Sharp | UP-810F | - Inland Cash Register

- Inland Cash Register
PROGRAMMING MANUAL
N
LEAD-FREE SOLDER0 - 2
CHAPTER 1. TOUCH PANEL CALIBRATION,
MASTER RESET AND PROGRAM RESET1 1
CHAPTER 2. READING OF SRV MODE PROGRAM
2-1
<UP-820N>
CHAPTER 3. SRV MODE PROGRAMMING
(“SETTING”) 3 - 1
CHAPTER 4. SRV MODE PROGRAMMING
(“IRC SETTING”)4 - 1
CHAPTER 5. SRV MODE PROGRAMMING
(“DOWN LOAD”)5 - 1
CHAPTER 6. SRV MODE PROGRAMMING
(“SD CARD MODE”)6 - 1
<UP-810F>
<UP-820F>
CODE : 00Z UP820FUPME
LEAD-FREE SOLDER MODEL
POS TERMINAL
UP-810F
UP-820N
MODEL UP-820F
(For “U” version)
CONTENTS
LEAD-FREE SOLDER
MAJOR KEYS USED IN THE SRV MODE
CHAPTER 1. TOUCH PANEL CALIBRATION, MASTER RESET
AND PROGRAM RESET . . . . . . . . . . . . . . . . . . . . . 1 - 1
CHAPTER 2. READING OF SRV MODE PROGRAM . . . . . . . . . . 2 - 1
CHAPTER 3. SRV MODE PROGRAMMING (“SETTING”) . . . . . . 3 - 1
CHAPTER 4. SRV MODE PROGRAMMING
(“IRC SET UP”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
CHAPTER 5. SRV MODE PROGRAMMING
(“DOWN LOAD”) . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
CHAPTER 6. SRV MODE PROGRAMMING
(“SD CARD MODE”) . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
■ LEAD-FREE SOLDER
The PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The
alphabet following the LF mark shows the kind of lead-free solder.
Example:
<Solder composition code of lead-free solder>
Lead-Free
5mm
Solder composition
code (Refer to the
table at the right.)
a
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi
z
Sn-In-Ag-Bi
i
Sn-Cu-Ni
n
Sn-Ag-Sb
s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is
recomended.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to
conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause lead separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean
and file the tip with steel wool or a fine filer.
UP-810F/820N/820F (U) LEAD-FREE SOLDER
MAJOR KEYS USED IN THE SRV MODE
The following major keys are used in the SRV mode.
FUNCTION
KEY
DESRIPTION
CURSOR UP
2
Moves cursor to up (1character)
CURSOR DOWN
4
Moves cursor to down (1character)
CURSOR RIGHT
3
Moves cursor to right (1character)
CURSOR LEFT
1
Moves cursor to left (1character)
PAGE UP
PAGE DOWN
PAGE UP
Moves cursor to up (1page)
PAGE DOWN
Moves cursor to up (1page)
CLEAR
CL
CANCEL
Clear numeric entry or error message
CANCEL
ENTER
Operaation cancel & back to previous menu.
ENTER
ALL ENTER
Data entry
CA/AT
All entry terminate.
•
TOGGLE SELECT
SELECTABLE VALUE LIST
Toggles between selections
SBTL
Back to mode selection menu
KEYBOAD LAYOUT
<UP-820N>
<UP-820F/UP-810F>
@
CL
FOR
A
(
)
&
F
,
K
.
P
(
UP)
(
)
)
(
)
(
)
8
9
B
G
L
Q
4
5
6
C
H
M
R
U
W
Y
1
2
3
D
I
N
S
V
X
Z
00
E
O
T
(
(CANCEL) (ENTER)
(NEXT
(PAGE
(
[
]
)
UP)
N
(DEL)
-
-
+
"
'
?
{
<
>
(MODE)
(HOME)
(CANCEL)
(ENTER)
(PREV.
(NEXT
DOWN)
)
(
)
(
)
(BACK
(INS)
(DEL)
RECORD) RECORD)
SPACE)
RECORD) RECORD)
SPACE)
(SPACE)
(SHIFT)
_
(DC)
SBTL
(RECALL)
@
#
$
%
^
&
*
(
)
=
Q
W
E
R
T
Y
U
I
O
P
/
7
8
9
A
S
D
F
G
H
J
K
L
;
:
4
5
6
is not available for text preset key
(DC)
1
2
3
(SPACE)
(SHIFT)
0
Note: Free Key layout is available except Receipt and Journal paper
feed key.
CL
FOR
(UPDATE)
CA/AT
@
-
J
(INS)
(HOME)
RESEPT JOURNAL
(PREV.
(BACK
7
0
(PAGE
(MODE)
DOWN)
?
#
{
*
/
RECEIPT JOURNAL
(PAGE
(PAGE
Z
X
C
V
B
N
M
,
.
(SHIFT)
(SPACE)
(SPACE)
(SPACE)
(SPACE)
(SPACE)
(SPACE)
(SPACE)
(SPACE)
00 000
_
(RECALL)
(DC)
(UPDATE)
SBTL
CA/AT
Note: Free Key layout is available except Receipt and Journal paper
feed key.
UP-810F/820N/820F (U) LEAD-FREE SOLDER
CHAPTER 1. TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM
RESET
1. TOUCH PANEL CALIBRATION
[Secret key operation]
1) Calibration is started at the following cases:
This operation is used as password of MRS operation.
The following key sequence has to be entered after reset action.
If you operate wrong sequence then program reset is not performed.
• Case1: When PROGRAM reset/MRS is performed with the touch
panel pressed.
a : The key located on right upper corner.
b : The key located on left lower corner. (Flat keyboard)
b’: The key located on left lower corner. (Normal keyboard)
c : The key located on left upper corner.
d : The key located on right lower corner.
• Case2: When the calibration data held by the touch panel controller
is broken.
(However, if case 1 is performed prior to the second, calibration is
not performed.)
• a3b3c3d
• Case3: When the EEPROM on the touch panel PWB is replaced.
* If the touch panel unit is replaced for any reason such as a repair,
Key board layout
start calibration, following case 1.
2) “Calibration Mode” is displayed.
Touch cross marks by the display guidance.
a
c
2. MASTER RESET (ALL MEMORY CLEAR)
[MRS1 key & MRS2 & MRS3 key]
Position of MRS1 & MRS2 & MRS3 key is as follows.
(It is located in the upper left corner)
MRS1 key : B key
MRS2 key : A and B key
MRS3 key : B and C key
Key board layout
b
A
b'
B
C
UP-810F/820N/820F (U)
TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM RESET
1–1
d
[Master resetting]
(1) MRS-1
Master resetting 1, 2 and 3 can be accomplished by using the following
procedures.
Clears the entire memory and resumes initial values.
Procedure :
*Meaning of reset switch “ON” & “OFF” positions are as follows.
1) Set the reset switch to OFF position.
ON position: The position that CKDC becomes active state
(on the front side of the set, on the left side when facing
the reset SW: Normal status.)
2) Press and hold the MRS1 key and the reset switch move to ON
position.
3) And then, enter the secret key operation.
OFF position: The position that CKDC becomes reset state
(on the back side of the set, on the right side when facing
the reset SW: Reset status)
(2) MRS-2
Clears the entire memory and resumes initial values. (Master resetting
2 enables the layout of fixed keys in addition to master resetting 1.)
Procedure :
*Procedure before the reset switch operation.
Reset switch cover is fixed as below.
1) Set the reset switch to OFF position.
2) Press and hold the MRS2 key and the reset switch move to ON
position.
screw
3) And then, enter the secret key operation.
Program the 0 to 9 keys, 00 key, 000 key, decimal point key, CL key, X
key, SBTL key, MODE key, cursor keys, HOME key, and CANCEL key
and ENTER key and CA/AT key in this sequence.
(This means that the key first pressed is programmed as the 0 key, the
key pressed second as 1 key ---- and the last key pressed as the CA/AT
key.)
To inhibit a particular key, press the 0 key at the point when that key
should be programmed.
(3) MRS-3
reset switch cover
Master resetting 3 requires the entry of Serial No. in addition to master
resetting 2.
Procedure :
1) Set the reset switch to OFF position.
Reset switch cover can be operated after loosing screw and sliding
reset switch cover to the right
2) Press and hold the MRS3 key and the reset switch move to ON
position.
3) And then, enter the secret key operation.
After MRS3 key operation is made, serial No. entry will be prompted.
And then key layout programming will be prompted.
After complete the MRS3, following operations and programming will be
inhibited.
• GT programming.
• GT resets with Z report. (Z report can be made, but GT will not be
reset.)
• Specified memory (Serial no.) cannot be changed by All Memory
Download.
3. PROGRAM RESETTING (INITIALIZATION)
Loosing the screw (not need to be removed)
Set the reset switch to OFF position.
And the reset switch move to ON position without any key pressing.
This resetting resumes the initial program without clearing memory.
There are three possible methods to perform a master reset.
UP-810F/820N/820F (U)
TOUCH PANEL CALIBRATION, MASTER RESET AND PROGRAM RESET
1–2
CHAPTER 2. READING OF SRV MODE PROGRAM
d SAMPLE OF PROGRAM REPORTS
[How to enter SRV mode]
Operator can enter the SRV-mode by program reset operation.
1. [SYSTEM PRESET]
Please refer to “Program resetting” about program reset operation
SYSTEM PRESET
Perform the programming following the procedure shown below.
Data entry :
( Data * ) --> ENTER or CA/AT
Exit
CANCEL
:
REPORT TITLE
901#
0000
902#
0000
CONTENTS OF THE SRV-MODE
PROGRAMMING
The contents of the programming
are printed in individual formats
shown at left.
(No header is printed.)
:
* See the descriptions of respective programming procedures for job
:
code and data.
929#
0000
[Printing of program reports]
980#
0000
Select the menu for the program reports.
981#
0000
986#
0000
987#
0000
988#
0000
801#
0000
SRV-mode program full item report [#900]
(SYSTEM PRESET report) (not incl. keyboard layout)
802#
0000
803#
0000
Device config program reading report [#945]
(DEVICE CONFIG report)
804#
0000
[List of program reports]
Report name
Keyboard layout report [#950]
(KEYBOARD LAYOURT report)
Home menu display layout report [#952]
(HOME MENU DISP. report)
SRV -file programming report. [#970]
(FILE report)
The program reports can be printed in the SRV mode.
Each program report is printed on report and journal printer.
(REPORT PRINTER is assigned by #945 programming)
The program report cannot be printed on the slip printer.
Z COUNTER
TRANS. Z1
0000
TRANSACTION Z1 RESET COUNTER
TRANS. Z2
0000
TRANSACTION Z2 RESET COUNTER
CONSOLI. TRAN. Z1
0000
CONSOLI TRAN. Z1 RESET COUNTER
CONSOLI. TRAN. Z2
0000
CONSOLI TRAN. Z2 RESET COUNTER
SERVER Z1/Z2
0000
SERVER Z1/Z2 RESET COUNTER
HOURLY Z1
0000
HOULRY Z1 RESET COUNTER
PLU/UPC Z1/Z2
0000
PLU Z1/Z2 RESET COUNTER
GLU Z1
0000
GLU/PBLU Z1 RESET COUNTER
DAILY NET Z2
0000
DAILY NET Z2 RESET COUNTER
DEPARTMENT Z1
DEPARTMENT Z2
EJ Z1
0000
0000
0000
DEPARTMENT Z1 RESET COUNTER
DEPARTMENT Z2 RESET COUNTER
EJ Z1 RESET COUNTER
POSITIVE GT
GT2
$00000000000.00
GT2
$00000000000.00
GT3
$00000000000.00
TRAINING GT
NEGATIVE GT
GT3
TRAINING GT
TR
OFF
SUPERVISOR MODE
OP XZ MODE
0000
OP XZ MODE SECRET CODE
X1 OPERATE
0000
X1 OPERATION SECRET CODE
Z1 OPERATE
0000
Z1 OPERATION SECRET CODE
X2 OPERATE
0000
X2 OPERATION SECRET CODE
Z2 OPERATE
0000
Z2 OPERATION SECRET CODE
PGM1 MODE
0000
PGM1 MODE SECRET CODE
PGM2 MODE
0000
PGM2 MODE SECRET CODE
SD CARD MODE
0000
SD CARD MODE SECRET CODE
SUPERVISOR MODE
SECRET CODE
UP-810F/820N/820F (U)
READING OF SRV MODE PROGRAM
2–1
4. [KEYBOARD LAYOUT REPORT]
2. [DEVICE CONFIG]
DEVICE CONFIG
REPORT TITLE
50
BUILT-IN PRINTER
IMAGE FOOTER
NOT PRINT
JOURNAL PRINTER T#000-C#1
TM-T88 (3) / T88 (4)
EXTERNAL JOURNAL
C#1
TM-T88 (3) / T88 (4)
KEYBOARD LAYOUT
001
0 KEY
119
DEVICE NAME / TERMINAL NO.
/ CHANNEL NO.
002
1 KEY
120
KIND OF PRINTER
003
2 KEY
130
KEY NO. / KEY LABEL
/ LOCATION NO.
DEVICE NAME / CHANNEL NO.
KIND OF PRINTER
RECEIPT PRINTER
DEVICE NAME
0 NO
BILL PRINTER
T#002-C#0
YES
TM-295
00 99
REPORT PRINTER
T#000-C#0
YES
NOT PRINT
BUILT-IN
VALIDATION (VP)
T#000-C#0
TM-295
1
KP#1
T#015-C#3
YES
NOT PRINT
0/0
TM-T80
−−−
KP#2
TRAY ST / AUTO CUTTER
DEVICE NAME / TERMINAL NO.
/ CHANNEL NO.
AUTO CUTTER
5. [FILE]
PRINTER
FILE
Initial Slip feed lines. / Max lines
DEVICE NAME / TERMINAL NO.
/ CHANNEL NO.
AUTO CUTTER
LOGO TEXT
PRINTER
DEVICE NAME / TERMINAL NO.
/ CHANNEL NO.
PRINTER
TIMES OF VP
DEVICE NAME / TERMINAL NO.
/ CHANNEL NO.
AUTO CUTTER
LOGO TEXT
00073
00002-00200
CAT#1
−−−
Not assigned.
−−−
Not assigned.
DEVICE NAME / CHANNEL# / PROGRAM (*1)
/ PARITY
BAUD RATE
DEVICE NAME / CHANNEL NO.
−−−
Not assigned.
COIN DISPENSER
−−−
Not assigned.
ONLIE
C#3
DEVICE NAME / CHANNEL NO.
PREPAID CARD
−−−
Not assigned.
ONL ACCT BAL
−−−
IC CARD
C#3
POLE DISPLAY
999
Waiting time
FILE TABLE NO./NO. OF RECORDS
NO. OF BLOCKS
/NO. OF USED RECORDS
FILE TABLE NO.
/NO. OF INDEX RECORDS
- NO. OF DATA RECORDS
/NO. OF USED RECORDS(GLU)
:
PRINTER
C#3
015/00096
/00000
Not assigned.
SCALE
/00073
00096
TOP EXTRA LINE / BOTTOM EXTRA LINE
BERG (BAR)
/00050
:
*130*
Not assigned.
4800bps
00050
*002*
:
−−−
C#0 71 0DD
*001*
*093*
:
CAT#2
REPORT TITLE
:
KP#9
BCR (SCANNER)
REPORT TITLE
DEVICE NAME / LIGHT & SHADE
A7E80000
FILE MEMORY START ADDRESS
A7F00000
EMPTY MEMORY START ADDRESS
A7FFFFFF
MEMORY END ADDRESS
6. [SSP]
SSP
REPORT TITLE
SSP <Machine Name>
- 001
001
001
Not assigned.
002
001
DEVICE NAME / CHANNEL NO.
003
SSP NO.
001
:
:
* 1: PROGRAM
CHECK SUM ERROR
a: Data Bit 7Bits/8Bits
b: Stop Bit 1Bits/2Bits
3. [HOME MENU DISPLAY LAYOUT REPORT]
7. [BACKUP DATA interface]
HOME MENU DISPLAY
REPORT TITLE
HOME MENU
01
BACK_SPACE
XXX
02
DELETE
XXX
03
DIFFER_ST
MENU TITLE
SEND OK
TOUCH KEY NO/
TOUCH KEY TEXT/KEY NO.
RECEIVE OK
XXX
RA
COM.ERROR
01
DATA ERROR
20
COM.TIME-OUT
:
15
Normal termination of
a send operation
Normal termination of
a receive operation
Communication Error
XXX
Data Error
Time-out Error
UP-810F/820N/820F (U)
READING OF SRV MODE PROGRAM
2–2
CHAPTER 3. SRV MODE PROGRAMMING (“SETTING”)
[JOB LIST]
Report name
1. Device assignment (Config)
[#945]
2. SRV-mode programming
[#800 - 804 / #901 - 929 / #980 - 988]
3. Free keyboard layout
[#950]
4. Key Initial
[#951]
5. HOME Menu Display
[#952]
6. Programming of the Z report counter
[#930 - 941]
7. Programming of GT1 and GT2
[#942 - 943]
8. Programming of PGM2-mode secret codes
[#944]
9. SRV file programming
[#971]
10. Supervisor mode ON/OFF
[#985]
11. Memory initialize (Except GT memory)
[#989]
12. BACKUP Data send/receive
[#996, 998]
13. Maintenance Data Restriction by Account
[#850]
1. DEVICE ASSIGNMENT (CONFIG) [JOB #945]
CONFIGURATION FOR FOLLOWING PRINTERS AND PERIPHERALS.
TEXT
BUILT-IN PRINTER
CAT#2
JOURNAL PRINTER
PIN PAD
EXTERNAL JOURNAL
BCR (SCANNER)
RECEIPT PRINTER
BERG (BAR)
BILL PRINTER
SCALE
REPORT PRINTER
COIN DISPENSER
VALIDATION (VP)
ONLINE
KP#1
PREPAID CARD
:
ONL ACCT BAL
KP#9
IC CARD
CAT#1
POLE DISPLAY
DEVICE CONFIG - 1. BUILT IN PRINTER
DISPLAY
CONTENTS
LIGHT&SHADE
Light & shade of printing
IMAGE FOOTER
Footer Graphic LOGO print
SELECT ITEM
MRS
00-99
50
NOT PRINT
NOT PRINT
PRINT
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–1
NOTE
00= 75% for standard
50= 100% <Standard>
99= 125% for standard
DEVICE CONFIG - 2. JOURNAL PRINTER
SELECT ITEM
MRS
TERMINAL#
DISPLAY
Terminal Number
CONTENTS
0-254
0
SELF TERMINAL No.
This means local device.
1 - 254: (EXCEPT SELF TERMINAL NO.)
This means re-routed device.
Re-routin g programming is only valid for
printer.
CHANNEL#
Channel Number
0-4
0
“0” means no RS-232 channel is assigned.
PRINTER
Kind of printer
TM-T88 (3)/
T88 (4)
UP-820:
BUILT-IN
TM-U220/230
UP-810:
TM-T88 (3)
/T88 (4)
BUILT-IN
NOTE
0:
About the usage of TM-T88 (3):
POS dose not use the Graphic LOGO function
with the journal printer function.
TM-T90
DEVICE CONFIG - 3. EXTERNAL JOURNAL
DISPLAY
CONTENTS
CHANNEL#
Channel Number
PRINTER
Kind of printer
SELECT ITEM
MRS
0-4
0
TM-T88 (3)/
T88 (4)
TM-T88 (3)
/T88 (4)
NOTE
“0” means no RS-232 channel is assigned.
About the usage of TM-T88 (3):
POS dose not use the Graphic LOGO function
with the journal printer function.
TM-U220/230
TM-T90
* External Journal cannot print if program on same channel with other printer (Journal, Receipt, Report printer, etc).
DEVICE CONFIG - 4. RECEIPT PRINTER
SELECT ITEM
MRS
AUTO CUTTER
DISPLAY
Auto cutter
CONTENTS
YES
YES
TRAY ST FEED#
Tray ST feed line
0-9
NOTE
NO
0
Only receipt printer’s programming.
* Receipt prints each data at “Buffering”. Receipt printer is fixed to “Built-in printer”.
DEVICE CONFIG - 5. BILL PRINTER
DISPLAY
TERMINAL#
CONTENTS
Terminal No.
CHANNEL#
Channel No.
PRINTER
Kind of printer
SELECT ITEM
MRS
000 - 254
000
0-4
0
TM-295
(EPSON)
TM-295
(EPSON)
NOTE
000 :
Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for printer.
0:
No RS-232 channel is assigned.
TM-T88 (3) /
T88 (4)
TM-T88 (3) /
T88 (4)+LOGO
TM-U220/U230
BUILT-IN
TM-T90
AUTO CUTTER
Auto cutter
YES
INITIAL FEED#
Initial SLIP feed line number
SLIP MAX LINE
Slip print maximum line No.
NO
This item is not valid for TM-295
00 - 64
00
This item is not valid for TM-295
00 - 99
99
This item is not valid for TM-295
NO
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–2
DEVICE CONFIG - 6. REPORT PRINTER
DISPLAY
TERMINAL#
CONTENTS
Terminal No.
CHANNEL#
Channel No.
PRINTER
Kind of printer
SELECT ITEM
MRS
000 - 254
000
0-4
0
BUILT-IN
BUILT-IN
NOTE
000 :
Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for remote
printer.
0:
No RS-232 channel is assigned.
The printing method is according to “BUILT-IN
PRINTER” programming.
TM-T88 (3) /
T88 (4)
TM-U220/U230
TM-T90
AUTO CUTTER
Auto cutter
YES
YES
NO
LOGO TEXT
Logo Text Print
NOT PRINT
PRINT
PRINT
DEVICE CONFIG - 7. VALIDATION (VP)
SELECT ITEM
MRS
TERMINAL#
DISPLAY
Terminal No.
CONTENTS
000 - 254
000
CHANNEL#
Channel No.
0-4
0
PRINTER
Kind of printer
TM-295
(EPSON)
TM-295
(EPSON)
VP TIMES
No. of times of Validation print
0-9
1
SELECT ITEM
MRS
NOTE
000 :
Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for remote
printer.
0:
No RS-232 channel is assigned.
This item is valid only for TM-295.
DEVICE CONFIG - 8. KP#1 - KP#9
DISPLAY
CONTENTS
TERMINAL#
Terminal No.
000 - 254
000
CHANNEL#
Channel No.
0-4
0
PRINTER
Kind of printer
BUILT-IN
TM-T88 (3)/
T88 (4)
TM-T88 (3)/
T88 (4)
NOTE
000 :
Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for remote
printer.
0:
No RS-232 channel is assigned.
TM-U220/230
TM-T90
AUTO CUTTER
Auto cutter
YES
NO
NO
LOGO TEXT
Logo text Print
NOT PRINT
PRINT
NOT PRINT LOGO TEXT and its format is same as RECEIPT. If a printer is set as “TM-T88 (3) / 88 (4)”,
its STAMP can be printed.
TOP EXTRA LINE
Top line feed
0-9
0
BOTTOM EXTRA LINE
Bottom line feed
0-9
0
DEVICE CONFIG - 9. CAT#1 / CAT#2 / PIN PAD
Details are omitted.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–3
DEVICE CONFIG - 10. BCR (SCANNER)
DISPLAY
CONTENTS
CHANNEL#
Channel No.
BAUD RATE
Transmission speed
SELECT ITEM
MRS
0-4
0
4800 bps
4800 bps
NOTE
0:
No RS-232 channel is assigned.
9600 bps
19200 bps
DATA BITS
Data bit
7 Bits
7 Bits
8 Bits
PARITY
Parity bit
NON
ODD
EVEN
ODD
STOP BIT
Stop bit
2 Bits
1 Bit
1 Bit
* ER-A61HS1 setting : “BAUD RATE = 4800 bps” , “DATA BITS = 7Bits”, “PARITY = ODD”, “STOP BIT = 1Bit”
DEVICE CONFIG - 11. BERG (BAR) / SCALE / COIN DISPENSER / ONLINE
DISPLAY
CHANNEL#
CONTENTS
Channel No.
SELECT ITEM
MRS
0-4
0
NOTE
0:
No RS-232 channel is assigned.
DEVICE CONFIG - 12. PERPAID CARD / ONL ACCT BAL
Details are omitted.
DEVICE CONFIG - 13. IC CARD
DISPLAY
CHANNEL#
CONTENTS
SELECT ITEM
MRS
0-4
0
CONTENTS
SELECT ITEM
MRS
Waiting time until message is displayyed on POLE.
0 - 999
0
Channel No.
NOTE
0:
No RS-232 channel is assigned.
DEVICE CONFIG - 14. POLE DISPLAY
DISPLAY
WAITING TIME
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–4
NOTE
3 digits (0 to 999 seconds)
0 (No display)
2. SYSTEM PRESET (SRV-MODE PROGRAMMING)
901-D: 1. TAB setting
[JOB#801] : MRS=0000 (Not used)
1. TAB setting
[JOB#802] : MRS=0000
901-D
Flat
Normal
★
★
902-A
Flat
Normal
No
0
★
★
Yes
1
0
0
0.0
1
0.00
2
0.000
3
802-A, B : Not used (Fixed at “00”)
802-C: 1. An object of auto combo price level
1. An object of auto combo price level
Level 1 - 6
802-C
Flat
Normal
0-5
0
0
[JOB#902] : MRS = 0000 (Flat)
0040 (Normal)
802-D : Not used (Fixed at “0”)
902-A: 1. In-line system
[JOB#803] : MRS=0000
803-A: 1. Overing entry is prompted at CCD
1. Overing entry is prompted at CCD
1. In-line system
803-A
No
0
Yes
1
Flat
★
Normal
★
902-B: 1. Gift reload command to DataTran
2. REF# and AP code entry at Gift Sales in VOID
803-B, C, D : Not used (Fixed at “000”)
1. Gift reload command to DataTran
[JOB#804] : MRS=0000
802-A, B : Not used (Fixed at “00”)
802-C: 1. Taxable SUBTOTAL5 (X/Z)
2. Gross TAX5, Refund TAX5 total (X/Z)
2. REF# and AP
code entry at
Gift Sales in
VOID
AT&UM20
1. Taxable
SUBTOT
AL5
(X/Z)
Printed
Printed
Not printed
Printed
Not printed
Not printed
3. Net TAX5
total
(X/Z)
804-C
Flat
Normal
Printed
0
★
★
Not printed
1
Printed
2
Not printed
3
Printed
4
Not printed
5
Printed
6
Not printed
7
Flat
Normal
0
★
★
902-C
Flat
Normal
AT&UM4
0
★
AT&UM5
1
AT&UM4
4
AT&UM5
5
Compulsory
AT&UM8
3. Net TAX5 total (X/Z)
2. Gross
TAX5,
Refund
TAX5
total
(X/Z)
902-B
Not compulsory
2
Compulsory
4
Not compulsory
6
902-C: 1. Display format of operator display (LCD)
2. Gift Card Sales command for DataTran
1. Display format of
operator display
(LCD)
2. Gift Card Sales
command for
DataTran
GLU MODE
CHECK OUT
MODE
★
902-D : Not used (Fixed at “0”)
[JOB#903] : MRS = 6000 (Flat)
6003 (Normal)
802-D : Not used (Fixed at “0”)
903-A: 1. IR (POS data copy) baud rate (bps)
[JOB#901] : MRS=0002
1. IR (POS data copy) baud rate (bps)
901-A : Not used (Fixed at “0”)
901-B: 1. Tax system
1. Tax system
901-B
Flat
Normal
Auto tax 1-5 & Manual tax
0
★
★
Canadian tax (TYPE1 to TYPE10)
6
Canadian tax (TYPE11 VAT ON VAT)
7
2
4800
3
9600
4
19200
5
38400
6
901-C : Not used (Fixed at “0”)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–5
903-A
2400
Flat
Normal
★
★
904-C: 1. Fraction treatment at gasoline discount
903-B: 1. Symbol of scale entry
2. Printing Gift Card No. at Gift Purchase Active and Reload
1. Symbol of scale
entry
2. Printing Gift
Card No. at Gift
Purchase Active
and Reload
903-B
LB
KG
No
0
Yes
1
No
2
Yes
3
Flat
★
1. Fraction treatment at gasoline discount
904-C
Flat
Normal
★
★
904-D
Flat
Normal
0
★
★
Normal
★
Disallowed
Allowed
1
DISREGARING
2
1. TAB for gasoline
unit price
2. Gasoline function
Disable
2
2. Unit of weight for
the scale
903-C
Flat
Normal
2ID (3ID) + 2DD
0
★
★
1ID (2ID) + 3DD
1
2ID (3ID) + 2DD
2
1ID (2ID) + 3DD
3
3
Enable
1
Disable
2
Enable
3
[JOB#905] MRS=0005
905-A: 1. Taxable SUBTOTAL4 (X/Z)
2. Gross TAX4, Refund TAX4 total (X/Z)
3. Net TAX4 total (X/Z)
903-D: 1. Food stamp / Cash benefit
1. Food stamp / Cash benefit
0
904-D: 1. TAB for gasoline unit price
2. Gasoline function
903-C: 1. Entry of tare
2. Unit of weight for the scale
1. Entry of tare
ROUNDING
RAISING TO UNIT
903-D
Flat
No food stamp / Cash benefit
0
★
Tax not payable in food stamps
/ Cash benefit
1
Tax payable in food stamps
/ Cash benefit
2
Forgiveness
3
Normal
1. Taxable
SUBTOT
AL4
(X/Z)
2. Gross
TAX4,
Refund
TAX4
total
(X/Z)
Printed
★
Printed
Not printed
[JOB#904] : MRS=0000
904-A: 1. Printing of date
2. Fraction treatment at gasoline (oil) q’ty calculation
Printed
Not printed
1. Printing of date
2. Fraction treatment at gasoline (oil) q’ty
calculation
Rounding
Yes
No
Not printed
904-A
Flat
Normal
0
★
★
Raising to unit
1
Disregarding
2
Rounding
4
Raising to unit
5
Disregarding
6
1. Tax printing when
taxable
SUBTOTAL is
zero
2. Tax printing when
GST is
VAT
Yes
No
Yes
No
905-A
Flat
Normal
Printed
0
★
★
Not printed
1
Printed
2
Not printed
3
Printed
4
Not printed
5
Printed
6
Not printed
7
905-B: 1. Tax printing when taxable SUBTOTAL is zero
2. Tax printing when GST is VAT
3. Tax printing when TAX is zero
904-B: 1. Printing of the consecutive No.
2. Decimal point position of gasoline (oil) q’ty
1. Printing of the
consecutive No.
3. Net TAX4
total
(X/Z)
3. Tax printing when
TAX is
zero
905-B
Flat
Normal
Yes
0
★
★
No
1
Yes
2
No
3
Yes
4
2. Decimal point
position of gasoline (oil) q’ty
904-B
0
0
1
1
2
2
3
3
0
4
1
5
905-C
Flat
Normal
2
6
PRINTED
0
★
★
3
7
NOT PRINTED
4
Flat
★
No
Normal
★
Yes
Yes
No
No
5
Yes
6
No
7
905-C: 1. GST EXPT (X/Z)
1. GST EXPT (X/Z)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–6
906-D: 1. PLU, UPC (EAN) price look up at refund entry
2. Presetting of consecutive No.
3. Fractional quantity
905-D: 1. Tax method (canadian tax)
1. Tax method (canadian tax)
904-C
TYPE1
0
TYPE2
1
TYPE3
2
TYPE4
3
TYPE5
4
TYPE6
5
TYPE7
Flat
Normal
1. PLU,
UPC
(EAN)
price
look up
at refund
entry
2. Presetting of
consecutive No.
3. Fractional
quantity
906-D
Flat
Normal
6
No
0
★
★
TYPE8
7
Yes
Yes
TYPE9
8
907-A
Flat
Normal
Non-compulsory
0
★
★
Compulsory for an individual server (Cashier)
1
Compulsory for all server (Cashier)
2
Non-compulsory
4
Compulsory for an individual server (Cashier)
5
Compulsory for all server (Cashier)
6
TYPE10
★
★
No
9
906-A: 1. Printing of DEPT. /PLU codes
2. Entry which makes the PLU stock counter negative
1. Printing of
DEPT. /PLU
codes
No
Yes
2. Entry which
makes the PLU
stock counter
negative
Flat
Normal
Allowed
unconditionally
0
★
★
Operation allowed
despite error
message
1
Yes
Disable
Enable
Inhibited
2
Allowed
unconditionally
4
Operation allowed
despite error
message
5
Inhibited
6
Quantity
Package
3
No
4
(3-digit decimal
places)
5
No
6
7
(3-digit decimal
places)
907-A: 1. Entry of SCM (+) / (-) after registration
2. SCM input compulsory
1. Entry of
SCM (+) /
(-) after registration
Disable
2. HASH/GIFT
department setting
906-B
Flat
Normal
Disable
0
★
★
Enable
2
Disable
4
Enable
6
2. Multiplication
entry
(3-digit decimal
places)
[JOB#907] : MRS=0010
Enable
2. SCM input compulsory
SCM = Starting Cash Memory
907-B: 1. UPC (EAN) code printing on journal
2. UPC (EAN) code printing on receipt
906-C: 1. Split pricing counting
2. Multiplication entry
1. Split pricing
counting
2
Yes
No
906-B: 1. Bottle return function
2. HASH/GIFT department setting
1. Bottle return
function
No
Yes
Yes
906-A
1
Yes
No
[JOB#906] : MRS=0030
(3-digit decimal
places)
906-C
Multiplication
0
Successive
multiplication
1
Split pricing
2
FFx
(FF sequence
+ split pricing)
3
Multiplication
4
Successive
multiplication
5
Split pricing
6
FFx
(FF sequence
+ split pricing)
7
Flat
1. UPC (EAN) code
printing on journal
Normal
Yes
No
★
★
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–7
2. UPC (EAN) code
printing on
receipt
907-B
Flat
Normal
Yes
0
★
★
No
1
Yes
2
No
3
908-D: 1. Printing of X/Z report
(Excepting the individual server report)
907-C: 1. In case of all server or transaction CCD, X report before CCD
entry
2. Minus department / PLU / UPC (EAN)
1. In case of all
server or transaction CCD, X
report before
CCD entry
2. Minus department / PLU /
UPC (EAN)
Disable
Enable
907-C
Disable
0
Enable
1
Disable
2
Enable
3
Flat
Normal
★
★
2. Z1 resetting that resets GT
1. Printing of X/Z
report
(Excepting the
individual server
report)
2. Z1 resetting that
resets GT
908-D
Flat
Normal
Disable
0
★
★
Flat
Normal
★
★
Receipt & Journal
Journal only
Enable
1
Disable
4
Enable
5
907-D: 1. CCD compulsory
1. CCD compulsory
907-D
Flat
Normal
Non-compulsory
0
★
★
For individual server
1
For all server
2
[JOB#909] : MRS=2000
909-A: 1. Printing of Training GT on the X report
2. Printing of Training GT on the Z report
1. Printing of Training GT on the X
report
[JOB#908] : MRS=0000
908-A: GT print on Z report
GT1 (NET)
GT2 (+)
2. Printing of Training GT on the Z
report
909-A
Print
0
Skip
GT3 (-)
Print
Print
Skip
Print
Skip
Skip
908-A
Flat
★
Normal
Skip
1
★
Print
2
Skip
3
Print
0
Skip
1
Print
2
Skip
3
Print
4
1. Printing of data on PLU/UPC resetting
report
909-B
Flat
Normal
★
★
Print
909-B: 1. Printing of data on PLU/UPC resetting report
Skip
5
Print
0
Print
6
Skip
4
Skip
7
909-C: 1. Printing of VOID mode & MGR VOID in Z2 report
908-B: GT print on X report
GT1 (NET)
GT2 (+)
2. Printing of VOID mode & MGR VOID in Z1 report
GT3 (-)
908-B
Flat
Normal
Skip
0
★
★
Print
1
Skip
Skip
Print
Skip
Print
Print
Skip
2
Print
3
Skip
4
Print
5
Skip
6
Print
7
1. Printing of VOID
mode & MGR
VOID in Z2
report
No
Yes
909-C
Flat
Normal
Print
0
★
★
Skip
2
Print
4
Skip
6
910-A
Flat
Normal
No
0
★
★
Yes
2
Flat
Normal
★
★
Print
Skip
909-D : Not used (Fixed at “0”)
[JOB#910] : MRS=0024
908-C: 1. Addition to the hourly total in void mode
2. Resetting of consecutive number in Z1
1. Addition to the
hourly total in
void mode
2. Printing of VOID
mode & MGR
VOID in Z1
report
910-A: 1. Drawer open at server sign ON/OFF
2. Resetting of consecutive number
in Z1
908-C
Flat
Normal
No
0
★
★
Yes
1
No
4
Yes
5
1. Drawer open at server sign ON/OFF
910-B: Not used (Fixed at “0”)
910-C: 1. Server # entry system
1. Server # entry system
0
Auto sign OFF
2
910-D: Server system (Fixed at “4”)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3–8
910-C
Stay down
912-D: 1. Logo message control
[JOB#911] : MRS=0000
911-A: 1. Fraction treatment
1. Fraction treatment
Rounding
1. Logo message control
911-A
Flat
Normal
0
★
★
Raising to unit
1
Disregarding
2
911-B: 1. C/D (Check digit) check of UPC (EAN) code
1. C/D (Check digit) check of UPC (EAN)
code
911-B
No
0
Yes
4
Flat
Stamp only
1
Stamp and 3-line footer
2
6-line header instead of a stamp
3
3-line header instead of instead of a stamp
and 3-line footer
5
0
★
911-D
Flat
Normal
Format 1
0
★
★
Format 2
2
Format 3
4
Flat
Normal
★
★
0
(Logo message format)
Normal
★
912-D
3-line header instead of a stamp
1
2
5
3
911-C: Not used (Fixed at “0”)
911-D: 1. Receipt/Slip header format
1. Receipt/Slip header format
[JOB#913] : MRS=1104
913-A: 1. Content of total VP amount
1. Content of total VP amount
[JOB#912] : MRS=0061
912-A: 1. Date print format
1. Date print format
912-A
Flat
Normal
Month / Day / Year
0
★
★
Day / Month / Year
1
Year / Month / Day
1. Printing
of SBTL
2
912-B
Flat
Normal
12H
0
★
★
24H
1
Total amount
0
1
★
★
3. Printing of
MDSE ST
913-B
Flat
Normal
Disable
0
Enable
1
★
★
913-C
Flat
Normal
Yes
0
★
★
No
1
Yes
2
No
3
2. Printing
of
MDSE
ST
No
Yes
No
Yes
Yes
2. Copy
receit
function
No
Total only
Yes
3. Footer print
control
912-C
All receipts
0
On selected
function key at the
time of finalization
1
All receipts
2
On selected
function key at the
time of finalization
Normal
1. Lock error
buzzer keeps
sounding
For 2 seconds
Till error recovery
4
No
On selected
function key at the
time of finalization
5
All receipts
6
Yes
On selected
function key at the
time of finalization
7
★
★
UP-810F/820N/820F (U)
Disable
2
Enable
3
Disable
4
Enable
5
Disable
6
Enable
7
913-C: 1. Lock error buzzer keeps sounding
2. Buffered keyboard
3
All receipts
Details
Flat
Normal
Tendered amount
No
912-C: 1. After transaction receipt
2. Copy receipt function
3. Footer print control
1. After
transaction
receipt
Flat
913-B: 1. Printing of SBTL
2. Printing of MDSE ST
3. Printing of MDSE ST
912-B: 1. Time system
1. Time system
913-A
SRV MODE PROGRAMMING (“SETTING”)
3–9
2. Buffered keyboard
914-D: 1. Manual tax
2. Check / Cashing
3. Non-add No. entry
913-D: 1. Drawer closing
2. Error system
3. Key touch sound
1. Drawer
closing
2. Error system
Lock error only
Noncompulsory
Miss operation
Lock error only
Compulsory
Miss operation
3. Key
touch
soun
d
913-D
Yes
0
Flat
1. Manual
tax
Normal
Yes
Yes
No
Yes
No
No
Enable
No
1
Yes
2
No
3
Yes
4
No
5
Yes
6
No
7
Enable
Enable
Disable
★
★
Disable
Enable
3. Tax delete
0
★
★
1
Enable
2
Disable
3
Enable
4
Disable
5
Enable
6
Disable
7
914-A
Flat
Normal
915-A
Flat
Normal
“ ”
0
★
★
“*”
1
“$”
2
915-B: 1. PO system
1. PO system
Inhibit
0
Enable
1
Inhibit
2
Enable
3
Inhibit
4
Enable
5
Inhibit
6
Enable
7
1. No-sale after non-add code entry
★
915-B
Flat
Normal
Mixed entry
0
★
★
Cash only entry
1
★
915-C: 1. No. of times of ST(-) or ST(%) entry within one transaction
2. RA system
1. No. of times of
ST(-) or ST(%)
entry within one
transaction
Any No. of times
914-B
Disable
0
Enable
1
Flat
Normal
★
★
2. RA system
2. Non-add code
entry at the
beginning of a
transaction operation
913-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
915-C
Flat
Normal
★
★
Mixed entry
4
Cash only entry
5
Mixed entry
6
Cash only entry
7
915-D: Not used (Fixed at “0”)
914-C: 1. Void mode
2. Non-add code entry at the beginning of a transaction operation
Disable
Normal
Disable
1. Amount symbol
Once
Enable
Flat
915-A: 1. Amount symbol
914-B: 1. No-sale after non-add code entry
1. Void mode
914-D
[JOB#915] : MRS=0040
914-A: 1. Receipting at the time of no sale
2. [NS] key separation from [CA/AT] key for no sale function
3. Tax delete
1. Receipting at
the time
of no
sale
3. Non-add
No. entry
Disable
[JOB#914] : MRS=1100
2. [NS] key
separation from
[CA/AT]
key for
no sale
function
2. Check /
Cashing
Flat
★
[JOB#916] : MRS=1400
916-A: 1. Action to be taken when text and amount overlaps each other
in a REG-mode entry
Normal
1. Action to be taken when text and
amount overlaps each other in a REGmode entry
916-A
Over-write
0
2 line print
1
★
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 10
Flat
Normal
★
★
916-B: 1. Finalization by charge (credit) when ST t 0
2. Food stamp/Cash benefit subtotal entry before Food stamp/
Cash benefit tender
1. Finalization by
charge (credit)
when ST t 0
2. Food stamp/
Cash benefit
subtotal entry
before Food
stamp/Cash
benefit tender
Inhibit
Always
916-B
Non-compulsory
0
Compulsory
1
Non-compulsory
4
Compulsory
5
Flat
[JOB#917] : MRS=0000
917-A: 1. Printing of taxable 1 subtotal on X/Z report
2. Printing of gross tax 1 and refund tax 1 totals on X/Z report
3. Printing of net tax 1 total on X/Z report
Normal
★
1. Printing
of taxable
1 subtotal
on X/Z
report
★
Print
Print
916-C: 1. Merchandise subtotal go negative
2. Subtotal entry before tender
3. Subtotal entry before direct non-tendering finalization
1. Merchan- 2. Subtotal
dise subentry
total go
before
negative
tender
Noncompulsory
Enable
Compulsory
Noncompulsory
Disable
Compulsory
Skip
Print
3. Subtotal
entry
before
direct
non-tendering
finalization
916-C
Noncompulsory
0
Compulsory
1
Noncompulsory
2
Compulsory
3
Noncompulsory
4
Compulsory
5
Noncompulsory
6
Compulsory
7
Skip
Flat
★
Skip
Normal
2. Net sales
subtotal
(NET1)
printing
on X/Z
report
Print
Print
Skip
Print
Skip
Skip
3. Check
change
total
printing
on X/Z
report
★
1. Printing
of taxable
2 subtotal
on X/Z
report
2. Printing
of gross
tax 2 and
refund
tax 2
totals on
X/Z
report
Print
Print
Skip
Print
Skip
Skip
916-D
Flat
Normal
Print
0
★
★
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
917-A
Flat
Normal
Print
0
★
★
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
3. Printing
of net tax
2 total on
X/Z repor
917-B
Flat
Normal
Print
0
★
★
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
917-C: 1. Printing of taxable 3 subtotal on X/Z report
2. Printing of gross tax 3 and refund tax 3 totals on X/Z report
3. Printing of net tax 3 total on X/Z report
1. Printing
of taxable
3 subtotal
on X/Z
report
2. Printing
of gross
tax 3 and
refund
tax 3
totals on
X/Z
report
Print
Print
Skip
Print
Skip
Skip
UP-810F/820N/820F (U)
3. Printing
of net tax
1 total on
X/Z
report
917-B: 1. Printing of taxable 2 subtotal on X/Z report
2. Printing of gross tax 2 and refund tax 2 totals on X/Z report
3. Printing of net tax 2 total on X/Z report
916-D: 1. Coupon PLU printing on X/Z report
2. Net sales subtotal (NET1) printing on X/Z report
3. Check change total printing on X/Z report
1. Coupon
PLU
printing
on X/Z
report
2. Printing
of gross
tax 1 and
refund
tax 1
totals on
X/Z
report
SRV MODE PROGRAMMING (“SETTING”)
3 – 11
3. Printing
of net tax
3 total on
X/Z
report
917-C
Flat
Normal
Print
0
★
★
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
917-D: 1. Printing of total tax on X/Z report
2. Printing of gross manual tax and refund manual tax totals on
X/Z report
918-C: 1. Kitchen printer consolidation
2. Printing the UPC/DEPT/PLU text on KP in double size character
3. Printing of net manual tax total on X/Z report
1. Printing
of total
tax on X/
Z report
2. Printing
of gross
manual
tax and
refund
manual
tax totals
on X/Z
report
Print
Print
Skip
Print
Skip
Skip
3. Printing
of net
manual
tax total
on X/Z
repor
1. Kitchen printer
consolidation
917-D
Flat
2. Printing the
UPC/DEPT/PLU
text on KP in
double size character
918-C
No
0
Yes
1
No
2
Yes
3
Normal
No
Yes
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
★
1. Tip paid
includes
cash tip
2. Clearing
of tip
totalizer
at clerk
Z1 report
No
Yes
918-A: 1. Printing of text for associated PLU in combo meal
Yes
2. Direct non-tendering finalization after previous tender entry
3. Output of combo meal to KP
No
1. Printing
of text for
associated PLU
in combo
meal
Disable
Print
Enable
Disable
Skip
Enable
3. Output
of
combo
meal to
KP
No
Yes
918-A
Flat
Normal
Yes
★
3. Printing
of tip
totalizer
on the
clerk
report
918-D
Flat
Normal
No
0
Yes
1
No
2
Yes
3
★
★
No
4
Yes
5
No
6
Yes
7
Flat
Normal
★
★
919-A: 1. GLU/PBLU system
By associated PLU
0
Combo
meal’s KP
1
By associated PLU
2
Combo
meal’s KP
3
2. GLU/PBLU code entry at reorder
(When #919:B-1 is 0 (auto generation))
★
1. GLU/PBLU system
★
PB look-up system
By associated PLU
4
Combo
meal’s KP
5
By associated PLU
6
Combo
meal’s KP
7
Guest look-up
system
2. Fractional
entries for nonscalable UPC/
PLU/DEPT.
Enable
1. Checking of service# on guest
check when a
reorder is made
Yes
918-B
Flat
Normal
No
0
Disable
1
Enable
2
Disable
3
2. GLU/PBLU code
entry at reorder
(When #919:B-1
is 0 (auto generation))
919-A
Non-compulsory
2
Compulsory
3
Non-compulsory
4
Compulsory
5
919-B: 1. Checking of service# on guest check when a reorder is made
2. Guest check number
2. Fractional entries for non-scalable UPC/PLU/DEPT.
No
★
[JOB#919] : MRS=5100
918-B: 1. Red color printing on KP when PLU’s unit price is zero
1. Red color printing on KP when
PLU’s unit price
is zero
Normal
918-D: 1. Tip paid includes cash tip
2. Clearing of tip totalizer at clerk Z1 report
3. Printing of tip totalizer on the clerk report
[JOB#918] : MRS=2233
2. Direct
non-tendering
finalization after
previous
tender
entry
Flat
★
★
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 12
2. Guest check
number
919-B
Auto generation
0
Manual
1
Auto generation
4
Manual
5
Flat
Normal
★
★
919-C: 1. PB entry
[JOB#921] : MRS=0000
2. Amount printing when PLU unit price is zero
1. PB entry
2. Amount printing
when PLU unit
price is zero
919-C
No
0
Yes
1
No
2
Yes
3
Non-compulsory
Compulsory
921-A: 1. Convert UPC-E code to UPC-A code
Flat
★
1. Convert UPC-E code to UPC-A code
Normal
★
921-A
Flat
Normal
No
0
★
★
Yes
4
921-B: 1. GLU system
1. GLU system
919-D: 1. Conversion SBTL printing of native SBTL
921-B
Flat
Normal
Centralized
0
★
★
Individual
4
2. Foreign currency format
921-C: 1. BILL printing method: The action after printing Bill.
1. Conversion
SBTL printing of
native SBTL
Yes
No
2. Foreign currency format
919-D
Flat
Normal
1. BILL printing method: The action after
printing Bill.
921-C
Flat
Normal
★
★
The item data is deleted and each bill continue to print in the previous bill.
0
★
★
The item data is not deleted and each bill
prints all item.
1
Not
0
Omit digits lower
than TAB position
1
Not
4
Omit digits lower
than TAB position
5
921-D: 1. TIP PAID is automatically executed when TIP is remained at
Ind. Server Resetting.
1. TIP PAID is automatically executed
when TIP is remained at Ind. Server
Resetting.
[JOB#920] : MRS=2040
920-A: 1. Back-up master function
1. Back-up master function
920-A
Flat
Normal
Not exist
2
★
★
Exist
3
920-B
Flat
Normal
Disable
0
★
★
Enable
4
Normal
No
0
★
★
Yes
4
2. PGM-mode programming at the satellite
922-A: Not used (Fixed at “0”)
922-B: 1. Using new coin dispenser which can treat $1 coins
1. Using new coin dispenser which can
treat $1 coins
920-C: 1. Automatic download machines in an inline system at UPC
(EAN) programming and UPC (EAN) delete.
1. Automatic download machines in
an inline system
at UPC (EAN)
programming
and UPC (EAN)
delete.
Flat
[JOB#922]: MRS=0000
920-B: 1. System report and down-load job is executed in the back-up
master.
1. System report and down-load job is
executed in the back-up master.
921-D
922-B
Flat
Normal
Yes
0
★
★
No
1
922-C, D: Not used (Fixed at “00”)
[JOB#923] : MRS=0010
923-A, B: 1. The record number for REQUEST of T-LOG POLLING
(x100) for satellite
2. PGM-mode programming at the
satellite
Disable
Yes
No
920-C
Flat
Normal
Enable
1
4
Enable
5
★
Stand-alone machine
Flat
Normal
0000 ~ 9900
00-99
00
00
When input 10 to AB, the T-log records exceed 1, 000 records. By that
the satellite request T-LOG POLLING to master.
★
Note:
In case of 00, the satellite request T-LOG POLLING to master at each
transaction. but master dose not request T-LOG POLLING to MWS
(Manager Work Station).
920-D: 1. Status of the register
1. Status of the register
923-AB
Ex:
0
Disable
1. The record number for REQUEST of
T-LOG POLLING
(x100) for satellite
920-D
Flat
Normal
0
★
★
920-C: 1. T-log function
Satellite
1
Master
2
No
0
Back up master
3
Yes
1
1. T-log function
UP-810F/820N/820F (U)
923-C
SRV MODE PROGRAMMING (“SETTING”)
3 – 13
Flat
Normal
★
★
925-D: 1. Resetting is allowed when the server is remained sign on
2. Resetting in the open store state
923-D: 1. Polling cycle (second)
1. Polling cycle (second)
0 ~ 9 Sec.
923-D
Flat
Normal
0-9
0
0
1. Resetting is
allowed when
the server is
remained sign
on
Ex:
When input D = 5, the master waits 5 sec., and then the master starts TLOG POLLING to next machine.
2. Resetting in the
open store state
925-C
Disable
0
No
Enable
1
2
Enable
3
★
★
2. Printing “PAST
VOID DATA” on
KP
926-A
Flat
Normal
Both last-void-data
and voided item
aren’t printed
0
★
★
926-B
Flat
Normal
★
★
Yes
924-D: 1. Locking after daily net resetting
2. Locking after transaction resetting
1. Locking after
daily net resetting
2. Locking after
transaction
resetting
Yes
No
Normal
Disable
[JOB#924] : MRS=1433
924-A, B, C: Not used (Fixed at “143”)
Flat
[JOB#926] : MRS=0000
924-D
Yes
0
No
1
Yes
2
No
3
Flat
925-D: 1. Printing “LAST VOID DATA” on KP
2. Printing “PAST VOID DATA” on KP
Normal
1. Printing “LAST
VOID DATA” on
KP
★
Both last-void-data
and voided item
aren’t printed
★
Both are printed
1
Both last-void-data
and voided item
aren’t printed
2
Both are printed
3
* Setting of lock timing for REG-mode entries after individual periodic
total resetting.
Both are printed
[JOB#925] : MRS=0303
925-A:Not used (Fixed at “0”)
926-B: 1. Sending “REFUND DATA” on KP.
925-B: 1. Various individual resetting.
1. Various individual resetting
Disable
Enable
925-B
Flat
1. Sending “REFUND DATA” on KP
Normal
0
Yes
0
3
No
2
★
★
* Individual resetting Enable/Disable: The master alone can be made
capable of resetting by selecting “Disable”
925-C: 1. Report printing when consolidation daily and periodic total
transaction reading or resetting is taken
1. Report printing when consolidation
daily and periodic total transaction
reading or resetting is taken
925-C
Flat
Normal
Printing of both i.e. reports on individual
machines and consolidation report on the
entire system
0
★
★
Printing of consolidation report on the
entire system
1
Printing of report on individual register
2
926-C: 1. Open store/Close store at stand alone POS with online
2. Send AT command string with “Open Store” job
3. Send AT command string with “Close Store” job
1. Open
store/
Close
store at
stand
alone
POS with
online
3. Send AT
2. Send AT
comcommand
mand
string
string
with
with
“Close
“Open
Store” job
Store” job
No
No
Yes
* Type of printing of daily total and periodic total transaction X/Z
reports: The following of three types are available:
No
Yes
a) Printing of only X/Z reports on individual machines
Yes
b) Printing of a consolidation X/Y report only
c) Printing of X/Z reports on individual machines, followed by the
printing of a consolidation X/Y report.
Flat
Normal
★
★
Flat
Normal
★
★
No
0
Yes
1
No
2
Yes
3
No
4
Yes
5
No
6
Yes
7
926-D: 1. Reverse ONLINE channel in closed store
1. Reverse ONLINE channel in closed
store
UP-810F/820N/820F (U)
926-C
No
0
Yes
4
SRV MODE PROGRAMMING (“SETTING”)
3 – 14
926-C
929-C: 1. Markdown system and entry system
[JOB#927] : MRS=0000 (Not used)
2. Registration when closed file is full
[JOB#928] : MRS=0060
1. Markdown system and entry
system
928-A: 1. Printing of slip logo text
1. Printing of slip logo text
928-A
Flat
Normal
No
0
★
★
Yes (According to media programming)
1
2. Header line on
bill paper when a
reorder is made
printed
Check only
Check & Charge
928-B
Flat
Normal
Printed
0
★
★
Skip
1
Printed
2
Skip
3
928-C
Yes
0
No
2
Yes
4
No
6
No
Inhibited
0
★
★
Continued
1
Inhibited
2
Continued
3
Inhibited
6
Continued
7
Cursor markdown
system and BOGO
entry system
929-D: 1. Selection of method of seal character of TAX contents in BILL
1. Selection of
method of seal
character of TAX
contents in BILL
Flat
2. Taxable status of
PLU/UPC (EAN)
which is set of
“Non-Taxable”
980-D
Flat
Normal
According to its
associated Dept.
0
★
★
980-B
Flat
Normal
No
0
★
★
Yes
1
Flat
Normal
The total of tax
amount is printed
Normal
The tax amount of
every TAX is printed
in detail
★
★
Non-Taxable
2
According to its
associated Dept.
4
Non-Taxable
6
[JOB#980] : MRS=0000
980-A: Not used (Fixed at “0”)
928-D: 1. Printing of PB/Service on bill at re-order
2. Compulsory Bill print system
1. Printing of PB/
Service on bill at
re-order
Normal
2. Taxable status of PLU/UPC (EAN) which is set of “Non-Taxable”
2. Printing of text
for associated
PLU in “COMBO
MEAL” on bill.
Yes
Flat
Cursor markdown
system and normal
entry system
928-C: 1. Printing of PLU on bill when it is 0
2. Printing of text for associated PLU in “COMBO MEAL” on bill.
1. Printing of PLU
on bill when it is 0
980-D
Normal markdown
system and normal
entry system
928-B: 1. VP message printing on slip
2. Header line on bill paper when a reorder is made printed
1. VP message
printing on slip
2. Registration
when closed file
is full
980-B: 1. Hash/Gift department effect hourly sales total
1. Hash/Gift department effect hourly
sales total
2. Compulsory Bill
print system
928-D
Flat
Normal
According to each
media’s preset
0
★
★
Compulsory for
every entry
1
980-C, D: Not used (Fixed at “00”)
Compulsory for PB
2
[JOB#981] - [JOB#985] : Reserved
According to each
media’s preset
4
Compulsory for
every entry
5
Compulsory for PB
6
Yes
No
[JOB#986] : MRS = 2000
986-A: 1. CAT2
1. CAT2
The bill printing at SERV and final in GLU system acts on each media’s
preset.
986-A
SECL CAT
0
DATA TRAN
2
★
★
986-B: Not used (Fixed at “0”)
[JOB#929] : MRS=0000
986-C: 1. Sub-total void in customer entry
929-A: 1. KP print format when finalizing
1. KP print format when finalizing
929-A
Simple
0
Detail
1
Flat
★
★
986-C
Flat
Normal
Enable
0
★
★
Disable (Manager only enable)
4
986-D: 1. PLU/UPC printing on receipt when it is zero
929-B: 1. Server, transaction resetting allowed with open GLU
1. Server, transaction resetting allowed
with open GLU
1. Sub-total void in customer entry
Normal
929-B
Flat
Normal
1. PLU/UPC printing on receipt when it is
zero
986-D
Flat
Normal
No
0
★
★
Yes
0
★
★
Yes
1
No
1
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 15
code is assigned, and will be direct PLU keys if PLU code is assigned
in the PGM2 mode.
[JOB#987] : MRS = 0000
987-A: Not used (Fixed at “0”)
MRS : STANDARD KEY LAYOUT
987-B: 1. Age limit function to be override in MGR mode
[FUNCTION KEY GROUP LIST]
1. Age limit function to be override in
MGR mode
987-C
Flat
Normal
Disable
0
★
★
Enable
2
No.
FUNCTION
1
ALL FUNC. KEY
2
LEVEL#
3
PRICE SFT#
4
TAX1SF
[JOB#988] : MRS = 0000
5
GD1SFT
988-A: 1. Customer code entry finalized by
2. Payment by charge1 over customer charge amount
6
GDSC%1
7
%1
8
(-)1
987-C, D: Not used (Fixed at “00”)
1. Customer code
entry finalized by
2. Payment by
charge1 over
customer charge
amount
988-A
Enable
0
Charge1 only
Any payment
Flat
★
Normal
★
9
AUTO
10
CASH2
11
CHECK
CHARGE1
Disable
1
12
Enable
2
13
CONV1
3
14
RA
15
PO
16
CA/CHK1
17
EATIN1
18
MESSAGE1
19
PLU MENU 1
20
MACRO1
21
CAP. 1
22
FUNC MENU 01
23
GAS1 ST
Disable
988-B: 1. Control characters (ex. double character) (From code: 0x00
to 0x1F, 0xFE, 0xFF) when EJ data is recorded in the SD
CARD.
1. Control characters (ex. double character) (From code: 0x00 to 0x1F, 0xFE,
0xFF) when EJ data is recorded in the
SD CARD.
988-B
Not space character
0
Space character (code: 0x20)
2
Flat
★
Normal
★
988-C, D: Not used (Fixed at “00”)
If “ALL FUNC. KEY” is selected, the cursor jumps to key No. 28
“BKSPC”.
3. FREE KEYBOARD LAYOUT
(FUNCTION KEY LIST) [#950]
About jump key number of other functions refer to below function key
list.
This job can be set the keyboard layout (except for dept. keys and direct
PLU keys) and REG MODE HOME screen (15 keys).
[FUNCTION KEY LIST]
12345678901234567890123456789012345678901234
Information Area-2 (1x21)
1
KEY
KEY
KEY
(2x6Char.)
(2x6Char.)
(2x6Char.)
2
3
KEY
(2x6Char.)
4
5
Main Display Area (8x20)
6
7
8
9
10 T A X
11
12
0 . 00
SBT L
0 . 00
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
KEY
(2x6Char.)
Information Area-1 (1x44)
Numeric key data Area (1x20)
Common Status Area (1x17)
TIME (1x7)
MRS : STANDARD KEY LAYOUT
If (X) key is pushed in case of setting the keyboard layout, that key is
inhibited.
• FREE KEY LAYOUT (FOR DEPT. KEYS AND DIRECT PLU KEYS)
Programming of keys to be Dept. keys or direct PLU keys on the keyboard.
Key No. is assigned to each key which is supposed to be Dept. key or
direct PLU key by depressing the key after entering the Key No..
Those keys programmed by this Job No. will be Dept. keys if Dept.
UP-810F/820N/820F (U)
Jump
to
key
No.
FUNCTION
DISPLAY KEY
999
INHIBIT
INHIBIT
1
0 KEY
2
3
TOUCH KEY
Text
Func.
Menu
0 KEY
0
No
1 KEY
1 KEY
1
No
2 KEY
2 KEY
2
No
4
3 KEY
3 KEY
3
No
5
4 KEY
4 KEY
4
No
6
5 KEY
5 KEY
5
No
7
6 KEY
6 KEY
6
No
8
7 KEY
7 KEY
7
No
9
8 KEY
8 KEY
8
No
10
9 KEY
9 KEY
9
No
11
00 KEY
00 KEY
00
No
12
000 KEY
000 KEY
000
No
13
Decimal point
. KEY
.
No
14
Clear
CL
CLEAR
No
SRV MODE PROGRAMMING (“SETTING”)
3 – 16
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
15
X
X
X/QTY
No
58
BILL TRANSFER
B. T.
B. T.
Yes
16
Sub total
SUB TOTAL
SUB_TOTAL
Yes
59
FS TEND
FSTEND
FSTEND
Yes
17
Mode
MODE
MODE
Yes
60
FS TEND by EBT
FSTEND EBT
FSTENDEBT
Yes
18
CURSOR UP
UP
b
No
61
CASH BENEFIT by
EBT
CASH BENEFIT
CASH BNF
Yes
62
FS/CASH BENEFIT SUBTOTAL
FS/CBNF ST
FS/CBNF ST
Yes
63
SERVER NUMBER
SERVER#
SRV#
Yes
64
REMOTE
PRINTER SEND
RP SND
RP SND
Yes
19
CURSOR DOWN
DOWN
c
No
20
CURSOR LEFT
LEFT
0MORE
No
21
CURSOR RIGHT
RIGHT
MORE3
No
22
HOME
HOME
HOME
Yes
23
CANCEL
CANCEL
CANCEL
No
24
ENTER
ENTER
ENTER
No
65
GRATUITY
GRATUITY
GRA_TUITY
Yes
25
TOTAL
TL
CASH_TOTAL
Yes
66
OPEN TARE
OPEN TARE
OPEN_TARE
Yes
26
PAGE UP
PAGE UP
PAGE_UP
No
67
BALANCE
BALANCE
BAL
Yes
27
PAGE DOWN
PAGE DOWN
PAGE_DOWN
No
68
REPEAT
REPEAT
REPEAT
Yes
28
BACK SPACE
BACK SPACE
BACK_SPACE
No
69
AMOUNT
AMOUNT
AMOUNT
Yes
29
DELETE
DELETE
DELETE
No
70
DEPT#
DEPT#
BEIGE
Yes
30
MERCHANDISE
SUB-TOTAL
MDS ST
MDS ST
Yes
71
INQUIRE
INQ
INQ
Yes
72
PRICE CHANGE
TRAY SUB-TOTAL
TRY ST
TRY ST
Yes
PRICE
CHANGE
PRICE
_CHANGE
Yes
31
32
GASOLINE SALES
SUB-TOTAL
GAS ST
GAS ST
Yes
73
CUSTOMER
CUSTOMER
CUST
Yes
33
NON ADD/TIME
#/TM
#_TIME
Yes
34
NO SALE
NO SALE
NS
Yes
35
SCALE
SCALE
SCALE
Yes
36
PLU/UPC
PLU/UPC
PLU_UPC
37
FS/CASH
BENEFIT SHIFT
38
VALIDATION
PRINT
PRNT
PRNT
Yes
39
BILL
BILL
BILL
Yes
40
COPY/AFTER
TRANSACTION
RECEIPT
RCPT
RCPT
Yes
41
G. C. COPY
GCCOPY
GCCOPY
Yes
42
CHARGE TIP
CHARGE TIP
CHARGE_TIP
Yes
FS/CBN SHIFT FS/CBN SHIFT
Yes
74
BIRTHDAY
BIRTH
BIRTH
Yes
75
TRANSOUT
TRANS OUT
TRANS_OUT
Yes
76
TRANS IN
TANS IN
TRANS_IN
Yes
77
SEAT#
SEAT#
SEAT#
Yes
78
INDIVIDUAL
PAYMENT
I.PAY
I.PAY
Yes
79
REFUND TYPE OF
SALE
RF.SAL
RF.SAL
Yes
80
RECEIPT ON/OFF
RCPT ON/OFF
RCP_ON/OFF
Yes
Yes
43
CASH TIP
CASH TIP
CASH_TIP
Yes
44
TIP PAID
TIP PAID
TIP_PAID
Yes
45
LAST VOID
VOID
VOID
Yes
46
INDIRECT VOID
I. VOID
I. VOID
Yes
47
SUB-TOTAL VOID
ST VD
ST VD
Yes
48
REFUND
REFUND
REFUND
Yes
49
RETURN
RETURN
RETURN
Yes
50
TAX
TAX
TAX
Yes
51
COVER COUNT
COVER
COUNT
COVER
_COUNT
Yes
52
GLU/PBLU
PBAL
PBAL
Yes
53
NEW CHICK
N. C.
N. C.
Yes
54
SERVICE
SERVICE
SRVC
Yes
55
FINAL
FINAL
FINAL
Yes
56
DEPOSIT
DEPOSIT
DEPO
Yes
57
DEPOSIT
REFUND
DEPOSIT RF
DEPO
_REFOUND
Yes
UP-810F/820N/820F (U)
81
Bill Separate
B.S.
B.S.
Yes
82
WASTE MODE
WASTE
WASTE
Yes
83
CONDIMENT
NEXT
C NEXT
C NEXT
Yes
84
NEXT$
NEXT$
NEXT$
Yes
85
Edit Tip
EDIT TIP
EDIT_TIP
Yes
86
Repeat Round
REPEAT
ROUND
REPEAT
_ROUND
Yes
87
GLU Recall
GLU RECALL
GLU_RECALL
Yes
88
UPSIZE
UPSIZE
UPSIZE
Yes
89
GIFT CARD
BALANCE
GC BAL
GC BAL
Yes
90
MANAGER
NUMBER
MGR#
MGR#
Yes
91
HOLD/RECALL
HOLD/RECALL
HOLD
_RECALL
Yes
92
LEVEL SHIFT#
LEVEL#
LEVEL#
Yes
93
Level1
L1
L1
Yes
94
Level2
L2
L2
Yes
95
Level3
L3
L3
Yes
96
Level4
L4
L4
Yes
97
Level5
L5
L5
Yes
98
PRICE SHIFT#
PRICE SFT#
PRICE_SHIFT#
Yes
SRV MODE PROGRAMMING (“SETTING”)
3 – 17
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
99
Price1
PRICE SFT1
P1
Yes
143
AUTO10
AUTO10
AUTO10
Yes
100
Price2
PRICE SFT2
P2
Yes
144
AUTO11
AUTO11
AUTO11
Yes
101
Price3
PRICE SFT3
P3
Yes
145
AUTO12
AUTO12
AUTO12
Yes
102
Price4
PRICE SFT4
P4
Yes
146
AUTO13
AUTO13
AUTO13
Yes
103
Price5
PRICE SFT5
P5
Yes
147
AUTO14
AUTO14
AUTO14
Yes
104
Price6
PRICE SFT6
P6
Yes
148
AUTO15
AUTO15
AUTO15
Yes
105
TAX1 SHIFT
TAX1SF
TAX1SF
Yes
149
AUTO16
AUTO16
AUTO16
Yes
106
TAX2 SHIFT
TAX2SF
TAX2SF
Yes
150
AUTO17
AUTO17
AUTO17
Yes
107
TAX3 SHIFT
TAX3SF
TAX3SF
Yes
151
AUTO18
AUTO18
AUTO18
Yes
108
TAX4 SHIFT
TAX4SF
TAX4SF
Yes
152
AUTO19
AUTO19
AUTO19
Yes
109
TAX5 SHIFT
TAX5SF
TAX5SF
Yes
153
AUTO20
AUTO20
AUTO20
Yes
110
GROUP
DISCONT1 SHIFT
GD1SFT
GD1SFT
Yes
154
AUTO21
AUTO21
AUTO21
Yes
155
AUTO22
AUTO22
AUTO22
Yes
111
GROUP
DISCONT2 SHIFT
GD2SFT
GD2SFT
Yes
156
AUTO23
AUTO23
AUTO23
Yes
112
GROUP
DISCONT3 SHIFT
GD3SFT
GD3SFT
Yes
157
AUTO24
AUTO24
AUTO24
Yes
158
AUTO25
AUTO25
AUTO25
Yes
GROUP
DISCOUNT% 1
GDSC%1
159
AUTO26
AUTO26
AUTO26
Yes
160
AUTO27
AUTO27
AUTO27
Yes
GROUP
DISCOUNT% 2
GDSC%2
161
AUTO28
AUTO28
AUTO28
Yes
162
AUTO29
AUTO29
AUTO29
Yes
113
114
GROUP
_DISC1
Yes
GROUP
_DISC2
Yes
115
GROUP
DISCOUNT% 3
GDSC%3
GROUP
_DISC3
Yes
163
AUTO30
AUTO30
AUTO30
Yes
116
%1
%1
%1
Yes
164
AUTO31
AUTO31
AUTO31
Yes
117
%2
%2
%2
Yes
165
AUTO32
AUTO32
AUTO32
Yes
118
%3
%3
%3
Yes
166
AUTO33
AUTO33
AUTO33
Yes
119
%4
%4
%4
Yes
167
AUTO34
AUTO34
AUTO34
Yes
120
%5
%5
%5
Yes
168
AUTO35
AUTO35
AUTO35
Yes
121
%6
%6
%6
Yes
169
AUTO36
AUTO36
AUTO36
Yes
122
%7
%7
%7
Yes
170
AUTO37
AUTO37
AUTO37
Yes
123
%8
%8
%8
Yes
171
AUTO38
AUTO38
AUTO38
Yes
124
%9
%9
%9
Yes
172
AUTO39
AUTO39
AUTO39
Yes
125
(-)1
(-)1
(-)1
Yes
173
AUTO40
AUTO40
AUTO40
Yes
126
(-)2
(-)2
(-)2
Yes
174
AUTO41
AUTO41
AUTO41
Yes
127
(-)3
(-)3
(-)3
Yes
175
AUTO42
AUTO42
AUTO42
Yes
128
(-)4
(-)4
(-)4
Yes
176
AUTO43
AUTO43
AUTO43
Yes
129
(-)5
(-)5
(-)5
Yes
177
AUTO44
AUTO44
AUTO44
Yes
130
(-)6
(-)6
(-)6
Yes
178
AUTO45
AUTO45
AUTO45
Yes
131
(-)7
(-)7
(-)7
Yes
179
AUTO46
AUTO46
AUTO46
Yes
132
(-)8
(-)8
(-)8
Yes
180
AUTO47
AUTO47
AUTO47
Yes
133
(-)9
(-)9
(-)9
Yes
181
AUTO48
AUTO48
AUTO48
Yes
134
AUTO
AUTO
AUTO
Yes
182
AUTO49
AUTO49
AUTO49
Yes
135
AUTO2
AUTO2
AUTO2
Yes
183
AUTO50
AUTO50
AUTO50
Yes
136
AUTO3
CASH2
CASH2
Yes
184
AUTO51
AUTO51
AUTO51
Yes
137
AUTO4
CASH3
CASH3
Yes
185
AUTO52
AUTO52
AUTO52
Yes
138
AUTO5
CASH4
CASH4
Yes
186
AUTO53
AUTO53
AUTO53
Yes
139
AUTO6
CASH5
CASH5
Yes
187
AUTO54
AUTO54
AUTO54
Yes
140
AUTO7
AUTO7
AUTO7
Yes
188
AUTO55
AUTO55
AUTO55
Yes
141
AUTO8
AUTO8
AUTO8
Yes
189
AUTO56
AUTO56
AUTO56
Yes
142
AUTO9
AUTO9
AUTO9
Yes
190
AUTO57
AUTO57
AUTO57
Yes
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 18
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
191
AUTO58
AUTO58
AUTO58
Yes
239
CHECK3
CHECK3
CHECK3
Yes
192
AUTO59
AUTO59
AUTO59
Yes
240
CHECK4
CHECK4
CHECK4
Yes
193
AUTO60
AUTO60
AUTO60
Yes
241
CHECK5
CHECK5
CHECK5
Yes
194
AUTO61
AUTO61
AUTO61
Yes
242
CHECK6
CHECK6
CHECK6
Yes
195
AUTO62
AUTO62
AUTO62
Yes
243
CHECK7
CHECK7
CHECK7
Yes
196
AUTO63
AUTO63
AUTO63
Yes
244
CHECK8
CHECK8
CHECK8
Yes
197
AUTO64
AUTO64
AUTO64
Yes
245
CHECK9
CHECK9
CHECK9
Yes
198
AUTO65
AUTO65
AUTO65
Yes
246
CHARGE1
CHARGE1
CHG1
Yes
199
AUTO66
AUTO66
AUTO66
Yes
247
CHARGE2
CHARGE2
CHG2
Yes
200
AUTO67
AUTO67
AUTO67
Yes
248
CHARGE3
CHARGE3
CHG3
Yes
201
AUTO68
AUTO68
AUTO68
Yes
249
CHARGE4
CHARGE4
CHG4
Yes
202
AUTO69
AUTO69
AUTO69
Yes
250
CHARGE5
CHARGE5
CHG5
Yes
203
AUTO70
AUTO70
AUTO70
Yes
251
CHARGE6
CHARGE6
CHG6
Yes
204
AUTO71
AUTO71
AUTO71
Yes
252
CHARGE7
CHARGE7
CHG7
Yes
205
AUTO72
AUTO72
AUTO72
Yes
253
CHARGE8
CHARGE8
CHG8
Yes
206
AUTO73
AUTO73
AUTO73
Yes
254
CHARGE9
CHARGE9
CHG9
Yes
207
AUTO74
AUTO74
AUTO74
Yes
255
CONV1
Yes
AUTO75
AUTO75
AUTO75
Yes
CURRENCY
CONVERSION1
CONV1
208
209
AUTO76
AUTO76
AUTO76
Yes
256
CURRENCY
CONVERSION2
CONV2
CONV2
Yes
210
AUTO77
AUTO77
AUTO77
Yes
257
CONV3
Yes
AUTO78
AUTO78
AUTO78
Yes
CURRENCY
CONVERSION3
CONV3
211
212
AUTO79
AUTO79
AUTO79
Yes
258
CONV4
CONV4
Yes
213
AUTO80
AUTO80
AUTO80
Yes
CURRENCY
CONVERSION4
214
AUTO81
AUTO81
AUTO81
Yes
259
RECEIVED ON
ACCOUNT
RA
RA
Yes
215
AUTO82
AUTO82
AUTO82
Yes
260
RA2
Yes
AUTO83
AUTO83
AUTO83
Yes
RECEIVED ON
ACCOUNT2
RA2
216
217
AUTO84
AUTO84
AUTO84
Yes
261
PAID OUT
PO
PO
Yes
218
AUTO85
AUTO85
AUTO85
Yes
262
PAID OUT2
PO2
PO2
Yes
263
CHECK
CASHING1
CA/CHK1
CA/CHK_1
Yes
264
CHECK
CASHING2
CA/CHK2
CA/CHK_2
Yes
265
CHECK
CASHING3
CA/CHK3
CA/CHK_3
Yes
266
CHECK
CASHING4
CA/CHK4
CA/CHK_4
Yes
267
CHECK
CASHING5
CA/CHK5
CA/CHK_5
Yes
268
CHECK
CASHING6
CA/CHK6
CA/CHK_6
Yes
269
CHECK
CASHING7
CA/CHK7
CA/CHK_7
Yes
270
CHECK
CASHING8
CA/CHK8
CA/CHK_8
Yes
271
CHECK
CASHING9
CA/CHK9
CA/CHK_9
Yes
272
EAT IN1
EATIN1
EATIN1
Yes
273
EAT IN2
EATIN2
EATIN2
Yes
274
EAT IN3
EATIN3
EATIN3
Yes
275
Message1 (For KP)
MESSAGE1
MSG1
Yes
276
Message2 (For KP)
MESSAGE2
MSG2
Yes
219
AUTO86
AUTO86
AUTO86
Yes
220
AUTO87
AUTO87
AUTO87
Yes
221
AUTO88
AUTO88
AUTO88
Yes
222
AUTO89
AUTO89
AUTO89
Yes
223
AUTO90
AUTO90
AUTO90
Yes
224
AUTO91
AUTO91
AUTO91
Yes
225
AUTO92
AUTO92
AUTO92
Yes
226
AUTO93
AUTO93
AUTO93
Yes
227
AUTO94
AUTO94
AUTO94
Yes
228
AUTO95
AUTO95
AUTO95
Yes
229
AUTO96
AUTO96
AUTO96
Yes
230
AUTO97
AUTO97
AUTO97
Yes
231
AUTO98
AUTO98
AUTO98
Yes
232
AUTO99
AUTO99
AUTO99
Yes
233
CASH2
CASH2
CA2
Yes
234
CASH3
CASH3
CA3
Yes
235
CASH4
CASH4
CA4
Yes
236
CASH5
CASH5
CA5
Yes
237
CHECK
CHECK
CHECK
Yes
238
CHECK2
CHECK2
CHECK2
Yes
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 19
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
277
Message3 (For KP)
MESSAGE3
MSG3
Yes
324
PLU MENU44
PLU MENU 44
PLU_MENU44
No
278
Message4 (For KP)
MESSAGE4
MSG4
Yes
325
PLU MENU45
PLU MENU 45
PLU_MENU45
No
279
Message5 (For KP)
MESSAGE5
MSG5
Yes
326
PLU MENU46
PLU MENU 46
PLU_MENU46
No
280
MAIL MESSAGE
MAIL
MESSAGE
MAIL_MSG
Yes
327
PLU MENU47
PLU MENU 47
PLU_MENU47
No
328
PLU MENU48
PLU MENU 48
PLU_MENU48
No
281
PLU MENU1
PLU MENU 1
PLU_MENU01
No
329
PLU MENU49
PLU MENU 49
PLU_MENU49
No
282
PLU MENU2
PLU MENU 2
PLU_MENU02
No
330
PLU MENU50
PLU MENU 50
PLU_MENU50
No
283
PLU MENU3
PLU MENU 3
PLU_MENU03
No
331
MACRO1
MACRO1
MACRO1
Yes
284
PLU MENU4
PLU MENU 4
PLU_MENU04
No
332
MACRO2
MACRO2
MACRO2
Yes
285
PLU MENU5
PLU MENU 5
PLU_MENU05
No
333
MACRO3
MACRO3
MACRO3
Yes
286
PLU MENU6
PLU MENU 6
PLU_MENU06
No
334
MACRO4
MACRO4
MACRO4
Yes
287
PLU MENU7
PLU MENU 7
PLU_MENU07
No
335
CAPTURE1
CAP.1
CAP.1
Yes
288
PLU MENU8
PLU MENU 8
PLU_MENU08
No
336
CAPTURE2
CAP.2
CAP.2
Yes
289
PLU MENU9
PLU MENU 9
PLU_MENU09
No
337
CAPTURE3
CAP.3
CAP.3
Yes
290
PLU MENU10
PLU MENU 10
PLU_MENU10
No
338
CAPTURE4
CAP.4
CAP.4
Yes
291
PLU MENU11
PLU MENU 11
PLU_MENU11
No
339
CAPTURE5
CAP.5
CAP.5
Yes
292
PLU MENU12
PLU MENU 12
PLU_MENU12
No
340
CAPTURE6
CAP.6
CAP.6
Yes
293
PLU MENU13
PLU MENU 13
PLU_MENU13
No
341
CAPTURE7
CAP.7
CAP.7
Yes
294
PLU MENU14
PLU MENU 14
PLU_MENU14
No
342
CAPTURE8
CAP.8
CAP.8
Yes
295
PLU MENU15
PLU MENU 15
PLU_MENU15
No
343
CAPTURE9
CAP.9
CAP.9
Yes
296
PLU MENU16
PLU MENU 16
PLU_MENU16
No
344
CAPTURE10
CAP.10
CAP.10
Yes
297
PLU MENU17
PLU MENU 17
PLU_MENU17
No
345
PLU MENU18
PLU MENU 18
PLU_MENU18
No
FUNC
MENU 01
FUNC
_MENU01
No
298
FUNCTION
MENU 1
299
PLU MENU19
PLU MENU 19
PLU_MENU19
No
346
PLU MENU20
PLU MENU 20
PLU_MENU20
No
FUNC
MENU 02
FUNC
_MENU02
No
300
FUNCTION
MENU 2
301
PLU MENU21
PLU MENU 21
PLU_MENU21
No
347
FUNCTION
MENU 3
FUNC
MENU 03
FUNC
_MENU03
No
302
PLU MENU22
PLU MENU 22
PLU_MENU22
No
348
PLU MENU23
PLU MENU 23
PLU_MENU23
No
FUNCTION
MENU 4
FUNC
MENU 04
FUNC
_MENU04
No
303
304
PLU MENU24
PLU MENU 24
PLU_MENU24
No
349
PLU MENU25
PLU MENU 25
PLU_MENU25
No
FUNC
MENU 05
FUNC
_MENU05
No
305
FUNCTION
MENU 5
306
PLU MENU26
PLU MENU 26
PLU_MENU26
No
350
FUNCTION
MENU 6
FUNC
MENU 06
FUNC
_MENU06
No
307
PLU MENU27
PLU MENU 27
PLU_MENU27
No
351
PLU MENU28
PLU MENU 28
PLU_MENU28
No
FUNCTION
MENU 7
FUNC
MENU 07
FUNC
_MENU07
No
308
309
PLU MENU29
PLU MENU 29
PLU_MENU29
No
352
PLU MENU30
PLU MENU 30
PLU_MENU30
No
FUNC
MENU 08
FUNC
_MENU08
No
310
FUNCTION
MENU 8
311
PLU MENU31
PLU MENU 31
PLU_MENU31
No
353
FUNCTION
MENU 9
FUNC
MENU 09
FUNC
_MENU09
No
312
PLU MENU32
PLU MENU 32
PLU_MENU32
No
354
PLU MENU33
PLU MENU 33
PLU_MENU33
No
FUNCTION
MENU 10
FUNC
MENU 10
FUNC
_MENU10
No
313
314
PLU MENU34
PLU MENU 34
PLU_MENU34
No
355
FUNCTION
MENU 11
FUNC
MENU 11
FUNC
_MENU11
No
315
PLU MENU35
PLU MENU 35
PLU_MENU35
No
356
PLU MENU36
PLU MENU 36
PLU_MENU36
No
FUNCTION
MENU 12
FUNC
MENU 12
FUNC
_MENU12
No
316
317
PLU MENU37
PLU MENU 37
PLU_MENU37
No
357
PLU MENU38
PLU MENU 38
PLU_MENU38
No
FUNC
MENU 13
FUNC
_MENU13
No
318
FUNCTION
MENU 13
319
PLU MENU39
PLU MENU 39
PLU_MENU39
No
358
FUNCTION
MENU 14
FUNC
MENU 14
FUNC
_MENU14
No
320
PLU MENU40
PLU MENU 40
PLU_MENU40
No
359
PLU MENU41
PLU MENU 41
PLU_MENU41
No
FUNCTION
MENU 15
FUNC
MENU 15
FUNC
_MENU15
No
321
322
PLU MENU42
PLU MENU 42
PLU_MENU42
No
360
PLU MENU43
PLU MENU 43
PLU_MENU43
No
FUNCTION
MENU 16
FUNC
MENU 16
FUNC
_MENU16
No
323
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 20
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
Jump
to
key
No.
