Quick Reference Guide (Download PDF, 2.4M)

Quick Reference Guide (Download PDF, 2.4M)
2016 Infiniti Q50
Hybrid
Quick Reference Guide
2
4
3
1
6
9
10
Behind
steering wheel
16
Behind
5 steering wheel
7
8
11
12
18
17
17
19
20
15
21
13
21
14
22
23
VEHICLE INFORMATION DISPLAY
1 2 LOW TIRE PRESSURE WARNING LIGHT
HEADLIGHT AND TURN SIGNAL CONTROL
3 EV INDICATOR LIGHT*
4 PUSH-BUTTON IGNITION SWITCH
5 ASSIST CHARGE GAUGE
6 7 WIPER AND WASHER SWITCH
8 INTELLIGENT CRUISE CONTROL/CRUISE
CONTROL/DRIVER’S ASSISTANCE SWITCHES
9 STEERING WHEEL SWITCHES FOR
AUDIO*/BLUETOOTH®
10 INSTRUMENT BRIGHTNESS CONTROL*/
TRIP RESET SWITCH
11 VEHICLE INFORMATION DISPLAY SWITCHES
12 TILT AND TELESCOPIC STEERING COLUMN*
*See your Owner’s Manual for information.
13 VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH*
14 TRUNK RELEASE SWITCH
15 HOOD RELEASE*
16 UPPER DISPLAY
17 HEATER AND AIR CONDITIONER SWITCHES
18 LOWER DISPLAY
19 AUDIO SYSTEM
20 FRONT PASSENGER AIR BAG
STATUS LIGHT*
21 HEATED SEAT SWITCHES
22 INFINITI CONTROLLER
23 DRIVE MODE SWITCH*
table of contents
new system features
Approaching Vehicle Sound for Pedestrians (VSP) System . . . . . . . . . . . . . 2
Main Interface Switches Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
User Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator . . . . 4
Hybrid Awareness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Direct Response Hybrid™ System Warning Light . . . . . . . . . . . . . . . . . . . . . . 5
Loose Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fuel-filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Lower Display Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Driving Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Active Lane Control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Heated Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
first drive features
Infiniti InTouch™ Services (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .8
Infiniti Intelligent Key System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Around View® Monitor (AVM) with Moving Object Detection (MOD) . . . . . 11
Trunk Lid Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Automatic Drive Positioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Assist Charge Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Starting/Stopping the Hybrid System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Outside Mirror Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Heater and Air Conditioner (automatic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FM/AM/HD Radio®/SiriusXM® Satellite Radio . . . . . . . . . . . . . . . . . . . . . . 21
USB (Universal Serial Bus) Connection Port/iPod® Interface . . . . . . . . . . 22
Conventional (Fixed Speed) Cruise Control (if so equipped) . . . . . . . . . . . 22
Intelligent Cruise Control (ICC) (if so equipped) . . . . . . . . . . . . . . . . . . . . 23
system guide
Vehicle Information Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Infiniti InTouch™ Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
HomeLink® Universal Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Please see your Owner’s Manual for important safety information
and system operation limitations.
•A
cellular telephone should not be used for any purpose while
driving so full attention may be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
• Children 12 and under should always ride in the rear seat
properly secured in child restraints or seat belts according to their
age and weight.
• Do not drink and drive.
For more information, refer to your InTouch Owner’s Manual, the
“Safety –– Seats, seat belts and supplemental restraint system
(section 1)” and the “Starting and driving (section 5)” of your
Owner’s Manual.
Additional information about your vehicle is also available in your Owner’s
Manual, InTouch Owner’s Manual and at www.InfinitiUSA.com.
To view detailed
instructional videos, go to
www.infinitiownersinfo.mobi/2016/q50
or snap this barcode with an appropriate
barcode reader.
n ew sy s t em f e a t u r e s
Approaching Vehicle Sound for Pedestrians (VSP) System
The VSP system helps alert pedestrians to the presence of the vehicle when it is being
driven at a low-speed.
When the vehicle starts to move, it produces a sound. The sound stops when the vehicle
speed reaches approximately 19 mph (30 km/h) while accelerating.
This sound will activate again when decelerating to a speed of less than 16 mph (25 km/h).
For more information, refer to the “Hybrid System Overview (section Hybrid System)” section of your Owner’s Manual.
Main Interface Switches Overview
1 AUDIO – Press to display the main audio screen.
From here, all of the audio functions
can be accessed.
2 MENU – Press to display the main menu screen.
1
2
3
From here, there is access to the navigation
functions and all the applications, including the
Settings application.
3 CLIMATE – Press to display the “CLIMATE” screen. From here, you have access to climate
control, heated steering wheel and heated seat functions.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
User Registration
Driving positions, navigation, climate controls, etc.,
can be memorized for each user.
To register a new user:
1. Press the MENU button. The menu screen
will appear.
2. Touch the right arrow key until “Edit User” is
displayed. Then touch the “Edit User” key.
3. Touch the “User List” key.
4. Touch the “Add New” key. From here, you can edit Name and Icon.
5. Select the “OK” key when finished.
For more information, refer to the “Information and settings (section 8)” of your InTouch Owner’s Manual.
2
Upper Display
The upper display is controlled by the touch-screen,
Infiniti controller and the
switch on the
steering wheel.
Press the OK button 1 on the Infiniti controller
or the OK button on the steering wheel switch to
display the menu screen. From here, you are able to
choose from audio sources, map settings, handsfree phonebook and adding new options.
Use the dial on the Infiniti controller to move
the cursor and press the OK button 1 to select
an item.
3
1
2
While on the map screen, use the Infiniti controller
to navigate to another location on the map by sliding the controller in the direction you
would like to go.
Press the
button 2 to return to the previous page.
MAP AND DISPLAY VIEW
There are different variations of split screen views that can be displayed on the upper
display. The map is always displayed on the right-hand side of the screen. Some of the left
side options are turn list, intersection and turn-by-turn.
To customize the split screen views on the upper display:
1. When the current location map screen is displayed, press the MAP/VOICE button 3 on
the Infiniti controller and the display view bar will appear at the bottom of the screen.
2. T ouch an icon on the display view bar, or use the dial on the Infiniti controller to scroll
through the possible options and press the OK button 1 to select one.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
3
essent i al i n f o r m a t i o n
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Flat Tire Visit Dealer or Tire Pressure Low — Add Air warning message will appear in the
vehicle information display 1 and the low tire
pressure warning light 2 will illuminate when one
or more tires are low in pressure and air is needed.
• The tire pressures should be checked when
the tires are cold. The tires are considered cold
after the vehicle has been parked for 3 hours
or more or driven less than 1 mi (1.6 km) at
moderate speeds.
1
2
When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tire to the
recommended COLD tire pressure.
To use the Tire Inflation Indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the hybrid system.
3. Add air to the under-inflated tire, and within a few seconds, the hazard warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once and the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.
After tire pressures are adjusted, drive the vehicle at speeds above 16 mph (25 km/h). The
Flat Tire Visit Dealer or Tire Pressure Low — Add Air warning message and low tire pressure
warning light 2 will extinguish.
When the low tire pressure warning light 2 flashes for 1 minute and then remains on, the
TPMS is not functioning properly. Have the system checked. It is recommended that you
visit an INFINITI retailer for this service.
Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and
the outside temperature. Low outside temperature can lower the temperature of the air
inside the tire, which can cause a lower tire inflation pressure. This may cause the low tire
pressure warning light 2 to illuminate. If the warning light illuminates, check the tire
pressure in your tires.
• Check the tire pressure (including the spare tire) often and always prior to long
distance trips.
The Tire and Loading Information label contains valuable information. Please refer to
the “Technical and consumer information (section 10)” of your Owner’s Manual for the
location of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and Do-it-yourself (section 8)” of your Owner’s Manual.
4
Hybrid Awareness
Your vehicle is virtually silent in the electric mode. If you exit your vehicle while it is on but
the engine is not running, the engine will automatically start, informing you that the vehicle
is still on.
Do not store your Infiniti Intelligent Key within the detection range of the vehicle.
This may cause welcome lights and other functions to activate, creating unwanted
battery drain.
The hybrid system is designed for optimum efficiency and performance. Activation of the
electric mode may vary with driving conditions and driver input. A full battery display does
not indicate the vehicle should be in the electric mode.
The ready to drive
indicator light illuminates when the hybrid system is powered and
the vehicle may be driven.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Direct Response Hybrid™ System Warning Light
This light will illuminate when the ignition switch is in the ON position
and will extinguish when the hybrid system is started.
The light will also illuminate when a malfunction occurs in the electric
motor or hybrid system.
When this light illuminates while driving, immediately stop the vehicle
in a safe location and contact an INFINITI retailer.
If the hybrid system warning light blinks while driving, it may indicate that the Li-ion
battery charge is low and you cannot continue to drive.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the vehicle information display 1 when the fuelfiller cap is not tightened correctly.
1
To tighten, turn the cap clockwise until a single click
is heard.
The warning message will extinguish when
the vehicle detects the fuel-filler cap is properly
tightened and the
or
button 2 on the
steering wheel is pressed.
If the cap is not properly tightened, the Malfunction
Indicator Light
may illuminate.
2
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
5
essent i al i n f o r m a t i o n
Fuel-filler Door
The fuel-filler door is located on the rear
passenger’s side of the vehicle.
Ensure that at least the driver’s door is unlocked.
Push the left side of the fuel-filler door (in the
middle) to open.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
Lower Display Maintenance
Only use a microfiber cloth to clean the lower display.
For more information, refer to the “Appearance and care (section 7)” of your Owner’s Manual.
Driving Aids
The trip computer displays different driving aids,
including “Forward” Emergency Braking, “Lane”
Departure Prevention (if so equipped) and “Blind
Spot” Intervention® if they are currently activated.
To disable driving aids or warnings:
1. Press the MENU button 1 just below the
lower display.
2. T ouch the right arrow key until you see “Driver
Assistance”. Touch the “Driver Assistance” key.
3. Touch the key that corresponds with the driving
aid or warning you would like to turn off (“Forward
Assist”, “Lane Assist” or “Blind Spot Assist”).
4. Select the driving aid line key to disable.
1
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Active Lane Control (if so equipped)
Active Lane Control slightly corrects front tire angles and steering wheel torque, allowing
the driver to make fewer steering wheel corrections.
Active Lane Control is active when:
• The vehicle is driven at speeds of approximately 45 mph (70 km/h) and above.
• The Lane Departure Prevention and Active Lane Control systems are enabled in the
Settings menu.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
6
Heated Steering Wheel
The heated steering wheel system is designed to operate only when the surface
temperature of the steering wheel is below approximately 68°F (20°C). The steering wheel
heater will also turn off automatically after approximately 30 minutes.
To manually turn on the heated steering wheel, touch the steering wheel heater icon 1
within the “CLIMATE” screen in the lower display. The indicator light will illuminate.
AUTOMATIC STEERING WHEEL HEATER
When turned on, the steering wheel heater will
automatically heat the steering wheel whenever
the temperature inside the vehicle compartment
is below approximately 68°F (20°C) at the time of
pushing the ignition switch to the ON position. The
temperature of the steering wheel will also fluctuate
while turned on.
1
To turn on the automatic steering wheel heater:
1. Press the MENU button just below the
lower display.
2. Touch the “Settings” key.
3. Touch the right arrow key until you
see “Others”.
4. Touch the “Others” key.
5. Touch “Climate”.
6. Touch the “Auto Steering Wheel Heater” key 2 to turn it on.
2
For more information, refer to the “Heater and air conditioner (section 3)” of your InTouch Owner’s Manual.
Clock Set/Adjustment
To adjust the time and the appearance of the clock on the display:
1. Press the MENU button under the lower touch-screen display.
2. Touch the “Settings” key.
3. Locate and touch the “Clock” key.
The following settings can be adjusted:
On-Screen Clock: Set the clock display on or off.
When this item is on, the clock display appears.
Daylight Savings Time: The application of Daylight
Savings Time can be turned to on, off or Auto.
2
1
Clock Format (24h): The clock can be set to 12-hour or 24-hour format. When the indicator
light illuminates, the clock is set to the 24-hour format.
Time Zone: Adjust the time zone. Choose a time zone from the available list. Press the
button to return to the previous screen.
Offset Adjustment: The time can be adjusted forward or backward by minutes 1
and/or hours 2 . The current clock time can be set up for a difference of 12 hours and
59 minutes.
For more information, refer to the “Getting Started (section 2)” of your InTouch Owner’s Manual.
7
f i rst dr i v e f e a t u r e s
Infiniti InTouch™ Services1 (if so equipped)
Infiniti InTouch Services combine personalized convenience, concierge settings and personal
security features to compliment the Total Ownership Experience®. For more details on Infiniti
InTouch Services or to enroll your vehicle, please visit usa.infinitiintouch.com or
call 800-334-7858.
To access Infiniti InTouch Services:
1. Press the MENU button 1 on the control panel.
2. Select the “InTouch Services” key 2 on the display.
Available Infiniti InTouch services include:
3
Automatic Collision Notification – In case of air bag
deployment, a signal is sent containing the vehicle’s
location and customer information to notify the
proper authorities.
Emergency Call – This service provides emergency
assistance by connecting the subscriber to an
Infiniti InTouch Services Specialist.
• In case of an emergency, press the in-vehicle
telematics SOS button 4 .
•A
Response Specialist will provide assistance
based on the situation described by the
vehicle’s occupant.
Enhanced Roadside Assistance – Roadside
Assistance can be accessed by touching the “Infiniti
Connection” key 2 on the Info menu or the
key
3 on the map screen.
• This service allows subscribers to receive
assistance for a non-emergency incident, such as
towing, or a third party response.
My Schedule – Access your personal online Google
Calendar™, hear details read via text-to-speech2 and
select a location as a destination via the Infiniti InTouch Navigation.
2
1
4
Report Stolen Vehicle – A Response Specialist will attempt to obtain location
information from a reported stolen vehicle and provide that information to a local law
enforcement agency.
Remote Door Lock/Unlock – Remotely access your vehicle via an Infiniti InTouch Services
Response Specialist or the designated website to remotely lock or unlock your vehicle.
Remote Sound Horn and Flash Lights — Activate the vehicle’s headlights and horn via the
Infiniti InTouch Services web portal or companion app.
Remote Engine Start — If the vehicle is equipped with both TCU (Telematics Control Unit)
and Remote Start, remotely start the vehicle via the Infiniti InTouch Services web portal or
companion app.
8
Alarm Notification – This system will notify you when the factory-installed vehicle alarm
system has been activated.
Scheduled Maintenance Notification – Receive scheduled maintenance notifications
based on mileage data provided by your vehicle.
Maintenance Alert – Receive notification of a vehicle system malfunction that triggers
instrument panel warning lights.
Destination Assistance – Receive point-of-interest assistance via a guided IVR (Interactive
Voice Response) or a Response Specialist by pressing the
key 3 on the map screen or
the Infiniti InTouch Services web portal.
Destination Send-to-Vehicle – Find and download point-of-interest information from
Google Maps™ mapping service.
Connected Search – Select “Connected Search” from the Destination menu on the
vehicle’s Infiniti InTouch Navigation to conduct a point-of-interest search within a certain
distance of the vehicle’s location.
Drive Zone – Monitor the movement of your vehicle within a specified region. Set up
boundaries in the Monitoring section of the Infiniti InTouch Services web portal.
Max Speed Alert – Set a maximum speed on the Infiniti InTouch Services web portal. You
will receive notifications if your vehicle exceeds the maximum speed setting.
Mobile Information Service – Receive the latest news headlines, stock quotes and sports
scores by setting up preferences on the Mobile Information Service page in the Infiniti
InTouch Services web portal.
Valet Alert – Use to set up a 0.2-mile radius around your vehicle.
• Activate alerts by pressing the “Connect to Voice Menu” key on the Infiniti InTouch
Services screen or by pressing the
key 3 on the map screen.
•A
t the prompt, say “Valet Alert” and then “Activate” or “Deactivate”.
1
riving is serious business. Only use services when safe to do so. Services, including automatic crash notification and
D
SOS, require an active subscription, and are dependent upon the telematics device being in an operative condition, its
ability to connect to a wireless network, compatible wireless network availability, navigation map data, and GPS satellite
signal receptions, the absence of which can limit or prevent the ability to reach Customer Care or receive support. AT&T
has announced that on December 31, 2016, AT&T will discontinue 2G network service. Vehicles equipped with telematics
hardware compatible for use with the 2G GSM/GPRS cellular network provided by AT&T will be unable to connect to the 2G
network and unable to access the Infiniti InTouch Services features. You must enroll by June 30, 2016 to access the services
on the 2G network through December 31, 2016. Services require compatible cellular network provided by AT&T. Cellular
network and GPS signal not available in all areas and/or available at all times. Technology is evolving, and changes to cellular
networks provided by independent companies are not within Infiniti’s or Sirius XM Connected Vehicle Service’s (“Sirius XM”)
control. Like other devices that rely on network coverage, once the network service is discontinued, Infiniti InTouch services
will not function unless equipment replacements, upgrades, or alternative network coverage are available at that time,
which neither Infiniti nor Sirius XM can guarantee. Infiniti and Sirius XM are not responsible for associated costs that may
be required for continued operation due to cellular network turndown or discontinuation (including equipment upgrades, if
available, or roaming charges on alternative networks). Certain vehicle services and features, including Google® compatible
services, provided by independent companies are not within Infiniti’s or Sirius XM’s control and are subject to change
without notice or liability to Infiniti or Sirius XM and either of their affiliates and agents. Text rates and/or data usage may
apply. Certain services require a PIN for activation. See www.infinitiusa.com/Intouch for more information. App availability
is dependent upon vehicle model, trim level, packaging, and/or options. See www.infinitiusa.com/Intouch/system-details
for complete app availability details. Some apps require the Infiniti InTouch companion app installed and logged in with an
active account to function. Never program while driving. GPS mapping may not be detailed in all areas or reflect current road
status. Compatible smartphone required. Processing speed may vary. May require retailer service visit or software upgrade to
activate. Terms and conditions of subscription agreement apply.
2
Laws in some communities may restrict the use of text-to-speech. Check local regulations before using this feature.
For more information, refer to the “Viewing technical information (section 7)” of your InTouch Owner’s Manual.
9
f i rst dr i v e f e a t u r e s
Infiniti Intelligent Key System
The Infiniti Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the hybrid
system. It is important to make sure the Intelligent Key
is with you (that is, in your pocket or purse).
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
1
2
LOCKING AND UNLOCKING DOORS
Using the Intelligent Key:
• Touch the inside of the door handle 1 to unlock
the corresponding front door.
•P
ressing the request switch 2 while touching the
inside of the door handle will unlock the rest of
the doors.
• T o lock the vehicle, push either door handle
request switch 3 once.
•C
hange vehicle settings to unlock all doors by touching
the inside of the door handle 1 . For more information, refer
to the “Information and settings (section 8)” of your InTouch
Owner’s Manual.
8
Using the key fob:
5
• Press the
button 5 on the key fob to unlock the driver’s door.
6
•P
ress the
button 5 again; all other doors will unlock.
• Press the
button 4 on the key fob to lock the doors.
3
4
7
To release the trunk lid, press the
button 6 for more than
1 second. Lift the trunk lid to access the trunk.
The Intelligent Key can also be used to activate the panic alarm by pressing and holding
the button 7 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
REMOTE ENGINE START*
The remote engine start system must be enabled in the vehicle settings within the
lower display.
The remote engine start operating range is approximately 197 ft (60 m) from the vehicle.
The effective operating range may be shorter due to environmental conditions or obstacles
between you and the vehicle.
For the remote engine start to function, the vehicle must be in the P (PARK) position with
the ignition off and all the doors closed and locked.
*Laws in some communities may restrict the use of remote starters. Check local regulations before using this feature.
10
To start your vehicle remotely:
1. Press the
2. Within 5 seconds, press and hold the remote engine start button 8 for
at least 2 seconds.
button 4 .
The engine will start, and the parking lights will turn on.
The automatic climate control system will automatically adjust the passenger compartment
to the appropriate set temperature when the Remote Engine Start feature is used.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10-minute period.
• After two remote starts, the ignition switch must be cycled before the remote start can be
used again.
To start driving, depress the brake pedal and push the ignition switch START/STOP button.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is discharged
or environmental conditions interfere with the
Intelligent Key operation, start the hybrid system
according to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key,
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch START/STOP
button while depressing the brake pedal and the hybrid system will start.
For more information, refer to the “Instruments and controls (section 2)”, the “Pre-driving checks and adjustments (section 3)”,
the “Starting and driving (section 5)” and the “Maintenance and Do-it-yourself (section 8)” of your Owner’s Manual.
Around View® Monitor (AVM) with Moving Object Detection (MOD)
With the ignition switch in the ON position, the Around View Monitor is activated by
pressing the CAMERA button 1 , located on the
control panel, or by moving the shift lever to the
R (REVERSE) position. The control panel displays
various views of the position of the vehicle.
When the shift lever is in the P (PARK), N (NEUTRAL)
or D (DRIVE) position and the CAMERA button 1 is
pressed, the following views will display in order:
1
11
f i rst dr i v e f e a t u r e s
Start from any Control Panel screen
Front view and bird’s-eye view
Press
Press
Press
Front wide view
Front view and front-side view
Press
When the shift lever is in the R (REVERSE) position and the CAMERA button 1 is pressed,
the following views will display in order:
Rear view and bird’s-eye view
Rear view and front-side view
Press
Rear wide view
Press
Press
The colored guide lines on the display screen indicate vehicle
width and approximate distances to objects with
reference to the vehicle body line.
2
• Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft
(2 m) and 10 ft (3 m)
There are some areas where the system will not
show objects.
12
• When in the front or the rear view display, an
object below the bumper or on the ground may
not be viewed 2 .
3
• When in the bird’s-eye view, a tall object near the seam of the camera viewing areas 3
will not appear in the monitor.
The distance between objects viewed on the Around View Monitor differs from the
actual distance.
Objects in the bird’s-eye view will appear further than the actual distance.
MOVING OBJECT DETECTION (MOD)
If the MOD system detects moving objects surrounding the vehicle, a yellow frame 4 will
be displayed on the camera image and a chime will sound.
In the bird’s-eye view, a yellow frame is displayed on those camera images (front, rear,
right, left) where moving objects are detected.
When the following are displayed:
• Blue MOD icon 5 ; the system is operative in
this view.
• Gray MOD icon 6 ; the system is not operative in
this view.
• No MOD icon; the system is off.
6
5
4
7
To temporarily turn the system on or off, touch the
Sonar-MOD key 7 .
For more information, refer to the “Monitor system (section 7)” of your InTouch Owner’s Manual.
Trunk Lid Release
Using the Intelligent Key while it is in your pocket or purse:
• Push the trunk open request switch 1 for
more than 1 second while carrying the Infiniti
Intelligent Key with you.
1
Using the key fob:
• Press the trunk HOLD button 2 on the Intelligent
Key for more than 1 second.
•P
ush the trunk open request switch 1 while all of the doors
are unlocked.
Using the trunk lid release switch 3 on the instrument panel:
• F rom inside the vehicle, push down on the trunk lid release switch
3 on the instrument panel.
To completely disable all power to the trunk lid, push the trunk
release power cancel switch 4 located in the glove box to the OFF
position. While in this position, the trunk lid cannot be opened
with the trunk open request switch 1 , trunk HOLD
button 2 on the key fob or the trunk lid release
switch 3 .
2
3
4
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
13
f i rst dr i v e f e a t u r e s
Seat Adjustments
POWER SEAT ADJUSTMENTS
To slide the seat forward or backward, push the
switch 1 forward or backward.
To recline the seatback, push the
forward or backward.
3
1
switch 2
2
SEAT LIFTER
To adjust the angle of the front portion or height of the seat, push the front or rear end of
the
switch 1 up or down.
POWER LUMBAR SUPPORT (if so equipped)
To adjust the seat lumbar support, push the front or back end of the
switch 3 .
For more information, refer to the “Safety – Seats, seat belts and supplemental restraint system (section 1)” of your
Owner’s Manual.
Heated Seats
There are two ways to operate the heated seats:
1. Push the heated seat switch 1 .
2
2
• Every
press of the switch allows you to cycle
through the five different modes of
“AUTO” – “High” – “Mid” – “Low” – “OFF”.
3
2. W
hile on the “CLIMATE” screen on the lower
display, touch the left or right heated seat
icon 2 .
• T he “Left Heater Settings” or “Right Heater
Settings” screen is displayed with a list of the
five different modes of “AUTO” – “High” –
“Mid” – “Low” – “OFF” to choose from.
1
1
• T he indicator light on the heated seat switch 1 will illuminate when the system is in
“AUTO” – “High” – “Mid” – “Low”.
•W
hile in “AUTO”, the heated seats will turn on and off automatically depending on
temperature conditions in the vehicle compartment.
• T o view which of the five modes the system is in, press the CLIMATE button 3 .
This will bring up the “CLIMATE” screen on the lower display. From here, you will
see the right or left heated seat icon 2 , and below the icon is the mode the system
is in currently.
For more information, refer to the “Heater and air conditioner (section 3)” of your InTouch Owner’s Manual.
14
Automatic Drive Positioner
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.
Follow this procedure to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the
adjusting switches for each feature.
• Push the SET switch, and within 5 seconds, push the memory switch (1 or 2) for at
least 1 second.
• The indicator light on the memory switch you select will illuminate for approximately
5 seconds and a buzzer will sound.
• The driver’s seat, steering column and outside mirror positions are now set to
your preferences.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Assist Charge Gauge
This shows the power consumed 2 or generated
1 by the electric motor.
1
2
For more information, refer to the “Hybrid System Overview (section
Hybrid System)” and the “Instruments and controls (section 2)” of your
Owner’s Manual.
Starting/Stopping the Hybrid System
It is important to make sure the Infiniti Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP button to
start the hybrid system.
TURNING THE HYBRID SYSTEM OFF
Move the shift lever to the P (PARK) position and apply the parking brake.
Press the ignition switch START/STOP button to turn the hybrid system off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
15
f i rst dr i v e f e a t u r e s
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch 1 right or left.
1
2
Adjust each mirror to the desired position using
the switch 2 .
REVERSE TILT-DOWN FEATURE
The reverse tilt-down feature will turn both outside mirror surfaces downward to provide
better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the R (REVERSE) position.
3. Choose the right or left outside mirror by operating the outside mirror control switch.
4. The outside mirror surfaces will move downward.
Both outside mirror surfaces will return to their original positions when one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) position.
• The ignition switch is placed in the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 1 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the
position 2 to
turn on the headlights.
3
1
2
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it is dark and off when
it is light. The system will keep the headlights on for a period of time after you turn the
ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to the AUTO position 3
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF position,
position 1 or
position 2 .
16
HIGH BEAM SELECT
To manually select the high beam function:
1. Turn the headlight control switch to the
2. Push the headlight control switch forward
4 to select the high beam function. The
blue indicator light
will illuminate in the
instrument panel. Pull the headlight switch back
to the original position to select the low beam.
The blue indicator light will extinguish.
position 2 .
4
5
Pull and release the headlight control switch 5 to flash the headlight high beams on
and off.
HIGH BEAM ASSIST (if so equipped)
The High Beam Assist system will operate when the vehicle is driven at approximately
22 mph (35 km/h) and above. If an oncoming vehicle or leading vehicle appears in front
of your vehicle when the high beam is on, the headlights will automatically be switched to
the low beam.
Following the procedure below only activates the High Beam Assist system. This does not
necessarily turn on the high beam even if there is no other traffic. Both ambient light and
traffic conditions have to be correct for the high beam to illuminate.
To activate High Beam Assist, turn the headlight control switch to the AUTO position 3
and push the headlight control switch forward 4 to turn on the high beam. The High
Beam Assist indicator light
will illuminate.
FOG LIGHT SWITCH
The headlights must be on and the low beams
selected for the fog lights to operate.
Turn the switch (inside collar) to the
to turn the fog lights on.
position 6
Turn the switch (inside collar) to the OFF position to
turn the fog lights off.
6
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to flash but the lever does not latch
to signal a lane change. Hold the lever until the lane change is completed.
Move the lever up or down until the turn signal begins to flash but the lever does not latch
and release the lever. The turn signal will automatically flash three times.
Choose the appropriate method to signal a lane change based on road and traffic conditions.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
17
f i rst dr i v e f e a t u r e s
Wiper and Washer Switch
RAIN-SENSING AUTO WIPER SYSTEM (if so equipped)
Move the lever to one of the following positions to
operate the windshield wipers:
1 Mist (MIST) – One sweep operation of
2 Auto (AUTO) – Operates the rain-sensing wipers
MIST 1
3
OFF
AUTO 2
LO 4
the wipers.
HI 5
intermittently. The intermittent speed can be
adjusted by twisting the time control ring 3 to
increase or decrease wiper sensitivity.
4 Low (LO) – Wipers operate at a continuous
low-speed.
6
5 High (HI) – Wipers operate at a continuous
6 Pull the lever toward you to activate the washer. The wipers will operate several times.
high-speed.
PULLING UP THE WIPER ARM
The wiper arm should be in the up position when
replacing the wiper.
To pull up the wiper arm, push the wiper switch
to the MIST 1 position twice within 1 minute of
placing the ignition switch in the OFF position. The
wiper operation stops in mid-operation and the
wiper arm can be pulled up.
The shift lever should be in the P (PARK) position.
To return the wiper arm, place the wiper arm in the down position and operate the wiper
switch once.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
18
6
3
2
4
8
5
11
10
4
9
7
12
6
1
13
Heater and Air Conditioner (automatic)
1 CLIMATE BUTTON
Press to display the “CLIMATE” screen on the lower display.
2 DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS
Press the driver’s side temperature control buttons up for warmer air or down
for cooler air.
3 PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS
To manually adjust the passenger’s side temperature, press the passenger’s side
temperature control buttons up for warmer air or down for cooler air.
4 FAN SPEED CONTROL BUTTONS
To manually adjust the fan speed, press the
button or touch the
key to increase
the fan speed. Press the button or touch the
key to decrease the fan speed.
5 AUTO BUTTON
Press the AUTO button to turn the system on, and the system will automatically control
the inside temperature (automatic cooling and/or dehumidified heating), air flow
distribution and fan speed.
6 MODE CONTROL BUTTON
Press the
button or touch the
key in the center of the lower display to cycle
through the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the front defroster and foot vents.
19
f i rst dr i v e f e a t u r e s
7 AUTO AIR RECIRCULATION KEY (if so equipped)
Touch to allow inside air recirculation and outside air circulation to switch automatically
depending on the quality of the outside air.
8 INTAKE AIR CONTROL BUTTON
Pressing the intake air control button
will cancel auto air recirculation 7 (if so
equipped) until it is re-activated from the touch-screen (see above). Press the intake
air control button
to manually control whether the interior air is recirculated
or outside air is drawn into the vehicle. When the indicator light is on, interior air is
recirculated, outside odors are avoided and the interior vehicle temperature is most
effectively maintained.
The air recirculation mode cannot be activated when the climate control system is in the
front defroster mode
or the front defroster and foot vent mode .
9 A/C KEY
Touch the “A/C” key to turn the air conditioner system on or off. This system helps cool
and dehumidify the air inside the cabin and defog the windows.
10 DUAL KEY
Touch to turn the passenger’s side temperature controls on or off. When the system
is on, the indicator light will illuminate. This function will allow the passenger’s side
temperature to be adjusted independently from the driver’s side by pressing the
passenger’s side temperature control buttons 3 .
11 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the front defroster button
to turn the system on. The A/C automatically
turns on when the front defroster mode is selected. This feature removes humidity from
the air.
To defrost the front and side windows, set the driver’s side temperature controls 2
and fan speed controls 4 to their maximum settings.
12 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS
Push the rear window and outside mirror defroster switch
or off.
This function automatically turns off after approximately 15 minutes.
to turn the system on
13 ON/OFF BUTTON
Press the ON/OFF button to turn the climate control system on or off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual and the “Heater and air
conditioner (section 3)” of your InTouch Owner’s Manual.
20
7
8
8
1
2
3
5
6
4
FM/AM/HD Radio®/SiriusXM®* Satellite Radio
1 AUDIO BUTTON
Press to display the “AUDIO” screen on the lower display.
(power) BUTTON/VOL (volume) CONTROL KNOB
Press the (power) button to turn the system on or off.
Turn the VOL (volume) control knob right or left to increase or decrease the volume.
SEEK•CAT/TRACK BUTTON
To scan quickly through each broadcasting station, press the SEEK•CAT/TRACK button
to stop at the previous or next broadcast station.
For satellite radio, press the SEEK•CAT/TRACK button to switch to the first channel of
the previous or next category.
For HD Radio®, press the SEEK•CAT/TRACK button to change the station.
Press the SEEK•CAT/TRACK button to change tracks on a CD.
Press and hold the SEEK•CAT/TRACK button to rewind or fast forward a track on a CD.
TUNE•CH/FOLDER BUTTON
To manually tune the radio, press the TUNE•CH/FOLDER button left or right.
Press and hold the TUNE•CH/FOLDER button left or right to accelerate radio tuning.
RADIO BUTTON
Press to select the radio band in the order of AM, FM and satellite radio.
DISC•AUX BUTTON
Press to change the audio source (CD, iPod®, USB, Bluetooth® Streaming Audio or AUX).
STATION PRESET KEYS
Up to 36 stations/channels can be set for AM, FM and satellite radio.
To store a station in a preset, you must first select a radio band by pressing the RADIO
button then tune to the desired AM, FM or satellite radio station.
Now select and hold the desired station memory key (1-36) until the preset number is
updated on the display and a beep is heard. Programing is now complete.
To retrieve a previously set station, press the right or left arrow 8 and touch the
memory key (1-36) that contains the stored station/channel you wish to listen to.
2 3
4
5
6
7
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional satellite radio subscription service.
For more information, refer to the “Audio system (section 4)” of your InTouch Owner’s Manual.
21
f i rst dr i v e f e a t u r e s
USB (Universal Serial Bus) Connection Port/iPod® Interface
The USB port 1 is located in the center console
under the armrest.
When a compatible USB memory device or iPod® is
plugged into the USB port:
2
1
•A
confirmation message appears. Select “Yes”
if you prefer to use the devices with Voice
Recognition in which song titles and artist names are registered in the system.
•C
ompatible audio files stored on the device can be played through the vehicle’s audio
system and front display.
If two USB devices are plugged in at the same time, you are able to use Voice Recognition
to choose which one should play. Just press the
button on the steering wheel to activate
Voice Recognition and follow the voice prompts.
This vehicle is equipped with audio and video RCA inputs 2 . This will allow you to play
audio and video through your vehicle from an external source.
For more information, refer to the “Getting Started (section 2)”, the “Audio system (section 4)” and the “Voice recognition
(section 10)” of your InTouch Owner’s Manual.
Conventional (Fixed Speed) Cruise Control (if so equipped)
The cruise control system enables you to set a constant cruising speed once the vehicle
has reached 25 mph (40 km/h).
The system will automatically maintain the set speed until you tap the brake pedal,
accelerate, cancel or turn the system off.
To activate the cruise control, push the ON/OFF switch on the steering wheel. The CRUISE
indicator light in the instrument panel will illuminate.
To set a cruising speed, accelerate the vehicle to the desired speed, push the SET –
switch on the steering wheel and release. The CRUISE SET indicator light in the instrument
panel will illuminate. Take your foot off the accelerator pedal. Your vehicle will maintain
the set speed.
To reset at a faster cruising speed, push and hold the RES + switch on the steering wheel.
When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the SET – switch on the steering wheel.
Release the switch when the vehicle slows to the desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch on the
steering wheel.
To turn off cruise control, push the ON/OFF switch on the steering wheel. The CRUISE
indicator light and the CRUISE SET indicator light in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
22
Intelligent Cruise Control (ICC) (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
4
To set vehicle-to-vehicle distance control mode,
press the
button 1 on the steering wheel for
less than 1.5 seconds. The gray
indicator light
2 will illuminate.
7
8
3
1
Accelerate to the desired speed.
Push down on the SET – switch 3 on the
steering wheel and release it. ICC will be set to the
desired speed.
2
Press the distance button 4 on the steering wheel
repeatedly to change the set distance between long,
middle and short.
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate 5 in set mode.
When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate 6 in
set mode.
5
6
To reset at a faster cruising speed, push up and
hold the RES + switch 7 on the steering wheel.
When the vehicle attains the desired speed, release
the switch.
To reset at a slower cruising speed, push down and hold the SET – switch 3 on the
steering wheel. Release the switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch 8 on the steering wheel. The set
vehicle speed indicator 5 will change to gray.
To turn off ICC, press the
button 1 on the steering wheel. The
the instrument panel will extinguish.
indicator light 2 in
To set conventional (fixed speed) cruise control mode:
While ICC is off, press the
than 1.5 seconds. The gray
button 1 on the steering wheel and hold it down for more
indicator light will illuminate.
Accelerate to the desired speed.
Push down on the SET – switch 3 on the steering wheel and release it. The green
indicator light will illuminate. Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
23
syste m g ui d e
Vehicle Information Display
When the
or
button 1 on the steering
1
wheel is pressed, the following modes will appear
on the vehicle information display 2 :
• F uel Economy – Displays the current
fuel consumption.
2
• A
verage Speed – Displays the average vehicle
speed since the last reset.
• D
istance/Time – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
• Range – Displays the estimated distance
3
to empty (dte) the vehicle can be driven
before refueling.
• N
avigation (if so equipped) – Displays the navigation route information when route
guidance is set in the Infiniti InTouch Navigation.
• Audio – Displays the status of the audio information.
• Driving Aids (if so equipped) – Displays driving aid status.
• Tire Pressure (if so equipped) – Displays the current tire pressure in each tire.
• Chassis Control – Displays the status of Active Lane Control and Active Trace Control.
• E nergy Flow – Displays the energy flow between the engine and the Li-ion battery and the
current charge level of the battery.
• EV Odometer – Displays the total distance traveled using the electric motor only.
• Acceleration Guide – Displays how efficiently the vehicle is being driven based on the
accelerator pedal position.
• Coolant Temp – Displays the current temperature of the coolant.
• Warning – Displays when a warning is present.
Push the TRIP RESET switch 3 for approximately 1 second to reset the currently
displayed trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Bluetooth® Hands-free Phone System
A cellular telephone should not be used
while driving so full attention may be given to
vehicle operation.*
SYSTEM OPERATING TIPS
Bluetooth® Controls
If the Voice Recognition system does not recognize
your voice commands:
1. Be sure to wait for the tone/beep before speaking
a command.
2. Reduce background noise as much as possible by
closing the windows and moonroof.
*Some jurisdictions prohibit the use of cellular telephones while driving.
24
Microphone
3. Make sure there are no other conversations in the car at the same time.
4. Lower HVAC blower fan speed and point vents away from the ceiling microphone.
5. Speak naturally. Speaking too fast, too slow, too soft, or too loud makes voice
recognition more difficult.
6. Confirm that the correct voice commands are being used. Glance at the screen to see the
currently available commands.
Press the
button on the steering wheel to activate Voice Recognition.
Press the button on the steering wheel to interrupt the voice prompts at any time and
speak a command after the tone.
To use the system faster, you may speak the second level commands with the main menu
command on the main menu.
To decrease or increase the volume of the voice prompts, push the volume control
switches or on the steering wheel or turn the (power) button/ VOL (volume) control
knob on the audio system while the system is responding.
The Voice Recognition system allows you to choose between voice input and manual
controls of lists. Choose the method that is easiest for you. For example, when a list is
shown, you can use the
switch and press the OK button on the steering wheel to
select an item from the displayed list instead of saying the item.
When using the
feature to navigate lists during Voice Recognition, use the spoken
menu readout feature to help navigate the list easily. Voice input is paused when menu
control is activated. To resume Voice Recognition, select a menu item by pushing the
switch or simply press the button on the steering wheel.
Reduce background noise as much as possible by closing windows and pointing HVAC
vents away from the ceiling.
After the tone, speak naturally without long pauses and without raising your voice.
When speaking phonebook names, use the full name (e.g., Michael Smith) or first
name (e.g., Michael).
To cancel a Voice Recognition session, say “Exit” or press and hold the
steering wheel for 5 seconds.
button on the
To go back to the previous command, say “Go Back”.
For more detailed information and instructions, refer to your cellular phone’s Owner’s
Manual and visit www.InfinitiUSA.com/bluetooth.
CONNECTING PROCEDURE
The vehicle must be stationary when connecting
the cellular phone.
1.Press the MENU button below the lower display and
touch the “Settings” key.
2. Touch “Bluetooth”.
3.Touch “Connect Device” and then touch “Add New”.
4. Initiate connecting from the cellular phone.
25
syste m g ui d e
• The connecting procedure varies according
to each cellular phone model. For detailed
connecting instructions and a list of
compatible cellular phones, please visit
www.InfinitiUSA.com/bluetooth.
• When prompted for a PIN, enter the PIN that
appears on the screen into the handset.
5. When connecting is complete, the screen will return
to the previous screen.
Some cellular phones may require you to accept
certain permissions in order to enable features on
your Bluetooth® system. During the Bluetooth®
pairing process, please check your cellular phone’s
display for pop-ups with the following request:
•M
essage Access — Granting Message Access
permission will enable text messaging
features on your vehicle’s Bluetooth® system. A
pop-up may display on your cellular phone stating
that the Bluetooth® system would like to access
your messages. Please select “ALLOW” 1 or
“YES” to grant this permission. If your cellular
phone presents an option to “Don’t show this
message again”, please make sure that this item
is checked.
Additionally, some popular devices will require
you to enable Notifications in order to receive text
messages through your vehicle. In your Bluetooth®
menu, select the Information icon 2 next to the
name of your vehicle’s Bluetooth® system. Ensure
that “Show Notifications” 3 is enabled on this
screen. A vehicle ignition cycle may be required for
changes to take effect.
PHONEBOOK SETUP
Depending on your cellular phone, the system may
automatically download your cellular phone’s entire
phonebook to the vehicle’s Bluetooth® system.
If the phonebook does not download
automatically, the vehicle’s phonebook may be
set up for manual entry.
To manually download entries:
1. Press the MENU button below the lower display.
2. Touch the “Settings” key.
3. Touch the “Phone/Mail” key.
26
1
3
2
4. Touch the “Phone Settings” key.
5. Touch the “Phonebook/Favorites Settings” key.
6. Touch the “Configure Phonebook Settings” key.
7.Touch the “Manual Phonebook Transfer” key.
• From here, you are able to transfer information
from your cellular phone to your vehicle.
MAKING A CALL FROM THE PHONEBOOK
1. Press the
button on the steering wheel.
2. After waiting for the tone, say “Phone”.
3. After waiting for the tone, say “Call”.
4.After the next tone, speak the name of a phonebook entry. For example, “Michael Smith”.
In some cases, names stored using all UPPERCASE letters may not be recognized by the
Voice Recognition system.
MAKING A CALL BY PHONE NUMBER
1.Press the
button on the steering wheel. A tone will sound.
2. After waiting for the tone, say “Phone”.
3.After waiting for the tone, say “Dial”.
4.Say the number you wish to call starting with the
area code in single digit format.
5.When you have finished speaking the phone
number, the system repeats it back and announces
the available commands.
6. Say “Dial”. The system acknowledges the command
and makes the call.
RECEIVING/ENDING A CALL
To accept the call, press the button on the
steering wheel or touch the “Answer” key.
To reject the call, touch the “Decline” key.
To hang up, press the button on the steering
wheel or touch the “Hang Up” key.
For more information, refer to the “Hands-Free Phone (section 5)” and the
“Voice recognition (section 10)” of your InTouch Owner’s Manual or please visit www.InfinitiUSA.com/bluetooth.
27
syste m g ui d e
Infiniti InTouch™ Navigation
Your Infiniti InTouch Navigation system can calculate a route from your current location
to a preferred destination. The real-time map display and turn-by-turn voice guidance will
lead you along the route.
The Infiniti InTouch Navigation system will continually update your vehicle’s position.
If you have deviated from the original route, it will recalculate the route from your
current location.
1
SYSTEM OPERATION
Move through the menus and on-screen keys by
rotating the Infiniti controller 1 to highlight an
item on the screen and pressing the OK button 2
to select the highlighted item, or touch the desired
key on the touch-screen display.
Press the
button 3 to return to the previous
screen. In a settings screen, this button can also
be used to apply the setting. In a character input
screen, this button can also delete the characters
that have been entered.
4
3
5
2
6
Press the MAP/VOICE button 4 to display the map.
Press and hold the CAMERA/
button 5 to
switch between the day screen (bright) and the
night screen (dark).
Upper Display 6 – Displays the map and can be
controlled by the Infiniti controller 1 .
9
7
Lower Display 7 – Displays navigation functions
and is not controlled by the Infiniti controller 1 .
Press the MENU button 8 below the lower display
to access the navigation functions.
SETTING A ROUTE
To set a route, first ensure that the correct region is
selected on the touch-screen.
1.Press the MENU button 8 below the
lower display.
8
2. Touch the “Destination” key 9 .
3. Check the State/Province to make sure it is correct. The default is the current location.
4. Enter the House Number and touch the “OK” key.
5. Enter the Street Name and touch the “List” key.
6. Select preferred Street/City combination*.
7. Touch the “Start” key.
* If the Street/City list is too long, press the
“List” key again.
28
button 3 and touch the “City” key. Then enter the city name, and touch the
CANCELING A ROUTE
1.Press the MENU button 8 below the lower display.
2. Touch the “Cancel Route” key 10 .
10
ZOOMING IN AND OUT
On the map screen, turn the Infiniti controller 1
right or left to zoom in or out.
MOVING AROUND THE MAP
To scroll the map, slide the Infiniti controller 1 in the direction you want to scroll.
CHANGING THE MAP VIEW
It is possible to switch between different map views: 2D and bird’s-eye view (3D).
To switch to the preferred map view:
1.Press the MENU button 8 below the
lower display.
2. Touch the “Settings” key 11 .
3. Touch the “Navigation” key 12 .
4. Touch the “Map Preferences” key.
5. Touch the “Map View” key.
6. From the “Map View” screen, you can choose
North Up (2D), Heading Up (2D) or Birdview (3D)
map views.
VOICE GUIDANCE
11
12
To activate voice guidance:
1.Press the MENU button 8 below the
lower display.
2. Touch the “Settings” key 11 .
3. Touch the “Navigation” key 12 .
4. Touch the “Guidance Preferences” key.
5. Touch the “Voice Guidance” key to toggle voice guidance on or off.
To adjust the guidance volume, select the “Guidance Volume” key.
To hear the current guidance during a programed route, press and hold the MAP/VOICE
button 4 next to the Infiniti controller 1 .
For more information, refer to your InTouch Owner’s Manual.
29
system g ui d e
HOMELINK
HomeLink® Universal Transceiver
The HomeLink® Universal Transceiver can learn and consolidate the functions of up to
three different hand-held transmitters, operating items such as garage doors, property
gates, outdoor and indoor lights or alarm systems.
To program the HomeLink® Universal Transceiver:
•P
osition the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the HomeLink indicator light in view.
•P
ress and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the HomeLink button and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the HomeLink button
will activate your device.
•A blinking light that turns to a solid, continuous light after 2 seconds indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink button, press and
release the learn or smart button (the name may vary by manufacturer, but it is usually
located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous two steps up to three times to complete the
programing process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
30
me mo
memo
me mo
Helpful Resources
Below is a list of helpful resources that can be used to learn more about the vehicle’s systems
and feature operations.
•Owner Portal
• Vehicle Owner’s Manual
1-855-444-7244
•Infiniti Client Support
Printing: January 2016 (03) / QR16EA HV37U0 / Printed in USA
1-800-662-6200
Support is always available if your Infiniti retailer
cannot assist you or you would like to provide
Infiniti directly with comments or questions.
www.owners.InfinitiUSA.com/iowners
Your Infiniti Owner Portal account contains
your personal preferences, vehicle information
and links to key vehicle features and services.
•Infiniti Roadside Assistance
•Infiniti InTouch™
•Infiniti Elite® Extended Protection Program
•SiriusXM
1-800-662-6200 (option 1)
As part of the Infiniti Total Ownership
Experience®, Roadside Assistance is
available to you, 24 hours a day 365 days a
year, for emergency roadside assistance.
1-800-662-6200
Infiniti Elite® Assurance Products provide
you with quality long-term protection
and enhanced peace of mind.
•Infiniti Financial Services Client Support
1-800-627-4437
For client support with your Infiniti
Financial Services loan or lease.
•Infiniti Financial Services
1-800-334-7858
usa.infinitiintouch.com
The suite of digital alerts and remote services is
your direct link to personal security,
convenience and confidence.
1-888-601-6296
For support with your SiriusXM subscription.
•Infiniti USA.com
www.InfinitiUSA.com/bluetooth
Reference this site for a list of compatible
cellular phones and instructions on how to
pair your cellular phone to your vehicle.
•Infiniti Electronic Quick Reference Guide
(use Quick Response (QR) code or URL below)
www.infinitifinance.com
Use the IFS Online Account Manager to check
your account status, schedule recurring
payments and access important forms.
To view detailed instructional videos, go to
www.infinitiownersinfo.mobi/2016/q50
or snap this barcode with an appropriate
barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features of your new vehicle.
Please see your Owner’s Manual for important safety information and system operation limitations. Features and
equipment in your vehicle may vary depending on model, trim level, options selected, order, date of production,
region or availability. Therefore, you may find information about features or equipment that are not included or
installed on your vehicle.
All information, specifications and illustrations in this Quick Reference Guide are those in effect at the time
of printing. INFINITI reserves the right to change specifications, performance, design or component suppliers
without notice and without obligation. From time to time, INFINITI may update or revise this Quick Reference
Guide to provide owners with the most accurate information currently available. Please carefully read and retain,
with this Quick Reference Guide, all revision updates sent to you by INFINITI to ensure you have access to
accurate and up-to-date information regarding your vehicle. Current versions of vehicle Quick Reference
Guides, Owner’s Manuals and any updates can also be found in the Owner section of the INFINITI website at
https://owners.infinitiusa.com/iowners/navigation/manualsAndGuides. If you have questions concerning any
information in your Owner’s Manual, contact INFINITI Client Support (see contact information listed above).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement