Handicare puma 20 User manual
Puma 40, your new electric wheelchair, offers unparalleled driving comfort with its unique independent suspension system that absorbs shocks and vibrations. With two available speeds, 6 km/h and 10 km/h, you can choose the pace that suits your needs. It's suitable for both indoor and outdoor use, thanks to its two different types of tires. Safety features include a maximum safe slope of 10 degrees and a user weight limit of 160 kg. Experience freedom and mobility like never before with Puma 40.
Advertisement
Advertisement
USER MANUAL
PUMA 40
EN
9006403E
English
© 2011 Handicare
All rights reserved.
The information provided herein may not be reproduced and/or published in any form, by print, photoprint, microfi lm or any other means whatsoever (electronically or mechanically) without the prior written authorization of Handicare.
The information provided is based on general data concerning the construction known at the time of the publication of this manual. Handicare executes a policy of continuous improvement and reserves the right to changes and modifi cations.
The information provided is valid for the product in its standard version. Handicare can therefore not be held liable for any damage resulting from specifi cations of the product deviating from the standard confi guration. Illustrations contained in the manual may deviate from the confi guration of your product.
The information made available has been prepared with all possible diligence, but Handicare cannot be held liable for any errors contained in the information or the consequences thereof.
Handicare accepts no liability for loss resulting from work executed by third parties.
Names, trade names, trademarks etc. used by Handicare may not, as per the legislation concerning the protection of trade names, be considered as being available.
2011-01
4 |
1 Introduction
1.1 This user manual
1.2 Symbols used in this manual
2 Safety
2.1 Temperature
2.4 Markings on the wheelchair
3.2 Confi gurations
4.3 Centre of gravity setting
4.4 Controller height and depth
4.5 Control system programme
5 Use of the wheelchair
5.1 Checking the wheelchair before use
5.2 Getting in and out of the wheelchair (transfer)
5.3 Driving the wheelchair
5.4 Obstacles
5.6 Pushing the wheelchair
5.7 Transport of the wheelchair (without occupant)
5.8 The wheelchair as a passenger seat in a car
5.9 Fastening the seat belt
5.10 Storage after use
6 Maintenance of the wheelchair
6.2 Batteries
6.3 Tyres
6.4 Cleaning the wheelchair
6.5 Decommissioning the wheelchair
7 Troubleshooting
8.1 CE declaration and requirements
8.3 Electric wiring diagram
13
13
13
13
14
14
10
10
10
11
11
12
19
19
20
22
22
15
15
15
16
18
18
7
7
7
8
9
6
6
6
26
27
27
27
29
23
23
23
24
24
25
9 Warranty
9.1 Provisions of warranty
| 5
30
30
31
6 | Introduction
1 Introduction
Congratulations on choosing a Handicare wheelchair. Handicare’s high-quality mobility products are designed to enhance independence and make your everyday life easier.
1.1 This user manual
This user manual will help you to use and maintain your wheelchair safely. This entire user manual for this wheelchair consists of three booklets:
• The general wheelchair user manual (this booklet)
• The user manual for the seating system
• The user manual for the controller
When necessary this general user manual refers to other manuals as shown below:
Seating system: Refers to the user manual for the seating system.
Controller: Refers to the user manual for the controller.
Battery charger: Refers to the user manual for the battery charger.
Read this entire user manual (all of the booklets) carefully before using the product.
If one of the user manuals was not included with your wheelchair, please contact your dealer immediately.
In addition to this user manual, there is also a service manual for qualifi ed specialists.
CONTACT HANDICARE IF YOU HAVE A
VISUAL IMPAIRMENT.
1.2 Symbols used in this manual
Note!
Pointing out possible problems to the user.
Caution!
Advice for the user to prevent damage to the product.
Warning!
Warnings for the user to prevent personal in jury.
Not following these instructions may result in physical injury, damage to the product or damage to the environment!
Safety | 7
Warning!
Always follow the instructions given next to the warning symbols! Not following these instructions may result in physical injury, damage to the wheelchair or damage to the environment. Where possible, the warnings have been placed in the applicable paragraphs.
2.1 Temperature
Warning!
Avoid physical contact with the wheelchair’s motors. The motors are continuously in motion during use and can reach high temperatures.
After use, the motors will cool down slowly.
Physical contact may cause burns.
Ensure that the wheelchair is not exposed to direct sunlight for extended periods of time.
Certain parts of the wheelchair, such as the seat, the backrest and the armrests, can become hot if exposed to the sun for too long.
This may cause burns or skin irritation.
The standard version of your electric wheelchair has been tested for compliance with the applicable requirements regarding electromagnetic radiation (EMC requirements).
Note!
It cannot be excluded that electromagnetic radiation emanating from mobile telephones, medical apparatus and other sources, may have an infl uence on the wheelchair.
It cannot be excluded that the wheelchair will interfere with the electromagnetic fi elds of, for example, shop doors, burglar alarm systems and/or garage door openers.
In the unlikely event that such problems do occur, you are requested to notify your dealer immediately.
8 | Safety
Warning!
Contact with the moving parts of the wheelchair should be avoided. A wheelchair has moving and rotating parts. Contact with moving parts may result in serious physical injury or damage to the wheelchair.
Moving/rotating parts (fi gure 1)
1. Wheels (turning and pivoting)
2. Electrical tilt adjustment
3. Electrical high/low adjustment
4. Electrically reclining backrest
5. Electrically elevating legrests
Figure 1
Safety | 9
2.4 Markings on the wheelchair
Note!
Never remove or cover up the markings, symbols and instructions affi xed to the wheelchair. These safety features must remain present and clearly legible throughout the entire lifespan of the wheelchair.
Replace or repair any markings, symbols or instructions that have become illegible or damaged immediately.
Please contact your dealer for assistance.
Markings used on the wheelchair (fi gure 2):
1. Check manual before using
2. Freewheel switch in ‘Drive’ mode. Freewheel switch in ‘Push’ mode. Never set the freewheel switch to
‘Push’ mode while the wheelchair is on a slope.
3. Battery charging connection
4. Attachment point for the tie-down system for transportation in a vehicle.
5. Risk of breakage! Use caution when swinging the controller aside in order to avoid anything becoming trapped.
6. Risk of pinching. Keep hands and fi ngers clear of the moving parts when adjusting the height and/or when adjusting the tilt of the wheelchair.
7. Identifi cation plate
A. Model
B. Year of manufacture
C. Identifi cation number
D. Indoor or outdoor use
E. Maximum load in kg
1
2
3
4
5
6
7
Figure 2
101248-05_14
10 | General description
Comfort is of paramount importance to many people who make use of a wheelchair. And this is exactly what this electrical driven wheelchair offers: an unknown degree of driving comfort. A distinctive feature is the unique independent suspension system, which absorbs not only shocks, but also vibrations.
9
6
7
4
5
(fi gure 3 and 4)
1. Drive wheels
2. Castor wheels
3. Freewheel switch
4. Controller
5. Seat cushion
6. Backrest
7. Armrest
8. Legrest with foot support
9. Headrest
3.2 Confi gurations
Generally speaking, the wheelchair comprises a chassis with a seating system on top. This special chassis makes it possible for the wheelchair to be confi gured as front wheel drive (FWD, fi gure 3) or rear wheel-drive
(RWD, fi gure 4). The wheelchair is available in different speeds (6 km/h & 10 km/h).
In addition, the Puma 40 can be supplied with two different types of tyres (for indoor and outdoor use).
This will have an effect on certain specifi cations.
Warning!
It is not allowed to change the technical specifi cations.
Do not make any changes to the electrical circuit.
Modifi cations to the wheelchair or to any parts thereof are not permitted.
8
Figure 3
9
6
7
4
5
8
Figure 4
2
3
1
101248-05_23
1
3
2
101248-05_22
General description | 11
Caution!
Parts of the wheelchair that are intended, for servicing or repair, to be removed without the use of tools (e.g. electronics and battery covers) can have an adversery effect on the electrical functioning of the wheelchair if they are missing or not placed back in the right position.
Driving an electric wheelchair requires a user to have cognitive, physical and visual skills.
The user must be able to estimate and correct the results of actions taken when operating the wheelchair.
The wheelchair may not transport more than one person at a time. The maximum user weight is 160 kg unless otherwise indicated on the identifi cation plate. Additional weight, such as rucksacks, accessories or medical apparatus, must be added to the user’s weight to determine the maximum weight, which may not be exceeded.
The user must be familiar with the contents of the user manual before driving the wheelchair.
In addition, the user of the wheelchair must have been given thorough instruction in using the wheelchair by a qualifi ed specialist before he or she participates in traffi c. The fi rst sessions in the wheelchair should be held under the supervision of a trainer/advisor.
Warning!
The user of the wheelchair is responsible for complying with the applicable local safety regulations and guidelines.
Driving the wheelchair under the infl uence of medicines that can affect your ability to drive is not permitted.
Driving the wheelchair without suffi cient eyesight is not permitted.
No more than one person is to be seated in the wheelchair at a time.
Do not allow children to ride in the wheelchair unsupervised.
This wheelchair has been designed for both indoor and outdoor use (EN12184 (2009) class
B). When driving the wheelchair outdoors, drive only on paved roads, pavements, footpaths and bicycle paths. The speed must be adjusted to suit the environment.
When all of the adjustment options are set to standard position (see paragraph 3.5), a slope of ≤10˚ is deemed to be a normal user environment for an RWD model without there being any danger of instability. For an
FWD model this is ≤ 10˚. In the technical specifi cations, you will fi nd this under ‘maximum safe slope’.
Warning!
Drive carefully on roads which are slippery as a result of rain, ice or snow!
Always turn on lights in cases of limited visibility.
Exert extra care when driving at higher speeds.
Select a lower maximum speed when driving indoors, on pavements and in pedestrian areas.
Do not drive off of high obstacles.
Do not use the wheelchair if temperatures are below -10˚C or above +50˚C.
Do not attach any weights to the wheelchair without the approval of a qualifi ed specialist.
This may negatively affect the stability of the product.
Do not use the wheelchair for pushing and/or towing objects.
Do not use the legrests for opening doors.
Do not drive through puddles of water
(ISO7176-9-IPX4).
Note!
Prevent the wheelchair from coming into contact with sea water: sea water is caustic and may damage the wheelchair.
12 | General description
Prevent the wheelchair from coming into contact with sand: sand can permeate into the moving parts of the wheelchair, causing unnecessary fast wear of these parts.
The wheelchair can be supplied with the following electrical and/or mechanical adjustment options
(fi gure 5):
1. Electrical tilt adjustment
Standard position: not tilted
2. Electrical high/low adjustment
Standard position: lowest position
3. Electrically reclining backrest
Standard position: upright
4. Electrically or mechanically elevating legrests
Standard position: as vertical as possible
Warning!
Use of the electrical adjustment options may infl uence the stability of the wheelchair. Use the adjustment options only when the wheelchair is on a fl at surface.
Avoid contact with moving and/or rotating parts when making electrical adjustments. Contact with moving and/or rotating parts may result in serious physical injury or damage to the wheelchair.
Figure 5
The average wheelchair user does not exist. This is why Handicare wheelchairs can be adjusted according to the specifi c needs of the user.
In this, we make a distinction between wheelchair settings and wheelchair adjustment options. Settings are carried out only once and must be executed by qualifi ed specialists, unless explicitly stated otherwise.
Adjustment options can be carried out by the user.
These adjustment options do not require the use of tools.
The extensive settings with respect to the seating system allow for optimum support of the body
( Seating system). The following setting options are possible:
1. Seat depth and seat width
2. Backrest angle
3. Armrest height
4. Lower leg length
5. Angle of the footplate
Figure 6
Depending on the specifi c circumstances of the user of the wheelchair the seat height can be set. Every optional seat height lays within the 10˚ (17.6%) maximum safe slope of according to EN12184 (2009)
ClassB. Lowering the seat height has a positive infl uence on the (dynamic) stability.
Warning!
Increasing seat height has a negative effect on dynamic stability.
4.3 Centre of gravity setting
The wheelchair’s centre of gravity (fi gure 6) can be adjusted within the seating system ( Seating system).
Caution!
Changing the wheelchair’s centre of gravity may negatively infl uence the wheelchair’s driving characteristics and/or its dynamic stability.
Wheelchair settings | 13
101248-05_12
14 | Wheelchair settings
In case of doubt, contact the technical support department at Handicare.
4.4 Controller height and depth
( Seating system)
4.5 Control system programme
This wheelchair is equipped with a control system that can be programmed by adjusting settings within the system. This is a specialized job that needs training and can only be adjusted with professional software. It’s not possible and allowed for end users to adjust these settings.
Warning!
The incorrect setting of the parameters for the control system may result in very dangerous situations.
Settings must be made by qualifi ed specialists.
5 Use of the wheelchair
5.1 Checking the wheelchair before use
Before driving check that:
1. The tyres are suffi ciently infl ated (see § 6.3).
2. The batteries are suffi ciently charged. The green lights on the battery indicator must be on.
( Controller)
3. The lights and the indicator lights are working properly. ( Controller)
4. The freewheel switch has been set to ‘drive’
(see § 5.6).
Note!
Before use, always check to see whether clothing or accessories could come into contact with wheels or other moving and/or rotating parts in which they could become entangled.
The capacity of batteries is reduced in winter. During a period of light frost, the capacity is roughly 75% of the normal capacity. At temperatures below -5˚C this will be roughly 50%. This will reduce the wheelchair’s range.
Figure 7
5.2 Getting in and out of the wheelchair
(transfer)
( Seating system)
Before a transfer is made, ensure that:
Warning!
The controller has been switched off.
The freewheel switch has been switched to ‘drive’ (see
§ 5.6)
Warning!
Do not stand on the footrests. Putting your full weight on the footrests may lead to wheelchair damage and to hazardous situations, including the wheelchair tipping up.
Forwards transfer (fi gure 7)
Sedeo Original standard legrest
1. Fold up the foot supports
2. Swing the calf plates to the side (if applicable)
3. If possible, swing the legrests to the side
4. Seat yourself in the chair
Use of the wheelchair | 15
16 | Use of the wheelchair
Flipping up the central legrest footplate (fi gure 8)
1. Flip up (A).
Sideways transfer
Removing the armrest assembly (fi gure 9)
1. Tip (A) downwards.
2. Remove (B).
Folding back the armrest (fi gure 10)
1. Press (A).
2. Fold (B) to the rear.
Caution!
Remove the tray before folding back the armrest.
A
Figure 8
5.3 Driving the wheelchair
Note!
Bear in mind that other road users may not always notice you.
Observe the traffi c regulations in force.
Avoid out-of-the-way routes so that help can be found quickly when needed.
Adjust your driving style and speed to the circumstances.
Electric wheelchairs are driven by means of a controller.
There is a separate user manual for the controller and this was included with this wheelchair ( Controller).
1. Switch on the controller.
2. Set the maximum speed limit.
3. Move the joystick in the direction in which you would like to go.
4. Moving the joystick even further forwards will cause the wheelchair to drive faster.
B
Figure 9
B
A
2
2
1
3EDEO
3EDEO
Figure 10
A
1
3EDEO
Use of the wheelchair | 17
Curves
Note!
Never take curves at full speed. Decrease your speed before taking a curve.
Use the indicators when changing direction.
Braking/Emergency stop
To brake, move the joystick to the neutral position or release completely. The wheelchair will then brake automatically. An emergency stop can also be made by releasing the joystick.
Stopping distance:
• 6 km/h: 1 meter
• 10 km/h: 2 meter
Warning!
When driving avoid the following:
Do not push the on/off button.
Do not change to driving in the opposite direction suddenly.
In such cases, the wheelchair will come to an abrupt standstill with a sudden jolt. Not only is this uncomfortable, it could lead to the wheelchair tipping over if on a slope.
Driving on a slope
When all of the adjustment options are set to the standard position (see chapter 3.5), a gradient of ≤10˚ (17.6%) is deemed to be a normal user environment for an RWD wheelchair without there being any danger of instability. For an FWD model this is ≤ 10˚
(17.6%).This information can be found in the technical specifi cations under ‘maximum safe slope’.
Slopes steeper than the normal user environment
Driving on slopes with a gradient greater than the maximum safety limit may lead to safety risks with respect to stability. This requires great care and complete control on the part of the user. Always drive carefully and never take unnecessary risks! Follow the instructions given by the warnings!
The stability and performance of a wheelchair depend on a number of variables. Wheelchairs are adapted to the needs of individual users.
This is why variables will differ from wheelchair to wheelchair. You should therefore ask your dealer to inform you about how to use the wheelchair and whether the specifi c settings and adjustments for your own situation can infl uence the driving characteristics of the wheelchair.
Warning!
When driving on a slope, always drive carefully and with the utmost concentration.
Avoid sudden, jerky movements.
Avoid making emergency stops on a slope.
Avoid changing direction on a slope whenever possible.
Do not turn on a slope.
Only drive up a slope with all the adjustment options set to the neutral position.
Never drive in reverse on a slope.
Do not drive on slopes with loose gravel or a sandy surface, as one of the driving wheels could slip/spin.
Do not drive on slopes for extended periods of time in order to prevent the motor from overheating.
When driving down a slope forwards in an FWD wheelchair, use an anti-tip mechanism.
If you notice a signifi cant decrease in speed when driving up a slope, take a route which is less steep.
Prevent the wheelchair from gaining too much speed when driving downhill.
18 | Use of the wheelchair
5.4 Obstacles
Driving up a kerb
1. Choose the place where the kerb is at its lowest.
2. Drive straight up to the kerb at a right angle to it
(20 cm in front of the kerb).
3. Move the joystick forwards. Drive up the kerb without changing direction.
4. Maintain speed until all of the wheels are on the pavement. If mounting the pavement is not possible, fi nd a place where the kerb is lower.
Driving down a kerb
1. Choose the place where the kerb is at its lowest.
2. Drive straight down the kerb with your front wheels at a right angle to it.
3. Move the joystick slowly forwards. Drive down the kerb carefully and as slowly as possible without changing direction.
Warning!
Never drive down steps or off of obstacles higher than
60 mm in a wheelchair.
Figure 11
The wheelchair can be supplied with the following adjustment options which can be made by the user without the use of tools:
Mechanical adjustment options (
Seating system)
1. Manually elevating legrests
2. Swing-away joystick holder
3. Headrest
Electrical adjustment options (
Controller)
(fi gure 11)
1. Electrical tilt adjustment
2. Electrical high/low adjustment
3. Electrically reclining backrest
4. Electrically elevating legrests
Use of the wheelchair | 19
5.6 Pushing the wheelchair
The wheelchair can also be moved by pushing. In order to do so, the motors must be disengaged using a freewheel switch. This feature was developed for the attendants of wheelchair users.
The freewheel switch has two positions:
1. The ‘Drive’ position (fi gure 12A).
2. The ‘Push’ position (fi gure 12B).
Warning!
The freewheel switch should only be operated by the attendant and never by the user.
Never set the switch to ‘push’ on a slope! When the freewheel switch is set to ‘push’, the automatic parking brake is deactivated. This makes it possible for the wheelchair to roll down the slope.
The automatic parking brake only works if the switch is set to the ‘drive’ position.
When the chair is no longer being pushed, the freewheel switch should be set to ‘drive’ immediately.
Figure 12
B
5.7 Transport of the wheelchair (without occupant)
Parts of the wheelchair that can easily be detached should be removed when transporting the wheelchair (fi gure 13) ( Seating system).
1. Remove the seat
2. Remove the legrests
3. Remove the armrests
4. Fold down the backrest
Store these parts securely. Use suitable ramps for wheeling the chair in and out of the vehicle. Once the wheelchair is in the vehicle, it must be secured with an
ISO 10542 approved tie-down system that is suited to the weight of that particular wheelchair including any options (Chapter 8).
Figure 13
A
Pag.
10 nr.2
101248-05_13
101248-05_28
20 | Use of the wheelchair
5.8 The wheelchair as a passenger seat in a car
Note!
This wheelchair is crashtested according to ISO 7176-
19 (2008) with a maximum passenger weight of 136 kg.
Wheelchairs are not primarily designed to be used as car seats and cannot offer the same degree of safety offered by standard car seats, no matter how securely they have been tied down in the vehicle concerned.
Due attention should be paid to the following points when a transfer from the wheelchair to a standard car seat is not possible.
The wheelchair can be used as a passenger seat in a car or bus by using a 4-point integrated transport tie-down system that has been approved to ISO 10542. standards. Make sure that this restraint system is suitable to the total weigth of the wheelchair. The weight of a wheelchair depends on it’s confi guration. The specifi cations (chapter 8) give an overview of several options and their share in the total weight. Always weigh the total chair to make sure that the right restraint system is used.
The system requires tie-down rails to be mounted in the car. The chair must then always be strapped to the four tie-down points (fi gures 14).
Warning!
Transfer to a regular car seat if possible
Use for the fi xation of the occupant a 3 point occupant restraint system. Always follow the instructions of this system.
Always ask the transporter for confi rmation that the vehicle is suitably designed, insured and equipped for transporting a person in a wheelchair.
The wheelchair must be positioned in the vehicle so that it is facing forwards.
The wheelchair has been dynamically tested in a forwardfacing orientation with the test dummy restrained by both pelvic and shoulder belts (e.g. a shoulder belt as part of a three-point belt restraint).
Figure 14
101248-05_27
Use of the wheelchair | 21
Both pelvic- and shoulder-belt restraints should be used to reduce the possibility of head and chest impacts with vehicle components.
Wheelchair mounted trays should:
1. be removed and secured seperately in the vehicle
2. be secured to the wheelchair but positioned away from the occupant with energyabsorbing padding placed between the tray and the occupant.
Set the wheelchair in the standard position
(chapter 3.5) and use the headrest if the wheelchair is fi tted with one.
The chair must always be switched off when being transported.
Support and positioning equipment must not be used as seat belts if not labelled as being in accordance with the requirements of ISO 7176/19
Gel-fi lled batteries only should be used.
No changes may be made to the tie-down points/car restraining points on the wheelchair, or to the design of the frame without consulting the manufacturer.
The wheelchair should be inspected by a Handicare’s representative before reuse following involvement in any type of vehicle collision.
Care should be taken when applying the occupant restraint to position the seatbelt buckle so that the release button will not be contacted by wheelchair components during crash.
The wheelchair has been tested in accordance with ISO 7176-19 (2008) with Q-straint Q195 and Q-straint QE5-6343 (>75 kg)
22 | Use of the wheelchair
5.9 Fastening the seat belt
Warning!
Use the three-point seat belt in order to reduce the risk of head and chest injuries in the event of the wheelchair colliding with parts of the car.
The wheelchair should always be inspected by a representative of the manufacturer following any kind of collision.
Use the seat belt as follows:
• Position the belt across the hips as tightly as possible at an angle between 30° and 75°. The other part of the belt is positioned to sit across the chest and shoulder (fi gure 15).
• The seat belt should fi t as tightly as possible and must not be twisted.
• Ensure that the seat belt is not obstructed from having contact with the body by wheelchair parts, such as armrests or wheels (fi gure 16).
Trays fi tted to the wheelchair which do not comply with safety requirements must be:
• Removed and secured separately in the vehicle.
• Secured to the wheelchair, with shock-absorbing padding placed between the tray and the user.
In order to prevent injury in the event of a collision, secure wheelchair accessories to the wheelchair or remove them from the chair and secure them in the vehicle.
5.10 Storage after use
When the wheelchair is not in use, it must be stored in a dry place where it will not be exposed to weather conditions.
Note!
Do not place the wheelchair in direct sunlight. Under such circumstances parts of the wheelchair can become so hot that they can cause burns. During storage, the ambient temperature should not be lower than -20˚C or higher than +65˚C.
Figure 15
Figure 16
101248-05_17a
101248-05_17a
Maintenance of the wheelchair | 23
6 Maintenance of the wheelchair
The wheelchair’s lifespan is dependent on it being well maintained.
For information concerning specifi c settings, maintenance or repair work, please contact your dealer. Always be sure to mention the model, year of manufacture and identifi cation number provided on the identifi cation plate of the wheelchair when contacting your dealer.
Note!
The wheelchair should be serviced by your dealer once a year or, in the case of intensive use, every six months.
Daily
Weekly
Task
Charge the batteries after each use
Check the tyre pressure and infl ate the tyres if necessary
Chap.
6.2
6.3
Monthly Clean the wheelchair 6.4
Annually
Have wheelchair serviced by dealer
-
6.2 Batteries
The wheelchair uses two 12V ‘dry’ gel batteries in series. These batteries are fully sealed and require no maintenance.
Note!
Do not use ‘wet’ batteries.
Take into account the fact that the wheelchair’s range is reduced at low temperatures. During a period of light frost, the capacity is roughly 75% of the normal capacity. At temperatures below
-5˚C this will be roughly 50%.
Charging the batteries (
Battery charger )
Consult the user manual for the battery charger to determine whether it is suitable for the batteries in use. See chapter 8.
• Switch off the wheelchair’s controller.
• Plug the battery charger’s charging plug into the charging connector on the controller.
• Activate the battery charger. Consult the user manual for the battery charger.
Charge the batteries if the wheelchair is not being used for an extended period of time. The batteries should be charged every night under normal use. The battery charger’s display will indicate when the batteries are fully charged.
Depending on how depleted the batteries are, it may take up to 12 hours to fully charge the batteries again.
Maintaining the batteries
Note!
Ensure that the batteries are always fully charged. Not using the batteries for an extended period of time can damage them.
Do not use the wheelchair if the batteries are almost depleted and never completely deplete the batteries. This can seriously damage the batteries and you may run the risk of coming to an unintended standstill.
Replacing the batteries
If the capacity of the batteries is continually decreasing so that the wheelchair can only be used for short trips, then this means that the batteries are reaching the end of their lifespan.
The batteries will then need to be replaced.
Please contact your dealer for assistance.
Warning!
Batteries contain acids. Damaged batteries are a serious health hazard. Follow the instructions on the batteries at all times.
24 | Maintenance of the wheelchair
6.3 Tyres
To ensure that your wheelchair functions properly, it essential that the tyres are kept at the correct pressure. The correct pressure is indicated on the side of the tyre.
Tyre pressure
Puma 40
Castor wheel 9”
Castor wheel 10”
Drive wheel 13”
Drive wheel 14”
3.5 bar max.
3.5 bar max.
2.8 bar max.
2.1 bar max.
Tyres that are too soft will have a negative effect on the wheelchair’s performance. Moving the wheelchair will require more energy, making more demands on the batteries. Furthermore, wear on the tyres when driving with soft tyres is unnecessarily high.
Note!
Never exceed the maximum tyre pressure
6.4 Cleaning the wheelchair
Please consult the user manual for the seating system for information about cleaning the seating system ( Seating system).
Caution!
Ensure that the controller is switched off while cleaning. If the joystick is accidently touched, the wheelchair can start to move or the electrical options can be operated accidentally.
Take care with water in view of the electronic system
Removing dry dirt
First, wipe the dirty parts clean using a wet sponge. Preferably use clean water or a mild soap solution. Wipe the parts dry using a soft dry cloth.
Note!
Never use abrasive or aggressive cleaning agents. These can scratch the wheelchair.
Do not use organic solvents such as thinner, benzine or white spirit.
Drive wheel tyre repair
Note!
Tyres should only be replaced by a qualifi ed specialist. For an extensive description of tyre repairs, please refer to the service manual available to qualifi ed specialists.
Before tyres are repaired they must fi rst be fully defl ated.
wheelchair
Under normal use and with prescribed maintenance, the wheelchair’s expected lifespan is approximately seven years.
The environment
If your wheelchair has become superfl uous or needs to be replaced, it can usually be taken back by your dealer in consultation. If this is not possible, please ask your local authority about the possibilities for recycling or environmentally friendly disposal of the materials.
Various different plastics and metals were used in the manufacture of the wheelchair.
Furthermore, the wheelchair contains electronic components that should be disposed of as electronic waste. The batteries should be disposed of as chemical waste.
A disposal fee is not applied to wheelchairs.
Maintenance of the wheelchair | 25
26 | Troubleshooting
7 Troubleshooting
If the wheelchair is not working as it should, check the following points.
• Check whether the batteries are charged.
• Turn the wheelchair off and then back on again.
• Check whether the battery plugs are all securely in place.
• Check whether the freewheel switch is in the
DRIVE position.
• Check the position of the speed regulator.
If the problem has not been resolved:
• Consult the troubleshooting section of the manual for the controller ( Controller).
If, after taking all of the above steps, the problem still persists, contact your dealer.
Technical specifi cations | 27
8.1 CE declaration and requirements
This product complies with the COUNCIL DIRECTIVE 93/42/EEC of 14 June 1993 concerning medical devices. The product also meets the following requirements and standards. This has been verifi ed by independent test organizations.
Standard Defi nition/description
Test dummy weight
EU guideline
93/42 EEC
Requirements as stated in Appendix 1 apply
NEN-EN 12182
The EN 12182 requirements as stated in NEN-EN 12184 (2009):
Technical aids for disabled persons - General requirements and test methods October 1999
NEN-EN 12184
(2009)
Class B
Electrically powered wheelchairs, scooters and their chargers -
Requirements and test methods October 2009
ISO 7176-8
Requirements and test methods for impact, static and fatigue strengths July 1998
ISO 7176-9
ISO 7176-14
ISO 7176-19
(2008)
Climatic tests for electric wheelchairs IPX4
Requirements and test methods for power and control systems for electrically powered wheelchairs 1997
The Puma 40 meets the crash test requirements as described in
ISO 7176-19 (2008) n/a
160 kg
160 kg n/a n/a n/a
102 kg
Batteries
Maximum battery dimensions
Battery capacity
Maximum permissible charging voltage
Maximum charging current
Connector type
Insulation
Max.
260 x 172 x 210
(10.25 x 6.75 x 8.25)
40 / 60 / 74 GEL
24
12
Controller
Class 2 double insulated
Unit mm inch
Ah
V
A (rms)
28 | Technical specifi cations
Model
Class
Description
Total length including legrests
Total width 13” drive wheels
Total width 14” drive wheels
Total weight without batteries:
Batteries 40 Ah (C20) (set of two)
Batteries 60 Ah (C20) (set of two)
Batteries 74 Ah (C20) (set of two)
Electrical high/low adjustment
Electrical tilt adjustment
Electrically reclining backrest
Electrically elevating legrests
Puncture-proof drive wheels (set of two)
Transport weight of the heaviest part
Maximum safe slope
Static stability
Downwards
Upwards
Sidewards
Reversing distance
Turning radius (ISO 7176-5)
Distance range* 74 Ah (C20) approx. (ISO 7176-4)
6 km/h
10 km/h
Climbing capacity for obstacles (outdoor)
Maximum speed forwards
Seat angle adjustment
Effective seat depth
Effective seat width
Seat height (excl. cushion)**
Seat height (incl. cushion)**
Backrest angle
Backrest height
Lower leg length
Unit mm (inch) mm (inch) mm (inch) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.)
° (%)
°
°
° mm (inch) mm (inch) km (mi.) km (mi.) mm (inch) km/h
° mm (inch) mm (inch) mm (inch) mm (inch)
° mm (inch) mm (inch)
Puma 40 Sedeo Pro
FWD
1190 (46.9) 1115 (43.9)
610 (24)
655 (25.8)
97,6 (15.4)
+ 28,4 (4.5)
+ 34,6 (5.5)
+ 45,8 (7.2)
+ 18,8 (3)
+ 9,8 (1.5)
+ 1,5 (3.3)
+ 4 (8.8)
+ 8,4 (1.3)
97,6 (15.4)
10 (17.6)
1200 (47.2)
600 (23.6)
B
15
15
15
RWD
1700 (66.9)
850 (33.5)
60 (2.4)
49,9 (31)
43,7 (27.2)
80 (3.1)
6 / 10
0 - 6
440 - 600 (17.3 - 23.6)
420 - 540 (16.5 - 21.3)
405 / 430 / 455 / 480 / 505
(15.9 / 16.9 / 17.9 / 18.9 / 19.9)
475 / 500 / 525 / 550 / 575
(18.7 / 19.7 / 20.7 / 21.7 / 22.6)
89 - 118
500 - 640 (19.7 - 25.2)
360 - 530 (14.2 - 20.9)
* The following aspects have a negative effect on the distance range: obstacles, rugged terrain, driving on slopes, exposure to temperatures below freezing point and frequent use of electronic adjustment options.
** Seat height incl. load, 0° seat angle and 14” drive wheels
Technical specifi cations | 29
8.3 Electric wiring diagram
The electric wiring diagram varies according to the type of controller used (
Controller).
30 | Warranty
9 Warranty
9.1 Provisions of warranty
In the warranty and liability provisions the following terms are defi ned as follows:
• Product : The manual or electric wheelchair or scooter manufactured and supplied by
Handicare.
• Customer : The person who directly obtains a product from Handicare.
• Dealer
: The person who supplies a product obtained from Handicare to third parties.
• User : The person who uses a product manufactured by Handicare.
Irrespective of what has been determined concerning warranty conditions in the general terms and conditions applicable to the product, the following shall in any case apply with regard to the warranty:
1. Except insofar as described otherwise in the provisions below, Handicare guarantees the product for its suitability for the purpose for which the product is intended - all of these points as described in this manual - and for the quality of the material of which the product is made and the manner in which the product is manufactured.
2. Repairs or replacement of parts of the product that may be necessary as a result of faults that are based on qualitatively faulty material or manufacturing errors shall be carried out free of charge, as long as such faults occurred within one (1) year of the date of delivery of the product to the Customer. The parts to be replaced must be shipped post-paid to Handicare.
Disassembly or assembly of these parts shall be at the expense of the Customer.
Therefore the following cases shall not be eligible for free repair or replacement as referred to in the previous sentence:
A. Repair or replacement that is necessary in connection with faults that arise after one (1) year from the date of delivery of the product to the Customer;
B. Repair or replacement that is required in connection with faults due to improper or careless use of the product or that are based on the product being used for another purpose than the one for which it is intended, in which regard it shall apply that if the Customer is a Dealer, this
Dealer shall indemnify Handicare against possible claims from Users or other third parties for faults based on an incorrect or careless use of the product;
C. Parts that are subject to wear, and the need for repair or replacement of the parts is the actual consequence of normal wear.
3. Irrespective of that stipulated under 2, as far as an electric product is concerned it shall apply that, with regard to the battery that forms part of the product, warranty is only given in case of faults or non-functioning of the battery that are demonstrably the direct consequence of material or manufacturing errors. A fault or non-functioning of the battery as a result of normal wear is not covered by the warranty as referred to in these warranty provisions. Similarly not covered by the warranty are faults or non-functioning that are the consequence of improper or unprofessional use of the product or the battery that is part of the product, including the incorrect charging of the battery and the failure to carry out timely and proper maintenance, in which context it shall also apply that if the
Customer is a Dealer, this Dealer shall indemnify Handicare against possible claims from Users or other third parties that are based on the above-mentioned improper or unprofessional use of the product or the battery that is part of the product.
4. The warranty conditions as stated in the above provisions shall in any case become null and void if:
A. Handicare’s guidelines for the maintenance of the product have not, or have insuffi ciently, been followed;
B. A necessary repair or replacement of parts is based on neglect, damage or abuse of the product or a use of the product for another purpose than the one for which it was intended;
C. Parts of the product have been replaced by parts of another origin than those which Handicare uses and/or parts of the product have been replaced without the
Warranty | 31 permission of Handicare.
5. The warranties as stated in provisions
1 to 3 also become null and void in the case of re-use by a new user within the warranty period and when such re-use necessitates adaptations to the product and those adaptations were not carried out on the instructions of and/or at the order of
Handicare.
6. To retain rights under the above delineated warranties, the Customer must, in the case of damage or other calamities, contact
Handicare as quickly as possible and provide Handicare with as much information as possible. The possibility of taking recourse to the above-mentioned warranty conditions shall in any case become null and void for the Customer after 20 workdays following the date of the claim incident or the calamity forming the basis for recourse to the guarantee.
7. The replacement of a part or the repair or the reconditioning of the product within the period a warranty period shall not extend the warranty period.
8. Handicare gives no warranty on repair to or reconditioning of the product carried out other than under order of and/or on the instructions of Handicare. If repairs and/ or reconditioning are carried out by or on behalf of a Customer, the Customer shall indemnify Handicare with respect to claims made by third parties which, in the broadest sense of the word, result from such repairs or reconditioning.
Irrespective of what is determined regarding liability in the general terms and conditions applicable to the product, the following shall in any case apply with regard to liability:
1. Taking into consideration the following provisions, Handicare shall only accept liability for loss due to death or physical injury that is the result of a defect in the product for which Handicare is responsible and for damage to another object that is the private property of the user of the product, as long as said loss is the direct result of a fault in the product.
2. Handicare accepts no other or further liability than delineated under 1. In particular Handicare accepts no liability for consequential damage, in any form whatsoever.
Dealer:
Serial number:
Advertisement
