MK Diamond Products MK-660 SERIES Owner`s manual

MK Diamond Products MK-660 SERIES Owner`s manual
www.mkdiamond.com
Revision 104
MK-660 tile saw
OWNER'S MANUAL
PARTS LIST &
OPERATING INSTRUCTIONS
09.2014
Manual Part# 153461
Caution: Read all safety and operating instructions
before using this equipment. This parts list MUST
accompany the equipment at all times.
INTRODUCTION
Congratulations on your purchase of a MK-660 Saw. We are certain that you will be pleased
with your purchase. MK Diamond takes pride in producing the finest construction power tools
and diamond blades in the industry.
Operated correctly, your MK-660 Saw should provide you with years of service. In order to help
you, we have included this manual. This owners manual contains information necessary to
operate and maintain your MK-660 Saw safely and correctly. Please take the time to familiarize
yourself with the MK-660 Saw by reading and reviewing this manual.
Read and follow all safety, operating and maintenance instructions.
If you should have questions concerning your MK-660 Saw, please feel free to call our friendly
customer service department at: 800 421-5830
Regards,
MK Diamond
NOTE THIS INFORMATION FOR FUTURE USE:
MODEL NUMBER:
SERIAL NUMBER:
PURCHASE PLACE:
PURCHASE DATE:
NOTE: For your (1) one year warranty to be effective, complete the warranty card
(including the Serial Number) and mail it in as soon as possible.
2
TABLE OF CONTENTS
SAFETY
Rules for Safe Operation
California Proposition 65 Message
Electrical Requirements
Safety Label Locations
Product Specifications
4-7
8
9-12
13
14
UNPACKING, TRANSPORT and ASSEMBLY
Unpacking15
Contents15
Transport16
Stand16
STARTUP, ADJUSTMENT, OPERATION and SHUTDOWN
Cutting Head Installation
17
Diamond Blade Installation 17-18
Adjustable Cutting Guide Installation
18
Splash Guard Installation
19
Water Pump Installation
19
Pre-Start Inspection
19-20
Connecting the Water Pump
21
Water Pump Setup for Operation 21
Recirculation21
Setup for Operation
22
Portable Generator
22
Operation (Cutting Straight edges, Diagonal Cutting, 45° Miter Cutting, Off-Angle Cutting)23-26
Cleanup27-28
MAINTENANCE AND TROUBLESHOOTING
Maintenance28-31
Flow adjustment
31
Blade Dressing
32
Diamond Blade Change-Out
33
Troubleshooting34-36
EXPLODED VIEW AND PARTS LIST
Exploded View & Parts List
38-40
ACCESSORIES ORDERING and RETURN INSTRUCTIONS
Accessories41
Ordering Information
42
Return Material Policy
42
Packaging Instructions
42
Authorized Service Centers
42
Contact & Warranty
43
3
MK-660 Tile Saw
SAFETY
Read and follow all safety, operating and maintenance instructions. Failure to read and follow
these instructions could result in injury or death to you or others. Failure to read and follow these
instructions could also result in damage and/or reduced equipment life. Safety warnings and
guidelines do not by themselves eliminate danger. They are not substitutes for proper accident
prevention procedures and good judgement.
))
SAFETY MESSAGES
ON
)
)
A safety message alerts you to potential hazards that could hurt you or others. Each safety message is
preceded by a safety alert symbol (
) and one of three words: DANGER, WARNING, or CAUTION.
((
((
ON
))
ON
((
DANGER
You WILL be KILLED or SERIOUSLY INJURED if you do not follow directions.
))
ON
((
WARNING You CAN be KILLED or SERIOUSLY INJURED if you do not follow directions.
CAUTION
You CAN be INJURED if you do not follow directions. It may also be used to
alert against unsafe practices.
DAMAGE PREVENTION AND INFORMATION MESSAGES
A Damage Prevention Message is to inform the user of important information and/or instructions that
could lead to equipment or other property damage if not followed. Information Messages convey
information that pertains to the equipment being used. Each message will be preceded by the word
NOTE, as in the example below.
NOTE: Equipment and/or property damage may result if these instructions are not followed.
general safety precautions and hazard symbols
In order to prevent injury, the following safety precautions and symbols should be followed at all times!
Safety Precautions
ALWAYS read this Owner’s Manual before operating the machine. DO NOT operate or
service this equipment before reading this entire manual. Read and understand all warnings, instructions and controls on the machine. Know how to stop the equipment quickly in
case of emergency. It is the operators responsibility to use this machine under safe working conditions and conform with federal, state and local codes or regulations pertaining to
safety, air, pollution, noise etc...
ALWAYS keep the Blade and Belt Guards in place. Do Not operate this machine with any
guard or safety device removed. A Guard, or any damaged part should be repaired or
replaced immediately.
NEVER operate this equipment without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job. Non-slip
foot wear is recommended.
))
((
ON
4
MK-660 Tile Saw
SAFETY
PERSONAL PROTECTIVE EQUIPMENT
always wear approved respiratory, head, ear and eye protection
when operating this machine.
ON
))
((
((
((
ON
((
ON STARTS!
ACCIDENTAL
))
))
Before starting the engine/motor, be sure the ON/OFF switch is in the OFF position to prevent accidental starting. Place the ON/OFF switch in the OFF position before performing any
service operation. ALWAYS place the power ON/OFF switch in the OFF position when the
machine is not in use.
))
ROTATING PARTS
Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the motor with covers, shrouds, or guards, removed.
HOT PARTS!
Engine components can become extremely hot from operation. To prevent severe burns,
do not touch these areas while the engine is running, or immediately after it is turned off.
Never operate the engine with heat shields removed.
))
((
ON
OVER SPEED
NEVER tamper with the governor components or settings to increase the maximum speed.
Severe personal injury and damage to the engine or equipment can result if operated at
speeds above maximum.
ELECTRICAL SHOCK
NEVER touch electrical wires or components while the engine is running. Exposed, frayed or
worn electrical wiring and plugs can be sources of electrical shock which could cause severe
injury or burns. Do not touch the plug with wet hands.
))
((
ALWAYS avoid inhalation of and skin contact with silica dust and/or mist. Provide proper
dust removal. Use dust-collection system when applicable.
NEVER operate the machine in an explosive atmosphere or near combustible materials.
))
Sparks
from the cutting-action of this machine can ignite flammable materials, liquids, gases
or dust.
((
ON
))
ON
((
This equipment should not be operated by persons under 18 years of age.
KEEP CHILDREN AWAY
All))visitors and children should be kept a safe distance from work area. Maintain a safe
operating distance to other personnel.
((
ON
MAKE
THE WORKSHOP KID PROOF
))
Make the workshops kid proof by using padlocks, master switches or by removing starter keys.
((
ON
DO NOT FORCE THE TOOL
A power tool will do a job better and safer operating at the rate for which it was designed.
DO NOT force a tool or an attachment to do a job that it was not designed to do.
5
SAFETY
((
MK-660
Tile Saw
ON
))
((
ON
USE PROPER APPAREL
DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may
be ))caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
SECURE WORK
Clamps
or a vise should be used to hold work whenever practical. Keeping your hands free
))
to operate a power tool is safer.
((
ON
DO)) NOT OVERREACH
Keep proper footing and balance at all times by not overreaching.
((
ON
((
ON
DISCONNECT TOOLS
Power
tools should always be disconnected before servicing, adjusting or when changing
))
accessories, such as blades, bits, cutters, and the like.
((
ON
MAINTAIN TOOLS WITH CARE
Keep tools clean and maintained for the best and safest performance. Always follow
maintenance instructions and examine the machine before use. If any abnormal vibrations
))
or noises
occurs, turn off machine immediately and have the problem corrected before
further use.
REMOVE ADJUSTING KEYS AND WRENCHES
Form
)) a habit of checking to see that keys and adjusting wrenches are removed from
the power tool before it is turned on.
((
ON
KEEP WORK AREA CLEAN
Cluttered
work areas and benches invite accidents. Keep area around machine clear of
))
obstructions which could cause persons to fall.
((
ON
((
ON
DO NOT USE IN DANGEROUS PLACES
DO NOT operate equipment in dangerous or hazardous environments. DO NOT use power
tools
)) in damp or wet locations nor expose them to rain. Always keep the work area well
lighted.
((
ON
USE RECOMMENDED ACCESSORIES
Consult the owner’s manual for recommended accessories. Using improper accessories
may) increase the risk of personal or by-stander injury. Unauthorized equipment
)
modifications will void all warranties. Manufacturer does not assume responsibility for any
accident due to equipment modifications.
))
ON
((
Always ensure that the machine is on level ground before using.
NEVER STAND ON THE TOOL
Serious
injury could occur if a power tool is tipped, or if a cutting tool is unintentionally
))
contacted.
((
ON
TRANSPORT
When loading or unloading the machine, use caution. Remove the blade prior to hoisting,
loading and transporting the machine.
6
SAFETY
((
MK-660
Tile Saw
ON
))
((
ON
CHECK FOR DAMAGED PARTS
Before using a power tool, check for damaged parts. A guard or any other part that is
damaged should be carefully checked to determine if it would operate properly and
perform its intended function. Always check moving parts for proper alignment or binding.
Check for broken parts and mountings and all other conditions that may affect the
))
operation
of the power tool. A guard, or any damaged part, should be properly repaired or
replaced. Always check the machine for loose bolts before starting.
((
ON
DIRECTION OF ROTATION
A blade or cutter should always be installed so that rotation is in the direction of the
arrow
imprinted on the side of the blade or cutter. It should correspond with the rotational
))
direction of the motor. Always feed work into a blade against the direction of rotation.
((
ON
NEVER LEAVE A TOOL UNATTENDED
TURN
POWER OFF - Do not leave a tool until it comes to a complete stop. Always
))
turn a power tool OFF when leaving the work area, or, when a cut is finished.
((
ON
NEVER disconnect any "emergency or safety devices". These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm, or
even death! Disconnection of any of these devices will void all warranties. Unauthorized
equipment
modifications will void all warranties. Manufacturer does not assume
))
responsibility for any accident due to equipment modifications.
))
ON
((
NEVER use this machine with any cutter designed for woodworking.
))
ON
((
NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.
))
NEVER operate this equipment under the influence of drugs or alcohol.
((
ON
On belt driven equipment, overtensioning of belts will result in premature crank and/or bearing
failure.
))
((
ON
Whenever necessary, replace nameplate, operation and safety decals when they become
difficult
to read.
))
((
ON
Always store equipment properly when it is not being used. Equipment should be stored in
))
a clean, dry location out of the reach of children
((
ON
Do not lend or rent this equipment without including the Owner's Manual and the Engine/
))
Motor
Manufacturer's Manual.
((
ON
Check the chemical properties of the material to be cut/grinded and follow all EPA/OSHA
Regulations.
7
MK-660 Tile Saw
SAFETY
SILICA DUST WARNING
Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition
may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz,
brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of
airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance
known to cause cancer. When cutting such materials, always follow respiratory precautions.
Use appropriate NIOSH-approved respiratory protection where dust hazard may occur. Paper masks
or surgical masks without a NIOSH approval number are not recommended because they do little to
protect the worker. For more information about respirator programs, including what respirators have
received NIOSH approval as safe and effective, please visit the NIOSH website at:
http://www.cdc.gov/niosh/topics/respirators
Observe OSHA regulations for respirator use (29 C.F.R.§1910.134).
Visit http://www.osha.gov for more information.
CALIFORNIA PROPOSITION 65 MESSAGE
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead, from lead-based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium, from chemically treated lumber
For further information, consult the following sources:
http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html
Your risk from these exposures varies depending on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-ventilated area, and work with approved safety
equipment, such as dust masks that are specially designed to filter out microscopic particles. Where
((
ON
))
use of a dust extraction
device is possible, it should be used. To achieve a high level of dust collection, use an industrial
HEPA vacuum cleaner. Observe OSHA 29 CFR part 1926.57 and 1926.103.
WARNING
Sawing, grinding and drilling generate dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory
tract. To avoid breathing impairment, always employ dust controls and protection suitable to the material being sawed or
drilled; See OSHA (29 CFR Part 1910.1200).
8
MK-660 Tile Saw
SAFETY
ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS
))
ON
((
In order to prevent electrical shock and injury, the following electrical safety precautions and symbols
should be followed at all times!
WARNING
In case of a malfunction or breakdown, grounding provides a path of least resistance for electrical
current to reduce the risk of electric shock. This tool is equipped with an electric cord which has an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not modify the plug provided - if it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
• Improper connections of the equipment-grounding conductor can result in a risk of electric shock. The equipment-grounding conductor is the insulated conductor that has an outer surface that is green, with or without yellow stripes. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
• Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
• Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet that looks like the one shown in Sketch A.
The tool has a grounding plug that looks like the plug illustrated in Sketch A. A temporary adapter,
which looks like the adapter illustrated in sketches B and C, may be used to connect this plug to a
2-pole receptacle as shown in Sketch B, if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, plug, and the like, extending from the adapter, must be connected
to a permanent ground, such as a properly grounded outlet box.
Metal Screw
Grounding
Pin
(A)
Cover of
Grounded
Outlet Box
(B)
ADAPTER
(C)
Grounding
Means
Grounding
Pin
(D)
Circuit and Adapter Information
NOTE:
Use of a temporary adapter is not permitted in Canada.
NOTE:
If permanently connected this tool should be connected to a grounded metal permanent
wiring system; or to a system having an equipment - grounding conductor.
9
MK-660 Tile Saw
SAFETY
ELECTRIC MOTOR SAFETY
((
For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the electric motor. Protect the electric motor from dust as much as possible and keep
ON
))
ventilating
openings
clean. Before plugging in the machine, make sure that the outlet voltage is within
the voltage marked on the machines's data plate.
CAUTION
DO NOT spray water on the electric motor. Do not touch the plug with wet hands. To reduce
the risk of electrocution, keep all connections dry and off the ground.
DO NOT operate electric motor in an explosive environment.
DO))NOT EXPOSE TO RAIN
DO NOT expose to rain or use in damp locations.
((
ON
WARNING
If operating the equipment in damp locations is unavoidable, always use a Ground Fault
Circuit
Interrupter, Always wear rubber gloves and footwear in damp conditions.
)
ON
((
)
((
ON
Do Not abuse the cord. Never use the cord to carry the equipment or to pull the plug from
the
)) outlet. Keep the cord away from heat, sharp edges, and moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
((
WARNING
To reduce the risk of electrocution, keep all connections dry and off the ground. A Ground Fault
Circuit Interrupter (GFCI) should be provided on the circuit(s) or outlet(s) to be used for this
ON
machine.
Receptacles
are available having built-in GFCI protections and may be used for this
))
measure of safety. When using an extension cord, GFCI should be installed closest to the power
source, followed by the extension cord and lastly, the machine.
WARNING
The water pump requires a GFCI. To reduce risk of electrical shock when operating the machine
with the pump plugged into the 3-pole receptacle on the motor, connect the machine to a GFCI
outlet. See the pump manual and informational tags enclosed separately for all pump information.
10
MK-660
Tile Saw
ON
)
SAFETY
((
)
WARNING
To avoid the possibility of the appliance or plug receptacle getting wet, position the machine to one side of a wall mounted receptacle. This will prevent water from dripping into the receptacle or plug. A
"drip loop," shown in the picture below, should be arranged by the user to properly position the power cord relative to the power source. Use the drip loop as a way to prevent GFCI and plug from getting
wet.
The "drip loop" is that part of the cord below the level of the receptacle (or the connector, if an extension cord is used). This method of positioning the cord prevents the travel of water along the power
cord and coming in contact with the receptacle.
If the plug or receptacle gets wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and examine for presence of water in the receptacle.
Power
Cord
Power
Tool
Supporting
Surface
Drip Loop
))
((
ON
Drip Loop Information
WARNING
Use only extension cords that are intended for outdoor use. These extension cords are
identified by a marking "Acceptable for use with outdoor appliances; store indoors while not
in use." Use only extension cords having an electrical rating not less than the rating of the
product. Do not use damaged extension cords. Examine extension cords before using and
replace if damaged. Do not abuse extension cords and do not yank on any cord to disconnect. Keep cords away from heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from the extension cord.
ALWAYS make certain that the power source required for the electric motor is correct and always
use the correct NEMA configuration plug. Motors can burn out when the line voltage falls 10% below
the voltage rating of the motor. Failure to use proper voltage will cause the motor to overheat. Make
certain that the correct size grounded (3-wires) extension cord is used.
11
SAFETY
((
ON
MK-660
Tile Saw
))
WARNING
Use of undersized extension cords result in low voltage to the motor that can result in motor burnout
and premature failure. MK Diamond warns that equipment returned to us showing signs of being run
in a low voltage condition, through the use of undersized extension cords,will be repaired or replaced
totally at the customer’s expense. There will be no warranty claim.
To choose the proper extension cord,
• Locate the length of extension cord needed in the table below.
• Once the proper length is found, move down the column to obtain the correct AWG size required for that length of extension cord.
EXTENSION CORD LENGTH
115V
25'
50'
75'
100'
150'
200'
250V
50'
100'
150'
200'
300'
400'
0-5
16
16
16
14
12
12
5.1 - 8
16
16
14
12
10
•
8.1 - 12
14
14
12
10
•
•
12.1 - 15
12
12
10
10
•
•
15.1 - 20
10
10
10
•
•
•
Nameplate
Amperes
12
MK-660 Tile Saw
SAFETY
SAFETY LABEL LOCATIONS
The warning labels contain important safety information. Please read the information contained on
each safety label. These labels are considered a permanent part of your saw. If a label comes off or
becomes hard to read, contact MK Diamond or your dealer for a replacement.
Label B
Label A
Label G
Label C Label D Label E Label F
! WARNING
! WARNING
For Your Own Safety Read Instruction Manual
Before Operating Saw.
Wear Eye Protection.
Disconnect Saw Before Servicing, when Changing
Cutting Wheels and Cleaning.
Use Tool Only with Smooth Edge Cutting Wheels
Free of Openings and Grooves.
Replace Damaged Cutting Wheel Before Operating.
Do Not Fill Water Bath Above Water Fill Line.
See Manual for Pump Replacement.
Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in
their composition may give off dust or mists containing crystalline silica. Silica is a basic
component of sand, quartz, brick clay, granite and numerous other minerals and rocks.
Repeated and/or substantial inhalation of airborne crystalline silica can cause serious
or fatal respiratory diseases, including silicosis. In addition,California and some other
authorities have listed respirable crystalline silica as a substance known to cause cancer.
Label B
Label A
For manuals and parts
lists scan the QR code
with your smart phone
! NOTICE
Most Motor Problems are caused by improper
voltage and extension cords. Cord should be
one-piece and short as possible. Cord
selection should match the following table.
1-2 H.P.
115v 230v
25’ 100’ Max. Cord Length No. 12 Wire
50’ 150’ Max. Cord Length No. 10 Wire
75’ 250’ Max. Cord Length No. 8 Wire
Label C
Label G
FOR INFORMATION ON
SERVICE OR
WARRANTY
! CAUTION
! CAUTION
PLEASE CALL
1-800-474-5594
This saw is to be used
with a Ground Fault
Circuit Interrupter.
Receptacle is for
water pump only.
125V, .6 amps max.
Label D
Label E
Label F
Tile Master Label Sheet Part#166012
Decal/Label
A
B
C
D
E
F
G
Location
Cutting Head
Cutting Head
Cutting Head
Cutting Head
Cutting Head
Cutting Head
Cutting Head
Front
Front
Back
Back
Back
Back
Back
Description
Warning - Read Owner's Manual
Warning - Silica Warning
Notice - Voltage / extension cords
Service / Warranty
Caution - Use with GFCI only
Caution - Receptacle for water pump
QR Manuals
13
MK-660 Tile Saw
SAFETY
PRODUCT SPECIFICATIONS
The MK-660 Saw is a versatile Tile Saw. Operated and used according to this manual, the
MK-660 will provide years of dependable service.
General Description
The MK-660 Saw is engineered as a tabletop or stand mounted wet tile saw. The saw includes a
powerful 120v electric motor. The saw is capable of cutting tile up to fourteen (14) inches in length.
The saw can cut an object two (2) inches thick in one pass.
Motor Specifications
Motor specifications for the MK-660 Saw are listed in the table below:
Voltage
Motor Only Amperage
Frequency
RPM
Horse Power
Weight
120v
8.8 a
60Hz
3500 rpm
3/4 hp
53 lbs.
Blade Capacity
The MK-660 Saw uses a seven (7) inch (178mm) diameter, wet cutting continuous rim, MK Diamond
blade with a five-eighths (5/8) inch (15.875 mm) arbor.
Tile Types
The MK-660 Saw can cut a variety of tile types including stone, masonry, and lapidary products.
NOTE: The MK-660 Saw is not designed to cut plastic or metals.
14
MK-660 Tile Saw
UNPACKING
UNPACKING
Your MK-660 Saw has been shipped from the factory thoroughly inspected. Only minimal assembly
is required.
CAUTION Use proper lifting techniques when lifting the MK-660 Saw.
If not done, remove the MK-660 Saw, Cutting Head and accessory box from the carton.
CONTENTS
In your container, you will find one (1) MK-660 Frame and Water Pan, one (1) MK-660 Cutting Head,
(1) Cutting Head Height Adjusting Knob, (1) Height Adjusting Knob Flat Washer, one (1) 7-inch Wet
Cutting Continuous Rim Diamond Blade, one (1) Adjustable Cutting Guide, one (1) Electric Water
Pump, one (1) Pump Discharge Fitting, one (1) Cooling Transfer Tube, one (1) Flow Adjusting
Clamp, one (1) Drain Plug, one (1) Blade Wrench, one (1) Table Clip, one (1) Inner Flange Wrench,
(1) Splash Guard, one (1) Owner's Manual, one (1) Pump Manual and one (1) Warranty Card.
MK-660 Frame
and Water Pan
MK-660 Cutting
Head
Height Adjusting
Knob
Height Adjusting
Knob Flat Washer
Diamond Blade
Adjustable
Cutting Guide
Electric Water
Pump
Pump Discharge
Fitting
Cooling Transfer
Tube
Flow Adjusting
Clamp
www.mkdiamond.com
MK-660 SerieS
OWNERS MANUAL
PARTS LIST &
OPERATING INSTRUCTIONS
Revision 100
04.2010
Manual Part# 153461
Caution: Read all safety and operating instructions
before using this equipment. This parts list MUST
accompany the equipment at all times.
Drain Plug
Blade Wrench
and Table Clip
Inner Flange
Wrench
MK DiaMonD Warranty CarD
Name
address
City
state
zip Code
phoNe
Fax
e-mail
produCt model
part NumBer
maChiNe serial#
where did you purChase this saw From? Name
q tile distriButor
q tool supply
date purChased
q home CeNter
q equipmeNt supply house
q Bldg material supply
are you a do-it-yourselFer q
or CoNtraCtor q
IF so, what type? tile q
q reNtal equipmeNt house
masoNry q
other
what Criteria was importaNt iN ChoosiNg this saw? (rate From 1 to 5, 5 BeiNg the most importaNt)
priCe
power
preCisioN
portaBility
availaBility
other
CommeNts or suggestioNs:
mK diamoNd warraNty 1315 Storm Parkway, Torrance, CA 90509 USA | www.mkdiamond.com | 1.800.421.5830 | 1.310.539.5158
If within one (1) Year from the date of purchase, this MK Diamond saw fails due to defect in material or workmanship, MK will repair it, free of charge when the unit is returned to the dealer where it was purchased. This warranty DOES NOT cover normal wear or damage resulting from operator abuse. In no event shall MK Diamond Products,
Inc. be liable for consequential damages arising out of the failure of any product if operated improperly. MK Diamond Products may act as a warranty station for motor/engine repairs based on an individual agreement with the manufacturer. This warranty is in lieu of all other warranties express or implied.
©2010 All Rights reserved. MK Diamond Products, Inc. • P/N 155037 MK Warranty Card (02/10)
Pump Manual
Warranty Card
15
Splash Guard
Owner's Manual
MK-660 Tile Saw
TRANSPORT
TRANSPORT
CAUTION
1. The MK-660 Saw weighs approximately fifty-three (53) pounds; use care when transporting.
2. Never transport the MK-660 Saw with water in the Water Pan.
The MK-660 Saw is designed with a rigid frame and removable Cutting Head. Always use proper
lifting techniques when lifting the MK-660 Saw.
To lift the saw, grasp the front and back of the frame at the lift points shown below.
Cutting Head
Lift Point
Lift Point
STAND (Optional)
CAUTION
The MK-660 Saw weighs fifty-three (53) pounds; follow the guidelines in the TRANSPORT
section when placing it on the stand (MK Diamond Part# 151889).
Note:
If using the Optional MK Diamond Stand, follow these steps:
(A)
Open the stand and place on
flat surface
(B)
Remove Water Basin,
place saw on stand
(D)
Reinstall the Water Basin
16
(C)
Ensure saw frame is
positioned properly
MK-660 Tile Saw
ASSEMbly
Cutting head installation
Follow the assembly instructions to prepare your MK-660 Saw for operation.
NOTE:
If the Cutting Head is installed, go to step next step.
(A)
Place the Flat Washer onto
the Height Adjusting Knob
(B)
Align Cutting Head Pivot
Hole to the Post, Pivot Shaft
(C)
Verify the Cutting Head is
completely installed and seated
on the Pivot Shaft
(D)
Install the Adjusting Knob
DIAMOND BLADE installation
NOTE:
When installing the Retaining Screw, do not “cross-thread" and DO NOT over tighten the
screw.
(A)
Loosen the Blade Guard
Retaining Screw
(B)
Open the Outer Blade Guard to
expose the Retaining Nut and
Flanges
17
(C)
Using the Blade Nut Wrench,
loosen and then remove the
Retaining Nut and Outer Flange
MK-660 Tile Saw
(D)
Locate the Inner Flange
Wrench Retaining Holes
(G)
Install the Retaining Nut and Outer
Flange. Hold the Shaft using the
Inner Flange Retaining Wrench
and tighten using the Blade
Wrench
(E)
Install Diamond Blade
onto Blade Shaft
(F)
Verify the Blade is seated on the
Blade Shaft and direction
of rotation is correct
(H)
Close the Outer Blade Guard
and tighten the Blade Guard
Retaining Screw
(I)
Tighten the Outer Blade Guard
Pivot Screw
ADJUSTABLE CUTTING GUIDE installation
(A)
Loosen adjustable Cutting
Guide retaining thumbscrew and
place it over the movable
Cutting Table Ruler/Stop
ASSEMBLY
(B)
Place the adjustable Cutting
Guide onto the movable Cutting
Table Ruler/Stop and tighten the
retaining thumbscrew
18
MK-660 Tile Saw
ASSEMbly
splash guard installation
Follow the assembly instructions to prepare your MK-660 Saw for operation.
(A)
Install the retaining thumbscrew
through the washer and Splash
Guard, then align to the hole
(B)
Install the Splash Guard
onto the Blade Guard
WATER PUMP installation
(A)
Install Water Pump Discharge
Fitting
(B)
Press one end of the Cooling
Transfer Tube onto the Water
Pump Discharge Fitting
(C)
Slide Cooling Flow Adjusting Clamp
onto the Cooling Transfer Tube
PRE-START INSPECTION
Prior to beginning work, a pre-start inspection of the saw should be preformed.
(A)
Ensure the ON/OFF Switch is in
the OFF position
(B)
Verify the movable Cutting
Table moves freely
19
(C)
Inspect the Diamond Blade for
damage - verify the blade is correct
for the material being cut
MK-660 Tile Saw
(D)
Inspect the Pump Assembly for
damage - ensure the cord is free
of cracks or cuts
ASSEMBLY
(E)
Inspect the MK-660 for damage - ensure the cord is free
of cracks or cuts
connecting the water pump
Prior to beginning work, a pre-start inspection of the saw should be preformed.
WARNING 1.
2.
NOTE:
To prevent the possibility of electrical shock, the MK-660 Saw MUST be de-energized when connecting the Water Pump.
To prevent the possibility of electrical shock, use only MK Diamond qualified
replacement parts.
To prevent pump damage, the Water Pump must be disconnected if cutting with a Dry Blade.
(A)
Connect the Coolant Transfer
Tube to the inlet connection of
the Blade Guard
(B)
Connect the Water Pump power
cord to the connection found on
the back of the motor
20
MK-660 Tile Saw
ASSEMbly
Water pump setup for operation
The Water Pump can be setup for operation in two ways, External Water Source or Re-circulation.
NOTE:
To prevent pump damage, the Water Pump must be disconnected if cutting with a Dry Blade.
(A)
Remove the Drain Plug
(B)
Place the Water Pump
in an external container
(C)
Fill the external container until
water completely covers the
Water Pump suction
(A)
Place an external catch Basin
below the Water Pan drain
hole
recirculation
NOTE: When using the re-circulation method, the water should be changed often for longer pump life.
(A)
Ensure the Drain Plug is installed in the Water Pan
(B)
Place the Water Pump in the
back of the Water Pan
21
(C)
Fill the Water Pan until water
completely covers the Water
Pump suction
MK-660 Tile Saw
OPERATION
MK-660 SAW SETUP for operation
CAUTION
1. Check for damaged, broken, or missing parts.
2. Verify the On/Off switch is in the OFF position.
3. Before connecting the MK-660 Saw to a power supply, be sure the voltage, cycle and phase of the job site power source meet the requirements of the table below:
VOLTAGE:
CYCLE:
PHASE:
120v
60hz
1-phase
4. If using an extension power cord, make sure the length and wire gauge
correspond to the requirements listed in the table on page 10. An extension
power cord that is too small in wire gauge (diameter), or too long in length, will cause the motor to overheat and could cause premature failure.
5. Use an approved Ground Fault Circuit Interrupter (GFCI).
6. Do not cover the motor vents as this could lead to motor overheating.
NOTE: In order to avoid breaker tripping, a 20-amp circuit breaker should be used.
(A) Ensure the ON/OFF Switch is in the OFF position
(B) Plug MK-660 Saw into the GFCI
(C) Plug the GFCI into the power source
NOTE: MK Diamond has available, as an accessory item, (Part # 152610) a plug-in GFCI that
may be plugged into a properly installed and grounded 3-pole outlet.
Portable Generator
If using a portable generator to provide power, ensure the generator meets the following minimum
66.7/33.3 amps Single Phase
requirements: 8 KW 120/240 volts 22
MK-660 Tile Saw
OPERATION
CUTTING STRAIGHT EDGES
CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for
which it was designed.
(A)
Loosen the adjustable Cutting
Guide retaining thumbscrew
(B)
Position the adjustable Cutting
Guide to desired cut length
indicated inside the diamond
(C)
Tighten the retaining thumbscrew
(D)
Place the tile against the
Ruler/Stop and Cutting Guide
(E)
Turn the motor ON
(F)
Verify flow on both sides of the
blade (See Maintenance Section
to adjust flow)
(G)
Perform the cut
(H)
Turn the motor OFF when
work is complete
23
MK-660 Tile Saw
OPERATION
diagonal cutting
NOTE: To cut 45º Diagonals, the 45º Flat Angle Guide (MK Diamond Part No. 134577-MK) should be
used.
CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for
which it was designed.
(A)
Remove the adjustable Cutting Guide
(B)
Place the Dual 45° Flat Angle
Guide on the Ruler/Stop
(D)
Position the tile against the
Dual 45° Flat Angle Guide
and the Ruler/Stop
(E)
Turn the motor ON
(G)
Perform the cut
(H)
Turn the motor OFF when
work is complete
(C)
Position the Dual 45° Flat Angle
Guide and tighten the retaining
thumbscrew
NOTE: If cutting the tile in two equal halves, align the tile in the V-notch of the movable Cutting Table Ruler/Stop.
24
(F)
Verify cooling flow on both sides
of the blade (See Maintenance
Section to adjust flow)
MK-660 Tile Saw
operation
45° Miter cutting
NOTE: To cut 45º Miters, the 45º Bullnose Miter Guide (MK Diamond Part No. 153201-MK) should be
used.
CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for
which it was designed.
(A)
Remove the adjustable Cutting Guide
(B)
Place the 45° Bullnose Miter
Guide on the Ruler/Stop
(C)
Position the 45° Bullnose Miter
Guide and tighten the retaining
thumbscrew
(D)
Position the tile on the 45°
Bullnose Miter Guide and the
Ruler/Stop
(E)
Turn the motor ON
(F)
Verify cooling flow on both sides
of the blade (See Maintenance
Section to adjust flow)
(G)
Perform the cut
(H)
Turn the motor OFF when
work is complete
25
MK-660 Tile Saw
OPERATION
off-angle cutting
NOTE: To cut angles other than 45º angles, a Protractor (MK Diamond Part No. 134569-MK) should be
used.
CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for
which it was designed.
(A)
Remove the adjustable Cutting Guide
(D)
Position the Protractor cutting
guide to the desired cut length
indicated inside the diamond
(G)
Turn the motor ON
(B)
Place the Protractor on the
Ruler/Stop
(E)
Tighten the retaining
thumbscrew
(H)
Verify flow on both sides of the
blade (See Maintenance Section to adjust flow)
26
(C)
Set the desired angle and tighten
the thumbscrew
(F)
Position the tile against the Protractor and the Ruler/Stop
(I)
Perform the cut
MK-660 Tile Saw
cleanup
(J)
Turn the motor OFF when
work is complete
cleanup
NOTE: 1. If an external water source was used, steps A through C may be skipped.
2. Dispose of wastewater in accordance with applicable Federal, State and Local laws.
(A)
Clean the Water Pump suction of all debris
(B)
Place the Water Pump in an
external container
(C)
Run the MK-660 Saw until clear
water is seen at the blade coolant
ports (Approx. one (1) minute)
CAUTION Ensure the saw is disconnected before completing the remnder of the cleanup
process.
(D)
Ensure the ON/OFF switch is
in the OFF position
(E)
Unplug the GFCI from the
power source
27
(F)
Unplug MK-660 from the
GFCI
MK-660 Tile Saw
(G)
Clean the MK-660 Saw with
soap and clean water
(H)
Remove the Water Pan from
the MK-660 Saw
cleanup
(I)
Clean the Water Pan
CAUTION Ensure water is not forced into the motor casing when cleaning.
(J)
Clean the movable Cutting
Table Guide Bar
(K)
Clean the movable Cutting
Table Roller Wheel Frame
Support
(L)
Clean the remainder of the
MK-660 Saw
Maintenance following use
To extend the life of the MK-660 Saw, the following procedure should be performed after each use.
Lubricate all points listed below with light oils such as, 3 in 1, WD-40, etc.
(A)
Ensure the ON/OFF switch is
in the OFF position
(B)
Unplug MK-660 Saw
28
(C)
Lubricate the Guide Bar
MK-660 Tile Saw
maintenance
(D)
Lubricate the Roller Wheel
Assembly
Monthly Maintenance
The following maintenance should be performed monthly.
(A)
Remove the Diamond Blade
(B)
Lubricate the Outer Flange and
Retaining Nut
(C)
Remove the Outer Blade
Guard
(D)
Remove the Inner Flange
(E)
Clean around the Motor Shaft
and clean the Inner Flange
(F)
Lubricate the Motor Shaft
and Inner Flange
29
MK-660 Tile Saw
maintenance
(G)
Locate the Motor Shaft Alignment Pin
(H)
Align the Alignment Slot of the
Inner Flange to the Motor Shaft
Alignment Pin and install the
Inner Flange
(I)
Lubricate the Outer Blade
Guard Pivot Shaft
(J)
Install the Outer Blade Guard
(K)
Remove the Cutting Head
(L)
Lubricate the Cutting Head
Pivot Shaft
(M)
Lubricate the Cutting Head
Adjustment Knob
(N)
Lubricate the Cutting Head Adjustment Knob retaining holes
(O)
Lubricate the Cutting Head
Pivot Hole
30
MK-660 Tile Saw
maintenance
(P)
Verify the Cutting Table Roller
Wheel Assembly is tight
flow adjustment
NOTE: If flow to the Diamond Blade requires adjustment, perform the following actions:
(A)
Increase cooling flow by
releasing the Flow Adjusting
Clamp
(B)
Reduce cooling flow by Pressing down on the Flow Adjusting
Clamp
31
MK-660 Tile Saw
maintenance
BLADE DRESSING
Like most cutting instruments, a Diamond Blade performs best when it is dressed. Over time and
use, diamonds on the outer edge of the blade will become smoothed or "glazed" over. This will
reduce grinding efficiency and may cause the blade to "wander" or bend giving the illusion of an
alignment problem. When this occurs, the blade will need to be dressed. The Diamond Blade can be
dressed using the MK Dressing Stick (part# 152972) and by following the steps below.
(A)
Setup the MK-660 Saw for
operation (see Setup, Adjustment and Operation)
(D)
Turn the motor ON
(B)
Set the adjustable Cutting
Guide to cut a 1/16-strip
(C)
Position the Dressing Stick
(E)
Verify flow on both sides of
the blade (See Maintenance
Section to adjust flow)
(F)
Cut the Dressing Stick
seven (7) or eight (8) times
to dress the Blade
(G)
Ensure the ON/OFF switch is
in the OFF position
32
MK-660 Tile Saw
maintenance
Diamond blade change-out
NOTE: When installing the Retaining Screw, do not "cross-thread" and DO NOT over tighten the screw.
(A)
Open the Outer Blade
(B)
Remove Retaining Nut and
Outer Flange
(D)
Install the Diamond Blade
onto Blade Shaft
(E)
Verify the Blade is seated on
the Blade Shaft and direction of
rotation is correct
(G)
Close the Outer Blade Guard
and tighten the Blade Guard
Retaining Screw
(H)
Tighten the Outer Blade Guard
Pivot Screw
33
(C)
Remove Diamond Blade
from Blade Shaft
(F)
Install the Retaining Nut and Outer
Flange. Hold the Blade Shaft
using the Inner Flange Retaining Wrench and tighten using the
Blade Wrench
MK-660 Tile Saw troubleshooting
Blade will not cut properly
(A)
Check for Smoothness or
“Glazing" (Dress blade if
needed)
(B)
Check for proper rotation
(D)
Verify the blade is correct for
the material being used
Movable Cutting Table Does Not Move Correctly
(A)
Check that the Guide Bar is
clean – clean if dirty
(B)
Check the movable Cutting
Table Roller Wheel for wear
replace if necessary
34
(C)
Ensure the Blade Core is not
bent and Arbor is not out of
round
MK-660 Tile Saw troubleshooting
Cooling Flow
(A)
Check Flow Adjusting
Clamp is open. If flow exists,
go to Step B
(B)
Remove the Transfer Tube
from the Blade Guard inlet,
go to Step C
(C)
Place Pump into a bucket of
water and check flow. If flow
exists, go to Step D
Intake Screen
(D)
Remove the Transfer Tube
and check flow. If flow exists,
go to Step F
(E)
Remove the Pump Discharge
Fitting and check flow. If flow
exists, go to Step F.
(F)
Remove the Pump Intake
Screen and check for debris.
If flow exists, go to Step G.
(G)
Remove the Blade Guard
Intake Fitting, go to Step H.
(H)
Clean the Blade Guard
Intake Fitting, go to Step I.
(I)
Rod Cooling Channels and
recheck flow
NOTE:
“Rodding" coolant channels is performed by inserting a small wire rod through
the inlet on top of the Blade Guard and directing the rod out through each of the
flow tubes located on the underside of the Blade Guard. The channels should
be “rodded" until all ports are free of foreign debris.
35
MK-660 Tile Saw troubleshooting
Blade Stops Turning
(A)
Allow motor to cool and
depress motor Overload
Reset Switch
(D)
Verify circuit breaker at least
20 amps - if not, move to
20-amp circuit
NOTE:
(B)
Verify all plugs fully installed
(E)
Verify circuit breaker not
tripped if tripped, reset once
(C)
Check Ground Fault Circuit
Interrupter (GFCI) is not tripped
(F)
Check power source voltage
is 120v - if not 120v, move to
another circuit
Using the proper blade when cutting any material will insure that additional drag
is not induced on the motor thus increasing the amperage draw. Too much drag/
amperage draw can overheat the motor. A sign that the incorrect blade is being
used for the material being cut is if user trips the circuit breaker at the power
supply when cutting the material.
36
NOTES
37
MK-660 Tile Saw 38
exploded view
MK-660 Tile Saw
parts list
Item
Description
Qty
A
Accessories
1
Part #
n/a
A1
Carton, Accessory Pack, 660
1
153498
A3
Wrench, 15/16 Closed End
1
134684
A4
Wrench, Spanner, 660
1
154362
A5
Curtain, Splash
1
134841
A6
Bracket, Splash Curtain
1
152571
151888
A7
Wing-screw, 1/4-20 x 1/2
1
A8
Washer, 1/4 SAE Flat
1
151915
A9
Pump, Water, G-150A
1
151271
A10
Fitting, Plastic, 1/4 FNPT x 1/4 BARB
1
128397
A11
Hose, Vinyl, 1/4 ID
2’
132951
A12
Clamp, Flow, 1/4-1/2
1
154394
A13
Owner’s Manual, Water Pump
1
155745
A14
Rip Guide
Screw, 1/4-20 x 3/4 Thumb
1
1
134551
150991
A15
Large Bullnose Accessory
Screw, 1/4-20 x 3/4 Thumb
1
2
153201
150991
A16
Owner’s Manual, 660
1
153461
A19
Blade, 7 x 060 x 5/8, MK-100
1
153441
B
Blade Guard, 7”, Assembly
1
154811-MK
B1
Guard, 7”Blade
1
151731
B2
Elbow, 1/8 MNPT x 1/4 BARB 90ϒ Brass
1
154652
B3
Knob, Davies
1
151681
B4
Washer, 5/16 SAE Flat
2
151754
B5
Wing-nut, 5/16-18 Nylock
1
151746
D
Cutting Head (less blade guard)
1
n/a
D1
Cutting Head, 660
1
154291
D2
Cover, Cutting Head, 660
1
154293
D3
Gasket, Cover, 660
1
154381
D4
Screw, 10-24 x 5/8 Pan Head Phillips Self-Tapping Machine
8
153681
D5
Screw, 5/16-18 x 2 1/2 Hex Head Cap, Fully Threaded
1
151748
D6
Washer, 5/16 Split Lock
1
151747
D7
Motor, 3/4 HP 115V FWR, 660
1
154292
D7A
Motor, 3/4 HP 230V FWR, 660
1
153497
D8
Gasket, Thermal, 660
1
154346
D9
Screw, 10-24 x 5/8 Flat Head Phillips Machine
4
154295
D10
Flange, Inner, 660
1
154194
D11
Pin, 1/8 x 3/8 Spring
1
154982
D12
Flange, Outer
1
135830
D13
Nut, 5/8-18 UNF Hex
1
135848
D14
Cord, AC Power 120V (16/3 SJTW x 10’, w/ molded 5-15P and Heyco
3251 Strain Relief)
1
153419
D15
Cord, Pump Pigtail, 16/3 SJTW x 1’, w/ molded 5-15R and Heyco 3251
Strain Relief
1
154446
D16
Wire Harness, 660
1
153415
D17
Screw, 10-24 x 3/8 Pan Head Phillips Self-Tapping Machine
1
151262
D18
Resistor, 660
1
153535
D19
Tack, 1/4 Head
4
155659
D20
Switch, Thermal Overload, 660
1
167982
39
MK-660 Tile Saw
parts list
Item
Description
Qty
Part #
D21
Boot, Thermal Overload Switch
1
167983
D22
Switch, 15A\125V Lighted Rocker
1
153421
D23
Rectifier, 40 Amp
1
153677
D24
Screw, 10-24 x 3/4 Fillister Head Machine
1
151750
D25
Wire-nut, 3/#16 AWG (Blue)
1
155492
D26
Tag, 660 Serial Number
1
156561
D27
Label, Caution Strip
1
155214
D28
Label, When Motor Cools…
1
154409
E
Frame
1
n/a
E1
Frame
1
153322
E2
Pan, Plastic
1
151736
E3
Plug, Water Drain
1
153439
E4
Plate, Adjustment
2
151758
E5
Pin, Rolled
2
151783
F
Guide Bar, 5/8 Dia.
1
151739-MK
F1
Bar, Guide, 5/8 Dia.
1
151739
F2
Cover, Guide Bar
1
151740
F3
Spacer, 5/8 Guide Bar Cover
2
151755
F4
Screw, 5/16-18 x 1 Hex Head Cap
2
151743
F5
Washer, 5/16 Split Lock
2
151747
F6
Washer, 5/16 SAE Flat
2
151754
G
Linear Bearing
1
151737-MK
G1
Casting, Bearing, Linear
1
151737
G1a
Bearing, Multi-Lube
2
151781
G2
Screw, 5/16-18 x 1 Hex Head Cap
2
151743
G3
Washer, 5/16 Split Lock
2
151747
G4
Washer, 5/16 SAE Flat
2
151754
H
Post
1
n/a
H1
Post, Rear, 660
Shaft, 5/8 Pivot, 660
1
1
153451
153452
H2
Screw, 3/8-16 x 2 Hex Head Cap
2
153485
H3
Screw, 3/8-16 x 1 Hex Head Cap
1
152507
H4
Washer, 3/8 Split Lock
3
150925
H5
Washer, 3/8 SAE Flat
4
150923
H6
Knob, 3/8-16 x 1-1/2 MK Adjustment
1
156770-02
J
Roller Wheel
1
151756
J1
Bracket, Roller Wheel
1
154021
J2
Wheel, Roller
1
151799
J3
Screw, 1/4-20 x 1 1/2 Hex Head Cap
1
151914
J4
Washer, 1/4 SAE Flat
1
151915
J5
Nut, 1/4-20 Hex
1
151893
K
Table, 660
1
n/a
K1
Table, 660
1
152680
K2
Screw, 5/16-18 x 1 Hex Head Cap
2
151743
K3
Washer, 5/16 Split Lock
2
151747
K4
Washer, 5/16 SAE Flat
2
151754
40
MK-660 Tile Saw
ITEM
NUMBER
DESCRIPTION
1.
158434
MK-225, 7 x 5/8 Arbor
2.
139311
MK-215, 7 x 5/8 Arbor
3.
153293
MK-315, 7 x 5/8 Arbor
4.
134577-MK
Dual 45° Flat Angle Guide
5.
134569-MK
90° Protractor
6.
152792
Dressing Stone
7.
152601
Ground Fault circuit Interrupter
8.
153201-MK
9.
151889
45° Miter
Saw Stand
41
ACCESSORIES
MK-660 Tile Saw Ordering & return instruction
ORDERING INFORMATION
You may order MK Diamond products through your local MK Diamond distributor or, you may order
direct from MK Diamond.
When ordering direct from MK Diamond, please have the following information ready before calling:
• The Model Number of the saw
• The Serial Number of the saw
• Where the saw was purchased and when
• The Part Number for the part(s) being ordered
• The Part Description for the part(s) being ordered
NOTE: There is a $25.00 minimum order when ordering direct from MK Diamond. A $6.00 charge will
be added to orders having a net billing value under $50.00. All purchases must be made using VISA,
MasterCard or American Express.
All parts may be ordered by calling toll free to – 800 421-5830 or 310 539-5221 and asking for
Customer Service. For technical questions, call – 800 474-5594.
RETURN MATERIALS POLICY
To expedite the service relative to the return of a product purchased through MK Diamond, please
observe the following:
NOTE: When returning all items, they must have been purchased within the previous twelve (12)
months.
• Have the Model Number of the saw
• Have the Serial Number of the saw
• Have the location of where the saw was purchased
• Have the date when the saw was purchased
• Contact Customer Service for approval to return the item(s)
• Obtain a Returned Goods Number (RGA) authorizing the return
• Follow the packaging instructions in the following section
• Ensure your item(s) are prepaid to the destination
For returned items, call toll free to – 800 421-5830 or 310 539-5221 and ask for Customer Service.
For technical questions, call – 800 474-5594 or 310 257-2845.
PACKAGING INSTRUCTIONS
• Remove the Cutting Head and Support Angle Assembly
• Dry the saw before shipping
• When packing, include the following: Saw, Diamond Blade, Blade Guard and Support Angle Assembly and Adjustable Cutting Guide (Other Accessories are not required)
• Package the unit in its original container or one of comparable size (do not ship the unit partially exposed)
• Ensure all parts are secured in the packaging to prevent moving
AUTHORIZED SERVICE CENTERS
For quicker repair time, you may contact MK Diamond Customer Service, toll free, at 800 421-5830
or 310 539-5221 for the Authorized Service Center closest too you or visit our web site at
www.mkdiamond.com. For technical questions, call – 800 474-5594.
42
MK-660 Tile Saw
CONTACT & WARRANTY
CONTACT
Please contact MK Diamond Products, Inc. Customer Service Department with any questions you
might have regarding distributors, parts or service.
Telephone: (800) 421-5830
Fax: (310) 539-5158
E-mail: [email protected]
Customer Service Hours: Monday through Friday, 6AM-4PM PST
MK Diamond Products, Inc.
1315 Storm Parkway
Torrance, CA 90501
MK DIAMOND PRODUCTS, INC. LIMITED WARRANTY
MK DIAMOND PRODUCTS, INC. will guarantee every machine they build, to be free from defects in
material and workmanship for (1) one year from date of purchase. The obligation of MK DIAMOND
PRODUCTS, INC. under this warranty is limited to the repair or replacement of any parts which,
under normal use, prove to be defective in material or workmanship. The parts involved or the unit
in question should be returned to MK DIAMOND PRODUCTS, INC. or to a point designated by us,
transportation prepaid.
This warranty does not obligate us to bear the cost of labor or transportation charges in connection
with replacement or repair of defective parts. Likewise, it shall NOT apply to any unit which has been
subjected to misuse, neglect or accident. This warranty does NOT apply to any machine which has
been repaired or altered outside our factory.
This warranty does NOT obligate MK DIAMOND PRODUCTS, INC., with respect to items not of our
manufacture, such as engines, motors, hydraulics, etc., which are subject to their own guarantees and
warranties.
We shall in no event be liable for consequential damages or contingent liabilities arising out of failure
of any equipment or parts to operate properly.
© COPYRIGHT 2014, MK DIAMOND PRODUCTS, INC. ALL RIGHTS RESERVED.
The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used,
reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
MK Diamond may have patents, patent applications, trade marks, copyrights of other intellectual
property right covering this product in this document.
This manual MUST accompany the equipment at all times. This manual is considered a permanent
part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for
printing.
43
MK-660 TILE SAW
OWNER'S MANUAL, PARTS LIST
& OPERATING INSTRUCTIONS
MK Diamond Products, Inc.
1315 Storm Parkway
Torrance, CA 90501
Toll-Free: (800) 421-5830
Phone: (310) 539-5221
Fax: (310) 539-5158
www.mkdiamond.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement