Badger Basket 340 BN Btu Series Specifications

Badger Basket 340 BN Btu Series Specifications
Data Industrial® 340 BN/MB BTU Energy Transmitter
Hydronic Energy Transmitter with RS-485 BACnet® and Modbus®
and Scaled Pulse Output
Output
Sensor Input
Power Out
Signal +
Signal Shield
Pulse Out +
Output LED
Data
Industrial
Btu ENERGY METER
Model: 340 BN/MB
S/N 340- 005100
Factory Port
AC C /DC -
Power In
AC L /DC +
Pulse Out -
D.I.C.
Comm
Port
Temp 2
1 2 3
NT PU PD
Input LED
+
REF
_
Temp 1
3 2 1
Comm LED
941700-0042-EN (July 2012) Rev. 2
Installation & Operation Manual
Data Industrial® 340 BN/MB BTU Energy Transmitter
Page ii
July 2012
Installation & Operation Manual
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surface Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
5
6
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DIN Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Temperature Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Direct Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thermowell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hot Tap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power Supply Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sensor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Series 200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SDI Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Other Flow Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature Element Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Thermistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Resistance Temperature Detectors (RTDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pulse Output Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting the RS-485 Buss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Communications Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting Via DIC COM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Flow Sensor Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Temperature Sensor Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Energy Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
RS-485 Network Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RS-485 Network Configuration – Pulse Out Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RS-485 Network Configuration – Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RS-485 Network Configuration – BACnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
RS-485 Network Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
July 2012
Page iii
Data Industrial® 340 BN/MB BTU Energy Transmitter
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
FLOW SENSOR INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pulse type sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sine wave sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TEMPERATURE SENSOR INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PULSE OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
OPERATING TEMPERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
WEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SENSOR CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
UNITS OF MEASURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Flow measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Energy measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Page iv
July 2012
Installation & Operation Manual
INTRODUCTION
The Data Industrial 340 BN/MB Btu Energy Transmitter from Badger Meter is an economical, compact device for hydronic
sub-metering applications. It uses an RS-485 connection for Modbus® and BACnet communication protocols and a solid state
switch for pulse output representing either flow or energy.
The 340 BN/MB Btu Energy Transmitter calculates thermal energy by integrating the liquid flow in a closed pipe system and
the differential temperature between the supply and return. The 340 BN/MB Btu Energy Transmitter requires one flow sensor
and two temperature sensors.
The temperature sensors can be two-wire 10k Ω Type II Thermistors or 100 or 1000 Ω RTDs that follow the IEC 751 curve.
The flow input may be provided by many of the Data Industrial line of flow sensors and other manufacturers' devices that
generate pulse or sine waves.
The onboard microprocessor and digital circuitry make precise measurements and produce accurate drift-free output. The
340 BN/MB Btu Energy Transmitter is programmed using the Badger Meter Windows® software and a Data Industrial Series
A301 programming cable. Calibration information for the flow sensor, units of measurement, communication protocol
settings and output scaling may be downloaded prior to installation or in the field.
The RS-485 Modbus settings include Baud Rate, Address and RTU/ASCII.
The RS-485 BACnet is an MS/TP slave device and includes Address, Baud Rate, Device Name, Device Instance Number and Max
Master Valve.
While the unit is connected to a PC or laptop computer, real-time flow rate, flow total, both temperature readings, energy rate
and energy total are available.
The 340 BN/MB Btu Energy Transmitter features three LEDs to indicate flow sensor activity, RS-485 activity and pulse output.
The 340 BN/MB Btu Energy Transmitter has an isolated solid state switch closure that is user programmed for units of energy
or flow. The output pulse width is adjustable from 10 ms to 5 sec.
The 340 BN/MB Btu Energy Transmitter operates on AC or DC power supplies ranging from 12 to 24 volts.
The compact cast epoxy body measures 3.65 x 2.95 inches (93 x 75 mm) and can be easily mounted on panels, DIN rails or
enclosures.
INSTALLATION
Mechanical Installation
The 340 BN/MB Btu Energy Transmitter may be surface mounted onto a panel, attached to DIN rails using adapter clips or wall
mounted using two optional enclosures.
Location
Although the 340 BN/MB Btu Energy Transmitter is encapsulated, all wiring connections are made to exposed terminals. The
unit should be protected from weather and moisture in accordance with electrical codes and standard trade practices.
In any mounting arrangement, the primary concerns are ease of wiring and attachment of the programming cable.
The unit generates very little heat so no consideration needs to be given to cooling or ventilation.
July 2012
Page 5
Data Industrial® 340 BN/MB BTU Energy Transmitter
Surface Mount Installation
The 340 BN/MB Btu Energy Transmitter may be mounted to the surface of any panel using double-sided adhesive tape or by
attaching fasteners through the holes in the mounting flanges of the unit.
1.60”
(40.6mm)
3.65”
(92.7mm)
Output
Sensor Input
Output LED
Data
Industrial
Btu ENERGY METER
Model: 340 BN/MB
S/N 340- 005100
D.I.C.
Comm
Port
Input LED
.60”
(15mm)
Temp 2
1 2 3
NT PU PD
2.95”
(74.9mm)
Power Out
Signal +
Signal Shield
.88”
(22mm)
Pulse Out +
Factory Port
AC C /DC -
Power In
AC L /DC +
Pulse Out -
+
REF
_
Temp 1
3 2 1
Comm LED
.20”
(5mm)
Figure 1: 340 BN/MB Dimensions
Wall Mounting
Optional metal and plastic enclosures are available to mount the 340 BN/MB Btu Energy Transmitter to a wall when no other
enclosure is used. The enclosure is first attached to the wall using fasteners through its mounting holes.
After wiring, the transmitter may be attached to the enclosure with the terminal headers facing in using the slots in the
mounting flanges. As an alternate mounting arrangement, the 340 BN/MB Btu Energy Transmitter may be fastened to the box
cover using double-sided adhesive tape.
5.125"
Top
4.50"
Top
3.25"
4.60"
4.50"
4.60"
Side
Side
2.00"
Bottom
2.25"
Figure 2: 340 BN/MB Metal (left) and Plastic (right) Box Dimensions
Page 6
July 2012
Installation & Operation Manual
DIN Rail Mounting
Optional clips snap onto the mounting flanges allowing the 340 BN/MB Btu Energy Transmitter to be attached to DIN 15, 32,
35 mm DIN rail systems.
Figure 3: DIN Rail Mounting
Temperature Sensor Installation
Badger Meter offers several styles of 10k Ω Thermistors and 100 Ω Platinum RTDs in both direct immersion and Thermowells.
The style selected depends on system requirements and pipe size.
Direct Insert
Generally, direct insert sensors are used for smaller pipe sizes.
Figure 4: Direct Insert
Thermowell
Thermowells are recommended for larger pipes that are more difficult to drain for service.
Figure 5: Thermowell
July 2012
Page 7
Data Industrial® 340 BN/MB BTU Energy Transmitter
Hot Tap
For pipes that cannot be drained even for initial installation, we offer a Hot Tap version.
Model THT – available in the 10k Ω Thermistor version only.
Figure 6: Hot Tap
Electrical Installation
All connections to the 340 BN/MB Btu Energy Transmitter are made to screw terminals on removable headers.
Wire
3/32" Flathead
Screwdriver
Series 300
Connector
Figure 7: Side View - Typical Series 300 Removable Connector Wiring
Page 8
July 2012
Installation & Operation Manual
Power Supply Wiring
The 340 BN/MB Btu Energy Transmitter requires 12-24 Volts AC or DC to operate. The power connections are made to the
ORANGE header. The connections are labeled beside the header. Observe the polarity shown on the label.
If a Badger Meter plug-in type power supply (Series A-1026 or A-503) is used, connect the black/white striped wire to the
terminal marked positive (+) and the black wire to the terminal marked negative (–).
AC or DC
Power Supply
DC or
AC Common
Earth
Ground
DC +
or
AC Load
Output
AC C /DC -
Power In
AC L /DC +
Pulse Out Pulse Out +
Output LED
Input LED
Model: 340
S/N 340- XXXXXX
Temp 2
1 2 3
Data
Industrial
REF
_
Temp 1
3 2 1
+
D.I.C.
Comm
Port
Sensor Input
Power Out
Signal +
Signal Shield
Comm LED
Figure 8: Sample Power Supply Wiring
NNOTE: Included with every 340 BN/MB Btu Energy Transmitter is a 340IK kit containing a screw, lock washer and nut to
connect the transmitter to earth ground. Connect the earth ground lug of the 340 BN/MB Btu Energy Transmitter to
a solid earth ground with as short a wire as possible. This will help prevent electrical interference from affecting the
transmitter’s normal operation.
July 2012
Page 9
Data Industrial® 340 BN/MB BTU Energy Transmitter
Output
Sensor Wiring
AC C /DC
D.I.C.
Comm
Port
Temp 2
1 2 3
NT PU PD
Input LED
Red
or Signal +
+
REF
_
Shield
(if applicable)
Temp 1
3 2 1
Series 200
or SDI Sensor
Model: 340
S/N 340- XXXXXX
Sensor Input
Power Out
Signal +
Signal Shield
Black
or Signal -
Factory Port
All flow sensor types connect to the four terminal headers labeled “Sensor Input.- ”
Pulse Out +
Power In
AC L /DC +
Pulse Out -
Comm LED
Figure 9: Sample Sensor Wiring Diagram
Series 200
Connect the red wire to sensor signal (+), black wire to sensor signal (–) and the bare wire to shield.
SDI Series
Connect the plus (+) terminal of the sensor to sensor signal (+) on the transmitter and the minus (–) terminal of the sensor to
sensor signal (–) on the transmitter. Connect the shield terminal of the sensor to the shield terminal of the transmitter.
Other Flow Sensors
The sensor input power out terminal supplies nominal 12V DC excitation voltage for three-wire sensors. Connect sensor signal
(+) and sensor signal (–) wires to transmitter terminals.
The 340 BN/MB Btu Energy Transmitter is very versatile and can accept both pulse and zero crossing sine wave flow sensors.
Excitation voltage is also provided for three-wire powered sensors (Example: hall effect, of Badger Meter Series 4000).
See the Programming section page 14 for configuration instructions.
Page 10
July 2012
Installation & Operation Manual
Temperature Element Wiring
Appropriate wire types and proper shielding is required for accurate temperature readings.
Since Btu calculations are based on Delta T cable, in order to maintain a balanced system, T1 and T2 wire runs should be kept
to approximately the same length, not to exceed 500 feet.
Thermistors
Badger Meter thermistors are not polarity-sensitive, therefore, wire color is unimportant. The thermistor located in the same
pipe as the flow sensor, termed temperature sensor T1, should be connected to terminals 2 and 3 on terminal block
Temp 1. The thermistor located in the other pipe, termed temperature sensor T2, should be connected to terminals 2 and 3 on
terminal block Temp 2. As shown in the thermistor wiring diagram (Figure 10), a jumper must be installed between terminals
1 and 3 for both the T1 and T2 input terminals. These terminals 1 and 3 are used for lead resistance compensation when 100
three-wire RTDs are used and must be jumpered when not used.
Supply
Temp 1
3 2 1
Return
Temp 2
1 2 3
Jumpers
T1
T2
10KΩ Thermistors
Figure 10: Thermistor Wiring Diagram
Resistance Temperature Detectors (RTDs)
Badger Meter RTDs are three-wire devices. Two of the wires are the same color and interchangeable. One wire is
current-carrying and connects to terminal #3, and the other is used for lead compensation and is connected to terminal #1.
The single color lead is attached to terminal 2. The RTD located in the same pipe as the flow sensor, temperature sensor T1,
should be connected to terminal block Temp 1. The RTD located in the other pipe line, temperature sensor T2, should be
connected to terminal block Temp 2.
Temp 2
1 2 3
Supply
Return
Temp 1
3 2 1
T2
T1
100Ω RTDs or 1000Ω RTDs
Figure 11: RTD Wiring Diagram
Pulse Output Wiring
The 340 BN/MB Btu Energy Transmitter has solid-state switch output rated for a maximum sinking current of 100 mA at 36V
DC. In most cases the pulse out (+) terminal of the 340 BN/MB Btu Energy Transmitter will connect to the input pulse (+) and
the pulse out (–) terminal to the input pulse (–) of the receiving device. Although labeled +/–, the pulse output is not actually
polarity sensitive and can switch low level AC loads if required.
These terminals are located on a separate two-terminal removable header on the 340 BN/MB Btu Energy Transmitter, labeled
“Output.”
July 2012
Page 11
Data Industrial® 340 BN/MB BTU Energy Transmitter
NOTE:
maximum sinking current
is 100 mA @ 36 VDC
Output
AC C /DC -
Power In
AC L /DC +
Pulse Input
Device
(-) (+)
Pulse Out Pulse Out +
Output LED
Figure 12: Sample Pulse Output Wiring Diagram
Connecting the RS-485 Buss
As shown in the Sample Pulse Output Wiring Diagram, the position of jumpers on each 340 BN/MB Btu Energy Transmitter
and wiring between each transmitter and the RS-485 network are different depending on where the transmitter is installed,
that is, its nodal position. For all but the final transmitter in a string, the three jumpers NT, PU and PD should be in the open
position, and only the (+) and (–) network terminals should be connected to the RS-485 buss. For the final 340 BN/MB Btu
Energy Transmitter in a Modbus network, the three jumpers NT, PU and PD should be in the closed position, and all three
network terminals, (+), (–) and REF, should be connected to the Modbus buss.
NNOTE: The 340 BN/MB Btu Energy Transmitter default Modbus or BACnet polling address must be changed before it is
introduced into an existing network to avoid possible address conflicts. Please refer to programming instructions in
the previous section.
Figure 13: Sample Wiring Diagram to Modbus Network
NOTE 1: Biasing, circuitry and resistors for PU, PD and NT terminals are integral parts of the 340 BN/MB Btu Energy
Transmitter.
NOTE 2: For the final 340 BN/MB Btu Energy Transmitter in a given RS-485 network string, NT, PU and PD jumpers should be
in the closed position. Otherwise, NT, PU and PD should be in the open position.
NOTE 3: For the final 340 BN/MB Btu Energy Transmitter in an RS-485 string, all three network terminals, (+), (-) and REF,
should be connected to the buss. Otherwise, connect only terminals (+) and (-) to the buss.
Page 12
July 2012
Installation & Operation Manual
Connection to the RS-485 network should not be made until the 340 BN/MB Btu Energy Transmitter has been configured per
the instructions in "Programming" on page 14.
See RS-485 Network Configuration on page 19.
Communications Cable Wiring
Field configuration requires a Data Industrial programming kit (consisting of a custom cable and software) and a PC running
Windows 9x, ME, NT, 2000 or Windows 7. In order to connect, the 340 BN/MB Btu Energy Transmitter must be powered, and
the Data Industrial Series A301 cable must be connected to the 340 BN/MB Btu Energy Transmitter COM port connector and
an available 9-pin COM port on a computer. USB to COM Port adapters can be used if the DB9 COM port is not available.
NNOTE: The Data Industrial A301 Cable will work with all Series 300 products. However the older version of the cable (A300)
does not have sufficient bandwidth to work with the 340 BN/MB Btu Energy Transmitters.
Badger Meter provides free programming software updates via the Internet for all Series 300 products. Go to
www.badgermeter.com. Software updates can be found in the Industrial/Impeller/Transmitter section.
Output
Sensor Input
Power Out
Signal +
Signal Shield
Pulse Out +
Output LED
Data
Industrial
Btu ENERGY METER
Model: 340 BN/MB
S/N 340- 005100
Factory Port
AC C /DC -
Power In
AC L /DC +
Pulse Out -
D.I.C.
Comm
Port
DIC COM
PortPort
D.I.C.
Comm
Temp 2
1 2 3
NT PU PD
Input LED
+
REF
_
Temp 1
3 2 1
Comm LED
Figure 14: Location of the DIC COM Port
July 2012
Page 13
Data Industrial® 340 BN/MB BTU Energy Transmitter
PROGRAMMING
Connecting Via DIC COM Port
Programming the 340 BN/MB Btu Energy Transmitter is accomplished by installing Badger Meter programming software on a
computer and entering data on templates of the Windows based program.
1. Load the interface software into the computer.
2. Power the 340 BN/MB Btu Energy Transmitter with 12-24V AC/DC.
3. Connect the computer to the transmitter with the Data Industrial Series A-301 communications cable to the socket
labeled “D.I.C. COM port”, taking care to properly align the tab on the plug and socket to maintain polarity. Connect
the DB9 connector of the Data Industrial Series A301 communications cable to a PC COM port that has the 340
software installed. If a DB9 COM port is not available, a USB to COM Port Adapter may be purchased locally.
4. Open the program and from the Device tab and select 340 as shown in the dialog box below.
Figure 15: Select 340
5. After the 340 device has been selected, select the Type, 340BN/MB.
Figure 16: Device Type
Page 14
July 2012
Installation & Operation Manual
6. Once 340BN/MB has been selected, the appropriate COM port can be selected from the Configuration tab.
Figure 17: Select Set COM Port
Figure 18: Select the COM Port
7. If the COM and Device type have been properly selected, the “---” will be replaced with values.
NNOTE: If this does not occur, communication has not been established and you cannot continue to the next step. If it does
not connect automatically try clicking on Poll Now.
July 2012
Page 15
Data Industrial® 340 BN/MB BTU Energy Transmitter
NNOTE: If communication still does not occur and you are using a DB9 to COM 1 or COM2, try using a USB to COM adapter.
This will usually create a new COM port that was not previously listed. Windows Device Manager can be helpful in
determining the actual COM ports that are available.
Figure 19: Device Manager
Select this new port created by the adapter and the screen should change as shown (Figure 20). Notice that the “---“
are replaced with values. This confirms normal communications.
Figure 20: Screen Change
Page 16
July 2012
Installation & Operation Manual
8. When communication has been confirmed, click on the Parameters button. The Parameters screen is displayed.
Figure 21: Parameters Screen
9. From this screen set up the following:
1. Flow Sensor Type, Scaling and Units
2. Temperature Sensor Type, Units, Mode and Zeroing
3. Energy Calculation Units of Measure
4. Filter Coefficients (Flow and Energy averaging for reading stability)
5. Scaled Pulse Output Resolution and Pulse Width
6. RS-485 Network Configuration (BACnet or Modbus)
10. Be sure to press Send before leaving this page to save any wanted changes.
Refresh rereads the unit and refreshes the screen. Defaults will restore all factory settings. Exit returns to the Main
Screen.
Figure 22: Parameter Screen Buttons
July 2012
Page 17
Data Industrial® 340 BN/MB BTU Energy Transmitter
Flow Sensor Section
Figure 23: Pulse or Sine
For most Data Industrial sensors, the sensor type is “Pulse”, and the “K” and “Offset” values can be found in the respective Flow
Sensor Manual.
“Sine” is used for zero-crossing flow sensors (some turbine meters, etc.)
Several flow rate and flow total units of measure can be selected from the pull-down menu.
Temperature Sensor Section
Figure 24: Sensor Attributes
First choose the Sensor Type (10K Ω Thermistor, 100 Ω RTD, or 1K RTD).
The Calc(ulation) Mode has three selections. Initially, it is best to choose “Absolute.” In this mode the Energy Rate and Total will
be calculated as a positive value regardless of the direction of energy flow.
In the T1>T2 Mode, energy will only be calculated if the T1 sensor is warmer than the T2 sensor. If T1 is cooler than T2, the
energy rate will remain at 0.0 and the energy total will not increase.
In the T1<T2 Mode, energy will only be calculated if the T1 sensor is cooler than the T2 sensor.
The T1= and T2= are simply for reference to indicate the current temperature readings.
This is useful in using the zeroing feature explained on page 19.
Page 18
July 2012
Installation & Operation Manual
The Zero Temp Diff is a very powerful feature in this product which allows any inaccuracies of drift in the temperature
sensors, or the 340 BN/MB Btu Energy Transmitter temperature measurements, to be cancelled out.
This correction can be either manually typed in or if the temperature sensors are known to be at exactly the same
temperature, the Zero Temp Diff button can be used to automatically zero the difference between the two readings. To
correct for any erroneous entries, simply manually type 0.0 in both fields.
This feature must be used with caution. If used incorrectly, the temperature readings will be incorrect and the energy rates
and totals will also be in error.
Energy Calculation
Figure 25: Rate and Total Units
Select the units of measure for energy rate and total from the pull-down menus.
Filter Coefficients
Figure 26: Filter Coefficients
For most applications leave the default setting of 5. If the flow rate or energy rates are unstable for some reason (from a
disturbed flow profile, for example) this value can be increased as needed.
Pulse Output
Figure 27: Flow or Energy
The pulse output can represent either flow or energy. Units will be the same as selected in the previous sections.
Pulse width and pulse resolution will be selected based on the requirements of the receiving device and system requirements.
July 2012
Page 19
Data Industrial® 340 BN/MB BTU Energy Transmitter
RS-485 Network Configurations
The RS-485 Section can be configured in three ways:
•
Pulse Out Only – RS-485-OFF
•
Modbus
•
BACnet
The following sections explain each in detail.
RS-485 Network Configuration – Pulse Out Only
Figure 28: Pulse Out Only Option
If the Modbus or BACnet communications are not going to be used, the Pulse Out Only setting can be selected. This will
disable the RS-485 Network.
RS-485 Network Configuration – Modbus
Figure 29: Modbus Option
Select Modbus, to access the Modbus pull down menus.
Select the Address, Bit Rate (Baud Rate) and Mode (RTU or ASCII).
The 340 BN/MB Btu Energy Transmitter uses IEEE 754 Float - Data Located in “Holding Registers.”
The 340BN/MB Data Format is “Float 32” where the Data is stored across two “Holding Registers”.
In the case of Temperature 1, the Upper Byte is stored in Register 40002, and the Lower Byte is stored in Register 40001,
sometimes referred to as an ABCD to CDAB format. This is done to permit backwards compatibility with older 16-bit systems.
For example, a temperature of 53.36° F when converted to IEEE 754 is “425570A4.” So in the case of the 340BN/MB,
Register # 40001 = 70A4 Hex and Register # 40002 = 4255 Hex. See the table on the next page for additional information.
Page 20
July 2012
Installation & Operation Manual
Modbus Register Map
Model 340BN/MB Register Map
July 2012
Register Name
Address
Data Type
Read/Write
Temperature 1
40001 + 40002
IEEE 754 Float
Read Only
Temperature 2
40003 + 40004
IEEE 754 Float
Read Only
Flow Input (Hz)
40005 + 40006
IEEE 754 Float
Read Only
Total Flow
40007 + 40008
IEEE 754 Float
Read Only
Total Energy
40009 + 40010
IEEE 754 Float
Read Only
Flow Rate
40011 + 40012
IEEE 754 Float
Read Only
Energy Rate
40013 + 40014
IEEE 754 Float
Read Only
K Factor
40015 + 40016
IEEE 754 Float
Read Only
Offset
40017 + 40018
IEEE 754 Float
Read Only
Temp Calc Mode
40019 + 40020
IEEE 754 Float
Read Only
Flow Filter Coef
40021 + 40022
IEEE 754 Float
Read Only
Temp Filter Coef
40023 + 40024
IEEE 754 Float
Read Only
Specific Heat
40025 + 40026
IEEE 754 Float
Read Only
Fluid Density
40027 + 40028
IEEE 754 Float
Read Only
T1 A Coefficient
40029 + 40030
IEEE 754 Float
Read Only
T1 B Coefficient
40031 + 40032
IEEE 754 Float
Read Only
T1 C Coefficient
40033 + 40034
IEEE 754 Float
Read Only
Temp 1 Offset
40035 + 40036
IEEE 754 Float
Read Only
T1 A Coefficient
40037 + 40038
IEEE 754 Float
Read Only
T1 B Coefficient
40039+ 40040
IEEE 754 Float
Read Only
T1 C Coefficient
40041 + 40042
IEEE 754 Float
Read Only
Temp 1 Offset
40043 + 40044
IEEE 754 Float
Read Only
Page 21
Data Industrial® 340 BN/MB BTU Energy Transmitter
RS-485 Network Configuration – BACnet
Figure 30: BACnet Option
Select BACnet to access the BACnet pull down menus.
Select the Bit Rate (BAUD rate) to match other devices on the network.
BACnet Device Name can be set to help identify this device and location.
BACnet Device ID (Incidence #) is a unique number that identifies this device on the network. Typically, the first part of the
number is the same as the network #, and the last two characters are the same as the Address.
NNOTE: This is not a requirement, but can help in system planning.
BACnet Object Map
Page 22
Description
ID
Name
Out of
Service
Units
Analog Input
AN1
TempIn
FALSE
º C, º F
Analog Input
AN2
TempOut
FALSE
º C, º F
Analog Input
AN3
FreqIn
FALSE
Hz
Analog Input
AN4
VolFlow
FALSE
gpm, gph, lpm, lph,
ft3/s, ft3/m, ft3/h, m3/s,
m3/min, m3/h
Analog Input
AN5
EnrgyFlow
FALSE
kBtu/min, kBtu/h, kW,
MW, HP, Tons
Analog Value
AV1
TotalVol
FALSE
gallons, liters, ft3, m3
Analog Value
AV2
TotEnergy
FALSE
Btu, kBtu, MBtu, kWh,
MWh, kJ, MJ
Analog Value
AV3
Kfactor
FALSE
dimensionless
Analog Value
AV4
Offset
FALSE
dimensionless
Analog Value
AV5
TempMode
FALSE
dimensionless
Analog Value
AV6
FFilterCoef
FALSE
dimensionless
Analog Value
AV7
TFiltCoef
FALSE
dimensionless
Analog Value
AV8
SpHtCapac
FALSE
Btu/lb-F
Analog Value
AV9
Density
FALSE
lb/gallon
Analog Value
AV10
InTACoef
FALSE
dimensionless
Analog Value
AV11
InTBCoef
FALSE
dimensionless
Analog Value
AV12
InTCCoef
FALSE
dimensionless
Analog Value
AV13
InTOffset
FALSE
º C, º F
Analog Value
AV14
OutTACoef
FALSE
dimensionless
Analog Value
AV15
OuTBCoef
FALSE
dimensionless
Analog Value
AV16
OutTCCoef
FALSE
dimensionless
Analog Value
AV17
OutTOffset
FALSE
º C, º F
July 2012
Installation & Operation Manual
BACnet Protocol Implementation Conformance Statement
Products
Product
Model Number
Protocol Revision
340 BN/MB
B340BN
135-2001
Software Version
Firmware Version
Rev 1.00
Vendor Information
Badger Meter, Inc
6116 E 15th Street
Tulsa, OK 74112
www.badgermeter.com
Product Description
The 340 BN/MB Btu Energy Transmitter is a low cost, flow and temperature sensor interface used in submetering applications. An
additional communication design feature provides connectivity for BACnet® MS/TP.
BACnet Standardized Device Profile
Product
340 BN/MB
Device Profile
Tested
BACnet Smart Sensor (B-SS)
Supported BIBBs
Product
340 BN/MB
Supported BIBBs
BIBB Name
DS-RP-B
ReadProperty-B
DS-WP-B
WriteProperty-B
Tested
Standard Object Types Supported
Object Type
Creatable
Deletable
340 BN/MB
Product
Analog Input
No
No
340 BN/MB
Analog Value
No
No
340 BN/MB
Device
No
No
Tested
Data Link Layer Options
Product
340 BN/MB
Data Link
Options
MS/TP Slave
Tested
Baud rates 9600, 19200, 38400,
75800
Segmentation Capability
Product
Segmentation Type
Supported
Window Size
Tested
(M8/TP product limited to1)
340 BN/MB
Able to fragment segmented messages
No
N/A
Device Address Binding
Product
340 BN/MB
Static Binding Supported
Tested
No
N/A
Character Sets Suported
Tested
Character Sets
Product
340 BN/MB
July 2012
ANSI X3.4
Page 23
Data Industrial® 340 BN/MB BTU Energy Transmitter
RS-485 Network Test
Figure 31: RS-485 Test
The Configuration Software has an RS-485 test program.
Although it uses Modbus settings, it is testing RS-485 communication.
The test requires connection to a COM port using the Data Industrial A302-20 RS 485 to RS-232 convertor cable. This cable can
also be helpful with other diagnostics programs and devices that use an RS-232 port to communicate.
When testing the RS-485 network, it is sometimes helpful to connect to some other location instead of directly to the 340
BN/MB Btu Energy Transmitter. When testing in this way the RS-485 end connector can be removed, and the wires can be
connected directly to the RS-485 pairs.
The following table may be helpful to make connections.
302 Cable w/RS-485 End
340 BN/MB
340 N2
Series 3000
Red
RS-485 +
N2 +
RS-485B
White
RS-485 –
N2 –
RS-485A
Black
REF
REF
RS-485 Gnd
When the RS-485 Test button is selected the following screens appear:
Figure 32: Test Screens
Page 24
July 2012
Installation & Operation Manual
Factory Default Settings
The table below is a list of factory default setting for all 340BN/MB variables. These settings can be changed by accessing the
parameters to best fit your application, and if desired, recorded in the table for future reference.
July 2012
Description
Default Value
Flow Sensor Type
Pulse
"K" Offset
1
"Offset" Value
0
Flow Rate
gpm
Flow Total
gallons
Temperature
ºF
Energy Calculation
absolute
Temperature Sensor Type
thermistor
Energy Rate
kBtu/hr
Energy Total
Btu
Flow Filter Coefficient
5
Energy Filter Coefficient
1
Energy Filter Coefficient
1
MS/TP Address
1
MS/TP Baud Rate
9600
BACnet Device #
—
BACnet Max Master
127
Customer Value
Page 25
Data Industrial® 340 BN/MB BTU Energy Transmitter
SPECIFICATIONS
POWER
Power supply options:
12…35V DC
12…24V AC
Current draw:
115 mA max. @ 12V DC
FLOW SENSOR INPUT
Pulse type sensors
Signal amplitude:
2.5V DC threshold
Signal limits:
Vin < 12V (DC or AC peak)
Frequency:
4…10000 Hz
Pull-up:
2k Ω to 15V DC
Sine wave sensors
Signal amplitude:
30 mV p-p threshold
Signal limits:
Vin < 12V (DC or AC peak)
Frequency:
4…10000 Hz
Excitation voltage 3-wire sensors
7.0V DC to 11.4 V DC 500 Ω source impedance
TEMPERATURE SENSOR INPUT
2 required:
10k Ω thermistor, 2 wire, type II,10k Ω, @ 25°C
100 Ω RTD, Platinum three wire,
1000 Ω RTD, Platinum, two or three wire
RTDs follow IEC 751 DIN Curve
PULSE OUTPUT
OPERATING TEMPERATURE
0…70° C
32…158° F
Storage Temperature
– 40…85° C
– 40…185° F
WEIGHT
4.8 oz with connector headers installed
SENSOR CALIBRATION
Badger Meter –
Use K and Offset provided in sensor owner’s manual
Other sensors –
Check with factory
UNITS OF MEASURE
Flow measurement
Rate:
gpm, gph, l/sec, l/min, l/hr, ft3/sec, ft3/min,
ft3/hr, m3/sec, m3/min, m3/hr
Total:
gallons, liters, cubic feet, cubic meters
Energy measurement
Rate:
kBtu/min, kBtu/hr, kW, MW, hp, tons
Total:
Btu, kBtu, MBtu, kWh, MWh, kJ, MJ
Temperature Units:
Fahrenheit, Centigrade
PROGRAMMING
Requires PC or laptop running Windows® XP, Vista or
Windows 7
Data Industrial 340 BN/MB Programming Kit A301-20
containing software and programming cable
Pulse width:
Programmable 10 ms to 5 sec. in 50 ms steps
Pulse frequency:
Max of 10 Hz at 50 ms pulse width programmable to scaling
requirements of connected device (Flow or Energy)
Opto-isolated solid state switch
Operating voltage range:
0 to ± 45V (DC or AC peak)
Closed (on) state:
Load Current - 700 mA max.
over operating temperature range
Open (off ) state - leakage @ 70ºC
<1µA @ 45V (DC or AC peak)
Page 26
July 2012
Installation & Operation Manual
INTENTIONAL BLANK PAGE
July 2012
Page 27
Data Industrial is a registered trademarks of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities.
Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding
contractual obligation exists. © 2012 Badger Meter, Inc. All rights reserved.
www.badgermeter.com
The Americas | Badger Meter | 4545 West Brown Deer Rd | PO Box 245036 | Milwaukee, WI 53224-9536 | 800-876-3837 | 414-355-0400
México | Badger Meter de las Americas, S.A. de C.V. | Pedro Luis Ogazón N°32 | Esq. Angelina N°24 | Colonia Guadalupe Inn | CP 01050 | México, DF | México | +52-55-5662-0882
Europe, Middle East and Africa | Badger Meter Europa GmbH | Nurtinger Str 76 | 72639 Neuffen | Germany | +49-7025-9208-0
Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | +420-5-41420411
Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01
Asia Pacific | Badger Meter | 80 Marine Parade Rd | 21-04 Parkway Parade | Singapore 449269 | +65-63464836
China | Badger Meter | Rm 501, N° 11 Longyue Apartment | N° 180 Longjin Rd, Jiuting Songjiang District | Shanghai, China | 201615 | +86-21-5763 5412
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement