RDS | A100 | Service manual | RDS A100 Service manual

Ultimail
diagnostic code
diagnostic message
remedy
Warning!
Information contained in this document is propritary and the sole property of
Francotyp-Postalia.
This information is confidental and for internal use only. Any disclosure, transmittal or
reproduction to a second party will be procecuted. Francotyp-Postalia reserves the right to
take action, to the fullest extend allowed by law, against both the party discloses
Francotyp-Postalia's proprietary information and the party that recieves it.
Ultimail
ISS international service support
email: iss@francotyp.com
created : 20.11.2007 19:33
diagnostic code
diagnostic message
remedy
pictogram legend:
The following notes only provides information. In most no
error has occured
Customer and Hotline may be able to solve the problem without a
technica visit.
Technican repair or service required. Check whether on-site visit
or use of bing-in service is required for the procuct in question.
To continue assessment Hotline or Second-Level-Support require
transmission of remote-diagnostics-data
Note about the transmission of remote-diagnostic-data:
Whenever possible, the customer always should transmit machine remote-diagnostics-data a technican visit occurs
Wherever the Remote-diagnostics symbol appears in the following pages, transmission of the data is required for
further analysis of the error message.
Ultimail
ISS Internationaler Service Support
email: iss@francotyp.com
created : 20.11.2007 19:33
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
A001
FM is not in READY mode
C: Insert Master card
A002
no modem detected
T: Run modem test in SERVICE MODE
A100
A100 followed by C303 memory error
NV-Ram
memory error NV-ram . This can occur if software release 05.00.00 to 05.01.15 was used in Ultimail.
Diagnosis list:
31.07.07 12:59:04 C303 00000005 FFFFFFFF Serialtask could not started
31.07.07 12:59:03 A100 00007FDE 00007FFE A100 Process cannot be started!
remedy:
Mainboard has to be changed. No customer specific backup (by SSM-PC) is allowed, because
corrupeted Memory would be copied also !
Process initialization failed. IBIP-PSD
systems can have timeout problems
during the power on
no communication between PSD and main board
=> HS-Loop is open
Enter the Service mode and reset the HS-Loop. If it is not successful, please check the security switch
on the back panel (main board), SD Interface connection and the print data cable.
C007
General error with FPI
see O007
C008
meter is unkown in the TDC
Contact TDC admin
C026
The security module is not in VALID
status and the cause is not expiry of the
PieceCredit or DateCredit. The most likely
cause is that the HS LOOP is open or has
been opened.
To clear the error: Close HS LOOP and then perform PVD.
Complete the authorization during your installation process
A100
C007
Ultimail
0000 0004
0000 000A
=> H: restart the system can solve the problem. A SW update (min. 02.31.00 is required)
=>T: disconnect/connect the PSD again at the main board interface, check/exchange the adapter
board or main board
ISS international service support
email: iss@francotyp.com
page 3
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C100
Process initialization failed.
root causes will be highlighted at subsequent diagnosis codes
C101
Insufficient credit loaded to security
module.
No money loaded / Security Module not plugged
=> C: download postage
=> T: plug SM
C102
No credit in this account.
=> C: assign credit to appropriate account
C103
0000 0000
xxxx xxxx
Invalid SD status.
state is UNDDEFINED
SD is not right connected/defect
if the step from autorized to valid is not running-> expand the piece credit
the registration by the postal authority is required
=> T: connect the SD, check the state
exchange the SD Adapter board
C103
0000 0001
xxxx xxxx
invalid SD state
State is MANUFACTURED
SD is connected but invalid state
exchange the SD
the registration by the postal authority is required
C103
0000 0002
xxxx xxxx
invalid SD state
State is NEW
There is the very first initializing (OMI1) in the factory missing
send the machine back to FP
C103
0000 0003
xxxx xxxx
invalid SD state
state is INITIALIZED
Not a Error!
Installation must be completed
C103
0000 0004
xxxx xxxx
invalid SD state
state is AUTHORIZED
C: Run Teleset
C: Send the remote data, check the date- and pieces credit and the HS-Loop state
If the date/pieces credit is low and get not refreshed by a reset, please contact TDC/FPI Admin.
If the HS-Loop is open then a technican is required
C103
Ultimail
0000 0005
xxxx xxxx
SD state is VALID
can normally not be happen, because the machine is valid
ISS international service support
email: iss@francotyp.com
page 4
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C103
0000 0006
xxxx xxxx
SD state is not invalid
SD state is WITHDRAWN
Customer may have withdrawn the meter by itself?
C103
0000 0007
xxxx xxxx
invalid SD state
state is SCRAPPED
SD is finaly scrapped
C103
0000 0008
xxxx xxxx
invalid SD state
state is DEFECT
SD is not right connected
Exchange the SD, but a new postal registration is required
C103
0000 0009
xxxx xxxx
invalid SD state
state is CRYPTO_MODULE
SD is not right connected
Exchange the SD, but a new postal registration is required
Cannot print.
=> Probably sequence error, switch machine off and on again, if necessary unplug main plug
printing impossible ; State: starting
Please have a close look to the other diagnosis codes. It might be a subsequent fault.
C104
C104
0000 0000
xxxx xxxx
=> T: run re-initializing by using a FP-card (workshop only!)
Remedy:
1.) unplug machine and power on again.
Please contact your hotline and create a support request
C104
0000 0004
xxxx xxxx
machine is not ready
meter is in the initializing process
Try again after the init, autorization and teleset is completed
C104
xxxx xxxx
0000 0001
machine is not ready
SD is not correct connected
please install the Sd correct
exchange the SD adapterboard
C104
xxxx xxxx
0000 0004
printing impossible
State: ErrRunMeterInitialize => meter
initializing failed
Please contact your hotline and create a support request
Ultimail
ISS international service support
email: iss@francotyp.com
page 5
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C104
xxxx xxxx
0000 0005
machine is not ready
the autorization failed
repeat autorization
C104
xxxx xxxx
0000 0006
machine is not ready
the accounting process failed
start meter again and try again.
C104
xxxx xxxx
0000 0007
printing impossible
State: ErrNoMoneyInSD => No money
availeble in the SD
run teleset, load money
C104
xxxx xxxx
0000 0008
machine is not ready
no money for this account
change cost account
run teleset
Cannot perform franking.
Inkjet cartridges not inserted / cartridges not correct calibrated / RDS not in correct position
if subcode 1=000000B, than incorrect cliche data are possible => C: insert inkjet catridges / C: check
that green catches lock both cartridges correct / C: calibrate cartridges (remove cartridges and insert
them again)
Metering and weighing impossible => may
missing/incorrect print image data
Install new print image data
C105
C105
0000 000B
xxxx xxxx
=>C: Check Mem 1 settings, Mem 1 is the power up reference, please program correct settings which
make sence.
=>C: Check if there is a rate table present. Send remote diagostic data.
If there is SW <03.11.00 in use error C105 appears (also PCE countrys). Since 03.11.00 you get error
M145 if a rate table is missing.
=>C: Run a cartridge calibration again by simulate a cartridge exchange (use the old cartridges again)
C106
The machine cannot be switched off.
=> C: wait a while, unplug mains plug
C107
NVRAM RECALL performed
This diagnosis code is not used.
Ultimail
ISS international service support
email: iss@francotyp.com
page 6
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C108
No communication with security module
Security Module not plugged / defective
should be done by technicain:
1) run SD echo test and SD selftest in Service mode
check/plug/connect SM correctly again
Since Jan/04 the SD/main board connection get modificated. A bad connection is improbably.
C109
Cannot perform franking: last postage rate
loading too long ago! Please perform
TELESET. Amount 0 is sufficient.
=> C: run TELESET with '0‘
=> C: T: check system info -> pieces and date credit, maybe contact the TDC-Team to set a new credit
Subcode 2: 0000 0001 Datecredit expired,
C109
xxxx xxxx
0000 0001
Cannot perform franking: last postage rate
loading too long ago! Please perform
TELESET. Amount 0 is sufficient.
=> C: run teleset 0 is enough
=> C: T: check system info -> pieces and date credit, maybe contact the TDC-Team to set a new credit
Date credit is expired
Cannot perform franking: last postage rate
loading too long ago! Please perform
TELESET. Amount 0 is sufficient.
=> C: run teleset 0 is enough
Please perform TELESET first.
Advance warning for C109
Warning before C109
=> C: run TELESET with '0‘
C111
Service interval reached! Please contact
FP service dept.
=> C: clear error message, call customer service for maintenance
C112
The descending register (R1) is below the
set warning threshold! Please perform
TELESET in good time.
=> C: run TELESET
C113
Memory battery B is almost flat, please
replace it immediately!
=> C: replace battery, only use original FP battery
C109
C110
Ultimail
xxxx xxxx
0001 0000
ISS international service support
email: iss@francotyp.com
page 7
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C114
Battery B (extern) is too low. Franking is
impossible.
=> C: replace battery, only use original FP battery
=> T: 1) check batt contacts
2) check cable batt -> main board
3) exchange splitter board in SD housing
4) in some rare cases the SD is not or bad connected
Subcode 1 show actual batt. Voltage in
mV (<2950mV)
C115
The SD battery is almost flat, have FP
service dept.
=> E: replace Security Module
C116
Decimal mode: Faulty setting found!
amount is using 1/10 cent. This is not allowed by software.
Remedy:
1.) use amount without 1/10 cent
2.) perform software update franking machine
3.) perform software update ratetable
C117
FM was locked by Dealer, unlock is
possible by entering unlock-Code
=> Support: call international ServiceSupport
C118
Please first perform TELESET. Amount 0
will be sufficient.
Advance warning for C119, no TELESET was performed for too long time ago so no COM data could
be transferred => C: run TELESET with '0‘
C119
Metering cannot be performed: Last
TELESET was too long ago! Please
perform TELESET. A zero value
download will be sufficient.
No TELESET was performed for too long time ago so no COM data could be transferred
Metering cannot be performed: Last
TELESET was too long ago! Please
perform TELESET. A zero value
download will be sufficient.
(especially for NLD: COM data are not
Run Teleset
Zero reset
C120
Please check if the postage rate table is
still valid. Franking is only permitted with a
valid rate table.
Last PVD is longer ago as specified under RATE_TABLE_UPDATE_WARNING_INTERVAL (56 days)
=> C: run TELESET with '0'
C121
The batch commands are not in proper
order,
e.g. StartBatch was sent before
BatchData.
The proper order is documented in the
The batch commands transferred from external devices (e.g. GKBK-PC, semi-dynamic scale) via the
serial interface to the ultimail were not in the proper order. => Change software of the external devices.
C119
Ultimail
8000 0000
0000 0000
=> C: run TELESET with '0‘
ISS international service support
email: iss@francotyp.com
page 8
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C122
In the parameters of the batch commands
is an error!
e.g.
ProductCode = 0
letterId = 0
A parameter transferred in the batch commands from external devices (e.g. GKBK-PC, semi-dynamic
scale) was invalid. => Change software of the external devices.
C123
Error with external scales. Please note the
display on the scales.
remedy see display dyn. scale
Error protocol version of the scale.
The software version (protokoll) of the scale does not correspond with the ultimail.
C124
Please verify the cable between dyn. scale and franking machine.
Remedy:
Verify software releases of franking machine and external scale.
C150
Internal error: Accounting service cannot
be opened.
Security Modue not plugged / defective / sequence error H103
=>E: 1)plug SD correct check or 2) exchange adapter board in SD housing
3) exchange mainboard
Info:
Error C150 is only possible if the PSD is in the state valid.
The accounting service becomes open before the letter transport starts, to make sure everything is
ready (pieces- date credit money availeble...). C150 is a message byside of C109 and E113
Check the connection between main board, adapter board (in the PSD housing) and PSD
C151
No credit loaded to security module.
No money loaded / Security Module not plugged / defective
=>C: run TELESET
C152
No credit in this account.
=> C: run TELESET
C154
Internal error: Print image could not be
created!
Probably sequence error
No account selected: Please insert an
access card.
Eventually a contact problem
C155
Ultimail
=>C: clear error message, if necessary restart FM
=> C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure
point
ISS international service support
email: iss@francotyp.com
page 9
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
C156
Internal error: Letter started but not
completed.
=> C: insert letter again
C157
Internal error: Process steps not
recognized.
=>C: switch FM off/on again
C158
Internal error: READY_flags not present!
=> C: run TELESET with '0'
C159
Ink cartridges misaligned.
Ink cartridges are missing / are defective / not contacted, cartridges were removed and then swapped
=> C: perform a cartridge change with used cartridges, if all nothing helps insert new cartridges
C160
valid imprints are possible only, if the PC
(Karat) signal is present.
Please check the Karat state.
=> Please switch the KARAT (PC-System) into the ready mode
C161
Print system is not ready!
Please return to READY mode by using
Setup => select mode => franking => standard franking
or
press C/CE minimum 3 seconds
please check previous diagnosis codes, may be a inherited error
e.g.: Cartridge are not detected. Info out of the field: SW update >2.39.xx solve this Problem.
C305
Security task start up failed due to error.
Security Module not plugged / defective
=> E: plug Security Module again,
change adapter board (in the PSD housing),
change main board
C307
Ultimail
Keyboard task start up failed due to error.
=> T: run keyboard test, check cabel
ISS international service support
email: iss@francotyp.com
page 10
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
D007
It can be a problem in machines with old
SD SW.
make a SD SW update. The actuell version can be checked in the SAD report unter APP SW
VERSION!
This update can be done only in the workshop, because the SD must be in the state initialized
(FP-card requried!)
Don't find account
It's only a warning, please confirm with ENTER
make a software update 02.36.00 and higher
D032
0000 0019
0000 0005
see technical bulletin 11
D036
Account didn't exist => maybe chip card
contact problem
check the chip card 8direction, clean, correct one?)
D037
No access to account currently set=>
Contact problem with chip card
C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure point
D043
Meter is locked in TeleportoDataCenter
Please contact the dataCenter administrator
D109
No credit in current account.
C: assign credit to appropriate account, if necessary run TELESET
D113
Low postage warning for current account.
Credit below set warning threshold.
=> C: assign credit to appropriate account
D114
No card when attempting to set postage
value
Contact problem with chip card
Internal user interface error
=> Error in user interface
D115
=> C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure
point
C: send diagnostic data
error is fixed with SW 02.39.07 and higher
deselect optimizing the rate calculation
Ultimail
ISS international service support
email: iss@francotyp.com
page 11
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
D116
Security module communication error
Security device is not plugged in the right way or is defect.
Remedy:
Verify position of security device and perform selftest to check functionality.
E100
Unable to position (reference) print
cartridge direction.
Green catches at Inkjet cartridges are not latched / cartridge flap open
=> C: check green catches (start menu 'change ink cartridges' but abort after check), close cartridge
flap
=> T: 1) Enter service mode->motortest -> make refernce test several times. If the reference change
more than 5, please check RDS mover mechanic, is the set screw open (not tide)? (see service
manual Chap.3 page.8
2) run Sensortest may be the position sensors are defect!
E102
The control data for the pen carrier is
invalid.
Sequence error =>
E106
Incorrect command for setting the
parameters for the pen carrier.
=> T: check the RDS mover drive
check fuse on the main board
exchange mainboard
E108
Incorrect command for starting the pen
mover during sensor test.
Green catches at Inkjet cartridges are not latched / cartridge flap open
=>C: check green catches (start menu 'change ink cartridges' but abort after check), close cartridge
flap
T: 1) Connector between upper housing and lower unit is not connected?
2) Cartridge micro switch is defect/ not actuated?
3) during main board exchange is the big flat ribbon cable not connected/defect?
E109
Ultimail
Incorrect speed set for letter transport.
Feeder connected to ultimail 60 or sealer connected to ultimail 90 => SW didn't allow to use this
combination
ISS international service support
email: iss@francotyp.com
page 12
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E110
Letter in feeder letter transport.
=> C: remove letters / E: check sensors
E111
Letter in sealer letter transport.
=> C: remove letters / E: check sensors
E112
Referencing for pen carrier failed.
Green catches at Inkjet cartridges are not latched / cartridge flap open => C: check green catches
(start menu 'change ink cartridges' but abort after check), close cartridge flap
E113
Unable to complete preparation of print
data before start of printing.
Sensor error? SW error? => C: clear error message, feed unprinted letters again
E114
Print cartridge flap is open.
=> C: close cartridge flap
=> T: run sensor test, clean, change light barrier on the cartridge flap
E115
Letter transport roll box is open.
Microswitch is not triggered correct by letter transport with counter rollers beneath the Inkjet cartridges
=> C: pull out letter transport and insert it again (please refer to section removing letter jams of ultimail
operator manual)
=>T:: trigger microswitch manually on the rear right side of the insertion area for the letter transport,
press 'Start', clear error message, and check if drive starts
E116
Interval between two letters too small.
1&2: Interval LS3_Close - LS3_Open too
small, (less than 400 (34mm) encoder
pulses), (MIN_LETTER_GAP_CNT)
Separation error / print start sensor dirty / too fast feeding in sealer mode
Ultimail
=>C: feed letters with larger clearance
E: print start sensor, check separator in feeder unit
ISS international service support
email: iss@francotyp.com
page 13
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
E117
Letters jammed! Please remove letters.
remedy
Letter Jam/ sensor blocked
=> C: a) remove jam (eject roller box),
b) does the customer use oversized envelopes?
c) Also occurs when letter inserted past LS2 and then removed!
A sensor is actually covered (e.g. paper or dust), in this case subcode 1 from V02.03.00 shows:
1=light barrier covered, 0=light barrier open
Sequence from left to right: LFD LFS LS1 LS2 LS3
Also gives subcode (error info 1) e.g. XXX01100
LFD open, LFS and LS1 covered, LS2 and LS3 open.
=>T: 1) clean/test LS3 sensor. The value for this sensor LS3 in the system info must be between
70-140. ( If the value is 199 or 0 then we have mybe a defect main board)
2) Letter lenght is incorrect -> bad separtion?
a.Letter length exceeded at LS3 (MAX 381 mm)
b.Letter length exceeded at LS2 (MAX 381 mm)
3) run in service mode
a) encoder test
b) sensor test
c) check the sensor regulation offset
4) Maybe the LS1 and LS2 activation lever are not correct in position?
5) check the sensor cable
E118
Unable to switch on print voltage
please check diagnosis description on subcodes according E127
Technicain should check:
1.) contact to cartridge
2.) change cartridge
3.) may be replace PDB
4.) may be repace mainboard
E120
Unable to bring the pen carrier into
position for changing the cartridges.
=> position light sensors defect? run sensor test in Service mode
MTS mechanically blocked? run motortest in service mode
E121
Unable to bring the pen carrier into the
cleaning and sealing station (RDS).
=> position light sensors defect? run sensor test in Service mode
MTS mechanically blocked? run motortest in service mode
E122
Unable to bring the pen carrier into
printing position.
=> position light sensors defect? run sensor test in Service mode
MTS mechanically blocked? run motortest in service mode
E124
The MTS mover has determined a new
position value for the print position during
the referencing operation.
After ink cartridge change: other reference values are valid (normal deviation) / or: green catches at
Inkjet cartridges are not latched
Ultimail
=>C: clear error message, check green catches at Inkjet cartridges
=> T: service mode -> Motor test-> S6 Motor status report
ISS international service support
email: iss@francotyp.com
page 14
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E126
Unable to calibrate the sensor for control
of print starting point (LS3).
Letter jam / print start sensor dirty
=> C: remove letters from letter passage (please refer to section removing letter jams of ultimail
operator manual)
=> E: clean/test print start sensor. The value for LS3 in the system info must be between 70-140. (If
the value is 199 or 0, maybe the mainboard is defect) (regulation offset)
E127
The calibration of the cartridges failed
Contact problems /bad cartridge?
Cotact problem /Cartridge failer
Please use the subcode
=> C: exchange cartridge, install again
=> T: run contact test in Service mode
search for your subcode…
see also technical bulletin #1
E127
xx1x xxxx
xxxx xxxx
left cartridge => print voltage to high
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check temperatur on the cartridge in service mode => cartridge
info
see also technical bulletin #1
E127
xx2x xxxx
xxxx xxxx
left cartridge => low voltage
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
E127
xx4x xxxx
xxxx xxxx
left cartridge => contact problem
Cotact problem /Cartridge failer
=> C: exchange cartridge, install again
=> T: run contact test in Service mode
search for your subcode…
see also technical bulletin #1
E127
xx8x xxxx
xxxx xxxx
left cartridge => identification error
=>C: install cartridge again, exchange the cartridge
maybe wrong or non FP cartridge?
=>T: run contact test in service mode and clean the contacts
E127
xxx1 xxxx
xxxx xxxx
left cartridge => HP-ASIC to warm
(>125C)
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
Ultimail
ISS international service support
email: iss@francotyp.com
page 15
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E127
xxx2 xxxx
xxxx xxxx
left cartridge => HP-ASIC to hot (<142°C)
machine is blocked
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
E127
xxx4 xxxx
xxxx xxxx
left cartridge => calibration failed
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check the temperature on the cartridge Service mode->
cartridge info. If the temp is 0°C please exchange the splitter board and/or (RDS mover) .
see tecchnical bulletin #1
E127
xxx8 xxxx
xxxx xxxx
left cartridge => print voltage to low
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check temperatur on the cartridge in service mode => cartridge
info
search for your subcode…
see also technical bulletin #1
E127
xxxx xx1x
xxxx xxxx
right cartridge => print voltage to high
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check temperatur on the cartridge in service mode => cartridge
info
see also technical bulletin #1
E127
xxxx xx2x
xxxx xxxx
right cartridge => low voltage
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
E127
xxxx xx4x
xxxx xxxx
left cartridge => contact problem
Cotact problem /Cartridge failer
=> C: exchange cartridge, install again
=> T: run contact test in Service mode
search for your subcode…
see also technical bulletin #1
E127
xxxx xx8x
xxxx xxxx
right cartridge => identification error
=>C: install cartridge again, exchange the cartridge
maybe wrong or non FP cartridge?
=>T: run contact test in service mode and clean the contacts
E127
xxxx xxx1
xxxx xxxx
right cartridge => HP-ASIC to warm
(>125C)
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
Ultimail
ISS international service support
email: iss@francotyp.com
page 16
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E127
xxxx xxx2
xxxx xxxx
right cartridge => HP-ASIC to hot
(<142°C) machine is blocked
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, exchange the pen driver board (RDS mover)
E127
xxxx xxx4
xxxx xxxx
right cartridge => calibration failed
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check the temperature on the cartridge Service mode->
cartridge info. If the temp is 0°C please exchange the splitter board and/or (RDS mover) .
see tecchnical bulletin #1
E127
xxxx xxx8
xxxx xxxx
right cartridge => print voltage to low
=> C: exchange cartridge, install again
=> T: run contact test in Service mode, check temperatur on the cartridge in service mode => cartridge
info
search for your subcode…
see also technical bulletin #1
E127
xxxx xxxx
x1xx xxxx
left cartridge => incorrect (different)
machine number on the CP chip
=> C: install cartridge again, exchange cartridge
maybe the customer has a mymail cartridge in use?
=> T: run contact test in service mode
calibrate cartridge in service mode again.
E127
xxxx xxxx
xxx x1xx
right cartridge => incorrect (different)
machine number on the CP chip
=> C: install cartridge again, exchange cartridge
maybe the customer has a mymail cartridge in use?
=> T: run contact test in service mode
calibrate cartridge in service mode again.
E127
xxxx xxxx
xxx xxx1
right cartridge => incorrect CP-chip (or no
chip, nonFP?) manipulation?
=> C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxx2
left cartridge=> CRC (checksum) error
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxx3
right cartridge => wrong CP chip type
(logictype)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxx4
right cartridge => wrong CP chip type or
wrong chip type data in the cartridge
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
Ultimail
ISS international service support
email: iss@francotyp.com
page 17
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E127
xxxx xxxx
xxx xxx5
right cartridge => incorrect CP-chip (or no
chip) manipulation?
=> C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxx7
right cartridge => Chip protection failer
(PIN)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxxB
right cartridge=> wrong command (sw
failer)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx xxxC
right cartridge = incorrect data in the CP
chip
(incorrect ink level)
=>C: install cartridge again, exchange the cartridge
maybe wrong or non FP cartridge?
=>T: run contact test in service mode and clean the contacts
E127
xxxx xxxx
xxx xxxD
left cartridge => Ink counter reports ink
low
=> C: exchange cartridges
=> T: run contact test in service mode
The machine count the ink (in pikpliter),
which is used for all cleaning and printing
E127
xxxx xxxx
xxx1 xxxx
left cartridge => incorrect CP-chip (or no
chip, nonFP?) manipulation?
=> C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx2 xxxx
left cartridge=> CRC (checksum) error
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx3 xxxx
left cartridge => wrong CP chip type
(logictype)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx4 xxxx
left cartridge => wrong CP chip type or
wrong chip type data in the cartridge
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
Ultimail
ISS international service support
email: iss@francotyp.com
page 18
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E127
xxxx xxxx
xxx5 xxxx
left cartridge => incorrect CP-chip (or no
chip) manipulation?
=> C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxx7 xxxx
left cartridge => Chip protection failer
(PIN)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxxB xxxx
left cartridge=> wrong command (sw
failer)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxxC xxxx
left cartridge => wrong data on the
CP-chip (ink level information)
=>C: exchange Cartridge, install cartridge again
=> T: run contact test in service mode
E127
xxxx xxxx
xxxD xxxx
left cartridge => Ink counter reports ink
low
=> C: exchange cartridges
=> T: run contact test in service mode
The machine count the ink (in pikpliter),
which is used for all cleaning and printing
E128
Unable to determine optimum print
voltage (TTOE) during print cartridge
calibration.
Contact problems / ink cartridge error / swapped cartridges
=> C: insert Inkjet cartridges again, replace ink cartridges
=> T:: check contact properties in service mode
Does the cartridges get initialized many
E129
Drive for letter transport is not ready.
Microswitch is not triggered correct by letter transport with counter rollers beneath the Inkjet cartridges
=> C: pull out letter transport and insert it again (please refer to section removing letter jams of ultimail
operator manual)
=> T: trigger microswitch manually on the rear right side of the insertion area for the letter transport,
press 'Start', clear error message, and check if drive starts
E130
The letter to be franked was too
short.1&2: Interval LS3_Open LS3_Close too small.
=> C: Impression to long, maybe Advert +short message selected by lable print?
E131
This error is not generated.
Contact problems / ink cartridge error => C: insert Inkjet cartridges again, replace ink cartridges
Ultimail
ISS international service support
email: iss@francotyp.com
page 19
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E132
The sealer drive is not running.
Microswitch of sealer is not toggled correct
=> C: release roller transport of sealer and close it again
E133
The feeder drive is not running.
Microswitch of sealer is not toggled correct
=>C: release roller transport of sealer and close it again
Feeder Power connection unpluged?
Print cartridges not recognized.
Subcode 1: Print cartridge status
information
Subcode 2: Consumable protection status
information, as under E127
Eventually contact problems
E135
Unknown print cartridges detected.
Contact problems / ink cartridge error / swapped cartridges => C: insert Inkjet cartridges again, replace
ink cartridges / E: check contact properties in service mode
E136
The print cartridges are not configured.
1: Print cartridge status information, as
under E127
2: Consumable protection status
information, as under E127
contact problems/ cartridge error/ mymail cartridge?
E137
Print cartridges are empty.
1: Print cartridge status information, as
under E127
2: Consumable protection status
information, as under E127
=>C: rplace cartridges again, repeat calibration
E138
Error E138 is an error in LS2 and LS3
timing.
Subcode 1: 0028 LS2 has closed, although LS1 has not yet closed (ErrNoLS1BeforeLS2)
Subcode 1: 000F Interval LS2_Close LS3_Close too small (less than 500 encoder pulses)
Subcode 1: 0010 Interval LS2_Close LS3_Close too large (more than 750 encoder pulses)
Subcode 2: Interval LS2_Close LS3_Close in encoder pulses
Example: E138, Subcode 1 000F, Subcode 01D0
Interval LS2_Close LS3_Close too small
Causes: LS2 closed slowly or no encoder pulses (dirty encoder)!
E134
=> C: insert Inkjet cartridges again
=> C: exchange cartridges
T: run contact test in Service mode
Letters are too short or too long / sensor error
=>C: use specified letters, feed letter again
E139
Ultimail
Communication error to print cartridges or
print process incorrectly performed.
1: Print cartridge status information, as
under E127
2: Consumable protection status
Contact problems / ink cartridge error / swapped cartridges
=>C: insert Inkjet cartridges again, changee ink cartridges
E: check contact properties in service mode
ISS international service support
email: iss@francotyp.com
page 20
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E140
Unable to transfer data to print cartridges.
1: Print cartridge status information, as
under E127
2: Consumable protection status
information, as under E127
Contact problems / ink cartridge error / swapped cartridges
Unable to detect label properly.
=>C: check labels, eliminate label jam (remove label dispenser subject, unlock letter transport (please
refer to section removing letter jams of ultimail operator manual))
E141
=>C: insert Inkjet cartridges again, replace ink cartridges
=>T: check contact properties in service mode
bad CP-Chip aplikation, PBD clean, check, exchange
Use FP Label only!
=>T: sw update 03.01.02 and higher more details TI 17a. Because the lable handling becomes
modified.
E142
E143
Unable to calibrate label dispenser
sensor.
Sensor could not be calibrated - a label covers it =>
Unable to read data from print cartridges.
Contact problems / ink cartridge error / swapped cartridges
=>C: if necessary remove label from label passage, switch ultimail off and on again
=> C: insert Inkjet cartridges again, replace ink cartridges
=> T: SW update min.: 02.39.07
E144
E146
Print voltage has fallen to an
unacceptable value.
Polyswitch has triggered. Short circuit or to high current load to the or on the PenDriverBoard
Errors occurred during printing process.
Contact problems / ink cartridge error / swapped cartridges
Subcode 1:cartridge-statusinformation
subcode
=> C: insert Inkjet cartridges again, replace ink cartridges
=>T: Check PDB, PDB cable, and mainboard
=> T: PDB's check, clean, change
run contact test in service mode
print voltage to low/high it is not s cartridge problem
see E146
Ultimail
ISS international service support
email: iss@francotyp.com
page 21
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
E147
temperature of print cartridges to high
remedy
Unacceptable temperature of print cartridges (> 55°C) is detected. Print quality will be effected.
Subcode 1 show temperature of cartridge 1 at Pen 1 [in deg]
Subcode 2 show temperature of cartridge 0 at Pen 0 [in deg]
This error can be reported during longer print pauses.
It may be caused by:
- wrong working temperature sensor at splitter board
- wrong temperature calibration of cartridges. e.g. if a cold cartridge was inserted in a warm machine.
Please perform change cartridge without changing chartidges - temperature calibration of cartridges is
performed again.
- If cartridge is empty also high temperatures are caused.
- During the print head startup test, faulty resistors on the cartridge becomes also reported as error
E148
The encoder data for the letter transport
drive is faulty.
=>T: check, clean, change encoder.
Check encoder cable (shifted imprint?)
Subcode 1: Number of encoder defects
E149
The feeder is not switched on
power cord of the feeder unit is not connected
=>C: check the power cord
E150
The sealer is not switched on
=> C: check connecting cable
E151
Label incorrectly positioned in machine
C: check labels, eliminate label jam (draw label dispenser, unlock letter transport (please refer to
section removing letter jams of ultimail operator manual))
Use FP Label only!
=>T: sw update 03.01.02 and higher more details see TI 17a
E152
Ultimail
No more letters are in the feeder for list
print so the list print is aborted.
=> C: insert more envelopes and repeat list printing
ISS international service support
email: iss@francotyp.com
page 22
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
E153
Warm up the cartridges missed, please
execute 'change cartridges' !
Contact problems / faulty Inkjet cartridges / current not sufficient / bad temperature calibration => Error
message that the ink cartridges could not be heated up to the required pulse warming temperature
(standard: 45 C). Heat up cartridges: before print start, before clean intensive
E154
Sensor of ambient temperature is defect!
Please call FP Service!
I²C temperature sensor on splitter board is defektive, connector and cable to I²C temperature sensor
defective
=>T: I²C temperature sensor provides no measurement value. Check connector and cable see
cartridge temp. If =0 then replace splitter board with I²C temperature sensor.
E155
Letter to short! Please remove SMS text
or advert!
Imprint is longer than (last) letter =>
E156
Unable to position (reference) print
cartridge direction.
Stops for GKBK-RDS too close to sensor => Adjust stop for RDS mover
E157
Read and write errors with consumable
protection on right ink cartridge (pen0)
contact problem => check / improve connection with cartridge
E158
Read and write errors with consumable
protection on left ink cartridge (pen1)
=>C: contact problem => check / improve connection with cartridge
=>T: test/clean/change PenDriverBoard
F100
This error is not generated.
no Aktion info only
If this error appers please contact your hotline and create a support request
F101
Error occurred in 1K-X modem protocol
=> T: check PC COM port settings (COM 1-4? baudrate: 115200)
=> T: clean, test, change PenDriverBoard contact
Can only be happen if a SSM-PC is
connected
Ultimail
ISS international service support
email: iss@francotyp.com
page 23
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
F102
Interface card not found
=> C: confirm Error, start working, call Service, because after the next power up the message appears
again.
=>T: Check if the optional secound interface card is present.
1) card is installed, message appears -> Check UART settings, exchange interface card
2) Card didn't exist, message appears -> Enter service mode -> optional devices -> deactivate
interface card
3) make software update 02.36.00 or later (see technical bulletin #11)
F103
The ReadyMode in Serial Task is not set
=> Send a BatchData Request
F104
configuration problem serial interface
The port of Karat PC is equal the Serial-Protocol-Port
F106
configuration problem serial interface
Configuration has to be changed.
Karat has to be configured to serial OIC interface (Uart2).
G039
Germany only!!
BZL (special postal services in Germany)
No continuously number availeble
Run teleset
G101
xxxx xxx1
1000 0001
Postage calculation provides no valid
product information to print data
preparation.
No postage rate table available
C: Load rate table or run TELESET with FRANKIT meter
G101
xxxx xxx1
1000 0002
Error in print image data: although SSB is
active, no picpart with offset
OFF_BZL_INDICATOR is contained in
the cliché data!
Wrong cliché data loaded
E: Load FRANKIT cliché data complete new
Only notification of task manager, that
conversion of cliche data to 32-bit
structure is necessary first when starting
the system and the print data task
requires some time for this. The user does
=>C: wait maybe switch on the meter again
G104
Ultimail
ISS international service support
email: iss@francotyp.com
page 24
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
G200
No print image data available!
=> T: install complete images (mabe FP-card is nessecary?)
G202
Unrecognized offset value in print image
data!
This can be caused by lastest cliché data that will not match to franking - machine software.
G217
Error in print image datan! Print image
height (Pic head) too large!
=> T: load ultimail clischee! Maybe tryed to load a clischee of any other machine type?
G227
Error in print image data! No
PIXELHEADER with associated type
found!
=> T: load full image again
G229
Error in print image data! No
PIXELHEADER for associated type and
number found!
=> T: load clischees again (advert and endorsements)
G232
Error in print image data! No
PIXELHEADER for type of mail number
found!
re load correct endorsements /Logo data (send a new chip card)
G233
Error in print image data! Unrecognized
code (RUN LENGTH CODING) in pixel
data!
=>T: run sensor test print start sensor defect? Change main board
G234
Error in print image data! LIMIT of
postage value less than DIGITS in print
image data!
=> please select a amount which is printable with your configuration (4 or 5 digits)
G235
Error in print image data! CHARSETID not
available!
=> maybe a clichee of a different country version or machine type loaded?
Please order a new clichee card
Ultimail
Remedy:
1.) Software update of franking machine
ISS international service support
email: iss@francotyp.com
page 25
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
G237
There are too many logos to be loaded!
Select fewer or delete some in advance!
=> Please think about the max. number of clichees
G238
There are too many types of mail to load!
Select fewer or delete some in advance!
=> Please think about the max. number of clichees
G239
Error reading print data from chip card!
Insert card again!
Chip card was inserted the wrong way round
G240
Error in print image data. License string 1
is too long! Please ring FP service dept!
=> T: load full image again
G242
Error whilst checking print image data!
Please call FP service dept.. An error
occurred during MAC checking of cliché
data.
=>E: check Security Module. If it works OK then load another full image via chip card or PMD
customizing.
G243
Error in cliché data! Please call FP service
dept.
=> T: load another full image via chip card or PMD customizing.
G244
Error in cliché data! Please call FP service
dept.
=> T: load another full image via chip card or PMD customizing.
G246
Print image data structure error!
MODEL_ID2_STR has more characters
than provided in picpart
US_TWO_DIGIT_ID
=> E: load another full image via chip card or PMD customizing or check country parameters and load
new ultimail SW
G247
Print image data structure error! Limit of
PicPart US_TWO_DIGIT_ID
(MODEL_ID2_STR) is 0
=> E: load another full image via chip card or PMD customizing.
Ultimail
=> C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure
point
ISS international service support
email: iss@francotyp.com
page 26
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
G250
Print image data structure error! Width of
pixel header does not fit in PicPart
=> T: load another full image via chip card or PMD customizing.
(Clischee data are to big)
G251
Print image data structure error! Height of
pixel header does not fit in PicPart
=> E: load another full image via chip card or PMD customizing.
G252
Error writing to chip card! This error can
occur when loading cliché data (e.g. town
circle), if errors occur on the chip card
when deleting the segment after
successful loading.
=> E: Load Registration Post Office once again
G253
Error loading part print images, not
enough space available in FLASH!
=> C: Delete adverts or mail services (endorsements)
G254
Error checking cliché data CRCs
=> E: load another full image via chip card or PMD customizing.
G255
Error checking number of endorsements
of cliché data, maximum 8
(MAX_ENDORSEMENTS -1) are allowed
Cliche data with too much postal endorsements have been downloaded when PMD customizing or
when downloading a full image! => E: load another full image via chip card or PMD customizing.
G256
Interval between two letters too small so
that the SSB ident no. could not be
requested and processed yet.
Separation error / LS2 defect / too fast feeding in sealer and stand alone mode => C: feed letters with
larger clearance / E: LS2, check separator in feeder unit
G257
Print image data error! Please call FP
service. The error occurred while verifying
the MAC of the cliché data. The service
SVC_VERIFYMAC of the security task
could not be opened!
1. the security device (SD) has not the state VALID, AUTHORIZED, or INITIALIZED, or
2. the security device (SD) is not plugged correct. In this case another error will be displayed that
clearly refers to the security device (SD)!
1. INITIALIZE, REINITIALIZE, or AUTHORIZE the security device (SD), or
2. plug the security device (SD) tightly.
G258
Print image data error! Please call FP
service. A communication error to the
security device (SD) occurred while
verifying the MAC of the cliché data.
The security device (SD) is not plugged correct or the contacts are corroded! => Plug the security
device (SD) tightly and perhaps clean the contacts of the connectors. Then the HS-Loop must be
closed in service mode and a PVD >= 0 must be performed (because error message C026 is
displayed).
Ultimail
ISS international service support
email: iss@francotyp.com
page 27
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
G259
An error occurred while generating the ID
matrix code. It may only occur under
development.
Too much data provided for barcode => Inform R&D department
G260
Error while printing the SSB list because
the corresponding OFFSET-PicPart is not
available in the cliché data.
No or false cliché data were loaded => Correct the complete cliché and download it
G262
SD error! The lenght of the Vendor ID is
not like required (CANADA-Post want to
have 5 digits)
wrong setting in the CPS-Server = sw update and a PVD
G263
cliché data failure - slogan
slogan exceeds definition of MAX_LINES_OF_SLOGAN
root causes:
wrong generation of complete cliché
remedy:
perform complete cliche update
G264
cliché data failure - slogan
slogan exceeds definition of MAX_COLUMNS_OF_SLOGAN
root causes:
wrong generation of complete cliché
remedy:
perform complete cliche update
G265
cliché - FM software release missmatch
cliché release requires higher FM software release
Remedy:
1.) first perfom a franking machine software update
2.) then download new complete cliché data
G266
Charaterset for slogan not availabe
Charaterset for slogan not availabe.
Remedy:
perform complete cliché update
Ultimail
ISS international service support
email: iss@francotyp.com
page 28
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
G267
string too long
remedy
String is too long. String can not be printed. Please call FP-service.
The string-verification is activated at chliche version >= 01.05.00.
Root cause:
bad chliche data
Remedy:
perform update of cliche data
G300
Cartridges not overlapping!
=> C: adjust cartridges again
Subcode 1: Vertical spacing of cartridges
in nozzles
H100
No communication with security module!
Security device is not plugged in the right way or is defect.
Remedy:
Verify position of security device and perform selftest to check functionality.
H101
Communication error to security module
Security Module not plugged / defective
technician
1.) plug Security Module
2.) after consultation with national second level support => replace mainboard
H102
Security module: Self test failed!
=> exchange the security modul -> a new postal registration is required
H103
Security device (SD): Accounting service
cannot be closed!
Security device not plugged / defective
=>T: plug security device
H104
0000 0004
0003 0227
Security module: Command cannot be
performed!
PSD is in the state: authorized and the
HS-Loop is open.
Please reset HS-Loop in the service mode
H104
0000 0004
0006 0212
Security module: Command cannot be
performed!
Please reset HS-Loop in the service mode and perform zero reset (Teleset).
Ultimail
ISS international service support
email: iss@francotyp.com
page 29
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
H104
Security module: Command cannot be
performed!
Security Module not plugged / defective
If: 00000001 00010216, then HS-LOOP is
not closed
=>T: plug Security Module again
reset HS-Loop
exchange main board
SD test/exchange
H106
Security module: Software SD-Software
not loaded! Unable to read from serial
port.
=> T: is possible during a sw upgrade into the PSD. Check connection between FM and PC, check
COM port settings (COM 1-4, baudrate 115200)
H110
Security module: Software in security
module too old. Service must load new
software to security module!
=> T: Machine must be in the state: Initialized after that the PSD SW must be upgraded by using the
SSM-PC (FP-card is required)
H111
Subcode 1 and 2 - 00000000 00000000,
then Security Module: error should only
occur under development, e.g.: unknown
accounting mode implemented in revision
02.00.00: NORMAL_ACCOUNTING,
=> check SM or exchange
H112
not allowed postage value
The Security Module has to account a postage value that is not allowed according to the country
parameters (e.g. 0 in the Netherlands).
Please select an other value (product) and try again.
Can also be caused by:
1.) out of date franking machne software
2.) faulty rate table
H113
Communication error with security device
(SD). Please call FP service!
=> Usually the operator cannot eliminate the deficiency. The error parameters provide more details:
P1: bit 16…31: service ID, bit 0…15: error type
P2: bit 16…31: error context, bit 0…15: error no.
H114
Communication error to FP data center.
Please call FP service!
Usually the operator cannot eliminate the deficiency. The error parameters provide more details:
P1: bit 16=31: service ID, bit 0=15: error type P2: bit 16=31: error context, bit 0=15: error no.
HS-loop check/reset => PVD
H115
This error can only occur with FRANKIT
(Germany) ultimails. After switching the
FM on this test is done in the states
INITIALIZED, AUTHORIZED, and VALID.
The error is caused if different ultimail
When registering the ultimail at the server its model name was entered wrong or a wrong mainboard
was used => Replace PSD
Ultimail
ISS international service support
email: iss@francotyp.com
page 30
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
H116
In Canada muss die CreationTime
innerhalb eines Batches (zwischen zwei
PVDs) aufsteigend sein. Dies ist hier nicht
der Fall. Hinweis für Benutzer
Zeitzone umgestellt,
Umschaltung von Sommer- auf Winterzeit => PVD durchführen
H117
illeagal SD change
illeagal SD change at LMR-variant ((LRM - LocalResetingMachine)
SD-ID of new SD is unknown and registers r1 - r4 are not zero.
remedy:
Delete pin ta servicemode ( 1930-DELETE LRM-PIN)
I150
Insufficient access authorizations (card
level)
=> Please use chip card with higher access rights (Dealer-, FP-, Factory card)
I152
Unable to create more accounts ...
=> are the max number of cost account already in use? In the ultimail60 is it possible to by a code
which expand the number of 10 accounts to 50.
L100
Chip card read error!
Chip card was inserted the wrong way round
=>C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure
point
M039
like G039
It's a German BZL feature -> no more
serial no. available
Run teleset
M100
Unspecified error during postage
calculation, returned by postage table
=> C:T: load rate tabel again
M101
Postage table returning Entry not found
error
=> select other product, load new rate table
M102
Postage table returning “Weight range
exceeded” error
=>C: Please install a new valid rate table, depending the country version, load it via chip card or
remote via modem.
Ultimail
ISS international service support
email: iss@francotyp.com
page 31
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
M103
Postage table returning Value too high“
error
=> load actual rate table
M104
Postage table returning Invalid
combination” error
=> C: load valid rate table
M110
Loading postage tables: Error reading
new postage table from chip card
=> C: check chip card, insert chip card with chip to the bottom, insert chip card beyond the pressure
point
M114
Error initializing current postage table
when starting system or after loading
=> C: load postage rate table again
M126
The zip code entered is not recognized.
=>C: select valid ZIP code
(US only)
M127
Error in postage calculation: Below
minimum weight for this type of mail.
=> C: select valid produkt or use correct weight
M128
Error in postage calculation: Product code
could not be calculated. Franking not
possible.
Product code could not be calculated. So franking is not possible. The reason of the error is a faulty
postage rate table. => Postage rate table must be updated.
Maybe there is a incorrect Memory setting programmed. please re-program the memory for a valid
product.
M129
Error in memory postage calculation:
This selected service cannot be
saved.
The memory entry cannot be stored because the selected service is not valid for the memory.
M130
The new rate table does not contain
a shortcut table. Memory entries
cannot be initialized.
Please contact FP service dept!
Download of postage rate tables: the just loaded rate table contains no or an empty shortcut table.
Thus the memories cannot be initialized. => Postage rate table must be updated.
Ultimail
ISS international service support
email: iss@francotyp.com
page 32
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
M131
The active rate table does not support
SSB.
Please run TELESET to download the
latest rate table.
Operator tried to print SSB with a rate table that does not support SSB. => Download current rate
table.
M132
SSB: ident numbers must be printed or
transferred
Germany only
Germany only
M133
The selected product cannot be franked in
the mode Reply Mail.
The operator tried to frank a mail piece in the mode Reply Mail. According to German Post AG this is
not possible.
=> C: Change product selection or deselect mode Reply Mail.
M134
Germany only
Germany only
M135
Incorrect dimensions for the selected
product. Weight, lenght, high is to big
=> no actions possible
M136
new rate table is activated
The new rate table is valid. Please print the SSB list NOW and then restart the machine again.
Frankit only: The SSB list must be deleted before the selected operation can be executed.
M137
rate calculation - FSA-failure
Error when determining the Rate Code. Please check the entered FSA for the destination.
At this time only valid for Canada: an error occurred when calculating the rate code. The entered FSA
(forward sortation area) was invalid.
The correct FSA of the destination must be entered again. Please note that it is in the form ANA (A…
alphabetic character; N…numeric character), e.g. J0M.
Ultimail
ISS international service support
email: iss@francotyp.com
page 33
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
M138
rate calculation - product not allowed
remedy
Your selection will not be supported in the current mode of the meter.
At this time only valid for Canada: the selected product cannot be metered in the current mode of the
meter. Actually only applies to Return Postage Prepaid and Statement of Mailing in the specimen
mode.
M139
error by postage calculation
clean LS1 and 2, clean the lable dispensor guide and sensor.
This error appears in combination with E113,E117 E126,E129.
N100
General communication error with internal
scales
=> T: check scale cable connection
N102
The weight is too high: Either the
maximum permissible load of the internal
scales is exceeded or the maximum load
specified in the variant switch
VARIANT_STW_WEIGHT_MAX has
=>C: Don't use more than 5Kg (10lbs) on the scale platform
=>T: calibrate scale
N103
Weighing cell reporting Weight is too low
=> C: Tara scale by restart FM
=>T: calibrate scale, exchange weight cell
N104
Unable to find internal scales
=> T: 1) check cabel to the splitter board. 2) Exchange splitter board (the splitter board is defect if no
temperature is displayed in the service mode (service mode->print settings-> cartridge info-> UG
Temp). 3) exchange scale device.
4) If there is no internal scale installed please deselect scale in service mode.
N105
Weighing cell reporting unknown error
code
The received errorcode can not handled by franking machine software.
O002
No answer from the TDC/FPI modem side
Check the phone connection to the TDC/FPI via telephone.
O003
no dial tone
check the phone system (maybe digital?)
Ultimail
Remedy
Update franking machine software
ISS international service support
email: iss@francotyp.com
page 34
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O004
Line is busy.
Customer: try again
T: PBX system use wrong tone
O006
O007
XXXX XXXX
0000 0000
no connection
check phone system, try to contact the TDC/FPI via telephone
general error by connecting the FPI
modem not found
The internal modem is not found. Switch off/on the machine, during the power up you will find
additional modem errors.
If the remote data sending is impossible, please ask the customer for the errors which occur during the
power up.
In the system data (report) you will find additional info about the modem state.
possible reason:
- defect modem
- cable modem-> main board
- main board defect
O007
XXXX XXXX
0000 0001
general error by connecting the FPI
no dial tone
Please check the modem configuration
1) dial parameter
2) extension #
For this setting the MASTER card is required
It also can be a defect modem cabel. Please check following things:
1) correct connection on the FM side
2) correct connection on the phone system side
At least check if there is a dial tone present (delivered) on the phone system
possible reasons are:
1) phone connection is death
2) it is a multiple connecting system and one of the other devices switch off the dial tone (only
Germany???)
O007
Ultimail
XXXX XXXX
0000 0002
General error by connecting the FPI(connection is bussy)
Try it later again
ISS international service support
email: iss@francotyp.com
page 35
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
O007
general error by connecting the FPI- no
answer (modem)
XXXX XXXX
0000 0003
remedy
Please check the modem configuration
1) dial parameter
2) extension #
3) phone #
For this setting the MASTER card is required
It also can be a defect modem cabel. Please check following things:
1) correct connection on the FM side
2) correct connection on the phone system side
At least check if there is a dial tone present (delivered) on the phone system
possible reasons are:
1) phone connection is death
2) it is a multiple connecting system and one of the other devices switch off the dial tone (only
Germany???)
O007
XXXX XXXX
0000 0004
general error by connecting the FPI- no
dial tone detected (modem)
Please check the modem configuration
1) dial parameter
2) extension #
For this setting the MASTER card is required
It also can be a defect modem cabel. Please check following things:
1) correct connection on the FM side
2) correct connection on the phone system side
At least check if there is a dial tone present (delivered) on the phone system
possible reasons are:
1) phone connection is death
2) it is a multiple connecting system and one of the other devices switch off the dial tone (only
Germany???)
O007
XXXX XXXX
0000 0006
General error by connecting the FPI
Please try again. Please look for further diagnostic messages. If the error can be reproduce, please
contact your hotline or nat. second level support (please send a support request -> SKD)
O007
0000 0001
0000 0005
=> proxy error
please contact your FPI admin
O007
0000 0002
0000 0005
=> no connection to the FPI
check phone cable, dial parameter, programmed phone no., PBX system.
try to get a outside connection (mayby to your cell phone) by reprogram the TDC phone no. temporally.
Ultimail
ISS international service support
email: iss@francotyp.com
page 36
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O007
0000 0003
0000 0005
=> communication error between FM ->
FPI
bad (noise) phone line?
O007
0000 0004
0000 0005
=> Service not availeble
test the FPI (TDC) by calling the TDC no. via phone, find out if a modem is running on the TDC side
O007
0000 0005
0000 0005
=> service is not finished
modem didn't hang off
O007
0000 0006
0000 0005
=> NAK received from FPI
contact your FPI admin
O007
0000 0007
0000 0005
=> Buffer overflow
contact your FPI admin
O007
0000 0008
0000 0005
=> error during sending
FM didn't be able to send data. May be phone line get interupted?
O007
0000 0009
0000 0005
=> error during receiving data
FM didn't receive data from the FPI. May be the phone line get interupted?
O007
0000 000A
0000 0005
=> SD communication error
Please contact hotline and send a support request
O007
0000 0010
0000 0005
=> protocol error
please contact the TDC/IBIP admin.
Ultimail
ISS international service support
email: iss@francotyp.com
page 37
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O007
0000 0011
0000 0005
=> invalid reset amount
please choice a other amount (steps of 10)
O007
0000 0012
0000 0005
=> unvalid transaction
Please contact the TDC/IBIB admin.
O007
0000 0013
0000 0005
=> Krep overflow
A good working phone connection between FM -> FPI becomes interupted more than 10 times. Go into
the service mode and reset the Krep counter
O007
0000 0014
0000 0005
=> wrong machine ID
machine back to FP
O007
0000 0015
0000 0005
=> SD state is unvalid
Restart machine and try again
O007
0000 0016
0000 0005
=> unvalid protocol version
FPI and SD use different protocoll versions
Check the TDC phone no. which is programmed
O007
0000 0017
0000 0005
=> new phone no.
is impossible in real life, because the phone no. becomes updated automatically
O007
0000 0018
0000 0005
=> meter is unknown in the TDC
meter is not released by the postal authority? withdran? scraped?
O007
0000 0019
0000 0005
=> Meter is not registered as valid in the
FPI
contact your FPI admin
Ultimail
ISS international service support
email: iss@francotyp.com
page 38
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O007
0000 001A
0000 0005
=> Meter is not released by the postal
authority
contact your FPI adim
O007
0000 001B
0000 0005
=> Meter is sign off
contact your FPI admin
O007
0000 001C
0000 0005
=> no money availeble
contact your FPI admin
O007
0000 001D
0000 0005
=> customer/account isn't registered in
the FPI
contact your FPI admin
O007
0000 001E
0000 0005
=> Meter is locked on the FPI side
contact your FPI admin
O007
0000 001F
0000 0005
=> R1 isn't correct
contact your FPI admin
O007
0000 0020
0000 0005
=> R2 isn't correct
contact your FPI admin
O007
0000 0021
0000 0005
=> R3 isn't correct
contact your FPI admin
O007
0000 0022
0000 0005
=> invalid reset amount
use an other reset value (steps of 10)
Ultimail
ISS international service support
email: iss@francotyp.com
page 39
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O007
0000 0023
0000 0005
=> R3 overflow
normally impossible! contact your FPI admin
O007
0000 0024
0000 0005
=> wrong teleset keys (Kfix0, Kfix1, Kvar)
Meter (SD) must back to FP
O007
0000 0025
0000 0005
=> FPI system error
contact your FPI admin
O007
0000 0026
0000 0005
=> FPI isn't availeble
check FPI by calling via phone, find out if a modem is connected
O007
0000 0027
0000 0005
=> wrong rest value
choice an other reset amount (steps in 10)
O007
0000 000A
0000 0005
=> HS-Loop is open
Enter the Service mode and reset the HS-Loop. If it is not successful, please check the security switch
on the back panel (main board), SD Interface connection and the print data cable.
O008
FM is unknown in the TDC/FPI
Please contact the TDC/FPI admin.
O041
The money which is required for a PVD is
not availeble.
The customer have to use a lower amount
Hotline: Please ask your Data center admin about a valid PVD amount.
This warning is in use from SW 03.01.02 and higher
O042
invalid PVD amount
Customer have to use a lower PVD amount.
Hotline: Please ask your Data Center admin about the max. PVD amount.
This warning will be supportet from SW 03.01.02 and higher
Ultimail
ISS international service support
email: iss@francotyp.com
page 40
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O043
TDC message: Meter is is locked
Hotline: Please ask Data center admin about the locking
This warning is supported from SW 03.01.02 and higher
The Data center message means that the
HS-loop is open. The display message is
identical with error O007.
Check for the reason of the open HS-loop (Reset in Service Mode, open switch on the main board,
disconnected SD, disconnected print cable?)
FrankIT (Germany) or Central Server
(CAN) is locked. There is a data
exchange between the Servers in
process.
Please contact the server admin.
Please try install or PVD later again.
O045
It's FRANKIT (DEU) and Central Server
(CAN) only: During a remote service a
communication problem accour. The
customer have to call the FP service.
Maybe the FPI server is locked
Call service! The service have to contact the R&D or the Server admin. The reason can only find by
the error context which is part of the subcode 2.
O046
It for FrankIt/ Central Server (Germany /
Canada only)
The postal authority did not relase the FM
allready
wait for the postal aproval
O047
It for FrankIt/ Central Server (Germany /
Canada only)
The postal authority did not complete the
relase of the FM. Data are not complete.
Please try again next day
O048
An error occured by using remote
services.
Please call FP-Service (former diagnosis code H113)
Cause can only be determined by subcodes.
O100
Default value for teleset too low
Please select a higher reset value (in 10 imcrements)
O101
Default value for teleset too high
Please select a lower reset value (in 10 imcrements)
O044
O045
01130139
Ultimail
This error message is supported from SW 03.01.02 and higher
ISS international service support
email: iss@francotyp.com
page 41
created : 20.11.2007 19:33 Uhr
diagnostic- subcode1
code
subcode2
diagnostic message
remedy
O102
Step width for teleset not observed
Please select an other reset value (in 10 imcrements)
O103
Register 1 overflow
Normally impossible
O104
Register 3 overflow
Normally impossible
A new SD is required
O117
FM was locked by dealer, unlock possible
by entering unlock code
=>T: unlock is possible in service mode. Unlock code is required
call international service
ISS international service support
email: iss@francotyp.com
page 42
created : 20.11.2007 19:33 Uhr
Download PDF