Jordan MK70 specs

Jordan MK70 specs
3L/T-2R/S33 Series
Sliding Gate Control Valves
The Mark 70 Series is a line of pneumatically-operated
diaphragm control valves that combine multiple spring
actuators with the precision of Jordan Valve's advanced sliding gate seat for closer control and greater
accuracy.
Jordan's unique sliding gate control valve trim teams
up with pressure, temperature pH, level, or flow controllers for fast response, long term reliability, and high
levels of accuracy on steam, gas, liquid and chemical
services.
Consisting of a modulating disc and stationary plate,
the sliding gate seat components are slotted with
multiple orifices that align to provide the precise flow
needed to maintain the process requirements. The
valve strokes in a fraction of the travel required by
conventional control valves for rapid correction of any
deviation from the process setpoint.
Pneumatic Control Valves
Mark 70 Series
CRN Registration Number Available
This brochure includes the following Series:
•
•
•
MK70PG: a pump governor with its control port
connected to the pump discharge line. The valve
throttles to maintain a constant pump discharge by
controlling the steam flow to the pump.
MK701/702: for higher capacity requirements.
•
Totally enclosed multi-spring actuator –
minimizes deadband and is field reversible without the use of special tools
or additional parts
•
Compact design and simple construction – allows fast, simple installation
and easy maintenance
•
MK707: features an equal percentage flow
characteristic.
•
MK711: a linear control valve in sizes up to 6"
(DN150) with Cv's to 395 (340 Kv)
•
MK74: controls fugitive emissions while reducing
the risks associated with toxic, corrosive, explosive
and high temperature fluids
•
Features
MK76: a low profile, lightweight "on-off" control
valve
Sliding gate seats provide:
—
Straight-through flow for reduced
turbulence and quiet operation
—
Short stroke for fast response and
accurate control
—
Easily interchangeable Cv's
—
Tight shutoff due to overlap of seat
closure area
•
Stem packing is four times deeper then
stem travel – for greater protection
against leakage
Jordan Valve a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Mark 70 Sliding Gate Control Valves
•
MK70: a line of pneumatically-operated diaphragm
control valves that combine multiple spring actuators with the precision of Jordan Valve's advanced
sliding gate for closer control and greater metering
accuracy
Mark 70 Sliding Gate Control Valves
Specifications
Sizes: (note: 1/4" & 3/8" sizes use 1/2" body with
reducers)
• Mark 70/70PG: 1/4" through 2" (DN8 through
DN50)
• Mark 76: 1/4" through 6" (DN8 through DN150)
• Mark 707: 1/2" through 6" (DN15 through
DN150)
• Mark 711: 2-1/2" through 6" (DN65 through
DN150)
Yoke Material: Cast Iron
End Connections
• Threaded (NPT, BSPT, BSPP – through 2"
(DN50) sizes)
• ANSI Flanges (150#, 300#)
• DIN Flanges (PN10/16, PN25/40)
Ranges
• Mark 70/707/711: 3-15, 3-9, 9-15, 6-30 psi
(0,21-1,03; 0,21-0,62; 0,62-1,03; 0,41-2,07
bar)
• Mark 76: on/off – operated with 20 psi (1,4
bar) for 1/2" through 2" sizes (DN15 through
DN50); 50 psi (3,5 bar) for 2-1/2" through 6"
sizes (DN65 through DN150)
• Mark 70PG: consult factory for ranges
Actuator: Steel
Diaphragm: Buna-N (standard to 200°F, 93,3°C)
Stem Packing: spring-loaded Teflon (to 450°F;
232°C); Graphite (to 1200°F; 649°C)
Service: Steam, water, oil, gas, air and chemicals
Shutoff: ANSI Class IV
Body Materials
• Ductile Iron
• Bronze (1/2" – 2"/ DN15 – DN50)
• Carbon Steel (WCB)
• Stainless Steel (CF8M)
Action
• Direct (air signal closes valve)
• Reverse (air signal opens valve)
Trim Materials
• 303SS for CI and DI body valves
• 316SS for SS body valves
Positioner: side or top-mounted positioners are
available to overcome the normal hysteresis for a
control valve and actuator, and to ensure that the
valve stem position is always directly proportional
to the control valve command signal. See the
Positioner section for more details.
Seat Materials
• Jorcote on SST – standard
-2-
Mark 70 Sliding Gate Control Valves
Cv Values and Maximum Allowable Differential Pressure Ratings
•
Mark 70
Flow Coef.
Cv
Maximum Differential Presure
Kv
Valve Size
(DN)
Seat
Material
PSI
BAR
PSI
BAR
PSI
BAR
PSI
BAR
PSI
SST
125
8,6
175
12,1
175
12,1
175
12,1
175
12,1
250
17,2
500
34,5
350
24,1
700
48,3
550
37,9
Std. 35M Actuator
Optional 55M
Actuator
35M w/Positioner
Optional 85M
Actuator
55M w/Positioner
BAR
2.5 or
4.4
2,2 or
3,8
1/2" & 3/4"
(DN15 & 20)
Jorcote
6.4 or
9.5
5,5 or
8,2
1" & 1-1/4"
(DN25 & 32)
SST
100
6,9
150
10,3
150
10,3
150
10,3
150
10,3
Jorcote
150
10,3
300
20,7
215
14,8
425
29,3
350
24,1
15
12,9
1-1/2"
(DN40)
SST
75
5,2
125
8,6
100
6,9
125
8,6
125
8,6
Jorcote
125
8,6
250
17,2
175
12,1
350
24,1
275
19,0
25 or
30
21,5 or
25,8
2"
(DN50)
SST
75
5,2
125
8,6
100
6,9
125
8,6
125
8,6
Jorcote
125
8,6
250
17,2
175
12,1
350
24,1
275
19,0
Based on 45 psi (3,1 bar) to actuator or positioner
•
Mark 76 — Standard Actuator: 1/2" – 2": 506;
2-1/2" – 6" 35M
Flow Coef.
Cv
2.5 or 4.4
6.4 or 9.5
15
2,2 or 3,8
5,5 or 8,2
12,9
Maximum ∆P
Valve Size
(DN)
Seat
Material
PSI
BAR
1/2" & 3/4"
(DN15 & 20)
SST
125
8,6
Jorcote
400
27,6
SST
100
6,9
Jorcote
250
17,2
SST
75
5,2
Jorcote
175
12,1
SST
75
5,2
Jorcote
175
12,1
Kv
1" & 1-1/4"
(DN25 & 32)
1-1/2" (DN40)
25 or 30
21,5 or 25,8
2" (DN50)
85
73,1
2-1/2" (DN65)
Jorcote
100
6,9
130
112
3" (DN80)
Jorcote
100
6,9
200
172
4" (DN100)
Jorcote
75
5,2
395
340
6" (DN150)
Jorcote
75
5,2
•
•
Flow Coef.
Mark 711 — Standard Actuator: 2-1/2" – 3":
55M; 4" – 6" 85M
Flow Coef.
Valve Size
(DN)
Seat
Material
Cv
Kv
85
73
2-1/2" (DN65)
130
112
200
395
Maximum ∆P, PSI*
Standard
w/Positioner
PSI
BAR
PSI
BAR
Jorcote
50
3,5
275
19
3" (DN80)
Jorcote
50
3,5
275
19
172
4" (DN100)
Jorcote
50
3,4
325
22
340
6" (DN150)
Jorcote
50
3,4
225
16
Mark 707 — Standard Actuator: 1/2" – 3/4":
35M; 1" – 2": 55M; 2-1/2" – 6" 85M
Maximum ∆P*
Cv
Kv
Valve Size
(DN)
Seat
Material
Standard
Actuator
PSI
BAR
PSI
BAR
2.5
2,2
1/2" (DN15)
Jorcote
250
17,2
500
34,5
4.4,
6.4 or
9.5
3,8,
5,5 or
8,2
3/4" (DN20)
Jorcote
150
10,3
300
20,7
11.5
9,9
1" (DN25)
SST
100
6,9
175
6,9
Jorcote
150
10,3
300
13,8
13
11,2
1-1/4" (DN32)
22
18,9
1-1/2" (DN40)
34
29,2
2" (DN50)
60
51,6
2-1/2" (DN65)
w/Positioner
SST
100
6,9
175
6,9
Jorcote
150
10,3
300
13,8
SST
100
6,9
150
6,9
Jorcote
150
10,3
150
10,3
SST
100
6,9
150
6,9
Jorcote
150
10,3
150
10,3
Jorcote
80
5,5
275
19,0
80
68,8
3" (DN80)
Jorcote
80
5,5
275
19,0
130
112
4" (DN100)
Jorcote
50
3,5
225
15,5
230
198
6" (DN150)
Jorcote
50
3,5
150
10,3
Low Flow: reduced Cv's/Kv's can be used in any size
valve as long as it is a smaller value than is standard
for that size. In addition, these low flow Cv's/Kv's can be
provided:
* Higher ∆P's available with optional larger actuators
-3-
1.6
0.84
0.42
0.21
0,02
0,008
0,004
0,002
0.08
0.04
0,0008 (N/A in 316SS)
Mark 70 Sliding Gate Control Valves
Maximum Working Pressures & Temperatures
•
Mark 70 & Mark 707 (1/2" – 2") (DN15 – DN50)
Maximum Pressure @ 100°F, PSI/°F
Any
150#
250
DI Body
300#
640
TE
988
TEF
GRAF
170/500
125/650
495/500
450/650
808/500
715/650
Any
150#
17
DI Body
300#
44
TE
68
TEF
GRAF
12/260
9/343
34/260
31/343
56/260
49/343
Packing
BRZ Body
CS Body
150#
300#
TE
150#
300#
TE
225
500
500
285
740
1480
Pressure @ Maximum Temperature, PSI/°F
150/500 325/500 325/500 170/500 600/500 1200/500
150/500 325/500 325/500 125/650 535/650 1075/650
150#
275
SST Body
300#
720
TE
1440
170/500
125/650
480/500
445/650
955/500
890/650
TE
102
150#
19
SST Body
300#
50
TE
99
83/260
74/343
12/260
9/343
33/260
31/343
66/260
61/343
TE
—
150#
275
SST Body
300#
720
TE
—
—
—
170/500
125/650
480/500
445/650
—
—
TE
—
150#
19
SST Body
300#
50
TE
—
—
—
12/260
9/343
33/260
31/343
—
—
Maximum Pressure @ 38°C, BAR/°C
Packing
•
BRZ Body
CS Body
150#
300#
TE
150#
300#
16
34
34
20
51
Pressure @ Maximum Temperature, BAR/°C
10/260
22/260
22/260
12/260
41/260
10/343
22/343
22/343
9/343
37/343
Mark 711 & Mark 707 (2-1/2" – 6") (DN65 – DN150)
Maximum Pressure @ 100°F, PSI/°F
Any
150#
250
DI Body
300#
640
TE
—
TEF
GRAF
170/500
125/650
495/500
450/650
—
—
Packing
BRZ Body
CS Body
150#
300#
TE
150#
300#
—
—
—
285
740
Pressure @ Maximum Temperature, PSI/°F
150/500 325/500
—
170/500 600/500
150/500 325/500
—
125/650 535/650
Maximum Pressure @ 38°C, BAR/°C
Any
150#
17
DI Body
300#
44
TE
—
TEF
GRAF
12/260
9/343
34/260
31/343
—
—
Packing
•
BRZ Body
CS Body
150#
300#
TE
150#
300#
—
—
—
20
51
Pressure @ Maximum Temperature, BAR/°C
10/260
22/260
—
12/260
41/260
10/343
22/343
—
9/343
37/343
Mark 76
Maximum Pressure @ 100°F, PSI/°F
Size
Packing
1/2" to 2"
2-1/2"
to 6"
Any
150#
250
Any
250
Any
TEF
GRAF
DI Body
300#
640
TE
988
150#
225
BRZ Body
300#
500
TE
500
150#
285
CS Body
300#
740
TE
1480
150#
275
SST Body
300#
720
TE
1440
640
—
—
—
—
285
740
—
275
720
—
Pressure @ Maximum Temperature, PSI/°F
170/500 495/500 808/500 150/500 325/500 325/500 170/500 600/500 1200/500 170/500 480/500 955/500
125/650 450/650 715/650 150/500 325/500 325/500 125/650 535/650 1075/650 125/650 445/650 890/650
Maximum Pressure @ 100°F, PSI/°F
Size
Packing
DN15-50
DN65-150
Any
Any
150#
17
17
Any
TEF
GRAF
12/260
9/343
DI Body
300#
44
44
TE
68
—
34/260
31/343
56/260
49/343
BRZ Body
CS Body
150#
300#
TE
150#
300#
225
16
34
20
51
—
—
—
20
51
Pressure @ Maximum Temperature, PSI/°F
10/260 22/260 22/260
12/260
41/260
10/260 22/260 22/260
9/343
37/343
-4-
TE
102
—
150#
19
19
SST Body
300#
50
50
TE
99
—
83/260
74/343
12/260
9/343
33/260
31/343
66/260
61/343
Mark 70 Sliding Gate Control Valves
Pressure-Temperature Charts – MK70, MK74, MK76
Ductile Iron
38
93
Temperature °C
260
316
371
76
600 DI/TE/DI
1000
48
300 DI
600
41
SS/Has C Bellows
34
400
28
300
21
150 DI
200
7
100
200
300
400
Temperature °F
500
260
316
83
69
1000
PTFE Pack.
800
300 DI
600
55
Std. Bolt
41
SS/Has C Bellows
28
150 DI
14
200
0
0
Carbon Steel
-18
1600
38
Temperature °C
149
204
93
Pressure (psi)
1400
260
316
1000
69
55
PTFE Pack.
Std. Bolt
41
SS/Has C Bellows
400
100
200
300
400
Temperature °F
500
0
700
600
•
Bronze
Temperature °C
10
38
65
93
121
149
Temperature °C
177
232
300/TE BR
316
41
-18
600
34
300
21
200
14
100
7
50
100
150
200
250
300
350
400
450
0
500
Pressure (psi)
28
400
38
93
149
204
300/TE BR
34
28
300
21
200
14
100
7
0
100
200
300
400
Temperature °F
-5-
316
41
400
0
Temperature °F
260
150 CI
500
Pressure (bar)
Pressure (psi)
204
150 CI
500
0
0
700
14
Cast Iron
0
600
28
0
0
-18
600
500
150 DI
200
•
400
97
83
600
300
371
110
1200
300 DI
200
Temperature °F
600/TE/SW SS
800
100
Pressure (bar)
•
371
110
97
400
0
700
600
204
500
0
600
Pressure (bar)
0
0
149
600 DI/TE/DI
14
100
93
1200
Pressure (psi)
Pressure (psi)
55
Std. Bolt
PTFE Pack.
38
1400
62
800
500
-18
1600
69
900
700
Stainless Steel
Pressure (bar)
-18
1100
•
Temperature °C
149
204
Pressure (bar)
•
Mark 70 Sliding Gate Control Valves
Dimensions
•
D
1/4" NPT
Mark 70: Threaded Ends
Size
Material
1/2" &
3/4"
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
1"
1-1/4"
B
1-1/2"
2"
•
C
•
Size
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
•
ANSI
Flange
Size
Material
A1
DN15
& 20
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DN25
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
Dimensions (inches)
A1
B
C
D
7.25
9.38
2.18
9.50
7.50
9.38
2.18
9.50
7.25
9.38
2.18
9.50
7.62
9.38
2.18
9.50
7.25
9.62
2.62
9.50
7.75
9.62
2.62
9.50
7.87
9.87
2.62
9.50
8.37
9.87
2.62
9.50
8.75
9.87
2.75
9.50
9.25
9.87
2.75
9.50
10.00 10.00 3.00
9.50
10.50 10.00 3.00
9.50
DN32
Weight
(lbs)
DN40
26
28
26
28
30
32
28
30
30
32
34
36
DN50
•
Size
DN15
DN20
DN25
DN32
DN40
DN50
ANSI PN
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
A1
130
130
150
150
160
160
180
180
200
200
230
230
Dimensions (mm)
B
C
238
55
238
55
238
55
238
55
244
67
244
67
251
67
251
67
251
70
251
70
254
76
254
76
2-1/2"
3"
4"
D
241
241
241
241
241
241
241
241
241
241
241
241
6"
Weight
(kgs)
•
11,8
12,7
11,8
12,7
12,7
13,6
12,7
13,6
13,6
14,5
14,8
16,3
A
92
93
105
105
105
114
118
114
140
Dimensions (mm)
B
C
238
55
238
55
244
67
244
67
251
67
251
67
251
70
254
67
254
76
D
241
241
241
241
241
241
241
241
241
Weight
(kgs)
10,9
10,9
11,8
12,7
11,8
12,2
12,7
13,2
14,5
ANSI
Flange
125/150#
250/300#
125/150#
250/300#
125/150#
250/300#
125/150#
250/300#
Dimensions (inches)
A1
B
C
D
10.87
16.50 5.12
9.50
11.50
11.75
16.50 5.37
9.50
12.50
13.87
17.75 6.00
9.50
14.50
17.75
18.50 7.00
9.50
18.62
Weight
(lbs)
180
195
305
380
Mark 76: Flanged Ends, DIN
Size
DN65
DN80
DN100
DN150
-6-
24
24
26
28
26
27
28
29
32
Mark 76: Flanged Ends
Size
Mark 70: Flanged Ends, DIN
Weight
(lbs)
Mark 70: Threaded Ends, DIN
A
Mark 70: Flanged Ends
Dimensions (inches)
A
B
C
D
3.62
9.38
2.18
9.50
3.65
9.38
2.18
9.50
4.12
9.62
2.62
9.50
4.12
9.62
2.62
9.50
4.12
9.87
2.62
9.50
4.50
9.87
2.62
9.50
4.65
9.87
2.75
9.50
4.50 10.00 2.62
9.50
5.50 10.00 3.00
9.50
ANSI PN
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
A1
276
290
298
310
350
368
451
480
Dimensions (mm)
B
C
D
Weight
(kgs)
419
130
241
82
419
136
241
88
451
152
241
138
470
178
241
172
Mark 70 Sliding Gate Control Valves
Dimensions
•
D
1/4" NPT
Mark 707: Threaded Ends
Size
1/2"
3/4"
B
1"
1-1/4"
1-1/2"
2"
C
•
A
A1
•
Size
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
Material
DN15
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
Dimensions (inches)
A
B
C
D
3.62
5.25
2.18
5.00
3.65
5.25
2.18
5.00
3.62
5.25
2.18
5.00
3.65
5.25
2.18
5.00
4.12
5.50
2.62
5.00
4.12
5.50
2.62
5.00
4.12
5.50
2.62
5.00
4.50
5.75
2.62
5.00
4.65
6.00
2.75
5.00
4.50
5.87
2.62
5.00
5.50
6.12
3.00
5.00
Weight
(lbs)
DN20
10
10
10
10
12
13
12
13
14
15
18
DN25
DN32
DN40
DN50
•
Size
3"
Mark 76: Threaded Ends, DIN
Size
DN15
DN20
DN25
DN32
DN40
DN50
Material
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
A
92
93
92
93
105
105
105
114
118
114
140
Dimensions (mm)
B
C
133
55
133
55
133
55
133
55
140
67
140
67
140
67
146
67
152
70
149
67
155
76
D
127
127
127
127
127
127
127
127
127
127
127
Weight
(kgs)
4"
5,4
5,4
5,4
5,4
6,4
6,8
6,4
6,8
7,3
7,7
9,1tt
6"
•
24
24
37
39
37
39
37
40
43
40
43
Material
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
A
92
93
105
105
105
105
105
114
140
114
140
Dimensions (mm)
B
C
238
55
238
55
205
67
275
67
205
67
275
67
281
67
281
67
284
76
284
67
284
76
D
241
241
318
318
318
318
318
318
318
318
318
Weight
(kgs)
11
11
17
18
17
18
17
18
20
18
20
ANSI
Flange
125/150#
250/300#
125/150#
250/300#
125/150#
250/300#
125/150#
250/300#
Dimensions (inches)
A1
B
C
D
10.87
19.50 5.12 15.00
11.50
11.75
19.50 5.37 15.00
12.50
13.87
20.75 6.00 15.00
14.50
17.75
21.50 7.00 15.00
18.62
Weight
(lbs)
210
255
325
410
Mark 707 & Mark 711: Flanged Ends, DIN
Size
DN65
DN80
DN100
DN150
-7-
Weight
(lbs)
Mark 707 & Mark 711: Flanged Ends
2-1/2"
•
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
Dimensions (inches)
A
B
C
D
3.62
9.38
2.18
9.50
3.65
9.38
2.18
9.50
4.12 10.82 2.62 12.50
4.12 10.82 2.62 12.50
4.12 10.82 2.62 12.50
4.12 10.82 2.62 12.50
4.12 11.07 2.62 12.50
4.50 11.07 2.62 12.50
4.65 11.20 3.00 12.50
4.50 11.20 2.62 12.50
5.50 11.20 3.00 12.50
Mark 707: Threaded Ends, DIN
Size
Mark 76: Threaded Ends
Material
ANSI PN
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
A1
276
290
298
310
350
368
451
480
Dimensions (mm)
B
C
D
Weight
(kgs)
495
130
381
95
495
136
381
102
527
152
381
152
546
178
381
186
Mark 70 Sliding Gate Control Valves
Ordering Schematic
Model No Size
70
70SP
70TP
707
707SP
707TP
711
711SP
711TP
050
075
100
125
400
Body Mat'l
1
2
3
4
5
6
Model
Standard
Standard with Side Positioner
Standard with Top Positioner
Equal Percentage
Equal Percentage with Side Positioner
Equal Percentage with Top Positioner
Linear
Linear with Side Positioner
Linear with Top Positioner
1/2" (DN15)
3/4" (DN20)
1" (DN25)
1-1/4" (DN32)
4" (DN100)
Size
150
200
250
300
600
DI
BR
CS
S6
1&2
PT
BT
I5
F5
I7
F7
I6
F6
BP
SW
I3
F3
I8
F8
I4
F4
End Connections
NPT
BSPT
150# IFE DI above 2" or CS or SST valves
150# FE DI below 2-1/2" or BR
PN10 IFE DI above 2" or CS or SST valves
PN10 FE DI below 2-1/2" or BR
PN16 IFE DI above 2" or CS or SST valves
PN16 FE DI below 2-1/2" or BR
BSPP
FSW
300# IFE DI above 2" or CS or SST valves
300# FE DI below 2-1/2" or BR
PN25 IFE DI above 2" or CS or SST valves
PN25 FE DI below 2-1/2" or BR
PN40 IFE DI above 2" or CS or SST valves
PN40 FE DI below 2-1/2" or BR
3&4
T3
T6
I3
I6
Trim
303SS/TFE Pkg
316SS/TFE Pkg
303SS/Graphite
316SS/Graphite
8
5
V
W
6
1
2
3
4
5
6
7
8
9
1-1/2" (DN40)
2" (DN50)
2-1/2" (DN65)
3" (DN80)
6" (DN150)
Body Material
Ductile Iron
Bronze
Carbon Steel (WCB)
Stainless Steel (CF8M)
7
10
11
12
13
14
15
Seat Material
303SS/Jorcote
316SS/Jorcote
Cv (Kv)
MK70 & MK711
0.21 (0,28)
A
25 (22)
0.42 (0,36)
B
30 (26)
0.84 (0,72)
C
50 (43)
1.6 (1,4)
F
85 (73)
2.5 (2,2)
G
115 (99)
4.4 (3,8)
H 130 (112)
6.4 (5,5)
I
200 (172)
9.5 (8,2)
J 395 (341)
15 (13,0)
7,8,9,10,11,12
N3Q3N3
Q3Q3N3
5
6
N
P
S
U
1
2
H
3
MK707
2.5 (2,2)
4.4 (3,8)
11.5 (9,9)
13 (11,2)
22 (19)
34 (29)
60 (52)
80 (69)
130 (112)
230 (199)
Mark 70 Series Range & Actuator
Range
Actuator
3-15 DIR
35M
3-15 REV
A3B3A3
B3B3A3
G3B3A3
H3B3A3
A5B5A5
B5B5A5
G5B5A5
H5B5A5
A8B8A8
B8B8A8
G8B8A8
H8B8A8
All Mark 70 Models Range & Actuator
Range
Actuator
3-15 DIR
3-15 REV
35M
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
55M
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
85M
6-30 DIR
6-30 REV
13 & 14
00
AR
H3
H5
H8
S6
Accessories
None
Air Regulator
Handwheel 35M Actuator
Handwheel 55M Actuator
Handwheel 85M Actuator
316SS Bolting
15
D
R
Action
Air-to-Close
AIr-to-Open
7,8,9,10,11,12
-8-
9
3L/T-2R/S33 Series
Mark 701/702 Series
High-Flow and Super High-Flow Control Valves
The Mark 701/702 high-flow and super high-flow sliding gate control valves provide:
Shorter Stroke than a globe or plug-style valve
• Faster response
• Longer packing and seat life
• Stem packing is four times deeper than stem
travel – for greater protection against leakage
• Smaller and lighter weight than globe-style
valves
Straight through flow
• Less turbulence, erosion and noise
• Improved rangeability
Ease of maintenance
• Interchangeable seats and Cv's
• Fewer spare parts
• Self-cleaning seats
• No gaskets or o-rings
Stem Packing: Spring-loaded Teflon (to
450°F/232°C); Graphite (to 1200°F/649°C)
Service: steam, water, oil, gas, air and chemicals
Shutoff: ANSI Class IV
Ranges: 3-15, 3-9, 9-15, 6-30 psi (0,21-1,03;
0,21-0,62; 0,62-1,03; 0,41-2,1 bar)
Action
• Direct (air signal closes valve)
• Reverse (air signal opens valve)
Positioner: Side or top mounted positioners are available to ensure that the valve stem position is always
directly proportional to the control system output
signal. See the Positioner section for more details.
Body Rating
• Ductile Iron up to 988 psi (68,1 bar) @ 100°F
(38°C) and 715 psi (49,3 bar) @ 650°F (343°C)
• Carbon Steel and Stainless Steel up to 1440
psi (99 bar) @ 100°F (38°C) and 890 psi (61
bar) @ 650°F (343°C)
• Bronze up to 500 psi (35 bar) @ 100°F (38°C)
and 325 psi (22 bar) @ 500°F (260°C)
• Temperature limit of -20°F (-29°C) on all materials; for other temperatures, consult factory
Specifications
Sizes: 1/2" through 2" (DN15 through DN50)
End Connections
• Threaded (NPT, BSPT, BSPP)
• ANSI Flanges (150#, 300#)
• DIN Flanges (PN10/16, PN25/40)
Body Materials
• Ductile Iron
• Bronze
• Carbon Steel (WCB)
• Stainless Steel (CF8M)
Trim Materials
• 303SS for CI, DI, BRZ & CS body valves
• 316SS for SS body valves
Seat Materials
• Jorcote on SST – standard
Yoke: Cast Iron
Actuator: Steel
Diaphragm: Buna-N (standard, to 200°/93°C)
-9-
Mark 701/702 High Flow & Super High Flow Sliding Gate Control Valves
Cv Values and Maximum Allowable Differential
Pressure Ratings
Dimensions
Cv
(Kv)
Seat
Material
SST
6.4
1/2" & 3/4"
Jorcote
(5,5) (DN15 & 20)
7.0
SST
1/2" (DN15)
Jorcote
(6,0)
9.5
SST
3/4" (DN20)
Jorcote
(8,2)
15
1" & 1-1/4"
SST
Jorcote
(12,9) (DN25 & 32)
18
SST
1" (DN25)
Jorcote
(15,5)
25
SST
1-1/4" (DN32)
Jorcote
(22)
30
1-1/2" & 2"
SST
Jorcote
(26) (DN40 & 50)
SST
45
1-1/2" (DN40)
Jorcote
(39)
SST
50
2" (DN50)
Jorcote
(43)
SST
65
1-1/2" (DN40)
Jorcote
(56)
70
SST
2" (DN50)
Jorcote
(61)
* 55M Actuator is optional
D
1/4" NPT
B
C
A
A1
•
Mark 701/702: Flanged Ends
Size
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
•
ANSI
Flange
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
•
Dimensions (inches)
A1
B
C
D
7.25 10.38 2.18
12.5
7.50 10.38 2.18
12.5
7.25 10.38 2.18
12.5
7.62 10.38 2.18
12.5
7.25 10.62 2.62
12.5
7.75 10.62 2.62
12.5
7.87 10.87 2.62
12.5
8.37 10.87 2.62
12.5
8.75 10.87 2.75
12.5
9.25 10.87 2.75
12.5
10.00 11.00 3.00
12.5
10.50 11.00 3.00
12.5
Weight
(lbs)
37
39
41
45
41
45
41
45
46
55
50
57
1/2"
3/4"
1"
1-1/2"
2"
•
DN15
DN20
DN25
DN32
DN40
DN50
ANSI PN
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
A1
130
130
150
150
160
160
180
180
200
200
230
230
Dimensions (mm)
B
C
263
55
263
55
263
55
263
55
270
67
270
67
276
67
276
67
276
70
276
70
284
76
284
76
D
318
318
318
318
318
318
318
318
318
318
318
318
Weight
(kgs)
16,8
17,7
18,6
20,4
18,6
20,4
18,6
20,4
20,9
24,9
22,7
25,9
35M w/Positioner
125 (8,6)
200 (13,8)
125 (8,6)
200 (13,8)
125 (8,6)
200 (13,8)
100 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
150 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
100 (6,9)
150 (10,3)
150 (10,3)
250 (17,2)
150 (10,3)
250 (17,3)
150 (10,3)
250 (17,2)
100 (6,9)
200 (13,8)
100 (6,9)
200 (13,8)
100 (6,9)
200 (13,8)
100 (6,9)
200 (13,8)
100 (6,9)
200 (13,8)
100 (6,9)
200 (13,8)
125 (8,6)
150 (10,3)
125 (8,6)
150 (10,3)
Material
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
Dimensions (inches)
A
B
C
D
3.62 10.38 2.18 12.50
3.65 10.38 2.18 12.50
3.62 10.38 2.18 12.50
3.65 10.38 2.18 12.50
4.12 10.62 2.62 12.50
4.12 10.62 2.62 12.50
4.50 10.87 2.62 12.50
5.00 10.87 3.00 12.50
4.50 11.00 2.62 12.50
5.50 11.00 3.00 12.50
Weight
(lbs)
35
35
35
35
37
39
40
43
40
43
Mark 701/702: Threaded Ends, DIN
Size
DN15
DN20
DN25
DN40
DN50
-10-
55M Actuator*
Mark 701/702: Threaded Ends
Size
Mark 701/702: Flanged Ends, DIN
Size
Max ∆P, PSI (BAR)
Valve Size
(DN)
Material
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
CS/SS
A
92
93
92
93
105
105
114
140
114
140
Dimensions (mm)
B
C
264
55
264
55
264
55
264
55
270
67
270
67
284
67
284
76
284
67
284
76
D
318
318
318
318
318
318
318
318
318
318
Weight
(kgs)
16
16
16
16
17
18
18
20
18
20
Mark 701/702 High Flow & Super High Flow Sliding Gate Control Valves
Pressure-Temperature Charts – MK701/702
Ductile Iron
93
Pressure (psi)
Temperature °C
260
316
600 DI/TE/DI
1000
371
76
62
800
55
500
Std. Bolt
PTFE Pack.
300 DI
600
34
400
28
200
300
400
Temperature °F
500
600
149
204
260
316
371
110
97
83
600 DI/TE/DI
7
100
93
1200
14
100
38
1400
21
150 DI
200
0
0
48
41
SS/Has C Bellows
300
-18
1600
69
900
700
Stainless Steel
69
1000
PTFE Pack.
800
300 DI
600
55
Std. Bolt
41
SS/Has C Bellows
28
400
0
700
Pressure (bar)
38
Pressure (psi)
-18
1100
•
Temperature °C
149
204
Pressure (bar)
•
150 DI
14
200
0
0
100
200
300
400
500
600
0
700
Temperature °F
Carbon Steel
93
Pressure (psi)
1400
260
316
1200
83
1000
69
55
600
300 DI
PTFE Pack.
Std. Bolt
41
SS/Has C Bellows
400
-18
600
150 DI
14
100
200
300
400
Temperature °F
38
93
149
204
260
500
600
150 CI
500
28
200
0
0
Temperature °C
371
110
97
600/TE/SW SS
800
Bronze
0
700
34
400
28
300
21
200
14
100
7
0
-11-
300/TE BR
316
41
0
100
200
300
400
Temperature °F
500
0
600
Pressure (bar)
38
Pressure (psi)
-18
1600
•
Temperature °C
149
204
Pressure (bar)
•
Mark 701/702 High Flow & Super High Flow Sliding Gate Control Valves
Ordering Schematic
Model No Size
Body Mat'l
1
2
3
4
5
701
701TP
702
702TP
Model
High Flow
High Flow with Top Positioner
Super High Flow
Super High FLow with Top Positioner
050
075
100
125
150
200
Size
1/2" (DN15)
3/4" (DN20)
1" (DN25)
1-1/4" (DN32)
1-1/2" (DN40)
2" (DN50)
DI
BR
CS
S6
Body Material
Ductile Iron
Bronze
Carbon Steel (WCB)
Stainless Steel (CF8M)
1&2
PT
BT
I5
F5
I7
F7
I6
F6
BP
SW
I3
F3
I8
F8
I4
F4
End Connections
NPT
BSPT
150# IFE DI above 2" or CS or SST valves
150# FE DI below 2-1/2" or BR
PN10 IFE DI above 2" or CS or SST valves
PN10 FE DI below 2-1/2" or BR
PN16 IFE DI above 2" or CS or SST valves
PN16 FE DI below 2-1/2" or BR
BSPP
FSW
300# IFE DI above 2" or CS or SST valves
300# FE DI below 2-1/2" or BR
PN25 IFE DI above 2" or CS or SST valves
PN25 FE DI below 2-1/2" or BR
PN40 IFE DI above 2" or CS or SST valves
PN40 FE DI below 2-1/2" or BR
3&4
T3
T6
Trim
303SS/TFE Pkg
316SS/TFE Pkg
5
A
B
V
W
Seat Material
303SST
316SST
303SS/Jorcote
316SS/Jorcote
6
7
8
6
7
L
M
8
9
R
T
7,8,9,10,11,12
A3B3A3
B3B3A3
G3B3A3
H3B3A3
A5B5A5
B5B5A5
G5B5A5
H5B5A5
A8B8A8
B8B8A8
G8B8A8
H8B8A8
-12-
9
10
11
6.4 (5,5)
6.4 (5,5)
9.0 (7,8)
9.5 (8,2)
15 (13)
18 (15,5)
24 (21)
12
13
14
Cv (Kv)
A
B
V
W
C
Y
E
15 16
25 (22)
30 (26)
35 (31)
45 (39)
50 (43)
65 (56)
70 (60)
Range & Actuator
Range
Actuator
3-15 DIR
3-15 REV
35M
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
55M
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
85M
6-30 DIR
6-30 REV
13 & 14
00
AR
H3
H5
H8
S6
Accessories
None
Air Regulator
Handwheel 35M Actuator
Handwheel 55M Actuator
Handwheel 85M Actuator
316SS Bolting
15
D
R
Action
Air-to-Close
AIr-to-Open
16
0
3
5
8
I/P
None
I/P 35M Actuator
I/P 55M Actuator
I/P 85M Actuator
3L/T-2R/S33 Series
Mark 74 Series
Bellows Seal Control Valve
When dealing with clean air requirements, you need to
feel confident that you will receive long-term, leak-free
performance from your bellows stem seal valves. You
will find this assurance with the Mark 74 from Jordan
Valve. The Mark 74 provides exceptional bellows life
with a valve stroke that is just a fraction of that of other
rising stem valves. This means Jordan Valve can use
a smaller formed bellows that has minimal movement
during operation. With limited movement, the bellows
is not subjected to excessive wear and fatigue – conditions that can quickly lead to failure in other designs. In
actual laboratory evaluations the valves tested exceeded two million throttling cycles in Class 300 service
with no failures of the SST bellows. You can expect
the Mark 74 to provide long-term, dependable service
to meet Clean Air requirements.
For compliance with the most stringent requirements of the Clean Air Act, the Mark 74 controls
fugitive emissions while reducing the risks associated with toxic, corrosive, explosive and high
temperature fluids.
Features
Specifications
•
Long bellows life – in actual lab tests, the Mark
74 exceeded 2 million cycles with no bellows
failures
•
Short stroke – with a valve stroke that's just a
fraction of that of other rising stem valves, the
Mark 74 uses a smaller bellows that has minimal
movement during operation. With limited movement, the bellows is not subjected to excessive
wear and fatigue, conditions that can quickly lead
to failure in other valve designs.
•
Fully packed back-up seal – for additional assurance, a secondary chamber of multiple packing
rings provides extra leakage protections
•
Detection/monitoring port – a gauge can be
mounted to verify bellows performance
•
Totally enclosed multi-spring actuator – minimizes deadband and is field reversible without the
use of special tools or additional parts
•
Specialty alloys available – ideal for toxic or corrosive services
-13-
Sizes: 1/2" through 2" (DN15 through DN50)
End Connections
• Threaded (NPT, BSPT, BSPP)
• ANSI Flanges (150#, 300#)
• DIN Flanges (PN10/16, PN25/40)
Body Materials
• Ductile Iron
• Bronze
• Carbon Steel (WCB)
• Stainless Steel (CF8M)
Trim Materials
• 303SS – standard for Ductile Iron, Bronze or
Carbon Steel valves
• 316SS – standard on Stainless Steel valves
Seat Materials
• Jorcote on SST – standard
Bellows
• 316SS
• Hastelloy C
Mark 74 Bellows Stem Seal Control Valve
Specifications
Yoke: Cast Iron
Actuator: Steel
Auxilliary Stem Packing
• Spring-loaded Teflon® (to 500°F/260°C)
• Braided (above 500°F/260°C)
Auxilliary Stem Packing
• Spring-loaded Teflon® (to 500°F/260°C)
• Braided (above 500°F/260°C)
Body Rating: Ductile Iron, Carbon Steel, and
Stainless Steel up to 500 psi (34,5 bar) and 650°F
(343°c); bronze up to 500 psi (34,5 bar) depending upon specific construction. Temperature limit
of -20°F (-28,9°C) on all materials.
Action
• Direct (air-to-close)
• Reverse (air-to-open)
Shutoff: ANSI Class IV
Ranges: controller-operated: 3-15, 3-9, 6-30, 9-15
psi (0,2-1,0; 0,2-0,6; 0,4-2,1; 0,6-1,0 bar)
Positioners: side or top mounted positioners are
avilable (specify Mark 74P)
Rangeability
• Mark 74 (1/2" – 1-1/2") (DN15 – DN40): 100:1
• Mark 74 2" (DN50): >200:1
Max ∆P, PSI * (BAR)
Cv
(Kv)
Valve Size
(DN)
Seat
Material
Mark 74
Mark 74P
2.5 (2,2)
4.4 (3,8)
1/2" to 3/4"
DN8 to 20
SST
125 (8,6)
175 (12,1)
Jorcote
250 (17,2)
500 (34,5)
6.4 (5,5)
9.5 (8,2)
1" & 1-1/4"
DN25 & 32
SST
100 (6,9)
150 (10,3)
Jorcote
150 (10,3)
300 (20,7)
15 (12,9)
1-1/2"
DN40
SST
25/30
(22/26)
2"
DN50
Jorcote
75 (5,2)
125 (8,6)
125 (8,6)
250 (17,2)
Mark 741
Mark 741P
SST
100 (6,9)
125 (8,6)
Jorcote
150 (10,3)
175 (12,1)
100 (6,9)
125 (8,6)
150 (10,3)
175 (12,1)
Mark 742
Mark 742P
High Flow
30 (26)
1-1/2" & 2"
Dn40 & 50
45 (39)
1-1/2"
DN40
50 (43)
2"
DN50
SST
Jorcote
Super High Flow
65 (56)
1-1/2"
DN40
SST
Jorcote
100 (6,9)
125 (8,6)
70 (60)
2"
DN50
SST
Jorcote
150 (10,3)
150 (10,3)
-14-
Mark 74 Bellows Stem Seal Control Valve
Dimensions
D
1/4" NPT
B
1/4" NPT
C
A
A1
•
Mark 74: Flanged Ends
Size
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
•
ANSI
Flange
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
•
Dimensions (inches)
A1
B
C
D
7.25 12.38 2.18
9.50
7.50 12.38 2.18
9.50
7.25 12.38 2.18
9.50
7.62 12.38 2.18
9.50
7.25 12.62 2.62
9.50
7.75 12.62 2.62
9.50
7.87 12.87 2.62
9.50
8.37 12.87 2.62
9.50
8.75 12.87 2.75
9.50
9.25 12.87 2.75
9.50
10.00 13.00 3.00
9.50
10.50 13.00 3.00
9.50
Weight
(lbs)
29
31
31
33
33
36
33
37
36
43
42
49
DN15
DN20
DN25
DN32
DN40
DN50
ANSI PN
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
10/16
25/40
A1
130
130
150
150
160
160
180
180
200
200
230
230
Dimensions (mm)
B
C
314
55
314
55
314
55
314
55
321
67
321
67
327
67
327
67
327
70
327
70
330
76
330
76
D
241
241
241
241
241
241
241
241
241
241
241
241
Material
1/2" &
3/4"
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
1-1/4"
1-1/2"
2"
•
Weight
(kgs)
11,8
12,7
11,8
12,7
12,7
13,6
12,7
13,6
13,6
14,5
14,8
16,3
Size
1"
Mark 74: Flanged Ends, DIN
Size
Mark 74: Threaded Ends
Dimensions (inches)
A
B
C
D
3.62 12.38 2.18
9.50
3.65 12.38 2.18
9.50
4.12 12.62 2.62
9.50
4.12 12.62 2.62
9.50
4.12 12.87 2.62
9.50
4.50 12.87 2.62
9.50
4.65 12.87 2.75
9.50
4.50 13.00 2.62
9.50
5.50 13.00 3.00
9.50
Weight
(lbs)
27
27
29
30
29
30
31
32
35
Mark 74: Threaded Ends, DIN
Size
Material
DN15
& 20
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DI/BRZ
DI/BRZ
CS/SS
DI/BRZ
CS/SS
DN25
DN32
DN40
DN50
A
92
93
105
105
105
114
118
114
140
Dimensions (mm)
B
C
314
55
314
55
321
67
321
67
327
67
327
67
327
70
330
67
330
76
D
241
241
241
241
241
241
241
241
241
Weight
(kgs)
12,2
12,2
12,6
13,6
12,6
13,6
14,1
14,5
15,9
"B" Dimensions are for 35M actuator, for 55M actuator add
1.2" (30,5mm), for 85M actuator add 2" (50,8mm)
"D" Dimensions are for 35M actuator, for 55M actuator add 3"
(76,2mm), for 85M actuator add 5.5" (140mm)
-15-
MK70/0614/AB
Mark 74 Bellows Stem Seal Control Valve
Ordering Schematic
Model No Size
Body Mat'l
1
2
3
4
5
74
74TP
74SP
Model
Bellows Seal
Bellows Seal with Top Positioner
Bellows Seal with Side Positioner
050
075
100
125
150
200
Size
1/2" (DN15)
3/4" (DN20)
1" (DN25)
1-1/4" (DN32)
1-1/2" (DN40)
2" (DN50)
DI
BR
CS
S6
Body Material
Ductile Iron
Bronze
Carbon Steel (WCB)
Stainless Steel (CF8M)
1&2
PT
BT
I5
F5
I7
I6
BP
SW
I3
F3
I8
I4
End Connections
NPT
BSPT
150# IFE DI above 2" or CS or SST valves
150# FE DI below 2-1/2" or BR
PN10 IFE DI above 2" or CS or SST valves
PN16 IFE DI above 2" or CS or SST valves
BSPP
FSW
300# IFE DI above 2" or CS or SST valves
300# FE DI below 2-1/2" or BR
PN25 IFE DI above 2" or CS or SST valves
PN40 IFE DI above 2" or CS or SST valves
3&4
B3
B6
BH
Trim
303SS/TFE Pkg/316 Bellows
316SS/TFE Pkg/316 Bellows
H-C/TFE Pkg/H-C Bellows
5
V
W
Seat Material
303SS/Jorcote
316SS/Jorcote
6
7
6
1
2
3
4
5
6
7,8,9,10,11,12
N3Q3N3
Q3Q3N3
C3B3A3
D3B3A3
E3B3A3
F3B3A3
G3B3A3
H3B3A3
A5B5A5
B5B5A5
C5B5A5
D5B5A5
E5B5A5
F5B5A5
G5B5A5
H5B5A5
A8B8A8
B8B8A8
C8B8A8
D8B8A8
E8B8A8
F8B8A8
G8B8A8
H8B8A8
8
9
10
0.21 (0,28)
0.42 (0,36)
0.84 (0,72)
1.6 (1,4)
2.5 (2,2)
4.4 (3,8)
11
12
13
Cv (Kv)
7
8
9
A
B
14
15
6.4 (5.5)
9.5 (8,2)
15 (13)
25 (22)
30 (26)
Range & Actuator
Range
Actuator
3-15 DIR
3-15 REV
3-9 DIR
3-9 REV
35M
9-15 DIR
9-15 REV
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
3-9 DIR
3-9 REV
55M
9-15 DIR
9-15 REV
6-30 DIR
6-30 REV
3-15 DIR
3-15 REV
3-9 DIR
3-9 REV
85M
9-15 DIR
9-15 REV
6-30 DIR
6-30 REV
13 & 14
00
AR
S6
Accessories
None
Air Regulator
316SS Bolting
15
D
R
Action
Air-to-close
Air-to-open
16
0
3
5
8
I/P
None
I/P 35M Actuator
I/P 55M Actuator
I/P 85M Actuator
Jordan Valve, a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Jordan Valve reserves the right to make revisions to its product, specifications, literature and related information without notice. Please visit our
website at www.jordanvalve.com for the latest information on our products.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement