Huawei FT2260 Quick Start English

Huawei FT2260 Quick Start English
HUAWEI FT2260
Home Phone Connect
Quick Start
Introduction
Top View

Note:
The figures are only for your reference, the actual shape and color of the product may
differ slightly.
7
8
9
10
2
3
4
5
6
1
1
Power on/off switch
6
Antenna port
2
Telephone port 1
7
Signal strength indicators
3
Telephone port 2
8
Battery indicator
4
USB port*
9
Power indicator
5
DC 12V power port
10
Voice mail indicator
* Note: Never place a USB-based device into the USB port of the Home Phone Connect under any
circumstances. Doing so may damage the device and negate its warranty. The port was designed
for diagnostic purposes only; it is not intended for customer use.
Rear View
4
1
2
3
1
Battery cover
3
Battery slot
2
Battery port
4
Wall-mounting brackets
Installation
Installing the Battery

Note:
 If the ambient temperature exceeds the temperature allowed for charging, the device
stops charging the battery.
 If connected to the power adapter, the device automatically charges the battery and
stops charging when the battery is fully charged.
 Remove the battery if the device is not in use for a long time.
 If the battery has not been used for a long time or if the battery runs out of power, the
device's indicators may not turn on as expected when the battery is charging. This is
normal. The device can be powered on after the battery is charged for a while.
 Generally, the device sources its power from the line power supply using the power
adapter. It sources its power from the battery only when there is a power failure or no
power outlet is available.
 The battery supplies power for only a limited period. Ensure that the battery has been
fully charged before using the device without the line power supply connected.
Connect the battery cable to the battery port, ensure that the battery terminals are not reversed,
and place the battery in the battery compartment.
Installing the Antenna
1.
2.
Power the device off.
Connect the indoor antenna to the antenna port as shown in the following figure, and screw on
the antenna until it is securely connected.
Installing the Power Adapter
Under normal operation, the Home Phone Connect is powered from an A.C. power outlet using the
power adapter that is included with the device.
Power the device off, connect one end of the power adapter to the DC input port and the other to
an A.C. power outlet.

Note:
Use the battery only when there is a power failure or no power outlet is available. Ensure
that the battery has been fully charged before using the device without the A.C power
adapter connected.
Connecting the Device to a Telephone
The device provides two telephone ports. The ports provide connection to a single telephone
number assigned to the device by your service provider.
1.
2.
Unplug your telephone from your wall's telephone jack.
Do not plug Home Phone Connect into your telephone wall jack, this configuration is not
supported unless you have taken steps to disconnect the landline wires coming into your
home.

Note:
 The telephone cord is not included.
 The device and telephone cord are for indoor use only.
 Only corded telephones or cordless base stations connected directly to the Home
Phone Connect will receive service.
 If the Home Phone Connect is connected to a cordless phone base station, any
extension phones mated with that base station will also receive service.
Powering on the Device
Press the
button to power on the device. When the device is on, the power indicator will be
blue.

Note:
Press and hold the
button for 1 second to power off the device.
Activating the Device
If your device has not yet been activated, please follow the steps below:
1.
2.
Dial * 2 2 8 from a telephone that is connected to the Home Phone Connect to activate the
device.
You will hear a confirmation tone or message once programming is complete.
Understanding the Indicators
The following table describes your device’s status at any given time.
Icon
Indicator
Status
Voice mail
Blinking Blue
New Message
Blue
Full Charge
Blinking Blue
Partial Charge
Blinking Red
Low Charge
Both Blue
Strong
One Blue
Moderate
One Blinking Blue
Weak
Blue
The device is on
Battery
Signal Strength
Power
Making Calls
1.
2.
3.
Before making a call, make sure signal and signal strength indicators are lit up.
Place a call by entering the desired telephone number, including the area code, on your
telephone.
When your call is complete, hang up or return the phone to the receiver to ensure that you can
receive calls.
Call Forwarding
The device allows you to forward calls to another phone number, including your mobile phone or
office number. Your Home Phone Connect will not ring until you deactivate the service. Airtime
applies to forwarded calls even if you send the call to wire line telephones.
To Activate Call Forwarding:
1.
2.
3.
4.
Dial * 7 2.
Immediately enter the phone number where you want calls to be forwarded (e.g.
*72-212-123-4567).
You will hear a confirmation tone.
Hang up or return the phone receiver to its base.
To Deactivate Call Forwarding:
1.
2.
3.
Dial * 7 3.
You will hear a confirmation tone.
Hang up or return the phone receiver to its base.
Fax Machine Compatibility
Your Home Phone Connect does not support incoming or outgoing fax service.
Home Security Systems
Your Home Phone Connect may not be compatible with certain Home Security systems. Please
check with your security system provider to confirm the compatibility requirements of your Home
Security system.
911 Calls
Since the device is designed for an indoor environment, please be prepared to provide your
location inside the premises to public service personnel. The GPS chipset embedded in this device
will work best if the device is located near a window or other opening.

Note:
While the Home Phone Connect adapter has a backup battery, if the landline device
requires external power to operate, service (including the ability to make and receive 911
calls) will not be available during a power outage.
Please refer to the User Manual for more details.
96722016_02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement