Cctv camera pros | SH-600M4 | User manual | cctv camera pros SH-600M4 User manual

cctv camera pros SH-600M4 User manual
CCTV Camera Pros – Wireless Camera System
SH-200M1 & SH-600M4
User Manual
www.cctvcamerapros.com
888-849-2288
Contents
This user manual describes how to setup, install and operate the Shepherd-200M1 & 600M4. Please read it carefully and
observe all instructions and warnings before commencing installation of the product. Retain this manual with the original bill of
sale for future reference.
FCC Interference Statement ........................................................................................................
4
FCC Radiation Exposure Statement ....................................................................................................... 5
Manufacturer's Disclaimer Statement ..................................................................................................... 5
Regulations ............................................................................................................................................. 6
1. System Introduction ........................................................................................... 8
1.1 Features ............................................................................................................................................ 9
1.2 Configuration................................................................................................................................... 10
2. System Hardware .............................................................................................. 11
2.1 Package Contents ........................................................................................................................... 11
2.2 Hardware Connections ................................................................................................................... 12
2.3 LED Panel ....................................................................................................................................... 15
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 2
3. System Setup and Configuration .................................................................... 17
3.1 Installing MagicLink ......................................................................................................................... 17
3.2 Configuring the Shepherd- 200M1 & 600M4 Transmitter and Receiver ......................................... 21
Re-configuring the Shepherd-200M1 & 600M4 Transmitter ..................................................................................... 21
Configuration Default Settings.................................................................................................................................. 28
Re-configuring the Shepherd-200M1 & 600M4 Receiver ......................................................................................... 36
4. System Hardware Assembly and Installation ................................................ 37
4.1 System Location ............................................................................................................................. 37
4.2 System Assembly............................................................................................................................ 42
Before Commencing Installation .............................................................................................................................. 42
Notice ....................................................................................................................................................................... 42
Pole Mounting .......................................................................................................................................................... 44
Wall Mounting .......................................................................................................................................................... 45
4.3 Aligning the Transmitter and Receiver ............................................................................................ 47
5. Trouble Shooting .............................................................................................. 50
6. Settings Record ................................................................................................ 53
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 3
Statements
FCC Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
This 5.8GHz wireless video system has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment or device.
z Connect the equipment to an outlet other than the Receiver's.
z Consult a dealer or an experienced radio/TV technician for assistance.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 4
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 23cm between the radiator and your body.
Manufacturer's Disclaimer Statement
The information given in this document was current when published. The company reserves the right to make changes to the
content of this document and/or the products associated with it at any time without obligation to notify any person or
organization. All information is subject to change without notice and does not represent a commitment on the part of vendor.
No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any
particular purpose of this document. In no event will the manufacturer be liable for direct, indirect, special, incidental or
consequential damages arising out of the use or inability to use this product or documentation, even if advised of the
possibility of such damages. This document contains materials protected by copyright. All rights are reserved. No part of this
manual may be reproduced or transmitted in any form, by any means or for any purpose without express written consent of its
authors. Product names appearing in this document are mentioned for identification purposes only. All trademarks, product
names or brand names appearing in this document are registered property of their respective owners.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 5
Regulations
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 6
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 7
1. System Introduction
CCTV Camera Pros Shepherd-200M1 & 600M4 represents an all new, high performance, digital based wireless surveillance
camera transmission system. Offering exceptional bandwidth and serial data transmission, the Shepherd-200M1 & 600M4
brings a wireless capability to all traditional fixed cameras and supplies built-in remote control of RS485 based full/half-duplex
PTZ dome cameras, providing an excellent yet cost effective solution for remote and hard-to-reach camera locations.
The Shepherd-200M1 & 600M4 uses the latest digital wireless OFDM modulation in the less crowded (and unlicensed) 5GHz
radio band, providing transmission rates that significantly reduce signal interference. Being fully-duplex, the Shepherd- 200M1
& 600M4 supplies a very stable wireless link, which combines with our image processing software to deliver hi-definition,
full-motion, ripple free video up to 4 miles (SH-600M4) or 1 mile (SH-200M1) with direct line-of-sight. The Shepherd-200M1 &
600M4 also offers considerably improved data security via either AES or RC4 key encryption.
The Shepherd-200M1 & 600M4 has been designed for ease-of-use and flexibility. System set-up and configuration are quick
and easy tasks via our MagicLink software, which allows for the selection of personalized encryption keys, the establishment of
the PTZ interface and a choice of transmission ranges for improved image quality. Where transmission of over 10 kilometers is
required or the signal path needs to change direction, two or more Shepherd-200M1 & 600M4s can be connected in series
using the Repeater Mode.
Overall, the Shepherd-200M1 & 600M4 provides a versatile, all-in-one wireless transmission solution for CCTV and traffic
surveillance needs, offering superb performance in all environments and weather conditions, and providing integrators and
installers with a system that is easy to set-up, simple to install and straight-forward to operate, while still offering time and
money saving flexibility.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 8
1.1 Features
z
A fully integrated all-in-one 5.8GHz wireless CCTV solution
z
Wireless transmission for real time video up to 10 Km
z
5.8GHz OFDM for reduced interference
z
Data Rates of up to 54 Mbps
z
Full Duplex provides a stable wireless link
z
Digital Image Processing cuts out signal ripple and snow
z
Advanced security provided by either AES or RC4 key encryption
z
Proprietary serial data transmission for RS485 Full-Duplex & Half-Duplex PTZ control
z
MagicLink software for system configuration
z
User-selectable transmission power and distance
z
Supports NTSC/PAL (720x480 resolution at 30 fps)
z
No signal interference between cameras
z
Easy installation and mounting
z
Rugged, all-weather IP67 enclosure
z
Digital Ethernet output with connection SDK option
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 9
1.2 Configuration
Figure 1a
A standard wireless configuration using the Shepherd-600M4.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 10
2. System Hardware
2.1 Shepherd-200M1 & 600M4 Package Contents
Model Number
Content
Quantity
WA5800-DTX
Transmitter with dBi panel antenna
X1
WA5800-RTX
Receiver with dBi panel antenna
X1
MK-SH23
Mounting Kit for Pole/Wall mount
X2
CD-SH23
CD : MagicLinkSW / User manual
X1
PS-012V1A-01
Power Adapter
X2
CA-SH23
Data Cable Unit
X2
Ml-SH23
User Manual
X1
PS-ADAPTER
Adapter Wire
X2
NOTE: If any of the above items are damaged or missing,
do not install or operate this product. Please contact your
dealer immediately.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 11
2.2 Hardware Connections
Figure 2a
Data cable connections
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 12
(1) Power Input (black cable)
z
Connects to 12 V dc / 1A Female power connector
(2) Video Cable (BNC-Female) (blue cable, silver head)
z
Designed to mate with standard BNC Female connector on camera. This input accepts 75ohm video in both NTSC
and PAL formats
(3) & (4) Audio Cables (Female)- Right (red head) & Left (white head)
z
Designed to mate with standard RCA Female “Lineout” audio source connectors on camera. Each input accepts 1
Vpp audio input and is terminated with 600ohm unbalanced configuration
(5a) RS485 Full Duplex/Half Duplex Twisted-pair cable (T+) (Red cable)
z
Connects to T+ hole on PTZ Full Duplex system camera
z
Connects to T+ hole on PTZ Half Duplex system camera
(5b) RS485 Full Duplex/Half Duplex Twisted-pair cable (T-) (Red-White cable)
z
Connects to T- hole on PTZ Full Duplex system camera
z
Connects to T- hole on PTZ Half Duplex system camera
(5c) RS485 Full Duplex Twisted-pair cable (R+) (Yellow cable)
z Connects to R+ hole of PTZ Full Duplex system camera
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 13
(5d) RS485 Full Duplex Twisted-pair cable (R-) (Yellow-Black cable)
z
Connects to R- hole of PTZ Full Duplex system camera
(6) Waterproof Ethernet RJ45 Jack
z
Connects to PC Via Ethernet cable for configuring the Transmitter and Receiver using MagicLink software
(7) Waterproof D-sub connector
z
It’s waterproof rubber O-ringed head of data cable unit
(8) Video Cable (BNC-Female) (blue cable, silver head)
z
Designed to mate with standard BNC Female connector on TV. This input accepts 75ohm video in both NTSC and
PAL formats
(9) & (10) Audio Cables (Female) - Right (red head) & Left (white head)
z
Designed to mate with standard RCA Female “Line In” audio source connectors on TV. Each input accepts 1 Vpp
audio input and is terminated with 600ohm unbalanced configuration
(11a) RS485 Full Duplex Twisted-pair cable (T+) (Red cable)
z
Connects to T+ hole of PTZ Full Duplex control Keyboard
(11b) RS485 Full Duplex Twisted-pair cable (T-) ((Red-White cable)
z
Connects to T- hole of PTZ Full Duplex control Keyboard
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 14
(11c) RS485 Full Duplex/Half Duplex Twisted-pair cable (R+) (Yellow cable)
z
Connects to R+ hole of PTZ Full Duplex control Keyboard
z
Connects to R+ hole of PTZ Half Duplex control Keyboard
(11d) RS485 Full Duplex/Half Duplex Twisted-pair cable (R-) (Yellow-Black cable)
z
Connects to R- hole of PTZ Full Duplex control Keyboard
z
Connects to R- hole of PTZ Half Duplex control Keyboard
2.3 LED Panel
Figure 2b
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 15
No.
LED
Color
Status
1
Power
Green
ON
Unit power on
OFF
Unit power off
ON
Strength 1: The Transmitter’s signal is successfully being received by the
Receiver (minimum strength)
OFF
No connection
ON
Strength 2: The Transmitter’s signal is successfully being received
OFF
No connection
ON
Strength 3: The Transmitter’s signal is successfully being received
OFF
No connection
ON
Strength 4: The Transmitter’s signal is successfully being received
OFF
No connection
ON
Strength 5: The Transmitter’s signal is successfully being received by the
Receiver (maximum strength)
OFF
No connection
2
3
4
5
6
Wireless
Wireless
Wireless
Wireless
Wireless
Green
Green
Green
Green
Green
Description
Wireless Strength 1: only LED 2 on (minimum)
Wireless Strength 2: LED 2, 3 on
Wireless Strength 3: LED 2, 3, 4 on
Wireless Strength 4: LED 2, 3, 4, 5 on
Wireless Strength 5: LED 2, 3, 4, 5 ,6 on (maximum)
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 16
3. System Setup and Configuration
The Shepherd-200M1 & 600M4 operates as an independent system within an integrated security system and does not need
to cooperate with other network systems. Therefore, if all the Transmitter and Receiver default settings are to be used (for
default settings, see Configuration Settings on page 30), the system can be installed as a simple plug-and-play solution.
However, we recommend that for security reasons, every Shepherd- 200M1 & 600M4 system is configured with its own
unique security settings (using the MagicLink software), and, if 2 or more Shepherd-200M1 & 600M4 systems are used in a
single area, it is vital that each be configured with its own Data Encrypt Key and Connection ID.
To re-configure any of the default settings on the Shepherd-200M1 & 600M4, first install the MagicLink software onto a
Windows-based PC or Notebook, then use MagicLink to change the configuration settings of both the Transmitter and
Receiver.
3.1 Installing MagicLink
MagicLink software allows users to re-configure the Shepherd-200M1 & 600M4 via any Windows-based PC or Notebook. This
section describes how to install MagicLink to your PC.
1.
Insert the MagicLink Installation CD-ROM into your computer's CD-ROM drive. Run the SETUP.EXE program from the
CD-ROM. The following window will appear:
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 17
Figure 3a
z
The screen will show the default destination for the MagicLink software chosen by your computer's utility. If you want
z
to install MagicLink to another location, click the Browse button and select an alternative destination.
Click Next when you are ready to continue. The setup program will begin to install the programs into the destination
folder.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 18
2.
When MagicLink has been successfully installed, the following window will appear:
Figure 3b
z
Click Finish to complete the installation.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 19
NOTE: To remove MagicLink from your computer, find and open the MagicLink
folder in your desktop, select Uninstall, and follow the on-screen instructions.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 20
3.2 Configuring the Shepherd-200M1 & 600M4 Transmitter and Receiver
Having installed MagicLink to your computer, follow the procedures below to re-configure the settings in both your Transmitter
and Receiver.
Re-configuring the Shepherd-200M1 & 600M4 Transmitter
1.
Connect your computer to the Ethernet cable of the Shepherd-200M1/600M4 Transmitter.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 21
Figure 3c
2.
1.
Check the status of the Local Network icon on the Windows toolbar.
When the icon is as below, the Windows OS is making the necessary connections.
Figure 3e
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 22
z
2.
Do not open MagicLink whilst this icon is showing.
When the icon is as below, the Windows OS has successfully made the connection.
Figure 3f
3.
Open MagicLink on your computer.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 23
3.
The following MagicLink configuration window will appear:
Figure 3g
1.
Click Get Connection.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 24
4.
Connecting to Device will appear in the dialog section.
Figure 3h
NOTE: If Connection Fail appears in the dialog section, check all cables are properly
connected and try again.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 25
5.
If the connection is successful, Connected will appear in the dialog section.
Figure 3i
1.
Enter your required Configuration Settings (see below for Default Settings).
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 26
NOTE: All configuration settings must be the same for both the Transmitter
and the Receiver, otherwise communication will fail.
NOTE: If the dialog section continues to show Connecting to Device and
does not change to Connected, check your Antivirus software, which might
view MagicLink as a virus. In your Antivirus Program Control Notice dialog,
select Permit Always.
Figure 3j
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 27
Configuration Default Settings
Video Setup
Video System
Default Settings
To select NTSC or PAL video format.
NTSC
Security Setup
(Note: If two or more Shepherd-600M4 sets are used in the same area, each set must be configured with its own
Encrypt Key and Connection ID settings to ensure the security of the connection)
Encrypt method
Select Encrypt method AES or RC4
AES
AES: The most secure wireless encryption available. The
system generates and exchanges keys dynamically, so each
data packet has its own key.
RC4: An encryption method that can be used with virtually all
wireless LAN clients.
Data Encrypt key
The Shepherd-200M1 & 600M4 uses a 128-bit encryption key
for both AES and RC4. Input a key of 6~26 hexadecimal
characters (letters of the alphabet (case sensitive) or
numbers). The Data Encrypt Key cannot be left blank.
Derytech
Connection ID
Input an ID of 1~ 8 hexadecimal characters [letters of the
Derytech
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 28
alphabet (case sensitive) or numbers]. The Connection ID
cannot be left blank.
Wireless Setup
Transmit Range
(Km)
To select the approximate distance between the transmitter
and receiver for an improved transmission link [Options: 1~10
kilometers].
10 Kilometers
Transmit Power
To select the transmit power level. [Options: 1, 2, 3, 4, 5]. (In
normal use, set to 5. When testing, if the TX and RX units are
5 (maximum)
very close (10m), reduce TX Power to avoid signal saturation).
PTZ RS485 Setup (refer to the settings shown on the PTZ controller)
* These settings apply to both Full and Half Duplex systems
** If a standard, non-PTZ camera is connected, there is no need to change these settings
Baud Rate
Options: 200, 2400, 9600 (input from 200-19,000)
9600
Data Bit
Options: 7, 8
8
Parity
Options: None, Even, Odd
None
Stop Bit
Options: 1, 1.5, 2
1
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 29
6.
After inputting the desired configuration settings, click Write Configuration. The following window will appear:
Figure 3k
z
Wait for up to 1 minute for the settings to be written to the device.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 30
7.
When the dialog section shows Successfully, configuration has been completed.
Figure 3l
z
Click Exit
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 31
8.
To complete re-configuration, re-boot the Shepherd-200M1/600M4 by powering off then powering on again.
NOTE: If the dialog section shows Timeout; Please check, the configuration settings have
failed to write to the device. Check all connections and follow procedures 1~9 again.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 32
Figure 3m
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 33
9.
After Re-booting the Shepherd-200M1/600M4, open MagicLink again and click Get Connection.
Figure 3n
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 34
10. Check the configuration settings have been successfully updated.
Figure 3o
z
Click Exit.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 35
11. Remove the Ethernet cable from your PC.
Re-configuring the Shepherd-200M1 & 600M4 Receiver
To re-configure the Shepherd-200M1 & 600M4 Receiver, follow procedures 1-12 for configuring the Shepherd-200M1/600M4
Transmitter above.
NOTE: Be sure to use the same settings for the Shepherd-200M1/600M4 Receiver as have
been used for the Shepherd-200M1/600M4 Transmitter. Take particular care when choosing
and entering the Data Encrypt Key and Connection ID.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 36
4. System Hardware Assembly and Installation
The Shepherd-200M1 & 600M4 is a versatile and easy to use system, however, time and care should be taken when choosing
suitable camera, transmitter and receiver locations and during installation.
4.1 System Location
To obtain the best possible picture quality and transmission distance, follow these general rules of thumb:
1.
Mount the transmitter and receiver as high as possible to avoid human and mechanical traffic and to reduce signal
interference caused by the ground plane.
2.
Keep the transmission path as open as possible. Objects such as walls, roofs and anything metallic near the
transmission path may cause interference to the signal.
3.
Ensure the transmitter and receiver antennas are angled as close to perfect face-to-face alignment as possible. Use
the LED panel on the Receiver to check the signal strength. Use a GPS handset to help achieve optimum alignment.
See the diagrams below.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 37
Mount the Transmitter and Receiver on poles to raise them above obstructions (as in B).
Figure 4a
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 38
When locating Shepherd-200M1 & 600M4 Transmitter and/or Receiver units on roof-tops, provide a clear line-of-sight
and avoid the possibility of signal multi-pathing by raising them on poles or locating them on the edge of the roofs
(as in B).
Figure 4b
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 39
The ground plane causes multi-pathing and can significantly affect distance.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 40
Figure 4c
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 41
4.2 System Assembly
The Shepherd-200M1 & 600M4 transmitter and receiver units are easy to install on both poles and walls using our universal
pole/wall mounting brackets.
Before Commencing Installation
1.
Verify proper operation of the camera and monitor/Recorder using cable before attempting to install the wireless link.
2.
Verify proper operation of the Shepherd-200M1 & 600M4 wireless link in a convenient location.
3.
Confirm that mounting poles and walls are strong enough to take the weight of the Shepherd-600M4 units.
Notice
To work with CCTV Camera Pros Shepherd-200M1 & 600M4, any installer or technician must have the following minimum
qualifications:
1.
A basic knowledge of CCTV systems and components.
2.
A basic knowledge of electrical wiring and low-voltage electrical hookups.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 42
3.
Have read this manual completely.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 43
Pole Mounting
Figure 4d
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 44
Wall Mounting
Figure 4e
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 45
1
ENCLOSURE
1pcs
2
BOLTS M8*18mm
4pcs
3
ROTATING BRACKET 100.5mmX65mmX52mm
1pcs
4
NUTS 1/4”
4pcs
5
SPRING WASHERS M6
4pcs
6
WASHERS
4pcs
7
MOUNTING BRACKET 120mmX120mmX50mm
1pcs
8
U-BOLTS 2 1/2”
2pcs
9
BASE COVER RUBBER SEAL
1pcs
10
BASE COVER
1pcs
11
BASE COVER SCREWS M3*8mm
7pcs
12
ANTENNA SCREWS M4*10mm
13
ANTENNA RUBBER SEAL
1pcs
14
ANTENNA
1pcs
15
WALL SCREWS
4pcs
16
WALL ANCHORS
4pcs
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
14pcs
User Guide | 46
4.3 Aligning the Transmitter and Receiver
Correct alignment of the antennas is critical for achieving optimum performance and transmission distance. The longer the
wireless video transmission range, the more important the alignment of the antennas becomes. For ranges of over one ½ mile,
correct alignment is measured in only a few degrees, both up and down, and left to right. Use the LED panel on the Receiver
to check the signal strength. Consider using a Global Positioning Satellite (GPS) handset to determine the Transmitter and
Receiver angles accurately (using a GPS system allows a 4 mile range to be aligned faster and more accurately than a ½ mile
range aligned “by eye”).
z
z
Connect the Cable Assembly units to the Transmitter and Receiver.
Connect the Transmitter cables to the CCTV camera and the Receiver cables to a monitor.
NOTE: When aligning the Transmitter and Receiver, hold the units in each position for at least 3
seconds before checking the resulting signal / picture, as the system requires a short time for
the processing and transmission of the digital signal.
NOTE: After alignment has been completed, tighten all bolts so that the units are secure and
will not move in a strong wind.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 47
To align antennas on the horizontal plane, carefully slacken the 2 bolts 2(a) attaching the Rotating Bracket to the Mounting
Bracket to allow horizontal movement. When correctly aligned, tighten the bolts.
Figure 4f
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 48
1.
To align antennas on the vertical plane, carefully slacken the 2 bolts 2(b) attaching the Rotating Bracket to the Enclosure
and tilt the antenna up or down. When correctly aligned, tighten the bolts.
Figure 4g
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 49
5. Trouble Shooting
1. NO PICTURE
z
z
z
z
z
z
z
2.
Check power is switched on for all units.
Check all connections are tight and secure.
Check the LED panel for signal strength.
Check alignment of the Transmitter and Receiver.
Verify proper operation of the camera and monitor using cable.
Verify proper operation of the Shepherd-200M1 & 600M4 wireless link in a convenient location.
Confirm the configuration settings for both the Transmitter and Receiver are the same and that no fields have been
left blank. Confirm Transmit Power is set at 5 (maximum).
PICTURE NOT CLEAR (This indicates a weak signal)
z
z
z
z
z
When testing for proper operation of the Shepherd-200M1 & 600M4 wireless link, if the Transmitter and Receiver are
very close together (30 feet or less), the system might suffer from signal saturation. Reduce the Signal Power in both
the TX and RX using the MagicLink software. For normal operation, set the Signal Power to 5 (maximum)
Check the LED panel for signal strength. Confirm Transmit Power is set to 5 (maximum)
Verify all connections are tight and secure.
Confirm there are no obstructions between the Transmitter and Receiver (see below).
Confirm there are no other possible causes of interference (see below).
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 50
z
z
z
z
z
Check the Transmitter and Receiver units are mounted at similar heights. There should be no more than a 10 foot
variance in height.
Check the alignment of the Transmitter and Receiver. (Note that if the bolts used for fixing the alignment are not
properly tightened, the units may blow out of alignment in strong winds).
Raise the height of the Transmitter and Receiver units.
Use MagicLink to increase the Range in both the Transmitter and Receiver units.
Move the Transmitter and Receiver closer together.
Possible obstructions and other causes of interference.
z
z
z
z
z
z
Water or anything with water in it, including people and other living things, snow, rain etc. can all reduce the
transmission distance.
Metals and anything containing metal—steel-reinforced concrete (rebar), metal window screens and tool-room cages,
aluminum siding and wall insulation foil, even metallic paints, metallic wallpapers and mirrors will affect the quality of
the signal.
Lead windows kill radio transmission, as do windows with a UV protective coating or metallic energy-saving film.
Other materials such as brick, drywall or wood, also cut down on the signal, depending on their water content.
High Voltage transmission lines may cause interference to the signal.
AC generators in close proximity to the Transmitter or Receiver may cause interference lines in the picture.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 51
3. PICTURE TOO DARK
z
Make sure that monitors and other peripheral equipment connected to the video source are set to high impedance
termination since the Transmitter has a built-in 75ohm termination.
4. PICTURE TOO BRIGHT
z
Make sure the Receiver video output line is terminated with 75ohm.
5. CANNOT CONTROL PTZ
z
z
Check the twisted-pair cables are connected correctly (see pages 11-14).
Check the RS485 PTZ settings in the Transmitter and Receiver are the same as on the PTZ Controller.
6. PTZ CONTROL IS NOT SMOOTH
z
z
Check the RS485 twisted-pair cables’ connections are good.
If the connection distance between the PTZ Controller and the Receiver is too long, reduce the baud rate on both the
PTZ Controller and on the Shepherd-200M1 & 600M4 Transmitter and Receiver.
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 52
6. Settings Record
Date (1)
Date (2)
Shepherd-200M1 & 600M4 / location
identification
Video System (PAL / NTSC)
Security Setup
Encrypt Method (AES / RC4)
Data Encrypt Key
Connection ID
PTZ RS485 Setup
Baud Rate
Data Bit
Parity
Stop Bit
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
User Guide | 53
Contact Information
CCTV Camera Pros
Phone: 888-849-2288
Fax: 888-849-2288
CCTV Camera Pros
Wireless Surveillance Camera Transmission System
www.cctvcamerapros.com
Email: sales@cctvcamerapros.com
User Guide | 54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising