
1
INPUT
VOLUME
Press STANDBY/ON to turn on the power.
Turn on the video monitor.
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of the
main speakers, press both A
and B.
Front panel
Set BASS and TREBLE on the front panel to
the center position and set BASS
EXTENSION to OFF.
6CH INPUT
INPUT MODE
BASS
D I G I T A L
TREBLE
D I G I TA L
BASS
PROCESSOR
EXTENSION DIRECT
SURROUND
STANDBY
/ON
SOURCE
DVD
MD/TAPE
D-TV/LD
CD-R
SPEAKERS
A
B
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
PRESET/
TUNING
A/B/C/D/E
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
TUNER
CBL/SAT
VCR 1
EDIT
PHONES
CD
ON
OFF
EFFECT
VCR2
/DVR
V-AUX
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
–
TREBLE
+
–
+
PHONO
–
REC OUT
SILENT
ON
OFF
Set to OFF.
MODE START
L AUDIO R
OPTICAL
PROGRAM
+
–
+
VIDEO AUX
Front panel
4
3
2 3
DISC
PARAMETER
ON SCREEN LEVEL
SET MENU
SLEEP
4
Sit in the listening
position and set
PARAMETER/SET MENU
on the remote control to
PARAMETER.
TEST
22
0104V1000RDS_19-23_EN
22
9/5/0, 4:41 PM
PARAMETER
SET MENU
Remote control
ADJUSTING THE SPEAKER OUTPUT LEVELS
The state of the test tone output is also shown on the
monitor by an image of the audio listening room.
This is convenient for adjusting each speaker level.
Using the Test Tone (TEST DOLBY
SUR.)
TV VOL
–
+
2
3
• If the test tone cannot be heard, turn down the volume, set the
unit in the standby mode and check the speaker connections.
+
MUTE
CH
TV MUTE
VOLUME
EFFECT
–
–
Note
DISC
PARAMETER
ON SCREEN LEVEL
SET MENU
1,5
SLEEP
y
TEST
4
3
Press k / n repeatedly to
select the speaker to be
adjusted.
• You can stop the sequence temporarily by holding down k / n.
1
5
When the adjustment is complete, press
TEST.
The test tone stops and the
TEST
current DSP program appears
on the front panel display and
on the video monitor.
Press TEST to output the test tone.
TEST
2
Adjust the volume so you can hear the test
tone.
The test tone is heard from the left main speaker,
center speaker, right main speaker, right rear speaker,
rear center speaker (see page 17) and left rear
speaker in order. The tone is produced for
2.5 seconds each time.
LEFT
RIGHT
(TEST LEFT) (TEST RIGHT)
+
VOLUME
CENTER
(TEST CENTER)
–
RIGHT SURROUND
(TEST R SUR.)
• The tonal quality of the center speaker can be adjusted by using
“5 CENTER GEQ” on the SET MENU (see page 44).
• You can increase the output levels of the effect speakers
(center, left rear, right rear and rear center) to +10 dB. If the
output level of these speakers is lower than that of the main
speakers even after you have increased the output level of these
speakers up to +10 dB, set “1F MAIN LEVEL” on the SET
MENU to –10 dB (see page 43). This setting decreases the
main speaker output level to about one-third of the normal
level. After you have set “1F MAIN LEVEL” on the SET
MENU to –10 dB, adjust the levels for the center, rear and rear
center speakers again.
APPENDIX
LEFT SURROUND
(TEST L SUR.)
y
ADDITIONAL
INFORMATION
Press –/+ repeatedly to
adjust the output level of
the effect speakers so that
the output level coming
from each speaker is the
same.
While adjusting, the test tone is heard from the
selected speaker.
ADVANCED
OPERATION
4
BASIC OPERATION
y
PREPARATION
TV INPUT
LEFT
• If “1A CENTER SP” on the SET MENU is set to NONE, the
center channel sound is automatically output from the left and
right main speakers.
A/B/C/D/E PRESET
+
TEST DOLBY SUR.
INTRODUCTION
Use the test tone to balance the output levels of the
6 speakers required for a surround sound system. The
adjustment of each speaker output level should be made
at your listening position with the remote control. After
completing the adjustments, use VOLUME +/– at your
listening position to check if the adjustments are
satisfactory.
REAR CENTER
(TEST R CENTER)
English
23
0104V1000RDS_19-23_EN
23
9/5/0, 4:42 PM
BASIC OPERATION
BASIC PLAYBACK
1
3
5
INPUT
VOLUME
3
2
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
DVD
MD/TAPE
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
PRESET/
TUNING
A/B/C/D/E
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
TUNER
CBL/SAT
VCR 1
EDIT
PHONES
CD
ON
OFF
EFFECT
VCR2
/DVR
V-AUX
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
3
–
SILENT
+
–
+
VIDEO AUX
6
2 5
5
MACRO
TRANSMIT RE-NAME
CLEAR
LEARN
MACRO
OFF
SPEAKERS
A
B
Front panel
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
REC OUT
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of
main speakers, press both A
and B.
Press INPUT l / h repeatedly (or press one
of the input selector buttons) to select the
input source.
• The current input source is indicated on the front
panel display with an arrow.
• The current input source name and input mode
appear on the front panel display and on the video
monitor for a few seconds.
ON
PHONO
SYSTEM
1
POWER
STANDBY
V-AUX
TUNER
D-TV/LD
CBL/SAT
PHONO
MD/TAPE
VCR 1
CD-R
VCR 2/DVR
CD
INPUT
3
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
or
DVD
6CH INPUT
TITLE
Front panel
ENTER
Remote control
SOURCE
DISPLAY
SELECT
POWER
MENU
SOUND
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
/
6
10KEY DSP
6.1/ES
VIRTUAL
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
TV INPUT
–
+
Select this:
MUTE
CH
TV MUTE
–
+
5
VOLUME
EFFECT
–
DISC
DVD:
D-TV/LD:
CBL/SAT:
VCR 1:
VCR 2/DVR:
V-AUX:
1
Press STANDBY/ON (or SYSTEM POWER) to
turn on the power. Turn on the video
monitor.
The front panel display and the video monitor show
the level of the main volume for a few seconds and
then switch to show the current DSP program.
PHONO:
CD:
TUNER:
CD-R:
MD/TAPE:
SYSTEM
Remote control
24
0105V1000RDS_24-29_EN
24
CT
VOLUME
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
To reproduce the signal from
this component
DVD player
TV or digital TV/LD player
Cable TV/satellite tuner
Video cassette recorder 1
Video cassette recorder 2/digital
video recorder
Another A/V component (connected to
the VIDEO AUX jacks on the front
panel)
Turntable
CD player
AM/FM tuner
CD recorder
MD recorder/tape deck
or
Front panel
RT
dB
ms
POWER
STANDBY
/ON
PTY
Selected input source
A/B/C/D/E PRESET
+
TV VOL
PS
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
9/5/0, 4:42 PM
BASIC PLAYBACK
6
Use the digital sound field processor.
See page 28.
6CH INPUT
6CH INPUT
10KEY DSP
PROGRAM
or
HALL 1
HALL 2
CHURCH
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
or
5
MONO
MOVIE
8
MOVIE
MOVIE
THEATER 1 THEATER 2
9
Front panel
JAZZ CLUB
Remote control
/DTS
SUR.
10
11
12
0
+10
+100
Remote control
Front panel
■ To mute the sound
5
Start playback (or select a broadcast station)
on the source component.
Refer to the operation instructions for the
component.
VOLUME
+
VOLUME
or
–
Front panel
BASS
Remote control
TREBLE
y
• You can also cancel mute to press any operation buttons such
as VOLUME +/–.
• During muting, “MUTE ON” appears on the front panel
display and on the video monitor.
■ When you have finished using
this unit
Press STANDBY/ON (or STANDBY) to set
this unit in the standby mode.
■ Notes on the digital signal
The digital input jacks of this unit can also handle
96-kHz sampling digital signals. (To utilize this, use a
source that supports 96-kHz sampling digital signals and
set the player for digital output. Refer to the operation
instructions for the player.) Note the following when a
96-kHz sampling digital signal is input to this unit:
1. The following indication will appear on the front panel
display.
–
+
–
ON
+
OFF
Front panel
Note
• If the component connected to the VCR 1 OUT, VCR 2/DVR
OUT, CD-R OUT and MD/TAPE OUT jacks is turned off, the
reproduced sound may be distorted or the volume may be
lowered. In these cases, turn on the component.
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
2. DSP programs cannot be selected. Sound will be
output as normal 2-channel stereo sound from only the
left and right main speakers.
ADDITIONAL
INFORMATION
BASS
PROCESSOR
EXTENSION DIRECT
ADVANCED
OPERATION
Adjust the volume to the desired output
level.
If desired, use BASS, TREBLE and BASS
EXTENSION, etc. These controls are only effective
for sound from the main speakers.
MUTE
BASIC
OPERATION
4
Press MUTE on the
remote control.
To restore the audio output to
the previous volume level,
press MUTE again.
PREPARATION
Notes
• If “6CH INPUT” is shown on the front panel display and on
the video monitor, no other source can be played. To select
another input source with INPUT l / h (or the input selector
buttons), press 6CH INPUT to turn off “6CH INPUT” from the
front panel display and the video monitor.
• If you want to enjoy an audio source connected to the 6CH
INPUT jacks together with a video source, first select the video
source and then press 6CH INPUT.
INTRODUCTION
To select a source connected to the 6CH INPUT
jacks
Press 6CH INPUT until “6CH INPUT” appears on the
front panel display and on the video monitor.
Note
3. Adjustment of the speaker output level described on
page 48 cannot be made.
APPENDIX
• If “1B MAIN SP” on the SET MENU is set to SMALL or “1E
LFE/BASS OUT” is set to BOTH, the sound is also output
from the subwoofer.
English
25
0105V1000RDS_24-29_EN
25
9/5/0, 4:42 PM
BASIC PLAYBACK
■ BGV (background video) function
The BGV function allows you to combine a video image
from a video source with a sound from an audio source.
(For example, you can listen to classical music while you
are watching a video.)
Select a source from the video group and then select a
source from the audio group with the input selector
buttons on the remote control. The BGV function does
not work if you select the sources with INPUT l / h on
the front panel.
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
AUTO:
In this mode, the input signal is
automatically selected in the following
order:
1) Dolby Digital or DTS signal
2) Digital (PCM) signal
3) Analog signal
DTS:
In this mode, only the digital input signal
encoded with DTS is selected even if
another signal is input at the same time.
ANALOG: In this mode, only the analog input signal
is selected even if a digital signal is input
at the same time.
Notes
Remote control
Input Modes and Indications
This unit comes with various input jacks. If your
component is connected to more than one type of input
jack, you can set the priority of the input signal.
• If digital signals are input from both the COAXIAL and
OPTICAL jacks, the digital signal from the COAXIAL jack is
selected.
• When AUTO is selected, this unit automatically determines the
type of signal. If this unit detects a Dolby Digital or DTS
signal, the decoder automatically switches to the appropriate
setting and reproduces 5.1 channel source.
• The sound output may be interrupted for some LD and DVD
players in the following situation: The input mode is set to
AUTO. A search is performed while playing the disc encoded
with Dolby Digital or DTS, and then disc playing is restored.
The sound output is interrupted for a moment because the
digital signal was selected again.
When you turn on the power of this unit, the input mode
is set according to “8 INPUT MODE” on the SET MENU
(see page 45 for details).
Press INPUT MODE (or the input selector
button that you have pressed to select the
input source on the remote control)
repeatedly until the desired input mode is
shown on the front panel display and on the
video monitor.
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
INPUT MODE
or
Front panel
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
Remote control
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
Input mode
26
0105V1000RDS_24-29_EN
26
9/5/0, 4:42 PM
BASIC PLAYBACK
■ Notes on playing a source
encoded with a DTS signal
PREPARATION
• For LD software that does not contain a digital
soundtrack, connect the LD player to the analog jacks
and set the input mode to AUTO or ANALOG.
• If the LD player is transmitting a signal by a nonstandard method, this unit cannot detect the Dolby
Digital or DTS signal. In this case, the decoder
automatically switches to PCM or analog.
• Some A/V components such as LD players output
different audio signals through their analog and digital
jacks. Change the input mode as necessary.
• While you are operating the LD player and playing a
disc encoded with a Dolby Digital signal, if you
switch from the pause or chapter forwarding function
to normal playback, you may hear the PCM or analog
sound an instant before the Dolby Digital signal is
played.
INTRODUCTION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
• If the digital output data of the player has been
processed in any way, you may not be able to perform
DTS decoding even if you make a digital connection
between this unit and the player.
• If you play a source encoded with a DTS signal and
set the input mode to ANALOG, this unit reproduces
the noise of an unprocessed DTS signal. When you
want to play a DTS source, be sure to connect the
source to a digital input jack and set the input mode to
AUTO or DTS.
• If you switch the input mode to ANALOG while
playing a source encoded with a DTS signal, this unit
reproduces no sound.
• If you play a source encoded with a DTS signal and
set the input mode to AUTO, there will be a moment
of noise while the unit recognizes the DTS signal and
turns on the DTS decoder. This is not a malfunction.
You can avoid this by setting the input mode to DTS
beforehand.
• If you continue to play a source encoded with a DTS
signal with the input mode setting left to AUTO, this
unit automatically switches to the “DTS-decoding”
mode to prevent noise from being generated during
subsequent operation. (The “t” indicator lights up
on the front panel display.) The “t” indicator will
flash immediately after playback of a source encoded
with a DTS signal has finished. Only a source encoded
with a DTS signal can be played back while this
indicator is flashing. If you want to play a normal
PCM source soon, set the input mode back to AUTO.
• The “t” indicator will flash when the input mode
is set to AUTO and a search or skip operation is
performed while playing back a source encoded with a
DTS signal. If this status continues for 30 or more
seconds, the unit will automatically switch from the
“DTS-decoding” mode to PCM digital signal input
mode and the “t” indicator will go out.
■ Notes on playing an LD source
APPENDIX
English
27
0105V1000RDS_24-29_EN
27
9/5/0, 4:42 PM
BASIC PLAYBACK
Notes
Selecting a Sound Field Program
You can enhance your listening experience by selecting a
DSP program. For details about each program, see
pages 64 to 67.
INPUT
VOLUME
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
PRESET/
TUNING
A/B/C/D/E
TUNER
CBL/SAT
VCR 1
EFFECT
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
–
REC OUT
SILENT
+
+
–
VIDEO AUX
2
10KEY DSP
1
2
6.1/ES
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
8
MOVIE
MOVIE
THEATER 1 THEATER 2
9
10
11
0
+10
CHP/INDEX
/DTS
SUR.
12
+100
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
■ Dolby Digital Matrix 6.1 or DTS
ES decoder
DISC
1
• Choose a DSP program based on your listening preference, and
not on the name of the program. The acoustics of your listening
room affect the DSP program. Minimize the sound reflections
in your room to maximize the effect created by the program.
• When you select an input source, this unit automatically selects
the last DSP program used with that source.
• When you set this unit in the standby mode, the current source
and DSP program are memorized and are automatically
selected when you turn on the power again.
• If a Dolby Digital or DTS signal is input when the input mode
is set to AUTO, the DSP program automatically switches to the
appropriate decoding program.
• When a monaural source is being played with PRO LOGIC/
Normal or PRO LOGIC/ENHANCED, no sound will be heard
from the main speakers and the rear speakers. Sound can only
be heard from the center speaker. However, if “1A CENTER
SP” on the SET MENU is set to NONE, the center channel
sound is output from the main speakers.
• When a source connected to the 6CH INPUT jacks of this unit
is selected, the digital sound field processor cannot be used.
• When 96-kHz sampling digital signals are input to this unit, the
DSP program cannot be selected. In this case, the sound is
reproduced as normal 2-channel stereo.
If you want to utilize the rear center speaker with a 5.1
channel source, press 6.1/ES. However, note that to
achieve the proper effect with the rear center channel, the
Dolby Digital Surround EX or DTS ES software should
be used (see “12 6.1/ES AUTO” on pages 46 and 67 for
details).
10KEY DSP
Set 10KEY/DSP to DSP on
the remote control.
6.1/ES
Remote control
2
Press one of the DSP program group
buttons (or PROGRAM l / h on the front
panel) repeatedly until the DSP program you
want appears on the front panel display and
on the video monitor.
For example, to select the sub-program “Spectacle,”
press MOVIE THEATER 1 repeatedly.
HALL 1
HALL 2
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
ROCK
CONCERT
PROGRAM
or
5
MONO
MOVIE
CHURCH
JAZZ CLUB
VIRTUAL
DTS MOVIE THEATER 1 2
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
/DTS
SUR.
10
11
12
0
+10
+100
Remote control
Front panel
Program group
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
DTS MOVIE THEATER 1 2
PS PTY RT CT
PTY HOLD EON STEREO AUTO
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
Program name (sub-program)
28
0105V1000RDS_24-29_EN
28
PS PTY RT CT
PTY HOLD EON STEREO AUTO
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
MEMORY TUNED
The “ c ” indicator lights up.
8
MOVIE
MOVIE
THEATER 1 THEATER 2
9
CHP/INDEX
Remote control
9/5/0, 4:42 PM
VOLUME
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
BASIC PLAYBACK
■ Virtual CINEMA DSP and SILENT
CINEMA DSP
Press EFFECT to turn off the sound effect
for normal stereo reproduction.
Press EFFECT again to turn the sound effect back
on.
EFFECT
EFFECT
or
Front panel
Remote control
Notes
BASIC
OPERATION
• If you turn off the sound effect, no sound is output from the
center, rear and rear center speakers.
• If you turn off the sound effect while a Dolby Digital or DTS
signal is being output, the dynamic range of the signal is
automatically compressed and the sounds of the center, rear
and rear center channels are mixed and output from the main
speakers.
• The volume may be greatly reduced when you turn off the
sound effect or if you set “10B D-RANGE” on the SET MENU
to MIN. In this case turn on the sound effect.
PREPARATION
Note
• This unit is not set in the virtual CINEMA DSP mode even if
“1C REAR L/R SP” is set to NONE in the following cases:
– when the 6ch Stereo, DOLBY DIGITAL/Normal or DTS/
Normal program is selected;
– when the sound effect is turned off;
– when 6CH INPUT is selected as the input source;
– when 96-kHz sampling digital signals are input to this unit;
– when the Dolby Digital KARAOKE source is played;
– when using the test tone; or
– when connecting the headphones.
INTRODUCTION
You can experience the virtual CINEMA DSP sound field
by setting “1C REAR L/R SP” on the SET MENU to
NONE. The sound field processing is changed to the
Virtual CINEMA DSP mode according to the selected
DSP program. Virtual CINEMA DSP is performed by
using the main speakers. You can also listen to SILENT
CINEMA DSP by connecting your headphones to the
PHONES jack while the digital sound field processor is
on.
Normal Stereo Reproduction
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
English
29
0105V1000RDS_24-29_EN
29
9/5/0, 4:42 PM
TUNING
Connecting the Antennas
Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal
strength.
Connect each antenna correctly to the designated terminals.
AM loop antenna
(included)
Indoor FM
antenna
(included)
(Europe model)
DIGITAL OUTPUT
MD/
TAPE
CD-R
OPTICAL
TUNER
3
Release the tab to lock the lead wires.
Lightly pull the lead wires to confirm a good
connection.
4
Attach the loop antenna to the antenna
stand.
5
Orient the AM loop antenna so that the best
reception is obtained.
AM
ANT
GND
CD
CD-R
75
UNBAL.
y
FM
ANT
DVD
• The AM loop antenna can be removed from the stand and
attached to a wall, etc.
GND
D-TV
/LD
OPTICAL
COAXIAL
CD
Notes
RS232C
CBL
/SAT
DIGITAL INPUT
Ground (GND terminal)
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven
into moist earth.
■ Connecting the indoor FM
antenna
Connect the included indoor FM antenna to the 75Ω
UNBAL. FM ANT terminal.
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
A properly installed outdoor antenna provides clearer
reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may improve the
quality. Consult the nearest authorized YAMAHA
dealer or service center about the outdoor antennas.
Connecting a coaxial cable to the included
75-ohm/300-ohm antenna adapter (U.K. model
only)
2
1
Note
• Do not connect an outdoor FM antenna and the indoor FM
antenna at the same time.
■ Connecting the AM loop antenna
2
Cover
Open the cover of the
included 75-ohm/300-ohm
antenna adapter.
11 (7/16)
8 (5/16)
6 (1/14)
Unit:
mm (inch)
Cut the external sleeve of
the 75-ohm coaxial cable
and prepare it for
connection.
3
1
Lead wire
4
3
5
Cut the lead wire and
remove it.
4
Antenna stand
1
Press and hold the tab to unlock the
terminal hole.
2
Insert the AM loop antenna lead wires into
the AM ANT and GND terminals.
Clamp
with
pliers.
5
Clamp with
pliers.
Insert the wire
into the slot.
Insert the cable wire into
the slot, and clamp it with
pliers.
30
0106V1000RDS_30-34_EN
30
9/5/0, 4:42 PM
Snap the cover into
place.
TUNING
y
Automatic (or Manual) Tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
1
INPUT
VOLUME
6CH INPUT
INPUT MODE
If the signal from the station you want to select is weak,
you must tune in to it manually.
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
EFFECT
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
3
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
–
REC OUT
SILENT
4
+
–
+
VIDEO AUX
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator goes off from
the front panel display.
TUNING
MODE
2 3
AUTO
Goes off
AUTO/MAN'L MONO
1
INPUT
If the colon (:) appears on the front panel display
next to the band indication, press PRESET/TUNING
(EDIT) to turn it off.
Press FM/AM to select the reception band.
“FM” or “AM” appears on the front panel display.
PRESET
/TUNING
FM/AM
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
EDIT
DTS MOVIE THEATER 1 2
DOLBY DIGITAL
PRO LOGIC ENTERTAINM
or
Turn this indicator off.
3
TUNING
MODE
AUTO
Lights up
AUTO/MAN'L MONO
If the colon (:) appears on the front panel display
next to the band indication, press PRESET/TUNING
(EDIT) to turn it off.
PRESET
/TUNING
Press PRESET/TUNING l / h to tune in to
the desired station manually.
PRESET/
TUNING
Hold down the button to
continue the tuning search.
Note
• Manually tuning in to an FM station will automatically change
the reception mode to monaural to increase the signal quality.
DTS MOVIE THEATER 1 2
DOLBY DIGITAL
PRO LOGIC ENTERTAINM
ADDITIONAL
INFORMATION
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
EDIT
4
Turn this indicator off.
4
ADVANCED
OPERATION
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator lights up on
the front panel display.
BASIC
OPERATION
2
Press INPUT l / h to
select TUNER as the input
source.
PREPARATION
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
INTRODUCTION
• Use the manual tuning method if the tuning search does not
stop at the desired station because the signal is weak.
• When tuned in to a station, the “TUNED” indicator lights up
and the frequency of the received station is shown on the front
panel display. If an RDS station that offers the PS data service
is being received, the station name is shown instead of the
frequency on the front panel display.
APPENDIX
Press PRESET/TUNING l or h once to
begin automatic tuning.
PRESET/
Press h to tune in to a higher
TUNING
frequency, or press l to tune
in to a lower frequency. Press
the same button again if the
tuning search does not stop at
the desired station.
English
31
0106V1000RDS_30-34_EN
31
9/5/0, 4:42 PM
TUNING
Notes
Presetting Stations
■ Automatically presetting stations
(for RDS stations)
You can use the automatic preset tuning feature to store
RDS stations. This function enables the unit to
automatically tune in to RDS stations with strong signals,
and to store up to 40 (8 stations x 5 groups) of those
stations in order. (See pages 35 to 37 for details on RDS
stations.) This feature enables you to easily tune in to any
preset station by selecting the preset station number (see
page 33).
INPUT
VOLUME
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
EFFECT
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
–
REC OUT
SILENT
+
+
–
VIDEO AUX
132
1
Press FM/AM to select the FM band.
FM/AM
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator lights up on the
front panel display.
TUNING
MODE
AUTO
Lights up
AUTO/MAN'L MONO
3
Press and hold MEMORY (MAN’L/AUTO FM)
for more than 3 seconds.
The preset number, the “MEMORY” and “AUTO”
indicators flash. Then, after about 5 seconds,
automatic preset tuning begins from the frequency
currently displayed toward the higher frequencies.
MEMORY
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
MAN'L/AUTO FM
PS
PTY
RT
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• You can manually replace a preset station with another FM or
AM station by simply following the procedure of the section
“Manually presetting stations” on page 33.
• If the number of the received stations does not reach E8,
automatic preset tuning has automatically stopped after
searching all stations.
• Only RDS stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune in to it manually
in the monaural mode, and store it by following the procedure
in “Manually presetting stations” on page 33. (There may be a
case that this unit cannot receive a station which could be
received by using the automatic tuning method. This is because
this unit receives a large amount of PI (Program Identification)
data along with the station.)
Automatic preset tuning options
You can select the preset number from which the unit will
store RDS stations and/or begin tuning toward lower
frequencies. Before automatic preset tuning begins (after
pressing MEMORY in step 3):
1. Press A/B/C/D/E and PRESET/TUNING l / h to
select the preset number under which the first station
will be stored. Automatic preset tuning will stop when
stations have all been stored up to E8.
2. Press PRESET/TUNING (EDIT) to turn off the colon
(:) and then press PRESET/TUNING l to begin
tuning toward lower frequencies.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again by using the presetting
station methods.
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZO
NEWS INFO AFFAIRS SPORT
SLE
PRO LOGIC ENTERTAINMENT MEMORY TUNED
When automatic preset tuning is completed, the
front panel display shows the frequency of the last
preset station.
32
0106V1000RDS_30-34_EN
32
9/5/0, 4:42 PM
TUNING
■ Manually presetting stations
5
You can also store up to 40 stations (8 stations x 5
groups) manually.
VOLUME
6CH INPUT
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
DVD
MD/TAPE
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
EFFECT
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
VIRTUAL
PHONO
–
REC OUT
SILENT
+
–
+
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
VIDEO AUX
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
INTRODUCTION
INPUT
INPUT MODE
D I G I T A L
Press MEMORY (MAN’L/AUTO FM) while the
“MEMORY” indicator is flashing.
The station band and
MEMORY
frequency appear on the front
MAN'L/AUTO FM
panel display with the preset
group and number you have
selected.
Shows the displayed station has been stored as A1.
1
2
2,5
6
Tune in to a station.
See page 31 for tuning instructions.
Press MEMORY (MAN’L/AUTO FM).
The “MEMORY” indicator flashes for about
5 seconds.
Repeat steps 1 to 5 to store other stations.
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
PREPARATION
3 4
MEMORY
MEMORY
Flashes
3
Press A/B/C/D/E repeatedly to select a
preset station group (A to E) while the
“MEMORY” indicator is flashing.
The group letter appears and make sure that the
colon (:) appears on the front panel display next to
the band indication.
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
4
You can tune any desired station simply by selecting the
preset station number under which it was stored.
You can also tune a preset station with the remote
control. Press TUNER to select TUNER as the input
source.
INPUT
DTS MOVIE THEATER 1 2
DOLBY DIGITAL
PRO LOGIC ENTERTAINM
6CH INPUT
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
OFF
EFFECT
VCR2
/DVR
V-AUX
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
–
REC OUT
SILENT
+
–
+
VIDEO AUX
ADDITIONAL
INFORMATION
Press PRESET/TUNING l / h to select a
preset station number (1 to 8) while the
“MEMORY” indicator is flashing.
PRESET/
Press h to select a higher
TUNING
preset station number. Press l
to select a lower preset station
number.
VOLUME
INPUT MODE
D I G I T A L
1 2
1
2
ADVANCED
OPERATION
A/B/C/D/E
Tuning in to a Preset Station
BASIC
OPERATION
MAN'L/AUTO FM
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISC
APPENDIX
English
33
0106V1000RDS_30-34_EN
33
9/5/0, 4:42 PM
TUNING
1
Press A/B/C/D/E to select the preset station
group.
The preset group letter appears on the front panel
display and changes each time you press A/B/C/D/E.
A/B/C/D/E
Exchanging Preset Stations
You can exchange the assignment of two preset stations
with each other. The example below describes the
procedure for exchanging preset station “E1” with “A5”.
A/B/C/D/E
or
INPUT
VOLUME
6CH INPUT
INPUT MODE
TV INPUT
D I G I T A L
Front panel
Remote control
D I G I TA L
SURROUND
STANDBY
/ON
2
Press PRESET/TUNING l / h (or
PRESET +/–) to select a preset station
number (1 to 8).
The preset group and number appear on the front
panel display along with the station band, frequency
and the “TUNED” indicator lights up.
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
OFF
EFFECT
VCR2
/DVR
V-AUX
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
+
–
REC OUT
SILENT
+
–
VIDEO AUX
2,4
PRESET
+
PRESET/
TUNING
or
–
DISC
Front panel
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
1
Tune in to preset station “E1”.
See “Tuning in to a Preset Station” on page 33.
2
Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the “MEMORY” indicator flash on the
front panel display.
CH
Remote control
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
PRESET
/TUNING
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
EDIT
3
PTY
Tune in to preset station “A5” by using the
buttons on the front panel.
“A5” and the “MEMORY” indicator flash on the
front panel display.
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
4
PS
DTS MOVIE THEATER 1 2
PTY HOLD EON
DOLBY DIGITAL
NEWS INFO AFF
PRO LOGIC ENTERTAINMENT MEMORY T
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
NEWS INFO AFFAIRS SPORT
PRO LOGIC ENTERTAINMENT MEMORY TUNED
Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
PRESET
/TUNING
EDIT
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZON
NEWS INFO AFFAIRS SPORT
SLE
PRO LOGIC ENTERTAINMENT MEMORY TUNED
Shows the exchange of stations
has been completed.
34
0106V1000RDS_30-34_EN
34
9/5/0, 4:43 PM
RECEIVING RDS STATIONS
Description of RDS Data
This unit can receive PI, PS, PTY, RT, CT, and EON data
when receiving RDS broadcasting stations.
The name of the RDS station being received is displayed.
■ PTY (Program Type) mode:
■ RT (Radio Text) mode:
■ CT (Clock Time) mode:
RDS MODE
/FREQ
The current time is displayed and updated every minute.
If the data are accidentally cut off, “CT WAIT” may
appear.
PS mode
■ EON (Enhanced Other Networks):
ADDITIONAL
INFORMATION
Information about the program (such as the title of the
song, name of the singer, etc.) on the RDS station being
received is displayed by a maximum of 64 alphanumeric
characters, including the umlaut symbol. If other
characters are used for RT data, they are displayed with
under-bars.
ADVANCED
OPERATION
The program type on the RDS station being received is
displayed. There are 15 program types to classify RDS
stations. You can make this unit search for a station
which is broadcasting a program of the desired type. See
page 36 for details.
Notes
• When an RDS station is being received, do not press RDS
MODE/FREQ until one or more RDS mode indicators light up
on the front panel display. If you press the button before the
indicators light up on the front panel display, the mode cannot
be changed. This is because the unit has not yet received all of
the RDS data on the station.
• RDS data not offered by the station cannot be selected.
• The RDS data service cannot be utilized by this unit if the
received signal is not strong enough. In particular, the RT
mode requires a large amount of data to be received, so it is
possible that the RT mode may not be displayed even if other
RDS modes (PS, PTY, etc.) are displayed.
• RDS data cannot sometimes be received under poor reception
conditions. If so, press TUNING MODE so that the “AUTO”
indicator goes off from the front panel display. Although the
reception mode is changed to monaural by this operation,
when you change the display to RDS mode, RDS data may be
displayed.
• If the signal strength is weakened by external interference
during the reception of an RDS station, the RDS data service
may be cut off suddenly and “...WAIT” will appear on the
front panel display.
BASIC
OPERATION
■ PS (Program Service name)
mode:
The four modes are available in this unit for displaying
RDS data. When an RDS station is being received, PS,
PTY, RT and/or CT mode indicators that correspond to
the RDS data services offered by the station light up on
the front panel display. Press RDS MODE/FREQ
repeatedly to change the display mode among the RDS
data offered by the transmitting station in the order
shown below. Illumination of the red indicator next to the
RDS mode indicator shows that the corresponding RDS
mode is now selected.
PREPARATION
RDS data contains various information such as PI
(Program Identification), PS (Program Service name),
PTY (Program Type), RT (Radio Text), CT (Clock Time),
EON (Enhanced Other Networks), etc. The RDS function
is carried out among the network stations.
Changing the RDS Mode
INTRODUCTION
RDS (Radio Data System) is a data transmission system
by FM stations in many countries. Stations using this
system transmit an inaudible stream of data in addition to
the normal radio signal.
PTY mode
See page 37.
APPENDIX
RT mode
CT mode
English
Frequency
display mode
35
0107V1000RDS_35-38_EN
35
9/5/0, 4:43 PM
RECEIVING RDS STATIONS
■ To cancel this function
PTY SEEK Function
Press PTY SEEK MODE twice.
If you select the desired program type, the unit
automatically searches all preset RDS stations that are
broadcasting a program of the required type.
INPUT
VOLUME
■ Program types in the PTY mode
There are 15 program types to classify RDS stations.
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
EFFECT
VCR2
/DVR
V-AUX
OFF
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
PTY SEEK
BASS
–
REC OUT
SILENT
TREBLE
+
+
–
VIDEO AUX
2
1
EON
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
1 3
Press PTY SEEK MODE to set the unit in the
PTY SEEK mode.
The program type of the station being received or
“NEWS” flashes on the front panel display.
LIGHT M
CLASSICS
OTHER M
News
Current affairs
General information
Sports
Education
Drama
Culture
Science
Light entertainment
Pops
Rock
Middle-of-the-road music (easylistening)
Light classics
Serious classics
Other music
VIRTUAL
PTY SEEK
MODE
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M.O.R. M
START
Flashes
2
Press PRESET/TUNING l / h to select the
desired program type.
The selected program type appears on the front
panel display.
PRESET/
TUNING
3
Press PTY SEEK START to begin searching
all preset RDS stations.
The selected program type flashes and the “PTY
HOLD” indicator lights up on the front panel display
while searching for stations.
Lights up
PTY SEEK
PS
DIGITAL
MODE
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
Z
NEWS INFO AFFAIRS SPORT
S
PRO LOGIC ENTERTAINMENT MEMORY TUNED
START
The selected program
type flashes.
• If a station that is broadcasting a program of the
required type is found, the unit stops at that station
and displays the frequency of the station.
• If the called station is not the desired one, press
PTY SEEK START again. The unit begins
searching for another station that is broadcasting a
program of the same type.
36
0107V1000RDS_35-38_EN
36
9/5/0, 4:43 PM
RECEIVING RDS STATIONS
2
EON Function
EON
Lights up
Note
INPUT
VOLUME
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
DVD
MD/TAPE
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
TUNER
CBL/SAT
VCR 1
OFF
EFFECT
VCR2
/DVR
V-AUX
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
EDIT
PHONES
CD
ON
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
VIRTUAL
DTS
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
2
VOLUME
ZONE 2
SLEEP
dB
ms
• If a preset RDS station of the selected program
type starts broadcasting, the unit will
automatically switch from the program being
currently received to that program. The program
type name indicator flashes.
MODE START
L AUDIO R
OPTICAL
PROGRAM
–
+
–
+
VIDEO AUX
2
PS PTY RT CT
PTY HOLD EON STEREO AUTO
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
MEMORY TUNED
VOLUME
dB
ms
2
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
• When broadcasting of the required program ends,
the previously received station (or another
program on the same station) is recalled.
VIRTUAL
DTS
2
PS PTY RT CT
PTY HOLD EON STEREO AUTO
ZONE 2
INFO AFFAIRS SPORT
SLEEP
MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
■ To cancel this function
ADVANCED
OPERATION
2
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
Flashes
Make sure that the “EON” indicator lights up
on the front panel display.
If the “EON” indicator does not light up, tune in to
another RDS station so that the “EON” indicator
lights up.
PS PTY RT CT
PTY HOLD EON STEREO AUTO
ZONE 2
INFO AFFAIRS SPORT
SLEEP
MEMORY TUNED
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
BASIC
OPERATION
SILENT
VIRTUAL
DTS
VIRTUAL
DTS
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
PHONO
REC OUT
1
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
PREPARATION
• This function can only be used when an RDS station that offers
the EON data service is being received. When such a station is
being received, the “EON” indicator lights up on the front
panel display.
INTRODUCTION
This function uses the EON data service on the RDS
station network. If you simply select the desired program
type (NEWS, INFO, AFFAIRS or SPORT), the unit
automatically searches for all preset RDS stations that are
scheduled to broadcast a program of the required type
and switches from the station being currently received to
the new station when the broadcasts starts.
Press EON repeatedly to select the desired
program type (NEWS, INFO, AFFAIRS or
SPORT).
The selected program type name indicator lights up
on the front panel display.
Press EON repeatedly until no program type name lights
up on the front panel display.
ADDITIONAL
INFORMATION
APPENDIX
English
37
0107V1000RDS_35-38_EN
37
9/5/0, 4:43 PM
BASIC RECORDING
REC OUT allows you to record one source while
watching and/or listening to another source.
Notes
Recording adjustments and other operations are
performed from the recording components. Refer to the
operation instructions for these components.
INPUT
VOLUME
6CH INPUT
INPUT MODE
D I G I T A L
D I G I TA L
SURROUND
STANDBY
/ON
SOURCE
DVD
MD/TAPE
D-TV/LD
CD-R
SPEAKERS
A
B
BASS
PROCESSOR
EXTENSION DIRECT
A/B/C/D/E
PRESET/
TUNING
PRESET
TUNING RDS MODE
/TUNING FM/AM MEMORY MODE
/FREQ
TUNER
CBL/SAT
VCR 1
EDIT
PHONES
CD
ON
OFF
EFFECT
VCR2
/DVR
V-AUX
MAN'L/AUTO FM AUTO/MAN'L MONO
S VIDEO
VIDEO
EON
PTY SEEK
BASS
TREBLE
MODE START
L AUDIO R
OPTICAL
PROGRAM
PHONO
–
REC OUT
SILENT
+
–
+
VIDEO AUX
2
1
Turn on the power to the unit and all
connected components.
2
Select the source component you want to
record from by using REC OUT.
• To record the current input source, set REC OUT
to SOURCE.
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
TUNER
CBL/SAT
VCR 1
CD
VCR2
/DVR
V-AUX
• Do a test recording before you start an actual recording.
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of BASS, TREBLE, BASS EXTENSION,
VOLUME, “3 L/R BALANCE” on the SET MENU and DSP
programs does not affect the recorded material.
• A source connected to the 6CH INPUT jacks of this unit cannot
be recorded.
• S-video and composite video signals pass independently
through this unit’s video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S-video (or only a composite
video) signal, you can record only an S-video (or only a
composite video) signal by your VCR.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material
may infringe copyright laws.
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
■ Special considerations when
recording DTS software
PHONO
REC OUT
• To record a source that you do not want to
simultaneously watch or listen to, set REC OUT to
the source you want to record.
SOURCE
MD/TAPE
DVD
D-TV/LD
CD-R
TUNER
CBL/SAT
VCR 1
CD
VCR2
/DVR
V-AUX
PHONO
REC OUT
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
If you want to listen to another source, and REC
OUT is not set to SOURCE, select the source you
want to reproduce with INPUT l / h and adjust the
volume.
y
• Setting REC OUT to SOURCE and using the BGV function
(see page 26) allows the recording of audio and video from a
different source.
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For LDs, DVDs and CDs encoded with DTS
Only 2-channel analog audio signals may be recorded as
follows:
• LDs
Set your LD player’s left and right outputs to the
analog soundtrack.
• DVDs
Use the disc menu to set the DVD player’s mixed 2channel left and right audio outputs to the PCM or
Dolby Digital soundtrack.
• CDs
The DTS signal recorded on CDs can only be output
as a digital bitstream, and therefore cannot be
recorded.
38
0107V1000RDS_35-38_EN
38
9/5/0, 4:43 PM
ADVANCED OPERATION
SET MENU
INTRODUCTION
The SET MENU consists of 15 items including the
speaker mode setting, center graphic equalizer and
parameter initialization features. Choose the appropriate
item and adjust or select the values as necessary.
Adjusting the Items on the SET
MENU
Adjustment should be made with the remote control.
y
10KEY DSP
5
6.1/ES
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
8
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
PREPARATION
• You can adjust the items on the SET MENU while playing a
source.
• We recommend that you adjust the items on the SET MENU
while using a video monitor. It is easier to see the video monitor
than it is to see the front panel display on this unit while
adjusting the items.
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
Note
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISC
• The indication on the front panel display is the abbreviation of
the OSD.
1
PARAMETER
ON SCREEN LEVEL
2,5
3,4
SPEAKER SET
1
TEST
BASIC OPERATION
1A CENTER SP
SET MENU
SLEEP
1B MAIN SP
1C REAR L/R SP
1D REAR CT SP
1E LFE/BASS OUT
Note
1F MAIN LEVEL
3
L/R BALANCE
4
HP TONE CTRL
5
CENTER GEQ
6
INPUT RENAME
7
I/O ASSIGNMENT
8
INPUT MODE
9
PARAM. INI
1
2
Set PARAMETER/SET
MENU to SET MENU.
PARAMETER
SET MENU
Press k / n repeatedly to select the item (1 to
15) you want to adjust.
SET MENU 1/4
1 SPEAKER SET
2 LOW FRQ TEST
3 L/R BALANCE
4 HP TONE CTRL
/ :Up/Down
–/+ Enter
10 DOLBY D. SET
3
10A LFE LEVEL
10B D-RANGE
12 6.1/ES AUTO
2 LOW FRQ TEST
13 SP DELAY TIME
TEST TONE • • • • • OFF
OUTPUT • • • MAIN L/R
FRQ • • • • • • • • • • 88Hz
14 DISPLAY SET
APPENDIX
11 DTS LFE LEVEL
Press – or + once to enter the setup mode of
the selected item.
The last setting you adjusted appears on the video
monitor or on the front panel display.
ADDITIONAL
INFORMATION
LOW FRQ TEST
ADVANCED
OPERATION
2
• Some items require extra steps to change to the desired setting.
15 MEMORY GUARD
English
39
0108V1000RDS_39-49_EN
39
9/5/0, 4:43 PM
SET MENU
Depending on the item, press k / n to select a sub
item.
1 SPEAKER SET (speaker mode
settings)
2 LOW FRQ TEST
Use this feature to select suitable output modes for your
speaker configuration. You must set the output mode
when you use a subwoofer.
TEST TONE • • • • • OFF
OUTPUT • • • MAIN L/R
FRQ • • • • • • • • • 88Hz
Notes
4
Press –/+ repeatedly to change the setting of
the item.
2 LOW FRQ TEST
■ 1A CENTER SP (center speaker
mode)
TEST TONE • • • • • •ON
OUTPUT • • • MAIN L/R
FRQ • • • • • • • • • 88Hz
5
Press k / n repeatedly until the current DSP
program appears or simply press one of the
DSP program group buttons to exit from the
SET MENU.
10KEY DSP
or
HALL 1
HALL 2
CHURCH JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
9
MOVIE
MOVIE
THEATER 1 THEATER 2
• When 96-kHz sampling digital signals are input to this unit,
level adjustments in items 1B and 1E are possible, but those in
items 1A, 1C, 1D and 1F arenot affected.
• When 6CH INPUT is selected as the input source, level
adjustments in items 1A through 1F are not affected.
/DTS
SUR.
10
11
12
0
+10
+100
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the settings of the SET MENU you
adjusted will return to the factory settings. If so, adjust
the items again.
By adding a center speaker to your speaker configuration,
the unit can provide good dialog localization for many
listeners and superior synchronization of sound and
images. The OSD shows a large, small or no center
speaker depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have a large center speaker. The entire
range of the center channel signal is directed to the center
speaker.
1A CENTER SP
LRG SML NONE
SML
Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center
channel are directed to the speakers selected with “1E
LFE/BASS OUT”.
1A CENTER SP
LRG SML NONE
40
0108V1000RDS_39-49_EN
40
9/5/0, 4:43 PM
SET MENU
1A CENTER SP
LRG SML NONE
The OSD shows large, small or no rear speakers
depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have large left and right rear speakers or
if a rear subwoofer is connected to the rear speakers. The
entire range of the rear channel signal is directed to the
left and right rear speakers.
The OSD shows large or small main speakers depending
on how you set this item.
1C REAR L/R SP
Choices: LARGE, SMALL
Initial setting: LARGE
1B MAIN SP
LRG SML NONE
SML
Select this if you have small left and right rear speakers.
The low-frequency signals (90 Hz and below) of the rear
channel are directed to the speakers selected with “1E
LFE/BASS OUT”.
BASIC OPERATION
LARGE
Select this if you have large main speakers. The entire
range of the left and right main channel signal is directed
to the left and right main speakers.
PREPARATION
■ 1B MAIN SP (main speaker mode)
■ 1C REAR L/R SP (rear speaker
mode)
INTRODUCTION
NONE
Select this if you do not have a center speaker. All of the
center channel signals are directed to the left and right
main speakers.
1C REAR L/R SP
SMALL
SMALL
Select this if you have small main speakers. The lowfrequency signals (90 Hz and below) of the main channel
are directed to the speakers selected with “1E LFE/BASS
OUT”.
LRG SML NONE
NONE
Select this if you do not have rear speakers. In this case,
the rear center speaker mode will automatically be set to
NONE and “1D REAR CT SP” will be skipped.
1C REAR L/R SP
LARGE
SMALL
ADDITIONAL
INFORMATION
1B MAIN SP
ADVANCED
OPERATION
LARGE
LRG SML NONE
Note
y
• This unit is set in the virtual CINEMA DSP mode by selecting
NONE for “1C REAR L/R SP”.
APPENDIX
• When you select MAIN for “1E LFE/BASS OUT”, the lowfrequency signals (90 Hz and below) of the main channel are
directed to the main speakers even if you select SMALL for the
main speaker mode.
English
41
0108V1000RDS_39-49_EN
41
9/5/0, 4:43 PM
SET MENU
■ 1D REAR CT SP (rear center
speaker mode)
■ 1E LFE/BASS OUT (bass out
mode)
By adding a rear center speaker to your speaker
configuration, the unit can provide more realistic front-toback and back-to-front transitions.
LFE signals carry low-frequency effects when this unit
decodes a Dolby Digital or DTS signal. Low-frequency
signals are defined as 90 Hz and below.
Choices: LRG (large), SML (small), NONE
Initial setting: NONE
Choices: SWFR (subwoofer), MAIN, BOTH
Initial setting: BOTH
LRG
Select this if you have a large rear center speaker. The
entire range of the rear center channel signal is directed to
the rear center speaker.
SWFR
Select this if you use a subwoofer. The LFE signals are
directed to the subwoofer.
1E LFE/BASS OUT
1D REAR CT SP
SWFR MAIN BOTH
LRG SML NONE
SML
Select this if you have a small rear center speaker. The
low-frequency signals (90 Hz and below) of the rear
center channel are directed to the speakers selected with
“1E LFE/BASS OUT”.
MAIN
Select this if you do not use a subwoofer. The LFE
signals are directed to the main speakers.
1E LFE/BASS OUT
1D REAR CT SP
SWFR MAIN BOTH
LRG SML NONE
NONE
Select this if you do not have a rear center speaker. All of
the rear center channel signals are directed to the left and
right rear speakers.
BOTH
Select this if you use a subwoofer and you want to mix
the main channel low-frequency signals with the LFE
signals.
1E LFE/BASS OUT
1D REAR CT SP
SWFR MAIN BOTH
LRG SML NONE
Note
• The low-frequency signals (90 Hz and below) from all main,
center, rear and rear center (see page 17) channels are directed
to the LFE channel when you select the small speaker setting in
items 1A, 1B, 1C and 1D.
42
0108V1000RDS_39-49_EN
42
9/5/0, 4:43 PM
SET MENU
■ 1F MAIN LEVEL (main level
mode)
3
Press n to go to “FRQ” and press –/+ to
select the frequency you want to use.
4
Adjust the volume of the subwoofer with the
controls on the subwoofer so it matches that
of the speaker you are comparing it to.
Change this setting if you cannot match the output level
of the center and rear speakers with the main speakers
because of the unusually high-efficiency performance of
the main speakers.
Choices: Normal, –10 dB
Initial setting: Normal
Normal
Select this if you can match the output level of your effect
speakers with that of your main speakers when using the
test tone.
1F MAIN LEVEL
Normal
–10dB
1F MAIN LEVEL
The test tone is produced by the tone generator.
The tone generator produces a narrow-band noise
centered on a specified frequency by the band pass filter.
You can change this center frequency from 35 Hz through
250 Hz in one-sixth octave steps.
You can use the test tone not only for adjusting the
subwoofer level, but also for checking the low-frequency
characteristics of your listening room. Low-frequency
sounds are especially affected by the listener’s position,
speaker placement, subwoofer polarity and other
conditions.
Digital generator
(wide band noise produced)
ADVANCED
OPERATION
Noise
Normal
BASIC OPERATION
–10 dB
Select this if you cannot match the output level of your
effect speakers with that of your main speakers when
using the test tone.
■ About the test tone
PREPARATION
Press n to go to “OUTPUT” and press –/+ to
select the speaker you want to compare with
the subwoofer.
If SWFR is selected, the test tone above 90 Hz will
not be output from the subwoofer. The test tone will
not necessarily be output from the selected speakers.
The output mode of the test tone depends on the
settings of “1 SPEAKER SET” on the SET MENU.
INTRODUCTION
2
–10dB
Freq.
2 LOW FRQ TEST
35 Hz – 250 Hz
ADDITIONAL
INFORMATION
Center freq.
Use this feature to adjust the output level of the
subwoofer so it matches that of the other speakers in your
configuration. Change the setting with the remote control
while sitting in the listening position.
1
Press –/+ to set “TEST TONE” to ON, and
adjust the volume with VOLUME +/– so you
can hear the tone.
Band pass filter
APPENDIX
Notes
• Do not turn up the volume too high.
• If no test tone is heard, turn down the volume, set this unit in
the standby mode and make sure all the necessary connections
are correct.
English
43
0108V1000RDS_39-49_EN
43
9/5/0, 4:43 PM
SET MENU
3 L/R BALANCE (balance of the
left and right main speakers)
Use this feature to adjust the balance of the output level
from the left and right main speakers.
Control range: 10 steps for L/R
Initial setting: 0
Press + to decrease the output level for the
left main speaker. Press – for the right main
speaker.
6 INPUT RENAME
Use this feature to change the name of the input which
appears on the OSD or the front panel display.
1
Press an input selector button (or use INPUT
l / h) to select the input you want to
change the name of.
2
Press –/+ to place the _ (under-bar) under
the space or the character you want to edit.
3
Press k / n to select the character you want
to use and –/+ to move to the next one.
• Press n to change the character in the following
order, or press k to go in the reverse order.
A to Z, a space, 0 to 9, a space, a to z, a space, #,
*, +, and so on.
• Follow the foregoing procedure to rename other
inputs.
4 HP TONE CTRL (headphone
tone control)
Use this feature to adjust the level of the bass and treble
when you use your headphones.
Control range (dB): –6 to +3
Initial setting: 0 dB for both BASS and TRBL (treble)
5 CENTER GEQ (center graphic
equalizer)
Note
• You can use up to 8 characters to rename the inputs.
4
Press + repeatedly to exit from INPUT
RENAME.
7 I/O ASSIGNMENT
Use this feature to adjust the built-in 5-band graphic
equalizer so that the center speaker tonal quality matches
that of the left and right main speakers. You can select the
100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies.
Use this feature to designate the input for the
COMPONENT jacks (A and B) and the DIGITAL
INPUT/OUTPUT jacks (1 to 8) to any sources you
want.
Control range (dB): –6 to +6
Initial setting: 0 dB for 5-band
■ 7A [A] [B] (for the COMPONENT
VIDEO jacks)
1
Press n to select a higher frequency and k
to select a lower frequency.
Initial settings: [A] DVD
[B] D-TV/LD
2
Press –/+ to adjust the level of that
frequency.
■ 7B (1) (2) (for the OPTICAL
OUTPUT jacks)
y
• You can monitor the center speaker sound while adjusting this
item by using the test tone. Press TEST before starting the
foregoing procedure. “TEST DOLBY SUR.” appears on the
video monitor, and the test tone starts alternating among the
speakers. Once you begin this procedure, the test tone remains
at the center speaker and you can hear how the sound changes
as you adjust the various frequency levels. To stop the test tone,
press TEST (see pages 22 and 23).
Initial settings: (1) MD/TAPE
(2) CD-R
■ 7C (3) to (6) (for the OPTICAL
INPUT jacks)
Initial settings: (3) CD
(4) CD-R
(5) DVD
(6) D-TV/LD
■ 7D (7) (8) (for the COAXIAL INPUT
jacks)
Initial settings: (7) CD
(8) CBL/SAT
Note
• You cannot select an item more than once for the same type of
jack.
44
0108V1000RDS_39-49_EN
44
9/5/0, 4:43 PM
SET MENU
8 INPUT MODE (initial input
mode)
Choices: AUTO, LAST
Initial setting: AUTO
LAST
Select this to set this unit to automatically select the last
input mode used for that source.
■ 10A LFE LEVEL
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a
Dolby Digital signal. The LFE signal carries the lowfrequency special effect sound which is only added to
certain scenes.
Control value (dB): –20 to 0
Initial setting: 0 dB for both SPEAKER and
HEADPHONE
Note
• Adjust the LFE level according to the capacity of your
subwoofer or headphones.
BASIC OPERATION
9 PARAM. INI (parameter
initialization)
This setting is effective only when this unit decodes
Dolby Digital signals.
PREPARATION
AUTO
Select this to allow this unit to automatically detect the
type of input signal and select the appropriate input mode.
INTRODUCTION
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn
on this unit (see page 26 for details about the input
mode).
10 DOLBY D. SET (Dolby Digital
set)
■ 10B D-RANGE (dynamic range)
Use this feature to adjust the dynamic range.
Use this feature to initialize the parameters for each DSP
program within a DSP program group. When you
initialize a DSP program group, all of the parameter
values within that group revert to their initial settings.
ADVANCED
OPERATION
Press the DSP program group button on the
remote control for the DSP program you
want to initialize.
All of the DSP programs within the selected program
group are initialized.
Choices: MAX, STD (standard), MIN
Initial setting: MAX for both SP (speaker) and HP
(headphones)
• Select MAX for feature films.
• Select STD for general use.
• Select MIN for listening to sources at an extremely
low volume level.
MAX
y
Notes
Input level
MIN
Output level
STD
Dialog
level
H-LEVEL CUT
0.0
1.0
1.0
Output level
• You cannot initialize the individual DSP programs within a
group separately.
• The parameter values of the DSP programs do not change if
you initialize a program group that does not have the asterisk
mark (*).
• When “15 MEMORY GUARD” is set to ON (see page 47),
you cannot initialize any program groups.
• Once you initialize a DSP program group, you cannot
automatically revert to the previous parameter settings.
Dialog
level
ADDITIONAL
INFORMATION
Output level
• The asterisk mark (*) next to a DSP program group number
indicates that you have changed the parameter values in one or
more DSP programs within that group.
Dialog
level
Input level
APPENDIX
0.0
L-LEVEL BST
Input level
Note
45
0108V1000RDS_39-49_EN
45
9/5/0, 4:43 PM
English
• When you select MIN, the sound output may be faint because
some Dolby Digital signals are not compatible with the
minimum-level dynamic range. In this case, select MAX or
STD.
SET MENU
11 DTS LFE LEVEL
This setting is effective only when this unit decodes DTS
signals.
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a DTS
signal. The LFE signal carries the low-frequency special
effect sound which is only added to certain scenes.
Control range (dB): –10 to +10
Initial setting: 0 dB for both SPEAKER and
HEADPHONE
Note
• Adjust the LFE level according to the capacity of your
subwoofer or headphones.
12 6.1/ES AUTO
Use this feature to switch the auto mode of the Dolby
Digital Matrix 6.1 or DTS ES decoder on or off.
13 SP DELAY TIME
Use this feature to adjust the delay of the center and rear
center channel sounds. This feature works when this unit
decodes a Dolby Digital or DTS signal. Ideally, the center
speaker and rear center speaker should be the same
distance from the listening position as the left and right
main speakers. However, in most home situations, the
center speaker or the rear center speaker is placed in line
with the main speakers or rear speakers. By delaying the
sound from the center speaker and the rear center speaker,
the apparent distance from the center speaker and the rear
center speaker to the listening position can be adjusted to
make it seem the same as the distance between the left
and right main speakers and the left and right rear
speakers to the listening position. Adjusting the delay
time for the center speaker is especially important for
giving depth to the dialog.
Control range (ms): 0 to 5 for the center speaker
0 to 30 for the rear center speaker
Center speaker image
Choices: ON, OFF
Initial setting: ON
C
ON
Select this to allow this unit to automatically turn on the
Dolby Digital Matrix 6.1 or DTS ES decoder when a
signal with the appropriate identification is detected.
L
OFF
Select this if you want to turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder manually by pressing 6.1/
ES on the remote control.
RL
C
R
RC
RR
RC
Rear center speaker image
y
• Increasing the delay by 1 ms simulates moving the speakers
about 30 cm (one foot) farther away from the listening
position.
46
0108V1000RDS_39-49_EN
46
9/5/0, 4:43 PM
SET MENU
14 DISPLAY SET
INTRODUCTION
■ BLUE BACK > AUTO/OFF
You can set the OSD background to blue if the video
source is not being reproduced (or the power of the
source component is off).
■ OSD SHIFT (OSD off-set position)
This setting is used to adjust the vertical position of the
OSD.
PREPARATION
■ DIMMER
You can adjust the brightness of the front panel display.
15 MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other settings on this unit.
BASIC OPERATION
Choices: ON, OFF
Initial setting: OFF
Select ON to protect the following features:
• DSP program parameters
• All SET MENU items
• Center, rear, rear center (see page 17) speakers and
subwoofer levels
• The on-screen display (OSD) mode
ADVANCED
OPERATION
Notes
• When “15 MEMORY GUARD” is set to ON, you cannot use
the test tone.
• When “15 MEMORY GUARD” is set to ON, you cannot select
any other SET MENU items.
ADDITIONAL
INFORMATION
APPENDIX
English
47
0108V1000RDS_39-49_EN
47
9/5/0, 4:43 PM
ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS
You can adjust the output level of each effect speaker
(center, left and right rear, rear center (see page 17) and
subwoofer) while listening to a music source.
3
Adjustment should be made with the remote control.
PARAMETER
2
1
ON SCREEN LEVEL
SET MENU
SLEEP
Press –/+ to adjust the speaker output level.
• The control range for the center, left and right rear
or rear center speakers is from +10 dB to –10 dB.
• The control range for the subwoofer is from 0 dB
to –20 dB.
TEST
y
3
• When PARAMETER/SET MENU is set to SET MENU, you
cannot adjust the output level by using LEVEL. However, each
time you press LEVEL, the current level of each speaker
appears on the front panel display and you can check the
speaker level.
Notes
1
2
Set PARAMETER/SET
MENU to PARAMETER.
PARAMETER
SET MENU
Press LEVEL repeatedly to select the
speaker(s) you want to adjust.
Each time you press LEVEL, the selected speaker
changes and appears on the front panel display and
on the video monitor as follows: center, right rear,
rear center (see page 17), left rear and subwoofer.
LEVEL
• If the speaker output mode is set to NONE, the output level of
that speaker cannot be adjusted.
• When you adjust the output level with LEVEL, the settings you
made with the test tone will be changed.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the output level of the effect speakers
you adjusted will return to the factory settings. If so,
adjust the output level again.
Center speaker output level
Right rear speaker output
level
Rear center speaker output
level
Left rear speaker output
level
Subwoofer output level
y
• Once you press LEVEL, you can also select the speaker(s) to
be adjusted by pressing n. (Pressing k changes the selection in
the reverse order.)
LEVEL
48
0108V1000RDS_39-49_EN
48
9/5/0, 4:43 PM
SLEEP TIMER
3
The “SLEEP” indicator soon lights up on the
front panel display after the sleep timer has
been set.
The display then returns to the previous indication.
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
The sleep timer can only be set with the remote control.
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
INTRODUCTION
Use this feature to automatically set this unit in the
standby mode after the amount of time you have set. The
sleep timer is useful when you are going to sleep while
this unit is playing or recording a source. The sleep timer
also automatically turns off the external components
connected to AC OUTLET(S).
y
Canceling the Sleep Timer
Press SLEEP repeatedly until “SLEEP OFF”
appears on the front panel display.
After a few seconds, “SLEEP OFF” disappears, the
“SLEEP” indicator goes off and the display returns
to the previous indication.
Setting the Sleep Timer
1
SLEEP
Press SLEEP repeatedly to set the amount of
time before this unit automatically turns off.
y
• The sleep timer setting can also be canceled by setting this unit
in the standby mode by using STANDBY on the remote control
(or STANDBY/ON on the front panel) or by disconnecting the
AC power cord from the AC outlet.
PARAMETER
ON SCREEN LEVEL
SET MENU
SLEEP
TEST
BASIC OPERATION
2
Select a source and start playback on the
source component.
PREPARATION
• By connecting a commercially available timer to this unit, you
can also set a wake-up timer. Refer to the operation instructions
for the timer.
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
Each time you press SLEEP, the front panel display
changes as shown below.
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
SP
PCM
AB
PS
PTY
RT
CT
DTS MOVIE THEATER 1 2
PTY HOLD EON STEREO AUTO
DOLBY DIGITAL
ZONE 2
NEWS INFO AFFAIRS SPORT
SLEEP
PRO LOGIC ENTERTAINMENT MEMORY TUNED
VOLUME
dB
ms
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
APPENDIX
English
49
0108V1000RDS_39-49_EN
49
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
The remote control can operate this unit as well as other YAMAHA A/V components. To control the components from
other manufacturers (or some from YAMAHA), you must set up the remote control with the manufacturer codes.
This remote control also has two sophisticated features: Learn and Macro. The Learn feature allows it to acquire
functions from the remote controls of other components in your system (or other household appliances) equipped with
an infrared remote control receiver. The Macro feature allows you to program a series of operations in sequence for
operation by a single button, or to use the factory-set macros to operate other YAMAHA components. These features
make it possible for you to reduce the number of remote control in your entertainment room.
Notes
• For the operating distance of the remote control and notes about batteries, see pages 3 and 8.
• For the name and function of each part and button, see pages 6 and 7.
• If the memory on the remote control becomes full, no further learning is possible, even if there are still some programmable buttons
available (see page 59).
Control Area
■ Control area of this unit
■ Component control area
The control area of this unit is the shaded area shown
below. You can use the functions within this area no
matter which component control area is selected.
The component control area is the shaded area shown
below. Each component has different functions for the
operation buttons in the component control area. The
component which has been chosen by pressing an input
selector button can be controlled and the display window
shows the corresponding name of the input.
MACRO
TRANSMIT RE-NAME
CLEAR
LEARN
MACRO
OFF
ON
SYSTEM
Input
selector
buttons
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SELECT
POWER
MACRO
TRANSMIT RE-NAME
10KEY DSP
6.1/ES
PAUSE
STANDBY
ON
V-AUX
TUNER
MD/TAPE
CD-R
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
PHONO
CD
DVD
6CH INPUT
TITLE
ENTER
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
A/B/C/D/E PRESET
TV INPUT
TV VOL
–
OFF
TITLE
SOURCE
CHP/INDEX
+
MACRO
SYSTEM
– CHAPTER +
STOP
LEARN
POWER
/
10KEY/DSP
(DSP is
selected)
CLEAR
SOUND
MENU
SEARCH
REC
These buttons
switch the
control area
Factory settings:
A for the LD
player and B for
the satellite tuner.
+
MUTE
CH
TV MUTE
–
+
Input selector
buttons and these
buttons also switch
the control area for
each component
SELECT
–
SOUND
POWER
REC
STOP
MENU
PAUSE
PLAY
SEARCH
/
10KEY DSP
POWER
HALL 2
HALL 1
/
1
10KEY/DSP
(10KEY is selected)
ROCK
CONCERT
MONO
MOVIE
9
CHP/INDEX
DISC
+
–
REC
STOP
PAUSE
CHURCH JAZZ CLUB
2
3
6
1
10
0
6.1/ES
+
5
7
CH
TV MUTE
8
3
+
–
12
7
+100
MOVIE
MOVIE
THEATER 1 THEATER 2
10
+
CHP/INDEX
TV INPUT
–
SET MENU
6
9
0
MUTE
JAZZ CLUB
4
TV
SPORTS
8
/DTS
SUR.
11
12
+10
+100
A/B/C/D/E PRESET
VOLUME
EFFECT
TV INPUT
TV
VOL
DISC
PARAMETER
ON SCREEN LEVEL
2
11
+10
MONO
MOVIE
PLAY
4
MOVIE
MOVIE
/DTS
ENTERTHEATER 1 ROCK
THEATER 2
SUR.
CONCERT
STADIUM TAINMENT
A/B/C/D/E PRESET
TV VOL
SOUND
– CHAPTER +
ENTERTV
STADIUM HALL
TAINMENT
SPORTS
1
HALL
2
CHURCH
5
6.1/ES
ENTER
– CHAPTER +
SEARCH
DISPLAY
VOLUME
EFFECT
MENU
DISPLAY
+–
CH
TV MUTE
–
DISC
SLEEP
TEST
Component control area
There are 14 component control areas. You can set up the
manufacturer code and program other remote control functions in
each area (you cannot set up the manufacturer code in the OPTN
area). See pages 57 to 59.
50
0109V1000RDS_50-56_EN
50
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
■ SOURCE SELECT k / n
INTRODUCTION
You can control another component independently from
the input you have selected by pressing an input selector
button.
PREPARATION
Press SOURCE SELECT k / n to choose the
component and set the remote control to be
used for it.
The display window will show one of the following:
(when pressing n) OPTN (option), A, B, PHONO, VAUX, TUNER, MD, CD-R, CD, TV/LD (TV or
digital TV/LD), CBSAT (cable TV/satellite tuner),
VCR 1, VCR 2, DVD.
y
• Pressing k shows the same in the reverse order, but you cannot
select OPTN.
SOURCE
BASIC OPERATION
SELECT
■ OPTN (option) area
OPTN is an extra component control area that can be
programmed with other remote control functions.
Note
ADVANCED
OPERATION
• You cannot set up the manufacturer code in this area. See
page 56 for the programmable area.
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SELECT
POWER
MENU
REC
SOUND
– CHAPTER +
SEARCH
STOP
PAUSE
PLAY
/
ADDITIONAL
INFORMATION
Pressing n always selects OPTN first
APPENDIX
English
51
0109V1000RDS_50-56_EN
51
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
Each Component Control Area
The general operational buttons are shown for each area. Some of them may not function depending on the component
you have.
First, press an input selector button or SOURCE SELECT k / n to select a component you want to control.
y
• The YAMAHA code is factory set for the A, TUNER, MD/TAPE, CD, CD-R and DVD buttons. You must set up the manufacturer
code when operating your component (see page 57).
■ Operating a tuner (TUNER area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SELECT
POWER
POWER
MENU
REC
STOP
PAUSE
PLAY
CHURCH
JAZZ CLUB
/
10KEY DSP
HALL 1
HALL 2
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
5
Preset group A
Preset group B
SOUND
– CHAPTER +
SEARCH
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
Preset group A/B/C/D/E
PRESET +/–
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
Preset number 1 to 8
8
/DTS
SUR.
+
Preset group E
Preset group D
Preset group C
VOLUME
EFFECT
–
–
DISC
■ Operating a CD player (CD area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SEARCH
DISPLAY
SELECT
POWER
POWER
MENU
SOUND
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
/
10KEY DSP
6.1/ES
INDEX
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
11
12
0
+10
+100
A/B/C/D/E PRESET
+
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
PLAY
PAUSE
(YAMAHA: Pause/Stop)
STOP
Numeric buttons 1 to 9
/DTS
SUR.
10
CHP/INDEX
Skip search
Clear
Numeric button +10
Numeric button 0
DISC +/– (disc skip)
–
DISC
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
52
0109V1000RDS_50-56_EN
52
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
■ Operating an MD recorder (MD/TAPE area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
INTRODUCTION
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SEARCH
DISPLAY
SELECT
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
/
10KEY DSP
5
MONO
MOVIE
6.1/ES
9
11
12
0
+10
+100
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
Numeric buttons 1 to 9
8
A/B/C/D/E PRESET
+
PAUSE
STOP
/DTS
SUR.
10
CHP/INDEX
PLAY
+
Numeric button +10
Numeric button 0
VOLUME
EFFECT
–
–
DISC
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
BASIC OPERATION
TV VOL +/–, TV INPUT,
and TV MUTE function if
you have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
MOVIE
MOVIE
THEATER 1 THEATER 2
Skip search
PREPARATION
POWER
POWER
Rec/Pause
SOUND
MENU
■ Operating a CD recorder (CD-R area)
ADVANCED
OPERATION
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
ENTER
ADDITIONAL
INFORMATION
SOURCE
DISPLAY
SEARCH
DISPLAY
SELECT
POWER
POWER
STOP
SOUND
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
/
10KEY DSP
6.1/ES
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
PLAY
PAUSE
Numeric buttons 1 to 9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
Skip search
Clear
Numeric button +10
APPENDIX
INDEX
Numeric button 0
MENU
A/B/C/D/E PRESET
+
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISC
53
0109V1000RDS_50-56_EN
53
9/5/0, 4:43 PM
English
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
REMOTE CONTROL FEATURES
■ Operating an LD player (A area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SEARCH
DISPLAY
SELECT
POWER
POWER
STOP
SOUND
– CHAPTER +
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
SOUND
CHAPTER –/+ (chapter search)
PLAY
PAUSE
/
10KEY DSP
Chapter/Time
Numeric button 0
MENU
SEARCH
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
10
11
12
0
+10
+100
CHP/INDEX
Numeric buttons 1 to 9
/DTS
SUR.
Clear
Numeric button +10
A/B/C/D/E PRESET
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
+
TV INPUT
TV VOL
–
+
+
MUTE
CH
TV MUTE
VOLUME
EFFECT
–
–
DISC
Notes
• The A button is not the input selector and only switches the component area for operating an LD player.
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
■ Operating a DVD player (DVD area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
TITLE
Menu cursor/ENTER
ENTER
MENU
DISPLAY
SEARCH
POWER
SOURCE
DISPLAY
SELECT
POWER
MENU
SOUND
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
/
Return
10KEY DSP
6.1/ES
Title/Index
Numeric button 0
Audio
Skip search
PLAY
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
PAUSE
STOP
Numeric buttons 1 to 9
Clear
Numeric button +10
A/B/C/D/E PRESET
+
TV VOL +/–, TV INPUT,
and TV MUTE function if
you have set up the
manufacturer code for
your TV in the D-TV/LD
or PHONO area.
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
DISC +/– (disc skip)
–
DISC
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
54
0109V1000RDS_50-56_EN
54
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
■ Operating a VCR (VCR 1, VCR 2/DVR and V-AUX areas)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
INTRODUCTION
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
Rewind/Fast forward
SELECT
TV/Video input
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
/
10KEY DSP
ROCK
CONCERT
5
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
PLAY
PAUSE
STOP
Numeric buttons 1 to 9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
PREPARATION
REC
(Press twice
to start
recording)
SOUND
– CHAPTER +
SEARCH
POWER
POWER
MENU
Numeric button 10 or 0
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
+
+
MUTE
CH
TV MUTE
VOLUME
EFFECT
–
–
BASIC OPERATION
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
CH +/– (channel)
DISC
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
ADVANCED
OPERATION
■ Operating a TV/digital TV (D-TV/LD and PHONO areas)
Note
• If you operate an LD player in the D-TV/LD area, set the manufacturer code for your LD player in D-TV/LD area, and the
manufacturer code for your TV in PHONO area.
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
ADDITIONAL
INFORMATION
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
DISPLAY
SELECT
POWER
POWER
MENU
REC
STOP
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
5
6.1/ES
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
Numeric buttons 1 to 9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
You can control your VCR
if you have set up the code for VCR 1.
APPENDIX
PAUSE
/
10KEY DSP
Enter
TV INPUT
SOUND
– CHAPTER +
SEARCH
Numeric button 10 or 0
A/B/C/D/E PRESET
+
TV VOL +/–
TV INPUT
TV VOL
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
CH +/– (channel)
–
English
–
+
DISC
TV MUTE
55
0109V1000RDS_50-56_EN
55
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
■ Operating a cable TV (CBL/SAT area) or satellite tuner (B area)
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
6CH INPUT
TITLE
Menu cursor/Menu select
ENTER
MENU
DISPLAY
SOURCE
DISPLAY
SELECT
SOUND
– CHAPTER +
SEARCH
POWER
POWER
MENU
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
/
10KEY DSP
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
6.1/ES
Enter
MOVIE
MOVIE
THEATER 1 THEATER 2
9
Numeric buttons 1 to 9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
You can control your VCR
if you have set up the code for VCR 1.
Recall
Numeric button 0
A/B/C/D/E PRESET
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
+
VOLUME
EFFECT
–
CH +/– (channel)
–
DISC
Notes
• The B button is not the input selector and only switches the component area for operating a satellite tuner.
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
■ Free area (OPTN area)
TITLE
ENTER
SOURCE
DISPLAY
SELECT
POWER
SOUND
MENU
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
/
10KEY DSP
ROCK
CONCERT
5
6.1/ES
MONO
MOVIE
6
7
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
TV VOL +/–, TV INPUT, and
TV MUTE function if you
have set up the
manufacturer code for
your TV in the D-TV/LD or
PHONO area.
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISC
Note
• When the manufacturer code for your TV is set up in the both D-TV/LD and PHONO areas, priority is given to the signal in the DTV/LD area.
56
0109V1000RDS_50-56_EN
56
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
Setting the Manufacturer Code
3
6CH INPUT
The YAMAHA code is factory set for A, TUNER, CD,
MD/TAPE, CD-R and DVD. There is no factory-set code
for B, PHONO, V-AUX, D-TV/LD, CBL/SAT, VCR 1
and VCR 2/DVR.
1
TITLE
ENTER
SOURCE
DISPLAY
SELECT
Press an input selector button, A or B to
select the source component you want to set
up.
POWER
SEARCH
REC
SOUND
MENU
STOP
– CHAPTER +
PAUSE
PLAY
/
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
4
Press and hold LEARN for about 3 seconds
by using a ballpoint pen or similar object.
“SETUP” and the selected component name appear
alternately in the display window.
Press POWER (or any other button) to check
if you have set up the code correctly.
If the component cannot be
POWER
controlled with the remote
/
control, try setting another
code for the same
manufacturer.
y
• If you continuously want to set up another code for another
component, press ENTER and repeat steps 1, 3 and 4.
5
LEARN
Press LEARN again to exit from the setup
mode.
Notes
Notes
• Press LEARN for at least 3 seconds, otherwise the learning
process is started.
• If you do not press any button within 30 seconds during step 3,
the setup process is canceled. If this happens, start over from
step 2.
ADDITIONAL
INFORMATION
• If you have already programmed a remote control function for
a button, the function by learning or macro programming takes
priority over the setup manufacturer code’s function.
• “ERROR” appears in the display window under the following
circumstances:
– when pressing a button other than the cursor and ENTER;
– when pressing more than one button at once; or
– when MACRO ON/OFF, 10KEY/DSP or PARAMETER/SET
MENU is switched to another position.
ADVANCED
OPERATION
LEARN
BASIC OPERATION
2
STANDBY
V-AUX
PREPARATION
SYSTEM
POWER
INTRODUCTION
You can control other components by setting a
manufacturer code. A code can be set up in each
component control area except for the OPTN area.
Press k / n to select the name of your
component’s manufacturer.
You will find the names of most worldwide audiovideo manufacturers in alphabetical order in the
display window.
APPENDIX
English
57
0110V1000RDS_57-63_EN
57
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
■ Controlling a different
component from the source
component (input) you have
selected
1
Repeat steps 1 and 2 of the procedure in
“Setting the Manufacturer Code”.
2
Press l / h to select a library (component
category).
6CH INPUT
TITLE
Programming a New Remote
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
ENTER
SOURCE
DISPLAY
SELECT
POWER
SEARCH
REC
SOUND
MENU
STOP
– CHAPTER +
PAUSE
PLAY
/
There are 13 libraries to set up a manufacturer code:
L:TV, L:CAB (CABLE), L:DBS, L:SAT, L:VCR,
L:DVD, L:LD, L:CD, L:CDR, L:MD, L:TAP (TAPE),
L:TUN (TUNER) and *L:AMP.
3
Repeat steps 3 and 4 of the procedure in
“Setting the Manufacturer Code”.
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1
Set 10KEY/DSP to 10KEY.
2
Press an input selector button, A or B to
select a source component.
10KEY DSP
SYSTEM
About amplifier libraries (L:AMP)
L:AMP has 4 codes: YPC (factory setting), Zone2,
DSP, and No. “YPC” should be selected to operate this
unit. “Zone2” is for operating YAMAHA DSP
amplifiers with Zone 2 feature. “DSP” is for operating
YAMAHA DSP amplifiers other than this unit. “No” is
to clear this unit control area functions.
3
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
Place this remote control and the other
remote control about 50 to 100 mm (2 to
4 in.) apart on a flat surface so that their
infrared transmitters are aimed at each other.
LEARN
CD-R
CLEAR
STANDBY
MD/TAPE
VCR 2/DVR
TRANSMIT RE-NAME
POWER
TUNER
VCR 1
SYSTEM
V-AUX
CBL/SAT
MACRO
ENTER
D-TV/LD
TITLE
ON
MACRO
OFF
CD
PHONO
DVD
6CH INPUT
about 50 to 100 mm
(2 to 4 in.)
58
0110V1000RDS_57-63_EN
58
9/5/0, 4:43 PM
REMOTE CONTROL FEATURES
4
7
Repeat steps 5 and 6 to program additional
functions.
8
Press LEARN again to exit from the learning
mode.
LEARN
LEARN
Notes
Note
TRANSMIT RE-NAME
SYSTEM
MACRO
CD-R
VCR 2/DVR
ENTER
ON
MACRO
OFF
CD
PHONO
DVD
6CH INPUT
BASIC OPERATION
LEARN
TITLE
VCR 1
MD/TAPE
CLEAR
TUNER
CBL/SAT
STANDBY
LEARN
CD-R
CLEAR
STANDBY
MD/TAPE
VCR 2/DVR
TRANSMIT RE-NAME
POWER
TUNER
VCR 1
SYSTEM
V-AUX
CBL/SAT
MACRO
ENTER
D-TV/LD
TITLE
ADVANCED
OPERATION
Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
V-AUX
6
POWER
Press the button for which you want to
program the new function.
“LEARN” is displayed.
D-TV/LD
5
PREPARATION
• If you do not press any button within 30 seconds during steps 5
and 6, the learning process is canceled. If this happens, start
over from step 4.
• It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
• Even if the batteries in the other remote control have enough
power to transmit signals for operation, they may not have
enough power to transmit signals to this remote control.
• When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
• Direct sunlight interferes with infrared rays.
• “ERROR” appears in the display window in the following
circumstances:
– when pressing more than one button at once; or
– when MACRO ON/OFF is switched to another position.
INTRODUCTION
Press LEARN by using a ballpoint pen or
similar object.
“LEARN” and the selected component name appear
alternately in the display window.
ON
MACRO
OFF
CD
PHONO
DVD
6CH INPUT
ADDITIONAL
INFORMATION
Notes
APPENDIX
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
• When the memory is full, “FULL” appears in the display
window, and this remote control cannot acquire any more
functions. Clear unnecessary programmed functions to allow
this remote control to acquire new functions.
English
59
0110V1000RDS_57-63_EN
59
9/5/0, 4:44 PM
REMOTE CONTROL FEATURES
Using the Macro Feature
The Macro feature makes it possible to perform a series of operations by pressing just one button. For example, when
you want to play a CD, normally you would turn on the components, select the CD input, and press the play button to
start playback. The Macro feature lets you perform all those operations by simply pressing the CD macro button. The
macro buttons (the input selector buttons, A and B buttons, SYSTEM POWER and STANDBY) are factory set with
macro programs. You can also program your own macros (see page 61).
Press one of the macro buttons
CD
Automatically transmits signals of each button sequentially
SYSTEM
POWER
Macro buttons
First
CD
PLAY
(CD area)
Second
Third
PHONO
PHONO
–
V-AUX
V-AUX
TUNER
TUNER
–
(*4)
MD/TAPE
MD/TAPE
CD-R
CD-R
CD
CD
D-TV/LD
D-TV/LD
–
PLAY
(MD/TAPE area) (*3)
PLAY
(CD-R area) (*3)
PLAY
(CD area) (*3)
–
SYSTEM
POWER
CBL/SAT
CBL/SAT
–
VCR 1
VCR 1
PLAY
VCR 2/DVR
VCR 2/DVR
DVD
DVD
(*1)
(VCR 1 area) (*3)
PLAY
(VCR 2/DVR area) (*3)
PLAY
(DVD area) (*3)
–
–
–
–
POWER
SYSTEM
POWER
/
(D-TV/LD area) (*2)
STANDBY
STANDBY
–
–
–
*1 In order to turn on some components (including YAMAHA components) connected to this unit, connect those components to the
AC OUTLET(S) on the rear panel. (Power control may not be synchronized with this unit depending on the component. For details,
please refer to the operation instruction for the connected component.)
*2 If the macro you select includes power control functions, the component may be turned off if it is already on when you press the
macro button. For example, if your TV is on and you press the SYSTEM POWER macro button, the TV is turned off.
*3 Playback can be started with any YAMAHA remote control-compatible MD recorders, CD players, CD recorders, DVD players,
and LD players. When using macros to operate other components, it is either necessary to program the PLAY button on the control
area of that component (see page 58) or to set up a manufacturer code (see page 57).
*4 When TUNER is selected as the input source, this unit receives the last station when this unit was set in the standby mode.
60
0110V1000RDS_57-63_EN
60
9/5/0, 4:44 PM
REMOTE CONTROL FEATURES
■ Operating the macro
2
MACRO
MACRO
CLEAR
LEARN
MACRO
OFF
ON
MACRO ON/OFF
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
SYSTEM
Macro buttons
6CH INPUT
1
2
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
Set MACRO ON/OFF to ON.
Press a macro button.
■ Programming a macro
You can program your own macros and use the Macro
feature to transmit many remote control commands by
pressing a single button.
Notes
• If you want to change the source component, use SOURCE
SELECT k / n or input selector buttons. When you use the
input selector buttons, selecting the input is programmed as a
macro step, whereas SOURCE SELECT k / n only changes
the component.
3
Press the buttons of the functions that you
want to include in the macro operation
sequence in order.
y
• You can set up to 10 steps (10 functions). After you have set 10
steps, “FULL” appears and the remote control automatically
exits from the macro mode.
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
ADVANCED
OPERATION
PHONO
1
6CH INPUT
TITLE
MCR 1: DVD input
ENTER
SOURCE
DISPLAY
SELECT
POWER
SEARCH
REC
SOUND
MENU
STOP
– CHAPTER +
PAUSE
PLAY
2
/
3
MCR 2: DVD a
MCR 3: DVD p
indicate the
number of macro
steps you entered
Press MACRO by using a ballpoint pen or
similar object.
“MCR ?” appears in the display window.
Note
• If you do not press any button within 30 seconds during steps 2
and 3, the macro programming process is canceled. If this
happens, start over from step 1.
Note
APPENDIX
appear alternately so that you
can set up the next step
MACRO
ADDITIONAL
INFORMATION
• The factory-set macro is not cleared when a new macro is
programmed for a button. The factory-set macro can be used
again when the programmed macro is cleared.
• It is not possible to add a new signal (macro step) to the
factory-set macro. Programming a macro changes all macro
contents.
• A macro programming is used to transmit learning or setup (or
YAMAHA preset) button signals of this remote control to a
macro button. If necessary, set up the manufacturer code or
program a function with the remote control for your
component.
• This remote control handles button signals that operate
continuously, such as volume control, as short time interval
codes. Macro programming that include these types of macro
steps are therefore not recommended.
y
BASIC OPERATION
• When you have finished using the Macro feature, set MACRO
ON/OFF to OFF.
• While this unit is carrying out a macro program, the unit does
not receive any other button’s function until the macro
operation has been completed (the TRANSMIT indicator stops
flashing).
• Continue to aim the remote control at the component the macro
is operating until the macro operation has been completed.
• “AGAIN” appears in the display window when a button other
than the macro buttons is pressed.
PREPARATION
Note
Notes
1
POWER
INTRODUCTION
TRANSMIT RE-NAME
Press a macro button for which you want to
program the macro operation.
The button you chose for programming the macro
operation and the selected component name appear
alternately in the display window.
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 2.
English
61
0110V1000RDS_57-63_EN
61
9/5/0, 4:44 PM
REMOTE CONTROL FEATURES
4
Press MACRO again when
the operation sequence
you want to program is
complete.
4
MACRO
Press l / h to move the cursor to the next
position.
6CH INPUT
TITLE
ENTER
Note
SOURCE
DISPLAY
• “ERROR” appears in the display window under the following
circumstances:
– when pressing more than one button at once; or
– when MACRO ON/OFF is switched to another position.
Memory back-up
If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Changing the Source Name in the
Display Window
1
Press an input selector button, A or B to
select the source component you want to
rename.
The selected component name appears in the display
window.
SELECT
POWER
SOUND
MENU
SEARCH
REC
STOP
– CHAPTER +
PAUSE
PLAY
/
y
• If you continuously want to rename another source component,
press ENTER and repeat steps 1, 3 and 4.
5
Press RE-NAME again to exit from the
renaming mode.
RE-NAME
Clearing a Learned Function or
Macro
1
Press an input selector button, A or B to
select the source component for which you
want to clear the function.
The selected component name appears in the display
window.
SYSTEM
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
D-TV/LD
CBL/SAT
VCR 1
PHONO
POWER
STANDBY
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
2
2
Press RE-NAME by using
a ballpoint pen or similar
object.
3
Press k / n to select and enter a character.
Pressing n changes the character in the following
order: A to Z, a to z, 0 to 9, space, - (hyphen).
(Pressing k goes in the reverse order.)
RE-NAME
PHONO
Press LEARN if you want to clear a learned
function, or press MACRO to clear a
programmed macro by using a ballpoint pen
or similar object.
LEARN
6CH INPUT
TITLE
ENTER
SOURCE
DISPLAY
SELECT
POWER
SEARCH
REC
STOP
or
SOUND
MENU
– CHAPTER +
PAUSE
MACRO
PLAY
/
Note
• If you do not press any button within 30 seconds during step 3,
the clearing process is canceled. If this happens, start over from
step 2.
62
0110V1000RDS_57-63_EN
62
9/5/0, 4:44 PM
REMOTE CONTROL FEATURES
3
2
Press k / n to select the clear mode.
The mode is shown in the display window in the
following order:
(L: name of a component) Clears
all learned functions for the
component area. Press the input
selector button, A or B to select
the component.
CLEAR
Clears all learned functions for
this unit control area.
Clears all programmed macros.
• You can clear other learned functions and macros at this time
by holding down CLEAR again and pressing the other buttons
for which those learned functions or macros have been
programmed.
Clears all renamed source
names in the display window.
Clears all programmed functions
including setup manufacturer
codes. This returns to the
factory settings.
Note
• “C:NG” appears in the display window if the operation is
unsuccessful. In this case, try step 3 again.
4
3
ADVANCED
OPERATION
Press LEARN or MACRO again to exit from
the clearing mode.
Once you have cleared a learned function or macro
for a button, the button reverts to the factory setting.
Press and hold CLEAR again for about 3
seconds.
“C:OK” appears in the display window.
LEARN
or
CLEAR
Note
Clearing Learned Functions,
Macros, Renamed Source Names,
and Setup Manufacturer Codes
• “C:NG” appears in the display window if the operation is
unsuccessful. In this case, start over from step 2.
4
Press CLEAR to exit from the clearing mode.
Once you have cleared a learned function or macro
for a button, the button reverts to the factory setting.
CLEAR
CLEAR
Note
Note
63
0110V1000RDS_57-63_EN
63
9/5/0, 4:44 PM
English
• If you do not press any button within 30 seconds during steps 2
and 3, the clearing process is canceled. If this happen, start
over from step 1.
• “ERROR” appears in the display window under the following
circumstances:
– when pressing a button other than the cursor and ENTER;
– when pressing more than one button at once; or
– when MACRO ON/OFF, 10KEY/DSP or PARAMETER/SET
MENU is switched to another position.
APPENDIX
Press CLEAR by using a ballpoint pen or
similar object.
ADDITIONAL
INFORMATION
MACRO
1
BASIC OPERATION
y
PREPARATION
Clears all learned functions.
INTRODUCTION
Press and hold CLEAR by using a ballpoint
pen or similar object, and at the same time
press the button for which you want to clear
the learned function or macro for about
3 seconds.
“C:OK” appears in the display window.
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM
This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to
electronically expand and change the shape of the audio sound field from both audio and video sources, creating a
theater-like experience in your listening room. You can create outstanding audio sound field by selecting a suitable DSP
program (this will, of course, depend on what you are listening to) and making desired adjustments.
The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in
mind that most of these are precise digital recreations of actual acoustic environments.
Note
• Select the DSP program that you feel sounds best regardless of the name and description given for it below.
Hi-Fi DSP Programs
■ For audio sources: Nos. 1 to 7
No.
Program (group)
Sub-program
Features
1
CONCERT HALL 1
—
This is a large fan-shaped concert hall which has approximately 2500 seats.
Almost the whole interior is made of wood. There is relatively little reflection
from the walls, and sound spreads finely and beautifully.
2
CONCERT HALL 2
—
A large round concert hall with a rich surround effect. Pronounced reflections
from all directions emphasize the extension of sounds. The sound field has a great
deal of presence, and your virtual seat is near the center, close to the stage.
3
CHURCH
—
This program recreates the acoustic environment of a big church with a high
dome and columns along each side. The reverberation delay is very long while
the early reflections are smaller than with other sound field programs.
4
JAZZ CLUB
—
This is the sound field at stage front in “The Bottom Line”, a famous New York
jazz club. The floor can seat 300 people to the left and right in a sound field
offering a real and vibrant sound.
5
ROCK CONCERT
—
The ideal program for lively, dynamic rock music. The data for this program was
recorded at LA’s “hottest” rock club. The listener’s virtual seat is at the center-left
of the hall.
6
STADIUM
—
This program gives you the long delays and extraordinarily spacious feel of an
outdoor stadium in Los Angeles that is no less than 300 meters (990 feet) in
diameter.
7
ENTERTAINMENT
Disco
This program recreates the acoustic environment of a lively disco in the heart of a
big city. The sound is dense and highly concentrated. It is also characterized by a
high-energy, “immediate” sound.
6ch Stereo
Using this program increases the listening position range. This is a sound field
suitable for background music at parties.
Note
• If “1A CENTER SP” on the SET MENU is set to NONE, no sound is output from the center speaker.
64
0111V1000RDS_64-68_EN
64
9/5/0, 4:44 PM
SOUND FIELD PROGRAM
CINEMA DSP Programs
No.
Program (group)
Sub-program
Features
ENTERTAINMENT
Game
8
TV SPORTS
—
Although the presence sound field is relatively narrow, the surround sound field
employs the sound environment of a large concert hall. With this program, you
can enjoy watching various TV programs such as news, variety shows, music
programs or sports programs. In a stereo broadcast of a sports game, the
commentator is oriented at the center position, and the shouts and the
atmosphere in the stadium spread on the surround side, while their spread to the
rear is properly restrained.
9
MONO MOVIE
—
This program is provided for reproducing monaural video sources (such as old
movies). The program produces the optimum reverberation to create sound
depth by using only the presence sound field.
This program adds a deep and spatial feeling to video game sounds.
No.
Program
(group)
Input source
Sub-program
10 MOVIE
Spectacle
THEATER 1
70 mm Spectacle
Analog,
PCM, Dolby
Digital in
2-channel
DGTL Spectacle *1
Dolby Digital
Spectacle 6.1 *
DTS Spectacle *1
This program creates the extremely wide sound
field of a 70-mm movie theater. It precisely
reproduces the source sound in detail, making
both the video and the sound field incredibly real.
This is ideal for any kind of video source encoded
with Dolby Surround, Dolby Digital or DTS
(especially large-scale movie productions).
DTS
Spectacle ES *2
Sci-Fi
Analog,
PCM, Dolby
Digital in
2-channel
DGTL Sci-Fi *1
Dolby Digital
Sci-Fi 6.1 *
2
DTS Sci-Fi *1
This program clearly reproduces dialog and sound
effects in the latest sound form of science fiction
films, thus creating a broad and expansive
cinematic space amid the silence. You can enjoy
science fiction films in a virtual-space sound field
that includes Dolby Surround, Dolby Digital and
DTS-encoded software employing the most
advanced techniques.
DTS
ADDITIONAL
INFORMATION
70 mm Sci-Fi
ADVANCED
OPERATION
2
Features
BASIC OPERATION
■ For movie programs: Nos. 10 to 12
PREPARATION
7
INTRODUCTION
■ For audio-video sources: Nos. 7 to 9
2
Sci-Fi ES *
APPENDIX
English
65
0111V1000RDS_64-68_EN
65
9/5/0, 4:44 PM
SOUND FIELD PROGRAM
No.
Program
(group)
Sub-program
Features
Input source
11 MOVIE
Adventure 70 mm Adventure
THEATER 2
DGTL Adventure *1
Analog,
PCM, Dolby
Digital in
2-channel
Dolby Digital
This program is ideal for precisely reproducing
the sound design of the newest 70-mm and
multichannel soundtrack films. The sound field is
made to be similar to that of the newest movie
theaters, so the reverberations of the sound field
itself are restrained as much as possible.
2
Adventure 6.1 *
DTS Adventure *1
DTS
Adventure ES *2
General
70 mm General
Analog,
PCM, Dolby
Digital in
2-channel
DGTL General *1
Dolby Digital
General 6.1 *2
DTS General *1
DTS
This program is for reproducing sounds from
70-mm and multichannel soundtrack films, and is
characterized by a soft and extensive sound field.
The presence sound field is relatively narrow. It
spatially spreads all around and toward the
screen, restraining the echo effect of
conversations without losing clarity. For the
surround sound field, the harmony of music or
chorus sounds beautifully in a wide space at the
rear of the sound field.
General ES *2
66
0111V1000RDS_64-68_EN
66
9/5/0, 4:44 PM
SOUND FIELD PROGRAM
No.
Program
(group)
Sub-program
PRO LOGIC/Normal
Analog, PCM,
Dolby Digital
in 2-channel
DOLBY DIGITAL/
Normal *1
Dolby Digital
DOLBY DIGITAL/
Matrix 6.1 *2
DTS DIGITAL SUR./
Normal *1
Features
The built-in decoder precisely reproduces sounds
and sound effects from sources.
The highly efficient decoding process improves
crosstalk and channel separation, and makes
sound positioning smoother and more precise.
In this program, the digital sound field processor
is not turned on.
DTS
Dolby Digital
DOLBY DIGITAL/
Enhanced 6.1 *2
DTS DIGITAL SUR./
Enhanced *1
This program ideally simulates the multi-surround
speaker systems of the 35-mm film theaters.
Dolby Pro Logic decoding, Dolby Digital
decoding or DTS decoding and digital sound field
processing create precise effects without altering
the original sound orientation.
The surround effects produced by this sound field
wrap around the viewer naturally from the back to
the left and right, and toward the screen.
DTS
BASIC OPERATION
DOLBY DIGITAL/
Enhanced *1
Analog,
PCM, Dolby
Digital in
2-channel
PREPARATION
DTS DIGITAL SUR./
ES *2
Enhanced PRO LOGIC/Enhanced
INTRODUCTION
Normal/
12 q/DTS
SURROUND Matrix
6.1/ES
Input source
DTS DIGITAL SUR./
Enhanced ES *2
y
Notes
• The “ x ” indicator does not light up when selecting the sub-program “Normal” of the q/DTS SURROUND program.
• If “1A CENTER SP” on the SET MENU is set to NONE, no sound is output from the center speaker.
• The effect sound is output from the main speakers when a monaural source is played with CINEMA DSP program groups 7 (Game)
and 8 to 11.
ADDITIONAL
INFORMATION
• If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will be automatically
switched to the Dolby Digital playback sound field or DTS playback sound field.
• If Dolby Digital Surround EX software or DTS ES software is played when “12 6.1/ES AUTO” on the SET MENU is set to ON, the
Dolby Digital Matrix 6.1 or DTS ES decoder will automatically turn on and the corresponding DSP program will be selected.
• 6.1/ES on the remote control can be used to turn the Dolby Digital Matrix 6.1 or DTS ES decoder on or off during Dolby Digital 5.1channel source or DTS 5.1-channel source playback.
ADVANCED
OPERATION
*1 The Dolby Digital Matrix 6.1 or DTS ES decoder is off.
*2 The Dolby Digital Matrix 6.1 or DTS ES decoder is on. The “ c ” indicator lights up on the front panel display.
APPENDIX
English
67
0111V1000RDS_64-68_EN
67
9/5/0, 4:44 PM
SOUND FIELD PROGRAM
MOVIE THEATER Programs
Most movie software has 4-channel (left, center, right and surround) sound information encoded by Dolby Surround
matrix processing and stored on the left and right tracks. These signals are processed by the Dolby Pro Logic decoder.
The MOVIE THEATER programs are designed to recreate the spaciousness and delicate nuances of sound that tend to
be lost in the encoding and decoding processes.
The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without
using matrix processing. This unit’s MOVIE THEATER 70-mm programs provide the same quality of sound and sound
localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality
sound designed for movie theaters into your home. With the unit’s MOVIE THEATER programs, you can recreate a
dynamic sound that gives you the feeling of being at a public theater in your listening room by using Dolby Digital or
DTS technology.
■ Dolby Pro Logic + DSP sound field effect
These programs express an immense sound field and a
large surround effect. They also give depth to the sound
from the main speakers to recreate the realistic sound of
a Dolby Stereo theater.
Presence DSP
sound field
Surround DSP
sound field
■ Dolby Digital/DTS + DSP sound field effect
These programs use YAMAHA’s tri-field DSP
processing on each of the Dolby Digital or DTS signals
for the front, left surround and right surround channels.
This processing enables the this unit to reproduce the
immense sound field and surround expression of a Dolby
Digital- or DTS-equipped movie theater without
sacrificing the clear separation of all channels.
Presence DSP
sound field
Right surround DSP
sound field
Left surround DSP
sound field
■ Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect
These programs provide you with the maximum experience of the spacious surround effects since an extra rear center
DSP sound field created from the rear center channel is added.
68
0111V1000RDS_64-68_EN
68
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound “live”, these reflections
enable us to tell where the player is situated, and the size
and shape of the room in which we are sitting.
In any environment, in addition to the direct sound
coming straight to our ears from the player’s instrument,
there are two distinct types of sound reflections that
combine to make up the sound field:
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of
a concert hall, a dance floor, or virtually any size room at
all. This ability to create sound fields at will is exactly
what YAMAHA has done with the digital sound field
processor.
See “Digital Sound Field Parameter Descriptions” on
pages 71 to 74.
ADDITIONAL
INFORMATION
Direct sound, early reflections and subsequent
reverberation taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
ADDITIONAL
INFORMATION
Reverberations
These are caused by reflections from more than one
surface — walls, ceiling, the back of the room — so
numerous that they merge together to form a continuous
sonic “afterglow”. They are non-directional, and lessen
the clarity of the direct sound.
Each DSP program has a set of parameters that allow you
to change the characteristics of the acoustic environment
to precisely create the effect you want. These parameters
correspond to the many natural acoustic factors that
create the sound field you experience in an actual concert
hall or other listening environment. The size of the room,
for example, affects the length of time between the early
reflections. The “ROOM SIZE” parameter provided in
many of the DSP programs alters the timing between
these reflections, thus changing the shape of the “room”
you are listening. In addition to room size, the shape of
the room and the characteristics of its surfaces have a
significant effect on the final sound. Surfaces that absorb
sound, for example, cause the reflections and
reverberations to die out more quickly, while highly
reflective surfaces allow the reflections to carry on for a
longer period of time. The digital sound field parameters
allow you to control these and many other factors that
contribute to your personal sound field, allowing you to
essentially “redesign” the concert halls, theaters, etc.
provided to create custom-tailored listening environments
that ideally match your mood and music.
BASIC OPERATION
Early reflections
Reflected sounds reach our ears extremely rapidly
(50 ms – 100 ms after the direct sound), after reflecting
from one surface only — for example, from the ceiling or
a wall. These reflections fall into specific patterns as
shown in the diagram on page 71 for any particular
environment, and provide vital information to our ears.
Early reflections actually add clarity to the direct sound.
DSP programs consist of some parameters to determine
the apparent room size, reverberation time, distance from
you to the performer, etc. In each program, these
parameters are set with values precisely calculated by
YAMAHA to create a sound field unique to the program.
It is recommended to use DSP programs without
changing the values of parameters; however, this unit also
allows you to create your own sound fields. Starting with
one of the built-in programs, you can adjust those
parameters.
PREPARATION
■ Elements of a sound field
Sound Field Program Parameters
INTRODUCTION
What is a sound field?
APPENDIX
English
69
0112V1000RDS_69-74_EN
69
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
4
Press k / n to select the
parameter.
5
Press –/+ to change the
parameter value.
Adjustments should be made with the remote control.
y
y
• When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name
on the video monitor.
• We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
10KEY DSP
3
6.1/ES
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
8
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
+
TV INPUT
TV VOL
–
MUTE
CH
TV MUTE
+
VOLUME
EFFECT
–
–
DISC
2
4
5
PARAMETER
1
ON SCREEN LEVEL
SET MENU
SLEEP
TEST
6
Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
1
2
3
PARAMETER
Set PARAMETER/SET
MENU to PARAMETER.
SET MENU
Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
ON SCREEN
HALL 1
HALL 2
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
ROCK
CONCERT
5
MONO
MOVIE
9
CHURCH
MOVIE
MOVIE
THEATER 1 THEATER 2
JAZZ CLUB
8
/DTS
SUR.
10
11
12
0
+10
+100
Program No.
Program name (group)
P05 ROCK CONCERT
Cursor
INIT.DLY
LIVENESS
REV.TIME
REV.DELAY
REV.LEVEL
Select the parameter you want to reset. Then press and
hold – or + until the value temporarily stops at the
factory-set value. The asterisk mark (*) by the parameter
name disappears on the video monitor.
■ To reset all of the parameters to
the factory-set values
Select a DSP program you want to adjust.
10KEY DSP
■ To reset some of the parameters
to the factory-set values
15ms
5
1.6s
100ms
7%
Use “9 PARAM. INI” on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 45).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press k / n.
• You cannot change parameter values when “15 MEMORY
GUARD” on the SET MENU is set to ON. If you want to
change the parameter values, set “15 MEMORY GUARD” to
OFF (see page 47).
Parameters
Example of ROCK CONCERT
70
0112V1000RDS_69-74_EN
70
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
Digital Sound Field Parameter Descriptions
Note
• Not all of the following parameters can be found in every program.
■ INIT.DLY (initial delay)
(P.INIT.DLY — for the presence sound field)
Function:
Time
INT. DLY
Level
Level
First reflection
Early
reflections
Time
INT. DLY
BASIC OPERATION
Level
Sound source
Time
INT. DLY
Sound source
ADDITIONAL
INFORMATION
Reflection surface
Large value = 99 ms
Small value = 1 ms
PREPARATION
This parameter changes the apparent distance from the sound source by adjusting the delay between the
direct sound and the first reflection heard by the listener.
Control range: 1 – 99 msec
Description:
The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther
the apparent distance seems. For a small room, this parameter would be set to a small value, for a large
room, set it to a large value.
INTRODUCTION
You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your
listening room.
■ ROOM SIZE
(P.ROOM SIZE — for the presence sound field)
Function:
ADDITIONAL
INFORMATION
This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the
surround sound field becomes.
Control range: 0.1 – 2.0
Description:
As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between
the original reflected sound and the subsequent reflections. By controlling the time between the
reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from
one to two, doubles the apparent length of the room.
Sound source
Level
Level
Time
APPENDIX
Level
Early reflections
Time
Time
Sound source
English
Small value = 0.1
Large value = 2.0
71
0112V1000RDS_69-74_EN
71
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
■ LIVENESS
Function:
This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the
early reflections decay.
Control range: 0 – 10
Description:
The early reflections of a sound source decay much faster in a room with acoustically absorbent wall
surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces
is referred to as “dead,” while a room with highly reflective surfaces is referred to as “live.” The
“LIVENESS” parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the
room.
Sound source
Time
Level
Dead
Level
Level
Live
Time
Time
Small reflected sound
Large reflected sound
Sound source
Small value = 0
Large value = 10
■ S.DELAY (surround delay)
Function:
This parameter adjusts the delay between the direct sound and the first reflection in the surround sound
field.
Control range: 0 – 49 msec (The range depends on the signal format.)
■ S.INIT.DLY (surround initial delay)
Function:
This parameter adjusts the delay between the direct sound and the first reflection on the surround side
of the sound field. You can only adjust this parameter when at least two front channels and two rear
channels are used.
Control range: 1 – 49 msec
■ S.ROOM SIZE (surround room size)
Function:
This parameter adjusts the apparent size of the surround sound field.
Control range: 0.1 – 2.0
■ S.LIVENESS (surround liveness)
Function:
This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field.
Control range: 0 – 10
72
0112V1000RDS_69-74_EN
72
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
■ RC.INIT.DLY (rear center initial delay)
Function:
INTRODUCTION
This parameter adjusts the delay between the direct sound and the first reflection in the rear center
sound field.
Control range: 1 – 49 msec
■ RC.ROOM SIZE (rear center room size)
Function:
This parameter adjusts the apparent size of the rear center sound field.
Control range: 0.1 – 2.0
■ RC.LIVENESS (rear center liveness)
Function:
This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field.
Control range: 0 – 10
Function:
This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to
decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an
extremely wide range.
Control range: 1.0 – 5.0 sec
Description:
Set a longer reverberation time for “dead” sources and listening room environments and a shorter time
for “live” sources and listening room environments.
REV. TIME
60 dB
Time
REV. TIME
ADDITIONAL
INFORMATION
Short reverberations
60 dB
Time
Time
REV. TIME
Reverberations
Level
60 dB
Level
Level
Reverberations
BASIC OPERATION
Sound source
Early reflections
Reverberations
Long reverberations
Sound source
ADDITIONAL
INFORMATION
Small value = 1.0 s
PREPARATION
■ REV.TIME (reverberation time)
Large value = 5.0 s
APPENDIX
English
73
0112V1000RDS_69-74_EN
73
9/5/0, 4:44 PM
SOUND FIELD PROGRAM PARAMETER EDITING
■ REV.DELAY (reverberation delay)
Function:
This parameter adjusts the time difference between the beginning of the direct sound and the beginning
of the reverberation sound.
Control range: 0 – 250 msec
Description:
The larger the value, the later the reverberation sound begins. A later reverberation sound makes you
feel like you are in a larger acoustic environment.
Level
Sound
source
Reverberation
(dB)
60 dB
Time
REV.
DELAY
REV TIME
■ REV.LEVEL (reverberation level)
Function:
This parameter adjusts the volume of the reverberation sound.
Control range: 0 – 100%
Description:
The larger the value, the stronger the reverberation becomes.
Level
Sound source
REV. LEVEL
Time
■ CT.DELAY (center delay)
■ LS.DELAY (left surround delay)
■ RC.DELAY (rear center delay)
■ RS.DELAY (right surround delay)
Function:
These parameters adjust the sound delay for each channel in 6 channel stereo mode.
Control range: 0 – 50 msec
74
0112V1000RDS_69-74_EN
74
9/5/0, 4:44 PM
APPENDIX
TROUBLESHOOTING
■ General
Problem
Cause
Remedy
Refer to
page
Firmly connect the power cord.
19
The IMPEDANCE SELECTOR switch
on the rear panel is not fully set to the
left or right position.
Set the switch fully to the left or right
position when the unit is in the standby
mode.
19
The protection circuitry has been
activated.
Make sure all speaker wire connections on
this unit and on all speakers are secure and
that the wire for each connection does not
touch anything other than its respective
connection.
16, 17
No sound and/or no
picture.
Incorrect input or output cable connections.
Connect the cables properly. If the problem
persists, the cables may be defective.
12 – 15
An appropriate input source has not
been selected.
Select an appropriate input source with
INPUT l / h or 6CH INPUT (or the input
selector buttons).
24
Secure the connections.
The main speakers to be used have not
been selected properly.
Select the main speakers with SPEAKERS A
and/or B.
24
The volume is turned down.
Turn up the volume.
25
The sound is muted.
Press MUTE or any operation buttons of this
unit to cancel a mute and adjust the volume.
25
Digital signals other than PCM audio,
Dolby Digital or DTS signal which this
unit cannot reproduce are being input to
this unit by playing a CD-ROM, etc.
Play a source whose signals this unit can
reproduce.
—
No picture.
There is no S-video connection between this
unit and the video monitor, although
S-video signals are being input to this unit.
Connect the monitor’s S-video input jack to
this unit’s S VIDEO MONITOR OUT jack.
14, 15
The sound suddenly
goes off.
The protection circuit has been activated
because of a short circuit, etc.
Check the IMPEDANCE SELECTOR
switch is set to the appropriate position and
then turn the unit back on.
19
The sleep timer has functioned.
Turn on the power, and play the source
again.
49
The sound is muted.
Press MUTE or any operation buttons of this
unit to cancel a mute and adjust the volume.
25
Incorrect cable connections.
Connect the cables properly. If the problem
persists, the cables may be defective.
Incorrect setting of “3 L/R BALANCE”
on the SET MENU.
Adjust it to the appropriate position.
12 – 17
44
APPENDIX
Only the speaker on one
side can be heard.
16, 17
ADDITIONAL
INFORMATION
Check the speaker wires are not touching
each other and then turn the unit back on.
16, 17
ADVANCED
OPERATION
The speaker connections are not secure.
BASIC
OPERAIONT
The power cord is not connected or the plug
is not completely inserted.
PREPARATION
The unit fails to turn on
when STANDBY/ON (or
SYSTEM POWER) is
pressed, or enters in the
standby mode soon
after the power has
been turned on.
INTRODUCTION
Refer to the chart below when the unit does not function properly. If the problem you are experiencing is not listed
below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord, and
contact the nearest authorized YAMAHA dealer or service center.
English
75
0113V1000RDS_75-80_EN
75
9/5/0, 4:44 PM
TROUBLESHOOTING
Problem
Cause
No sound from the
effect speakers.
Remedy
The sound effect is off.
Press EFFECT to turn it on.
29
A Dolby Surround, Dolby Digital or
DTS decoding DSP program is being
used with material not encoded with
Dolby Surround, Dolby Digital or DTS.
Select another DSP program.
64 – 67
A 96-kHz sampling digital signal is
being input to this unit.
No sound from the
center speaker.
25
The output level of the center speaker is set
to minimum.
Raise the level of the center speaker.
48
“1A CENTER SP” on the SET MENU
is set to NONE.
Select the appropriate mode for your center
speaker.
41
One of the Hi-Fi DSP programs (1 to 7)
has been selected.
Select another DSP program.
The source encoded with a Dolby
Digital or DTS signal does not have a
center channel signal.
No sound from the rear
speakers.
No sound from the
subwoofer.
64 – 67
—
The output level of the rear speakers is set
to minimum.
Raise the output level of the rear speakers.
A monaural source is being played with
the program 12.
Select another DSP program.
“1E LFE/BASS OUT” on the SET MENU
is set to MAIN when a Dolby Digital or
DTS signal is being played.
Select SWFR or BOTH.
42
“1E LFE/BASS OUT” on the SET
MENU is set to SWFR or MAIN when a
2-channel source is being played.
Select BOTH.
42
The source does not contain low bass
signals (90 Hz and below).
Poor bass reproduction.
Refer to
page
48
64 – 67
—
“1E LFE/BASS OUT” on the SET MENU
is set to SWFR or BOTH and your system
does not include a subwoofer.
Select MAIN.
The output mode for each speaker (main,
center or rear) on the SET MENU does not
match your speaker configuration.
Select the appropriate output mode for each
speaker based on the size of the speakers in
your configuration.
No sound from the rear
center speaker.
“1D REAR CT SP” on the SET MENU is
set to NONE.
Select LRG or SML.
A “humming” sound can
be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the
problem persists, the cables may be
defective.
12 – 15
No connection from the turntable to the
GND terminal.
Connect the grounding cord of your
turntable to the GND terminal of this unit.
12, 13
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to the unit
through an MC-head amplifier.
The volume level is low
while playing a record.
76
0113V1000RDS_75-80_EN
76
9/5/0, 4:44 PM
42
40 – 42
42
12
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
The volume level cannot
be increased, or the
sound is distorted.
The component connected to the REC OUT
jacks of this unit is turned off.
The sound effect cannot
be recorded.
It is not possible to record the sound effect
by a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack of
this unit.
A source component is only connected to
the analog input jacks of this unit.
Connect the source component to the digital
input jacks of this unit.
The sound field
parameters and some
other settings on this
unit cannot be changed.
“15 MEMORY GUARD” on the SET MENU
is set to ON.
Select OFF.
47
This unit does not
operate properly.
The internal microcomputer has been frozen
by an external electric shock (such as
lightning or excessive static electricity) or
by a power supply with low voltage.
Disconnect the AC power cord from the
outlet and then plug it in again after about
30 seconds.
—
“CHECK SP WIRES”
appears on the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected
correctly.
16, 17
The sound is degraded
when listening with
headphones connected
to a tape deck or CD
player that is connected
to this unit.
This unit is in the standby mode.
Turn on the power of the unit.
—
There is noise
interference from digital
or high-frequency
equipment, or the unit.
The unit is too close to the digital or highfrequency equipment.
Move the unit further away from such
equipment.
—
Turn on the power to the component.
12
12 – 15
INTRODUCTION
38
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
English
77
0113V1000RDS_75-80_EN
77
9/5/0, 4:44 PM
TROUBLESHOOTING
■ Tuner
Cause
FM stereo reception
is noisy.
The characteristics of FM stereo broadcasts
may cause this problem when the
transmitter is too far away or the antenna
input is poor.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
Use the manual tuning method.
30, 31
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
30
The desired station
cannot be tuned in
with the automatic
tuning method.
The station is too weak.
Use the manual tuning method.
Use a high-quality directional FM antenna.
Previously preset
stations can no
longer be tuned in.
The unit has been disconnected for a long
period.
Re-store the stations.
The desired station
cannot be tuned in
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for best reception.
Use the manual tuning method.
Noises result from lightning, fluorescent
lamps, motors, thermostats and other
electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
30
A TV set is being used nearby.
Move this unit away from the TV.
—
There is distortion,
and clear reception
cannot be obtained
even with a good FM
FM antenna.
There are continuous
AM crackling and hissing
noises.
There are buzzing
and whining noises
(especially in the
evening).
Remedy
Refer to
page
Problem
78
0113V1000RDS_75-80_EN
78
9/5/0, 4:44 PM
30, 31
32
30, 31
TROUBLESHOOTING
■ Remote control
Problem
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m (20 feet) and no
more than 30 degrees off-axis from the front
panel.
8
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition the unit.
—
The batteries are weak.
Replace all batteries with new ones and press
RESET.
3
The internal microcomputer has
“frozen”.
The batteries of this remote control and/or
the other remote control are too weak.
Press RESET on the remote control.
3
Replace the batteries (and press RESET on
the remote control).
3
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper
distance.
58
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
58
Memory capacity is full.
Further learning is not possible without
deleting unnecessary functions.
The internal microcomputer has
“frozen”.
Press RESET on the remote control.
3
The learning process is incomplete.
Be sure to press and hold the function button
on the other remote control until
TRANSMIT begins flashing slowly.
59
59, 62, 63
ADVANCED
OPERATION
After this unit has been exposed to a strong external electric shock (such as lightning and strong static electricity) or if
you mishandle the operation of this unit, it may not function properly. In these cases, set this unit in the standby mode,
disconnect the power cord, plug it back in after 30 seconds, and start operating.
BASIC
OPERAIONT
Continuous functions
such as volume
adjustment are learned,
but operate only for a
moment before
stopping.
Refer to
page
PREPARATION
The remote control does
not “learn” new
functions. (The
TRANSMIT indicator
does not light up nor
flash.)
Remedy
INTRODUCTION
The remote control does
not work nor function
properly.
Cause
ADDITIONAL
INFORMATION
APPENDIX
English
79
0113V1000RDS_75-80_EN
79
9/5/0, 4:44 PM
SPECIFICATIONS
AUDIO SECTION
FM SECTION
• Minimum RMS Output Power for Main, Center, Rear
20 Hz to 20 kHz, 0.04% THD, 8 ohms ............................... 100 W
1 kHz, 0.04% THD, 8 ohms ................................................ 105 W
• Tuning Range .................................................. 87.50 to 108.00 MHz
• DIN Standard Output Power
1 kHz, 0.7% THD, 4 ohms .................................................. 140 W
• IEC Output Power
1 kHz, 0.04%, 8 ohms ......................................................... 105 W
• Dynamic Power (IHF)
8/6/4/2 ohms ................................................... 125/160/195/230 W
• Damping Factor
20 Hz to 20 kHz, 8 ohms .............................................. 80 or more
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono/Stereo ......................... 2.0 µV (17.3 dBf)/25 µV (39.2 dBf)
• Selectivity (400 kHz) ............................................................... 70 dB
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 76 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................. 0.2%/0.3%
• Stereo Separation (1 kHz) ....................................................... 45 dB
• Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB
• Frequency Response
CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB
AM SECTION
• Total Harmonic Distortion
20 Hz to 20 kHz, 50 W, 8 ohms, Main L/R .......................... 0.04%
• Usable Sensitivity ............................................................. 300 µV/m
• Signal to Noise Ratio (IHF-A Network)
PHONO MM to REC OUT (5 mV, shorted) ........................ 81 dB
CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB
GENERAL
• Residual Noise (IHF-A Network)
Main L/R ................................................................ 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD (5.1 kohms terminated) to Main L/R .................. 60 dB/45 dB
• Tuning Range ......................................................... 531 to 1611 kHz
• Power Supply ......................................................... AC 230 V/50 Hz
• Power Consumption .................................................. approx. 300 W
Standby Mode ......................................................... approx. 1.2 W
• AC Outlets (Total 100 W maximum)
[Europe model] ..................................................... 2 (SWITCHED)
[U.K. model] ........................................................ 1 (SWITCHED)
• Tone Control (Main L/R)
BASS Boost/Cut ...................................................... ±10 dB/50 Hz
TREBLE Boost/Cut ............................................... ±10 dB/20 kHz
BASS EXTENSION ................................................. +6 dB/60 Hz
• Dimension (W x H x D)
............................ 435 x 171 x 432 mm (17-1/8” x 6-3/4” x 17”)
• Phones Output ..................................................... 150 mV/100 ohms
• Accessories .............................................................. Remote Control
....................................................................................... Batteries
......................................................................... AM loop antenna
...................................................................... Indoor FM antenna
................ 75-ohm/300-ohm antenna adapter (U.K. model only)
................................................................. Quick Reference Card
• Input Sensitivity
CD, etc .............................................................. 150 mV/47 kohms
PHONO ............................................................. 2.5 mV/47 kohms
6CH INPUT .............................................. 150 mV/40 – 47 kohms
• Output Level
REC OUT ........................................................ 150 mV/0.9 kohms
PRE OUT ............................................................ 2.6 V/1.2 kohms
SUBWOOFER .................................................... 4.0 V/1.2 kohms
• Weight ......................................................................... 15 kg (33 lbs)
* Specifications are subject to change without notice.
VIDEO SECTION
• Video Signal Type ...................................................................... PAL
• Composite Video Signal Level ................................ 1 Vp-p/75 ohms
• S-Video Signal Level
Y ........................................................................... 1 Vp-p/75 ohms
C .................................................................... 0.286 Vp-p/75 ohms
• Component Video Signal Level
Y ........................................................................... 1 Vp-p/75 ohms
PB/CB, PR/CR ....................................................... 0.7 Vp-p/75 ohms
• Signal to Noise Ratio ............................................................... 50 dB
• Frequency Response (MONITOR OUT)
Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB
Component ................................................. DC to 30 MHz, –3 dB
80
0113V1000RDS_75-80_EN
80
9/11/0, 4:44 PM
GB
RX-V1000RDS
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
0100V1000RDS-cv1/4
1
RX-V1000RDS
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Printed in Malaysia ID
V641400
9/11/0, 6:04 PM
Quick Reference Card
■ Remote Control
■ TUNER
RE-NAME
Programming
section
TRANSMIT
indicator
CLEAR
SYSTEM
STANDBY
V-AUX
TUNER
MD/TAPE
D-TV/LD
CBL/SAT
VCR 1
PHONO
POWER
STANDBY
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
LEARN
MACRO
TRANSMIT RE-NAME
CLEAR
LEARN
MACRO
OFF
SYSTEM
POWER
STANDBY
V-AUX
TUNER
MACRO
ON
A and B buttons
STANDBY
■ CD
SYSTEM
POWER
PHONO
6CH INPUT
6CH INPUT
MACRO ON/
OFF
TITLE
TITLE
ENTER
ENTER
SYSTEM POWER
D-TV/LD
CBL/SAT
MD/TAPE
VCR 1
CD-R
VCR 2/DVR
CD
DVD
Input selector
buttons
DISPLAY
SELECT
POWER
6CH INPUT
ENTER
DISPLAY
SOURCE
SELECT k/n
SELECT
POWER
MENU
Preset group A
REC
STOP
Preset group B
SOUND
– CHAPTER +
SEARCH
PAUSE
Operation
section
PLAY
/
10KEY DSP
10KEY/DSP
6.1/ES
6.1/ES
HALL 1
HALL 2
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
11
12
0
+10
+100
CHP/INDEX
+
TV INPUT
–
+
MUTE
CH
TV MUTE
–
EFFECT
ON SCREEN LEVEL
SET MENU
SLEEP
TEST
SELECT
POWER
SOUND
Skip search
– CHAPTER +
SEARCH
POWER
PLAY
MENU
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
/
PLAY
HALL 1
HALL 2
CHURCH
PAUSE
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
10KEY DSP
JAZZ CLUB
+
Preset number
1 to 8
Preset group E
Preset group D
Preset group C
–
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
6.1/ES
/DTS
SUR.
10
11
12
0
+10
+100
A/B/C/D/E PRESET
+
–
–
TV INPUT
TV VOL
+
MUTE
CH
TV MUTE
+
VOLUME
EFFECT
–
STOP
Numeric buttons
1 to 9
Clear
Numeric button +10
Numeric button 0
DISC +/– (disc skip)
–
DISC
DISC
DSP program
group/Numeric
buttons
MOVIE
MOVIE
THEATER 1 THEATER 2
9
CHP/INDEX
*1
VOLUME
EFFECT
INDEX
1
ROCK
CONCERT
■ MD
■ CD-R
SYSTEM
SYSTEM
VOLUME +/–
POWER
STANDBY
PHONO
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
PHONO
–
PARAMETER
SLEEP
TEST
Preset group
A/B/C/D/E
PRESET +/–
+
VOLUME
DISC
PRESET +/–
LEVEL
ON SCREEN
PAUSE
DISPLAY
MUTE
A/B/C/D/E PRESET
TV VOL
Others
/DTS
SUR.
10
STOP
CHP/INDEX
JAZZ CLUB
ROCK
CONCERT
9
A/B/C/D/E
CHURCH
REC
/
10KEY DSP
Display window
SOURCE
– CHAPTER +
SEARCH
POWER
DISPLAY
SEARCH
SOUND
MENU
(YAMAHA: Pause/Stop)
6CH INPUT
TITLE
SOURCE
SOURCE
EFFECT
PARAMETER/
SET MENU
6CH INPUT
6CH INPUT
TITLE
TITLE
Cursor buttons
k/n/–/+
ENTER
ENTER
SOURCE
SOURCE
Setup section
DISPLAY
SEARCH
DISPLAY
SELECT
POWER
POWER
Rec/Pause
SOUND
MENU
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
/
10KEY DSP
6.1/ES
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
*1
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
–
+
Skip search
PLAY
PAUSE
STOP
Numeric buttons
1 to 9
Numeric button
+10
Numeric button 0
DISPLAY
SELECT
POWER
POWER
STOP
6.1/ES
INDEX
Numeric
button 0
SOUND
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
Skip search
PLAY
PAUSE
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
Numeric buttons
1 to 9
Clear
Numeric button +10
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
–
MENU
/
10KEY DSP
*1
VOLUME
EFFECT
DISPLAY
SEARCH
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISC
DISC
V647510
Q-Ref(V1000)-8/24
1
8/30/0, 1:26 PM
Quick Reference Card
■ VCR
■ LD (A)
SYSTEM
■ CBL/SAT (CBSAT)
SYSTEM
SYSTEM
POWER
STANDBY
PHONO
POWER
STANDBY
PHONO
POWER
STANDBY
V-AUX
TUNER
MD/TAPE
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
6CH INPUT
6CH INPUT
TITLE
6CH INPUT
TITLE
TITLE
SOUND
ENTER
SOURCE
DISPLAY
SEARCH
DISPLAY
SELECT
– CHAPTER +
STOP
PAUSE
PLAY
/
HALL 1
HALL 2
CHURCH
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
6.1/ES
MOVIE
MOVIE
THEATER 1 THEATER 2
9
+
TV INPUT
TV VOL
–
SOURCE
SELECT
MENU
11
12
0
+10
+100
+
MUTE
CH
TV MUTE
Numeric buttons
1 to 9
+
REC
Clear
Numeric button
+10
STOP
PLAY
DISPLAY
SELECT
10KEY DSP
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
8
MONO
MOVIE
TV/Video input
MOVIE
MOVIE
THEATER 1 THEATER 2
9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
*1
–
TV INPUT
TV VOL
–
+
MUTE
CH
TV MUTE
+
VOLUME
EFFECT
–
–
SOUND
MENU
– CHAPTER +
SEARCH
PHONO
POWER
STANDBY
TUNER
MD/TAPE
CD-R
CD
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
6CH INPUT
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
/
PAUSE
Return
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
ROCK
CONCERT
5
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
TV INPUT
TV VOL
–
Audio
Skip search
PLAY
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
–
DISPLAY
SELECT
POWER
POWER
DISC +/–
(disc skip)
– CHAPTER +
SEARCH
REC
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
STADIUM
ENTERTAINMENT
TV
SPORTS
6
7
ROCK
CONCERT
5
Enter
TV INPUT
SOUND
MENU
/
10KEY DSP
STOP
Numeric buttons
1 to 9
Clear
Numeric button
+10
DISPLAY
6.1/ES
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
A/B/C/D/E PRESET
+
TV VOL +/–
–
DISC
TV INPUT
TV VOL
+
MUTE
CH
TV MUTE
–
STOP
PAUSE
PLAY
HALL 1
HALL 2
CHURCH
JAZZ CLUB
1
2
3
4
ROCK
CONCERT
STADIUM
ENTERTAINMENT
TV
SPORTS
5
6
7
MONO
MOVIE
MOVIE
MOVIE
THEATER 1 THEATER 2
9
8
Numeric buttons
1 to 9
/DTS
SUR.
10
11
12
0
+10
+100
CHP/INDEX
*2
Recall
Numeric button 0
A/B/C/D/E PRESET
+
*1
TV INPUT
TV VOL
+
MUTE
CH
TV MUTE
–
+
VOLUME
EFFECT
CH +/– (channel)
–
*1
• TV VOL +/–, TV INPUT, and TV MUTE function if you have set up the
manufacturer code for your TV in the D-TV/LD or PHONO area.
• Commandes TV VOL +/–, TV INPUT et TV MUTE si l’on a programmé le code
fabricant du téléviseur dans la section D-TV/LD ou PHONO.
• TV VOL +/–, TV INPUT- und TV MUTE-Funktion, falls Sie den Herstellercode
für Ihr Fernsehgerät im Bereich D-TV/LD oder PHONO eingestellt haben.
• Knapparna TV VOL +/–, TV INPUT och TV MUTE fungerar om du ställt in
tillverkarkoden för din TV i D-TV/LD-området eller PHONO-området.
• TV VOL +/–, TV INPUT e TV MUTE sono operativi se nell’area D-TV/LD o
PHONO è stato impostato il codice del fabbricante del televisore di cui si
dispone.
• Funciones TV VOL +/–, TV INPUT y TV MUTE si ha ajustado el código de
fabricante para su televisor en el área D-TV/LD o PHONO.
• TV VOL +/– (tv-volumeniveau), TV INPUT (tv-ingangsbron) en TV MUTE (tvdempingsfunctie) als u de fabrikantcode voor uw tv hebt ingesteld in het D-TV/
LD- of PHONO-bedieningsgedeelte.
•
ENTER
SOUND
MENU
6.1/ES
–
SOURCE
SELECT
6.1/ES
CH +/– (channel)
TITLE
ENTER
DISPLAY
10KEY DSP
Enter
PHONO
6CH INPUT
SOURCE
10KEY DSP
Numeric button
10 or 0
REC
/
Numeric buttons
1 to 9
SYSTEM
STANDBY
V-AUX
Menu cursor/
ENTER
POWER
STOP
■ TV (TV/LD)
TITLE
POWER
DISC
POWER
POWER
PAUSE
DISC
TITLE
*1
PAUSE
/
6.1/ES
VOLUME
EFFECT
–
POWER
REC
(Press twice to start
recording)
SYSTEM
Title/Index
Numeric button 0
DISPLAY
SOUND
– CHAPTER +
SEARCH
POWER
■ DVD
POWER
Menu cursor/
Menu select
ENTER
SOURCE
DISPLAY
DISC
MENU
DISPLAY
SEARCH
MENU
ENTER
Rewind/Fast
forward
/DTS
SUR.
10
CHP/INDEX
PLAY
PAUSE
JAZZ CLUB
A/B/C/D/E PRESET
*1
CHAPTER –/+
(chapter search)
PLAY
REC
10KEY DSP
Chapter/Time
Numeric button 0
SOUND
SEARCH
POWER
POWER
STOP
MENU
PHONO
+
VOLUME
EFFECT
*2
Numeric buttons
1 to 9
Numeric button
10 or 0
CH +/– (channel)
–
DISC
TV MUTE
*2
• You can control your VCR if you have set up the code for VCR 1.
• Permet de commander le magnétoscope si l’on a programmé le code fabricant
pour VCR 1.
• Sie können Ihren Videorecorder bedienen, falls Sie den Code für VCR 1
eingestellt haben.
• Du kan styra din videobandspelare om du ställt in koden för VCR 1.
• Se è stato impostato il codice di VCR 1 è possibile comandare il
videoregistratore di cui si dispone.
• Puede controlar su videorreproductor si ha ajustado el código para VCR 1.
• U kunt uw videorecorder bedienen als u de fabrikantcode voor VCR 1 hebt
ingesteld.
•
V647510
Q-Ref(V1000)-8/24
2
8/30/0, 1:26 PM
Download PDF