Crestron | DM-RMC-200-S2 | Installation guide | Crestron DM-RMC-200-S2 Installation guide

Crestron DM-RMC-200-S2 Installation guide
Crestron DM-RMC-200-S/S2
DigitalMedia 8G™ Fiber Receiver
& Room Controller 200
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Important Safety Instructions
WARNING:
•
Read these instructions.
•
Keep these instructions.
•
Heed all warnings.
•
Follow all instructions.
•
Do not use this apparatus near water.
•
Clean only with dry cloth.
•
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
•
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
•
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. THE APPARATUS SHALL NOT BE
EXPOSED TO DRIPPING OR SPLASHING. OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD
NOT BE PLACED ON THE APPARATUS.
•
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
•
Only use attachments/accessories specified by the
manufacturer.
•
Use only with the cart, stand, tripod, bracket or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
•
Unplug this apparatus during lightning storms or when unused
for long periods of time.
•
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
•
Disconnect power prior to connecting or disconnecting
equipment.
•
Do not install in direct sunlight.
•
The apparatus must be installed in a way that the power cord
can be removed either from the wall outlet or from the device
itself in order to disconnect the mains power.
•
Prevent foreign objects from entering the device.
WARNING:
TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE
COVER. THERE ARE NO USER SERVICEABLE PARTS
INSIDE. ONLY QUALIFIED SERVICE PERSONNEL
SHOULD PERFORM SERVICE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT
This device can be used with Class 2 output wiring.
This device includes an aggregation of separate independent works that are each generally copyrighted by Crestron Electronics, Inc., with all rights
reserved. One of those independent works, Linux Bridge Project, is copyrighted under the GNU GENERAL PUBLIC LICENSE, Version2,
reproduced in “GNU General Public License” on page 34, where the corresponding source code is available at: ftp://ftp.crestron.com/gpl.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, CresFiber, Crestron e-Control, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, DM, DM 8G, and Excite are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby and Dolby Digital are either trademarks or registered
trademarks of Dolby Laboratories in the United States and/or other countries. DTS and DTS-HD Master Audio are either trademarks or registered trademarks of
DTS, Inc. in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the
United States and/or other countries. Windows is either a trademark or registered trademark of Microsoft Corporation in the United States and/or other countries.
Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of others.
©2012 Crestron Electronics, Inc.
Regulatory Compliance
Compliance
Regulatory
As of the date of manufacture, the DM-RMC-200-S and DM-RMC-200-S2 have been tested and found to comply
with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling.
Federal
Federal Communications
Communications Commission
Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
Industry Canada (IC) Compliance Statement
CAN-ICES-3 (A)/NMB-3(A)
The DM-RMC-200-S and DM-RMC-200-S2 are class 1 laser products. They comply with safety regulations of
IEC-60825-1, FDA 21 CFR 1040.11 and FDA 21 CFR 1040.10.
WARNING: Visible and invisible laser radiation when open. Avoid direct exposure to beam.
NOTE: Plug the included dust cap into the optical transceiver when the fiber optic cable is unplugged.
WARNING: These are class A products. In a domestic environment these products may cause radio interference
in which case the user may be required to take adequate measures.
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Contents
DigitalMedia 8G Fiber Receiver & Room Controller 200:
DM-RMC-200-S/DM-RMC-200-S2
1
Introduction ............................................................................................................................... 1
Features and Functions ................................................................................................ 1
Applications................................................................................................................. 5
Specifications .............................................................................................................. 6
Physical Description.................................................................................................. 10
Setup ........................................................................................................................................ 17
Network Wiring......................................................................................................... 17
Identity Code ............................................................................................................. 17
Supplied Hardware .................................................................................................... 18
Installation ................................................................................................................. 18
Hardware Hookup ..................................................................................................... 21
Programming Software ............................................................................................................ 23
Software Requirements for the PC ............................................................................ 23
Programming with SIMPL Windows ........................................................................ 23
Uploading and Upgrading........................................................................................................ 26
Establishing Communication..................................................................................... 26
Firmware ................................................................................................................... 29
IP Configuration ........................................................................................................ 29
Problem Solving ...................................................................................................................... 30
Troubleshooting......................................................................................................... 30
Reference Documents................................................................................................ 31
Further Inquiries ........................................................................................................ 31
Future Updates .......................................................................................................... 32
Return and Warranty Policies .................................................................................................. 33
Merchandise Returns / Repair Service ...................................................................... 33
Crestron Limited Warranty........................................................................................ 33
GNU General Public License .................................................................................................. 34
Operations & Installation Guide – DOC. 7246B
Contents  i
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DigitalMedia 8G Fiber Receiver
& Room Controller 200:
DM-RMC-200-S/DM-RMC-200-S2
Introduction
The DM-RMC-200-S/DM-RMC-200-S2, hereinafter referred to simply as the DM®
receiver unless otherwise indicated, provides an advanced one-box interface solution
for a single display device as part of a complete Crestron® DigitalMedia™ system.
It functions as a DM 8G® (DM-RMC-200-S)/DM 8G SM (DM-RMC-200-S2) fiber
receiver, video scaler, audio amplifier, and control interface, providing a single
HDMI® output along with speaker and line level audio plus Ethernet, USB HID, and
a variety of control ports. Built-in scaling enables the connected display to handle
virtually any video signal. A compact, low-profile design allows the DM receiver to
be installed discreetly behind a flat panel display or above a ceiling mounted
projector. It connects to the head end or source location using one multimode
(DM-RMC-200-S) or single-mode (DM-RMC-200-S2) fiber strand.1
Features and Functions






DigitalMedia 8G™ multimode (DM-RMC-200-S)/single-mode
(DM-RMC-200-S2) fiber receiver, high-definition scaler, audio
amplifier, and display controller
DM 8G fiber input supports up to 1000 foot (~300 meter) cable length
(DM-RMC-200-S)1
DM 8G SM fiber input supports up to 7.5 miles (12 km) cable length
(DM-RMC-200-S2)1
Connects to a DM switcher or transmitter (each sold separately) over one
multimode (DM-RMC-200-S)/single-mode (DM-RMC-200-S2)
fiber strand1
Provides one HDMI or DVI display output2
Accepts any video source from standard NTSC 480i or PAL 576i to
HD 1080p60 with Deep Color
(Continued on following page)
1. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. The manual is
available from the Crestron Web site at www.crestron.com/dmresources. All wire and cables sold
separately.
2. HDMI requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cable sold separately.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  1
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Features and Functions
(Continued)




















Accepts any computer source from VGA to UXGA/WUXGA
Scales the source to match the native resolution of virtually any popular
video display or computer monitor
Provides intelligent frame rate conversion
Allows motion-adaptive de-interlacing or interlacing
Allows adjustable overscan or underscan up to 7.5%
Provides automatic 3D to 2D signal conversion1
Automatically passes 3D video without scaling to 3D capable displays1
Includes content-adaptive noise reduction
100% HDCP compliant
Scalable zoom feature enables 2 x 2, 3 x 2, 3 x 3, 4 x 3, or 4 x 4 video
wall capability2
Handles Dolby® TrueHD, DTS-HD Master Audio™, and uncompressed
7.1 linear PCM audio
Provides a stereo analog line level audio output
Includes a built-in 30 watt stereo amplifier
Provides 10BASE-T/100BASE-TX Ethernet and USB HID (Human
Interface Device) mouse/keyboard ports
Enables device control via CEC, IR, RS-232, and Ethernet
Provides two relay control ports and two contact sensing inputs
Allows quick, easy setup and diagnostics
Low-profile design mounts to a 2-gang US, UK, or European
electrical box
Includes mounting bracket with integral power pack holder
Universal power pack included
DigitalMedia 8G Multimode/Single-Mode Fiber
DigitalMedia 8G provides a true one-wire transport for moving high-definition
video, audio, and Ethernet over fiber optic cable without compression or repeaters.
Engineered for ultra high bandwidth and ultimate scalability, DM 8G handles
uncompressed video beyond high definition with support for HDCP, Deep Color,
and 3D1. Audio capabilities include support for high-bitrate 7.1 audio formats such
as Dolby® TrueHD and DTS-HD Master Audio ™ as well as uncompressed linear
PCM. All DM-RMC-200-S signals are transported over one strand of multimode
fiber, supporting distances up to 1000 feet (~300 meters) using CresFiber® 8G fiber
optic cable.3 All DM-RMC-200-S2 signals are transported over one strand of
single-mode fiber, supporting distances up to 7.5 miles (12 km) using CresFiber 8G
SM or G.652.D single-mode fiber optic cable. 3
1. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D to 2D conversion (with scaling) if display device does not
support 3D.
2. Video wall processing requires a separate DM receiver for each individual display.
3. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables
sold separately.
2  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Multimedia Display Interface
A single HDMI digital AV output port is provided on the DM receiver, supporting
HD 1080p60 video and WUXGA computer signals with HDCP, Deep Color, 3D1,
and multichannel HD lossless audio—all through one connection. The HDMI output
can also handle DVI signals using an appropriate adapter or interface cable.2
Stereo audio outputs are also provided for directly driving a pair of speakers or for
connecting to line inputs on the display or a separate amplifier or AV receiver.
A single fiber strand connects the DM receiver to a DM switcher or transmitter (each
sold separately), transporting video, audio, control, and networking signals through
one SC type (DM-RMC-200-S)/LC type (DM-RMC-200-S2) optical connection.3
Multiple DM receivers may be installed to handle each display in a multiroom
distribution system, all fed from a central DM switcher (sold separately). Or, a single
DM receiver can be fed straight from a DM fiber transmitter (DM 8G transmitter
sold separately for the DM-RMC-200-S or DM 8G SM transmitter sold separately
for the DM-RMC-200-S2) to extend a computer or AV signal to a single display.
High-Definition Scaler
Through a distributed scaler approach, DigitalMedia technology delivers a flexible
and user-friendly solution for routing multiple disparate sources to many different
display devices. By placing an independent high-performance scaler at every display
device, DM ensures an optimal image on every screen regardless of the sources that
are selected. Distributed scaling allows a high-resolution computer source to be
viewed on any display in the building. It also allows a high-definition 3D source to
be viewed on lower resolution 2D displays without compromising the original signal.
The DM receiver accepts any video source from standard NTSC 480i to HD
1080p60 with Deep Color, as well as computer sources from VGA to
UXGA/WUXGA, and scales them perfectly to match the native resolution of the
video display. A range of common output resolutions is supported to work with
virtually any popular flat panel display, projector, or computer monitor. Intelligent
frame rate conversion enables support for 24p and PAL format sources, and 3D to
2D conversion allows 3D content to be fed simultaneously to separate 3D and 2D
displays. Setup and use of the scaler is simplified through fully automatic operation
utilizing the display’s EDID.1, 4
A pair of DM receivers can also be used to facilitate a dual-projector 3D setup,
steering the left eye portion of a 3D signal to one projector and the right eye portion
to the other. This is done using the scaler’s 3D to 2D conversion mode, enabling 3D
capability with scaling.
1. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D to 2D conversion (with scaling) if display device does not
support 3D.
2. HDMI requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cable sold separately.
3. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables
sold separately.
4. EDID (Extended Display Identification Data) is data embedded in an HDMI, DVI, or VGA signal that
enables a display device to tell the source device what resolutions and formats it can support, allowing
the source to configure itself automatically to feed the best signal that both devices can support.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  3
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Video Wall Processing
The DM receiver provides zoom capability on its output to display just a portion of
the source image. Using this feature, multiple units may be combined to configure a
high-definition video wall composed of up to 16 individual displays. Configurations
of 2 x 2, 3 x 2, 3 x 3, 4 x 3, or 4 x 4 are supported, and all that is required is a
separate DM receiver for each display and a DM switcher (sold separately) with
sufficient DM 8G/DM 8G SM fiber outputs.
Audio Amplifier
The DM receiver is equipped with stereo analog audio outputs and a built-in 30 watt
stereo amplifier. The output volume is adjustable via a control system using a
keypad, touch screen, or handheld remote. The amplifier provides plenty of power to
drive a pair of local speakers, or the line output can be used to connect directly to the
display device, a pair of amplified speakers, or a local sound system.
LAN Connectivity
Along with high-definition AV and control, DigitalMedia technology also integrates
high-speed Ethernet networking for a total signal distribution solution. The DM
receiver includes a 10BASE-T/100BASE-TX Ethernet port, providing a convenient
LAN connection for a local network device.
Keyboard/Mouse Extender
The DM receiver also functions as a keyboard/mouse extender, allowing a USB
HID-compliant keyboard and/or mouse to be connected at the display location and
used to control a computer or other component located at the central equipment rack
or some other location.
Embedded Device Control
The DM receiver includes built-in RS-232, IR, and Ethernet control ports to allow
programmable control of the display device connected to it. It can also provide an
alternative to such conventional control methods by harnessing the CEC (Consumer
Electronics Control) signal embedded in HDMI. Through its connection to the
control system, the DM receiver provides a gateway for controlling the display
device through the HDMI connection, potentially eliminating the need for any
dedicated control wires or IR emitters.
Two low-voltage relay ports are also included on the DM receiver for control of a
projection screen or lift. In addition, there are two discrete digital input ports to
accommodate room occupancy sensors, power sensors, or contact closures for
enhanced automation and monitoring.
Low-Profile Installation
Its low-profile design makes the DM receiver perfect for installation behind a flat
panel display or above a ceiling mounted projector. It mounts to a standard 2-gang
US, UK, or European electrical box using the mounting bracket provided. The
bracket includes a convenient holder for the external power pack, providing for a
clean installation that protrudes only 1.6 inches (~41 mm) from the mounting
surface.
Connections are positioned on the top, bottom, and rear of the unit. The design of the
mounting bracket allows wires up to 0.23 inches (~6 mm) in diameter to extend from
the electrical box as needed. An array of indicators is provided on the front of the
DM receiver for easy setup and troubleshooting.
4  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Applications
The diagram below shows a DM-RMC-200-S in a standalone application. In this
type of application, the DM-RMC-200-S is used with a DM 8G fiber transmitter
such as the DM-TX-201-S (sold separately) and is not used with a DM switcher.
DM-RMC-200-S in a Standalone Application
In a DM-RMC-200-S2 standalone application, the DM-RMC-200-S2 is used with a
DM 8G SM fiber transmitter such as the DM-TX-201-S2 (sold separately) and is not
used with a DM switcher.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  5
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Specifications
Specifications for the DM receiver are listed in the following table.
DM-RMC-200-S/DM-RMC-200-S2 Specifications
SPECIFICATION
DETAILS
Video
Scaler1
HD video scaler, motion-adaptive
deinterlacer, interlacer, intelligent frame
rate conversion, Deep Color support,
2
3D to 2D conversion , content-adaptive
noise reduction, widescreen format
selection (zoom, stretch, maintain
aspect ratio, or 1:1), video wall
processing (2 x 2, 3 x 2, 3 x 3, 4 x 3, or
4 x 4)3
Input Signal Type
DM-RMC-200-S: DM 8G fiber
(DigitalMedia over one multimode fiber
optic strand)4
DM-RMC-200-S2: DM 8G SMF
(DigitalMedia over one single-mode fiber
optic strand)4
HDMI, DVI5
Output Signal Types
Formats
HDMI with Deep Color & 3D2, DVI,
HDCP content protection support
Input Resolutions
Progressive
640 x 480 @ 60 Hz
720 x 480 @ 60 Hz (480p)
720 x 576 @ 50 Hz (576p)
800 x 600 @ 60 Hz
848 x 480 @ 60 Hz
852 x 480 @ 60 Hz
854 x 480 @ 60 Hz
1024 x 768 @ 60 Hz
1024 x 852 @ 60 Hz
1024 x 1024 @ 60 Hz
1280 x 720 @ 50 Hz (720p50)
1280 x 720 @ 60 Hz (720p60)
1280 x 768 @ 60 Hz
1280 x 800 @ 60 Hz
1280 x 960 @ 60 Hz
1280 x 1024 @ 60 Hz
1360 x 768 @ 60 Hz
1365 x 1024 @ 60 Hz
1366 x 768 @ 60 Hz
1400 x 1050 @ 60 Hz
1440 x 900 @ 60 Hz
1600 x 900 @ 60 Hz
1600 x 1200 @ 60 Hz
1680 x 1050 @ 60 Hz
1920 x 1080 @ 24 Hz (1080p24)
1920 x 1080 @ 25 Hz (1080p25)
1920 x 1080 @ 50 Hz (1080p50)
1920 x 1080 @ 60 Hz (1080p60)
1920 x 1200 @ 60 Hz
plus any other resolution allowed by
HDMI up to 165 MHz pixel clock
(Continued on following page)
6  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued)
SPECIFICATION
DETAILS
Video
Input Resolutions (Continued)
720 x 480 @ 30 Hz (480i)
720 x 576 @ 25 Hz (576i)
1920 x 1080 @ 25 Hz (1080i25)
1920 x 1080 @ 30 Hz (1080i30)
plus any other resolution allowed by
HDMI up to 165 MHz pixel clock
Interlaced
Scaler Output Resolutions
Progressive
640 x 480 @ 60 Hz
720 x 480 @ 60 Hz (480p)
720 x 576 @ 50 Hz (576p)
800 x 600 @ 60 Hz
848 x 480 @ 60 Hz
1024 x 768 @ 60 Hz6
1280 x 720 @ 50 Hz (720p50)
1280 x 720 @ 60 Hz (720p60)
1280 x 768 @ 60 Hz
1280 x 800 @ 60 Hz6
1280 x 960 @ 60 Hz
1280 x 1024 @ 60Hz
1360 x 768 @ 60 Hz
1366 x 768 @ 60 Hz6
1400 x 1050 @ 60 Hz6
1440 x 900 @ 60 Hz6
1600 x 900 @ 60 Hz7
1600 x 1200 @ 60 Hz
1680 x 1050 @ 60 Hz6
1920 x 1080 @ 50 Hz (1080p50)
1920 x 1080 @ 60 Hz (1080p60)
7
1920 x 1200 @ 60 Hz
2048 x 1152 @ 60 Hz7
Interlaced
720 x 480 @ 30 Hz (480i)
720 x 576 @ 25 Hz (576i)
1920 x 1080 @ 25 Hz (1080i25)
1920 x 1080 @ 30 Hz (1080i30)
Pass-Thru Output Resolutions
Matched to input
Audio
Input Signal Type
DM-RMC-200-S: DM 8G fiber
DM-RMC-200-S2: DM 8G SMF
Output Signal Types
HDMI, analog stereo (speaker and
line level)
Formats
HDMI
Dolby Digital®, Dolby Digital EX, Dolby
Digital Plus, Dolby® TrueHD, DTS®,
DTS-ES, DTS 96/24, DTS-HD High Res,
DTS-HD Master Audio™, up to 8ch PCM
Analog
Stereo 2-Channel
Digital-to-Analog Conversion
24-bit 48 kHz
(Continued on following page)
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  7
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued)
SPECIFICATION
Audio (Continued)
Performance (Analog)
Amplifier Output Power8
Frequency Response
S/N Ratio
THD+N
Stereo Separation
Volume Gain Range (Analog)
Communications
DigitalMedia
Ethernet
USB
Power Requirements
Power Pack
Minimum 2-Series Control System
Update File9, 10
Environmental
Temperature
Humidity
Heat Dissipation
Enclosure
Chassis
Mounting
Dimensions
Height
Width
Depth
Weight
Included Accessory
DETAILS
15 watts per channel at 8 ohms
20 Hz to 20 kHz ±0.5 dB (line),
20 Hz to 16 kHz ±3 dB (speaker)
>95 dB (line), >75 dB (speaker)
20 Hz to 20 kHz A-weighted
<0.005% @ 1 kHz (line),
<0.3% @ 1 kHz (speaker)
>90 dB (line), >60 dB (speaker)
-80 dB to 0 dB
DM 8G fiber (DM-RMC-200-S)/
DM 8G SMF (DM-RMC-200-S2), HDCP
management, EDID format management,
CEC
10BASE-T/100BASE-TX, auto-switching,
auto-negotiating, auto-discovery,
full/half duplex, DHCP
Supports USB HID class devices
2 A @ 24 volts dc;
100-240 volts ac, 50/60 Hz power pack
included
Version 4.003.0029 or later
32º to 104º F (0º to 40º C)
10% to 90% RH (non-condensing)
Power amp off, no relay or USB loads:
60 Btu/h;
Power amp on, with relay and USB loads:
80 Btu/h (maximum)
Metal, black finish, vented sides and front
Mounts to a 2-gang electrical box,
2-gang UK (BS 4662) electrical box,
or 2-gang European (DIN 49073)
electrical box;
Bracket includes holder for the included
power pack
7.92 in (201 mm)
10.83 in (275 mm) with mounting bracket
1.73 in (44 mm) with mounting bracket
3.3 lb (1.5 kg) including bracket and
power pack
Universal 24 Volt DC Power Pack
(Continued on following page)
8  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued)
SPECIFICATION
DETAILS
Available Accessories
CBL Series
Crestron Certified Interface Cables
CNSP-XX
Custom Serial Interface Cable
CRESFIBER-CONNSC50UM-12
(DM-RMC-200-S only) CresFiber Fiber
Optic Cable Connector
CRESFIBER-SINGLE-SC
(DM-RMC-200-S only) CresFiber Simplex
Fiber Optic Cable Assembly, 50/125, SC
CRESFIBER-SINGLESC-ARMORED
(DM-RMC-200-S only) CresFiber
ARMORED Simplex Fiber Optic Cable
Assembly, 50/125, SC
CRESFIBER-SINGLESC-CLEAR
(DM-RMC-200-S only) CresFiber CLEAR
Simplex Fiber Optic Cable Assembly,
50/125, SC
CRESFIBER-SM-CONNLC-12
(DM-RMC-200-S2 only) CresFiber
Single-Mode Fiber Optic Cable
Connector
CRESFIBER-TK
CresFiber Termination Kit
CRESFIBER8G
(DM-RMC-200-S only) CresFiber 8G
Fiber Optic Cable
CRESFIBER8G-SM
(DM-RMC-200-S2 only) CresFiber 8G
Single-Mode Fiber Optic Cable
IRP2
IR Emitter Probe
MP-WP Series
Media Presentation Wall Plates
MPI-WP Series
Media Presentation Wall Plates –
International Version
1. Using the DMTool in Crestron Toolbox™, the scaler can be enabled/disabled.
2. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D to 2D conversion (with scaling) if display device does not
support 3D.
3. Video wall processing requires a separate DM receiver for each individual display.
4. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables
sold separately.
5. HDMI requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cable sold separately.
6. With or without reduced blanking.
7. With reduced blanking only.
8. Using the DMTool in Crestron Toolbox, the amplifier can be enabled/disabled.
9. The latest software versions can be obtained from the Crestron Web site. Refer to the NOTE
following these footnotes.
10. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product
Catalog for a complete list of 2-Series control systems.
NOTE: Crestron software and any files on the Web site are for authorized Crestron
dealers and Crestron Authorized Independent Programmers (CAIPs) only. New users
may be required to register to obtain access to certain areas of the site (including the
FTP site).
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  9
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Physical Description
This section provides information on the connections, controls and indicators
available on the DM receiver.
DM-RMC-200-S/DM-RMC-200-S2 Physical View (Front Panel)
DM-RMC-200-S
DM-RMC-200-S2
10  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Physical View (Rear Panel)
DM-RMC-200-S/DM-RMC-200-S2 Physical View (Top Panel)
DM-RMC-200-S
DM-RMC-200-S2
DM-RMC-200-S/DM-RMC-200-S2 Physical View (Bottom Panel)
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  11
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
DM-RMC-200-S/DM-RMC-200-S2 Overall Dimensions (Front and Side Panels without Mounting Bracket Installed)
7.60 in
(193 mm)
7.45 in
(190 mm)
7.92 in
(201 mm)
7.54 in
(192 mm)
1.05 in
( 27 mm)
1.46 in
(37 mm)
DM-RMC-200-S/DM-RMC-200-S2 Overall Dimensions (Front and Side Panels with Mounting Bracket Installed)
10.83 in
(275 mm )
1.30 in
(33 mm)
4.93 in
(126 mm)
3.30 in
(84 mm)
1.23 in
(32 mm)
1.53 in
(39 mm)
1.62 in
(41 mm)
1.73 in
(44 mm)
12  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Front Panel)
1
2
3
4
5
6
DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Top Panel)
DM-RMC-200-S
7
9
8
11
12
11
12
10
DM-RMC-200-S2
7
13
8
10
DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Bottom Panel)
14
Operations & Installation Guide – DOC. 7246B
15
16
17
18
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  13
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Rear Panel)
19
20
21
22
Connectors, Controls & Indicators
#
CONNECTORS1,
CONTROLS &
INDICATORS
1
PWR LED
2
DM LINK LED
3
VIDEO LED
4
USB HID LED
(1) Green LED, indicates a valid device
connection and activity on the USB HID
port
5
SETUP
(LED and Button)
(1) Red LED and (1) miniature recessed
push button for Ethernet setup
6
RESET
(1) Miniature recessed push button for
hardware reset
7
AUDIO OUT R, L
(Speaker)2
(2) 2-pin 5 mm detachable terminal
blocks;
Left and right speaker level audio
outputs;
Paralleled with rear panel AUDIO OUT
connectors;
Wire Size: Connector accepts 12 AWG
maximum;
Output Power: 15 watts per channel at
8 ohms
DESCRIPTION
(1) Green LED, indicates operating
power supplied from local power pack
(1) Green LED, indicates DM link status
(1) Green LED, indicates video signal
presence and lock status
(Continued on following page)
14  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Connectors, Controls & Indicators (Continued)
#
CONNECTORS1,
CONTROLS &
INDICATORS
8
AUDIO OUT R, L
(Line)
9
DM IN MMF/SC
(DM-RMC-200-S only)
(1) SC female optical fiber connector;
DM 8G fiber input;
Connects to DM 8G fiber output of a DM
switcher, transmitter, or other DM device
via CresFiber 8G multimode fiber optic
cable3
10
DM IN LED
(1) Green LED, indicates DM link status
11
LAN
Pin 1
Amber
LED
Pin 8
Green
LED
DESCRIPTION
(2) RCA female;
Stereo unbalanced line level audio
output;
Output Level: 2 Vrms maximum
Output Impedance: 100 ohms nominal
(1) 8-pin RJ-45 female, shielded, with
two LED indicators;
10BASE-T/100BASE-TX Ethernet port;
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity
PIN
SIGNAL
PIN
SIGNAL
1
2
3
4
TX +
TX RX +
N/C
5
6
7
8
N/C
RX N/C
N/C
12
24 V
2.0A MAX
13
DM IN SMF/LC
(DM-RMC-200-S2 only)
(1) LC female optical fiber connector;
DM 8G single-mode fiber input;
Connects to DM 8G SMF output of a DM
switcher, transmitter, or other DM device
via CresFiber 8G SM single-mode fiber
3
optic cable
14
DIG IN
(1) 2-pin 3.5 mm detachable terminal
block;
Digital/contact closure sensing input;
Rated for 0-24 volts dc, referenced
to GND;
Input Impedance: 2.2k ohms pulled up to
5 volts dc;
Logic Threshold: 2.5 volts dc nominal
with 1 volt hysteresis band
SG
15
HDMI OUT
16
USB HID
(1) 2.1 x 5.5 mm dc power connector;
24 volt dc power input;
Power pack included
(1) 19-pin Type A HDMI female;
HDMI digital video/audio output;
Also supports DVI4
(1) USB Type A female;
USB 2.0 host port for connection of a
mouse/keyboard or other USB
HID-compliant device
(Continued on following page)
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  15
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Connectors, Controls & Indicators (Continued)
#
CONNECTORS1,
CONTROLS &
INDICATORS
17
COM
(1) 5-pin 3.5 mm detachable terminal
block, bidirectional RS-232 port;
Up to 115.2k baud, hardware and
software handshaking support
18
IR 1-2
(1) 4-pin 3.5 mm detachable terminal
block comprising two IR/Serial ports;
IR output up to 1.1 MHz;
1-way serial TTL/RS-232 (0-5 volts) up to
19200 baud5
19
G
20
AUDIO OUT L, R
(Speaker) 2
21
DIG IN
SG
22
RELAY 1-2
DESCRIPTION
(1) 06-32 screw, chassis ground lug
(2) 2-pin 5 mm detachable terminal
blocks;
Left and right speaker level audio
outputs;
Paralleled with top panel AUDIO OUT
(Speaker) connectors;
Wire Size: Connector accepts 12 AWG
maximum;
Output Power: 15 watts per channel at
8 ohms
(1) 2-pin 3.5 mm detachable terminal
block;
Digital/contact closure sensing input;
Rated for 0-24 volts dc, referenced
to GND;
Input Impedance: 2.2k ohms pulled up to
5 volts dc;
Logic Threshold: 2.5 volts dc nominal
with 1 volt hysteresis band
(1) 4-pin 3.5 mm detachable terminal
block comprising two normally open,
isolated relays;
Rated 1 amp, 30 volts ac/dc;
MOV arc suppression across contacts
1. Interface connectors for the AUDIO OUT (Speaker), DIG IN, COM, IR, and RELAY ports are
provided with the unit.
2. The set of speaker level audio outputs on the top panel and the set of speaker level audio outputs on
the rear panel cannot be used simultaneously. Either set of speaker level audio outputs should be used
at one time.
3. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables
sold separately.
4. HDMI requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cable sold separately.
5. Maximum string length for serial commands sent via the IR port should be no greater than
40 characters.
16  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Setup
Network Wiring
When wiring the DM network, consider the following:

Use Crestron Certified Wire.

Use Crestron power supplies for Crestron equipment.
CAUTION: Failure to use Crestron power supplies could cause equipment
damage or void the Crestron warranty.

Provide sufficient power to the system.

For DigitalMedia 8G multimode fiber wiring, CresFiber 8G is
recommended. Refer to the following table for the maximum transmission
distance of CresFiber 8G and other fiber optic cable.
DigitalMedia 8G Multimode Fiber Wiring and Maximum Transmission Distance
CABLE TYPE
CresFiber 8G

MAXIMUM TRANSMISSION DISTANCE
1000 feet (~300 meters)
CresFiber
500 feet (~150 meters)
Generic OM3
500 feet (~150 meters)
For DigitalMedia 8G single-mode fiber wiring, CresFiber 8G SM is
recommended. The maximum transmission distance of CresFiber 8G SM or
generic G.652.D (or better) single-mode fiber optic cable is 7.5 miles
(12 km).
Refer to the latest version of the Crestron DigitalMedia Design Guide (Doc. 4546)
for complete system design guidelines.
The DM receiver also uses high-speed Ethernet for communications between the
device and a control system, computer, media server, and other IP-based devices. For
general information on connecting Ethernet devices in a Crestron system, refer to the
latest version of the Crestron e-Control Reference Guide (Doc. 6052), which is
available from the Crestron Web site (www.crestron.com/manuals). For information
specifically related to Ethernet connectivity using DigitalMedia devices, refer to the
latest version of the Crestron IP Considerations Guide for the IT Professional (Doc.
4579), which is also available from the Crestron Web site
(www.crestron.com/dmresources).
Identity Code
NOTE: In the SIMPL Windows program, the IP ID of the DM receiver is assigned
automatically and does not require additional programming when the DM receiver is
dropped onto an output card of a DM switcher. Use the information below when the
DM receiver is dropped directly into an Ethernet slot on the control system in
SIMPL Windows without a DM switcher.
The IP ID is set within the IP table of the DM receiver using Crestron Toolbox™.
For information on setting an IP table, refer to the Crestron Toolbox help file. The IP
IDs of multiple DM receivers in the same system must be unique.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  17
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
When setting the IP ID, consider the following:

The IP ID of each unit must match an IP ID specified in the SIMPL
Windows program.

Each device using IP to communicate with a control system must have a
unique IP ID.
Supplied Hardware
The hardware supplied with the DM receiver is listed in the following table.
Supplied Hardware for the DM-RMC-200-S/DM-RMC-200-S2
DESCRIPTION
PART NUMBER
QUANTITY
Mounting Bracket
2032478
1
Screws, 06-32 x 1/4”, Pan, Phil
2007215
4
Screws, 06-32 x 1”, Pan, Phil
2007250
2
Screws, 06-32 x 3/4”, Slot
2009211
4
Standoffs, 06-32 x 1-1/4”
2007056
4
Tie Wraps
2013608
2
Installation
Ventilation
The DM receiver should be used in a well-ventilated area. The venting holes should
not be obstructed under any circumstances.
To prevent overheating, do not operate this product in an area that exceeds the
environmental temperature range listed in the table of specifications.
Mounting
The DM receiver mounts to a 2-gang electrical box (not included). To mount the DM
receiver, perform the following steps (refer to the illustration on the following page):
1.
Attach the four included 06-32 x 1-1/4” standoffs (2007056) to the studs of
the included mounting bracket (2032478).
2.
Using the four included 06-32 x 3/4” slot head screws (2009211), attach the
included mounting bracket (2032478) to the electrical box.
3.
Ground the DM receiver and attach the proper cables to the rear of the unit
(refer to “Hardware Hookup” which starts on page 21 for information).
4.
Using the four included 06-32 x 1/4” Phillips head screws (2007215), attach
the DM receiver to the standoffs (2007056).
CAUTION: Excess wire that is pinched between the DM receiver and the
electrical box can short out. Ensure that all excess wire is completely inside the
electrical box and is not between the box and the DM receiver.
18  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Mounting the DM-RMC-200-S/DM-RMC-200-S2
Standoffs (4)
#06-32 x 1-1/4”
(2007056)
Screws (4)
#06-32 x 3/4”
(2009211)
2-Gang
Electrical Box
(Not Included)
Mounting
Bracket
(2032478)
Screws (4)
#06-32 x 1/4”
(2007215)
Installing the Power Pack
The included mounting bracket (2032478), which is used to attach the DM receiver
to an electrical box (not included), provides a holder for the included power pack
(2022484). To install the power pack, perform the following steps (refer to the
illustration on the following page):
1.
Slide the power pack (2022484) into the holder.
2.
Using the two included 06-32 x 1” Phillips head screws (2007250), thread
the screws through the two holes on the front of the power pack holder to
hold the power pack in place.
3.
Using the two included tie wraps (2013608), thread a tie wrap through the
hole on the top and bottom of the holder, and then fasten the tie wraps to the
power pack cable.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  19
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Installing the Power Pack
Power Pack
Holder
Tie-Wrap
Holes (2)
Screws (2)
#06-32 x 1”
(2007250)
Power Pack
(2022484)
Installation of the power pack in the holder is shown below.
Power Pack Installed in Holder of Mounting Bracket
20  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Hardware Hookup
Make the necessary connections as called out in the following illustrations. Refer to
“Network Wiring” on page 17. Apply power after all connections have been made.
Hardware Connections for the DM-RMC-200-S (Top Panel)
AUDIO OUT R, L
(SPEAKER):
Amplified Stereo
Audio Output
AUDIO OUT R, L
(LINE):
Stereo Unbalanced
Line Level
Audio Output
LAN:
10BASE-T/
100BASE-TX
Ethernet to Local
Network Device
24 V
2.0A MAX:
From Power Pack
(Included)
DM IN
MMF/SC:
From DM Switcher, Transmitter,
or Other DM Device
Hardware Connections for the DM-RMC-200-S2 (Top Panel)
AUDIO OUT R, L
(SPEAKER):
Amplified Stereo
Audio Output
AUDIO OUT R, L
(LINE):
Stereo Unbalanced
Line Level
Audio Output
LAN:
10BASE-T/
100BASE-TX
Ethernet to Local
Network Device
24 V
2.0A MAX:
From Power Pack
(Included)
DM IN
SMF/LC:
From DM Switcher, Transmitter,
or Other DM Device
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  21
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Hardware Connections for the DM-RMC-200-S/DM-RMC-200-S2 (Bottom Panel)
HDMI OUT:
Digital Video/
Audio Output
USB HID:
From USB
HID-Compliant
Device
DIG IN:
Software
Programmable
Digital Input
COM:
To RS-232
Device
IR:
To IR
Controllable
Device
Hardware Connections for the DM-RMC-200-S/DM-RMC-200-S2 (Rear Panel)
AUDIO OUT L, R
(SPEAKER):
Amplified Stereo
Audio Output
Ground
RELAY 1-2:
To
Controllable
Devices
DIG IN:
Software
Programmable
Digital Input
NOTE: Ensure that the unit is properly grounded by connecting the chassis ground
lug to an earth ground (building steel).
NOTE: Do not connect the set of speaker level audio outputs on the top panel and
the set of speaker level audio outputs on the rear panel simultaneously. Only one set
of speaker level audio outputs can be used at one time.
NOTE: For optimum performance, Crestron recommends using CresFiber 8G fiber
optic cable for the DM-RMC-200-S and CresFiber 8G SM fiber optic cable for the
DM-RMC-200-S2.
NOTE: Fiber optic cable connectors and cable ends should be protected from
contamination and scratching at all times. When cable is not connected, protect the
optical receiver on the DM receiver by using the included cap. Fiber ends should be
handled carefully and the cable should not be bent or coiled tightly.
22  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Programming Software
Have a question or comment about Crestron software?
Answers to frequently asked questions (FAQs) can be viewed in the Online Help
section of the Crestron Web site. To post a question or to view questions submitted
to Crestron’s True Blue Support, log in at www.crestron.com/onlinehelp. First-time
users must establish a user account to fully benefit from all available features.
Software Requirements for the PC
NOTE: The latest software can be downloaded from the Crestron Web site
(www.crestron.com/software).
Crestron provides an assortment of Windows-based software tools to develop a
customized system. Use Crestron SIMPL Windows to create a program to control the
DM receiver.
Programming with SIMPL Windows
SIMPL Windows is Crestron’s premier software for programming Crestron control
systems. It is organized into two separate but equally important “Managers”:
Configuration and Program.
Configuration Manager
Configuration Manager is the view where programmers “build” a Crestron control
system by selecting hardware from the Device Library.
1.
To incorporate the DM receiver into the system, drag the DM receiver from
the DigitalMedia | DM Receivers folder of the Device Library and drop it
into either of the following in System Views:

A compatible output card of a DM switcher

Directly to a card in the Ethernet slot of the control system
(used without a DM switcher)
Locating the DM-RMC-200-S/DM-RMC-200-S2 in the Device Library
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  23
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
The system tree of the control system displays the DM receiver in the
appropriate slot with a default IP ID as shown in the following illustrations.
In the first example, the DM-RMC-200-S is used with the DMCO-40 output
card in a DM-MD8X8 switcher. In the second example, the
DM-RMC-200-S is used with the C2ENET-2 card in an Ethernet slot on the
control system.
C2ENET-2 Device, Slot 8 (Using Output Card in a DM Switcher)
C2ENET-2 Device, Slot 8 (Using Ethernet Slot on Control System)
2.
If additional DM receivers are to be added, repeat step 1 for each device.
Each DM receiver is assigned a different IP ID.
3.
If necessary, double-click a device to open the “Device Settings” window
and change the IP ID as shown in the following illustration.
“Device Settings: Crestron DM-RMC-200-S” Window
24  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
NOTE: The ID code specified in the SIMPL Windows program must
match the IP ID of each unit. Refer to “Identity Code,” which starts on
page 17.
Program Manager
Program Manager is the view where programmers “program” a Crestron control
system by assigning signals to symbols.
The symbol can be viewed by double-clicking the icon or dragging it into Detail
View. Each signal in the symbol is described in the SIMPL Windows help file (F1).
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  25
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Uploading and Upgrading
Crestron recommends using the latest programming software and that each device
contains the latest firmware to take advantage of the most recently released features.
However, before attempting to upload or upgrade it is necessary to establish
communication. Once communication has been established, files (for example,
firmware) can be transferred to the device. In addition, the IP table of the device can
be configured.
Establishing Communication
Use Crestron Toolbox for communicating with the DM receiver; refer to the
Crestron Toolbox help file for details.
A PC running Crestron Toolbox communicates with the DM receiver in the
following ways:
Via DM Switcher

Via a DM switcher using TCP/IP or USB communication. TCP/IP provides
a faster method of communication than USB.

Via the LAN port of the DM receiver using TCP/IP communication. In this
scenario, the DM receiver is used in a standalone configuration (i.e., a DM
switcher is not used).
TCP/IP Communication via DM Switcher
To establish TCP/IP communication between the PC and the DM receiver via the
DM switcher:
1.
Establish communication between the PC and the DM switcher as described
in the latest version of the DigitalMedia Switchers Operations Guide
(Doc. 6755).
2.
Use the Device Discovery Tool in Crestron Toolbox to find the IP address
of the DM receiver. The tool is available in Toolbox version 1.15.143 or
later.
26  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
3.
Use the Address Book in Crestron Toolbox to create an entry for the DM
receiver using the TCP connection type, and enter the IP address of the DM
receiver.
4.
icon);
Display the “System Info” window of the DM receiver (click the
communications are confirmed when the device information is displayed.
USB Communication via DM Switcher
To establish USB communication between the PC and the DM switcher:
1.
Use the Address Book in Crestron Toolbox to create an entry using the
expected communication protocol (USB). When multiple USB devices are
connected, identify the DM switcher by entering “DM-MD8X8”,
“DM-MD16X16”, or “DM-MD32X32” in the Model textbox, the unit’s
serial number in the Serial textbox, or the unit’s hostname in the Hostname
textbox. The hostname can be found in the “System Info” window in the
section marked Ethernet; however, communications must be established in
order to see this information in the “System Info” window.
2.
icon); communications
Display the “System Info” window (click the
are confirmed when the device information is displayed.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  27
DigitalMedia 8G Fiber Receiver 200
Via LAN Port
Crestron DM-RMC-200-S/S2
TCP/IP Communication via LAN Port of DM-RMC-200-S/DM-RMC-200-S2
DM-RMC-200-S/
DM-RMC-200-S2
24V MAX
2.5A
LAN
IN
DM /SC
MMC
L
R
- +
R
- +
L
IO
AUD
OUT
PWR
DM
LINK
O
VIDE
HID
USB
SETU
P
ET
DM
DM
M
GND
TX
RX
RTS
CTS
COM
USB
IN
DIG
SG
RES
S
00ER
C-2
OLL
NTR
CO
-RM
ROO
IR
2
1 G
S
SG
HID
I OUT
HDM
PC Running
Crestron Toolbox
To establish TCP/IP communication between the PC and the DM receiver via the
LAN port of the DM receiver:
1.
Use the Device Discovery Tool in Crestron Toolbox to find the IP address
of the DM receiver. The tool is available in Toolbox version 1.15.143 or
later.
NOTE: When the DM receiver is used in a standalone configuration (i.e.,
without a DM switcher), DHCP is enabled by default. If desired, a default
IP address (192.168.1.248) can be assigned by holding down its SETUP
button while applying power. This IP address overwrites any previous
settings and remains until it is changed manually.
2.
Use the Address Book in Crestron Toolbox to create an entry for the
DM receiver using the TCP connection type, and enter the IP address of the
DM receiver.
3.
icon);
Display the “System Info” window of the DM receiver (click the
communications are confirmed when the device information is displayed.
4.
(Optional) If additional changes to TCP/IP settings are desired, do the
following:
a.
Assign an IP address, IP mask, and default router for the
DM receiver via the Crestron Toolbox (Functions | Ethernet
Addressing).
b.
Close the “System Info” window.
c.
In Crestron Toolbox, change the Address Book entry for the
DM receiver so that it uses the IP address assigned in step 4a.
d.
Display the “System Info” window of the DM receiver (click the
icon); communications are confirmed when the device information is
displayed.
28  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Firmware
Firmware files may be distributed from programmers to installers or from Crestron
to dealers. Firmware upgrades are available from the Crestron Web site as new
features are developed after product releases. For details on upgrading, refer to the
Crestron Toolbox help file.
Check the Crestron Web site to find the latest firmware. (New users may be required
to register to obtain access to certain areas of the site, including the FTP site.)
To upgrade DM receiver firmware:
1.
Do either of the following:

If the DM receiver is connected to a DM switcher, use the Device
Discovery Tool in Crestron Toolbox to find the IP address of the
switcher.

If the DM receiver is being used in a standalone configuration (not
used with a DM switcher), use the Device Discovery Tool to find
the IP address of the DM receiver.
2.
Add the IP address found in step 1 to the Address Book in Toolbox.
3.
Download the appropriate .puf file from the Crestron Web site to the PC.
4
Double-click the .puf file. The Toolbox Address Book opens.
5.
From the list in the Address Book, select the DM switcher (if the
DM receiver is connected to a switcher) or the DM receiver (if the DM
receiver is used in a standalone configuration), and then click OK.
Either of the following occurs:

If the DM switcher was selected, a DM device list is displayed that
allows an upgrade to DM devices connected to the switcher.

If the DM receiver was selected, a DM device list is displayed that
allows an upgrade to the DM receiver only.
In the DM device lists that are displayed, the checkbox of any item that
needs to be upgraded is automatically selected.
6.
Click Update.
7.
After the process is complete, click Recheck to verify the upgrade.
IP Configuration
If the DM receiver is used in a standalone configuration (i.e., not connected to a DM
switcher), use Crestron Toolbox to create the IP table entry of the DM receiver.
NOTE: If the DM receiver is connected to a DM switcher, the IP table entry of the
DM receiver is created automatically.
1.
Use the Device Discovery Tool to find the IP address of the DM receiver.
icon) and select the
Then, display the “System Info” window (click the
DM receiver entry from the Address Book.
2.
Select Functions | IP Table Setup.
3.
Add, modify or delete entries in the IP table. The DM receiver can have
only one IP table entry.
4.
A defined IP table can be saved to a file or sent to the device.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  29
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations.
If further assistance is required, please contact a Crestron customer
service representative.
DM-RMC-200-S/DM-RMC-200-S2 Troubleshooting
TROUBLE
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
PWR LED
does not
illuminate.
Device is not receiving
power.
Verify power pack connections
to the device and to the power
outlet.
PWR LED
flashes.
Memory test fails while
the device boots up.
Power cycle the device.
DM IN LED
blinks once a
second.
Device cannot establish
a link to the device
connected to the
DM IN port.
Verify cable connection to the
DM IN port.
VIDEO LED
does not
illuminate.
Device is not receiving
video signal.
Ensure proper video signal is
routed to device.
Device connected to the
HDMI OUT port has not
sent the hotplug signal.
Power on device connected to
the HDMI OUT port and ensure
that it is switched to the correct
input.
VIDEO LED is
green but
video on
connected
display is
black.
HDCP is blanking the
video output.
Verify that device connected to
HDMI output supports HDCP.
There is no
sound from
connected
speakers.
Amplifier is turned off or
EDID is not configured
properly.
In DMTool, confirm that Enable
Analog Audio Output is
selected.
Volume is turned down.
In DMTool, move the volume
slider up as necessary to
increase the volume.
(Continued on following page)
30  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Troubleshooting (Continued)
TROUBLE
Green LED on
LAN port does
not illuminate.
Loss of
functionality
due to
electrostatic
discharge.
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
LAN network cable is not
connected to the LAN port
or to the 10BASE-T/
100BASE-TX compatible
device.
Verify LAN network cable
connection to the LAN port and
to the compatible network
device.
LAN network cable is not
the proper type.
Verify that network cable
complies with EIA/TIA 568 and
the CAT5 specification.
LAN network cable is not
the proper length.
Verify that network cable is the
proper length. Cable length
must not exceed 328 feet
(100 meters).
10BASE-T/100BASE-TX
compatible device is not
receiving power.
Apply power to the network
device.
Improper grounding.
Check that all ground
connections have been made
properly.
NOTE: For more advanced diagnostics, use the DMTool in Crestron Toolbox.
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron Web site.
List of Related Reference Documents
DOCUMENT TITLE
Crestron DigitalMedia Design Guide (www.crestron.com/dmresources)
Crestron DigitalMedia Switchers Operations Guide (www.crestron.com/manuals)
Crestron e-Control Reference Guide (www.crestron.com/manuals)
Crestron IP Considerations Guide for the IT Professional
(www.crestron.com/dmresources)
Further Inquiries
To locate specific information or to resolve questions after reviewing this guide,
contact Crestron’s True Blue Support at 1-888-CRESTRON [1-888-273-7876] or
refer to the listing of Crestron worldwide offices on the Crestron Web site
(www.crestron.com/offices) for assistance within a particular geographic region.
To post a question about Crestron products, log onto the Online Help section of the
Crestron Web site (www.crestron.com/onlinehelp). First-time users must establish a
user account to fully benefit from all available features.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  31
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the DM-RMC-200-S/DM-RMC-200-S2, additional information may be made
available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation
revision.
Check the Crestron Web site periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
32  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or service without prior authorization
from Crestron. To obtain warranty service for Crestron products, contact an authorized
Crestron dealer. Only authorized Crestron dealers may contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of
the problem, name and phone number of contact person, RMA number and return address.
2.
Products may be returned for credit, exchange or service with a Crestron Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to
Crestron, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number
clearly marked on the outside of all cartons. Shipments arriving freight collect or without an
RMA number shall be subject to refusal. Crestron reserves the right in its sole and absolute
discretion to charge a 15% restocking fee plus shipping costs on any products returned with
an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by Crestron,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from Crestron,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads
and power supplies are covered for a period of one (1) year; touch screen display and overlay components
are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron
be liable for incidental or consequential damages of any kind (property or economic damages inclusive)
arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or
made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms
of this limited warranty. This warranty statement supersedes all previous warranties.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  33
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed.
PREAMBLE
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.)
You can apply it to your programs too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can
get it if you want it, that you can change the software or use pieces of it in new free programs and that you know you can do these
things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you
have. You must make sure that they too receive or can get the source code. And you must show them these terms so they know their
rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the
original, so that any problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that
any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The "Program" below refers to any such program or work, and a "work
based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the
Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is
included without limitation in the term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of
running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the
Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the
notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this
License along with the Program.
34  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for
a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and
distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does
not normally print such an announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program and
can be reasonably considered independent and separate works in themselves, then this License and its terms do not apply to those
sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work
based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend
to the entire whole and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to
exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of
physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an
offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to
control compilation and installation of the executable. However, as a special exception, the source code distributed need not include
anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel and so on) of the
operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access
to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to
copy the source along with the object code.
4. You may not copy, modify, sublicense or distribute the Program except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is void and will automatically terminate your rights under this
License. However, parties who have received copies or rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  35
DigitalMedia 8G Fiber Receiver 200
Crestron DM-RMC-200-S/S2
modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so and
all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the
original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further
restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to
this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent
license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you,
then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended
to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any
such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented
by public license practices. Many people have made generous contributions to the wide range of software distributed through that
system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Program under this License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it
and "any later version", you have the option of following the terms and conditions either of that version or of any later version
published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any
version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the
author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO
THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
36  DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2
Operations & Installation Guide – DOC. 7246B
Crestron DM-RMC-200-S/S2
DigitalMedia 8G Fiber Receiver 200
This page is intentionally left blank.
Operations & Installation Guide – DOC. 7246B
DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  37
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide – DOC. 7246B
(2031698)
10.12
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising