Moxa Technologies | UC-7420/7410 | User`s manual | Moxa Technologies UC-7420/7410 User`s manual

Moxa Technologies UC-7420/7410 User`s manual
UC-7400 Hardware User’s Manual
Sixth Edition, April 2009
www.moxa.com/product
© 2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
UC-7400 Hardware User’s Manual
The hardware described in this manual is furnished under a license agreement and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright © 2009 Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of Moxa.
Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the
publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: +1-714-528-6777
Fax: +1-714-528-6778
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: +86-21-5258-9955
Fax: +86-10-6872-3958
Moxa Europe:
Tel: +49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Table of Contents
Chapter 1
Introduction ..................................................................................................1-1
Overview.................................................................................................................................. 1-2
Package Checklist .................................................................................................................... 1-2
Product Features ...................................................................................................................... 1-2
Product Hardware Specifications............................................................................................. 1-3
Chapter 2
Appearance and Dimensions......................................................................2-1
Appearance .............................................................................................................................. 2-2
Dimensions .............................................................................................................................. 2-6
Hardware Block Diagrams....................................................................................................... 2-9
LED Indicators........................................................................................................................2-11
Reset-type Buttons..................................................................................................................2-11
Reset Button ............................................................................................................... 2-11
Reset to Default Button .............................................................................................. 2-11
Real Time Clock .................................................................................................................... 2-12
Chapter 3
Mounting Options ........................................................................................3-1
Wall or Cabinet Mounting........................................................................................................ 3-2
DIN-Rail Mounting.................................................................................................................. 3-3
Chapter 4
Hardware Connection Description .............................................................4-1
Wiring Requirements ............................................................................................................... 4-2
Connecting the Power .............................................................................................................. 4-2
Grounding the UC-7400 .......................................................................................................... 4-2
Connecting to the Network ...................................................................................................... 4-3
Connecting to a Serial Device.................................................................................................. 4-3
Connecting to the Console Port ............................................................................................... 4-3
PCMCIA .................................................................................................................................. 4-4
CompactFlash .......................................................................................................................... 4-4
USB.......................................................................................................................................... 4-4
DI/DO ...................................................................................................................................... 4-4
1
Chapter 1
Introduction
Thank you for purchasing the Moxa UC-7400 RISC-based ready-to-run embedded computer.
The product features 8 RS-232/422/485 serial ports, dual 10/100 Mbps Ethernet ports, 8 digital
input and 8 digital output channels, a PCMCIA interface for wireless LAN communication, and
CompactFlash and USB ports for adding additional memory. All of these features make the
UC-7400 series ideal for your embedded applications.
This manual introduces the hardware of the UC-7400 series embedded computers. After a brief
introduction of the hardware features, we focus on installing and configuring the hardware.
The following topics are covered in this chapter:
‰
‰
‰
‰
Overview
Package Checklist
Product Features
Product Hardware Specifications
UC-7400 Hardware User’s Manual
Introduction
Overview
The Moxa UC-7400 Series of RISC-based ready-to-run embedded computers (referred to
collectively as the UC-7400) includes the UC-7402, UC-7408, UC-7410, and UC-7420. The
UC-7400 features 8 RS-232/422/485 serial ports, dual 10/100 Mbps Ethernet ports, 8 digital input
and 8 digital output channels, a PCMCIA interface for wireless LAN communication, a
CompactFlash slot for flash disk expansion, and USB ports for adding additional memory (such as
a USB Flash disk).
The UC-7400 uses an Intel XScale IXP422 266 MHz RISC CPU. Unlike the X86 CPU, which
uses a CISC design, the IXP-422’s RISC design architecture and modern semiconductor
technology provide the UC-7400 with a powerful computing engine and communication functions,
but without generating a lot of heat. The built-in 32 MB NOR Flash ROM and 128 MB SDRAM
give you enough memory to run your application software directly on the UC-7400. Since the dual
LAN ports are built into the IXP422 CPU, the UC-7400 makes an ideal communication platform
for network security applications. If your application requires placing the UC-7400 at a site that is
not located near an Ethernet LAN connection, you can connect to the network by attaching a
wireless LAN card to the UC-7400’s PCMCIA port.
Package Checklist
All models of the UC-7400 series are shipped with the following items:
y
y
y
y
y
y
y
y
y
y
1 UC-7400 series embedded computer
Wall-mounting kit
DIN-Rail mounting kit
Quick Installation Guide
Document & Software CD
Cross-over Ethernet cable
CBL-RJ45M9-150: 150 cm, 8-pin RJ45 to DB9 male serial port cable
(does not apply to the UC-7402)
CBL-RJ45F9-150: 150 cm, 8-pin RJ45 to DB9 female console port cable
Universal Power Adaptor
Product Warranty Statement
NOTE: Please notify your sales representative if any of the above items are missing or damaged.
Product Features
y
y
y
y
y
y
y
y
y
y
y
y
Intel XScale IXP-422 266 MHz processor
128 MB RAM, 32 MB Flash ROM onboard
8 RS-232/422/485 serial ports (UC-7408/7410/7420 only)
8 digital input and 8 digital output channels (UC-7408 only)
Dual 10/100 Mbps Ethernet ports
USB 2.0 host for mass storage devices (UC-7420 only)
PCMCIA, wireless LAN expansion (supports 802.11b/g)
CompactFlash for storage expansion (UC-7408/7410/7420 only)
LCM display and keypad for HMI (UC-7410/7412 only)
Ready-to-run Linux/WinCE 5.0.NET platform
DIN-Rail or wall mounting installation
Robust, fanless design
1-2
UC-7400 Hardware User’s Manual
Introduction
UC-7402
UC-7408
UC-7410/7420
Product Hardware Specifications
UC-7402
Serial Port
Serial Protection
Data Bits
Stop Bits
Parity
Flow Control
Speed
Serial Console
UC-7410
UC-7420
Intel XScale
IXP422 266 MHz
128 MB
32 MB
CPU
RAM
Flash
LAN
UC-7408
Auto-sensing 10/100 Mbps × 2 with built-in 1.5 KV magnetic isolation protection,
RJ45 connector
--RS-232/422/485 × 8, RJ45 connector
--15 KV ESD for all signals
--5, 6, 7, 8
--1, 1.5, 2
--none, even, odd, space, mark
--RTC/CTS, XON/XOFF, RS-485 ADDCTM
--50 bps to 921.6 Kbps
RS-232 × 1
RJ45 Connector
----1*
RS-232 × 1
RJ45 Connector
DI × 8, DO × 8
--1*
RS-232 × 1
RJ45 Connector
----1*
N/A
DI/DO
USB 2.0 Hosts
USB 1.1 Client
PCMCIA
Cardbus × 1 **
Cardbus × 1 **
Storage
N/A
CompactFlash × 1*** CompactFlash × 1***
Expansion
----LCM
128 × 64 dots
----5
Keypad
Yes
Real Time Clock
Yes
Buzzer
Reset Button
HW Reset × 1,
Reset to Default × 1
12 to 48 VDC
Power Input
Power
7W
8W
10W
Consumption
1-3
RS-232 × 1
RJ45 Connector
--2
1*
Cardbus × 1 **
CompactFlash × 1 ***
128 × 64 dots
5
12W
UC-7400 Hardware User’s Manual
Dimensions
(W × D × H)
Weight
Operating
Temperature
Storage
Temperature
Introduction
197 × 125 × 44 mm
830 g
Anti-Vibration
N/A
Anti-Shock
Regulatory
Approvals
Warranty
N/A
870 g
810 g
875 g
-10 to 60°C (14 to 140°F), 5 to 95% RH
-40 to 75°C (-40 to 167°F) for T models
-20 to 80°C (-4 to 176°F), 5 to 95% RH
-40 to 85°C (-40 to 185°F) for T models
1 g @ IEC-68-2-6,
sine wave (resonance 1 g @ IEC-68-2-6, sine wave (resonance
search), 5-500 Hz, 1 search), 5-500 Hz, 1 Oct/min, 1 cycle, 13
Oct/min, 1 cycle, 13 mins 17 sec axis
mins 17 sec axis
N/A
5 g @ IEC-68-2-27, half sine wave, 30 ms
EMC: CE Class A, FCC Class A
Safety: UL, cUL, TÜV
5 years
* USB Client function is reserved for future enhancement
** PCMCIA is designed for 802.11b/g wireless LAN card expansion
*** CompactFlash is designed for Flash memory card or Microdrive
1-4
2
Chapter 2
Appearance and Dimensions
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
Appearance
Dimensions
Hardware Block Diagrams
LED Indicators
Reset-type Buttons
¾ Reset Button
¾ Reset to Default Button
‰ Real Time Clock
UC-7400 Hardware User’s Manual
Appearance and Dimensions
Appearance
UC-7402 Rear View
12-48 VDC
Power Input
DC 12-48V
10/100 Mbps Ethernet x 2
PCMCIA
LAN1
LAN2 Console
CF
V+ V-
CF x 1
PCMCIA x 1
USB 1.1 Client x 1,
miniB Connector
RS-232
PPP/Console
UC-7402 Top View
UC-7402 Front View
Reset to
Default
Reset
2-2
Reset to Default
Hardware Reset
UC-7400 Hardware User’s Manual
Appearance and Dimensions
UC-7408 Rear View
12-48 VDC
Power Input
10/100 Mbps Ethernet x 2
DC 12-48V
PCMCIA
LAN1
LAN2 Console
CF
V+ V-
CF x 1
USB 1.1 Client x 1,
miniB Connector
RS-232
PPP/Console
PCMCIA x 1
UC-7408 Top View
UC-7408 Front View
8-ch Digital Output
8-ch Digital Input
D/O
D/I
1 2 3 4 5 6 7 8
Reset to
Default
1 2 3 4 5 6 7 8
Reset
RS-232/422/485 P1
P2
P3
P4
P5
P6
P7
P8
RJ45 RS-232/422/485
Connectors x 8
2-3
Reset to Default
Hardware Reset
UC-7400 Hardware User’s Manual
Appearance and Dimensions
UC-7410 Rear View
12-48 VDC
Power Input
10/100 Mbps Ethernet x 2
DC 12-48V
LAN1
LAN2 Console
V+ V-
USB 1.1 Client x 1,
miniB Connector
RS-232
PPP/Console
UC-7410 Top View
Graphics LCM
128 x 64 Dots
5 Buttons
UC-7410 Front View
RJ45 RS-232/422/485
Connectors x 8
RS-232/422/485
P1
P2
P3
P4
P5
P6
P7
P8
Reset to
default
Reset
Reset to
Default
Reset
2-4
Reset to Default
Hardware Reset
Reset to Default
Hardware Reset
UC-7400 Hardware User’s Manual
Appearance and Dimensions
UC-7420 Rear View
12-48 VDC
Power Input
10/100 Mbps Ethernet x 2
DC 12-48V
PCMCIA
LAN1
USB
LAN2 Console
USB 2.0 Host x 2,
A Type Connector
CF
V+ V-
CF x 1
RS-232
PPP/Console
PCMCIA x 1
USB 1.1 Client x 1,
miniB Connector
UC-7420 Top View
Graphics LCM
128 x 64 Dots
5 Buttons
UC-7420 Front View
RJ45 RS-232/422/485
Connectors x 8
RS-232/422/485
P1
P2
P3
P4
P5
P6
P7
P8
Reset to
default
Reset
2-5
Reset to Default
Hardware Reset
UC-7400 Hardware User’s Manual
Appearance and Dimensions
Dimensions
44 mm
[1.73"]
125 mm [4.92"]
UC-7402
197 mm [7.76"]
2-6
UC-7400 Hardware User’s Manual
Appearance and Dimensions
44 mm
[1.73"]
125 mm [4.92"]
UC-7408
197 mm [7.76"]
2-7
UC-7400 Hardware User’s Manual
Appearance and Dimensions
44 mm
[1.73"]
125 mm [4.92"]
UC-7410/7420
197 mm [7.76"]
2-8
UC-7400 Hardware User’s Manual
Appearance and Dimensions
Hardware Block Diagrams
The following block diagram shows the layout of UC-7402’s internal components.
Ethernet
USB
Client
Console LAN2 LAN1
RS-232
PCMCIA &
CompactFlash
PCI to cardbus
Bridge
PHY
PHY
XScale IXP422 266 MHz
32 MB Flash
128 MB SDRAM
PCI Bus
Power
Power
circuit
RTC
The following block diagram shows the layout of UC-7408’s internal components.
Ethernet
USB
Client
Console LAN2 LAN1
RS-232
PCMCIA &
CompactFlash
PCI to cardbus
Bridge
PHY
2
3
4
Power
circuit
RTC
Decoder
Moxa UART ASIC
1
PHY
XScale IXP422 266 MHz
32 MB Flash
128 MB SDRAM
PCI Bus
Power
5
6
7
RS-232/422/485
2-9
8
D/I x 8 D/O x 8
UC-7400 Hardware User’s Manual
Appearance and Dimensions
The following block diagram shows the layout of UC-7410’s internal components.
Ethernet
Console
RS-232
USB
Client
LAN2
LAN1
PHY
PHY
XScale IXP422 266 MHz
32 MB Flash
128 MB SDRAM
PCI Bus
Moxa UART ASIC
1
2
3
4
Power
Power
circuit
RTC
LCM Display
& Keypad
5
6
7
8
RS-232/422/485
The following block diagram shows the layout of UC-7420’s internal components.
S
2-10
UC-7400 Hardware User’s Manual
Appearance and Dimensions
LED Indicators
The UC-7408/7410/7420 have 12 LED indicators on the top panel. The UC-7402 has only 4 LED
indicators on the top panel (it does not have a serial port indicator). Refer to the following table for
information about each LED.
LED Name
Ready
LAN1, LAN2
Console
P1, P2, P3, P4,
P5, P6, P7, P8
Color
Green
Yellow
Green
Yellow
Green
Yellow
Green
Meaning
Power is ON, and system is ready (after booting up)
10 Mbps Ethernet connection
100 Mbps Ethernet connection
Console port is receiving RX data from the serial device.
Console port is transmitting TX data to the serial device.
Serial port is receiving RX data from the serial device.
Serial port is transmitting TX data to the serial device.
Reset-type Buttons
The UC-7400 computers have two reset-type buttons. The button labeled Reset has the same effect
as switching off the power and then switching the power back on. The button labeled Reset to
default returns the UC-7400 to its factory default configuration.
Reset Button
Pressing the Reset button initiates a hardware reboot. The button plays the same role as a desktop
PC’s reset button.
In normal use, you should NOT use the Reset Button. You should only use this function if the
software is not working properly. To reset an embedded Linux system, always use the software
reboot command />reboot to protect the integrity of the data being transmitted or processed.
Reset to Default Button
Press the Reset to default button continuously for at least 5 seconds to load the factory default
configuration. After the factory default configuration has been loaded, the system will reboot
automatically. The Ready LED will blink on and off for the first 5 seconds, and then maintain a
steady glow once the system has rebooted.
We recommend that you only use this function if the software is not working properly and you
want to load factory default settings. To reset an embedded Linux system, always use the software
reboot command />reboot to protect the integrity of data being transmitted or processed. The
Reset to default button is not designed to hard reboot the UC-7400.
2-11
UC-7400 Hardware User’s Manual
Appearance and Dimensions
ATTENTION
Reset to default preserves user’s data
The Reset to default button will NOT format the user directory and erase the user’s data.
Pressing the Reset to default button will only load the configuration file. All files in the /etc
directory will revert to their factory defaults, but other user data will still exist in the Flash ROM.
“Reset to Default” is not supported by UC-7410/7420 hardware versions V1.0
The Reset to default button is not supported by UC-7410/7420 hardware version V1.0. You can
identify the hardware version from the UC-7410/7420’s lower label. You need to contact Moxa
to determine the product’s hardware version. When contacting our customer support team, you
will need to provide the product’s Serial Number (S/N) that is found on UC-7420/7410’s lower
label.
Real Time Clock
The UC-7400’s real time clock is powered by a lithium battery. We strongly recommend that you
do not replace the lithium battery without help from a qualified Moxa support engineer. If you
need to change the battery, contact the Moxa RMA service team.
WARNING
There is a risk of explosion if the battery is replaced by an incorrect type.
2-12
3
Chapter 3
The following topics are covered in this chapter:
‰ Wall or Cabinet Mounting
‰ DIN-Rail Mounting
Mounting Options
UC-7400 Hardware User’s Manual
Mounting Options
Wall or Cabinet Mounting
The two metal brackets that come standard with the UC-7400 are used to attach the UC-7400 to a
wall or the inside of a cabinet. First, use two screws per bracket to attach the brackets to the
bottom of the UC-7400 (Fig. A). Next, use two screws per bracket to attach the UC-7400 to a wall
or cabinet (Fig. B).
Figure A: UC-7410/7420—Wall Mounting Brackets (bottom view)
Figure B: UC-74`0/7410—Wall Mounting Brackets (top view)
3-2
UC-7400 Hardware User’s Manual
Mounting Options
DIN-Rail Mounting
An aluminum DIN-Rail attachment plate is included with the product. If you need to reattach the
DIN-Rail attachment plate to the UC-7400, make sure the stiff metal spring is situated towards the
top, as shown in the following figures.
STEP1: Insert the top of the DIN-Rail
into the slot just below the stiff metal
spring.
STEP2: The DIN-Rail attachment unit
will snap into place as shown.
metal
spring
metal
spring
DIN-Rail
DIN-Rail
To remove the UC-7400 from the DIN-Rail, simply reverse Steps 1 and 2.
3-3
4
Chapter 4
Hardware Connection Description
This section describes how to connect the UC-7410/7420 to serial devices for first time testing
purposes.
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
Wiring Requirements
Connecting the Power
Grounding the UC-7400
Connecting to the Network
Connecting to a Serial Device
Connecting to the Console Port
PCMCIA
CompactFlash
USB
DI/DO
UC-7400 Hardware User’s Manual
Hardware Connection Description
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your UC-7400.
Wiring Caution!
Calculate the maximum possible current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
Temperature Caution!
Be careful when handling the UC-7400. When plugged in, the UC-7400’s internal components
generate heat, and the outer casing may feel hot to the touch.
You should also observe the following common wiring rules:
y
Use separate paths to route wiring for power and devices. If power wiring and device wiring
paths must cross, make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communication wiring and power wiring in the same wire
conduit. To avoid interference, wires with different signal characteristics should be routed
separately.
y
y
y
You can use the type of signal transmitted through a wire to determine which wires should be
kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can
be bundled together.
Keep input wiring and output wiring separate.
Where necessary, we strongly recommend that you label wiring to all devices in the system.
Connecting the Power
Connect the 12 to 48 VDC power line with the UC-7400’s terminal block. If the power is properly
supplied, the Ready LED will illuminate with a solid green color after 30 to 60 seconds have
passed.
Grounding the UC-7400
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screw to the grounding surface prior to
connecting devices.
SG
SG: The Shielded Ground (sometimes called Protected Ground)
contact is the left most contact of the 3-pin power terminal block
connector when viewed from the angle shown here. Connect the
SG wire to an appropriate grounded metal surface.
4-2
UC-7400 Hardware User’s Manual
Hardware Connection Description
ATTENTION
This product is intended to be mounted to a well-grounded mounting surface, such as a metal
panel.
Connecting to the Network
Connect one end of the Ethernet cable to one of the UC-7400’s 10/100M Ethernet ports (8-pin
RJ45) and the other end of the cable to the Ethernet network. If the cable is properly connected, the
UC-7410/7420 will indicate a valid connection to the Ethernet in the following ways:
1
8
1
8
The lower right corner LED indicator maintains a solid
green color when the cable is properly connected to a
100 Mbps Ethernet network. The LED will flash on and
off when Ethernet packets are being transmitted or
received.
The lower left corner LED indicator maintains a solid
orange color when the cable is properly connected to a
10 Mbps Ethernet network. The LED will flash on and
off when Ethernet packets are being transmitted or
received.
Pin
1
2
3
4
5
6
7
8
Signal
ETx+
ETxERx+
----ERx-----
Connecting to a Serial Device
Use properly wired serial cables to connect the UC-7408/7410/7420 to serial devices. The
UC-7408/7410/7420’s serial ports (P1 to P8) use 8-pin RJ45 connectors. The ports can be
configured by software for RS-232, RS-422, or 2-wire RS-485. The precise pin assignments are
shown in the following table:
1
8
Pin
1
2
3
4
5
6
7
8
RS-232
DSR
RTS
GND
TXD
RXD
DCD
CTS
DTR
RS-422
--TXD+
GND
TXDRXD+
RXD-----
RS-485-2w
----GND
--Data+
Data-----
Connecting to the Console Port
The UC-7400’s console port is an 8-pin RJ45 RS-232 port. The port can be used to connect to the
console utility from a remote console via a V90 or GPRS modem with PPP protocol. The pin
definition is the same as for the serial ports (P1 to P8). For normal data acquisition applications,
you should connect to the UC-7400’s serial ports (P1 to P8) via a V90 or GPRS modem. If you
would like to use the console port for normal data acquisition applications, you can set the Console
port to startup via PPP protocol.
4-3
UC-7400 Hardware User’s Manual
Hardware Connection Description
PCMCIA
The PCMCIA slot supports the CardBus (Card-32) card standard and 16-bit (PCMCIA 2.1/JEIDA
4.2) card standard. The slot supports +3.3 V, +5 V, and +12 V at a working voltage of 120
mA~1100 mA. Wireless LAN card expansion is optional. The wireless LAN card provided by
Moxa lets you connect the UC-7400 to a wireless LAN, with both 802.1b and 802.11g interfaces
supported. If you need device drivers for other kinds of PCMCIA cards, contact Moxa for
information on how to initiate a cooperative development project.
CompactFlash
The UC-7400 provides one CompactFlash slot that supports CompactFlash type I/II card
expansion. Currently, Moxa provides a CompactFlash disk for plug & play mass storage expansion.
You may also use flash disks available from most computer supply outlets. The CompactFlash card
is automatically mounted as a system partition on insertion.
If you need device drivers for other kinds of mass storage cards, contact Moxa for information on
how to initiate a cooperative development project.
USB
The UC-7420 provides two USB 2.0 Hosts and one USB 1.1 Client. The USB Host now supports
adding USB storage devices.
DI/DO
The UC-7408 support 8-ch digital input and 8-ch digital output. The 8 digital input channels and 8
digital output channels use separate terminal blocks.
1 2 3 4 5 6 7 8
4-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising