Baumatic CAN75.1SS User manual

Baumatic CAN75.1SS User manual
CAN75.1SS Cooker
Hood
User Manual for your Baumatic
CAN75.1SS Cooker
Hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
1
CONTENTS
YOUR COOKER HOOD’S SPECIFICATIONS ….……………..………….3
IMPORTANT SAFETY INFORMATION……………………………….…4-5
CARING FOR THE ENVIRONMENT…………………………………………6
USING YOUR COOKER HOOD………………………………..……………..7
MAINTAINING AND CLEANING YOUR COOKER HOOD ……….8-10
INSTALLATION INSTRUCTIONS ……………………….……...….11-14
CARBON FILTER …………..11
ELECTRICAL CONNECTION……………12
INSTALLING THE COOKER HOOD……13-14
TROUBLESHOOTING ……………………………………………15
CONDITIONS OF GUARANTEE……………………………………………16
CONTACT DETAILS…………………………………………………………..17
DD 02/11/06
2
Specifications of your CAN75.1SS Cooker Hood
Congratulations on purchasing a Baumatic Cooker
Hood!
To fully enjoy using your appliance long into the future,
please firstly familiarise yourself with its specifications,
safety advice and operational instructions included in this
manual. You will also need this manual to ensure that your
Cooker Hood has been installed properly.
DIMENSIONS
Width:
Depth:
Height:
790 mm
300 mm
165 mm
Your stainless steel Cooker Hood is fitted with:
•
•
•
•
Slider control operation
3 speeds
3 metallic grease filters
2 lights
Extraction capacity – 380 m³/hr
Optional Extra:
3
2 x UCF1 Carbon filters for air
recirculation.
Important Safety Information: Please Read this before installing & using.
o
Any installation work must be
carried out by a qualified
electrician or competent person.
o
The hood must be installed in
accordance with the installation
instructions and all measurements
followed.
o
If the cooker hood is installed
for use above a gas appliance then
the provision for ventilation must
be in accordance with the Gas
Safety Codes of Practice BS.6172,
BS.5440 & BS.6891 (Natural Gas)
and BS.5482 (LP Gas) 1994, the
Gas Safety (Installation & Use)
Regulations, the Building
Regulations issued by the
Department of the Environment,
the Building Standards (Scotland)
(Consolidated) Regulations issued
by the Scottish Development
Dptmt.
o
It is dangerous to alter the
specifications or to modify this
product in any way. Do not tamper
with it or attempt to alter it in the
attempt to customise it further.
o
When installing the hood,
ensure that the following
recommended distances are being
observed between the cooker top
and the bottom of the cooker hood:
9
9
9
Electric cookers:
700 mm
Gas cookers:
700 mm
Coal/ oil cookers:
800 mm
* NOTE - DO NOT SET YOUR
COOKER HOOD LESS THAN
700mm ABOVE YOUR COOKER!
o When installed between
adjoining wall cabinets,
the cabinets must not
overhang the hob and
their undersides must be
at least 50 mm off from
the hob edges.
o The edges of the cooker
hood are sharp – be
mindful of this as you
handle your appliance,
especially during
installation and cleaning.
DO NOT CLEAN IN
BEHIND THE GREASE
FILTERS!
o If the room where the
cooker hood is to be used
contains a fuel burning
appliance such as a
central heating boiler
then its flue must be of
the sealed or balanced
flue type.
o If other types of flue or
appliances are fitted,
ensure that there is an
adequate supply of air in
the room.
o
When the hood is being
used in its extractor
function, ensure that the
ducting is fire retardant
and that there are no
bends sharper than 90
degrees as this will
reduce the efficiency of
the hood.
4
Important Safety Information: Please Read this before installing & using.
o Ensure the ducting for
the extractor function
has the same diameter as
the outlet hole all the
way through.
ventilation measures are
being observed. Note
that it removes odours
from your room, not
steam.
o Keep young children from
o Warning - Always ensure
that the cooker hood has
been disconnected from
the power supply before
carrying out any work on
the hood, including
replacing light bulbs.
using, playing with or
tampering with the
cooker hood. Older
children and infirm
persons should be
supervised if they are
using the cooker hood.
o Your cooker hood is for
domestic use only.
o Please dispose of the
packing material
carefully – children are
especially vulnerable to
it.
o Dirty oil is an even
greater fire risk.
o Always put lids on pots
and pans when cooking
on a gas cooker.
o The manufacturer
refuses to accept any
responsibility for
damages arising to the
hood or its catching on
fire from failure to
observe fire safety advice
in these instructions.
o Remember that when in
extraction mode, your
cooker hood is removing
air from your room.
Ensure that proper
5
: Do not connect the
ducting system of this
appliance to any existing
ventilation system which
is being used for any
other purpose.
: Do not install above a
cooker with a high level
grill.
: Never leave frying pans
unattended during use as
overheated fats and oils
might catch fire.
: Do not leave naked
flames under the cooker
hood.
: Do not attempt to use
the cooker hood if it is
damaged in any way.
Never attempt to use it
without the grease filters
fitted or if the filters are
excessively greasy!
: Never flambé cook under
this cooker hood.
Environmental Note
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person.
CONFORMITY TO W.E.E.E. DIRECTIVE
6
Using your Baumatic Cooker Hood:
To use your cooker hood:
1)
2)
3)
Make sure it has been properly installed.
Find the CONTROL PANEL. It is located on the hood’s front
surface near the right corner of the unit.
The CONTROL PANEL contains two rows of switches. These perform
separate functions. You will need to understand what both switches do
before you attempt to use your cooker hood.
* Note: The hood should be switched on at least as soon as you start
cooking. It is a good idea to have had it running for 5 minutes prior
to cooking and at least 15 minutes after you have finished cooking.
One row of sliding switches is for the cooker hood’s
operation
MOTOR ON /OFF switch – the ‘
’ switch (‘A’ in figure above) turns the motor
on and off and adjusts its speed. There are three speeds, pushing the switch to
the right increases the speeds. The leftmost setting is ‘OFF’.
The other is to control the light.
LIGHT ON/OFF switch - Pressing the ‘
’ switch (‘C’ in figure above) turns your
cooker hood’s light on (push left) and off (push right).
PLEASE NOTE THAT YOUR BAUMATIC COOKER HOOD CAN BE
USED EITHER IN RECIRCULATION MODE OR IN EXTRACTION
MODE. TO USE IN RE-CIRCULATION MODE, YOU WILL NEED TO
FIT THE CARBON FILTER.
7
Cleaning your Baumatic Cooker Hood:
* IMPORTANT!: Before cleaning, always ensure that you
have switched your cooker hood OFF at the omni-polar
switch, set at the wall from the cable:
Cleaning
 Clean the external parts with
mild liquid detergents on a
damp cloth.
 Never use abrasive powder,
corrosive solvents or brushes.
 Never insert pointed objects
into the motor’s protective grid.
Â
Only clean the control panel
and filter grill with a damp
cloth and delicate detergents.
 Be sure to replace the
carbon filters at the
recommended intervals.
Build up could cause a
fire hazard.
 Never take out the
grease filters and
attempt to clean the
space above where they
are set.
________________________________________________
Anti-Grease Grille
 Your cooker hood includes an anti-grease grille
which helps absorb vapour-suspended grease
particles to protect your kitchen & furniture from
greasy residues.
 The metal grille may become inflammable if it
becomes saturated with greasy residue.
9
To prevent this fire hazard, the grille should be
cleaned regularly (depending on use) every 10-15
days and at least every three months in a dishwasher
or in hot water with normal washing-up detergent.
8
Maintenance - Cleaning the Anti-grease Filters
Grease Filter
Release
First remove the anti-grease filter by pulling in the
triggers on the sides of the grille (or, for those models
with inset handholds) on the underside of the hood.
- You can now clean the anti-grease grille.
To clean the grille by hand:
9 Soak them for about one hour in hot water with a grease-loosening
detergent then rinse off thoroughly with hot water.
9 Repeat the process if needed. Refit the grease grille once it has
dried.
To clean the grilles in your
dishwasher:
9 Place the grease grilles in the
dishwasher. Select the most
powerful washing programme and
highest temperature.
9 Repeat the process, if necessary.
9 Refit the grease grille when it is dry.
Do not worry about the slight
discolouration of the grille – its
performance won’t be affected.
9
REMEMBER THAT
DISCOLOURATION OF THE
GREASE FILTER CAN TAKE
PLACE WHEN CLEANED IN
A DISHWASHER – THIS IS
NORMAL.
* NOTE - After carefully
rinsing and drying the
anti-grease grille, put it
back in place. Never put it
back in wet!
Maintenance - Changing the Light Bulb
a)
Changing the light bulb
9 Before changing the light bulb, ensure that the appliance is not
live (i.e., ensure that you have switched it off).
9 Remove the anti-grease grille to access the lamp area (see
previous page).
9
Remove the damaged light bulb.
9 Change the incandescent bulb using only olive-shaped spares with
an E14 coupling, max. 40W.
* PLEASE NOTE - Defective bulbs should be replaced
immediately.
9
Replace the metal anti-grease filter grille.
10
Installing / Changing the Carbon Filter
Your Baumatic Cooker Hood uses CARBON FILTERS to purify the air for the
air recirculation function.
You will find that one filter will attach over the front of the fan motor (please
see figure at bottom of page).
The active carbon filter must be replaced regularly, at least once every four
months, to allow normal operation.
Before starting to fit the carbon filter, turn the
omni-polar switch OFF!
Changing the Carbon Filters – Note: carbon filters cannot be cleaned!
3)
Place the new carbon
filter over the motor
bracket, making sure that
the centre button fits
exactly into the hole on the
bracket. Press lightly until
it snaps into place then
insert the centre peg.
4)
Replace the antigrease filter grille.
1) Remove the metal grease filter
grille (see page 9).
2) Take carbon filter and extract
centre peg on it about 10mm.
(If changing, remove the old
carbon filter by rotating it until
it unlatches from the sides of the
motor).
11
NOTE
If your filter is different
(i.e. is the Bayonet
Circular-insert type,
Position the filter P in
order to cover the motor
protection grille, ensuring
that the ‘X’ on the filter
lines up with the ‘Y’ on the
conveyor. Then turn
clockwise. Reverse to
dismount
INSTALLATION INSTRUCTIONS - Electrical
Before installation and usage, read all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on the identification plate (found
inside your Cooker Hood) and all the data inside the appliance are exactly the
same as the voltage and frequency in your home.
NOTE: The manufacturer declines all responsibility in the event of failure to observe all the
accident-prevention regulations in force which are necessary for normal use and regular
operation of the electric system.
______________________________________________
ELECTRICAL CONNECTION
Your cooker hood is intended for fitted and permanent installation.
o
The power cable must be
connected to the terminals
marked L (live) and N (neutral)
in the hood and fixed with a
cable clamp.
o
The cooker hood’s power cable
must be fitted upstream from the
electrical connection using an
omni-polar switch with a contact
distance of at least 3mm.
NOTE: (UK only) WARNING – THIS APPLIANCE MUST NOT BE EARTHED. It should only be
connected by a competent person using fixed wiring via a DOUBLE POLE SWITCHED FUSED
SPUR OUTLET.
We recommend that the appliance is connected by a qualified electrician who is a member
of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. The wires in
the mains lead are coloured in accordance with the following U.K. code:
Blue= Neutral, Brown = Live, Green/Yellow = Ground
If you can only find two wires in the cable (blue and brown), neither must be
connected to the Earth terminal!
•
As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals in
your spur box, please proceed as follows:
__________________________________________________________
1)
The BLUE WIRE
must be connected
to the terminal
marked ‘N’
(Neutral), or
coloured Black.
2) The BROWN
WIRE must be
connected to the
terminal marked
‘L’ (‘Live’), or
coloured RED
(Fig. 7 – at left)
12
INSTALLATION INSTRUCTIONS – installing your Cooker Hood
PLEASE NOTE THAT YOU WILL HAVE
TO DECIDE BEFORE INSTALLING YOUR
COOKER HOOD THAT YOU CAN ADAPT
IT AS AN EXTRACTION FAN.
PLEASE SEE BOXED NOTE BELOW ON
PREPARING THE CABINET.
: The cooker hood must not
be fitted above stoves with a
radiant top plate.
: We recommend that at least
two people install this hood.
ALL NEEDED SCREWS &
: Do not tile, grout or silicone
RAWLPLUGS ARE INCLUDED
this hood to the wall.
INSIDE YOUR HOOD.
1) Your Baumatic Cooker Hood should only be fitted into the underside of a
dedicated cabinet / kitchen unit. Do NOT position it any less than 700 mm
(70 cm) above the hob.
2)
Remove the metal anti-grease grille.
Preparing the cabinet Note: ‘(E)’ will appear at the beginning of an instruction
concerning how to fit the unit for the extraction function.
5) Remove the grill or the anti-grease
3) Create an opening in the bottom of filter. Remove the frame ‘C’
the cabinet to insert the cooker
provided by pressing on the two
hood and (E) drill a hole in the top
release hooks (‘D’ in picture).
of the cabinet to fit the discharge
(extraction) tube.
6) Insert the cooker hood into the
opening. Note – your cooker hood
4) (E) Connect the cooker hood to
comes with fixing screws (as
an external pipe, predispose the
shown in figures below).
electrical connection.
13
INSTALLATION INSTRUCTIONS – installing your Cooker Hood
Remember! Connect ducting for extraction
function if you intend to use your hood as
an extractor.
Ensure that you use 125mm ducting and
that an exhaust hole of about 130mm is
bored into your cabinet / kitchen unit to
accommodate it.
7) Finally, fix the cooker hood to the cabinet with the wood screws supplied
(‘G’ in figure).
8) Remount the frame (if provided) and the suction (grease filter) grille
(‘H’)
Note on Connecting spigot for ducting to your cooker hood. Your hood
must be connected to its exhaust spigot by the following method.
REMEMBER TO KEEP YOUR HOOD SECURE
WHILE YOU WORK IT INTO PLACE!
14
Troubleshooting
If something has gone wrong with your Cooker Hood, checking
against this chart might keep you from having to call for service.
Symptom
The cooker hood will not start!
The cooker hood is not working
effectively!
The cooker hood has switched off
during operation!
15
Solution
•
Check that the hood is connected
to the electricity supply.
•
Check that the fan speed control is
set properly.
•
The fan speed is not set high enough.
•
The grease filter is dirty.
•
The kitchen is not ventilated well
enough.
•
If the hood is set for recirculation,
check that the carbon filters have not
expired.
•
If the hood is set for extraction, check
that the ducting and outlets are not
blocked.
•
The safety cut-out device has been
tripped.
•
Turn off the hob and then wait for the
device to reset.
• Note that if you have installed your
cooker hood too low, this will happen.
If it happens frequently, it will be
damaged.
Baumatic Ltd. Conditions of Guarantee
Dear Customer,
Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and
labour costs resulting from defective materials or workmanship.
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12
months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period
applies to England, Scotland, Wales and Northern Ireland only.
To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase
to be covered under this guarantee. This can be done online via: www.baumatic.co.uk or through returning
the guarantee card which can be found in each new Baumatic appliance.
* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of
charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any
defect that arises due to faulty materials or workmanship within a period of 5 years from the original
purchase date.
* An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair during the
manufacturer warranty period, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
The guarantee does not cover:
- Sinks and taps
- Failure to comply with the manufacturers instructions for use.
- The replacement of cosmetic components of accessories
- Accidental damage or wilful abuse.
- Subsequent loss or damage owing to the failure of the appliance or electrical supply
- Incorrect installation
- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts
- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.
In the course of the work carried out it may be necessary to remove the appliance from it operating
position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage
sustained to any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
Contacting Baumatic Ltd
Sales
Service
Spares
TEL: 0118 933 6900
TEL: 0118 933 6911
TEL: 0118 933 6922
FAX: 0118 931 0035
FAX: 0118 986 9124
FAX: 0118 933 6942
For ROI (Republic of Ireland), please contact one of the numbers below:
TEL: 01 – 6266798
FAX: 01 - 6266634
Technical/Advice
0118 933 6933
0118 933 6942
Thanks you for buying Baumatic.
* Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)
Baumatic Ltd
Make-up for your kitchen
Headquarters
Baumatic Ltd.
Baumatic Buildings,
6 Bennet Road,
Reading,
Berkshire
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
Sales Fax
+44 118 931 0035
Service Telephone
+44 118 933 6911
Service Fax
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
E-mail:
[email protected]
[email protected]
Http (Internet site):
www.baumatic.com
Baumatic UK/cod. 1230000666
17
18
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement