Dual | XDVD710 | Owner`s manual | Dual XDVD710 Owner`s manual

XDVD710
INSTALLATION/OWNER’S MANUAL
DVD Multimedia Receiver with 7” Touch Screen Display
Safety Notes:
The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to
prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking
brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion.
Copyright Notes
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States
and or other countries.
All other trademarks are property of their respective owners.
XDVD710 PREPARATION
Table of Contents
Page
DVD Region Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation/Mounting/Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Locations - Monitor Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Locations - Monitor Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Locations - Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anti-theft Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AM/FM Tuner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MP3/WMA Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Media Compatibility Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4
5-7
8
9-10
11-12
13-14
15-20
21-22
23
24
25-28
29-30
31
32-39
40-42
43-44
45-46
47-48
49
50
51
DVD Region Management
Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the
XDVD710 plays discs according to their intentions, some functions may not work as intended. Please be sure to read
the instructions provided with each disc. This player has been designed to play back DVD software that has been
encoded for specific region areas. It cannot play back DVD software encoded for other region areas than the region
areas for which it has been designed.
The XDVD710 will play discs labeled “Region 1” or “All”.
DVD region codes:
1 - USA, Canada
2 - Japan, Europe, South Africa, Middle East
3 - Rep. of Korea, Taiwan, Hong Kong, Parts of Southeast Asia
4 - Australia, New Zealand, Mexico, South America
5 - Eastern Europe, Russia, India, Africa
6 - China
2
XDVD710 PREPARATION
WARNING
Upon installation of this Monitor/DVD player (“unit”) into a vehicle, the driver of the vehicle
must not operate this unit by watching videos or playing video games while driving.
Failure to follow this instruction could lead to driver distraction which could result in
serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or
property damage.
Several states prohibit the installation of monitors/DVD players if the screen is visible from
the driver’s seat. If you reside in a jurisdiction which has enacted such a law, this unit
must not be installed so that the screen is visible from the driver’s seat. When installing
this unit in the front console/dashboard, the unit must be positioned so that it is facing the
front passenger seat only. Failure to follow this instruction could lead to driver distraction
which could result in serious injury or death to the vehicle’s occupants or persons outside
the vehicle and/or property damage.
This unit is designed so that it may be operated only when the vehicle is in “Park” and the
parking brake is fully engaged. To this end, this unit includes a parking brake lock-out
feature which prohibits the unit from operating if the vehicle is not in “Park” and/or the
parking brake is not fully engaged. When installing this unit, the installer must connect
the parking brake detect wire (“Yellow-Blue Lead”) to the parking brake mechanism in
order to make the parking brake lock-out feature operable. DO NOT simply ground the
parking brake detect wire to a metal portion of the vehicle. Failure to properly install
the parking brake lock-out feature could lead to driver distraction which could result in
serious injury or death to the driver’s occupants or persons outside the vehicle and/or
property damage.
Once the parking brake lock-out feature is installed, the owner/user must not attempt to
disrupt/neutralize the parking brake lock-out feature by (a) partially engaging the parking
brake and/or (b) purchasing/using any device or unit designed to send necessary brake
signals to the unit. Failure to follow these instructions could lead to driver distraction
which could result in serious injury or death to the driver’s occupants or persons outside
the vehicle and/or property damage.
When operating this unit, keep the unit’s volume level low enough so that the vehicle’s
occupants can hear traffic-related sounds such as police and emergency vehicles.
Failure to follow this instruction could lead to driver distraction which could result in
serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or
property damage.
3
XDVD710 OPERATION
Safety Information
Please read all instructions carefully before attempting to install or operate.
Due to its technical nature, it is highly recommended that your DUAL XDVD710 is installed by a professional installer
or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only.
Safety Notes:
The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to
prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking
brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion.
To prevent damage or injury:
1. Make sure to ground the unit securely to the vehicle chassis ground.
2. Do not remove the top or bottom covers of the unit.
3. Do not install the unit in a spot exposed to direct sunlight or excessive heat or the possibility of water splashing.
4. Do not subject the unit to excessive shock.
5. When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may
cause the unit to malfunction.
6. To prevent short circuits when replacing a fuse, disconnect the wiring harness first.
7. Use only the provided hardware and wire harness.
8. You cannot view video while the vehicle is moving. Find a safe place to park and engage the parking brake.
9. If you experience problems during installation, consult your nearest DUAL dealer.
10.If the unit malfunctions, reset the unit as described on page 12 first. If the problem still persists, consult your
nearest DUAL dealer or call tech assistance @ 1-866-382-5476.
11.To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents
such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing.
12.When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker than
usual. Normal brightness will return after using the monitor for a while.
Additional Notes:
1.When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables
with an area of 0.75mm (AWG 18) or more to prevent voltage drops.
2.Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be hazardous
to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap
immediately.
This device complies with part 15 of the FCC rules and regulations.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
4
XDVD710 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it
would be subject to dust, dirt or excessive vibration.
Getting Started
•Slide the unit out of the mounting sleeve.
•Install mounting sleeve into opening, bending tabs to secure.
•Connect wiring harness and antenna as shown on pages 6-7. Consult a qualified technician if you are unsure.
•Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
•Test for correct operation and slide unit into mounting sleeve.
• Attach unit to mounting sleeve using supplied #1 Phillips screws.
•Snap trim ring into place.
•Mount the iplug™ adapter to any smooth clean surface using the supplied double-sided tape or Phillips head
screws.
Mounting sleeve opening dimensions
7-3/16” x 2-1/16” (183 mm x 53 mm)
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
5
XDVD710 INSTALLATION
Expanded Wiring Diagram - Inputs/Outputs
Wiring Notes:
Subwoofer output
The SUBWOOFER audio output (Blue RCA) is active in all audio modes and must be connected to an external
amplifier.
Rear view camera
A rear view camera (not included) can be used with the CAMERA input.
NEED HELP??
Call our Technical Service Hotline, 1-866-382-5476.
Safety Notes:
The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to
prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking
brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. Altering or
defeating this safety feature is a violation of law and is prohibited.
6
XDVD710 INSTALLATION
Wiring Diagram - Optional A/V Connections
7
XDVD710 OPERATION
IR Remote Preparation
To first use the IR Remote control,
you must first pull the battery
insulation tape out
Notes:
• Remove the battery if the remote will
not be used for a month or longer
• Remove and dispose of battery properly
Insert or replacing the Battery:
Remove the battery holder
Remove the battery from the battery
holder
Install the new battery
Make sure to keep the (+) side up
Insert the battery holder
CAUTION!!!
• Do not store battery with metallic
objects or materials
8
XDVD710 OPERATION
Control Locations - Monitor Closed
1
2
4
3
5
6
16
15
14
13
12
11
10
9
8
7
Play/Pause/Scan
1
Band
9
2
Auto Store/Preset Scan
10 Stop
3
Secondary LCD
11 Chapter/Track Up
4
Display
12 Chapter/Track Down
5
Open/Close Monitor
13 Fast Forward
6
Eject
14 Fast Reverse
7
Rotary Encoder/Enter
15 Mute
8
Mode
16 Power/Volume
Monitor Notes:
• This model incorporates a motorized moving monitor. Before final installation, make sure the monitor will
not obstruct the dash, shifter or any other controls.
• Upon installation, do not attempt to move the monitor up/down by hand. Use the ANGLE / and OPEN
buttons on the front panel only.
• The unit will stop if it encounters any obstacles during the open/close sequence. If this occurs, remove the
obstacle and press OPEN again to resume the monitor open/close sequence.
9
XDVD710 OPERATION
Control Functions - Monitor Closed
BAND
AS/PS
(Auto Store /Preset Scan)
SECONDARY LCD
Press BAND to increment from FM1, FM2, FM3, AM1] FM1.
Press AS/PS momentarily to start station PRESET SCAN function,
Press AS/PS for 2 seconds to start AUTO STORE station preset function in
current BAND.
Additional LCD for system information while monitor is closed.
DISP
Press the DISP button to display various information on the secondary LCD.
OPEN
Press OPEN to open or close the monitor. The unit will emit 1 confirmation
beep upon opening, 3 beeps when closing. Be careful not to not touch
or obstruct the monitor movement during the open/close sequence, or
permanent damage could occur.
EJECT
Press once to eject disc.
ROTARY
MODE
TRACK UP
TRACK DOWN
STOP
PLAY/PAUSE
Rotate clockwise/counter-clockwise to select desired item and press once to
ENTER.
Press once to incrementally select desired source.
Selects the next chapter/track for playback.
Selects the previous chapter/track for playback.
Stop playback of DVD/CD/MP3.
Press once for PAUSE, press again for PLAY.
FAST FORWARD
Fast forward the content.
FAST REVERSE
Fast reverse the content.
MUTE
POWER ON/OFF
VOLUME
Press once to MUTE audio, MUTE will appear in the secondary LCD. Press
again to return audio.
Press POWER momentarily to turn the unit on, the unit will beep 2 times.
Press and hold POWER for more than 2 seconds, unit will beep 1 time, then
turn off. Note: EJECT will still function even if POWER is off.
Rotate clockwise/counter clockwise for desired VOLUME level,
10
XDVD710 OPERATION
Control Locations - Monitor Open
1
2
3
4
5
1 Disc-in indicator - Red = Disc inserted, White = No disc.
2 ANGLE  - Press to decrease the monitor view angle.
3 ANGLE  - Press to increase the monitor view angle.
4 INFO - Press to select DVD INFO and press and hold for BRIGHTNESS.
5 Press to RESET system.
Safety Notes:
The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to
prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking
brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion.
11
XDVD710 OPERATION
Control Functions - Monitor Open
Disc-in indicator
Monitor Angle pq
White = No disc
Red = Disc inserted
Press ANGLE p to increase the monitor view angle.
Press ANGLE q to decrease the monitor view angle.
Notes:
• Do not attempt to move the monitor up/down by hand - severe damage will
occur. Use the front panel buttons or the remote control only.
• The color of the LCD monitor varies between viewing angles. Select the angle
with the most optimum view for your location.
• The last position of the monitor will be saved in memory. The monitor will
return to its last position automatically the next time it is opened.
INFO/PIC
Press INFO button for 1 second to display DVD disc information.
Press and hold INFO for 2 seconds to change TFT LCD BRIGHTNESS:
Press ANGLE p to increase, ANGLE q to decrease or use VOLUME rotary to
adjust the level up or down, (0 minimum/20 maximum), 10 is default.
SYSTEM RESET
If you experience abnormal operation or, your unit is inoperable, press the
RESET button for 3 seconds, located on the front bottom-right corner of the unit.
After a system reset, the unit restores all factory default settings.
Note: Use the tip of a pen to access the button.
12
XDVD710 OPERATION
Control Locations - Remote
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
Mode
16 Info
31 Root
2
Mute
17 Search
32 Repeat
3
Open/Close
18 Key #0
33 Chapter/Track Down
4
Power
19 Band/Stop
34 Chapter/Track Up
5
Key #1
20 Audio Select
35 Fast Rewind
6
Key #2
21 Escape
36 Fast Forward
7
Key #3
22 4-Way - Up
37 Zoom
8
Volume Up
23 Menu
38 Audio
9
Key #4
24 Picture
39 Angle
10 Key #5
25 4-Way - Left
40 Sub-Title
11 Key #6
26 Ok
12 Volume Down
27 4-Way - Right
13 Key #7
28 Repeat A-B
14 Key #8
29 Title Menu
15 Key #9
30 4-Way - Down
* The remote control uses one 3 volt Lithium CR2025 battery. For best performance, replace only with CR2025 or equivalent.
13
XDVD710 OPERATION
Control Functions - Remote
Mode
Press once to incrementally select desired source.
Mute
Press once to MUTE audio, press again to return audio.
Open/Close
Power
Keys 0-9
Volume Up
Volume Down
Info
Search
Band/Stop
Audio Select
Escape
4-Way -Up/Down/Left/Right
Menu
Picture
Ok
Repeat A-B
Title Menu
Root
Repeat
Chapter/Track Down
Chapter/Track Up
Press once to open monitor, press again to close the monitor.
Press once to turn the unit on, press again to turn unit off.
Direct access chapter/track/preset station for current BAND.
Increase VOLUME.
Decrease VOLUME.
Displays DVD information.
Search function in the DVD/CD disc mode.
Press to increment BAND, or STOP while in DVD/MP3 mode.
Enter AUDIO Setup mode.
Exit current menu.
Navigating system and DVD menus.
Enter the MAIN system menu.
BRIGHTNESS parameter setting for TFT.
Starts/pauses playback or confirm settings.
Repeat playback from time frame A to time frame B.
Enters the title menu on DVD.
Enters the main menu of the DVD.
Repeats playback of current chapter/track or folder.
Selects the previous chapter/track for playback.
Selects the next chapter/track for playback.
Fast Rewind
Fast reverses the disc content.
Fast Forward
Fast forwards the disc content.
Zoom
Zooming in/out on an image from DVD disc.
Audio
Change the audio language for DVD disc playback.
Angle
Selects between different angles (when available) for a scene.
Sub-Title
Language selection for subtitle.
14
XDVD710 OPERATION
General Operation
Power On/Off
Monitor Open/Close
Press POWER momentarily to turn the unit on, the unit will beep 2 times.
Press and hold POWER for more than 2 seconds, unit will beep 1 time, then
turn off. Note: EJECT will still function even if POWER is off.
Press OPEN to open or close the monitor. The unit will emit 1 confirmation
beep when opening, 3 beeps when closing. Be careful not to not touch the
monitor during the open/close sequence.
Notes:
• The unit will stop automatically during open/close if an obstacle is detected.
If this occurs, remove the obstacle and press OPEN again to resume the
monitor open/close sequence.
• Audio can be heard while the monitor is closed.
Monitor Angle Position
Press ANGLE p to increase the monitor view angle.
Press ANGLE q to decrease the monitor view angle.
Notes:
• Do not attempt to move the monitor up/down by hand - severe damage will
occur. Use the front panel buttons or the remote control only.
• The color of the LCD monitor varies between viewing angles. Select the
angle with the most optimum view for your location.
• The last position of the monitor can be saved in memory. The monitor will
return to its last position automatically the next time it is opened.
Notes:
• The vehicle must be in park and the parking brake applied to view video on
the in-dash monitor.
• As a safety feature, a blue “CAUTION” screen will show on the display when
the vehicle's parking brake is not engaged. DVD, AV1 audio can be heard
while the vehicle is in motion.
• The video display of the in-dash unit will not operate while the vehicle is
moving. This is a safety feature to prevent driver distraction. In-dash video
functions will only operate when vehicle is in Park and the parking brake
is engaged. It is illegal in most states for the driver to view video while the
vehicle is in motion. Refer to local laws in your area.
See DVD operation on page 32 for more details on how to initialize the
PARKING BRAKE.
15
XDVD710 OPERATION
General Operation
Mode
Optional Mode Selection
Volume
Mute
Audio Adjustment
from front panel
Press MODE to select between TUNER, DVD, AUX IN, and CAMERA inputs.
Modes of operation are indicated in the OSD (On Screen Display) and
secondary LCD.
With the monitor open, press the top left corner of the screen to display the
OSD menu. Press TUNER, DVD, AUX IN or CAMERA icon to select the desired
source.
Adjust VOLUME using rotary encoder or the VOL   buttons (00-40).
Press MUTE to silence the audio;
Press MUTE again to cancel.
will appear in the OSD.
Press in VOLUME rotary knob on left front panel,
Press in VOLUME again to advance to desired parameter to be changed,
Turn VOLUME rotary Q or P to adjust to desired level,
Press in VOLUME to advance to next selection,
Press and hold the VOLUME button on the front panel to exit.
ITEM
00
00
EQ
00 R
F
00 L
R
00
L
Audio Adjustment
from Remote
RANGE
USER
FLAT
JAZZ
POP
CLASSIC
ROCK
NEWS
URBAN
MOVIE
RAVE
TECHNO
BASS
-7
+7
TREBLE
-7
+7
FADE
-7
+7
BALANCE
-7
+7
SUB
-7
+7
OFF
ON
LOUD
Press the SEL button,
Press the p q buttons on the remote to select an item to be adjusted,
Press  or  to adjust the desired setting,
Press the ESC button on the remote control to exit the audio control menu.
Notes: The Bass and Treble levels are only adjustable when EQ is set to
"User” mode. The Loud function compensates for deficiencies in sound
ranges at low levels. When the Loud function is on, LOUD is displayed on the
screen.
16
XDVD710 OPERATION
General Operation
INFO/PIC
RGB BRIGHTNESS
CVBS Screen Controls
SHARPNESS
CONTRAST
COLOR
BRIGHTNESS
TINT
Note: Adjustments to
SHARPNESS, CONTRAST,
COLOR, BRIGHTNESS & TINT
are only possible while in
either AUX-IN or CAMERA
CVBS mode.
Press INFO button for 1 second to display DVD disc information.
Press and hold INFO for 2 seconds to change TFT LCD BRIGHTNESS:
Press ANGLE p to increase, ANGLE q to decrease, or use VOLUME rotary to
adjust the level up or down. (0 minimum/20 maximum) 10 is default.
While in AUX IN or CAMERA mode:
Press and hold INFO for 2 seconds to access PICTURE MENU, press INFO briefly
again to step to next selection:
PICTURE MENU
[SHARPNESS
[CONTRAST
[COLOR
[BRIGHTNESS
[TINT
10
10
10
10
10
L
Press q or p to adjust the sharpness (0 minimum/+20 maximum).
Press q or p to adjust the contrast (0 minimum/+20 maximum).
Press q or p to adjust the color (0 minimum/+20 maximum).
Press q or p to adjust the brightness (0 minimum/+20 maximum).
Press q or p to adjust the tint (0 minimum/+20 maximum).
17
XDVD710 OPERATION
General Operation
BAND
Press BAND to increment from FM1, FM2, FM3, AM1] FM1.
AS/PS
(Auto Store /Preset Scan)
Press AS/PS momentarily to start station PRESET SCAN function. The unit
will now scan your program presets for 10 seconds for each preset in that
band. Press AS/PS again to stop scanning. Press AS/PS for 2 seconds to
start AUTO STORE station preset function in current BAND.
DISP
Press the DISP button to display various information on the secondary LCD
screen when the monitor is closed.
OPEN
Press OPEN to open or close the monitor. The unit will emit 1 confirmation
beep upon opening, 3 beeps when closing. Be careful not to not touch
or obstruct the monitor movement during the open/close sequence, or
permanent damage could occur.
EJECT
Press once for DISC ejection.
ROTARY
MODE
TRACK UP
TRACK DOWN
STOP
PLAY/PAUSE
Press to access MAIN menu, rotate clockwise/counter-clockwise to select
desired item and press once to ENTER.
Press once to incrementally select desired source.
Selects the next chapter/track for playback.
Selects the previous chapter/track for playback.
Stop playback of DVD/CD/MP3.
Press once for PAUSE, press again for PLAY.
FAST FORWARD
Fast forward the disc content.
FAST REVERSE
Fast reverse the disc content.
MUTE
Press once to MUTE audio, press again to return audio, an icon indicator will
flash on the TFT monitor.
POWER ON/OFF
Press POWER momentarily to turn the unit on, the unit will beep 2 times.
Press and hold POWER for more than 2 seconds, unit will beep 1 time, then
turn off. Note: EJECT will still function even if POWER is off.
VOLUME
PROGRAMMABLE TURN-ON
VOLUME
Rotate VOLUME rotary knob Q or P for desired VOLUME level, press once to
access the AUDIO SETUP MENU.
Turn VOLUME rotary to desired listening level, press and hold VOLUME
rotary knob for 3 seconds to program currently selected volume level.
18
XDVD710 OPERATION
General Operation
Secondary LCD Information
1
2
3
4
Note: Secondary LCD only functions when TFT monitor is closed.
1) LOC
2) ST
3) TIME
4) LOUD
19
LOCAL indicator, icon will be off when DISTANCE (DX) is selected
STEREO radio station indicator
Displays TRACK time, TUNING frequency, MP3 ID3 info, & CLOCK, etc
LOUDNESS selection indicator
XDVD710 OPERATION
General Operation
Main Menu Access
There are three methods to access the MAIN menu
• Press the ENTER button on the right ROTARY knob
• Press the MENU button on the remote control
• Touch the upper left corner of the touch screen
1
3
2
10
9
8
L
7
6
Touch Access Buttons
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Rapid Dial
5
4
Touch to access AM/FM TUNER mode
Touch to access CD/DVD mode, (CD/DVD must be inserted)
Touch to RETURN to previous screen
Touch to access CAMERA mode, if optional camera isn't connected then
"No Video Signal" will be displayed
Touch to STANDBY screen, touch screen again or any button to resume display
Note: VOLUME level can be controlled in STANDBY mode
Touch to access AUXILIARY A/V INPUT mode
Touch to access SCREEN SETUP menu
Touch to access GENERAL SETUP menu
Touch to access CD/DVD SETUP menu, (CD/DVD must be inserted to function)
Touch to access MAIN Source menu
RAPID DIAL can also control touch screen functions from the main menu
• Select desired function rotating clockwise or counter-clockwise
• Function will be outlined in yellow
• Press to confirm/ENTER
20
XDVD710 OPERATION
GENERAL Setup - Menu
General Setup Menu
L
Note:
Default anti-theft password
is 0000
Settings
Default
Radio
USA
Clock adjust
Clock Mode
AM
12Hr
Camera Image
Normal
Video Format
Auto
TFT Auto Open
Off
Anti-theft Code
Anti-theft active
0000
Off
• Press the GENERAL button to access the GENERAL setup mode
• Select desired parameter you wish to change
• Page will return back to previous screen after 10 seconds of inactivity or
by pressing the RETURN button
GENERAL Setup Menu matrix
Options
USA
S-Amer1
S-Amer2
Europe
00:00
12Hr
24Hr
Normal
Reverse
Auto
NTSC
PAL
On
Off
Manual
---On
Function
Set to appropriate setting for your country
See adjusting the clock on page 23 for more details
PM 6:00
18:00
Normal Image
Mirror camera input image 180 degrees
System will auto detect NTSC or PAL
For NTSC compatibility
For PAL compatibility
TFT panel will automatically open when IGN is turned on
TFT panel will not auto open when IGN is turned on
TFT will only open/close when OPEN button is pressed
Must enter password to turn anti-theft on or off
System will require a password if main battery power is
removed for more than 5 minutes
No password will be required if power is removed
Load all factory parameters to their original settlings,
Note: This will not reset the anti-theft password.
Off
Load Factory
Yes
Are you
defaults
sure?
Yes/Cancel
Note: Not all GENERAL setup features are described in detail.
21
XDVD710 OPERATION
GENERAL Setup - Adjusting Radio Frequency
Adjusting Radio Frequency
L
1
Step 1
1) Touch top left corner of screen
L
2
Step 2
2) Touch GENERAL setup button
L
3
Step 3
3) Touch USA
L
L
5
4
Step 4
4) Touch the setting for your region
Step 5
Touch RETURN to exit
22
XDVD710 OPERATION
GENERAL Setup - Adjusting the Clock
12Hr Clock Mode
L
1
Step 1
1) Touch top left corner of screen
L
2
Step 2
2) Touch GENERAL setup button
L
3
Step 3
3) Touch 00:00 area in the CLOCK row
L
7
L L L
8
5
6
Steps 4-8
4) Keypad should now appear
5) Enter HOURS, touch ok
6) Enter MINUTES, touch ok
7) Touch AM or PM to set
8) Touch RETURN to exit
24Hr Clock Mode
23
If you desire 24Hr format, select 24Hr from CLOCK MODE, then follow steps 1-8.
XDVD710 OPERATION
GENERAL Setup - Setting the Anti-theft code
By default Anti-theft password is 0000
and is turned Off. To turn this
feature on, follow the steps below.
CAUTION!!
This will lock your unit from operating
if battery POWER is disconnected for
more than 5 minutes.
Step 1 & 2
L
1
L
2
1) Touch top left corner of screen
2) Touch GENERAL Setup button
L
4
Step 3 & 4
L
3
3) Touch down arrow button
4) Touch ----
L
6
Step 5 & 6
Note: it is
recommended that
you choose your own
4-digit password
Step 7 & 8
carefully, write it down
somewhere and keep
in a safe location. In
the event you ever
loose or forget your
password, call our tech
hot line for support
on how to unlock your
system.
Step 9 & 10
5) Enter 0000, then press ok
L
5
L
6) Touch OFF
L
8
7
7) Touch ON
L
9
8) Touch ---- again
9) Enter your new 4-digit password,
then press ok.
10
L
10) Touch RETURN to exit
24
XDVD710 OPERATION
SCREEN Setup - Menu
Screen Setup Menu
L
• Press the SCREEN button to access the SCREEN setup mode
• Select desired parameter you wish to change
• Page will return back to previous screen after 10 seconds of inactivity or by
pressing the RETURN button
SCREEN Setup Menu matrix
Settings
Default
Options
Brightness
10
0 - 20
Screen Tilt
Screen Saver
4
On
TS Calibrate
No
1-6
Off
On
No
Yes
Version
Function
Press the  or  buttons on the remote or press the right
rotary once and rotate clockwise/counter-clockwise to adjust
the BRIGHTNESS to the desired setting
Select 1 to 6 to adjust the default tilt angle of the screen
Select On to activate the screen saver, Off to deactivate
Touch Yes to enter the Touch Screen calibration mode
Software version of unit
System Standby
L
To conserve the LCD backlight lifespan or to eliminate glare while night driving,
press STANDBY. The TFT screen will black out, however all other operations
continue to operate. Press any button except VOLUME or touch the screen again
to return to normal viewing.
25
XDVD710 OPERATION
SCREEN Setup - Setting TFT Brightness
This will set the default setting
for the TFT display brightness.
This can also be set by
pressing the INFO button on
the front TFT panel.
Step 1
Step 2
L
1
1) Touch top left corner of screen
L
2
2) Touch SCREEN setup button
L
3
Step 3
3) Touch [-] to dim TFT
L
L
5
4
Step 4
4) Touch [+] to brighten TFT
0 - 20 is possible
Default = 10
Step 5
5) Touch RETURN to exit
26
XDVD710 OPERATION
SCREEN Setup - Setting TFT Angle
Set for best viewing angle in
your vehicle
L
1
Step 1
1) Touch top left corner of screen
Step 2
L
2
2) Touch SCREEN setup button
L
3
Step 3
3) Touch a number displayed in SCREEN TILT row
L
L
5
4
Step 4
4) Touch desired angle for best viewing angle
1 - 6 is possible
Default = 4
Step 5
27
5) Touch RETURN to exit
XDVD710 OPERATION
SCREEN Setup - Touch Screen Calibration
On occasion, the touch screen will
have to be calibrated. Follow these
steps as described.
L
1
Step 1
1) Touch top left corner of screen
Step 2
L
2
2) Touch SCREEN setup button
LL
3
Step 3 & 4
4
3) Touch No in TS Calibration row
4) Then touch Yes
L
5
Note: For proper calibration
you must touch each pointer for
2 seconds. If pointers are not
touched properly, the calibration
sequence will start over until the
calibration is done correctly.
Step 5 & 6
5) Touch and hold the pointers as indicated on the screen for 2 seconds each
6) Screen will automatically return to MAIN MENU, touch RETURN to exit
28
XDVD710 OPERATION
AM/FM Tuner Operation
AM/FM Tuner TFT Display
2
1
3
4
19
5
18
6
L
17
16
15
29
14
13
12
11
7
10
9
8
1)
Current MODE information, touch upper left area to return to MAIN MENU
2)
Current PRESET station indicator
3)
STEREO broadcast indicator
4)
Clock
5)
PRESET page up
6)
LOCAL/DISTANCE selection
7)
PRESET page down
8)
Auto station SCAN button
9)
MANUAL TUNE up
10)
MANUAL TUNE down
11)
SEEK TUNE up
12)
SEEK TUNE down
13)
AS/PS (AUTO STORE/PRESET SCAN)
14)
BAND selection, FM1, FM2, FM3, AM
15)
VOLUME indicator
16)
LOUD indicator
17)
Equalizer indicator, touch to access AUDIO Setup menu
18)
Current radio frequency indicator
19)
Current radio BAND indicator
XDVD710 OPERATION
AM/ FM Tuner Operation
Auto Seek Tuning
Manual Tuning
Auto Store (AS)
Press the
button to auto SEEK up the next strongest station.
Press the
button to auto SEEK down the next strongest station.
Press the
button to manually tune up one step at a time.
Press the
button to manually tune down one step at a time.
Press and hold AS/PS for more than 2 seconds to automatically store the
twelve strongest stations in the current band. Automatic Local tuning is
activated during the initial band scan, repeat for other bands.
Note: All presets within the current band will be overwritten.
Program Scan (PS)
Press AS/PS for less than 2 seconds to scan presets 1-12 on the current
band, pausing for 10 seconds at each. Press AS/PS again to cancel.
SCAN
Press SCAN to preview strong stations on the current band, pausing for 10
seconds at each station. Press SCAN again to cancel.
LOC/DX Radio Station
Touch LOC button on the TFT to activate LOC/DX tuning.
When the LOCAL function is on, LOC will appear. Only radio stations with a
strong signal are received. DISTANCE (DX) is for radio stations that are far
away and/or have weak signals.
Storing Radio Stations
PRESET
Up to 36 FM stations and 12 AM stations can be stored. To store a station,
select the desired band and station. Press and hold the desired preset button
(1-12) for more than 2 seconds. When stored, the PRESET number will
appear in the display. The station can be recalled anytime by pressing the
corresponding preset button on the TFT.
Recalling a Radio Station PRESET
PRESET Page
Up/Down
Touch a corresponding radio frequency for less than 2 seconds to recall.
Only 6 PRESETS can be display at one time, use PRESET page up/down to
access next stored PRESETS accordingly.
L
30
XDVD710 OPERATION
WARNING
Upon installation of this Monitor/DVD player (“unit”) into a vehicle, the driver of the vehicle
must not operate this unit by watching videos or playing video games while driving.
Failure to follow this instruction could lead to driver distraction which could result in
serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or
property damage.
Several states prohibit the installation of monitors/DVD players if the screen is visible from
the driver’s seat. If you reside in a jurisdiction which has enacted such a law, this unit
must not be installed so that the screen is visible from the driver’s seat. When installing
this unit in the front console/dashboard, the unit must be positioned so that it is facing the
front passenger seat only. Failure to follow this instruction could lead to driver distraction
which could result in serious injury or death to the vehicle’s occupants or persons outside
the vehicle and/or property damage.
This unit is designed so that it may be operated only when the vehicle is in “Park” and the
parking brake is fully engaged. To this end, this unit includes a parking brake lock-out
feature which prohibits the unit from operating if the vehicle is not in “Park” and/or the
parking brake is not fully engaged. When installing this unit, the installer must connect
the parking brake detect wire (“Yellow-Blue Lead”) to the parking brake mechanism in
order to make the parking brake lock-out feature operable. DO NOT simply ground the
parking brake detect wire to a metal portion of the vehicle. Failure to properly install
the parking brake lock-out feature could lead to driver distraction which could result in
serious injury or death to the driver’s occupants or persons outside the vehicle and/or
property damage.
Once the parking brake lock-out feature is installed, the owner/user must not attempt to
disrupt/neutralize the parking brake lock-out feature by (a) partially engaging the parking
brake and/or (b) purchasing/using any device or unit designed to send necessary brake
signals to the unit. Failure to follow these instructions could lead to driver distraction
which could result in serious injury or death to the driver’s occupants or persons outside
the vehicle and/or property damage.
When operating this unit, keep the unit’s volume level low enough so that the vehicle’s
occupants can hear traffic-related sounds such as police and emergency vehicles.
Failure to follow this instruction could lead to driver distraction which could result in
serious injury or death to the vehicle’s occupants or persons outside the vehicle and/or
property damage.
31
XDVD710 OPERATION
DVD Operation - Parking Brake Initialization
SAFETY WARNING
CAUTION !!!
IT'S UNLAWFUL TO OPERATE
A VEHICLE WHILE VIDEO IS
DISPLAY IN THE DRIVERS
VIEWING AREA
ENGAGE EMERGENCY BRAKE
TO ENJOY VIDEO
Front TFT Video Initialization
• The video display of the in-dash unit will not operate while the vehicle is
moving. This is a safety feature to prevent driver distraction. In-dash video
functions will only operate when vehicle is in Park and the PARKING BRAKE
is engaged. It is illegal in most states for the driver to view video while the
vehicle is in motion. Refer to local laws in your area.
• Audio can be heard while the monitor is closed.
• The vehicle must be in park and the parking brake applied to view video on the
in-dash monitor.
• As a safety feature, “ENGAGE PARKING BRAKE” blue screen will show on
the display when the vehicle's parking brake is not engaged. Video display
on the front monitor isn't allowed until the PARKING BRAKE is engaged. By
connecting the yellow/blue PARKING BRAKE wire to brake switch circuit as
described below, DVD and AV1 audio can be heard while the vehicle is in
motion without engaging the parking brake.
Follow these two initialization procedures carefully to allow video playback on
XDVD710 front panel TFT:
There are two situations that start the PARKING BRAKE sequence.
Parking Brake Initialization
Situation 1
First situation is while driving:
1) Stop vehicle, put in Park, make sure PARKING BRAKE is off/released
2) Depress PARKING BRAKE for 1 second
3) Release PARKING BRAKE for 1 second
4) Depress PARKING BRAKE permanently
Note:
Once above procedure 1-4 is completed, video will display in approximately 6
seconds.
Parking Brake Initialization
Situation 2
Second situation is while already parked and the PARKING BRAKE is already
applied:
1) Keep vehicle in Park, PARKING BRAKE should be on
2) Release PARKING BRAKE for 1 second
3) Depress PARKING BRAKE for 1 second
4) Release PARKING BRAKE for 1 second
5) Depress PARKING BRAKE permanently
Notes:
Once 2nd procedure 1-5 is completed, video will display in approximately 6
seconds. The transition time must be less than 2 seconds between depress and
release.This procedure will have to repeated if the IGN is turned off.
32
XDVD710 OPERATION
DVD Operation
DVD Region Management
Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the
XDVD710 plays discs according to their intentions, some functions may not work as intended. Please be sure to read
the instructions provided with each disc. This player has been designed to play back DVD software that has been
encoded for specific region areas. It cannot play back DVD software encoded for other region areas than the region
areas for which it has been designed.
The XDVD710 will play discs labeled “Region 1” or “All”.
DVD region codes:
1 - USA, Canada
2 - Japan, Europe, South Africa, Middle East
3 - Rep. of Korea, Taiwan, Hong Kong, Parts of Southeast Asia
4 - Australia, New Zealand, Mexico, South America
5 - Eastern Europe, Russia, India, Africa
6 - China
DVD Disc Symbols
Notes:
Some DVD discs can be
played only in certain playback
modes according to the
intentions of the software.
As the XDVD710 plays discs
according to their intentions,
some functions may not work
as intended. Please be sure to
read the instructions provided
with each disc.
33
XDVD710 OPERATION
DVD Operation - Inserting a Disc
DVD Loading Slot
Eject button
Insert CD/DVD with label facing upwards
Inserting a Disc
When inserting a DVD disc, usually it will play automatically. Other
sub-menus may have to be pressed to access the DVD movie/music content.
Read the directions of your specific DVD disc for other features.
Note: If PARENTAL Lock is activated and the disc inserted is not authorized,
a 4-digit code must be entered and/or the disc be authorized. See "RATING
MENU" on page 42.
Note: Only one disc can be inserted at a time.
Ejecting the Disc
Resetting the Loading Mechanism
Press the EJECT button.
If the disc loads abnormally or an system error occurs, press and hold the
eject button for 3 seconds to reset the loading mechanism. The disc will eject
and normal operation should resume.
34
XDVD710 OPERATION
DVD Operation - Touch Screen Controls
Hidden Touch Screen area
while in TUNER mode
There are several hidden TOUCH SCREEN areas outlined below:
"A" area can be used in any mode to access MAIN menu
L
Hidden Touch Screen areas
while in DVD mode
"A-F" areas can be used in DVD mode to access:
A - Displays MAIN menu
B - Displays DVD track information
C - Selects PREVIOUS chapter
D - Selects NEXT chapter
E - Displays the full DVD transport controls
F - GOTO search menu
L
35
XDVD710 OPERATION
DVD Operation - Touch Screen Controls
Using the hidden Touch Screen
Controls
A - Displays MAIN menu
B - Displays DVD track
information
C - Selects PREVIOUS chapter
D - Selects NEXT chapter
E - Displays the full DVD
transport controls
F - GOTO search menu
L
L
AREA A
Access MAIN Menu
AREA B
Displays Track Information
AREA C
Selects PREVIOUS Track
AREA D
Selects NEXT Track
Note:
A DVD disc must be inserted
to access these functions and
features.
L
L
L
L
AREA E
Full DVD Transport Controls
AREA F
DVD Search
36
XDVD710 OPERATION
DVD Operation - Touch Screen Controls
Using the hidden Touch
Screen Controls
DVD Transport Control OSD
L
Touch AREA E
1)
Touch the
PLAY button or on the front panel to resume disc playback
2)
Touch the
PAUSE button again to suspend the disc playback
3)
button to STOP playback, touch
Touch
resume playback
4)
Touch the
REVERSE button to FAST REVERSE on DVD, 2x, 4x, 8x to 20x
5)
Touch the
FORWARD button to FAST FORWARD on DVD, 2x, 4x, 8x to 20x
6)
Touch the
REPEAT to scroll through the following:
or ok on the remote to
DVD: Repeat Title, Repeat Chapter, Repeat Off
A) Use the A-B function to define a specific area of disc to repeat.
Press the Repeat A-B button to set a start point of the (A) selection.
B) Press the A-B button again once you reach the desired end point (B) of the
repeated section. The selected portion of the DVD will now repeat continuously.
C) Press A-B button once again to cancel the A-B selection and stop repeat
playback.
37
7)
Touch to change Audio language playback
8)
Touch to change Subtitle of DVD
9)
Touch to return to DVD MAIN menu
XDVD710 OPERATION
DVD Operation - Searching a DVD
Searching a DVD
L
Searching by Time, Title
or Chapter
Touch the top right screen - AREA F
Search by TIME example
1) Touch the
in the TIME area
2) A touch keypad will now appear, enter your desired TIME to search
3) Press ok
Notes:
Some DVD discs can be played only in certain playback modes
according to the intentions of the software. As the XDVD710 plays discs
according to their intentions, some functions may not work as intended.
Please be sure to read the instructions provided with each disc.
38
XDVD710 OPERATION
DVD Operation
Direct Chapter / Track Selection
During DVD and CD playback, you can use the numeric keypad on the remote
control to access tracks directly.
Viewing an Alternate picture
Angle
(DVD only)
Some DVD's contain scenes that have been shot simultaneously from
different angles. For discs recorded with multiple angles, press the ANGLE
button on the remote control to toggle between available angles.
Multi-Language Disc
If you are watching a disc recorded in multiple languages, press the AUDIO
button on the remote control to choose your desired language. You can also
touch AREA E and use the
Changing Subtitle Language
button to change languages.
If you are watching a disc recorded in multiple languages with subtitles,
press the SUB-T button on the remote control to choose your desired subtitle,
You can also touch AREA E and use the
DVD Playback Information
button to change subtitles.
During playback, press the INFO button on the remote control or touch AREA
B to display the DVD playback information on screen.
The following information will be displayed:
Playback Information
39
1)
Indicates current source playing
2)
Indicates the fourth of sixteen titles on the DVD is currently playing
3)
Indicates the first of twenty chapters on the DVD is currently playing
4)
Indicates the playback time of the current title
5)
Indicates the USER defined EQ levels
6)
Indicates the LOUD setting is on
7)
Indicates the current time
XDVD710 OPERATION
DVD Setup Menu - Language
LANGUAGE Setup Menu
Note:
A DVD disc must be inserted
to access these functions and
features.
With the monitor open in DVD mode, press the AREA A (top left screen) to display
the MAIN menu. Press DVD Setup to access the DVD setup menu.
L
L
Press LANGUAGE icon to select LANGUAGE setup page
Disc Subtitle
Press to select desired disc subtitle language
L
Audio Language
L
Press to select desired disc audio language
L
DVD Menu
English
French
Spanish
Auto
Off = DEFAULT
English = DEFAULT
French
Spanish
Press to select desired disc menu language
English = DEFAULT
French
Spanish
L
40
XDVD710 OPERATION
DVD Setup Menu - Video
Video Setup Menu
Note:
A DVD disc must be inserted
to access these functions and
features.
With the monitor open in DVD mode, press the AREA A (top left screen) to display
the MAIN menu. Press DVD Setup to access the DVD setup menu.
L
L
Press VIDEO icon to select from the following menus:
TV Shape
Press to select desired TV shape
L
Angle Mark
4:3
16:9 = DEFAULT
NORMAL - 4:3
L
WIDE - 16:9
Select On to activate angle mark
On = DEFAULT
Off
L
View Mode
Press to select desired view mode
L
41
FILL
Original
H FIT
W FIT
FIT to Screen = DEFAULT
Pan Scan
XDVD710 OPERATION
DVD Setup Menu - Rating
Rating Setup Menu
Note:
A DVD disc must be inserted
to access these functions and
features.
With the monitor open in DVD mode, press the AREA A (top left screen) to display
the MAIN menu. Press DVD Setup to access the DVD setup menu.
L
L
Press RATING icon to select from the following menus:
Enable Parental Lock Password
Press ---- to enter a password, then press Ok
Setting Parental Lock Password
Rating Setting
L
L
L
1. Enter a 4-digit code
2. Write the code down
3. Save in a safe place
When unlock symbol is displayed, press current rating then select desired rating
Parental Password Override
L
1. Kid Safe
2. G
3. PG
4. PG-13
5. PG-R
6. R
7. NC-17
8. Adult = DEFAULT
In the event you forget or loose your PARENTAL LOCK password, enter 9991.
42
XDVD710 OPERATION
CD Operation
CD User Interface
43
1)
Current MODE information, touch upper left area to return to MAIN MENU
2)
Disc title
3)
Track title
4)
Current TIME
5)
Touch to PLAY/PAUSE disc playback
6)
Touch to STOP disc playback
7)
Touch to PAGE down
8)
Touch to PAGE up
9)
Touch to FAST REVERSE current track
10)
Touch to FAST FORWARD current track
11)
Touch to SCAN CD tracks for 10 seconds each track, touch again to deactivate
12)
Touch to activate/deactivate REPEAT: Single mode
13)
Touch to activate/deactivate RANDOM mode
14)
Current track and total number of tracks on the disc
15)
Elapsed playback time
16)
Playback information
17)
Volume indicator
XDVD710 OPERATION
CD Operation
Playing CD-DA discs
After inserting a CD disc, files will play in numerical order in the directory.
L
Selecting by Keypad
Touch to display keypad. Enter desired track number and press ok.
L
Selecting by Direct Track Access
Touch desired track for DIRECT TRACK access.
L
L
Previous/Next Page
Touch to view UP/DOWN pages of available TRACKS.
44
XDVD710 OPERATION
MP3/WMA Operation
MP3/WMA User Interface
45
1)
Current MODE information, touch upper left area to return to MAIN MENU
2)
Disc title
3)
Track title
4)
Current TIME
5)
Touch to PLAY/PAUSE disc playback
6)
Touch to STOP disc playback
7)
Touch to PAGE down
8)
Touch to PAGE up
9)
Touch to PREVIOUS FOLDER
10)
Touch to NEXT FOLDER
11)
Touch to FAST FORWARD MP3 tracks, touch PLAY to deactivate
12)
Touch to activate/deactivate REPEAT: Single mode
13)
Touch to activate/deactivate RANDOM mode
14)
Touch to access the DIRECT TRACK access keypad
15)
Current track and total number of tracks on the disc
16)
Elapsed playback time
17)
Playback information
18)
Volume indicator
XDVD710 OPERATION
MP3/WMA Operation
Playing MP3/WMA files
After inserting an MP3/WMA disc, files will play in numerical order in the
directory.
L
Selecting by Single Track
Touch to display keypad. Enter desired track number and press ok.
L
Selecting by Direct Track Access
Touch desired track for DIRECT TRACK access.
L
L
Previous/Next Page
Touch to view UP/DOWN pages of available TRACKS.
46
XDVD710 OPERATION
Media Compatibility
Media Compatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW, DVD+R/RW, DVD-R/RW
• CD-DA, DVD Video
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management)
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
• WMV format
• JPG format
• DivX format
• AVI format
• MPG format
Some recordable DVDs and CDs may be incompatible with this unit,
depending on media type and recording method.
Playback Order
Compatible Recording Formats
MP3/WMA playback sequence is based on recorded order of files and begins
in the root folder of the disc. Any empty folders or folders that do not include
MP3/WMA files are skipped. This unit may not play files in the order they
were recorded in. Refer to your recording software’s user’s manual for more
information.
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum files - 1500
• Maximum folder levels - 8
• MPEG-1/2 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z (all caps), numbers
0-9, and “_” (underscore). Some characters may not be displayed correctly,
depending on the character type.
• This device can play back discs in Joliet and other standards that conform
to ISO9660. MP3/WMA written in the formats other than the above may
not play and/or their file names or folder names may not be displayed
properly.
47
XDVD710 OPERATION
Media Compatibility
Additional MP3/WMA Information
An internal buffer provides ESP (Electronic Skip Protection) to virtually
eliminate skipping.
When playing a disc recorded with regular audio files (CD-DA or .WAV) and
MP3/WMA files, the unit will play the MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA files with the
MP3/WMA extension.
Sampling Frequency Rates
MP3
32kHz ~ 48kHz
WMA
32kHz ~ 48kHz
Transfer Bit rates
MP3
WMA
40kbps ~ 320kbps constant
Variable bit rates
40kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly, depending on sampling
rates and bit rates.
Recommended Settings
For best results, use the following settings when burning an MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a WMA disc:
64kbps or higher constant bit rate
44kHz or higher sampling frequency
48
XDVD710 WARRANTY
Limited One Year Warranty
This warranty gives you specific legal rights. You may
also have other rights which vary from state to state.
Dual Electronics Corp. warrants this product to the
original purchaser to be free from defects in material
and workmanship for a period of one year from the date
of the original purchase.
Dual Electronics Corp. agrees, at our option, during
the warranty period, to repair any defect in material or
workmanship or to furnish an equal new, renewed or
comparable product (whichever is deemed necessary) in
exchange without charges, subject to verification of the
defect or malfunction and proof of the date of purchase.
Subsequent replacement products are warranted for the
balance of the original warranty period.
Who is covered? This warranty is extended to the
original retail purchaser for products purchased and
used in the U.S.A.
What is covered? This warranty covers all defects in
material and workmanship in this product. The following
are not covered: installation/removal costs, damage
resulting from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect line voltage,
unauthorized repair or failure to follow instructions
supplied with the product, or damage occurring during
return shipment of the product.
49
What to do?
1. Before you call for service, check the troubleshooting
guide in your owner’s manual. A slight adjustment of
any custom controls may save you a service call.
2. If you require service during the warranty period,
you must carefully pack the product (preferably in the
original package) and ship it by prepaid transportation
with a copy of the original receipt from the retailer to
an authorized service center.
3. Please describe your problem in writing and include
your name, a return UPS shipping address (P.O. Box
not acceptable), and a daytime phone number with
your shipment.
4. For more information and for the location of the
nearest authorized service center please contact us by
one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This warranty is
exclusive and in lieu of any and all other warranties,
expressed or implied, including without limitation
the implied warranties of merchantability and fitness
for a particular purpose and any obligation, liability,
right, claim or remedy in contract or tort, whether or
not arising from the company’s negligence, actual or
imputed. No person or representative is authorized
to assume for the company any other liability in
connection with the sale of this product. In no event
shall the company be liable for indirect, incidental or
consequential damages.
XDVD710 OPERATION
Troubleshooting
Problem
Unit will not turn on
(no power)
Cause
Action
Yellow wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC)
Red wire not connected or incorrect voltage
Black wire not connected
Check connection to ground
Fuse blown
Replace fuse
Unit has power
(but no sound)
Speaker wires not connected
Check connections at speakers
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from each other and chassis
ground
Unit blows fuse
Yellow or red wire touching chassis ground
Check for pinched wire
Speaker wires touching chassis ground
Check for pinched wire
Incorrect fuse rating
Use fuse with correct rating
Parking brake safety circuit not connected
Parking brake not applied
Check connections at parking brake
Apply parking brake
Reverse circuit not connected
Vehicle is not in reverse
Check connections at reverse lamp
Select reverse gear
Unit has audio
(but no video)
No video display
(when in reverse)
DVD does not start playback Physical defect in media
Wrong region
IR remote does not work
Excessive skipping
Bad Disc appears
on display
Incorrect Region Code
appears on display
Front panel will not
open/close
Check media for scratches
Use discs labeled "Region 1" or "All" only.
Dead battery
Replace battery
Unit is not mounted correctly
Check mounting sleeve
Physical defect in media
Check media for scratches
Focus error or disc is in upside down
Press eject or RESET
Region code error
Use only DVDs labeled “Region 1” or “All” only.
Front panel obstructed
Remove the obstacle and press OPEN again to resume the
monitor open/close sequence.
50
XDVD710 OPERATION
Specifications
DVD Player
Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 24 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
Monitor
Panel size: 7” (177.8 mm) diagonal measurement
View angle (up/down/left/right): 30/60/60/60
Resolution: 480 W x 234 H
Brightness (cd/m2): 350
Contrast ratio: 300:1
Elements: 336,960
General
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts
Line output impedance: 200 ohms
Chassis dimensions: 7" x 7" x 2"
(178 x 178 x 51 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
51
XDVD710 OPERATION
Notes
52
XDVD710 OPERATION
Notes
53
XDVD710 OPERATION
Notes
54
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©2009 Dual Electronics Corp. All rights reserved.
NSA0509-V03
Printed in China
Download PDF