361
FUNCTION
MENU 17
FUNC
MENU 17
FUNC
_MENU17
No
362
FUNCTION
MENU 18
FUNC
MENU 18
FUNC
_MENU18
363
FUNCTION
MENU 19
FUNC
MENU 19
364
FUNCTION
MENU 20
365
Jump
to
key
No.
FUNCTION
DISPLAY KEY
TOUCH KEY
Text
Func.
Menu
390
GASOLINE SALES
SBTL 16
GAS16 ST
GAS16_ST
Yes
No
391
GASOLINE SALES
SBTL 17
GAS17 ST
GAS17_ST
Yes
FUNC
_MENU19
No
392
GASOLINE SALES
SBTL 18
GAS18 ST
GAS18_ST
Yes
FUNC
MENU 20
FUNC
_MENU20
No
393
GASOLINE SALES
SBTL 19
GAS19 ST
GAS19_ST
Yes
FUNCTION
MENU 21
FUNC
MENU 21
FUNC
_MENU21
No
394
GASOLINE SALES
SBTL 20
GAS20 ST
GAS20_ST
Yes
366
FUNCTION
MENU 22
FUNC
MENU 22
FUNC
_MENU22
No
395
GASOLINE SALES
SBTL 21
GAS21 ST
GAS21_ST
Yes
367
FUNCTION
MENU 23
FUNC
MENU 23
FUNC
_MENU23
No
396
GASOLINE SALES
SBTL 22
GAS22 ST
GAS22_ST
Yes
368
FUNCTION
MENU 24
FUNC
MENU 24
FUNC
_MENU24
No
397
GASOLINE SALES
SBTL 23
GAS23 ST
GAS23_ST
Yes
369
FUNCTION
MENU 25
FUNC
MENU 25
FUNC
_MENU25
No
398
GASOLINE SALES
SBTL 24
GAS24 ST
GAS24_ST
Yes
370
FUNCTION
MENU 26
FUNC
MENU 26
FUNC
_MENU26
No
399
GASOLINE SALES
SBTL 25
GAS25 ST
GAS25_ST
Yes
371
FUNCTION
MENU 27
FUNC
MENU 27
FUNC
_MENU27
No
400
GASOLINE SALES
SBTL 26
GAS26 ST
GAS26_ST
Yes
372
FUNCTION
MENU 28
FUNC
MENU 28
FUNC
_MENU28
No
401
GASOLINE SALES
SBTL 27
GAS27 ST
GAS27_ST
Yes
373
FUNCTION
MENU 29
FUNC
MENU 29
FUNC
_MENU29
No
402
GASOLINE SALES
SBTL 28
GAS28 ST
GAS28_ST
Yes
374
FUNCTION
MENU 30
FUNC
MENU 30
FUNC
_MENU30
No
375
GASOLINE SALES
SBTL 1
GAS1 ST
GAS1_ST
Yes
376
GASOLINE SALES
SBTL 2
GAS2 ST
GAS2_ST
Yes
377
GASOLINE SALES
SBTL 3
GAS3 ST
GAS3_ST
Yes
378
GASOLINE SALES
SBTL 4
GAS4 ST
GAS4_ST
Yes
379
GASOLINE SALES
SBTL 5
GAS5 ST
GAS5_ST
Yes
380
GASOLINE SALES
SBTL 6
GAS6 ST
GAS6_ST
Yes
381
GASOLINE SALES
SBTL 7
GAS7 ST
GAS7_ST
Yes
382
GASOLINE SALES
SBTL 8
GAS8 ST
GAS8_ST
Yes
383
GASOLINE SALES
SBTL 9
GAS9 ST
GAS9_ST
Yes
384
GASOLINE SALES
SBTL 10
GAS10 ST
GAS10_ST
Yes
385
GASOLINE SALES
SBTL 11
GAS11 ST
GAS11_ST
Yes
386
GASOLINE SALES
SBTL 12
GAS12 ST
GAS12_ST
Yes
387
GASOLINE SALES
SBTL 13
GAS13 ST
GAS13_ST
Yes
388
GASOLINE SALES
SBTL 14
GAS14 ST
GAS14_ST
Yes
389
GASOLINE SALES
SBTL 15
GAS15 ST
GAS15_ST
Yes
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 21
4. KEY INITIAL [#951]
[TOUCH KEY DISPLAY]
Touch key (2 x 6 character) is displayed by centering as follows.
Text sample
1
2
3
4
a
5
Key text, key color, and menu title of HOME MENU DISPLAY and
FUNCTION MENU are initialized.
6
a
ab
a
KEY POSITION CODE
Normal key version
b
R
abc
a
abcd
a
abcde
a
b
b
b
c
c
c
abcdef
a
b
c
abcdefg
a
b
c
d
d e
d
e
f
d
e
f
J
16
22
28
34
40
46
52
58
64
70
76
82
5
10
15
21
27
33
39
45
51
57
63
69
75
81
4
9
14
20
26
32
38
44
50
56
62
68
74
80
3
8
13
19
25
31
37
43
49
55
61
67
73
79
2
7
12
18
24
30
36
42
48
54
60
66
72
78
1
6
11
17
23
29
35
41
47
53
59
65
71
77
Flat key version
g
R
abcde_fg
abcdef_g
a b c d e
f g
a
b
c
d
e
f
g
abcdef_gh
abcdef_ghi
a
b
a
b
c
g
d
h
e
c
d
e
f
f
g h i
abcdef_ghij
a
abcdef_ghijk
a
abcdefghijkl
a
g
abcdefgh
b
g
d
i
e
j
f
25
34
43
52
61
70
79
88
97
106
115
124
133
142
16
24
33
42
51
60
69
78
87
96
105
114
123
132
141
7
15
23
32
41
50
59
68
77
86
95
104
113
122
131
140
6
14
22
31
40
49
58
67
76
85
94
103
112
121
130
139
5
13
21
30
39
48
57
66
75
84
93
102
111
120
129
138
4
12
20
29
38
47
56
65
74
83
92
101
110
119
128
137
3
11
19
28
37
46
55
64
73
82
91
100
109
118
127
136
2
10
18
27
36
45
54
63
72
81
90
99
108
117
126
135
1
9
17
26
35
44
53
62
71
80
89
98
107
116
125
134
b c d e f
g h i j k
b
h
a
c
i
b
f
a_bcdef g
c
h
J
8
d
j
c
g
e
k
f
l
“f” is began on a new line.
5. HOME MENU DISPLAY [#952]
d e
h
a
b c d e f
HOME MENU DISPLAY
Item
“g” is not displayed.
MENU title
Symbol’s “_” is began on a new line. A second “_” symbol will be
ignored by the system. Maximum of 2 lines for description.
HOME key#1
More than 7 characters after “_” cannot be set.
HOME key#2
(text)
MENU TITLE
MRS
HOME MENU
(nothing)
Function key list
(All key)
INHIBIT
(nothing)
Function key list
(All key)
INHIBIT
:
:
HOME key#15
Range/Detail
16 digits text
:
:
(nothing)
:
:
Function key list
(All key)
It can be programmed any function keys except B.S. keys.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 22
INHIBIT
6. PROGRAMMING OF THE Z CONTER
8. SRV FILE PROGRAMMING [JOB#971]
[JOB#930]
File creation, file deletion, and change of record count or block count.
Z REPORT COUNTER : Z COUNTER
[FILE TABLE GROUP LIST]
MRS
No.
0000
1
Dept
DEPARTMENT
CONSOLI.TRAN.Z1 Consolidation transaction Z1 report
counter
0000
2
PLU
ITEMS
3
LINK PLU
TABLES
SERVER Z1/Z2
Server Z1/Z2 report counter
0000
4
SERVER
PERSONNEL
HOURLY Z1
Hourly Z1 report counter
0000
5
GLU/PBLU (ALL)
GLU
PLU/UPC Z1/Z2
PLU/UPC Z1/Z2 report counter
0000
6
KP BUFFER
OTHERS
GLU Z1
GLU/PBLU Z1 report counter
0000
TRANS. Z2
Transaction Z2 report counter
0000
DISPLAY TEXT
TRANS. Z1
CONTENTS
Transaction Z1 report counter
Jump File group Name
NAME
If “06 ITEMS” is selected, cursor jumps to file No.6 “PLU/UPC”.
[FILE TABLE]
CONSOLI.TRAN.Z2 Consolidation Z2 report counter
0000
DAILY NET Z2
Daily net Z2 report counter
0000
DEPARTMENT Z1
Department Z1 report counter
0000
Group
NO.
DEPARTMENT Z2
Department Z2 report counter
0000
1
DEPT
1
1,2,3,5,6 / 10
EJ Z1
EJ Z1 REPORT COUNTER
0000
2
DEPT TEXT (8)
0
3
3
DEPT TEXT (16)
0
4
[JOB#942]
4
DEPT Mark Down
0
10 / 11,12,13,14
GRAND TOTAL : GT
5
Dept Term
0
6,11
6
PLU/UPC
1
15,16,17,19,21,27,29,
31,33,35
7
PLU/UPC PRICE 1
0
17,27,29,31,33,35
/ 28,30,32,34,36
8
PLU/UPC PRICE 1-6
0
18,37,39,41,43,45
/ 38,40,42,44,46
0
19
DISPLAY TEXT
CONTENTS
MRS
POSITIVE GT
GT2 (Positive GT): 13 digits
0000000000000
NEGATIVE GT
GT3 (Negative GT): 13 digits
0000000000000
TRAINING GT
Training GT : 13 digits
0000000000000
GT1 is obtained by the following equation.
FILE NAME
File table No.
(Create / Erase)
TYPE
9
PLU/UPC TEXT1 (8)
EQUATION: GT1 = GT2 - GT3
10
PLU/UPC TEXT1 (16)
0
20
GT programming will be inhibited after MRS3 operation.
11
PLU/UPC KP TEXT1 (12)
0
22
JOB#989 memory initial can be executed after MRS3 operation.
12
PLU/UPC TEXT 1-6 (8)
0
23
13
PLU/UPC TEXT 1-6 (16)
0
24
14
PLU/UPC KP TEXT 1-6 (12)
0
25
15
PLU stock
0
26
16
PLU ENH.SALES
0
29,30,31,32,33,34,35,
36,60, 61,62,63,195
/ 196
17
PLU Term
0
28,30,32,34,36
18
DYNAMIC UPC
1
47,48,49,52,53,54,58,
60,62,195
19
DYNAMIC UPC PRICE 1
0
49,58,60,62,195
/59,61,63,196
20
DYNAMIC UPC PRICE 1-6
0
50,64,66,68,197
/ 65,67,69,198
0
51
7. PROGRAMMING OF PGM2-MODE SECRET
CODES
[JOB#944]
MODE SECRET# : MODE SECRET#
DISPLAY TEXT
CONTENTS
MRS
OP XZ MODE
OP X/Z mode secret code (4 digits)
0000
X1 OPERATE
X1 operation secret code (4 digits)*1
0000
Z1 OPERATE
Z1 operation secret code (4 digits)*2
0000
X2 OPERATE
X2 operation secret code (4 digits)*1
0000
21
DYNAMIC UPC TEXT1 (8)
Z2 OPERATE
*2
Z2 operation secret code (4 digits)
0000
22
DYNAMIC UPC TEXT1 (16)
0
52
PGM1 MODE
PGM1 mode secret code (4 digits)
0000
23
DYNAMIC UPC KP TEXT1
(12)
0
54
24
DYNAMIC UPC TEXT1-6
(8)
0
55
25
DYNAMIC UPC TEXT1-6
(16)
0
56
26
DYNAMIC UPC KP TEXT
1-6 (12)
0
57
27
Term DYNAMIC UPC
0
59, 61, 63, 196
28
UPC PGM PICK UP
1
70
PGM2 MODE
PGM2 mode secret code (4 digits)
0000
SD CARD MODE
SD card mode secret code
(4 digits)
0000
* If “0” is entered “compulsory secret code entry” is canceled.
* 1: “X OPERATION SECRET CODE” is used when an operator selects
“READING” menu in X/Z mode.
* 2: “Z OPERATION SECRET CODE” is used when an operator selects
the menu except “READING” (“RESETTING” etc.) in X/Z mode.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 23
Group
NO.
Group
NO.
File table No.
(Create / Erase)
FILE NAME
File table No.
(Create / Erase)
TYPE
FILE NAME
TYPE
29
DYNAMIC UPC PGM PICK
UP
1
71
69
RJE Scheduler buffer
0
184,185,186,187,188,
189,190
30
EAN X/Z PICK UP
1
72
70
ONLINE PRINT buffer
1
191
31
DYNAMIC UPC X/Z PICK
UP
1
194
71
Mail Spool file (Machine)
1
192
72
Mail Spool file (Server)
4
193
32
Link PLU
1
73
73
168
Combo Meal
1
74,75,272
RECEIVE CHARGE
POSTING
1
33
34
Combo Meal KP TEXT
0
76
74
ACCT BAL offline file
1
200
35
Condiment table
1
80,81,154
75
ELECTRONIC JOURNAL
1
212 / 213
36
Mix&Match Table
1
82,83,214
37
Mix&Match Sold Buffer
1
84,207
38
Server
1
91,92,93,94,95
/ 96, 97,98,99,102
39
Server Term
0
96
Type 2 Create/Erase and Increase/Decrease the number of blocks.
40
Sign off Server (IRC)
2
105,106
41
Manager
1
107
Type 3 Create/Erase and Increase/Decrease the number of records
for label and data individually.
42
GLU/PBLU (Preset + buffer)
3
132,157,158
43
Closed GLU
1
133,199
44
AUTO GLU Generate code
1
134
* :The files which are created or erased by the entry of the group No.
45
GLU/PBLU Rcv buffer (IRC)
2
124
**: For individual erase
46
GLU/PBLU file
(Preset Only)
3
132,157,158
47
B.S./B.T. buffer (buffer Only)
0
122
48
Repeat round buffer
0
160,206
49
KP buffer
0
123,161
50
KP (IRC)
1
142,143
51
Message text (KP)
0
155,156
52
Term Transaction
0
87
53
All of term file
0
6,11,28,30,32,34,36,59,
61,63,87,96,196
54
Hourly
1
108,109
55
Daily net
1
113,114
56
Reg buffer
1
119,120,121,122,149,
151,159,160,202,203,
204,205
/ 124,125,127,130,131,
148,154,123,161,206,
214
57
CUSTOMER
1
162,163
58
CUSTOMER (SALES)
1
164,208,209
59
T-LOG buffer
1
126
60
Journal Log buffer
1
128
61
Receipt Window buffer
1
129
62
Ind. Pay buffer
0
130,131,148,150
Type 0 Create/Erase only
Type 1 Create/Erase and Increase/Decrease the number of records.
Type 4 Create/Erase and Increase/Decrease the number of records.
(corresponding with the number of blocks)
63
Positive No
1
166
64
Charge Positing
1
167
65
Negative No
1
169
66
Capture job
1
172,173
67
Capture job (sales)
3
174
68
RJE Command buffer
1
175,176,177,178,179,
180,181,182,183
/ 184,185,186,187,188,
189,190
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 24
FILE CONTENTS
Record
Table
No.
1
2
File Name
Normal
Flat
keyboard keyboard
DEPT PRESET
PRICE
BLOCK
MRS
MAX
20
10
99
20
10
99
0
#1
MRS
1
1
1
Label
Size
Data
Size
1
1
15
1
0
3
MAX
#2
3
TEXT (8 chara.)
99
1
0
1
0
8
4
TEXT (16 chara.)
20
10
99
1
1
1
0
16
5
DAILY
20
10
99
1
1
1
0
13
6
TERM
20
10
99
1
1
1
0
13
7
SAVE DAILY
0
99
1
0
1
0
13
8
CONSOLI.
0
99
1
0
1
0
13
9
RECEIVE
0
99
1
0
1
0
13
10
DAILY (Markdown)
0
99
1
0
18
0
8
11
TERM (Markdown)
0
99
1
0
18
0
8
12
SAVE DAILY ( Markdown)
0
99
1
0
18
0
8
13
CONSOL. (Markdown)
0
99
1
0
18
0
8
14
RECEIVE ( Markdown)
0
99
1
0
18
0
8
1000
500
****
1
1
7+2
48
16
FLAG
1000
500
****
15
1
1
0
2
17
PRICE1
1000
500
****
15
1
1
0
3
18
PRICE1-6
****
15
0
1
0
18
15
PLU PRESET
0
****
15
0
1
0
8
500
****
15
1
1
0
16
1000
500
****
15
0
1
0
12
1000
500
****
15
1
1
0
12
0
****
15
0
1
0
48
0
****
15
0
1
0
96
1
0
72
1
0
8
19
TEXT1 (8 chara.)
20
TEXT1 (16 chara.)
0
21
DISPLAY TEXT
22
KP TEXT1
23
TEXT1-6 (8 chara.)
24
TEXT1-6 (16 chara.)
25
KP TEXT1-6
0
****
15
0
26
STOCK
0
****
15
0
27
DAILY(Price1)
28
TERM(Price1)
29
COMBO DAILY(Price1)
30
COMBO TERM(Price1)
31
WASTE DAILY(Price1)
32
WASTE TERM(Price1)
33
REFUND DAILY(Price1)
34
REFUND TERM(Price1)
1000
1000
500
0
0
500
0
0
500
0
0
500
0
****
15
1
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
****
15
0
1
0
9
35
COUPON DAILY(Price1)
****
15
0
1
0
9
36
COUPON TERM(Price1)
0
****
15
0
1
0
9
37
DAILY(Price1-6)
0
****
15
0
6
0
9
38
TERM(Price1-6)
0
****
15
0
6
0
9
39
COMBO DAILY(Price1-6)
0
****
15
0
6
0
9
40
COMBO TERM(Price1-6)
0
****
15
0
6
0
9
41
WASTE DAILY(Price1-6)
0
****
15
0
6
0
9
42
WASTE TERM(Price1-6)
0
****
15
0
6
0
9
43
REFUND DAILY(Price1-6)
0
****
15
0
6
0
9
44
REFUND TERM(Price1-6)
0
****
15
0
6
0
9
45
COUPON DAILY(Price1)
0
****
15
0
6
0
9
46
COUPON TERM(Price1)
0
****
15
0
6
0
9
0
UP-810F/820N/820F (U)
500
SRV MODE PROGRAMMING (“SETTING”)
3 – 25
Record
Table
No.
47
BLOCK
MRS
File Name
Normal
Flat
keyboard keyboard
MAX
0
****
DYNAMIC UPC PRESET
#1
Label
Size
Data
Size
1
7+2
48
MRS
MAX
0
#2
48
FLAG
0
****
47
0
1
0
2
49
PRICE1
0
****
47
0
1
0
3
50
PRICE1-6
0
****
47
0
1
0
18
51
TEXT1 (8 chara.)
0
****
47
0
1
0
8
52
TEXT1 (16 chara.)
0
****
47
0
1
0
16
53
DISPLAY TEXT
0
****
47
0
1
0
12
54
KP TEXT1
0
****
47
0
1
0
12
55
TEXT1-6 (8 chara.)
0
****
47
0
1
0
48
56
TEXT1-6 (16 chara.)
0
****
47
0
1
0
96
57
KP TEXT1-6
0
****
47
0
1
0
72
58
DAILY(Price1)
0
****
47
0
1
0
9
59
TERM(Price1)
0
****
47
0
1
0
9
60
WASTE DAILY(Price1)
0
****
47
0
1
0
9
61
WASTE TERM(Price1)
0
****
47
0
1
0
9
62
REFUND DAILY(Price1)
0
****
47
0
1
0
9
63
REFUND TERM(Price1)
0
****
47
0
1
0
9
64
DAILY(Price1-6)
0
****
47
0
6
0
9
65
TERM(Price1-6)
0
****
47
0
6
0
9
66
WASTE DAILY(Price1-6)
0
****
47
0
6
0
9
67
WASTE TERM(Price1-6)
0
****
47
0
6
0
9
68
REFUND DAILY(Price1-6)
0
****
47
0
6
0
9
69
REFUND TERM(Price1-6)
0
****
47
0
6
0
9
100
****
1
1
7+2
0
0
****
0
1
7+2
0
70
EAN PGM PICK UP
71
DYNAMIC EAN PGM PICK UP
72
EAN X/Z PICK UP
100
****
1
1
7+2
0
73
LINK PLU
10
99
1
1
1
35
74
COMBO MEAL
0
10
20
0
1
1
124
TEXT
0
10
20
74
0
1
0
16
76
KP TEXT
0
10
20
74
0
1
0
12
77
PLU MENU KEY
1
1
1
211
78
PLU MENU KEY2
75
79
80
81
50
PLU MENU KEY TEXT
Condiment Table
50
50
77
1
1
1
84
50
50
77
1
1
1
16
0
1
1
198
80
0
1
1
16
1
1
1
5
1
1
1
12
0
Condiment TEXT
50
10
99
0
****
82
MIX & MATCH TABLE
10
99
83
MIX & MATCH TEXT
10
99
82
84
MIX & MATCH SOLD
100
100
82
85
TRANSACTION LABEL
317
317
1
1
1
6
1
1
2
0
86
DAILY
317
317
85
1
1
0
9
87
TERM
317
317
85
1
1
0
9
88
SAVE DAILY
0
168
85
0
1
0
9
89
CONSOL.
0
168
85
0
1
0
9
0
168
85
0
1
0
9
15
255
1
1
2
115
90
91
RECEIVE
SERVER PRESET
92
FLAG
15
255
91
1
1
0
3
93
TEXT
15
255
91
1
1
0
8
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 26
Record
Table
No.
94
BLOCK
MRS
File Name
Normal
Flat
keyboard keyboard
MAX
160
160
SERVER TRNSACTION LABEL
#1
MRS
MAX
#2
Label
Size
Data
Size
15
15
91
2
0
95
DAILY
160
160
92
15
15
91
0
9
96
TERM
160
160
92
15
15
91
0
9
97
(Reserved)
98
(Reserved)
96
96
92
1
1
2
0
96
96
92
1
1
0
9
0
96
92
0
1
2
0
0
96
105
0
1
0
9
99
100
(Reserved)
TOTAL SERVER (BUFFER) LABEL
101
TOTAL
102
(Reserved)
103
(Reserved)
104
(Reserved)
105
106
SIGN OFF SERVER TRANS. LABEL
RECEIVE
107
MANAGER PRESET
0
99
0
1
0
2
108
HOURLY LABEL
96
96
1
1
1
0
109
DAILY
96
96
108
1
1
0
11
110
SAVE DAILY
0
96
108
0
1
0
11
111
CONSOL.
0
96
108
0
1
0
11
112
RECEIVE
0
96
108
0
1
0
11
32
32
1
1
3
0
32
32
113
1
1
0
8
0
32
113
0
1
3
0
0
32
113
0
1
0
8
113
114
115
116
117
118
DAILY NET LABEL
TOTAL
DAILY NET CONSOL. LABEL
CONSOL.
DAILY NET RCV LABEL
RECEIVE
0
32
113
0
1
3
0
0
32
113
0
1
0
8
119
Reg buffer
150
****
1
1
0
62
120
Reg Edit buffer
150
****
119
1
1
0
62
121
GLU/PBLU buffer
122
B.S./B.T. buffer
123
KP buffer
124
GLU/PBLU Rcv buffer
125
GLU/PBLU Save buffer
126
T-LOG buffer
****
119
1
1
0
62
****
119
0
1
0
62
150
****
119
2
2
0
52
0
****
119
0
1
0
62
0
****
119
1200
****
150
0
150
127
T-LOG RECEIVE buffer
0
****
128
Journal Log buffer
100
****
129
Receipt Window buffer
30
****
130
Ind. PAY Reg Edit buffer
0
****
119
****
119
131
Ind. PAY GLU/PBLU buffer
132
GLU/PBLU
133
Closed GLU
0
119
0
1
0
62
1
1
0
33
0
1
0
33
1
1
0
50
1
1
3+2
20
0
1
0
62
0
1
0
62
********
0
1
2+5
57
0
****
0
1
2+2
144
0-0
2-200
134
AUTO GLU Generate Code
0
****
0
1
0
11
135
Logo Text
15
15
1
1
1
48
136
Function TEXT
457
457
1
1
2
12
137
Dept Group Text
9
9
1
1
1
12
138
PLU Group Text
99
99
1
1
1
12
139
Currency descriptor text
4
4
1
1
1
4
140
VP TEXT
3
3
1
1
1
48
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 27
Record
Table
No.
BLOCK
MRS
File Name
Normal
Flat
keyboard keyboard
MAX
1
1
#1
Label
Size
Data
Size
1
1
64
1
1
1
4
1
1
0
12
MRS
MAX
1
#2
141
SCROLL MESSAGE TEXT
142
KP PRESET
9
9
143
KP TEXT
9
9
144
Direct Key Table
142
142
1
1
1
35
145
Scale Table
9
9
1
1
1
2
146
Auto Key Table
99
99
1
1
2
100
147
Stacked Report Table
20
20
2
2
1
16
148
Ind. Pay Reg buffer
149
Bill buffer
150
Ind. Pay Itemizer buffer
151
Copy Buffer
142
0
****
119
0
1
0
470
150
****
119
1
1
0
62
0
1
1
650
1
1
0
62
0
****
150
****
119
152
BS DESTINATION BUFFER
30
****
1
1
3+2
20
153
BS SOURCE BUFFER
30
****
1
1
3+2
20
0
1
0
62
1
1
1
2
1
1
0
16
0
1
4
16
154
CONDIMENT EDIT buffer
155
Message Preset
0
150
5
156
Message Text
157
OPEN GLU BUFFER
0
158
DISP OPEN GLU BUFFER
0
159
Receipt Window Display BUFFER
****
119
5
5
5
150
150
150
****
130
****
132
0
1
2
18
****
119
1
1
0
62
160
REPEAT ROUND BUFFER
150
****
119
1
1
0
32
161
Reg buffer FOR KP
150
****
119
1
1
0
62
162
CUSTOMER PRESET
163
TEXT
164
CUSTOMER SALES
165
MACRO TABLE
166
POSITIVE#
100
167
CHARGE POSTING (POSITIVE#SALES)
100
168
CHARGE POSTING FOR IRC RCV
0
****
0
1
7
8
0
****
162
0
1
0
80
0-0
********
162
0
1
7+5
20
4
4
1
1
1
30
50
****
1
1
8
0
50
****
1
1
2
14
0
1
2
14
****
0
167
169
NEGATIVE#
****
1
1
8
1
170
CAPTURE KEY PRESET
10
10
1
1
1
2
171
CAPTURE KEY TEXT
10
10
1
1
0
12
172
CAPTURE JOB PRESET
10
99
1
1
1
12
173
100
CAPTURE JOB TEXT
174
CAPTURE SALES
175
RJE BUFFER
176
50
10
10-200
COMMNAD BUFFER
10-100
170
99
172
1
1
0
52
99****
172
1
1
1
29
3
****
1
1
0
6
3
****
1
1
0
7
177
PFLD1 BUFFER
3
****
1
1
0
5
178
PFLD2 BUFFER
3
****
1
1
0
255
179
PFLD3 BUFFER
3
****
1
1
0
255
180
PFLD4 BUFFER
3
****
1
1
0
255
181
PFLD5 BUFFER
3
****
1
1
0
3
182
STATUS ONLINE BUFF
3
****
1
1
0
4
STATUS INLINE BUFFER
3
****
1
1
0
254
0
****
0
1
1
6
183
184
RJE SCHEDULE BUFFER
175
185
SCHEDULE COMMNAD BUFFER
0
****
175
0
1
0
7
186
SCHEDULE PFLD1 BUFFER
0
****
175
0
1
0
5
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 28
Record
Table
No.
187
BLOCK
MRS
File Name
Label
Size
Data
Size
1
0
150
Normal
Flat
keyboard keyboard
MAX
#1
MRS
MAX
0
****
175
0
SCHEDULE PFLD2 BUFFER
#2
188
SCHEDULE PFLD3 BUFFER
0
****
175
0
1
0
150
189
SCHEDULE PFLD4 BUFFER
0
****
175
0
1
0
150
0
****
175
150
****
190
191
SCHEDULE PFLD5 BUFFER
ONLINE PRINT SPOOL
0
1
0
3
1
1
0
20
0
20
0
20
192
MACHINE MESSAGE SPOOL FILE
0
****
0
1
193
SERVER MESSAGE SPOOL FILE
0
****
0
15
91
194
DYNAMIC EAN X/Z PICK UP
0
****
0
1
7+2
0
195
D-EAN COUPON DAILY (Price1)
0
****
48
0
1
0
9
196
D-EAN COUPON TERM (Price1)
0
****
48
0
1
0
9
197
D-EAN COUPON DAILY (Price1-6)
0
****
48
0
6
0
9
198
D-EAN COUPON TERM (Price1-6)
0
****
48
0
6
0
9
199
CLOSED GLU AMOUNT
0
****
131
0
1
2+2
145
200
ACCOUNT BALANCE OFFLINE
0
****
0
1
0
108
201
Cat Print Image Buffer
100
****
5
5
0
48
202
HOLD REG BUFFER
0
32
119
0
1
0
62
203
HOLD Receipt Window Display BUFFER
0
32
119
0
1
0
62
204
HOLD REG EDIT BUFFER
0
32
119
0
1
0
62
205
HOLD GLU/PBLU BUFFER
0
32
119
0
1
0
62
206
HOLD REPEAT ROUND BUFFER
0
32
119
0
1
0
32
207
HOLD MIX&MATCH SOLD BUFFER
100
100
84
2
1
0
24
208
Customer WORK Label
0
160
85
0
1
2
0
209
Customer WORK Daily
0
****
208
0
1
0
9
210
Customer receive WORK Label
0
****
85
0
1
2
0
211
Customer receive WORK Daily
0
****
210
0
1
0
9
1
1
0
30
0
1
0
30
212
Electronic Journal buffer1
213
Electronic Journal consol Buffer
1500
****
0
****
212
214
MIX&MATCH DISC. BUFFER
0
32
119
0
1
0
62
215
PLU save Daily (Price1)
0
****
15
0
1
0
9
216
PLU consol (Price1)
0
****
15
0
1
0
9
217
PLU receive (Price1)
0
****
15
0
1
0
9
218
PLU (Combo) save Daily (Price1)
0
****
15
0
1
0
9
219
PLU (Combo) consol (Price1)
0
****
15
0
1
0
9
220
PLU (Combo) receive (Price1)
0
****
15
0
1
0
9
221
PLU (Waste) save Daily (Price1)
0
****
15
0
1
0
9
222
PLU (Waste) consol (Price1)
0
****
15
0
1
0
9
223
PLU (Waste) receive (Price1)
0
****
15
0
1
0
9
224
PLU (Refund) save Daily (Price1)
0
****
15
0
1
0
9
225
PLU (Refund) consol (Price1)
0
****
15
0
1
0
9
226
PLU (Refund) receive (Price1)
0
****
15
0
1
0
9
227
PLU (Coupon) save Daily (Price1)
0
****
15
0
1
0
9
228
PLU (Coupon) consol (Price1)
0
****
15
0
1
0
9
229
PLU (Coupon) receive (Price1)
0
****
15
0
1
0
9
230
PLU save Daily (Price1-6)
0
****
15
0
6
0
9
231
PLU consol (Price1-6)
0
****
15
0
6
0
9
232
PLU receive (Price1-6)
0
****
15
0
6
0
9
233
PLU (Combo) save Daily(Price1-6)
0
****
15
0
6
0
9
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 29
Record
Table
No.
BLOCK
MRS
File Name
Normal
Flat
keyboard keyboard
MAX
#1
MRS
MAX
#2
Label
Size
Data
Size
234
PLU (Combo) consol (Price1-6)
0
****
15
0
6
0
9
235
PLU (Combo) receive (Price1-6)
0
****
15
0
6
0
9
236
PLU (Waste) save Daily (Price1-6)
0
****
15
0
6
0
9
237
PLU (Waste) consol (Price1-6)
0
****
15
0
6
0
9
238
PLU (Waste) receive (Price1-6)
0
****
15
0
6
0
9
239
PLU (Refund) save Daily (Price1-6)
0
****
15
0
6
0
9
240
PLU (Refund) consol (Price1-6)
0
****
15
0
6
0
9
241
PLU (Refund) receive (Price1-6)
0
****
15
0
6
0
9
242
PLU (Coupon) save Daily (Price1-6)
0
****
15
0
6
0
9
243
PLU (Coupon) consol (Price1-6)
0
****
15
0
6
0
9
244
PLU (Coupon) receive (Price1-6)
0
****
15
0
6
0
9
245
Daily Deposit LABEL
70
****
1
1
2
0
246
Daily Deposit Daily
70
****
1
1
0
9
245
247
Win Select Buffer
300
****
1
1
2
0
248
Dynamic UPC save Daily (Price1)
0
****
47
0
1
0
9
249
Dynamic UPC consol (Price1)
0
****
47
0
1
0
9
250
Dynamic UPC receive (Price1)
0
****
47
0
1
0
9
251
D-UPC (Waste) save Daily (Price1)
0
****
47
0
1
0
9
252
D-UPC (Waste) consol (Price1)
0
****
47
0
1
0
9
253
D-UPC (Waste) receive (Price1)
0
****
47
0
1
0
9
254
D-UPC (Refund) save0 Daily (Price1)
0
****
47
0
1
0
9
255
D-UPC (Refund) consol (Price1)
0
****
47
0
1
0
9
256
D-UPC (Refund) receive (Price1)
0
****
47
0
1
0
9
257
D-UPC (Coupon) save0 Daily (Price1)
0
****
47
0
1
0
9
258
D-UPC (Coupon) consol (Price1)
0
****
47
0
1
0
9
259
-UPC (Coupon) receive (Price1)
0
****
47
0
1
0
9
260
D-UPC save Daily (Price1-6)
0
****
47
0
6
0
9
261
D-UPC consol (Price1-6)
0
****
47
0
6
0
9
262
D-UPC receive (Price1-6)
0
****
47
0
6
0
9
263
D-UPC (Waste) save Daily (Price1-6)
0
****
47
0
6
0
9
264
D-UPC (Waste) consol (Price1-6)
0
****
47
0
6
0
9
265
D-UPC (Waste) receive (Price1-6)
0
****
47
0
6
0
9
266
D-UPC (Refund) save0 Daily (Price1-6)
0
****
47
0
6
0
9
267
D-UPC (Refund) consol (Price1-6)
0
****
47
0
6
0
9
268
D-UPC (Refund) receive (Price1-6)
0
****
47
0
6
0
9
269
D-UPC (Coupon) save0 Daily (Price1-6)
0
****
47
0
6
0
9
270
D-UPC (Coupon) consol (Price1-6)
0
****
47
0
6
0
9
271
D-UPC (Coupon) receive (Price1-6)
0
****
47
0
6
0
9
272
D-UPC (Coupon) consol (Price1)
0
****
47
0
1
0
9
273
D-UPC (Coupon) receive (Price1)
0
****
47
0
1
0
9
274
D-UPC save Daily (Price1-6)
0
****
47
0
6
0
9
275
D-UPC consol (Price1-6)
0
****
47
0
6
0
9
276
D-UPC receive (Price1-6)
0
****
47
0
6
0
9
277
D-UPC (Waste) save Daily (Price1-6)
0
****
47
0
6
0
9
278
D-UPC (Waste) consol (Price1-6)
0
****
47
0
6
0
9
279
D-UPC (Waste) receive (Price1-6)
0
****
47
0
6
0
9
280
D-UPC (Refund) save0 Daily (Price1-6)
0
****
47
0
6
0
9
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 30
Record
Table
No.
File Name
281
BLOCK
MRS
Normal
Flat
keyboard keyboard
MAX
#1
MRS
MAX
D-UPC (Refund) consol (Price1-6)
0
****
47
0
6
#2
Label
Size
Data
Size
0
9
282
D-UPC (Refund) receive (Price1-6)
0
****
47
0
6
0
9
283
D-UPC (Coupon) save0 Daily (Price1-6)
0
****
47
0
6
0
9
284
D-UPC (Coupon) consol (Price1-6)
0
****
47
0
6
0
9
285
D-UPC (Coupon) receive (Price1-6)
0
****
47
0
6
0
9
286
AUTO COMBO BUFFER
0
99
74
1
1
1
102
#1 : Same as the number of record of table no. N
#2 : The number of table is same as the number of record of table no. N
- : (Number of index record) - (Number of data record)
9. SUPERVISOR MODE ON/OFF
DISPLAY during transmission
BACKUP SEND
[JOB#985]
SUPERVISOR MODE : SUPERVISOR
TEXT
S U P E RV I S O R
MODE
CONTENTS
MRS
ON/OFF
P UP
SEND DATA
ALL RAM
SPEED
PROGRAMMED
+-----------------------------------------------+
| SENDING
00511 |
|
|
+-----------------------------------------------+
OFF
Note: Secret code for all modes are ignored when supervisor mode is
“ON”.
PREV.
SRV
NEXT
LIST
JOB title "BACKUP
SEND" or "BACKUP
RECEIVE"
<<Key Area>>
"SENDING" or
"RECEIVING",
Counter Progress bar
P DOWN
SERV.0001
0001
12:34
10.MEMORY INITIALIZE (EXCEPT GT MEMORY)
TIME DISPLAY is
freezed.
* Customer Display is not changed.
[JOB#989]
PRINT at the end of the job
MEMORY INITIAL : MEMORY INITIAL
TEXT
MEMORY INITIAL
CONTENTS
The message is printed on JOURNAL only.
MRS
YES/NO
NO
Print
(30 digits)
Totalizer memory initialize (except GT memory and EJ)
CONTENTS
All of counter, totalizer are initialized. But, GT1-GT3, EJ memory is
remained.
(HEADER)
BACKUP SEND
SEND OK
11.BACKUP DATA SEND/RECEIVE
(HEADER)
BACKUP RECEIVE
RECEIVE OK
JOB TITLE is printed.
MESSAGE is printed.
(This is Normal End Message)
[JOB#996]
DATA SEND : DATA SEND
SEND DATA
ALL
SSP
SPEED
PROGRAMMED SPEED
38400 bps
19200 bps
9600 bps
4800 bps
2400 bps
COM. ERROR
XX
ERROR MESSAGE, ERROR CODE
DATA ERROR
XX
ERROR MESSAGE, ERROR CODE
COM. TIME-OUT
ERROR MESSAGE
* All ERROR MESSAGE are fixed.
* ERROR CODE : 01 = ID No. error (ID No. in IDENQ is not correct.)
02 = Parity error
03 = Check sum error
04 = Data size error
05 = Hardware error
06 = Power off error
07 = Time out error
11 = Transmit data size error
12 = Block sequence error
(Irregular sequence No. has been received)
13 = NAK code error
(NAK code has been received.)
15 = ECR TYPE error
(Models of two ECR is different.)
[JOB#998]
DATA RECEIVE : DATA RECEIVE
SPEED
JOB TITLE is printed.
MESSAGE is printed.
(This is Normal End Message)
PROGRAMMED SPEED
38400 bps
19200 bps
9600 bps
4800 bps
2400 bps
* “PROGRAMMED” means “SPEED is specified by SRV#903-A”.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 31
[JOB#990]
Item
(text)
SSP INPUT
TEXT
CONTENTS
SSP#
SSP No. Entry
(STEP#)
SSP DATA
DEPT.CODE
Sign
SIGN
Amount entry type ENTRY TYPE
[JOB#991]
SSP EDIT
TEXT
Associate DEPT.
CONTENTS
Range/Detail
MRS
default
DISABLE/ENABLE ENABLE
DISABLE/ENABLE ENABLE
DISABLE/ENABLE ENABLE
Base Q’ty
BASE QTY
DISABLE/ENABLE ENABLE
MINIMUM
STOCK
MINIMUM
STOCK
DISABLE/ENABLE ENABLE
Price shift
PRICE SHIFT
DISABLE/ENABLE ENABLE
Entry of zero price ZERO OF
in Price shift 1
PRICE1
DISABLE/ENABLE ENABLE
SSP#
SSP No. Entry
Entry of zero price ZERO OF
in Price shift 2
PRICE2
DISABLE/ENABLE ENABLE
(STEP#)
SSP DATA
Entry of zero price ZERO OF
in Price shift 3
PRICE3
DISABLE/ENABLE ENABLE
Entry of zero price ZERO OF
in Price shift 4
PRICE4
DISABLE/ENABLE ENABLE
[JOB#992]
SSP ALL CLEAR
Entry of zero price ZERO OF
in Price shift 5
PRICE5
DISABLE/ENABLE ENABLE
Entry of zero price ZERO OF
in Price shift 6
PRICE6
DISABLE/ENABLE ENABLE
Coupon object
PLU
DISABLE/ENABLE ENABLE
Message
ARE YOU SURE ?
CONTENTS
Yes / No
[JOB#993]
SSP IND. CLEAR
Message
SSP#
CONTENTS
SSP No. Entry
12.MAINTENANCE DATA RESTRICTION BY
ACCOUNT [JOB#850]
PLU/UPC
Item
(text)
Range/Detail
MRS
default
COUPON
OBJECT
Menu type
MENU TYPE
DISABLE/ENABLE ENABLE
Table No.
LINK TBL#
DISABLE/ENABLE ENABLE
Mix&Match table
No.
MIX&MATCH
TBL#
DISABLE/ENABLE ENABLE
Condiment table
No.
CONDIMENT
TBL#
DISABLE/ENABLE ENABLE
Tare table No.
TARE TBL#
DISABLE/ENABLE ENABLE
Condiment type
CONDIMENT
TYPE
DISABLE/ENABLE ENABLE
Condiment entry
to menu item
CONDIMENT
DISABLE/ENABLE ENABLE
Auto combo
object
AUTO COMBO
OBJECT
DISABLE/ENABLE ENABLE
Auto Combo No.
AUTO COMBO
No.
DISABLE/ENABLE ENABLE
Unit price1
PRICE 1
DISABLE/ENABLE ENABLE
Unit price2
PRICE 2
DISABLE/ENABLE ENABLE
Scale
SCALE
DISABLE/ENABLE ENABLE
TAXABLE 1
DISABLE/ENABLE ENABLE
Unit price3
PRICE 3
DISABLE/ENABLE ENABLE
Taxable 1
Unit price4
PRICE 4
DISABLE/ENABLE ENABLE
Taxable 2
TAXABLE 2
DISABLE/ENABLE ENABLE
Unit price5
PRICE 5
DISABLE/ENABLE ENABLE
Taxable 3
TAXABLE 3
DISABLE/ENABLE ENABLE
Unit price6
PRICE 6
DISABLE/ENABLE ENABLE
Taxable 4
TAXABLE 4
DISABLE/ENABLE ENABLE
TAXABLE 5
DISABLE/ENABLE ENABLE
Name for price1
NAME1
DISABLE/ENABLE ENABLE
Taxable 5
Name for price2
NAME2
DISABLE/ENABLE ENABLE
FS/CASH BNF
DISABLE/ENABLE ENABLE
Name for price3
NAME3
DISABLE/ENABLE ENABLE
Food Stampable/
Cash Benefit
Name for price4
NAME4
DISABLE/ENABLE ENABLE
Group discount
GROUP
DISCOUNT
DISABLE/ENABLE ENABLE
Name for price5
NAME5
DISABLE/ENABLE ENABLE
Age limitation
NAME6
DISABLE/ENABLE ENABLE
AGE
LIMITATION
DISABLE/ENABLE ENABLE
Name for price6
KP Text for price1
KP TEXT1
DISABLE/ENABLE ENABLE
PLU grouping1
GROUP1
DISABLE/ENABLE ENABLE
KP Text for price2
KP TEXT2
DISABLE/ENABLE ENABLE
PLU grouping2
GROUP2
DISABLE/ENABLE ENABLE
GROUP3
DISABLE/ENABLE ENABLE
KP Text for price3
KP TEXT3
DISABLE/ENABLE ENABLE
PLU grouping3
KP Text for price4
KP TEXT4
DISABLE/ENABLE ENABLE
KP TEXT5
DISABLE/ENABLE ENABLE
PLU priority
Group for Printing
at KP
PRIORITY
GROUP
DISABLE/ENABLE ENABLE
KP Text for price5
KP Text for price6
KP TEXT6
DISABLE/ENABLE ENABLE
Print station
TOUCH KEY
TEXT
DISABLE/ENABLE ENABLE
MODIFY
OUTPUT
DISABLE/ENABLE ENABLE
DISPLAY TEXT
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 32
Item
(text)
Range/Detail
MRS
default
Print station
OUTPUT KP
No.1
DISABLE/ENABLE ENABLE
Print station
OUTPUT KP
No.2
DISABLE/ENABLE ENABLE
OUTPUT KP
No.3
DISABLE/ENABLE ENABLE
Print station
CHIT RECEIPT
DISABLE/ENABLE ENABLE
Repeat Rounds
Registration
REPEAT ROUND DISABLE/ENABLE ENABLE
Print station
(-)
Item
(text)
Range/Detail
MRS
default
Amount
AMOUNT
DISABLE/ENABLE ENABLE
Text
TEXT
DISABLE/ENABLE ENABLE
Sign
SIGN
DISABLE/ENABLE ENABLE
Taxable 1
TAXABLE1
DISABLE/ENABLE ENABLE
Taxable 2
TAXABLE2
DISABLE/ENABLE ENABLE
Taxable 3
TAXABLE3
DISABLE/ENABLE ENABLE
Taxable 4
TAXABLE4
DISABLE/ENABLE ENABLE
Taxable 5
TAXABLE5
DISABLE/ENABLE ENABLE
Doughnut Exempt DOUGHNUT
object
EXEMPT
DISABLE/ENABLE ENABLE
Key Data Entry
Number
DATA ENT.JOB#
DISABLE/ENABLE ENABLE
Food Stampable/
Cash Benefit
FS/CASH BNF
DISABLE/ENABLE ENABLE
NON-Accessed
Record delete
function
NON-ACCESS
DISABLE/ENABLE ENABLE
Group discount
GR.DISC.
DISABLE/ENABLE ENABLE
HALO
HALO
DISABLE/ENABLE ENABLE
Entry type
ENTRY TYPE
DISABLE/ENABLE ENABLE
Entry allowed in
REG mode
ENTRY IN REG
DISABLE/ENABLE ENABLE
Key Data Entry
Number
DATA ENT.JOB#
DISABLE/ENABLE ENABLE
Coupon Table
PLU1
DISABLE/ENABLE ENABLE
Coupon Table
PLU2
DISABLE/ENABLE ENABLE
Coupon Table
PLU3
DISABLE/ENABLE ENABLE
Coupon Table
PLU4
DISABLE/ENABLE ENABLE
Coupon Table
PLU5
DISABLE/ENABLE ENABLE
Coupon Table
PLU6
DISABLE/ENABLE ENABLE
Coupon Table
PLU7
DISABLE/ENABLE ENABLE
Coupon Table
PLU8
DISABLE/ENABLE ENABLE
Coupon Table
PLU9
DISABLE/ENABLE ENABLE
PLU OTHER PROGRAMMING
Item
(text)
Range/Detail
MRS
CONDIMENT
TABLES
CONDIMENT
TABLE
LINK PLU/UPC
TABLES
LINK PLU TABLE DISABLE/ENABLE ENABLE
MIX & MATCH
TABLES
MIX&MATCH
PLU MENU KEYS PLU MENU KEY
DISABLE/ENABLE ENABLE
DISABLE/ENABLE ENABLE
DISABLE/ENABLE ENABLE
COMBO MEAL TABLES
Item
(text)
Range/Detail
MRS
COMBO MEAL
title
COMBO TITLE
DISABLE/ENABLE ENABLE
Coupon Table
PLU10
DISABLE/ENABLE ENABLE
COMBO KP text
KP
DISABLE/ENABLE ENABLE
Coupon Table
PLU11
DISABLE/ENABLE ENABLE
Condiment table
No.
CONDIMENT
TBL#
DISABLE/ENABLE ENABLE
Coupon Table
PLU12
DISABLE/ENABLE ENABLE
Condiment entry
to menu item
CONDIMENT
DISABLE/ENABLE ENABLE
Coupon Table
PLU13
DISABLE/ENABLE ENABLE
Coupon Table
PLU14
DISABLE/ENABLE ENABLE
Coupon Table
PLU15
DISABLE/ENABLE ENABLE
Coupon Table
PLU16
DISABLE/ENABLE ENABLE
Coupon Table
PLU17
DISABLE/ENABLE ENABLE
Coupon Table
PLU18
DISABLE/ENABLE ENABLE
Coupon Table
PLU19
DISABLE/ENABLE ENABLE
Coupon Table
PLU20
DISABLE/ENABLE ENABLE
PLU priority
Group for Printing
at KP
Print station
PRIORITY GR.
MODIFY OUTPUT
DISABLE/ENABLE ENABLE
DISABLE/ENABLE ENABLE
Print station
OUTPUT KP
No.1
DISABLE/ENABLE ENABLE
Print station
OUTPUT KP
No.2
DISABLE/ENABLE ENABLE
Print station
OUTPUT KP
No.3
DISABLE/ENABLE ENABLE
Print station
CHIT RECEIPT
DISABLE/ENABLE ENABLE
Key Data Entry
Number
DATA ENT.JOB#
DISABLE/ENABLE ENABLE
ASSOCIATED
PLU CODE
COMBO PLU#
DISABLE/ENABLE ENABLE
UNIT PRICE OF
CODE
PRICE1
DISABLE/ENABLE ENABLE
2’nd PRICE OF
CODE
PRICE2
DISABLE/ENABLE ENABLE
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 33
%
Item
(text)
Range/Detail
MRS
default
Rate
RATE
DISABLE/ENABLE ENABLE
Text
TEXT
DISABLE/ENABLE ENABLE
Sign
SIGN
DISABLE/ENABLE ENABLE
Taxable 1
TAXABLE1
DISABLE/ENABLE ENABLE
Taxable 2
TAXABLE2
DISABLE/ENABLE ENABLE
Taxable 3
TAXABLE3
DISABLE/ENABLE ENABLE
Taxable 4
TAXABLE4
DISABLE/ENABLE ENABLE
Taxable 5
TAXABLE5
DISABLE/ENABLE ENABLE
Food Stampable/
Cash Benefit
FS/CASH BNF
DISABLE/ENABLE ENABLE
Group discount
GR.DISC.
DISABLE/ENABLE ENABLE
%HALO
%HALO
DISABLE/ENABLE ENABLE
Entry type
ENTRY TYPE
DISABLE/ENABLE ENABLE
Entry allowed in
REG mode
ENTRY IN REG
DISABLE/ENABLE ENABLE
Key Data Entry
Number
DATA ENT.JOB#
DISABLE/ENABLE ENABLE
Percent Table
PLU1
DISABLE/ENABLE ENABLE
Percent Table
PLU2
DISABLE/ENABLE ENABLE
Percent Table
PLU3
DISABLE/ENABLE ENABLE
Percent Table
PLU4
DISABLE/ENABLE ENABLE
Percent Table
PLU5
DISABLE/ENABLE ENABLE
Percent Table
PLU6
DISABLE/ENABLE ENABLE
Percent Table
PLU7
DISABLE/ENABLE ENABLE
Percent Table
PLU8
DISABLE/ENABLE ENABLE
Percent Table
PLU9
DISABLE/ENABLE ENABLE
Percent Table
PLU10
DISABLE/ENABLE ENABLE
Percent Table
PLU11
DISABLE/ENABLE ENABLE
Percent Table
PLU12
DISABLE/ENABLE ENABLE
Percent Table
PLU13
DISABLE/ENABLE ENABLE
Percent Table
PLU14
DISABLE/ENABLE ENABLE
Percent Table
PLU15
DISABLE/ENABLE ENABLE
Percent Table
PLU16
DISABLE/ENABLE ENABLE
Percent Table
PLU17
DISABLE/ENABLE ENABLE
Percent Table
PLU18
DISABLE/ENABLE ENABLE
Percent Table
PLU19
DISABLE/ENABLE ENABLE
Percent Table
PLU20
DISABLE/ENABLE ENABLE
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SETTING”)
3 – 34
CHAPTER 4. SRV MODE PROGRAMMING (“IRC SETTING”)
1. MANUAL CLEAR AND RESET
[1 SATELLITE]
DISPLAY: Setting screen
This operation clears only the work memory for inline operations.
The program memory for inline operations remained unchanged even
after the resetting here is performed. Inline communications can still be
achieved.
Before trying to perform inline setup, configure a journal printer and
review output for errors after completing IRC setup.
TERMINAL SETTING
1 SATELLITE
2 MASTER
3 BACKUP MASTER
4 STD. WITH IRC
5 STAND ALONE
DISPLAY: SRV mode screen
SRV
1 READING
2 SETTING
3 IRC SETTING
4 DOWN LOAD
5 DIAGNOSTIC
PREV.
NEXT
PREV. NEXT
LIST
P DOWN
$
SATELLITE
IP ADDRESS 1
IP ADDRESS 2
IP ADDRESS 3
IP ADDRESS 4
PLU/UPC
PLU/UPC STOCK
GLU
POSITIVE
LIST P DOWN
Select “3 IRC SETTING” and press the ENTER key.
$
DISPLAY: IRC SETTING item selection screen
IRC SETTING
1 TERMINAL SETTING
2 IRC RESET
PREV. NEXT
192
168
000
000
CENTRALIZED
CENTRALIZED
CENTRALIZED
CENTRALIZED
LIST
P DOWN
Select the item to be changed and press the ENTER key.
The setting content is described below.
Set Up List
DISPLAY
TEXT
PREV. NEXT
LIST
P DOWN
Select “2 IRC RESET” and press the ENTER key.
$
CONTENTS
SELECT ITEM
MRS
IP ADDRESS 1 Terminal number 1
000-254
192
IP ADDRESS 2 Terminal number 2
000-254
168
IP ADDRESS 3 Terminal number 3
000-254
000
001-254
000
IP ADDRESS 4 Terminal number 4
Manual clear job is executed.
PLU/UPC
PLU/UPC
CENTRALIZED CENTRALIZED
PLU/U PC
STOCK
PLU/UPC stock
CENTRALIZED CENTRALIZED
GLU
GLU system
CENTRALIZED CENTRALIZED
POSITIVE
POSITIVE#
system
CENTRALIZED CENTRALIZED
NEGATIVE
NEGATIVE#
system
CENTRALIZED CENTRALIZED
BACKUP
MASTER
B a cku p m a s t e r
function
INDIVIDUAL
2. [1 TERMINAL SETTING]
INDIVIDUAL
DISPLAY: Setting item selection screen
IRC SET UP
1 TERMINAL SETTING
2 IRC RESET
PREV. NEXT
LIST
INDIVIDUAL
P DOWN
Select “1 TERMINAL SETTING” and press the ENTER key.
The contents of setting are shown in the table below.
Note: Please set up satellite first, because downloading of inline presets is performed after master setup completion.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“IRC SETTING”)
4–1
INDIVIDUAL
INDIVIDUAL
EXIST
NOT
NOT
Entry [TERMINAL NO.] WINDOW.
Entry [TERMINAL NO.] WINDOW and [MASTER LIST] WINDOW.
3The POS is changed from standalone POS to inline satellite POS.
3The POS is changed from standalone POS to inline master POS.
SRV#902 a) is “1” (Inline exist.)
SRV#920 d) is “1” (This POS is satellite.)
SRV#902 a) is “1” (Inline exist.)
SRV#920 d) is “2” (This POS is master.)
(PRESETTING OF TERMINAL NO./GLU SYSTEM/Etc.*) and (PRESETTING OF BACKUP MASTER) are acted.
(PRESETTING OF TERMINAL NO./GLU SYSTEM/Etc.* ) and (PRESETTING OF BACKUP MASTER) are acted.
* Please refer to Set Up List.
* Please refer to Set Up List.
(INLINE RAM CLEAR) is acted.
(INLINE FILES for Satellite) are created.
(PRESETTING OF MASTER LIST.) is acted.
(INLINE FILES for Master) are created.
(INLINE RAM CLEAR) is acted.
(DOWN-LOADING OF INLINE PRESETS.) is acted.
[2 MASTER]
DISPLAY: Setting screen
[3 BACKUP MASTER]
TERMINAL SETTING
1 SATELLITE
2 MASTER
3 BACKUP MASTER
4 STD. WITH IRC
5 STAND ALONE
PREV. NEXT
DISPLAY: Setting screen
TERMINAL SETTING
1 SATELLITE
2 MASTER
3 BACKUP MASTER
4 STD. WITH IRC
5 STAND ALONE
LIST
P DOWN
$
PREV. NEXT
MASTER
IP ADDRESS 1
IP ADDRESS 2
IP ADDRESS 3
IP ADDRESS 4
PLU/UPC
PLU/UPC STOCK
GLU
POSITIVE
PREV. NEXT
BACKUP MASTER
IP ADDRESS 1
IP ADDRESS 2
IP ADDRESS 3
IP ADDRESS 4
PLU/UPC
PLU/UPC STOCK
GLU
POSITIVE
192
168
000
000
CENTRALIZED
CENTRALIZED
CENTRALIZED
CENTRALIZED
P DOWN
PREV. NEXT
Select the item to be changed and press the ENTER key.
The setting content is described below.
LIST
P DOWN
Select the item to be changed and press the ENTER key.
Set Up List
DISPLAY TEXT
P DOWN
$
192
168
000
000
CENTRALIZED
CENTRALIZED
CENTRALIZED
CENTRALIZED
LIST
LIST
The setting content is described below.
CONTENTS
SELECT ITEM
MRS
IP ADDRESS 1 Terminal number 1
000-254
192
IP ADDRESS 2 Terminal number 2
000-254
168
IP ADDRESS 3 Terminal number 3
000-254
000
IP ADDRESS 4 Terminal number 4
001-254
000
Set Up List
DISPLAY
TEXT
PLU/UPC
PLU/UPC system CENTRALIZED CENTRALIZED
PLU/U PC
STOCK
PLU/UPC stock
CENTRALIZED CENTRALIZED
GLU
GLU system
CENTRALIZED CENTRALIZED
POSITIVE
POSITIVE#
system
CENTRALIZED CENTRALIZED
NEGATIVE
NEGATIVE#
system
CENTRALIZED CENTRALIZED
BACKUP
MASTER
B a c ku p m a s t e r
function
INDIVIDUAL
CONTENTS
SELECT ITEM
MRS
IP ADDRESS 1 Terminal number 1
000-254
192
IP ADDRESS 2 Terminal number 2
000-254
168
IP ADDRESS 3 Terminal number 3
000-254
000
IP ADDRESS 4 Terminal number 4
001-254
000
PLU/UPC
PLU/UPC system CENTRALIZED CENTRALIZED
PLU/U PC
STOCK
PLU/UPC stock
CENTRALIZED CENTRALIZED
GLU
GLU system
CENTRALIZED CENTRALIZED
POSITIVE
POSITIVE#
system
CENTRALIZED CENTRALIZED
NEGATIVE
NEGATIVE#
system
CENTRALIZED CENTRALIZED
INDIVIDUAL
INDIVIDUAL
INDIVIDUAL
INDIVIDUAL
INDIVIDUAL
INDIVIDUAL
INDIVIDUAL
EXIST
NOT
NOT
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“IRC SETTING”)
4–2
INDIVIDUAL
INDIVIDUAL
Entry [TERMINAL NO.] WINDOW.
3The POS is changed from standalone POS to inline satellite POS.
SRV#902 a) is “1” (Inline exist.)
SRV#920 d) is “3” (This POS is back up master.)
(PRESETTING OF TERMINAL NO./GLU SYSTEM/Etc. *) are acted.
(INLINE FILES for Backup master) are created.
* Please refer to Set Up List.
(INLINE RAM CLEAR) is acted.
[4 STD. WITH IRC]
DISPLAY: Setting screen
TERMINAL SETTING
1 SATELLITE
2 MASTER
3 BACKUP MASTER
4 STD. WITH IRC
5 STAND ALONE
PREV. NEXT
LIST
P DOWN
Select the item to be changed and press the ENTER key.
The setting content is described below.
Set Up List
DISPLAY TEXT
SELECT ITEM
MRS
IP ADDRESS 1 Terminal number 1
CONTENTS
000-254
192
IP ADDRESS 2 Terminal number 2
000-254
168
IP ADDRESS 3 Terminal number 3
000-254
000
IP ADDRESS 4 Terminal number 4
001-254
000
Entry [TERMINAL NO.] WINDOW.
3The POS is changed from stand-alone POS to standalone with IRC
POS.
SRV#902 a) is “1” (Inline exist.)
SRV#920 d) is “0” (This POS is standalone.)
(PRESETTING OF TERMINAL NO.) is acted.
[5 STAND ALONE]
Used to restore to a stand alone machine.
TERMINAL SETTING
1 SATELLITE
2 MASTER
3 BACKUP MASTER
4 STD. WITH IRC
5 STAND ALONE
PREV. NEXT
LIST
P DOWN
Entry [TERMINAL NO.] WINDOW.
3The POS is changed from inline POS to standalone POS.
SRV#902 a) is “0” (Inline not exist.)
SRV#920 d) is “0” (This POS is standalone.)
(PRESETTING OF TERMINAL NO.) is cleared.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“IRC SETTING”)
4–3
CHAPTER 5. SRV MODE PROGRAMMING (“DOWN LOAD”)
The preset data of master machine is downloaded in satellite machines.
After IRC SETUP, using this setting procedure, download the setting
data from the master.
DISPLAY: SRV mode screen
SRV
1 READING
2 SETTING
3 IRC SET UP
4 DOWN LOAD
5 DIAGNOSTIC
PREV. NEXT
LIST
P DOWN
Select “4 DOWN LOAD” and press the ENTER key.
$
DISPLAY: DOWN LOAD item selection screen
DOWN LOAD
1 SRV PARAMETER
2 FREE KEY
PREV. NEXT
LIST
P DOWN
[1 SRV PARAMETER]-[JOB#800]
SRV PARAMETER
Including the machine parameter relating to in-line operations.
(“#902”, “#920-d:TERMINAL”, and “#921-d:MACHINE LOCATION” are
not down-loaded.)
Mode secret code preset
Maintenance Restriction table
[2 FREE KEY]-[JOB#850]
FREE KEY LAYOUT
Home
/Function Menu table
Key Name/Attribute table
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“DOWN LOAD”)
5–1
CHAPTER 6. SRV MODE PROGRAMMING (“SD CARD MODE”)
1. MENU LIST
In ECR, SD CARD is the tool for providing the each data of ECR to by
offline and saving/loading ALL RAM DATA at ECR.
MODE
Target SD Card : SD CARD producted by “SanDisk”
(Memory size : 256MB to 2GB)
1-8
9 SD CRAD MODE (*1)
Note: This model dose not support the SD CARD which can be
inserted to the card slot of ECR by using any adapters.
(“Mini SD”, “Micro SD”...)
SAVING
SAVE ONLY
SALES DATA
EJ DATA
T- LOG DATA
PROGRAMMING DATA
General attention to use SD CARD :
If AC POWER is removed or turned off whenECR is accessing
the SD CARD,the contents in SD CARD may be corrupted.
SAVE & CLEAR
EJ DATA
T- LOG DATA
List of the data on SD Card:
Kinds of data
Purpose
Direction of data
All RAM Data
DATA BACKUP
ECR --> (SD)
ECR <-- (SD)
Programming
Data
For using on PC
ECR --- (SD) -->PC
ECR <-- (SD) --- PC
Sales Data
For using on PC
(Daily and Term)
ECR --- (SD) -->PC
EJ Data
For using on PC
ECR --- (SD) -->PC
T - LOG Data
For using on PC
ECR --- (SD) -->PC
LOADING
PROGRAMMING DATA
FOLDER CONTROL
FOLDER CODE
FOLDER CREATE
FORMATTING
SRV MODE
1-6
7 SD CARD MODE
SAVING
SAVE ONLY
SALES DATA
EJ DATA
T- LOG DATA
PROGRAMMING DATA
ALL RAM DATA
SAVE & CLEAR
EJ DATA
T- LOG DATA
LOADING
PROGRAMMING DATA
ALL RAM DATA
FOLDER CONTROL
FOLDER NAME
FOLDER CREATE
FOLDER READING (*2)
FORMATTING
(*1) PGM2-SETTING-PERSONNEL-CLERK-SD CARD MODE :
ENABLE/DISABLE
(*2) Only 100 folder is displayed.
2. FILE LIST ON SD CARD
The data is saved in SD card as the files that have the two following
kinds.
*.FDS
*.SDA, *.002,*.003,*.004 [“*” is a same name for each file.]
And, the “*.REC” files are created to control the files in SD card.
These files are used only for the “SD CARD FUNCTION” of this model.
(They cannot be used for any function except the “SD CARD
FUNCTION”.)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–1
3. LIST OF FOLDER
SHARP
ECR
xxxxxxxx
(USER FOLDER : You can setting this Folder code.)
("x" is used only numeric characters.)
ALL
(ALL RAM BACKUP)
PROGRAM
(Programming Data)
SALES
(Sales Data) (*1)
...<Sub-Folders> (*2)
(Electronic Journal) (*1)
EJ
...<Sub-Folders> (*2)
(T-LOG data) (*1)
TLOG
...<Sub-Folders> (*2)
(for ONLINE/MWS Upload Function)
ONLINE
EJ
TLOG
(USER FOLDER : You can program this Folder code.)
("x" can be used numeric characters.)
xxxxxxxx
(*1) New SUB-Folders are created in this folder when the data writing job is operated.
(*2) <Sub-Folders> : The sub folders of each folder (SALES/EJ/TLOG) are shown below.
SALES
(or EJ)
(or TLOG)
001
001
002
:
050
051
051
052
:
100
101
:
901
951
UP-810F/820N/820F (U)
951
952
:
999
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–2
4. SALES DATA (SAVING) (PGM2 & SRV MODE)
All sales data (Daily and term) are saved in SD card.
Maximum 999 times data is kept in SD Card when the SD memory is
not full.
The action is as below.
1) After reading the information of the current sub-folder from
“SRECORD.REC” file, ECR creates the new sub-folder under the
folder for “Sales Data”.
Its folder is named ASCII Character that is indicated the number of
sales data in SD Card.
(Example: “001”, “002”, “003”,...... )
2) Save the below data in new sub-folder that is created by previous
step.
FileName
(8digits)
File/Table
No.(*1)
Field (*1)
1
Date,Time
MTIMTBL
D0
Table
2
Dept file
DEPT
01
01D00000 (Label, Daily, Term, Save daily, Consol)
3
Dept file
DEPTPRS
01
B0000000 (Label, Preset, Price, Text)
4
Dept Discount file
DISCSAL
02
01D00000 (Label, Daily, Term, Save daily, Consol)
5
PLU/UPC file
PLU
11
01D001D001D001D001D
(Label, Daily, Term, Save daily, consol, Combo Daily, Combo Term,
Combo Save Daily, Combo consol, Waste Daily, Waste Term,
Waste Save Daily, Waste consol, Refund Daily, Refund Term,
Refund Save Daily, Refund consol, Coupon Daily, Coupon Term,
Coupon Save Daily, Coupon consol)
6
PLU/UPC file
PLUPRS
11
B0000000 (Label, Preset, Price, Text)
7
Transaction file
TRANS
31
81D00000 (Label, Daily, Term, Save daily, Consol)
8
Dynamic UPC file
DUPC
32
01D0000001D001D001D
(Label, Daily, Term, Save Daily, consol, Waste Daily, Waste Term,
Waste Save Daily, Waste consol,
Refund Daily, Refund Term,
Refund Save Daily, Refund consol,
Coupon Daily, Coupon Term,
Coupon Save Daily, Coupon consol)
9
Dynamic UPC file
DUPCPRS
32
B0000000 (Label, Preset, Price, Text)
10
Server preset file
CLKDATA
51
90000000 (Label, Preset, Text)
11
Server Transaction file
12
Total Server Transaction file
CLKSAL
52
81D00000 (Label, Daily, Term, Save daily, Consol)
CLKSALTL
54
81000000 (Label, Daily)
HOURLY
61
81500000 (Label, Daily, Save daily, Consol)
DNET
71
81000000 (Label, Sales)
13
Hourly file
14
Daily Net file
15
Daily net Consol. file
DNETCS
79
80100000 (Label, Sales)
16
Acct bal offline
ACTBAL
7F
80000000 (Sales)
17
T-log file
TLOG
88
80000000 (Label, Data)
18
GLU file
GLU
91
80000000 (Label, Data)
19
Closed GLU file
CGLU
92
C0000000 (Label, Data, Amount)
20
Function Text
FUNCTXT
A2
80000000 (Label, Text)
21
Capture Job Sales File
CPTSALE
A9
80000000 (Label, Data)
22
Customer Sales File
CSTSALE
AF
80000000 (Label, Data)
23
Current GT
CURTGT
C4
Table
24
Consol. GT
CNSLGT
C6
Table
25
Current Z Counter
CURTZ
C8
Table
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–3
6) In case of “SAVE & CLEAR” job, Create (or Update) the “STATUS.REC” file in the folder for “EJ for ONINE” when all files are
saved completely.
3) Create the “STATUS.REC” file in new sub-folder when all files are
saved completely.
File Name
Status information
File Name
STATUS . REC
Status information
4) Update the “SRECORD.REC” file for changing the structure of
sub-folder.
7) In case of “SAVE & CLEAR” job, after saving EJ data to SD card,
the EJ data in ECR is eresed.
File Name
Record structure
STATUS.REC
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”.
Details of “File No.”, “Table No.” and “Field” are described in
“ONLINE SPECIFICATION”.
SRECORD. REC
(*1) The contents of each file are same as the communication data
of “ONLINE FUNCTION”.
Details of “File No.” and “Table No.” are described in “ONLINE
SPECIFICATION”.
(*2) “READ” is written by ONLINE JOB “UPLOAD EJ DATA from SD
CARD”.
Note:
Note: Each files are used only for the software on PC.
• If the folder for “Electronic Journal” does not exist in SD memory
card, error will result.
[“NO FOLDER” ERROR]
5. EJ DATA (SAVING)(PGM2 &SRV MODE)
• If the folder for “EJ for ONLINE” does not exist in SD memory card,
error will result.
[“NO FOLDER” ERROR]
Electronic journal data is saved in SD card.
Maximum 999 times data is kept in SD Card when the SD memory is
not full.
• SRV#988_B : Control Character is converted to SPACE when EJ
data is saved in SD card
Note: In case of “SAVE & CLEAR”, after saving EJ data to SD card, the
EJ data in ECR is eresed.
YES/NO = 2/0
Control Character : 0x00 - 0x1F, 0xFE, 0xFF
Space Character : 0x20
The action is as below.
1) After reading the information of the current sub-folder in
“SRECORD.REC” file, ECR creates the new sub-folder under the
folder for “Electronic Journal”.
Its folder is named ASCII Character that is indicated the number of
sales data in SD Card.
(Example: “001”, “002”, “003”,...... )
6. T-LOG DATA (SAVING)
(PGM2 & SRV MODE)
T-LOG data is saved in SD card.
2) Save the below data in new sub-folder that is created above step.
File Name
EJ Data
File/Table
No. (*1)
EJFILE .FDS
EJFILE .SDA
Maximum 999 times data is kept in SD Card when the SD memory is
not full.
Field (*1)
Note: In case of “SAVE & CLEAR”, after saving T-LOG data to SD card,
the T-LOG data in ECR is eresed.
A0
The action is as below.
3) Create the “STATUS.REC” file in new sub-folder when all files are
saved completely.
1) After reading the information of the current sub-folder in
“SRECORD.REC” file, ECR creates the new sub-folder under the
folder for “T-LOG data”.
Its folder is named ASCII Character that is indicated the number of
sales data in SD Card.
(Example : “001”, “002”, “003”,...... )
File Name
Status information
STATUS . REC
4) Update the “SRECORD.REC” file for changing the structure of subfolder.
2) Save the below data in new sub-folder that is created above step.
File Name
File Name
Record structure
T-LOG Data
SRECORD.REC
5) In case of “SAVE & CLEAR” job, after saving EJ data to SD card,
the EJ data in ECR is eresed.
(If “READ” is written in “STATUS.REC” file, current EJ file in SD card
is deleted and new EJ file is created. (*2)
In the other cases, new EJ records are added to current EJ file data
in SD card.)
File Name
EJ Data
EJFILE .FDS
EJFILE .SDA
File/Table
No. (*1)
TLOGFILE. FDS
TLOGFILE. SDA
Field ( *1)
88
3) Create the “STATUS.REC” file in new sub-folder when all files are
saved completely.
File Name
Status information
STATUS . REC
4) Update the “SRECORD.REC” file for changing the structure of subfolder.
Field (*1)
File Name
A0
Record structure
UP-810F/820N/820F (U)
File/Table
No. (*1)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–4
SRECORD. REC
7) In case of “SAVE & CLEAR” job, after saving T-LOG data to SD card
the T-LOG data in ECR is erased.
5) In case of “SAVE & CLEAR” job, after saving T-LOG data to SD card
the T-LOG data in ECR is erased.
(If “READ” is written in “STATUS.REC” file, current T-LOG file in SD
card is deleted and new T-LOG file is created. ( *2)
In the other cases, new T-LOG records are added to current T-LOG
file data in SD card.)
File/Table
No. (*1)
File Name
T-LOG Data
TLOGFILE. FDS
TLOGFILE. SDA
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”.
Details of “File No.” and “Table No.” are described in “ONLINE
SPECIFICATION”.
(*2) “READ” is written by ONLINE JOB “UPLOAD T-LOG DATA from
SD CARD”.
Field ( *1)
88
Note:
• If the folder for “T-LOG Data” does not exist in SD memory card,
this job is inhibited.
[“NO FOLDER” ERROR]
6) In case of “SAVE & CLEAR” job, Create (or Update) the “STATUS.REC” file in the folder for “T-LOG for ONLINE” when all files
are saved completely.
• If the folder for “T-LOG for ONLINE” does not exist in SD memory
card, this job is inhibited.
[“NO FOLDER” ERROR]
File Name
Status information
STATUS . REC
7. PROGRAMMING DATA
(SAVING / LOADING) (PGM2 & SRV MODE)
FileName
Save Field ( *1)
File/Table
No.(*1)
1
Dept file
DEPTDT
01
B0000000 (Label, Preset, Price, Text)
2
PLU/UPC file
PLUDT
11
F00010001 (Label, Preset, Flag, Price, Text, Key Text, KP Text)
3
Link PLU file
LNKPLUDT
12
80000000 (Label, Preset)
4
Condiment PLU file
CONDMDT
14
C0000000 (Label, Preset, Text)
5
Mix & Match table file
PROMDT
15
90000000 (Label, Preset, Text)
6
Dynamic UPC file
DUPCDT
32
B00010001 (Label, Preset, Price, Text, Key Text, KP Text)
7
PLU/UPC PGM Pick up file
PKUPPDT
34
80000000 (Label)
8
PLU/UPC X/Z Pick up file
PKUPXDT
36
80000000 (Label)
9
Dynamic UPC X/Z Pick up file
10
Server preset file
DPKUPXDT
37
80000000 (Label)
CLKDT
51
90000000 (Label, Preset, Text)
11
Manager preset file
12
Scroll Message for Pole Display
MGRDT
5A
80000000 (Label, Preset)
SMSGPLDT
7B
80000000 (Label, Message)
13
Logo Text
LOGODT
A1
80000000 (Label, Text)
14
Function Text
FUNCDT
A2
80000000 (Label, Text)
15
Dept Group Text
DEPTGPDT
A3
80000000 (Label, Text)
16
Sort Group Text
SGROUPDT
A4
80000000 (Label, Text)
17
Currency Descriptor Text File
CDSCRPDT
A6
80000000 (Label, Text)
18
Capture Key File
CPTKEYDT
A7
90000000 (Label, Preset, Text)
19
Capture Job Preset File
CPTJOBDT
A8
90000000 (Label, Preset, Text)
20
VP Text
VPTXTDT
AA
80000000 (Label, Text)
21
PLU Menu File
PLMNKYDT
AB
D0000000 (Label, Preset1, Preset2, Text)
22
Combo File
CMBMLDT
AC
900000001 (Label, Preset, Text, Key Text, KP Text)
23
Customer File
CUSTMDT
AE
90000000 (Label, Preset, Text)
24
Macro Key Table File
MACRODT
B0
80000000 (Label, Preset)
25
KP Preset File
KPPRESDT
B1
90000000 (Label, Preset, Text)
26
Direct Key table
DIRKEYDT
B3
80000000 (Label, Preset)
27
Scale table
SCLKEYDT
B4
80000000 (Label, Preset)
28
Auto Key Table
AUTKEYDT
B5
80000000 (Label, Preset)
29
Stack report table
STCRPTDT
B6
80000000 (Label, Preset)
30
Message File
MSGDT
BA
90000000 (Label, Preset, Text)
31
Positive Number Preset
POSITIDT
BB
80000000 (Label, Preset)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–5
32
Negative Number Preset
Save Field ( *1)
FileName
File/Table
No.(*1)
NEGATDT
BF
80000000 (Label, Preset)
33
SRV Parameter
SRVPGMTB
C1
Table
34
Mode Secret Code
MDSCRTTB
C2
Table
35
Free Key Table
FREKEYTB
C3
Table
36
Key Attribute Table
KEYATRTB
CE
Table
37
Optional Feature
OPTFERTB
D1
Table
38
Tax Table
TAXTB
D6
Table
39
Tax Q’ty Table
40
Function Preset
TAXQTYTB
D7
Table
FUNCTB
D8
Table
SCANTB
DA
Table
MRESTTB
E1
Table
41
Scanner Preset
42
Maintenance Restriction
43
Non PLU Code Format
NPLUTB
E8
Table
44
GLU Table
GLUTBLTB
E9
Table
45
Job Secret Code
JBSCRTTB
EC
Table
46
Inline preset
INLINETB
F0
Table
47
CAT Preset
48
Logical Device
CATTB
F2
Table
LOGDEVTB
F7
Table
49
Home function menu
HMFNCTB
E0
Table
50
Money
MONEYTB
E2
Table
10.FOLDER CREATE
(*1) The contents of each file are same as the communication data of
“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”.
All data are converted to use at PC.
• \xxxxxxxx is made at a folder “\SHARP\ECR”.
• \ALL, \PROGRAM, \SALES, \EJ, \TLOG and \ONLINE are made at
the folder “\SHARP\ECR\xxxxxxxx”.
Note:
• If the folder for “Programming Data” dose not exist in SD memory
card, this job is inhibited. [“NO FOLDER” ERROR]
• \EJ and \TLOG are made at the folder
“\SHARP\ECR\xxxxxxxx\ONLINE”.
• If there is data of the same file name, data is overwritten.
• The file “MODEL.REC” is made at the folder
“\SHARP\ECR\xxxxxxxx\SALES”,
• Each files are used only for the software on PC.
• The file “SRECORD.REC” “\SHARP\ECR\xxxxxxxx\EJ” and
“\SHARP\ECR\xxxxxxxx\TLOG”.
8. FORMATTING
Note: The file “SRECORD.REC” and “MODEL.REC” are used for control the structure under each folder. Any users do not need to
concern its contents.
This job formats SD card. (It deletes all data on SD card.)
After formatting card, the folder \SHARP\ECR is made at a root directory.
Note: All the data currently written in SD card is erased.
11.ALL RAM DATA
(SAVING / LOADING) (SRV MODE)
9. FOLDER NAME
The below data is saved or loaded. File is set in the folder for “ALL
RAM BACKUP”.
This job programs the Folder Name on SD card.
xxxxxxxx (8 digits Characters* )
File Name
* 0 - 9, A - Z (Capital letter) !#$%&’()-_^`{}~@)
All RAM data
ALL
. SDA
Note:
• When you selected loading All RAM data, you have to service
reset.
• If there is the file that has same file name, data is overwritten .
• In case of “LOADING”, the condition of ECR will return to past condition except Date & Time.
• This file is used only for the purpose of DATA BACKUP at ECR.
Any users do not need to concern its contents.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–6
12.FOLDER READING
13.DISPLAY
P UP ▲
SD CARD
1 SAVING
2 LOADING
3 FOLDER CONTROL
4 FORMATTING
2 LOADING
3 FOLDER CONTROL
<<Key Area>>
<<Key Area>>
4 FOLDER READING
5 FORMATTING
PREV. NEXT LIST P DOWN ▼
SRV
SERVER0001
_
PREV. NEXT LIST P DOWN ▼
SRV
SERVER0001
_
0001
12:34
0001
12:34
MODE TITLE : SRV or PGM2
“4 FOLDER READING” is selected.
JOB NAME
SD in the folder code display.
SALES DATA
P UP ▲
P UP ▲
FOLDER READING
00000001
00000002
00000003
12345678
99999999
ARE YOU SURE ?
+-------------------+
| 1 YES
|
| 2 NO
|
+-------------------+
<<Key Area>>
PREV. NEXT LIST P DOWN ▼
SRV
SERVER0001
_
PREV. NEXT LIST P DOWN ▼
PGM2 SERVER0001
_
0001
12:34
SALES DATA
Folder code is selected.
FOLDER NAME
FOLDER NAME
P UP ▲
SD CARD
1 SAVING
SD in the folder screen to list of display.
00000003
<<Key Area>>
<<Key Area>>
PREV. NEXT LIST P DOWN ▼
PGM2 CLERK0001
_
PREV. NEXT LIST P DOWN ▼
SRV
SERVER0001
_
0001
12:34
P UP ▲
+-------------------+
| PROCESSING..
|
|
|
+-------------------+
P UP ▲
00000003
<<Key Area>>
: moves.
0001
12:34
ERROR MESSAGE
SAVING
The selected code on the display.
The code will be able to set.
P UP ▲
RETRY ?
+-------------------+
| 1 RETRY
|
| 2 ABORT
|
+-------------------+
SD CANCELLED
PREV. NEXT LIST P DOWN ▼
PGM2 SERVER0001
_
Customer Display is not changed.
UP-810F/820N/820F (U)
0001
12:34
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–7
<<Key Area>>
0001
12:34
14.PRINT
The message is printed on JOURNAL only
Print
NOTE
JOB TITLE is printed.
MESSAGE is printed.
(This is Normal End Message.)
(HEADER)
FORMATTING
SD FINAL
(HEADER)
FOLDER CODE
FOLDER NAME
00000001
(HEADER)
FOLDER CREATE
SD FINAL
(HEADER)
SAVE SALES
SD FINAL
(HEADER)
SAVE EJ
SD FINAL
(HEADER)
SAVE T-LOG
SD FINAL
(HEADER)
SAVE PROGRAM
SD FINAL
(HEADER)
SAVE ALL RAM
SD FINAL
(HEADER)
SV & CL EJ
SD FINAL
(HEADER)
SV & CL T-LOG
SD FINAL
(HEADER)
LOADING PROGRAM
SD FINAL
(HEADER)
LOADING ALL RAM
SD FINAL
CARD FULL
ERROR MESSAGE
NO FILE
ERROR MESSAGE
FILE FAILED
ERROR MESSAGE
OVER LIMIT.
ERROR MESSAGE
SD CANCELED
ERROR MESSAGE
POWER OFF
ERROR MESSAGE
NO FOLDER
ERROR MESSAGE
SD ERROR
ERROR MESSAGE
MODEL INVALID
ERROR MESSAGE
CARD PROTECT
ERROR MESSAGE
The MESSAGEs are fixed in ROM.
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–8
15.ERROR MESSAGE LIST
No.
Description
MESSAGE
DISPLAY
PRINT
1
SD JOB Normal End
SD FINAL
—
O
2
SD card is not found
NO CARD
O
—
3
SD card memory is full
CARD FULL
O
O
4
No file exist
NO FILE
O
O
5
File access error (Write protect, or )
FILE FAILED
O
O
6
999 times limitation error (SALES, EJ, T-LOG)
OVER LIMIT.
O
O
7
Operation was canceled by [CANCEL] key
SD CANCELED
O
O
8
Power off was occurred during SD card access
POWER OFF
O
O
Designated folder does not exist
NO FOLDER
O
O
10
9
Model is invalid
MODEL INVALID
O
O
11
Card Protect Error
CARD PROTECT
O
O
12
SD CARD ERROR
(Error except above 2 - 11 ERROR was occurred)
(Folder can not be made)
(File close can not be executed)
(File can not be read)
(File can not be written)
(File can not be deleted)
(SD card memory can not be mounted)
(SD card memory can not be unmounted)
(SD job execution during ONLINE/MWS communication)
SD ERROR
O
O
(O : Used, — : Not used)
UP-810F/820N/820F (U)
SRV MODE PROGRAMMING (“SD CARD MODE”)
6–9
COPYRIGHT ¤ 2008 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Information and Communication Systems Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186, Japan
2008 May Printed in Japan t
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising