U-Line 2115R Installation guide

U-Line 2115R Installation guide
Installation Guide
2115R — Refrigerator
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
[email protected]
©2006 U-Line Corporation
2115R — Refrigerator
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Swing/Clearances Information . . . . . . . . . . . . . .
Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
Side-By-Side Installation Instructions . . . . . . . . . . . . . .
Custom 1/4'' Door Panel Insert . . . . . . . . . . . . . . . . . . .
Full Overlay Door Panel . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . .
Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . .
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of the 2115R . . . . . . . . . . . . . . . . . . . . . . . .
Relocating the Shelves . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . .
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Follow Safety Precautions
PLEASE READ all instructions completely before
attempting to install or operate the unit.
• This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician in accordance with applicable
electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
Danger means that failure to follow this safety
statement will result in severe personal injury or
Warning means that failure to follow this safety
statement could result in serious personal injury,
or death.
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
2115R — Refrigerator
General Precautions
2 Inspect and Plan
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
You have received a carton containing your 2115R
Refrigerator with a package inside containing a Use and
Care Guide and a Product Registration Card. Complete and
mail the Product Registration Card or register online at
www.U-LineService.com. Once your unit is installed, keep
the Use and Care Guide and this Installation Guide in a
safe place for future reference.
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
Your unit is Black, White or Stainless Steel. Black and
White units have a reversible door with a slightly
contoured handle across the top. They come with a flush
mounted door panel that, when removed, will accept a
custom 1/4-inch thick door panel or a 3/4-inch thick full
overlay door panel. Stainless Steel units are covered with
a protective coating and have been ordered left- or righthand hinged. The Stainless doors are not reversible and
do not accept custom panels. Please carefully follow the
directions that apply to your unit and your intended
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp edges.
Tools/Materials Required
• Do not lift the unit by the door or door handle.
• Screwdrivers — slotted and Phillips head
• Do not install the unit behind closed doors or in any
way that would obstruct airflow to the front grille,
which may cause the unit to malfunction.
• 1/4-inch thick door panel material and cutting tools
(Black or White units) (if installing a 1/4” Panel Insert)
• Full Overlay Door Panel Kit (part number U-OL2115B —
Black or part number U-OL2115W — White), 3/4-inch
door panel overlay, cutting tools, drill and bits (Black or
White units) (If installing a 3/4” Full Overlay)
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
Removing Protective Coating
(Stainless Steel Units Only)
When inspecting/installing a Stainless Steel unit, the
protective coating covering the unit must be removed
first. Start at a corner of the unit/door and pull back the
protective coating to remove it from the unit/door.
2115R — Refrigerator
After all the protective coating has been removed from
the unit/door, clean all Stainless Steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product
or a mild detergent and warm water solution and soft
cloth. Do NOT use abrasive cleaning agents.
3 Prepare Site
Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit
does not require additional air space for top, sides or rear.
However, the front grille must NOT be obstructed and
clearance is required for electrical connection in the rear.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable
product to prevent discoloration.
Note: Unit can NOT be installed behind a closed cabinet
Exterior Cleaning
Cut-Out Dimensions
(As Required)
Black and White Models:
• The door, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
Stainless Steel Models:
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation. (The part number
is 173348.) Comparable products are acceptable.
Frequent cleaning will remove surface contamination
that could lead to rust. Some installations may require
cleaning on a weekly basis.
Figure 1
Follow the cut-out drawing in Figure 1. The 15-3/16"
width allows 1/4" for ease in installation and removal of
the unit. 24" is the cabinet depth in most installations.
The unit is 23-1/4" deep including the handle on Black
and White models and 23-1/4" deep including the door
and not the handle on Stainless Steel models (see
Figure 2).
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel (this includes glass,
tile and counter cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
2115R — Refrigerator
Product Dimensions
Reversing the Door
(Black and White Units Only)
All U-Line units
(except Stainless
Steel models) may be
left- or right-hand
opening. The door
opening is easily
reversed by moving
the hinge hardware
to the opposite side.
The top hinge
hardware will be
used on the bottom
of the other side and
the bottom hinge
hardware will be
used on the top of
the other side (see
Figure 4).
Black and White
Stainless Steel
Figure 2
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 33 on Page 13).
To reverse the door:
1. Remove top
Figure 4
hinge screw pin
from door (Phillips screwdriver) (see Figure 5).
Remove door by tilting forward and lifting off bottom
hinge pin.
Door Swing/Clearances Information
Black and White units have a zero clearance for the door
to open 90° (see Figure 3). Stainless Steel models require
a minimum of 2-1/8" door clearance to accommodate the
handle if the unit is installed next to a wall or similar type
of structure.
2. Remove plastic screw plugs (3 each, top and bottom)
from new hinge location. Do not discard (see Figure 6).
1/4" Min.
2-1/8" Min.
Screw Plugs
Figure 6
Figure 5
Door Swing
Black and White
3. Remove top hinge (3 screws), reinstall hinge screw pin,
and remount on opposite side BOTTOM (see Figure 7).
Door Swing
Stainless Steel
Figure 3
2115R — Refrigerator
Other Site Requirements
4. Remove the two door closer inserts from the existing
bottom hinge and install as shown on the new bottom
hinge (see Figure 8).
Power Supply
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Electrical Specifications on Page 13.
Environmental Requirements
Many U-Line models are designed to operate in harsh
outdoor/marine environments. Special considerations
include the following:
• The units are designed to operate between 50°F (10°C)
and 110°F (40°C). High ambient temperatures (110°F
[40°C] or higher) may reduce the unit’s ability to reach
low temperatures and may also reduce the ice
production rate for those models with icemakers.
Figure 7
Figure 8
5. Remove existing bottom hinge (3 screws) and remount
on opposite side TOP. Remove hinge screw pin.
• If the ambient temperature is expected to drop below
45°F (7°C), drain all water from the unit to prevent
freezing damage not covered by the warranty.
6. Remove the plastic hole plug from the top of the door
to allow the pivot pin to be inserted in the new
location. Install the plug into the vacated hole on the
opposite side.
• For best performance, keep the unit out of direct
sunlight and away from heat generating equipment.
• For best performance and life outdoors, place under a
counter or provide shelter of some kind.
7. With bottom of door facing up, remove pivot plate
(2 screws), flip over, and remount on opposite side of
door (see Figure 9). Be sure notch in plate faces center.
• In climates where high humidity and dew points are
present, condensation may appear on outside surfaces.
This is considered normal. The condensation will
disappear when the humidity drops.
Figure 9
8. Holding door upright with top of door tilted forward,
place hole of door pivot plate on bottom hinge screw
pin (see Figure 10).
9. Tilt top of door into
position in top hinge and
install top hinge screw pin.
10. Install plastic screw plugs
removed in Step 2 in old
hinge holes (3 each, top
and bottom).
Figure 10
2115R — Refrigerator
Side-By-Side Installation
4 Prepare and Install Door Panel
(Black and White Units Only)
For a complete refreshment center, install your 2115R
Refrigerator beside a U-Line Ice Maker, Combo, or Wine
Captain Model (see Figure 11 for typical cut-out). Note
that each Side-By-Side Installation will be different.
Two types of custom door panels can be installed on your
Black or White unit to harmonize with or accent the
surrounding décor: a Custom 1/4" Insert or a Full Overlay.
If no custom door panel is used, go on to 5 Adjust Door.
• Cut-out width for a side-by-side installation is the total
of the widths listed under Cut-Out Dimensions in each
unit’s Installation Guide.
Custom 1/4'' Door Panel Insert
For example:
Door Panel Preparation
Placing a 2115R Refrigerator next to a 2115 series unit
would require a cut-out width of:
15-3/16" + 15-3/16" = 30-3/8"
A custom door panel can be inserted into the doorframe.
Custom door panels can be flat or raised, as long as the
maximum panel thickness where inserted into the door
reveal (channel) is 1/4"-thick. For raised panels, the depth
of the reveal is 1/4" on all four sides.
Placing a 2115R Refrigerator next to a 2175 series unit
would require a cut-out width of:
15-3/16" + 24-3/16" = 39-3/8"
• No trim kit is required. However, 1/4-inch space needs to
be maintained between the units to ensure
unobstructed door swing.
Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
type of structure.
• Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
Electrical Specifications.
For 2175 models cut the panel insert to the following
Custom 1/4" Dimensions:
Typical Side-By-Side Cut-Out
For 2115 & CLR2160 models cut the panel insert to the
following dimensions.
Custom 1/4" Dimensions:
1/4" Space
Between Appliances
The door panel must not weigh more than 20 lbs.
Door Panel Installation
Install the insert as follows:
Figure 11
Use care when handling the insert. Insert edges may be
1. Remove top hinge screw pin (using a Phillips
screwdriver, see Figure 12). Remove door by tilting
forward and lifting off bottom hinge pin.
2115R — Refrigerator
Full Overlay Door Panel
Door Panel Preparation
A full overlay door panel completely covers the
doorframe and handle to give a built-in appearance. See
your U-Line dealer for the optional Full Overlay Door
Panel Kit.
2175 Models:
P/N U-OL2175B -- Black
P/N U-OL2175W -- White
Figure 12
2115 & CLR2160 Models:
P/N U-OL2115B -- Black
P/N U-OL2115W --White
Figure 13
Appropriate hardware, Modified Handle, Replacement
Hinges and a copy of these instructions will be included in
the kit.
2. Pull door gasket out of groove (top edge of door only).
Start in the middle and pull outward, moving toward
the edge (see Figure 13). This may take some force.
1. Cut the overlay to the following dimensions (see
Figure 15).
3. Remove two outside screws holding door handle.
Slightly separate door handle from door (see
Figure 14).
Full Overlay Dimensions:
2175 Models:
Width: 23-3/4"
Height: 29-3/4"
4. Pull handle up and off.
5. Remove and discard
existing panel and
cardboard spacer.
2115 & CLR2160 Models:
Width: 14-3/4"
Height: 29-3/4"
The door panel must not weigh more than 20 lbs.
6. Slide custom door panel
insert into 1/4-inch
channel in door front.
7. Holding door gasket out
of the way, replace handle Figure 14
on door, making sure it is
seated properly on insert
and that screw holes line up.
Relief Notch
for Pivot Plate
8. Install two small screws removed in Step 3.
9. Starting at the corners and working inward, push door
gasket into place on door.
10. Place door on bottom hinge pin and install upper hinge
Rear View
Wood Panel
Figure 15
Rear View of wood panel for right-hand hinge shown. Use
mirror image for left-hand hinges.
2115R — Refrigerator
Installation Instructions
2. Create a relief (Figure 15) for pivot plate by cutting
notch in top corner of overlay panel. Refer to Figure
16 for exact specifications.
Removing Existing Door
1. Remove the door shelves by first pulling shelves up at
a 45° angle, then straight out.
2. Remove top hinge screw pin (Phillips screwdriver).
Remove the door by tilting forward and lifting off the
bottom hinge pin.
ø 0.177" (#16 Drill)
11/16" Deep
3. Pull door gasket out of the groove (top edge of door
only). Start in the middle and pull outward, moving
toward the edge (see Figure 17). This may take some
1/4" Ref
Old Handle
New Handle
3/4" Min Ref
Figure 16
ø 5/16" x 1/4" Deep
Chamfer 1/32" x 45°
Figure 17
Figure 18
4. Remove the two screws located on both sides of the
Route notch in top corner of overlay panel as shown
(see Top and Side Views). Top of notch is entire depth
of panel, front to back.
5. Remove the handle and discard. (This handle will be
replaced with the Overlay Handle included in the Full
Overlay Door Panel Kit.)
Width: 31/32"
Depth: 1/8"
6. Slide the existing door panel out of the doorframe.
Attaching the Full Overlay Panel
Be careful not to drill too deep! Drilling holes too deep
may destroy your door panel.
1. Place and tape the existing door panel on the back of
the overlay panel (see Figure 19) and drill holes
through both panels according to Figure 20. Remove
tape adjoining the panels and enlarge the six holes in
the steel (black/white vinyl color) panel using a 0.201"
(#7) drill.
3. Drill hole for upper door hinge (top of panel) (see
Figure 16, Top View).
0.177" diameter
(#16 drill) x 11/16" deep
2. If a user-supplied cabinet handle will be used, attach its
hardware to the overlay panel at this time.
4. Drill hole for lower door hinge (see Figure 16, Bottom
5/16" diameter x 1/4" deep
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood
when hardware is installed.
2115R — Refrigerator
Door Panel
Back of
Wood Panel
Door Panel
1-3/4" Top
Side of
Wood Panel
#10 x 5/8"
Round Head Screw
Seven Required
Top of
Wood Panel
Both Sides
Figure 19
Plastic Spacer
Seven Required
Figure 21
4. Remove the existing bottom pivot plate and replace
with the Full Overlay pivot plate (see Figure 22).
2-5/8" ± 1/4"
Drill ø 5/32" x 3/8" Deep
7 Places Model 2175
6 places Model 2115 and CLR2160
15-9/16" ± 1/4"
Wood Panel Bottom Pivot Plate
(5/8" Longer Than
Existing Bottom Pivot Plate,
Flush Side Facing Out)
Existing Bottom Pivot Plate
(Remove and Discard)
#8-32 x 3/8" SEMS Hex Screw
Two Places
For use with #10 x 5/8"
Wood Screw and Nylon Spacer
Figure 22
28-7/8" ± 1/4"
Door panel and overlay panel must be aligned properly or
the door will not operate correctly.
Assembling the Door
For use on
Model 2175 Only
1. Install the assembled panel by sliding the original door
panel back into the doorframe.
2. Replace the Overlay Handle and secure with the two
screws removed in Step 4 under Removing Existing
Figure 20
3. Attach Overlay cap to door, opposite side of where
hinges will be (see Figure 23).
3. Attach the door panel to the overlay panel using #10 x
5/8" wood screws and nylon spacers. The nylon spacers
fit between the overlay panel and the door panel as
shown in Figure 21. The spacers allow the original
door panel to slide back into the 1/4"-thick door
reveal (channel).
Overlay Cap
3/4" Wood Panel
Replacement Handle
Figure 23
2115R — Refrigerator
4. Attach Top Pivot Plate to door handle, on side where
hinges will be. Use the two #8-32 x 1/2" Flat Head
Phillips screws (Black) supplied with kit (see Figure 24).
#8-32 x 1/2" Flat Head Screws
Black, Two Places
3/4" Wood Overlay
Existing Door
Door Closure Top
Top Pivot Plate
Screw to attach Handle
Removed in step 4
Door Closure
Pivot Post
Figure 24
#8-32 x 1/2" Flat Head Screw
Three Places
Wood Panel Bottom Hinge Plate
(5/8" Longer than Existing Bottom Hinge Plate)
Figure 26
5. Starting at the corners and working toward the center,
push the door gasket back into place.
Installing the Door
Pivot posts must be cleaned. Closers must also be clean
and greased to ensure proper operation.
1. Remove the existing hinges from the unit, saving the
door closure assembly.
5. Place the modified door onto the pivot post.
2. Install the new Replacement Top Hinge onto the unit
(see Figure 25).
6. Position door and install the pivot post into the top
hinge (using the Phillips screwdriver).
7. Adjust door as needed for proper closure.
Wood Panel Top Hinge Plate
(5/8" Longer than Existing Top Hinge Plate)
8. Check to see that light goes off when the door closes.
Pivot Post
9. Reinstall the door shelves by lining up the bosses and
first pushing straight in, then down at a 45° angle.
#8-32 x 1/2"
Flat Head Screw
Three Places
Top Pivot Plate
Figure 25
Door Panel
3. Install the pivot post into the new Replacement Bottom
Hinge (using the Phillips screwdriver) and install the
hinge onto the unit.
4. Replace the door closure assembly onto the bottom
pivot post (see Figure 26). Be sure that bosses on
closers align with holes in hinge and hinge plate.
2115R — Refrigerator
5 Adjust Door
Checking Door Alignment
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
Properly aligned, the door should be 1/8" below the top of
the unit’s cabinet, NOT flush with the top (see Figure 27).
Door Edge
Door Edge
Figure 29
3. See Figure 29. If the top far edge of the door needs to
move UP, move the hinge plate toward the outside of
the door and retighten screws. If the top far edge of the
door needs to move DOWN, move the hinge plate
toward the inside of the door and retighten screws.
Figure 27
4. Mount the door to recheck alignment and repeat Steps
2 and 3 if further adjustment is necessary.
1. Compare the top edge of the door to the top edge of
the cabinet.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
2. If the door edge is 1/8" below and parallel to the top of
the cabinet, go on to 6 Prepare Power Supply. If it is
not, note whether the side opposite the hinge needs to
be moved UP or DOWN, and use the following
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
Note: If door is adjusted correctly, but panel is not square
with the adjacent cabinets, slight adjustments can be
made by drilling the holes in the vinyl coated steel panel
slightly oversized. See Figure 21 on Page 10.
7. Reinstall the closers, lining
up the bosses with holes in
hinge and hinge plate (see
Figure 30).
Adjusting Door Alignment
8. Mount the door, install top
hinge pivot pin and go on
to 6 Prepare Power
1. Remove top hinge screw
pin (7/64" Allen wrench or
Phillips screwdriver,
depending on your unit’s
construction, see
Figure 28). Remove door
by tilting forward and
lifting off bottom hinge
2. With door upside-down,
loosen but do not remove
the two screws on the
door’s bottom hinge plate.
Figure 30
Figure 28
2115R — Refrigerator
6 Prepare Power Supply
7 Level the Unit
Electrical Specifications
Leveling Information
Note: It is recommended that the unit is level.
1. Use a level to check
the levelness of the
refrigerator from
front to back and
from side to side.
Level should be
placed along top
edge and side edge
as shown (see Figure
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
Figure 32
See Figure 31 for recommended receptacle location.
2. If the refrigerator is not level, adjust the feet on the
corners of the unit as necessary (see Figure 33).
Turn Foot to Adjust
Figure 33
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
8 Install the Unit.
Figure 31
Installation Tip
SHOCK HAZARD — Electrical Grounding Required.
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
height of 1/8" less than the opening’s rear height. Shorten
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
• Never use an extension cord to connect power to
the unit.
Go on to 7 Level the Unit.
2115R — Refrigerator
Installation Troubleshooting
8 Install the Unit
Q: Problem
Installation of the 2115R
The door remains open unless it is pushed closed.
1. Plug in the power cord.
A: Solution
2. Gently push the unit into position. Be careful not to
entangle the electrical cord.
The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure the
closers (at the bottom of the hinge pin) are clean, greased
and installed correctly. Also, re-check leveling from front
to back of the unit and readjust if necessary. Make sure
that pivot plate is installed correctly.
3. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
Relocating the Shelves
Q: Problem
Both the glass shelves in the refrigerator and the inner
door shelves can be moved to accommodate your bottles,
cans and containers.
The custom overlay door was designed to align with the
rest of the cabinet doors, but the unit has crept forward.
A: Solution
Glass Shelves
1. Open door fully, grasp shelf firmly, lift front edge
slightly, and pull straight out.
Make sure that the electrical cord is not obstructing the
2. Choose new location and slide shelf onto the
appropriate rib.
Door Shelves
1. First pull shelf up at a 45°
angle, then straight out
(see Figure 34).
2. Choose new location and
line up on bosses. First
push straight in, then
down at a 45° angle.
Figure 34
2115R — Refrigerator
Start-Up Troubleshooting
9 Start-Up for the First Time
Initial Start-Up
Q: Problem
The unit is shipped with the control preset. No adjustments
should be necessary at this time. For information about
Adjusting the Temperature Control, see the Use and Care
A: Solution
Unit does not appear to turn on when POWER icon is
Make sure unit is plugged in and outlet has power (circuit
breaker has not tripped).
See the Use and Care Guide’s Troubleshooting Guide for
more solutions.
Who to Call
Service Information
If the need for service arises, call the U-Line Customer
Care Center directly @ 800-779-2547. To ensure accurate
assistance, please have your Model Number and Serial
Number and an explanation of the problem. The Model
and Serial Number plate is located inside unit at upper
right hand corner.
If you need to locate a service company, you can go online
at www.U-LineService.com and search for a service
company by zip code.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2006 U-Line Corporation
Publication No. 30146E
08/2006 Rev. B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF