Bowers Group MW Large Digitronic Workshop Caliper 150 Series Instruction Manual

Below you will find brief information for Caliper 150 Digitronic Workshop Caliper. The Caliper 150 Digitronic Workshop Caliper is a high-precision measuring tool that provides both absolute and relative measurement modes for accurate readings. It features a 0.01mm resolution and a 3m per second measuring speed for efficient measurements. This versatile caliper can measure in metric or imperial units and includes a data output port to connect to computers for recording measurement data.

PDF Download

Document

CALIPER INSTRUCTIONS

Large Digitronic Workshop Caliper 150 Series

Please carefully review these instructions to ensure proper and accurate use of your new Digitronic Caliper.

Electronics

Locking

Screw

Data

Output

Fine Adjustment

Slider Scale

Slider Battery

Cover

External Measuring Faces

Internal Measuring Faces

Function

ON/OFF: Power on/off switch

ABS/INC: Relative/absolute measurement

ZERO: Zero setting button mm/in: metric/inch conversion

SET: presetting button

HOLD: data hold button

Instructions

• Operating Condition:

Temperature: 5-40°C

• Prevent any liquid from contacting the protective sticker

• Never apply voltage (e.g. Engraving with an electrograph) on any part of this Caliper for fear of damaging the circuit

• Preset a starting point of measurement correctly (please refer to Operations).

Unless presetting, do not press the “SET” button purposely for fear of measurement error

Technical Specifications

• Resolution:

• Repeatability:

• Accuracy:

• Maximum measuring speed:

• Battery:

0.01mm / 0.0005"

0-600mm: +/-0.07mm

3m per second

CR 2032 3V Lithium Battery

Instructions of Data Output

• Preset zero and metric/inch system

• Connect the end of the interface cable to the computer. The other to the data output port of this Caliper

• Start this Caliper and software

• Move the slider to the position you want and press the button on control box for data output

• Battery life: approx. 1 year

Battery Replacement

Once display begins flashing or even no display, slide the cover open as the arrow shows and replace with a new battery (CR 2032)

Note:

• The positive pole of the battery must face out

• Please preset the starting point over again after battery replacement

For more information visit www.moore-and-wright.com Partners in Precision

MW150-DDL_Manual_A4.indd 1 21/05/2013 08:07

CALIPER INSTRUCTIONS

Operations

ON/OFF button

• Press ON/OFF button at any position when the power is off, this Caliper will be ready to work and display the measuring value

• Press ON/OFF at any position when the power is on, this Caliper will switch off

ABS/INC button

• Press ABS button in absolute mode (without “ABS” ), this Caliper is ready for absolute measurement

• Press ABS button in relative mode (with “ABS” displaying), this Caliper is ready for relative measurement and simultaneously displays “ABS”, showing relative mode

• Press ABS at any position for relative/absolute measurement interchange

ZERO button

• In relative mode, press ZERO button to set the current point to zero and this Caliper will display zero

• In absolute mode, press ZERO button to set the current point to the preset value and this Caliper will display this value mm/in button

• Press mm/in button at any position for metric/inch conversion

SET button and Internal Measuring (Easy one touch set)

• For presetting a starting point (the value has been preset to zero in the factory)

• With each one press on this button at any position, the current point is set to the preset value and displays on the LCD.

The details are as the follows:

Number of

Times Pressed

8 g

Preset Value

12.7mm / 0.5"

20.32mm / 0.8"

25.4mm / 1"

50.8mm / 2"

76.2mm / 3"

101.6mm / 4"

127mm / 5"

152.4mm / 6"

10mm / 0.3935"

20mm / 0.7870"

25mm / 0.9840"

50mm / 1.9685"

0 optional measuring optional measuring for optional measuring for optional measuring for optional measuring for optional measuring for optional measuring for optional measuring for optional measuring for internal measuring of 600mm calipers for optional measuring for optional measuring standard, after internal and optional measuring, please set for normal measuring

• The process is circulative. The preset value is held even after powering off

HOLD button

• Press “H” button at any position, this Caliper will hold the value as before and display “H” on the LCD.

The data will not change even if you move the slider

• Press “H” button once again to release hold state (no character “H” displays), then this Caliper displays the measured value

Restart this Caliper after powering off by pressing ON/OFF button, it will keep the last state (mm/in, ABS/INC,SET).

For more information visit www.moore-and-wright.com Partners in Precision

MW150-DDL_Manual_A4.indd 2 21/05/2013 08:07

Hello! I am an AI chatbot specifically trained to assist you with the Bowers Group MW Large Digitronic Workshop Caliper 150 Series Instruction Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

0.01mm resolution
absolute and relative measurement modes
metric and imperial units
3m per second measuring speed
data output port
preset starting point
data hold function
battery life: 1 year

Frequently asked questions

How do I set the starting point for measurement?

You can preset a starting point by pressing the "SET" button. The caliper will automatically set the current point to the preset value. You can choose from several preset values, including 12.7mm, 20.32mm, 25.4mm, 50.8mm, 76.2mm, 101.6mm, 127mm, 152.4mm, 10mm, 20mm, 25mm, 50mm, or 0.

What is the difference between absolute and relative measurement modes?

In absolute mode, the caliper will display the actual measurement value from the starting point. In relative mode, the caliper will display the difference between the current point and the starting point.

How do I connect the caliper to a computer?

You can connect the caliper to a computer using the data output port. Connect the end of the interface cable to the computer and the other end to the data output port of the caliper. Start the caliper and software, move the slider to the desired position, and press the button on the control box for data output.