Altherma | ERLQ016CAW1 | Technical data | Altherma ERLQ016CAW1 Technical data

DACA-EEDEN09-720
technical
data
Engineering Data
DaikinAltherma
DACA-EEDEN09-720
Daikin Altherma Engineering Data
Part 1: Overview
1. Daikin Altherma Overview .......................................................................... 1
1.1 Daikin Altherma Split System ..........................................................................1
1.2 Daikin Altherma Monobloc System .................................................................2
1.3 System Configurations ...................................................................................3
2. The Basics of Daikin Altherma ................................................................... 4
2.1 Air-to-Water Heat Pump ..................................................................................4
2.2 Split Type ........................................................................................................6
2.3 Monobloc .........................................................................................................7
3. Model Indentification................................................................................... 8
3.1 Outdoor Units ..................................................................................................8
3.2 Indoor Units .....................................................................................................8
3.3 Options ............................................................................................................9
4.
5.
6.
7.
System and Design Recommendations ..................................................
Combination Overview ............................................................................
Split System Component Selection .........................................................
Monobloc Component Selection..............................................................
10
13
14
15
Part 2: ERLQ036_048_054BAVJU Split Type
1. ERLQ - Split System Outdoor Unit ........................................................... 16
1.1 Feature ..........................................................................................................16
2. Specifications - Split System .................................................................... 17
3. Capacity Tables - Split System................................................................. 20
3.1 Heating ..........................................................................................................20
3.2 Cooling .........................................................................................................21
4. Dimensional Drawing - Split System ........................................................
5. Center of Gravity - Split System ...............................................................
6. Piping Diagram - Split System..................................................................
7. Wiring Diagram - Split Sytem ...................................................................
8. Sound Data - Split System .......................................................................
9. Installation - Split System .........................................................................
22
23
24
25
26
27
9.1 Installation Location ......................................................................................27
9.2 Installation Space .......................................................................................28
10. Operation Range - Split System ............................................................. 29
I
DACA-EEDEN09-720
Part 3: EKHBH054BA Hydrobox
1. EKHBH054BA - Hydrobox........................................................................ 30
1.1 Features ........................................................................................................30
2. Specifications - Hydrobox.........................................................................
3. Dimensional Dwg. & Center of Gravity- Hydrobox ...................................
4. Piping Diagram - Hydrobox ......................................................................
5. Wiring Diagram - Hydrobox ......................................................................
31
33
34
35
5.1 EKHB(H/X)054BA3VJU ................................................................................35
5.2 EKHB(H/X)054BA6VJU ................................................................................36
6. External Connection Diagram - Hydrobox ................................................
7. Condensate Instructions - Hydrobox ........................................................
8. Application Examples - Hydrobox............................................................
9. Hydronic Performance - Hydrobox ..........................................................
10. Operation Range - Hydrobox .................................................................
37
38
39
43
44
Part 4: EDLQ / EBLQ_036_048_054 Monobloc
1. Monobloc - EDLQ / EBLQ ........................................................................ 45
1.1 Features ........................................................................................................45
2. Specifications  EDLQ  Heat Only .........................................................
3. Capacity Tables  EDLQ  Heat Only ......................................................
4. Specifications  EBLQ Heat Pump...........................................................
5. Capacity Tables  EBLQ  Heating..........................................................
6. Capacity Tables  EBLQ Cooling ..........................................................
7. Dimensional Drwg. & Center of Gravity - Monobloc .................................
8. Piping Diagram - Monobloc .....................................................................
9. Wiring Diagram - Monobloc ......................................................................
46
50
51
55
56
57
58
59
9.1 Wiring Diagram - Monobloc ...........................................................................60
9.2 External Connection Diagram - Monobloc ....................................................61
10. Sound Data - Monobloc.......................................................................... 62
10.1 Sound Pressure Spectrum - Normal Operation ..........................................62
10.2 Sound Pressure Night Quiet Mode .............................................................62
11. Application Examples - Monobloc .......................................................... 63
12. Installation - Monobloc............................................................................ 68
12.1 Installation Location ....................................................................................68
12.2 Installation Space .......................................................................................69
13. Hydronic Performance - Monobloc ......................................................... 70
14. Operation Range - Monobloc ................................................................. 71
II
DACA-EEDEN09-720
Part 5: EKHWS050_080BA3VJU Domestic Hot Water
1. Domestic Hot Water Tank ........................................................................ 72
1.1 Features ........................................................................................................72
2. Specifications - DHW................................................................................ 73
3. Domestic Hot Water Basic Performance Overview .................................. 74
4. Dimensional Drawing & Center of Gravity - DHW ................................... 75
4.1 Domestic Hot Water Tank Summary .............................................................76
5. Three-Way Valve Summary .................................................................... 77
Part 6: Options
1. Solar Kit (EKSOLHWBAVJU) ................................................................... 79
1.1 Features ........................................................................................................79
2. Specifications  Solar Kit.......................................................................... 80
3. Dimensional Drwg. & Center of Gravity - Solar Kit ................................... 81
3.1 Piping Diagram - Solar Kit .............................................................................82
3.2 Wiring Diagram - Solar Kit .............................................................................83
4. Room Thermostat  EKRTWA ................................................................ 84
4.1 Specifications - Room Thermostat ..............................................................85
4.2 Dimensions - Room Thermostat ..................................................................86
4.3 Application Example - Room Thermostat ......................................................87
4.4 Wiring Connection - Room Thermostat .........................................................88
4.5 User Display - Room Thermostat ..................................................................89
4.6 Functional Summary - Room Thermostat .....................................................90
5. Condensate Kit  EKHBDP ...................................................................... 91
6. Digital I/O PCB Kit  EKRP1HBAAU ........................................................ 92
Part 7: Appendix - Field Settings Overview
1. Field Settings Overview............................................................................ 93
III
DACA-EEDEN09-720
Daikin Altherma Overview
1. Daikin Altherma Overview
1.1
Daikin Altherma Split System
Daikin Altherma is a Total Comfort air-to-water heat pump system that utilizes an outdoor R-410A heat
pump system, with Inverter controlled compressor, to extract heat from the outdoor air and transfers this
heat through refrigerant piping to a refrigerant-to-water cupro-nickel brazed plate heat exchanger in the
hydrobox (indoor unit on split system and incorporated in the outdoor unit on the monobloc). The hydrobox
circulates the heated water through low temperature heat emitters (low temperature radiators, floor heating systems and fan coil units) and also provides domestic hot water (DHW) with the optional DHW tank
(316L stainless steel heat exchanger and tank). The heat pump version of the hydrobox can reverse the
cycle and provide chilled water for cooling through fan coil units (fan coil units for cooling are field supplied
and must have a condensate drain pan). Daikin Altherma can heat spaces, produces domestic hot water
and with the heat pump version hydrobox or monobloc can cool spaces.
The high coefficient of performance (COP) of the Daikin Altherma heat pump is largely attributed to the
Daikin inverter principle. An integrated frequency converter adjusts the rotational speed of the compressor
to suit the heating (cooling) demand. The system seldom operates at full capacity and maximizes
efficiency by controlling the compressor rpm.
1
Daikin Altherma Overview
DACA-EEDEN09-720
1.2
2
Daikin Altherma Overview
Daikin Altherma Monobloc System
Daikin Altherma Overview
DACA-EEDEN09-720
1.3
Daikin Altherma Overview
System Configurations
Selection Conditions
Typical conditions for the heating LWT are:
86 to 95° F (at design conditions) for floor heating
86 to 113° F (at design conditions) for fan coil units
104 to 122° F (at design conditions) for low temperature radiators
3
Daikin Altherma Overview
DACA-EEDEN09-720
The Basics of Daikin Altherma
2. The Basics of Daikin Altherma
2.1
4
Air-to-Water Heat Pump
The Basics of Daikin Altherma
DACA-EEDEN09-720
The Basics of Daikin Altherma
5
The Basics of Daikin Altherma
DACA-EEDEN09-720
2.2
The Basics of Daikin Altherma
Split Type
6
The Basics of Daikin Altherma
DACA-EEDEN09-720
2.3
7
The Basics of Daikin Altherma
Monobloc
The Basics of Daikin Altherma
DACA-EEDEN09-720
Model Indentification
3. Model Indentification
3.1
Outdoor Units
3.2
Indoor Units
8
Model Indentification
DACA-EEDEN09-720
3.3
9
Model Indentification
Options
Model Indentification
DACA-EEDEN09-720
System and Design Recommendations
4. System and Design Recommendations
10
System and Design Recommendations
DACA-EEDEN09-720
System and Design Recommendations
11
System and Design Recommendations
DACA-EEDEN09-720
System and Design Recommendations
Daikin Altherma Checklist
Quote #:
Low Temperature Mode
Job Name:
Date:
Customer:
Required by:
Contact:
PO:
A) Sizing Information:
Outdoor Temperature Where Heat Loss = Zero: __________Night Setback Temperature: _________
Heat Loss:
Heat Gain (if cooling):
Btu/h
Btu/h
Heating Months:
Total Area
Energy Cost: Electricity____kW; Gas____Therm; Oil____gal
Square Feet
Peak / Standard Demand Charge Period______________
Details:
B) System Selection:
System Layout:
Split System
Monobloc (packaged unit)
(R410A piping to indoor hydrobox)
(H2O piping to inside) (Includes 6 kW 2-stage backup heater)
System Type:
Backup heater selection is not applicable to Monobloc
Heating Only
Heat Pump (Heating & Cooling)
EKHBH-Split System / EDLQ-Monobloc
System Criteria:
Heating (LWT _______°F/°C)
(Maximum temperature 131°F / 55°C)
System Source:
100% Heat Pump
Cooling (LWT _______°F/°C)
3 kW
Backup heat capacity
6kW
Backup heat capacity 2-stage
DHW (Water Temp _______°F/°C)
(EKBDHP Condensate Kit Required)
Heat Pump w/Electric Heater
(Mono-Valent)
Heat Emitters:
EKHBX-Split System / EBLQ-Monobloc
(Mono-Energetic)
Heat Pump with Auxiliary Boiler
(Bi-Valent)
Dual Setpoint Temperature:______high______low
Type
Heat or Cool
Capacity Btu/h
CFM-Fan Coil
Additional Heat EmitterSpecifications
Radiant Floor
86 to 95°F / 30 to 35°C
Fan Coil
86 to 113°F / 30 to 45°C
Low Temp Radiators
104 to 122°F / 40 to 50°C
Domestic Hot Water:
50 Gallon
(Integrated 3kW booster heater)
80 Gallon
(Integrated 3kW booster heater)
Optional Solar Kit
(connection kit to storage tank only)
Solar Option:
Storage Tank Connection Kit
Control Board Interface (PCB)
(connection kit to storage tank only)
Thermostats:
Daikin Thermostat (EKRTWA)
Zone Thermostats (by others)
(Wired to hydro box)
Room Thermostat (by others)
(Wired to hydro box) Must have 6 min. run time
Notes:
Order # _____________________
Date____________________
Person____________________
Version 3 (2009)
12
System and Design Recommendations
13
2
X
EKRP1HBAAU
EKSOLHWBAVJU
EKRTWA
EKHBDP
Solar Pump Kit
Wired
Thermostat
Condensate Kit
X
1
2
X
EKHWS080BA3VJU
EKRP1HBAAU
EKSOLHWBAVJU
EKRTWA
EKHBDP
Digital I/O PCB
Solar Pump Kit
Wired
Thermostat
Condensate Kit
3
X
2
1
X
X
X
X
X
N/A
X
2
1
X
X
N/A
X
2
1
X
X
Monobloc Heating Only
EDLQ048BA6VJU
EDLQ054BA6VJU
N/A
X
2
1
X
X
X
X
X
Notes:
X - Can be applied
1 - Applied with Solar Pump Kit (DHW solar priority); alarm output; Bi-Valent operation (auxiliary boiler)
2 - Can be applied with DHW Tank (thermal solar panels and pump station to be field supplied)
3 - Must be applied with Heat Pump Hydrobox
N/A
X
EDLQ036BA6VJU
N/A
EKHWS050BA3VJU
DHW Tank (50
gal)
DHW Tank (80
gal)
Combination Overview
Daikin Altherma Monobloc
X
EKHWS080BA3VJU
Digital I/O PCB
1
X
X
ERLQ054BAVJU
EKHWS050BA3VJU
X
X
ERLQ048BAVJU
ERLQ036BAVJU
N/A
X
2
1
X
X
N/A
X
2
1
X
X
EBLQ048BA6VJU
N/A
X
2
1
X
X
EBLQ054BA6VJU
Monobloc Heat Pump (Reversible)
EBLQ036BA6VJU
3
X
2
1
X
X
X
X
X
Hydrobox Heating Only
Hydrobox Heat Pump (Reversible)
EKHBH054BA3VJU EKHBH054BA6VJU EKHBX054BA3VJU EKHBX054BA6VJU
DHW Tank (50
gal)
DHW Tank (80
gal)
Outdoor Unit
Combination Overview
Daikin Altherma Split System
DACA-EEDEN09-720
Combination Overview
5. Combination Overview
Combination Overview
14
Heating,
Cooling
and/or
DHW
No
Heating
Only
and/or
DHW
Daikin Altherma
System Selection
from Checklist
Indoor Unit
Outdoor
Unit
Yes
Indoor Unit
Outdoor
Unit
EKHBDP Condensate Kit
(Must be applied to
heating/cooling hydro box)
EKHBX054BA3
EKHBX054BA6
(3=3 kW; 6=6 kW Backup
Heater)
ERLQ036
ERLQ048
ERLQ054
Daikin Altherma
Options from
Checklist
EKHBH054BA3
EKHBH054BA6
(3=3 kW; 6=6 kW Backup
Heater)
Daikin Altherma
Options from
Checklist
ERLQ036
ERLQ048
ERLQ054
Size Selection of
Daikin Altherma
Based on Heat Loss
Yes
Size Selection of
Daikin Altherma
Based on Heat Loss
Daikin Altherma Split System Component Selection (All Outdoor units have base pan heater)
EKRP1HBAAU
Digital I/O PCB
EKRTWA
Wired Room
Thermostat
DHW Solar Option
EKSOLHWBA
EKHWS050BA3 (50 gal)
EKHWS080BA3 (80 gal)
Both DHW Tanks Have
3 kW Booster Heater
EKRP1HBAAU
Digital I/O PCB
EKRTWA
Wired Room
Thermostat
DHW Solar Option
EKSOLHWBA
EKHWS050BA3 (50 gal)
EKHWS080BA3 (80 gal)
Both DHW Tanks Have
3 kW Booster Heater
DACA-EEDEN09-720
Split System Component Selection
6. Split System Component Selection
Split System Component Selection
15
Heating,
Cooling
and/or
DHW
No
Heating
Only
and/or
DHW
Daikin Altherma
System Selection
from Checklist
Monobloc Units
EDLQ036BA6VJU
EDLQ048BA6VJU
EDLQ054BA6VJU
Yes
Monobloc Units
EBLQ036BA6VJU
EBLQ048BA6VJU
EBLQ054BA6VJU
Size Selection of
Daikin Altherma
Based on Heat Loss
Yes
Size Selection of
Daikin Altherma
Based on Heat Loss
(all monobloc units have
6 kW backup heater)
Daikin Altherma
Options from
Checklist
(all monobloc units have
6 kW backup heater)
Daikin Altherma
Options from
Checklist
EKRP1HBAAU
Digital I/O PCB
EKRTWA
Wired Room
Thermostat
DHW Solar Option
EKSOLHWBA
EKHWS050BA3 (50 gal)
EKHWS080BA3 (80 gal)
Both DHW Tanks Have
3 kW Booster Heater
EKRP1HBAAU
Digital I/O PCB
EKRTWA
Wired Room
Thermostat
DHW Solar Option
EKSOLHWBA
EKHWS050BA3 (50 gal)
EKHWS080BA3 (80 gal)
Both DHW Tanks Have
3 kW Booster Heater
Daikin Altherma Monobloc System Component Selection (All monobloc units have base pan heater)
DACA-EEDEN09-720
Monobloc Component Selection
7. Monobloc Component Selection
Monobloc Component Selection
DACA-EEDEN09-720
ERLQ - Split System Outdoor Unit
1. ERLQ - Split System Outdoor Unit
1.1
Features
•
Inverter operated compressor
•
Single phase large capacity outdoor unit (036, 048, 054)
•
Cost effective alternative to a fossil fuel boiler
•
Low energy bills and low CO2 emissions
•
Easy to install
•
Total solution for year round comfort
•
Anti-corrosion treatment on outdoor coil
•
Bottom base pan heater to improve water drainage during defrost
ERLQ outdoor units are combined with an indoor hydrobox; a heating-only hydrobox version (EKHBH), and a heat
pump (heating & cooling) hydrobox version (EKHBX). Both hydrobox versions can be applied with an optional
domestic hot water tank (EKHWS) and optional solar pump kit (EKSOLHW)
16
ERLQ - Split System Outdoor Unit
DACA-EEDEN09-720
Specifications - Split System
2. Specifications - Split System
2-1 NOMINAL CAPACITY AND NOMINAL
INPUT
For
combination
indoor units +
outdoor units
For
combination
indoor units +
outdoor units
ERLQ048BAVJU
ERLQ054BAVJU
EKHBH054BA
(Heating Only)
Condition
Heating
(Floor Heating) capacity
Condition 2
(Fan Coil)
ERLQ036BAVJU
Indoor Units
Nominal
kBTU/hr (kW)
Heating PI
Nominal
kW
COP
Nominal
Heating
capacity
Nominal
kBTU/hr (kW)
Heating PI
Nominal
kW
COP
Nominal
38.2 (11.2)
47.8 (14.0)
54.6 (16.0)
2.58
3.30
3.97
4.34
4.24
4.03
35.3 (10.3)
44.8 (13.1)
51.8 (15.2)
3.18
4.00
4.79
3.24
3.28
3.17
Indoor Units
EKHBX054BA
(Reversible)
Condition 1
Heating
(Floor Heating) capacity
Nominal
kBTU/hr (kW)
38.2 (11.2)
47.8 (14.0)
54.6 (16.0)
Cooling
capacity
Nominal
kBTU/hr (kW)
47.6 (13.9)
59.1 (17.3)
60.6 (17.8)
Heating PI
Nominal
kW
2.58
3.30
3.97
Cooling PI
Nominal
kW
3.91
5.94
6.94
COP
Nominal
4.34
4.24
4.03
EER
Nominal
12.17
9.95
8.73
Heating
capacity
Nominal
kBTU/hr (kW)
35.3 (10.3)
44.8 (13.1)
51.8 (15.2)
Cooling
capacity
Nominal
kBTU/hr (kW)
34.1 (10.0)
42.7 (12.5)
44.7 (13.1)
Heating PI
Nominal
kW
3.18
4.00
4.79
Cooling PI
Nominal
kW
3.72
5.41
6.08
COP
Nominal
3.24
3.28
3.17
EER
Nominal
9.17
7.89
7.35
Condition 2
(Fan Coil)
Notes
Condition 1: cooling Ta 95°F (35°C) - LWE 64.4°F (18°C) - heating Ta DB/WB 44.6/42.8°F (7/6°C - LWC 95°F
(35°C) ( T = 9°F (5°C )
Condition 2: cooling Ta 95°F (35°C) - LWE 45°F (7°C) (T = 9°F (5°C ) - heating Ta DB/WB 44.6/42.8°F (7/6°C)
- LWC 113°F (45°C) ( T = 9°F (5°C )
2-2
TECHNICAL SPECIFICATIONS
Casing
ERLQ036BAVJU
Colour
Unit
Packing
Weight
Packing
ERLQ054BAVJU
Ivory white
Material
Dimensions
ERLQ048BAVJU
Painted galvanised steel plate
Height
in (mm)
Width
in (mm)
35.4” (900 mm)
46” (1,170 mm)
35.4” (900 mm)
35.4” (900 mm)
Depth
in (mm)
12-1/2” (320 mm)
12-1/2” (320 mm)
12-1/2” (320 mm)
Height
in (mm)
Width
in (mm)
38-1/2” (980 mm)
53” (1,349 mm)
38-1/2” (980 mm)
38-1/2” (980 mm)
Depth
in (mm)
16-1/2” (420 mm)
16-1/2” (420 mm)
16-1/2” (420 mm)
Unit
lb (kg)
227 lb (103 kg)
227 lb (103 kg)
227 lb (103 kg)
Packed Unit
lb (kg)
251.3 lb (114 kg)
251.3 lb (114 kg)
251.3 lb (114 kg)
Material
EPS
Carton
Wood
PP (Straps)
Weight
17
lb (kg)
24.3 lb (11 kg)
24.3 lb (11 kg)
24.3 lb (11 kg)
Specifications - Split System
DACA-EEDEN09-720
2-2
Specifications - Split System
TECHNICAL SPECIFICATIONS
Heat
Exchanger
Dimensions
Length
ERLQ036BAVJU
ERLQ048BAVJU
ERLQ054BAVJU
in (mm)
33-3/4” (857 mm)
33-3/4” (857 mm)
33-3/4” (857 mm)
2
2
2
in (mm)
1/16” (1.4 mm)
1/16” (1.4 mm)
1/16” (1.4 mm)
Nr of Rows
Fin Pitch
Nr of Passes
Face
Area
ft² (m²)
# of Stages
6
6
6
3.22 ft² (0.98 m²)
3.22 ft² (0.98 m²)
3.22 ft² (0.98 m²)
52
52
52
Tube type
Fin
Hi-XSS(8)
Type
WF fin
Treatment
Fan
Anti-corrosion treatment (PE)
Type
Propeller
Quantity
Air Flow Rate
(nominal at
230V)
Fan
2
2
2
Heating
High
cfm (m³/min)
3178 cfm (90 m³/min)
3178 cfm (90 m³/min)
3178 cfm (90 m³/min)
Cooling
High
cfm (m³/min)
3355 cfm (96 m³/min)
3531 cfm (100 m³/min)
3426 cfm (97 m³/min)
Discharge direction
Motor
Horizontal
Quantity
2
Model
Motor
Speed
(nominal)
Steps
Cooling
rpm
Fan
Motor
Output
W
Compressor
Quantity
Heating
rpm
8
8
8
760
760
800
850
830
70 each
70 each
70 each
Direct drive
1
Model
2,200
Starting Method
Crankcase
Heater
Output
W
Ambient
Operation
Range
Heating
Min
Max
Sanitary water
Sound Level
(nominal) *1
Refrigerant
Inverter driven
33
33
33
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
°F (°C)
95 (35)
95 (35)
95 (35)
Min
°F (°C)
50 (10)
50 (10)
50 (10)
Max
°F (°C)
114.8 (46)
114.8 (46)
114.8 (46)
Min
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
Max
°F (°C)
109.4 (43)
109.4 (43)
109.4 (43)
Sound
Power
dBA
95 (35) HP / 109.4 (43) BH
64
95 (35) HP / 109.4 (43) BH)
64
95 (35) HP / 109.4 (43) BH
66
Sound
Pressure
dBA
49
51
53
Sound
Power
dBA
64
66
69
Sound
Pressure
dBA
50
52
54
Heating
Sound
Pressure
dBA
42
42
43
Cooling
Sound
Pressure
dBA
45
45
46
8.2 lb (3.7 kg)
8.2 lb (3.7 kg)
Heating
Cooling
Sound Level
(Night quiet)
Type
Charge
R-410A
oz (kg)
Control
18
1
Type
Charged Volume
8.2 lb (3.7 kg)
Expansion valve(electronic type)
Nr of Circuits
Refrigerant Oil
1
Hermetically sealed scroll compressor
W
Motor
Cooling
1
JT100G-VD
Type
Motor
Output
2
760
Drive
Motor
2
Brushless DC motor
1
1
Daphne FVC68D
g (l)
1.06 g (1.0 l)
1.06 g (1.0 l)
1.06 g (1.0 l)
Specifications - Split System
DACA-EEDEN09-720
2-2
Specifications - Split System
TECHNICAL SPECIFICATIONS
Piping
connections
Liquid (OD)
Quantity
ERLQ036BAVJU
ERLQ048BAVJU
ERLQ054BAVJU
1
1
1
Type
Diameter
(OD)
Gas
Flare connection
in (mm)
3/8” (9.52 mm)
Quantity
1
1
Type
Diameter
(OD)
Drain
in (mm)
5/8” (15.9 mm)
Quantity
3
3
Type
Piping Length
3
Hole
Diameter
(OD)
in (mm)
Minimum
ft (m)*2
1-1/32” (26 mm)
Maximum ft (m)
1-1/32” (26 mm)
1-1/32” (26 mm)
16.4 ft (5 m)
16.4 ft (5 m)
16.4 ft (5 m)
246 ft (75 m)
246 ft (75 m)
246 ft (75 m)
Equivalent ft (m)
312 ft (95 m)
312 ft (95 m)
312 ft (95 m)
Chargeless ft (m)
98.4 ft (30 m)
98.4 ft (30 m)
98.4 ft (30 m)
Additional Refrigerant
Charge
Installation
height
difference
1
Flare connection
kg
See installation manual outdoor unit
Maximum ft (m)
98.4 ft (30 m)
98.4 ft (30 m)
Heat Insulation
98.4 ft (30 m)
Both liquid and gas pipes
Defrost Method
Pressure equalizing
Defrost Control
Sensor for outdoor heat exchanger temperature
Capacity Control Method
Inverter controlled
Safety Devices
Fan motor thermal protector
Fuse
High pressure switch
Standard
Accessories
Item
Tie-wraps
Quantity
2
2
Item
Quantity
1
1
1
(*1) The sound pressure level is measured via a microphone at a certain distance from the unit. It is a relative value
depending on the distance and acoustic environment. Refer to sound spectrum drawing for more information.
Notes
2-3
(*2) Down to 10 ft. (3 m) with recharging of the outdoor unit. Refer to the installation manual of the outdoor unit.
ELECTRICAL SPECIFICATIONS
Power Supply
ERLQ036BAVJU
ERLQ048BAVJU
ERLQ054BAVJU
Name
VJU
VJU
VJU
Phase
1~
1~
1~
Frequency
Hz
60
60
60
Voltage
V
208-230
208-230
208-230
Voltage range
Compressor
Current
Total
Minimum
V
-10%
-10%
-10%
Maximum
V
+10%
+10%
+10%
Rated Load Amps (RLA)
A
23.4
23.4
23.4
Full Load Amps (FLA)
A
26.5
26.5
26.5
Minimum Current Protection
(MCA)
A
26.5
26.5
26.5
A
30
30
30
Maximum Current Protection
(MOP)
Wiring
Connections
19
2
Installation manual
For Power
Supply
Remark
See installation manual outdoor unit
For Connection
with Indoor
Remark
See installation manual outdoor unit
Power Supply Intake
Outdoor Unit Only
Notes
Standard for Safety Heating and Cooling Equipment; UL1995/CSA (U&C) C22.2 #236.
Specifications - Split System
DACA-EEDEN09-720
Capacity Tables - Split System
3. Capacity Tables - Split System
3.1
Heating
Peak value does not include capacity drop during frosting and defrosting periods.
Integrated value takes into consideration the capacity drop during frosting and defrosting periods.
20
Capacity Tables - Split System
DACA-EEDEN09-720
3.2
Capacity Tables - Split System
Cooling
Symbols:
CC
HC
PI
LWE
LWC
Tamb
Cooling Capacity @ maximum operating frequency, BTU/h
Heating Capacity @ maximum operating frequency, BTU/h
Cooling Power Input (kW), Heating Power Input (kBTU/h measured according to Eurovent 6/C003-2006 (kW)/EN14511
Leaving Water evaporator temperature (Cooling)
Leaving Water condenser temperature (Heating)
Outdoor Ambient temperature, RH = 85%
Conditions:
Cooling Capacity BTU/h and valid for chilled water range T = 5-150F (3-80C)
Heating Capacity is according to Eurovent 6/C/003-2006 (kW) and valid for heating water range T = 5-150F (3-80C)
Power Input is total of indoor and outdoor unit, except the circulation pump; (90W per EN14511)
21
Capacity Tables - Split System
DACA-EEDEN09-720
Dimensional Drawing - Split System
4. Dimensional Drawing - Split System
22
Dimensional Drawing - Split System
DACA-EEDEN09-720
Center of Gravity - Split System
5. Center of Gravity - Split System
23
Center of Gravity - Split System
DACA-EEDEN09-720
Piping Diagram - Split System
24
5/8”
3/8”
6. Piping Diagram - Split System
Piping Diagram - Split System
DACA-EEDEN09-720
Wiring Diagram - Split Sytem
7. Wiring Diagram - Split Sytem
25
Wiring Diagram - Split Sytem
DACA-EEDEN09-720
Sound Data - Split System
8. Sound Data - Split System
Normal Operation:
Night Quiet Operation:
26
Sound Data - Split System
DACA-EEDEN09-720
Installation - Split System
9. Installation - Split System
9.1
•
•
•
•
•
•
•
•
•
•
•
Installation Location
The equipment is not is not intended for use in a potentially explosive atmosphere.
Choose a place solid enough to bear the weight and vibration of the unit, where operation
sounds will not be amplified.
Locate the unit so that operation sounds and discharged hot/cold air will not bother neighbors.
Avoid places such as bedrooms so that operation sounds are not a problem.
Allow sufficient space for carrying the unit into and out of the site.
Ensure there is sufficient space for air passage and a lack of obstructions around the air inlet
and the air outlet.
The site must be free from the possibility of flammable gas leakage in any nearby area.
Install units, power cable, and inter-unit cables at least 10 feet (3 m) away from televisions
and radios to prevent interference.
Depending on radio wave conditions, electromagnetic interference may still occur even if
installed more than 10 ft. (3 m) away.
In coastal areas or other places with salty atmosphere of sulfate gas, corrosion my shorten the
life of the outdoor unit.
Since condensate flows out of the outdoor unit, do not place anything under the unit that must
be kept from moisture.
IN COLD CLIMATES:
•
•
•
•
•
27
To prevent exposure to wind, install the outdoor unit with its suction side facing the wall.
Never install the outdoor unit at a site where the suction side may be exposed directly to wind.
To prevent exposure to wind, install a baffle plate on the air discharge side of the outdoor unit.
Unit should be installed with a minimum of 4” (10 cm) free space below the unit’s bottom plate
at all condition, e.g., heavy snowfall (construct a pedestal if necessary).
In heavy snowfall areas, it is very important to select an installation site where the snow will
not affect the unit. If lateral snowfall is possible, make sure the heat exchanger coil is not
affected by the snow (construct a lateral canopy if necessary). See Figure 1:
Installation - Split System
DACA-EEDEN09-720
9.2
28
Installation - Split System
Installation Space
Installation - Split System
DACA-EEDEN09-720
Operation Range - Split System
10. Operation Range - Split System
29
Operation Range - Split System
DACA-EEDEN09-720
EKHBH054BA - Hydrobox
1. EKHBH054BA - Hydrobox
1.1
Features 
•
Heating only - EKHBH054BA
•
Heat Pump (heating & cooling) - EKHBX054BA
•
Large capacity indoor unit
•
Cost effective alternative to a fossil fuel boiler
•
Low energy bills and low CO2 emissions
•
Interface control with field selectable options that include dual set point (heating & cooling), Quiet Mode, DHW
priority settings, schedule timer.
•
Easy to install
•
Total solution for year round comfort
•
Apply with split system outdoor unit (ERLQ)
•
Select from 2 sizes of integrated backup heat 3kW (single stage) or 6 kW (2-stage)
The hydrobox is the indoor part of the air-to-water ERLQ outdoor heat pump. These units are designed for
wall-mounted indoor installation. The units can be combined with fan coil units, floor heating applications,
low temperature radiators, optional Daikin Domestic Hot Water Tanks, and optional Daikin Solar Kits for
domestic hot water applications.
The unit range consists of two main versions: a heating/cooling version (EKHBX) and a heating-only
version (EKHBH). Both versions are delivered with an integrated backup heater for additional heating
during cold outdoor temperatures. The backup heater also serves as a backup if malfunctioning of the
outdoor unit should occur. The backup heater models are available for a heating capacity of 3kW and
6kW.
30
EKHBH054BA - Hydrobox
DACA-EEDEN09-720
Specifications - Hydrobox
2. Specifications - Hydrobox
2-1
TECHNICAL SPECIFICATIONS
Outdoor units
EKHBH*
EKHBX*
EKHBH054BA*
EKHBX054BA*
ERLQ036BAVJU ERLQ048BAVJU ERLQ054BAVJU
ERLQ036BAVJU ERLQ048BAVJU ERLQ054BAVJU
Nominal input (Indoor only without electric
heater)
Casing
208-230V / 1 ph / 60Hz
Color
Neutral White RAL9010
Material
Dimensions
Packing
Unit
Weight of unit
Weight of
packing
materials
Epoxy polyester painted galvanized steel
Height
in (mm)
Width
in (mm)
49.23 (1225)
25.98 (660)
Depth
in (mm)
24.02 (610)
36.30 (922)
Height
in (mm)
Width
in (mm)
19.76 (502)
Depth
in (mm)
14.21 (361)
Machine net weight
lbs (kg)
123 (55)
Packed machine weight
lbs (kg)
152 (69)
Material
EPS, Wood, Carton, PP (straps)
lbs (kg)
Weight
29 (14 )
Type
water cooled
3
no. of speeds
Pump
Nominal
ESP unit
Cooling
Heating
Power Input
psi
(kPa)
psi
(kPa)



8.04 (55.4)
6.53 (45.0)
6.13 (42.3)
7.34 (50.7)
5.48 (37.8)
3.92 (27.1)
7.34 (50.7)
5.48 (37.8)
3.92 (27.1)
W
210
Type
Brazed Plate
Quantity
Main
Components
Water Side
Heat
Exchanger
1
Water volume
gal/m (l/
min)
0.27 (1.01)
Water flow
rate Min.
gal/m
(l/min)
4.23 (16)
Water flow
rate Nom.
Water flow
rate Max.
Cooling
(2)
gal/m
(l/min)



7.58 (28.7)
9.45 (35.8)
9.90 (37.5)
Heating
(3)
gal/m
(l/min)
8.47 (32.1)
10.59 (40.1)
12.12 (45.9)
8.47 (32.1)
10.59 (40.1)
12.12 (45.9)
Cooling
gal/min
(l/min)
15.3 (58)
Heating
gal/min
(l/min)
15.3 (58)
Insulation
material
Expansion
vessel
Volume
gal/min
(l/min
Max. water
pressure
psi (bar
Pre pressure
Water Filter Diameter
perforations
Material
31
Polyurethane foam
2.64 (10)
43.5 (3)
psi (bar)
14.3 (1)
inch
(mm)
0.039 (1)
brass
Specifications - Hydrobox
DACA-EEDEN09-720
2-1
Specifications - Hydrobox
TECHNICAL SPECIFICATIONS
Piping Connections
Water Circuit
G 1-1/4 (MALE) BSP
Piping
in (mm)
1-1/4 (31.8) BSP
Safety valve
psi (bar)
43.5 (3)
Manometer
Yes
Drain valve / Fill valve
Yes
Shut-off valve
Yes
Air Purge valve
Total water volume (6)
Refrig. Circuit
Sound Level
Operation
range
Yes
gal (l)
1.45 (5.5)
Gas side
in (mm)
5/8 (15.9)
Liquid side
in (mm)
3/8 (9.52)
Sound PresHeating
sure (4)
dBA
28
Sound
power
dBA

Ambient
Waterside
Cooling
°F (°C)

50 ~ 114.8 (10 ~ 46)
Heating
°F (°C)
-4 ~ 95 (-20 ~ 35)
-4 ~ 95 (-20 ~ 35)
Heating
°F (°C)

41 ~ 76.6 (5 ~22)
Heating (5)
°F (°C)
59 ~ 131 (15 ~ 55)
59 ~ 131 (15 ~ 55)
* (1) With option kit EKHBDP installed: Height = 36.85” (936 mm)
* (2) Tamb 95°F (35°C) LWE 44.6°F (7 C) (DT = 9°F (5°C)
* (3) DB/WB 44.6°F/42.8 F (7°C/6°C) LWC 95°F (35°C) (DT = 9°F (5°C)
* (4) The sound pressure level is measured via a microphone at 3.23 ft (1 m) from the unit. It is a relative value, depending on the distance and
acoustic environment. The sound pressure level mentioned is valid for pump medium speed.
* (5) 59°F~77°F (15°C~25°C): BUH only, no heat pump operation = during commissioning
* (6) Including piping + PHE + backup heater / excluding expansion vessel
NOTES:
Electrical Specifiations
Type
Electric heater
(optional)
Phase
Power supply (1),(2)
Current
Voltage range
Wiring connections
6VJU
1~
1~
Frequency
Hz
60
60
Voltage
V
208/230
208/230
Minimum Circuit Amps (MCA)
A
14.3
28.6
Maximum Overcurrent Protection (MOP)
A
20
Minimum
Maximum
30
V
187
V
253
for power supply backup heater
quantity of wires
3G
for power supply connection to
type of wires
quantity of wires
Note (3)
3G
optional domestic hot water tank + Q2L
for connection with RST
for connection with A3P
for connection with M2S
for connection with M3S
for connection of bottom plate heater
NOTES
3VJU
type of wires
quantity of wires
Note (3) & (4)
Note (7)
type of wires
Note (7)
quantity of wires
Note (6)
type of wires
quantity of wires
type of wires
quantity of wires
type of wires
quantity of wires
type of wires
Note (3) & (5)
3G
Note (3) & (5)
3G or 4G
Note (3) & (5)
2
Note (3)
* (1) Above mentioned power supply of hydrobox is fro backup heater only. The Switch box & pump of the hydrobox are supplied via the outdoor
unit. The optional domestic hot water tank has a separate power supply.
* (2) Optional electric heater has 2 capacity steps except for the 3VJU model which has only 1 capacity step.
* (3) Select diameter and type according to local laws and regulations.
* (4) For more details of the voltage range and current, refer to installation manual EKHBH/X054BA*
* (5) Voltage: 24V / Maximum current: 100mA / Minimum AWG 18 (0.77MM2)
* (6) Depends on thermostat type; refer to Installation Manual for EKHBH/X054BA*
* (7) Wire included in Option EKHWS*
32
Specifications - Hydrobox
DACA-EEDEN09-720
Dimensional Dwg. & Center of Gravity- Hydrobox
3. Dimensional Dwg. & Center of Gravity- Hydrobox
33
Dimensional Dwg. & Center of Gravity- Hydrobox
DACA-EEDEN09-720
Piping Diagram - Hydrobox
4. Piping Diagram - Hydrobox
34
Piping Diagram - Hydrobox
DACA-EEDEN09-720
Wiring Diagram - Hydrobox
5. Wiring Diagram - Hydrobox
5.1
35
EKHB(H/X)054BA3VJU
Wiring Diagram - Hydrobox
DACA-EEDEN09-720
5.2
36
Wiring Diagram - Hydrobox
EKHB(H/X)054BA6VJU
Wiring Diagram - Hydrobox
DACA-EEDEN09-720
External Connection Diagram - Hydrobox
6. External Connection Diagram - Hydrobox
37
External Connection Diagram - Hydrobox
DACA-EEDEN09-720
Condensate Instructions - Hydrobox
7. Condensate Instructions - Hydrobox
38
Condensate Instructions - Hydrobox
DACA-EEDEN09-720
Application Examples - Hydrobox
8. Application Examples - Hydrobox
TYPICAL APPLICATION EXAMPLES
Application 2
The application examples given below are for illustration purposes
only.
Application 1
Space heating only application without room thermostat connected to
the indoor unit. The temperature in each room is controlled by a valve
on each water circuit. Domestic hot water is provided through the
domestic hot water tank which is connected to the indoor unit.
Space heating only application with the room thermostat connected
to the indoor unit.
1
2
3
4
5
8
6
T1
9
T2
T3
M
T
1
2
3
4
M1
5
M2
M3
6
7
11 12
FHL1
FHL2
FHL3
10
FHL1
7
FHL2
FHL3
1
Outdoor unit
2
Indoor unit
3
Heat exchanger
4
Pump
5
Shut-off valve
6
7
1
Outdoor unit
Collector (field supply)
2
Indoor unit
9
By-pass valve
(field supply)
10
Domestic hot water tank
(optional)
Shut-off valve
3
Heat exchanger
FHL1..3
Floor heating loop
4
Pump
T
Room thermostat
(optional)
5
Shut-off valve
11
Booster heater
6
Collector (field supply)
12
Heat exchanger coil
7
Shut-off valve
8
Motorised 3-way valve
(delivered with
domestic hot water
tank)
Pump operation and space heating
When the room thermostat (T) is connected to the indoor unit, the
pump (4) will operate when there is a heating request from the room
thermostat, and the outdoor unit will start operating to achieve the
target leaving water temperature as set on the user interface.
When the room temperature is above the thermostat set point, the
outdoor unit and pump will stop operating.
Make sure to connect the thermostat wires to the correct
terminals (see "Connection of the thermostat cable" on
page 18) and to configure the DIP switch toggle switches
correctly (see "Room thermostat installation configuration"
on page 22).
FHL1..3
Floor heating loop
T1..3
Individual room
thermostat (optional)
M1..3
Individual motorised
valve to control loop
FHL1 (field supply)
Pump operation
With no thermostat connected to the indoor unit (2), the pump (4) can
be configured to operate either as long as the indoor unit is on, or
until the required water temperature is reached.
NOTE
Details on pump configuration can be found under
"Pump operation configuration" on page 23.
Space heating
The outdoor unit (1) will operate to achieve the target leaving water
temperature as set on the user interface.
NOTE
When circulation in each space heating loop (FHL1..3)
is controlled by remotely controlled valves (M1..3), it is
important to provide a by-pass valve (9) to avoid the
flow switch safety device from being activated.
The by-pass valve should be selected as such that at
all time the minimum water flow as mentioned under
"Water pipework" on page 14 is guaranteed.
It is recommended to select a pressure difference
controlled by-pass valve.
Installation manual
4
39
EKHBH/X054BA
Indoor unit for air to water heat pump system
4PW54216-1
Application Examples - Hydrobox
DACA-EEDEN09-720
1
Outdoor unit
2
Indoor unit
3
Heat exchanger
4
Pump
5
Shut-off valve
6
Collector (field supply)
7
Shut-off valve
9
By-pass valve (field
supply)
13
Motorised 2-way valve
to shut off the floor
heating loops during
cooling operation (field
supply)
Application Examples - Hydrobox
14
Motorised 2-way valve for
activation of the room
thermostat (field supply)
FCU1..3
Fan coil unit with
thermostat (optional)
FHL1..3
Floor heating loop
T
Heating only room
thermostat (optional)
T4..6
Individual room
thermostat for fan coil
heated/cooled room
(optional)
Pump operation
With no thermostat connected to the indoor unit (2), the pump (4) can
be configured to operate either as long as the indoor unit is on, or
until the required water temperature is reached.
NOTE
Details on pump configuration can be found under
"Pump operation configuration" on page 23.
Application 5
Space heating with an auxiliary boiler (alternating operation)
Space heating application by either the Daikin indoor unit or by an
auxiliary boiler connected in the system. The decision whether either
the EKHB* indoor unit or the boiler will operate can be achieved by
an auxiliary contact or an EKHB* indoor controlled contact.
The auxiliary contact can e.g. be an outdoor temperature thermostat,
an electricity tariff contact, a manually operated contact, etc. See
"Field wiring configuration A" on page 7.
The EKHB* indoor unit controlled contact (also called 'permission
signal for the auxiliary boiler") is determined by the outdoor
temperature (thermistor located at the outdoor unit). See "Field wiring
configuration B" on page 7.
Bivalent operation is only possible for space heating operation, not
for the domestic water heating operation. Domestic hot water in such
an application is always provided by the domestic hot water tank
which is connected to the Daikin indoor unit.
The auxiliary boiler must be integrated in the piping work and in the
field wiring according to the illustrations below.
CAUTION
Space heating and cooling
According to the season, the customer will select heating or cooling
through the user interface on the indoor unit.
The outdoor unit (1) will operate in heating mode or cooling mode to
achieve the target leaving water temperature.
■
Be sure that the boiler and the integration of the boiler
in the system is in accordance with relevant local laws
and regulations.
■
Daikin can not be put responsible for incorrect or
unsafe situations in the boiler system.
With the unit in heating mode, the 2-way valve (13) is open. Hot water
is provided to both the fan coil units and the floor heating loops.
With the unit in cooling mode, the 2-way valve (13) is closed to
prevent cold water running through the floor heating loops (FHL).
1
2
3
4
5
8
18
17
6
M
When closing several loops in the system by remotely
controlled valves, it might be required to install a by-pass
valve (9) to avoid the flow switch safety device from being
activated. See also "Application 2" on page 4.
Wiring of the 2-way valve (13) is different for a NC (normal
closed) valve and a NO (normal open) valve! Make sure to
connect to the correct terminal numbers as detailed on the
wiring diagram.
7
16 15 17
The ON/OFF setting of the heating/cooling operation is done by the
user interface on the indoor unit.
10 11
FHL1
FHL2
FHL3
12
1
Outdoor unit
11
Heat exchanger coil
2
Indoor unit
12
3
Heat exchanger
Domestic hot water tank
(optional)
4
Pump
15
Boiler (field supply)
5
Shut-off valve
16
6
Collector (field supply)
Aquastat valve
(field supply)
7
Shut-off valve
17
8
Motorised 3-way valve
(delivered with the
domestic hot water
tank)
Shut-off valve
(field supply)
18
Non-return valve
(field supply)
10
40
Booster heater
FHL1...3
Floor heating loop
(field supply)
Application Examples - Hydrobox
DACA-EEDEN09-720
Application Examples - Hydrobox
Field wiring configuration A
NOTE
L
H
■
Com
EKHB*/auto /Boiler
EKHB*
X2M
Boiler
thermostat input
1 2 3 4
X Y
A
K1A
K1A
K2A
K2A
Configuration B
Make sure that the bivalent hysteresis [C-04] has
sufficient differential to avoid frequent changeover
between the EKHB* unit and the boiler. As the
outdoor temperature is measured via the outdoor
unit, air thermistor make sure to install the
outdoor unit in the shade, so that it is not
influenced by the sun.
N
Boiler
thermostat input
Boiler thermostat input
A
Auxiliary contact (normal closed)
H
Heating demand room thermostat (optional)
K1A
Auxiliary relay for activation of EKHB* unit (field
supply)
K2A
Auxiliary relay for activation of boiler (field supply)
Frequent switching may cause corrosion of the
boiler in an early stage. Contact the manufacturer
of the boiler.
Field wiring configuration B
■
EKRP1HB
EKHB*
X2M
1 2 3 4
KCR
X1 X2
K1A
K1A
C Com H
EKRTW*
X Y
Boiler
thermostat input
Boiler
thermostat input
Boiler thermostat input
C
Cooling demand room thermostat (optional)
H
Heating demand room thermostat (optional)
Com
Common room thermostat (optional)
K1A
Auxiliary relay for activation of bolier unit
(field supply)
KCR
Permission signal for the auxiliary boiler
Operation
■
Configuration A
When the room thermostat requests heating, either the EKHB*
unit or the boiler starts operating, depending on the position of
the auxiliary contact (A).
■
Configuration B
When the room thermostat requests heating, either the EKHB*
unit or the boiler starts operating, depending on the outdoor
temperature (status of "permission signal for the auxiliary
boiler").
When the permission is given towards the boiler, the space
heating operation by the EKHB* unit will be automatically
switched off.
For more details see field setting [C-02~C-04].
Configuration A
Make sure that auxiliary contact (A) has sufficient
differential or time delay so as to avoid frequent
changeover between the EKHB* unit and the
boiler. If the auxiliary contact (A) is an outdoor
temperature thermostat, make sure to install the
thermostat in the shade, so that it is not
influenced or turned ON/OFF by the sun.
During heating operation of the EKHB* unit, the
unit will operate so as to achieve the target
leaving water temperature as set on the user
interface. When weather dependent operation is
active, the water temperature is determined
automatically depending on the outdoor
temperature.
During heating operation of the boiler, the boiler
will operate so as to achieve the target leaving
water temperature as set on the boiler controller.
Never set the target leaving water temperature set
point on the boiler controller above 131°F (55°C).
■
NOTE
Make sure to only have 1 expansion vessel in the
water circuit. An expansion vessel is already
premounted in the Daikin indoor unit.
Make sure to configure the DIP switch SS2-3 on the
PCB of the EKHB* switchbox correctly. Refer to "Room
thermostat installation configuration" on page 22.
For configuration B: Make sure to configure the field
settings [C-02, C-03 and C-04] correctly. Refer to
"Bivalent operation" on page 32.
CAUTION
Make sure that return water to the EKHB* heat exchanger
never exceeds 131°F (55°C).
For this reason, never put the target leaving water
temperature set point on the boiler controller above 131°F
(55°C) and install an aquastat(a) valve in the return water
flow of the EKHB* unit.
Make sure that the non-return valves (field supply) are
correctly installed in the system.
Make sure that the room thermostat (th) is not frequently
turned ON/OFF.
Daikin shall not be held liable for any damage resulting
from failure to observe this rule.
(a) The aquastat valve must be set for 131°F (55°C) and must operate to close the
return water flow to the unit when the measured temperature exceeds 131°F
(55°C). When the temperature drops to a lower level, the aquastat valve must
operate to open the return water flow to the EKHB* unit again.
Manual permission towards the EKHB* unit on the boiler.
In case only the EKHB* unit should operate in space
heating mode, disable the bivalent operation via setting
[C-02].
In case only the boiler should operate in space heating
mode, increase the bivalent ON temperature [C-03] to
77°F (25°C).
EKHBH/X054BA
Indoor unit for air to water heat pump system
4PW54216-1
41
Installation manual
7
Application Examples - Hydrobox
DACA-EEDEN09-720
Application Examples - Hydrobox
Pump operation and space heating
Application 6
Space heating with room thermostat application through floor heating
loops and fan coil units. The floor heating loops and fan coil units
require different operating water temperatures.
The floor heating loops require a lower water temperature in heating
mode compared to fan coil units. To achive these two set points, a
mixing station is used to adapt the water temperature according to
requirements of the floor heating loops. The fan coil units are directly
connected to the indoor unit water circuit and the floor heating loops
after the mixing station. The control of this mixing station is not done
by the indoor unit.
The operation and configuration of the field water circuit is the
responsibility of the installer.
Daikin only offers a dual set point control function. By this function
two set points can be generated. Depending on the required water
temperature (floor heating loops and/or fan coil units are required)
first set point or second set point can be activated.
B
When the room thermostat for the floor heating loop (T1) and the fan
coil units (T2) are connected to the indoor unit, the pump (4) will
operate when there is a request for heating from T1 and/or T2. The
outdoor unit will start operating to achieve the target leaving water
temperature. The target leaving water temperature depends on which
room thermostat is requesting heating.
Set point
Field setting
Zone A
First
UI
ON
OFF
ON
OFF
Zone B
Second
[7-03]
OFF
ON
ON
OFF
Resulting water temperature
UI
[7-03]
[7-03]
—
Result pump operation
ON
ON
ON
OFF
When the room temperature of both zones is above the thermostat
set point, the outdoor unit and pump will stop operating.
NOTE
7
T1
T2
■
Make sure to connect the thermostat wires to the
correct terminals (see "Overview of the indoor
unit" on page 9).
■
Make sure to configure the field settings [7-02],
[7-03] and [7-04] correctly. Refer to "Dual set point
control" on page 29.
■
Make sure to configure the DIP switch SS2-3 on
the PCB of the EKHBH switch box correctly. Refer
to "Room thermostat installation configuration" on
page 22.
■
The request signals for space heating can be
implemented in two different ways (installer
choice).
- Thermo ON/OFF signal from room thermostat
- Status signal (active/not active) from the
mixing station
■
It is the installers responsibility to make sure no
unwanted situations can occur (e.g. too high
water temperatures towards floor heating loops,
etc.)
■
Daikin does not offer any type of mixing station.
Dual set point control only provides the possibility
to use two set points.
■
When only zone A request heating, zone B will be
fed with water at a temperature equal to the first
set point.
This can lead to unwanted heating of zone B.
■
When only zone B request heating, the mixing
station will be fed with water at a temperature
equal to the second set point.
Depending on the control of the mixing station,
the floor heating loop can still receive water at a
temperature equal to set point of the mixing
station.
FCU1
FCU2
1
2
3
4
FCU3
5
A
NOTE
6
FHL1
8
9
FHL2
FHL3
1
Outdoor unit
8
Shut-off valve
2
Indoor unit
9
Mixing station (field supply)
T1
Room thermostat for zone
A (optional)
T2
Room thermostat for zone
B (optional)
3
Heat exchanger
4
Pump
5
Shut-off valve
6
Collector zone A
(field supply)
7
Collector zone B
(field supply)
FCU1..3
Fan coil unit (optional)
FHL1...3
Floor heating loop
(field supply)
The advantage of the dual set point control is that the heat
pump will/can operate at the lowest required leaving water
temperature when only floor heating is required. Higher
leaving water temperatures are only required in case fan
coil units are operating.
This results in a better performance of the heat pump.
42
Thermo status
Be aware that the actual water temperature through the
floor heating loops depends on the control and setting of
the mixing station.
Application Examples - Hydrobox
DACA-EEDEN09-720
Hydronic Performance - Hydrobox
9. Hydronic Performance - Hydrobox
43
Hydronic Performance - Hydrobox
DACA-EEDEN09-720
Operation Range - Hydrobox
10. Operation Range - Hydrobox
44
Operation Range - Hydrobox
DACA-EEDEN09-720
Monobloc - EDLQ / EBLQ
1. Monobloc - EDLQ / EBLQ
1.1
Features
•
Heating only (EDLQ) and reversible (EBLQ) monobloc with base pan heater
•
Inverter operated compressor
•
H2O piping between outdoor unit and indoor heating appliances
•
Freeze protection of hydronic parts
•
Cost effective alternative to a fossil fuel boiler
•
Interface control with field selectable options that include dual setpoint (heating & cooling), quiet mode, DHW
priority settings, and schedule timer.
•
Low energy bills and low CO2 emissions
•
Easy to install
•
Total solution for year round comfort
•
Anti-corrosion treatment on outdoor coil
Monobloc
The monobloc unit is designed for outdoor installations. These units are used for both heating and cooling applications
and can be combined with fan coil units, floor heating applications, low temperature radiators, optional Daikin domestic
hot water tank, and optional Daikin solar kit.
The unit range consists of two main versions: a heating only version (EDLQ) and a heating/cooling version (EBLQ).
Both versions are delivered with an integrated backup heater for additional heating capacity during cold outdoor
temperatures. The backup heater also sesrves as a backup in the event malfunctioning of the unit occurs, along with
freeze protection of the outside water piping during winter climates.
45
Monobloc - EDLQ / EBLQ
Specifications  EDLQ  Heat Only
DACA-EEDEN09-720
2. Specifications  EDLQ  Heat Only
2-1
NOMINAL CAPACITY AND NOMINAL INPUT
Condition 1
(Floor heating)
Condition 2
(Fan Coil)
EDLQ036BA6VJU
EDLQ048BA6VJU
EDLQ054BA6VJU
Heating capacity
Nominal
kBTU/hr
38.21
47.77
54.59
Heating PI
Nominal
kW
2.53
3.33
3.93
COP
Nominal
4.42
4.2
4.07
Heating capacity
Nominal
kBTU/hr
37.07
44.17
51.39
Heating PI
Nominal
kW
3.43
3.98
4.75
COP
Nominal
3.25
3.25
3.17
Condition 1: heating Ta DB/WB 44.6 / 42.8°F (7°C/6°C) - LWC 95°F (35°C)T=9°F (5°C)
Notes
Condition 2: heating Ta DB/WB 44.6 / 42.8°F (7°C/6°C) - LWC 113°F (45°C) (T=9°F (5°C))
2-2
TECHNICAL SPECIFICATIONS
Casing
EDLQ036BA6VJU
Colour
Unit
Packing
Weight
Packing
EDLQ054BA6VJU
Ivory white
Material
Dimensions
EDLQ048BA6VJU
Painted galvanised steel
Height
in (mm)
Width
in (mm)
Depth
in (mm)
Height
in (mm)
55-7/8 (1,418)
56-1/2 (1,435)
15-1/32 (382)
15-1/32 (382)
15-1/32 (382)
61-1/4 (1,557)
Width
in (mm)
Depth
in (mm)
16-7/8 (430)
59-1/16 (1,500)
16-7/8 (430)
16-7/8 (430)
Unit
lb (kg)
397 (180)
397 (180)
397b (180)
Packed unit
lb (kg)
441 (200)
441 (200)
441 (200)
Material
Wood
Carton
Plastic foil
Weight
Operation Range
(2, 4)
Sound Level (1)
(nominal)
Sound Level (Night
quiet)
Refrigerant
lb (kg)
44 lb (20)
44 lb (20)
44 lb (20)
Min
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
Max
°F (°C)
95 (35)
95 (35)
95 (35)
Heating - Waterside Min
°F (°C)
59 (15)
59 (15)
59 (15)
Max
°F (°C)
131 (55)
131 (55)
131 (55)
Domestic hot water Min
-Ambient
Max
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
°F (°C)
109.4 (43)
109.4 (43)
109.4 (43)
Heating - Ambient
Domestic hot water Min
- Waterside
Max
°F (°C)
77 (25)
77 (25)
77 (25)
°F (°C)
176 (80)
176 (80)
176 (80)
Heating
Sound
Power
dBA
64
64
66
Sound
Pressure
dBA
51
51
52
Sound
Pressure
dBA
42
42
43
6.5 (2.95)
6.5 (2.95)
Heating
Type
Charge
R-410A
lb (kg)
Control
Nr of Circuits
Refrigerant Oil
1
Type
Charged Volume
1
oz (l)
34 (1.0 l)
34 (1.0 l)
Pressure equalising
Defrost Control
Sensor for outdoor heat exchanger temperature
Safety Devices
1
Daphne FVC68D
Defrost Method
Capacity Control Method
6.5 (2.95)
Electronic expansion valve
34 (1.0 l)
Inverter controlled
High pressure switch
Fan motor thermal protector
Fuse
46
Specifications  EDLQ  Heat Only
Specifications  EDLQ  Heat Only
DACA-EEDEN09-720
2-2
TECHNICAL SPECIFICATIONS
EDLQ036BA6VJU
EDLQ048BA6VJU
EDLQ054BA6VJU
Notes
(1) The sound pressure level is measured via a microphone at a certain distance from the unit. It is a relative value depending on the distance and acoustic environment. Refer to
sound spectrum drawing for more information.
(2) 59°77°F (15°25°C): BUH only, no heat pump operation = during commisioning
(5) including piping + PHE + back-up heater / excluding expansion vessel
(4) E(D)(B)L* model can reach -4°F (-20°C)
2-3
MAIN COMPONENTS
Air heat exchanger
Specifications
Length
EDLQ036BA6VJU
EDLQ048BA6VJU
EDLQ054BA6VJU
33-3/4 (857)
33-3/4 (857)
33-3/4 (857)
2
2
2
in (mm)
1/16 (1.4)
1/16 (1.4)
1/16 (1.4)
5
5
5
ft² (m²)
12.17 (1.131)
12.17 (1.131)
12.17 (1.131)
60
60
in (mm)
Nr of Rows
Fin pitch
Nr of Passes
Face area
Nr of Stages
60
Tube type
Fin
Hi-XSS
Type
WF fin
Treatment
Fan
Anti-corrosion treatment (PE)
Type
Propeller
Quantity
Air Flow Rate
(nominal at 230V)
Heating
Fan
Discharge direction
Motor
High
cfm (m³/min)
2
2
2
3178 (90)
3178 (90)
3178 (90)
Horizontal
Quantity
2
Model
Motor
Fan
Speed (nominal)
Motor
Steps
8
8
8
rpm
760
760
760
Output
W
70
70
70
Direct drive
Quantity
Motor
1
Model
Motor Output
Crankcase Heater
Type
Output
2,200
Inverter driven
W
Heating
Power input
Water side Heat
exchanger
33
PSI (kPa)
W
2
2
2
6.31 PSI (43.5 kPa)
5 PSI (35 kPa)
210
210
210
Brazed plate
Quantity
gal (l)
1
1
1
0.27 (1.01)
0.27 (1.01)
0.27 (1.01)
Water flow rate Min.
gpm (l/min)
4.23 (16)
4.23 (16)
4.23 (16)
Water flow rate Nom. Heating
gpm (l/min)
8.5 (32.1)
10.6 (40.1)
12.1 (45.9)
Water flow rate Max.
gpm (l/min)
15.3 (58)
15.3 (58)
15.3 (58)
Insulation material
Water filter
Foamed synthetic elastomer
Volume
gal (l)
2.64 (10)
2.64 (10)
Maximum water pressure
PSI (bar)
43.5 (3)
43.5 (3)
43.5 (3)
Pre pressure
PSI (bar)
14.5 (1.0)
14.5 (1.0)
14.5 (1.0)
Diameter perforations
in (mm)
1/32 (1)
1/32 (1)
1/32 (1)
Material
47
33
7.61 PSI (52.5 kPa)
Type
Water volume
Expansion vessel
33
Water cooled
Nr. of speed
Nominal ESP unit
1
Hermetically sealed scroll compressor
W
Starting Method
Pump
1
JT100G-VD
Type
Motor
2
Heating
Drive
Compressor
2
Brushless DC
2.64 (10)
Brass
Specifications  EDLQ  Heat Only
Specifications  EDLQ  Heat Only
DACA-EEDEN09-720
2-3
MAIN COMPONENTS
Water circuit
EDLQ036BA6VJU
Piping connections
EDLQ048BA6VJU
inch
Piping
inch
Safety valve
PSI (bar)
1-1/4
43.5 (3)
43.5 (3)
Manometer (Pressure Gauge)
Yes
Drain valve / Fill valve
yes
Shut off valve
yes
Air purge valve
gal (l)
Main Power
EDLQ036BA6VJU
EDLQ054BA6VJU
1
1
1
60
60
60
Voltage
V
208/230
208/230
208/230
Minimum
V
-10%
V
+10%
Compressor
Rated Load Amps (RLA)
A
23.4
23.4
23.4
Total
Full Load Amps (FLA)
A
26.5
26.5
26.5
MCA
A
26.5
26.5
26.5
MOP
A
30
30
30
Wiring
connections
For power supply
compressor
component
Power supply hydronic
component
Current back-up
heater
Type
Current back-up heater
Power Supply
Current
EDLQ048BA6VJU
Hz
Maximum
Current
145 (5.5)
VJ
Phase
Voltage Range
145 (5.5)
Name
Frequency
48
145 (5.5)
ELECTRICAL SPECIFICATIONS
Power supply
compressor component
43.5 (3)
yes
Total water volume (3)
2-4
EDLQ054BA6VJU
1-1/4 BSPP male
Installation Instruction
Electric 6kW
Phase
1~
Frequency
Hz
60
60
60
Voltage
V
208/230
208/230
208/230
Minimum Circuit
Amps (MCA)
A
28.6
28.6
28.6
Maximum
Overcurrent
Protection (MOP)
A
30
30
30
Specifications  EDLQ  Heat Only
Specifications  EDLQ  Heat Only
DACA-EEDEN09-720
2-4
ELECTRICAL SPECIFICATIONS
Power supply
hydronic component
Voltage range
Wiring
connections
V
Maximum
V
Connection type
Quantity of wires
Type of wires
Connection type
Quantity of wires
EDLQ048BA6VJU
EDLQ054BA6VJU
-10%
+10%
for power supply hydraulic compartment
2G
Select diameter and type according to national and local regulations
for power supply connection to optional sanitary tank + Q2L
3G
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Connection type
for connection with R5T
Quantity of wires
Wire included in option EKHWS*
Type of wires
Wire included in option EKHWS*
Connection type
for connection with A3P
Quantity of wires
Depends on thermostat type, refer to installation manual
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Connection type
Quantity of wires
for connection with M2S
3G
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Connection type
Quantity of wires
Notes
EDLQ036BA6VJU
Minimum
for connection with M3S
3G or 4G
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Power supply compressor compartment is for compressor, fan, pump and
controller
Power supply hydraulic compartment is for the electric heater. The optional
domestic warm water tank has a separate power supply.
Installer can reduce capacity of the heater from 20,491 to 10,245 BTU/hr
(6 to 3kW). The current is then reduced from 26 to 13A. Instructions see
installation manual.
Installer can reduce capacity of the heater from 20,491 to 11,953 BTU/hr
(6 to 3kW). The current is then reduced from 8.7 to 5A. Instructions see
installation manual.
Standard for safety heating and cooling equipment: UL1995/CSA (U&C)
C22.2 #236
49
Specifications  EDLQ  Heat Only
DACA-EEDEN09-720
Capacity Tables  EDLQ  Heat Only
3. Capacity Tables  EDLQ  Heat Only
Peak value does not include capacity drop during frosting and defrosting periods.
Integrated value takes into consideration the capacity drop during frosting and defrosting periods.
50
Capacity Tables  EDLQ  Heat Only
Specifications  EBLQ Heat Pump
DACA-EEDEN09-720
4. Specifications  EBLQ Heat Pump
4-1
NOMINAL CAPACITY AND NOMINAL INPUT
Condition 1
(Floor Heating)
Condition 2
(Fan Coil)
EBLQ036BA6VJU
EBLQ048BA6VJU
EBLQ054BA6VJU
Heating capacity
Nominal
kBTU/hr
38.21
47.77
54.59
Cooling capacity
Nominal
kBTU/hr
43.83
54.57
57.07
Heating PI
Nominal
kW
2.53
3.33
3.93
Cooling PI
Nominal
kW
3.91
5.79
6.43
COP
Nominal
4.54
4.37
4.22
EER
Nominal
11.21
9.42
8.88
Heating capacity
Nominal
kBTU/hr
37.07
44.17
51.39
Cooling capacity
Nominal
kBTU/hr
34.17
42.69 (12.50)
44.74 (13.10)
Heating PI
Nominal
kW
3.43
3.98
4.75
Cooling PI
Nominal
kW
3.72
5.42
5.97
COP
Nominal
3.37
3.35
3.26
EER
Nominal
9.17
7.87
7.49
Condition 1: cooling Ta 95°F (35°C) - LWE 64.4°F (18°C) (T=41°F (5°C); heating Ta DB/WB 44.6 /
42.8°F (7°C/6°C) - LWC 95°F (35°C) T=41°F (5°C)
Notes
Condition 2: cooling Ta 95°F (35°C) - LWE 7°C (T=5°C); heating Ta DB/WB 44.6 / 42.8°F (7°C/
6°C) - LWC 113°F (45°C) (T=41°F (5°C))
4-2
TECHNICAL SPECIFICATIONS
Casing
Colour
Dimensions
Unit
EBLQ036BA6VJU
Weight
Packing
EBLQ054BA6VJU
Ivory white
Material
Packing
EBLQ048BA6VJU
Painted galvanised steel
Height
in (mm)
Width
in (mm)
Depth
in (mm)
Height
in (mm)
55-7/8 (1,418)
56-1/2 ( mm)
15-1/32 (382)
15-1/32 (382)
15-1/32 (382)
61-1/4 (1,557)
Width
in (mm)
Depth
in (mm)
16-7/8 (430)
59-1/16 (1,500)
16-7/8 (430)
Unit
lb (kg)
397 (180)
397 (180)
397 (180)
Packed unit
lb (kg)
441 (200)
441 (200)
441 (200)
Material
16-7/8 (430)
Wood
Carton
Plastic foil
Weight
Operation Range
(2 ,4)
Heating - Ambient
44 (20)
44 (20)
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
95 (35)
Max
°F (°C)
95 (35)
95 (35)
°F (°C)
59 (15)
59 (15)
59 (15)
Max
°F (°C)
131 (55)
131 (55)
131 (55)
Min
°F (°C)
50 (10)
50 (10)
50 (10)
Max
°F (°C)
114.8 (46)
114.8 (46)
114.8 (46)
Cooling - Waterside Min
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
Max
°F (°C)
71.6 (22)
71.6 (22)
71.6 (22)
Domestic hot water
-Ambient
Min
°F (°C)
-4 (-20)
-4 (-20)
-4 (-20)
Max
°F (°C)
109.4 (43)
109.4 (43)
109.4 (43)
Domestic hot water
- Waterside
Min
°F (°C)
77 (25)
77 (25)
77 (25)
Max
°F (°C)
176 (80)
176 (80)
176 (80)
Heating
Sound
Power
dBA
64
64
66
Sound
Pressure
dBA
51
51
52
Sound
Power
dBA
65
66
69
Sound
Pressure
dBA
50
52
54
Cooling
51
44 (20)
Heating - Waterside Min
Cooling - Ambient
Sound Level
(nominal) (1)
Min
lb (kg)
Specifications  EBLQ Heat Pump
Specifications  EBLQ Heat Pump
DACA-EEDEN09-720
4-2
TECHNICAL SPECIFICATIONS
Sound Level (Night
quiet)
Refrigerant
EBLQ036BA6VJU
EBLQ048BA6VJU
EBLQ054BA6VJU
Heating
Sound
Pressure
dBA
42
42
43
Cooling
Sound
Pressure
dBA
45
45
46
Type
R-410A
Charge
lb (kg)
6.5 (2.95)
6.5 (2.95)
Control
Nr of Circuits
Refrigerant Oil
6.5 (2.95)
Electronic expansion valve
1
1
Type
1
Daphne FVC68D
Charged Volume
oz (l)
34 oz (1.0 l)
34 oz (1.0 l)
Defrost Method
Pressure equalising
Defrost Control
Sensor for outdoor heat exchanger temperature
Capacity Control Method
34 oz (1.0 l)
Inverter controlled
Safety Devices
High pressure switch
Fan motor thermal protector
Fuse
Notes
(1) The sound pressure level is measured via a microphone at a certain distance from the unit. It is a relative value depending on the distance and acoustic environment.
Refer to sound spectrum drawing for more information.
(2) 15°-25°C: BUH only, no heat pump operation = during commisioning
(3) Including piping + PHE + back-up heater / excluding expansion vessel
(4) E(D)(B)L* model can reach -4°F (-20°C)
4-3
MAIN COMPONENTS
Air heat exchanger
Specifications
Length
EBLQ036BA6VJU
EBLQ048BA6VJU
EBLQ054BA6VJU
33-3/4 (857)
33-3/4 (857)
33-3/4 (857)
2
2
2
in (mm)
1/16 (1.4)
1/16 (1.4)
1/16 (1.4)
5
5
5
ft² (m²)
12.17 (1.131)
12.17 (1.131)
12.17 (1.131)
60
60
in (mm)
Nr of Rows
Fin pitch
Nr of Passes
Face area
Nr of Stages
60
Tube type
Fin
Hi-XSS
Type
WF fin
Treatment
Fan
Anti-corrosion treatment (PE)
Type
Propeller
Quantity
2
2
2
3178 (90)
3178 (90)
3531 (100)
3426 (97)
Air Flow Rate
(nominal at 230V)
Heating
High
cfm (m³/min)
3178 (90)
Cooling
High
cfm (m³/min)
3390 (96)
Fan
Discharge direction
Motor
Horizontal
Quantity
2
Model
Motor
Speed (nominal)
Steps
Motor
8
8
8
760
760
760
Cooling
rpm
780
780
780
Output
W
70
70
70
Drive
Compressor
Direct drive
Quantity
Motor
1
Model
Motor Output
52
Output
1
Hermetically sealed scroll compressor
W
2,200
Starting Method
Crankcase Heater
1
JT100G-VD
Type
Motor
2
rpm
Heating
Fan
2
Brushless DC
Inverter driven
W
33
33
33
Specifications  EBLQ Heat Pump
Specifications  EBLQ Heat Pump
DACA-EEDEN09-720
4-3
MAIN COMPONENTS
Pump
EBLQ036BA6VJU
Type
Heating
Cooling
Power input
Water side Heat
exchanger
2
2
2
PSI (kPa)
7.61 (52.5)
6.31 (43.5)
5 (35)
PSI (kPa)
8.11 (55.9)
7.12 (49.1)
6.79 (46.8)
210
210
210
W
Type
Brazed plate
Quantity
Water volume (3)
gal (l)
Water flow rate Min.
Water flow rate Nom.
Heating
Cooling
1
1
1
0.27 (1.01)
0.27 (1.01)
0.27 (1.01)
gpm/min (l/min)
423 (16)
423 (16)
423 (16)
gpm/min (l/min)
848 (32.1)
10.49 (40.1)
12.13 (45.9)
gpm/min (l/min)
9.72 (36.8)
12.13 (45.9)
12.68 (48)
gpm/min (l/min)
15.32 (58)
15.32 (58)
15.32 (58)
Volume
gal (l)
2.64 (10)
2.64 (10)
Maximum water pressure
PSI (bar)
43.5 (3)
43.5 (3)
43.5 (3)
Pre pressure
PSI (bar)
14.5 (1.0)
14.5 (1.0)
14.5 (1.0)
Diameter perforations
in (mm)
1/32 (1)
1/32 (1)
1/32 (1)
Water flow rate Max.
Insulation material
Expansion vessel
Water filter
Foamed synthetic elastomer
Material
Water circuit
Piping connections
inch
Piping
inch
Safety valve
PSI (bar)
1-1/4 (MALE) BSP
1-1/4
43.5 (3)
Yes
Drain valve / Fill valve
yes
Shut off valve
yes
Main Power
145 (5.5)
EBLQ036BA6VJU
Name
Current back-up
heater
Current back-up
heater
Power Supply
Current
EBLQ048BA6VJU
145 (5.5)
EBLQ054BA6VJU
1
1
1
Hz
60
60
60
Voltage
V
208/230
208/230
208/230
Minimum
V
Maximum
V
Rated Load Amps (RLA)
A
23.4
23.4
23.4
Full Load Amps (FLA)
A
26.5
26.5
26.5
MCA
A
26.5
26.5
26.5
MOP
A
30
30
30
-10%
+10%
Wiring connections For power supply compressor
component
Power supply
hydraulic component
145 (5.5)
VJ
Phase
Frequency
Current
43.5 (3)
yes
gal (l)
ELECTRICAL SPECIFICATIONS
Voltage range
Installation Instruction
Type
Electric 6kW
Phase
1~
Frequency
Hz
60
60
60
Voltage
V
208/230
208/230
208/230
28.6
28.6
28.6
30
30
30
Minimum Circuit Amps (MCA) A
Maximum Overcurrent
Protection (MOP)
53
43.5 (3)
Manometer
Total water volume (3)
Power supply
compressor
component
2.64 (10)
Brass
Air purge valve
4-4
EBLQ054BA6VJU
Water cooled
Nr. of speed
Nominal ESP unit
EBLQ048BA6VJU
A
Specifications  EBLQ Heat Pump
Specifications  EBLQ Heat Pump
DACA-EEDEN09-720
4-4
ELECTRICAL SPECIFICATIONS
Power supply
hydronic component
Voltage range
V
Maximum
V
Wiring connections Connection type
Quantity of wires
Type of wires
Connection type
Quantity of wires
EBLQ048BA6VJU
EBLQ054BA6VJU
-10%
+10%
for power supply hydraulic compartment
3G
Select diameter and type according to national and local regulations
for power supply connection to optional sanitary tank + Q2L
3G
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual
Connection type
for connection with R5T
Quantity of wires
Wire included in option EKHWS*
Type of wires
Wire included in option EKHWS*
Connection type
for connection with A3P
Quantity of wires
Depends on thermostat type, refer to installation manual
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Connection type
Quantity of wires
for connection with M2S
3G
Type of wires
Select diameter and type according to national and local regulations
Type of wires
For more details on voltage range and current refer to installation manual.
Connection type
Quantity of wires
Type of wires
Type of wires
Notes
EBLQ036BA6VJU
Minimum
for connection with M3S
3G or 4G
Select diameter and type according to national and local regulations
For more details on voltage range and current refer to installation manual.
Power supply compressor compartment is for compressor, fan, pump and controller
Installer can reduce capacity of the heater from 20,491 to 10,245 BTU/hr (6 to 3kW). The
current is then reduced from 26 to 13A. Instructions see installation manual.
Installer can reduce capacity of the heater from 6 to 3.5kW. The current is then reduced
from 8.7 to 5A. Instructions see installation manual.
Power supply hydraulic compartment is for the electric heater. The optional domestic warm
water tank has a separate power supply.
Standard for safety heating & cooling equipment; UL1995 / CSA (U&C) C22.2 #236
54
Specifications  EBLQ Heat Pump
DACA-EEDEN09-720
Capacity Tables  EBLQ  Heating
5. Capacity Tables  EBLQ  Heating
Peak value does not include capacity drop during frosting and defrosting periods.
Integrated value takes into consideration the capacity drop during frosting and defrosting periods.
55
Capacity Tables  EBLQ  Heating
DACA-EEDEN09-720
Capacity Tables  EBLQ Cooling
6. Capacity Tables  EBLQ Cooling
Symbols:
CC
HC
PI
LWE
LWC
Tamb
Cooling Capacity @ maximum operating frequency, BTU/h
Heating Capacity @ maximum operating frequency, BTU/h
Cooling Power Input (kW), Heating Power Input (kBTU/h measured according to Eurovent 6/C003-2006 (kW)/EN14511
Leaving Water evaporator temperature (Cooling)
Leaving Water condenser temperature (Heating)
Outdoor Ambient temperature, RH = 85%
Conditions:
Cooling Capacity BTU/h and valid for chilled water range T = 5-150F (3-80C)
Heating Capacity is according to Eurovent 6/C/003-2006 (kW) and valid for heating water range T = 5-150F (3-80C)
Power Input is total of indoor and outdoor unit, except the circulation pump; (90W per EN14511)
56
Capacity Tables  EBLQ Cooling
DACA-EEDEN09-720
Dimensional Drwg. & Center of Gravity - Monobloc
7. Dimensional Drwg. & Center of Gravity - Monobloc
57
Dimensional Drwg. & Center of Gravity - Monobloc
DACA-EEDEN09-720
Piping Diagram - Monobloc
8. Piping Diagram - Monobloc
58
Piping Diagram - Monobloc
DACA-EEDEN09-720
Wiring Diagram - Monobloc
9. Wiring Diagram - Monobloc
59
Wiring Diagram - Monobloc
DACA-EEDEN09-720
9.1
60
Wiring Diagram - Monobloc
Wiring Diagram
Wiring Diagram - Monobloc
DACA-EEDEN09-720
9.2
61
Wiring Diagram - Monobloc
External Connection Diagram - Monobloc
Wiring Diagram - Monobloc
DACA-EEDEN09-720
Sound Data - Monobloc
10. Sound Data - Monobloc
10.1 Sound Pressure Spectrum - Normal Operation
10.2 Sound Pressure Night Quiet Mode
62
Sound Data - Monobloc
DACA-EEDEN09-720
Application Examples - Monobloc
11. Application Examples - Monobloc
TYPICAL
APPLICATION EXAMPLES
Application 2
The application examples given below are for illustration purposes
only.
Application 1
Space heating only application without room thermostat connected to
the unit. The temperature in each room is controlled by a valve on
each water circuit. Domestic hot water is provided through the
domestic hot water tank which is connected to the unit.
Space heating only application with a room thermostat connected to
the unit.
I
1
2
3
4
5
6
I
T1
T
1
2
3
7
T2
T3
M
5
4
M1
8
M2
M3
9 FHL1
FHL2
FHL3
FHL1
10
FHL2
FHL3
1
Unit
2
Heat exchanger
3
Pump
4
Shut-off valve
5
Collector (field supply)
FHL1..3
Floor heating loop
(field supply)
T
Room thermostat
(optional)
I
User interface
Unit operation and space heating
When a room thermostat (T) is connected to the unit and when there
is a heating request from the room thermostat, the unit will start
operating to achieve the target leaving water temperature as set on
the user interface.
When the room temperature is above the thermostat set point, the
unit will stop operating.
Make sure to connect the thermostat wires to the correct
terminals (see "Connection of the thermostat cable" on
page 20) and to configure the DIP switch toggle switches
correctly (see "Room thermostat installation configuration"
on page 23).
1
Unit
9
Heat exchanger coil
2
Heat exchanger
10
3
Pump
Domestic hot water tank
(optional)
4
Shut-off valve
5
Collector (field supply)
6
Motorised 3-way valve
(optional)
T1..3
Individual room
thermostat (field supply)
7
By-pass valve
(field supply)
M1..3
8
Booster heater
Individual motorised
valve to control loop
FHL1 (field supply)
FHL1..3
I
Floor heating loop
(field supply)
User interface
Pump operation
With no thermostat connected to the unit (1), the pump (3) can be
configured to operate either as long as the unit is on, or until the
required water temperature is reached.
NOTE
Details on pump configuration can be found under
"Pump operation configuration" on page 23.
Space heating
The unit (1) will operate to achieve the target leaving water
temperature as set on the user interface.
When circulation in each space heating loop (FHL1..3) is
controlled by remotely controlled valves (M1..3), it is
important to provide a by-pass valve (7) to avoid the flow
switch safety device from being activated.
The by-pass valve should be selected as such that at all
time the minimum water flow as mentioned under "Water
pipework" on page 13 is guaranteed.
63
Application Examples - Monobloc
DACA-EEDEN09-720
Application Examples - Monobloc
Domestic water heating
Pump operation and space heating and cooling
When domestic water heating mode is enabled (either manually by
the user, or automatically through a schedule timer) the target
domestic hot water temperature will be achieved by a combination of
the heat exchanger coil and the electrical booster heater.
According to the season, the customer will select cooling or heating
on the room thermostat (T). This selection is not possible by
operating the user interface.
When the domestic hot water temperature is below the user
configured set point, the 3-way valve will be activated to heat the
domestic water by means of the heat pump. In case of large domestic
hot water demand or a high domestic hot water temperature setting,
the booster heater (8) can provide auxiliary heating.
When space heating/cooling is requested by the room thermostat
(T), the pump will start operating and the unit (1) will switch to
"heating mode"/"cooling mode". The unit (1) will start operating to
achieve the target leaving cold/hot water temperature.
In case of cooling mode, the motorised 2-way valve (11) will close as
to prevent cold water running through the floor heating loops (FHL).
It is possible to connect either a 2-wire or a 3-wire 3-way
valve (6). Make sure to fit the 3-way valve correctly. For
more details, refer to "Wiring the 3-way valve" on page 20.
Make sure to connect the thermostat wires to the correct
terminals (see "Connection of the thermostat cable" on
page 20) and to configure the DIP switch toggle switches
correctly (see "Room thermostat installation configuration"
on page 23).
The unit can be configured so that at low outdoor
temperatures the domestic water is exclusively heated
by the booster heater. This assures that the full
capacity of the heat pump is available for space
heating.
NOTE
Details on domestic hot water tank configuration for
low outdoor temperatures can be found under "Field
settings" on page 25, field settings [5-02] to [5-04].
Wiring of the 2-way valve (11) is different for a NC (normal
closed) valve and a NO (normal open) valve! Make sure to
connect to the correct terminal numbers as detailed on the
wiring diagram.
The ON/OFF setting of the heating/cooling operation is done by the
room thermostat and cannot be done by the user interface.
Domestic water heating
Application 3
Space cooling and heating application with a room thermostat
suitable for heating/cooling changeover connected to the unit.
Heating is provided through floor heating loops and fan coil units.
Cooling is provided through the fan coil units only.
Domestic hot water is provided through the domestic hot water tank
which is connected to the unit.
5
Domestic water heating is as described under "Application 2" on
page 7.
Application 4
Space cooling and heating application without a room thermostat
connected to the unit, but with a heating only room thermostat
controlling the floor heating and a heating/cooling thermostat
controlling the fan coil units. Heating is provided through floor heating
loops and fan coil units. Cooling is provided through the fan coil units
only.
I
5
T
1
2
3
4
6
11
FCU1
I
FCU2
M
7
FCU3
M
T4
1
2
3
4
T
M
9
T6
FCU1
FCU2
5
8
T5
11 12
FCU3
M
FHL1
FHL2
FHL3
10
FHL1
FHL2
FHL3
64
1
Unit
10
Domestic hot water tank
1
Unit
2
Heat exchanger
11
Heat exchanger
Pump
Motorised 2-way valve
(field supply)
2
3
4
Shut-off valve
FCU1..3
Fan coil unit (field supply)
3
Pump
5
Collector (field supply)
FHL1..3
4
Shut-off valve
6
Motorised 3-way valve
(optional)
Floor heating loop
(field supply)
5
Collector (field supply)
T
7
By-pass valve (field
supply)
11
Motorised 2-way valve
to shut off the floor
heating loops during
cooling operation (field
supply)
8
Booster heater
9
Heat exchanger coil
I
Room thermostat with
heating/cooling switch
(optional)
User interface
12
Motorised 2-way valve for
activation of the room
thermostat (field supply)
FCU1..3
Fan coil unit with
thermostat (field supply)
FHL1..3
Floor heating loop (field
supply)
T
Heating only room
thermostat (optional)
T4..6
Individual room
thermostat for fan coil
heated/cooled room
(optional)
Application Examples - Monobloc
DACA-EEDEN09-720
Application Examples - Monobloc
p p
CAUTION
With no thermostat connected to the unit (1), the pump (3) can be
configured to operate either as long as the unit is on, or until the
required water temperature is reached.
NOTE
Details on pump configuration can be found under
"Pump operation configuration" on page 23.
■
Be sure that the boiler and the integration of the boiler
in the system is in accordance with relevant local laws
and regulations.
■
Always install a 3-way valve, even if no domestic hot
water tank is installed. This to ensure that the freeze
protection function (see "[4-04] Freeze protection
function" on page 28) can operate when the boiler is
active.
Space heating and cooling
According to the season, the customer will select cooling or heating
through the user interface.
The unit (1) will operate in cooling mode or heating mode to achieve
the target leaving water temperature.
I
1
With the unit in heating mode, the 2-way valve (11) is open. Hot water
is provided to both the fan coil units and the floor heating loops.
M
With the unit in cooling mode, the motorised 2-way valve (11) is
closed to prevent cold water running through the floor heating loops
(FHL).
2
When closing several loops in the system by remotely
controlled valves, it might be required to install a by-pass
valve (7) to avoid the flow switch safety device from being
activated. See also "Application 2" on page 7.
FHL1 FHL2 FHL3
Wiring of the 2-way valve (11) is different for a NC (normal
closed) valve and a NO (normal open) valve! Make sure to
connect to the correct terminal numbers as detailed on the
wiring diagram.
■
1
Motorised 3-way valve
2
Boiler
Daikin can not be put responsible for incorrect or
unsafe situations in the boiler system.
The ON/OFF setting of the heating/cooling operation is done by the
user interface.
I
Application 5
1
2
3
4
6
18
17
5
Space heating with an auxiliary boiler (alternating operation)
Space heating application by either the Daikin unit or by an auxiliary
boiler connected in the system. The decision whether either the
E(D/B)* unit or the boiler will operate can be achieved by an auxiliary
contact or an E(D/B)* indoor controlled contact.
M
The auxiliary contact can e.g. be an outdoor temperature thermostat,
an electricity tariff contact, a manually operated contact, etc. See
"Field wiring configuration A" on page 10.
The E(D/B)* unit controlled contact (also called 'permission signal for
the auxiliary boiler") is determined by the outdoor temperature
(thermistor located at the outdoor unit). See "Field wiring
configuration B" on page 10.
15 17
16
Bivalent operation is only possible for space heating operation, not
for the domestic water heating operation. Domestic hot water in such
an application is always provided by the domestic hot water tank
which is connected to the Daikin unit.
10 11
FHL1
FHL2
The auxiliary boiler must be integrated in the piping work and in the
field wiring according to the illustrations below.
65
12
1
Outdoor unit
2
Heat exchanger
12
Domestic hot water
tank (optional)
3
4
Pump
15
Boiler (field supply)
Shut-off valve
15
5
Collector (field supply)
Aquastat valve
(field supply)
6
Motorised 3-way valve
(delivered with the
domestic hot water tank)
16
Shut-off valve
(field supply)
10
Booster heater
17
Non-return valve
(field supply)
11
Heat exchanger coil
FHL1...3
FHL3
Floor heating loop
(field supply)
Application Examples - Monobloc
DACA-EEDEN09-720
Application Examples - Monobloc
Field wiring configuration A
NOTE
L
H
■
Com
E(D/B)*/auto /Boiler
E(D/B)*
X2M
Boiler
thermostat input
1 2 3 4
X Y
A
K1A
K1A
K2A
K2A
Configuration B
Make sure that the bivalent hysteresis [C-04] has
sufficient differential to avoid frequent changeover
between the E(D/B)* unit and the boiler. As the
outdoor temperature is measured via the outdoor
unit, air thermistor make sure to install the
outdoor unit in the shade, so that it is not
influenced by the sun.
N
Boiler
thermostat input
Boiler thermostat input
A
Auxiliary contact (normal closed)
H
Heating demand room thermostat (optional)
K1A
Auxiliary relay for activation of E(D/B)* unit (field
supply)
K2A
Auxiliary relay for activation of boiler (field supply)
Frequent switching may cause corrosion of the
boiler in an early stage. Contact the manufacturer
of the boiler.
Field wiring configuration B
■
EKRP1HB
E(D/B)*
X2M
1 2 3 4
KCR
X1 X2
K1A
K1A
C Com H
EKRTW*
X Y
Boiler
thermostat input
Boiler
thermostat input
Boiler thermostat input
C
Cooling demand room thermostat (optional)
H
Heating demand room thermostat (optional)
Com
Common room thermostat (optional)
K1A
Auxiliary relay for activation of bolier unit
(field supply)
KCR
Permission signal for the auxiliary boiler
■
During heating operation of the E(D/B)* unit, the
unit will operate so as to achieve the target
leaving water temperature as set on the user
interface. When weather dependent operation is
active, the water temperature is determined
automatically depending on the outdoor
temperature.
During heating operation of the boiler, the boiler
will operate so as to achieve the target leaving
water temperature as set on the boiler controller.
Never set the target leaving water temperature set
point on the boiler controller above 131°F (55°C).
■
Make sure to only have 1 expansion vessel in the
water circuit. An expansion vessel is already
premounted in the Daikin unit.
Configuration A
Make sure to configure the DIP switch SS2-3 on the
PCB of the E(D/B)* switchbox correctly. Refer to
"Room thermostat installation configuration" on
page 23.
When the room thermostat requests heating, either the E(D/B)*
unit or the boiler starts operating, depending on the position of
the auxiliary contact (A).
For configuration B: Make sure to configure the field
settings [C-02, C-03 and C-04] correctly. Refer to
"Bivalent operation" on page 33.
Operation
■
Configuration A
Make sure that auxiliary contact (A) has sufficient
differential or time delay so as to avoid frequent
changeover between the E(D/B)* unit and the
boiler. If the auxiliary contact (A) is an outdoor
temperature thermostat, make sure to install the
thermostat in the shade, so that it is not
influenced or turned ON/OFF by the sun.
NOTE
Configuration B
When the room thermostat requests heating, either the E(D/B)*
unit or the boiler starts operating, depending on the outdoor
temperature (status of "permission signal for the auxiliary
boiler").
When the permission is given towards the boiler, the space
heating operation by the E(D/B)* unit will be automatically
switched off.
For more details see field setting [C-02~C-04].
CAUTION
Make sure that return water to the E(D/B)* heat exchanger
never exceeds 131°F (55°C).
For this reason, never put the target leaving water
temperature set point on the boiler controller above 131°F
(55°C) and install an aquastat(a) valve in the return water
flow of the E(D/B)* unit.
Make sure that the non-return valves (field supply) are
correctly installed in the system.
Make sure that the room thermostat (th) is not frequently
turned ON/OFF.
Daikin shall not be held liable for any damage resulting
from failure to observe this rule.
(a) The aquastat valve must be set for 131°F (55°C) and must operate to close the
return water flow to the unit when the measured temperature exceeds 131°F
(55°C). When the temperature drops to a lower level, the aquastat valve must
operate to open the return water flow to the E(D/B)* unit again.
Manual permission towards the E(D/B)* unit on the boiler.
In case only the E(D/B)* unit should operate in space
heating mode, disable the bivalent operation via setting
[C-02].
In case only the boiler should operate in space heating
mode, increase the bivalent ON temperature [C-03] to
77°F (25°C).
66
Application Examples - Monobloc
DACA-EEDEN09-720
Application Examples - Monobloc
When the room temperature of both zones is above the thermostat
set point, the outdoor unit and pump will stop operating.
Application 6
Space heating with room thermostat application through floor heating
loops and fan coil units. The floor heating loops and fan coil units
require different operating water temperatures.
NOTE
The floor heating loops require a lower water temperature in heating
mode compared to fan coil units. To achive these two set points, a
mixing station is used to adapt the water temperature according to
requirements of the floor heating loops. The fan coil units are directly
connected to the unit water circuit and the floor heating loops after
the mixing station. The control of this mixing station is not done by the
unit.
The operation and configuration of the field water circuit is the
responsibility of the installer.
NOTE
■
Make sure to connect the thermostat wires to the
correct terminals (see "Overview of the unit" on
page 11).
■
Make sure to configure the field settings [7-02],
[7-03] and [7-04] correctly. Refer to "Dual set point
control" on page 30.
■
Make sure to configure the DIP switch SS2-3 on
the PCB of the E(D/B) switch box correctly. Refer
to "Room thermostat installation configuration" on
page 23.
■
The request signals for space heating can be
implemented in two different ways (installer
choice).
- Thermo ON/OFF signal from room thermostat
- Status signal (active/not active) from the
mixing station
■
It is the installers responsibility to make sure no
unwanted situations can occur (e.g. too high
water temperatures towards floor heating loops,
etc.)
■
Daikin does not offer any type of mixing station.
Dual set point control only provides the possibility
to use two set points.
■
When only zone A request heating, zone B will be
fed with water at a temperature equal to the first
set point.
This can lead to unwanted heating of zone B.
■
When only zone B request heating, the mixing
station will be fed with water at a temperature
equal to the second set point.
Depending on the control of the mixing station,
the floor heating loop can still receive water at a
temperature equal to set point of the mixing
station.
Daikin only offers a dual set point control function. By this function
two set points can be generated. Depending on the required water
temperature (floor heating loops and/or fan coil units are required)
first set point or second set point can be activated.
T1
B
6
T2
FCU1
FCU2
1
2
3
FCU3
4
A
5
FHL1
7
FHL2
Be aware that the actual water temperature through the
floor heating loops depends on the control and setting of
the mixing station.
FHL3
1
Outdoor unit
2
Heat exchanger
3
Pump
4
Shut-off valve
5
Collector zone A
(field supply)
6
Collector zone B
(field supply)
7
Mixing station (field supply)
T1
Room thermostat for zone
A (optional)
T2
Room thermostat for zone
B (optional)
FCU1..3
Fan coil unit (optional)
FHL1...3
Floor heating loop
(field supply)
OVERVIEW OF THE UNIT
Opening the unit
The advantage of the dual set point control is that the heat
pump will/can operate at the lowest required leaving water
temperature when only floor heating is required. Higher
leaving water temperatures are only required in case fan
coil units are operating.
This results in a better performance of the heat pump.
1 2
3
Pump operation and space heating
When the room thermostat for the floor heating loop (T1) and the fan
coil units (T2) are connected to the indoor unit, the pump (4) will
operate when there is a request for heating from T1 and/or T2. The
outdoor unit will start operating to achieve the target leaving water
temperature. The target leaving water temperature depends on which
room thermostat is requesting heating.
67
Set point
Field setting
Thermo status
Zone A
First
UI
ON
OFF
ON
OFF
Zone B
Second
[7-03]
OFF
ON
ON
OFF
Resulting water temperature
UI
[7-03]
[7-03]
—
Result pump operation
ON
ON
ON
OFF
Door 1
gives access to the compressor compartment and electrical parts
Door 2
gives access to the electrical parts of the hydraulic compartment
Door 3
gives access to the hydraulic compartment
Switch off all power supply — i.e. unit power supply and
backup heater and domestic hot water tank power supply
(if applicable) — before removing doors 1 and 2.
Parts inside the unit can be hot.
Application Examples - Monobloc
DACA-EEDEN09-720
Installation - Monobloc
12. Installation - Monobloc
12.1 Installation Location
•
•
•
•
•
•
•
•
•
•
•
The equipment is not is not intended for use in a potentially explosive atmosphere.
Choose a place solid enough to bear the weight and vibration of the unit, where operation
sounds will not be amplified.
Choose a location where the hot/cold air discharged from the unit and the operation sounds
will not be bothersome to neighbors or users.
Avoid places such as bedrooms so that operation sounds are not a problem.
Allow sufficient space for carrying the unit into and out of the site.
Ensure there is sufficient space for air passage and a lack of obstructions around the air inlet
and the air outlet.
The site must be free from the possibility of flammable gas leakage in any nearby area.
Install units, power cable, and inter-unit cables at least 10 feet (3 m) away from televisions
and radios to prevent interference.
Depending on radio wave conditions, electromagnetic interference may still occur even if
installed more than 10 ft. (3 m) away.
In coastal areas or other places with salty atmosphere of sulfate gas, corrosion my shorten the
life of the outdoor unit.
Since condensate flows out of the outdoor unit, do not place anything under the unit that must
be kept from moisture.
IN COLD CLIMATES:
•
•
•
•
•
68
To prevent exposure to wind, install the outdoor unit with its suction side facing the wall.
Never install the outdoor unit at a site where the suction side may be exposed directly to wind.
To prevent exposure to wind, install a baffle plate on the air discharge side of the outdoor unit.
Unit should be installed with a minimum of 4” (10 cm) free space below the unit’s bottom plate
at all condition, e.g., heavy snowfall (construct a pedestal if necessary).
In heavy snowfall areas, it is very important to select an installation site where the snow will
not affect the unit. If lateral snowfall is possible, make sure the heat exchanger coil is not
affected by the snow (construct a lateral canopy if necessary). See Figure 1:
Installation - Monobloc
DACA-EEDEN09-720
Installation - Monobloc
12.2 Installation Space
69
Installation - Monobloc
DACA-EEDEN09-720
Hydronic Performance - Monobloc
13. Hydronic Performance - Monobloc
70
Hydronic Performance - Monobloc
DACA-EEDEN09-720
Operation Range - Monobloc
14. Operation Range - Monobloc
71
Operation Range - Monobloc
DACA-EEDEN09-720
Domestic Hot Water Tank
1. Domestic Hot Water Tank
1.1
Features
•
Stainless steel domestic hot water tank & heat exchanger
•
Integrated 3kW electric booster heater
•
Two sizes (50 gal & 80 gal)
•
3-way valve included
Domestic Hot Water (DHW) Tank
The EKHWS domestic hot water tank with integrated 3 kW electric booster heater can be connected to both the split
system hydrobox or monobloc. The domestic hot water tank is available in two sizes: 50 gallon (200 liter) or 80 gallon
(300 liter). These domestic hot water tanks are for floor-standing indoor installations.
72
Domestic Hot Water Tank
DACA-EEDEN09-720
Specifications - DHW
2. Specifications - DHW
2-1
TECHNICAL SPECIFICATIONS
Casing
EKHWS050BA3VJU
Color
Material
Dimensions
Packing
Packing
Epoxy-coated mild steel
Height
in (mm)
Width
in (mm)
23-5/8 (600)
23-5/8 (600)
Depth
in (mm)
23-5/8 (600)
23-5/8 (600)
Height
in (mm)
45-3/8 (1,150)
63 (1,600)
Width
in (mm)
22-7/8 (580)
22-7/8 (580)
Depth
in (mm)
22-7/8 (580)
22-7/8 (580)
Unit
lb (kg)
99.2 (45)
130 (59)
Packed Unit
lb (kg)
112.4 (51)
Unit
Weight
EKHWS080BA3VJU
Neutral white
47-1/4 (1,200)
Material
65 (1,650)
145.5 (66)
EPS
Carton
Weight
Main
components
Tank
Tank
Water volume
8.81 (4 )
11 (5)
gal (l)
50 (200)
80 (300)
Material
Insulation
Heat
exchanger
Stainless steel 316LSS
Max.
temperature
°F (°C)
185 (85)
185 (85)
Max. water
pressure
PSI (bar)
145 (10 )
145 (10)
Material
Min. thickness
Main
components
lb (kg)
Polyurethane foam
in (mm)
1-5/8 (40)
Quantity
Material
Capacity
Temperature
sensor
Piping
connections
2-2
Unit
1
10,255 (3)
10,255 (3)
44 (10)
44 (10)
Rp1
inch
Cable length
ft (m)
2xRp1
39.4 (12)
39.4 (12)
Water inlet H/E Diameter
inch (BSPP)
Water outlet H/E Diameter
inch (BSPP)
G 3/4 (female)
Cold water in Diameter
inch (BSPP)
G 3/4 (female)
G 3/4 (female)
Hot water out Diameter
inch (BSPP)
G 3/4 (female)
Recirculation connection
inch (BSPP)
G 3/4 (female)
ELECTRICAL SPECIFICATIONS
Power Supply
Current
73
1
BTU/hr (kW)
Coefficient of
flow at 14.5 PSI gpm (m3/h)
(1 bar)
Inlet
inch
Outlet
1
Stainless steel 316LSS
Booster heater Quantity
3-Way Valve
1-5/8 (40)
1
EKHWS050BA3VJU
Phase
EKHWS080BA3VJU
1~
1~
Frequency
Hz
60
60
Voltage
V
208/230
208/230
Minimum Circuit Amps (MCA)
A
14.3
14.3
Maximum Overcurrent Protection (MOP)
A
20
20
Specifications - DHW
DACA-EEDEN09-720
Domestic Hot Water Basic Performance Overview
3. Domestic Hot Water Basic Performance Overview
The Daikin Altherma heat pump in combination with the optional domestic hot water tank provides hot water for
household usage (Altherma TW DHW).
The following data provides information to select the proper sized domestic hot water tank to ensure maximum comfort
and efficiency.
(1) Domestic hot water volume:
The volume of hot water available for domestic usage depends on the physical volume of the tank, the domestic hot
water setpoint temperature, and the temperature spreading in the tank. Therefore the equivalent hot water volume is
termed EHWV.
Definition EHWV = The volume of hot water available for domestic usage at a temperature of 104° (40°C), which is
considered a comfortable domestic hot water temperature.
Tank
50 gal
(200 l)
80 gal
(300 l)
Grade:
Usage Pattern:
Setpoint temp °F (°C)
131 (55)
149 (65)
167 (75)
131 (55)
149 (65)
167 (75)
EHWV gal (l)
42 (160)
53 (200)
63 (240)
78 (205)
102 (385)
102 (435)
Usage Pattern
Medium

+
++
++
++
Modest
+
++
++
++
++
High




+
++ excessive availability of domestic hot water
+ sufficient availability of domestic hot water
temporary shortage of domestic hot water can occur
Modest: Daily demand up to 58 gal (220 l) = typical 2-person usage pattern
Medium: Daily demand up to 85 gal (325 l) = typcial 3 - 4 person usage pattern
High:
Daily demand up to 145 gal (550 l) = typical 4 - 6 person usage pattern
(2) Heat up time:
Definition of Heat-Up Time: The time required to reheat the domestic hot water tank to 131 F (55 C) after tapping a
certain volume of hot water. NOTE: Changing the field settings (see installation manual) can influence the heat-up
time.
Tank
50 gal (200 l)
Setpoint °F (°C)
131 (55)
Heat up time for 39 gal (150 l) bath (min)
60
Heat up time for 13 gal (50 l) bath (min)
40
80 gal (300 l)
131 (55)
50
30
Conditions for testing: Ta =44.6°CDB / 42.8°FWB, Troom =68°F, Tstart = 50°F, outdoor unit type: ERLQ054*VJU
Conditions for testing: Ta = 7°CDB / 6 °CWB, Troom = 20°C, Tstart = 10°C, outdoor unit type: ERLQ054*VJU
(3) Efficiency of domestic hot water production:
In the Daikin Altherma system, both the heat pump and the electric booster heater supply the energy to produce
domestic hot water. The higher the portion of energy supplied by the heat pump, the more energy efficient the system
is. Lowering the setpoint temperature increases the portion of energy supplied by the heat pump and thus the
efficiency of the system. The percentage of energy supplied by the heat pump in relation to total energy need for
domestic hot water is displayed in the following graph:
Conditions:
Simulation of daily real-life conditions based upon medium
usage.
Outdoor temp: 44.6°FDB /42.8° FWB (7°CDB/ 6°CWB)
Room temp: 68 F (20 C)
Tank Type: 50 gal (200 l)
Field Settings: Default field settings (see Installation Manual)
74
Domestic Hot Water Basic Performance Overview
DACA-EEDEN09-720
Dimensional Drawing & Center of Gravity - DHW
4. Dimensional Drawing & Center of Gravity - DHW
75
Dimensional Drawing & Center of Gravity - DHW
DACA-EEDEN09-720
4.1
76
Dimensional Drawing & Center of Gravity - DHW
Domestic Hot Water Tank Summary
Dimensional Drawing & Center of Gravity - DHW
DACA-EEDEN09-720
Three-Way Valve Summary
5. Three-Way Valve Summary
77
Three-Way Valve Summary
DACA-EEDEN09-720
Three-Way Valve Summary
78
Three-Way Valve Summary
DACA-EEDEN09-720
Solar Kit (EKSOLHWBAVJU) - Features
Options
1. Solar Kit (EKSOLHWBAVJU) - Features
t 1 i V aKA m W r H r e L a hO l tS olK S•EA
Connectable to solar collectors
•
Easy connection to EKHWS* DHW tanks
•
Enables DHW heating by means of the sun
The solar kit is to be connected to the Daikin domestic hot water tank. The solar kit will enables domestic hot water to
be heated by the sun when it is available. The solar kit intergrates the field-supplied solar thermal panels with the pump
station and the Daikin domestic hot water tank.
79
Solar Kit (EKSOLHWBAVJU) - Features
DACA-EEDEN09-720
Specifications  Solar Kit
1.1
2-1
Solar Kit (EKSOLHWBAVJU) - Features
TECHNICAL SPECIFICATIONS
Dimensions
Packing
Unit
Weight
Packing
in (mm)
Width
in (mm)
13-1/2 (340)
Depth
in (mm)
11-5/8 (295)
Pump
31-3/8 (795)
30-3/8 (770)
Height
in (mm)
Width
in (mm)
12-1/8 (305)
Depth
in (mm)
10-3/4 (270)
Unit
lb (kg)
17.6 (8)
Packed Unit
lb (kg)
19.8 (9)
Material
Carton
Weight
Heat
Exchanger
EKSOLHWBAVJU
Height
lb (kg)
Type
1
Brazed plate
Pressure drop
Solar side PSI
(kPa)
Maximum inlet
temperature
Solar side °F (°C)
Capacity
W/K
Logarithmic mean
temperature difference
(LMTD)
K
3.12 (21.5)
230°F (110°C)
1,400
5
Type
water cooled
Number of speeds
3
Power input
W
46
Sound
Sound Pressure
dBA
27
Water circuit
Piping connections
diameter
inch
FBSP
3/4
Maximum
°F (°C)
95 (35)
Minimum
°F (°C)
1
Insulation material
Ambient
temperature
2-2
EPP
ELECTRICAL SPECIFICATIONS
Unit
Power Supply
Phase
1~
Frequency Hz
Voltage
Voltage range
V
60
208/230
Minimum
-10%
Maximum
+10%
Power Supply Intake
80
EKSOLHWBAVJU
indoor unit
Solar Kit (EKSOLHWBAVJU) - Features
DACA-EEDEN09-720
1.2
81
Solar Kit (EKSOLHWBAVJU) - Features
Dimensional Drwg. & Center of Gravity - Solar Kit
Solar Kit (EKSOLHWBAVJU) - Features
DACA-EEDEN09-720
1.3
82
Solar Kit (EKSOLHWBAVJU) - Features
Piping Diagram - Solar Kit
Solar Kit (EKSOLHWBAVJU) - Features
DACA-EEDEN09-720
1.4
83
Solar Kit (EKSOLHWBAVJU) - Features
Wiring Diagram - Solar Kit
Solar Kit (EKSOLHWBAVJU) - Features
DACA-EEDEN09-720
Room Thermostat  EKRTWA
2. Room Thermostat  EKRTWA
t 1 i V aKA m W r H r e L a hO l tS olK SEA
84
Room Thermostat  EKRTWA
Room Thermostat  EKRTWA
DACA-EEDEN09-720
2.1
4-1
Specifications - Room Thermostat
TECHNICAL SPECIFICATIONS
Dimensions
Unit
Packing
Weight
Unit
Packing
Ambient
temperature
Temperature
setting range
Height
in (mm)
EKRTW
3-1/2 (87)
Width
in (mm)
5 (125)
Depth
in (mm)
1-3/8 (34)
Height
in (mm)
2-5/8 (65)
Width
in (mm)
7 (175)
Depth
in (mm)
4 (100)
Net
oz (g)
7.6 (215)
Gross
oz (g)
15.5 oz (440 g)
Material
Carton
Weight
oz (g)
2 (55)
Storage
°F (°C)
-4~140 (-20~60)
Operation
°F (°C)
32~122 (0~50)
Heating
°F (°C)
39.298.6 (437)
Cooling
°F (°C)
39.298.6 (437)
°F (°C)
32.9 (0.5)
Temperature setting resolution
Clock
Yes
Regulation function
Features
Item
Proportional band
Heating only
Heating and cooling
Comfort function mode (= comfort setpoint)
Reduced function mode (=night setback setpoint)
Scheduled function mode(= schedule timer)
Number of setpoint changes
Note
12/day
Item
Holiday function mode
Off function (with integrated frost protection)
Setpoint limitation
Keylock function
4-2
ELECTRICAL SPECIFICATIONS
Power Supply
Connection
Output relays
85
Voltage
EKRTW
battery powered 3* AA-LR6 (alkaline)
Wired
Maximum load 1A - 24 VAC
Room Thermostat  EKRTWA
Room Thermostat  EKRTWA
DACA-EEDEN09-720
2.2
Dimensions - Room Thermostat
3-1/2” (87 mm)
2-1/3” (60 mm)
1-1/3” (34 mm)
86
5” (125 mm)
Room Thermostat  EKRTWA
Room Thermostat  EKRTWA
DACA-EEDEN09-720
Application Example - Room Thermostat
5 ft. / 1.5 m
2.3
8”
87
/
0.2
m
Room Thermostat  EKRTWA
DACA-EEDEN09-720
2.4
88
Room Thermostat  EKRTWA
Wiring Connection - Room Thermostat
Room Thermostat  EKRTWA
DACA-EEDEN09-720
2.5
89
Room Thermostat  EKRTWA
User Display - Room Thermostat
Room Thermostat  EKRTWA
DACA-EEDEN09-720
2.6
Room Thermostat  EKRTWA
Functional Summary - Room Thermostat
•
Room temperature control, base on the measurements of the internal sensor.
•
Cooling and heating mode, with possibility to disable cooling function if not required.
•
Automatic daylight-saving time change.
•
Battery driven so no external power required.
The thermostats are preprogrammed with a set of 5 modes:
In the Comfort mode, the temperature is kept fixed at an adjustable set value. Default values are 70F (21C) in
heating mode and 75F (24C) in cooling mode.
In the Reduced mode, the temperature is kept fixed at an adjustable set value. Default values are 62.5F (17C) in
heating mode and 82.5F (28C) in cooling mode.
In the Off mode, the thermostat is still active as a frost protection which keeps the temperature above 39F (4C).
In the Holiday mode, the temperature is kept fixed at an adjustable set value. Default values are 57F (14C) in heating
mode and 86F (30C) in cooling mode for a programmed duration.
In the Schedule mode, the temperature is adjusted in accordance with a pre-planned schedule of either of the
preprogrammed standard schedules, or one of the 2 schedules the user can program on his own. ONe can also
choose whether the programmed times are when the heat pump starts adjusting temperatures or at what time the
temperatures are to be reached.
90
Room Thermostat  EKRTWA
DACA-EEDEN09-720
Condensate Kit  EKHBDP
3. Condensate Kit  EKHBDP
NOTE: Condensate Kit must be used with EKHBX054* Heat Pump Hydrobox
91
Condensate Kit  EKHBDP
DACA-EEDEN09-720
Digital I/O PCB Kit  EKRP1HBAAU
4. Digital I/O PCB Kit  EKRP1HBAAU
t 1 i V aKA m W r H r e L a hO l tS olK S•EA
An optional EKRP1HB digital I/O PCB can be connected to the indoor hydrobox or the outdoor monobloc unit
and allows:
•
Remote Alarm Output
•
Bivalent operation (permission signal for the auxiliary boiler)
•
Solar DHW priority mode
•
Refer to the operation manual of the indoor unit and to the installation manual of the digital I/O PCB for more
information.
•
Refer to the wiring diagram or connection diagram for connecting this PCB to the unit
92
Digital I/O PCB Kit  EKRP1HBAAU
DACA-EEDEN09-720
Appendix - Field Settings
1. Field Settings Overview
93
DACA-EEDEN09-720
NOTE
[1] Weather dependent set point (heating operation only)
■
Before shipping, the set values have been set as
shown under "Field settings table" on page 35.
■
When exiting FIELD SET MODE, "88" may be
displayed on the user interface LCD while the unit
initialises itself.
Detailed description
[0] User permission level
If required, certain user interface buttons can be made unavailable for
the user.
Three permission levels are defined (see the table below). Switching
between level 1 and level 2/3 is done by simultaneously pressing
buttons pfi and pfj immediately followed by
simultaneously pressing buttons s and ba, and keeping all 4
buttons pressed for at least 5 seconds (in normal mode). Note that no
indication on the user interface is given. When level 2/3 is selected,
the actual permission level — either level 2 or level 3 — is
determined by the field setting [0-00].
Permission level
Button
■ [1-00] Low ambient temperature (Lo_A): low outdoor
temperature.
■ [1-01] High ambient temperature (Hi_A): high outdoor
temperature.
■ [1-02] Set point at low ambient temperature (Lo_Ti): the
target outgoing water temperature when the outdoor
temperature equals or drops below the low ambient
temperature (Lo_A).
Note that the Lo_Ti value should be higher than Hi_Ti, as for
colder outdoor temperatures (i.e. Lo_A) warmer water is
required.
2
3
Quiet mode button
s
operable
—
—
Weather dependent
set point button
ba
operable
—
—
Schedule timer
enable/disable button
pr
operable
operable
—
Programming button
<
operable
—
—
Time adjust buttons
pf
i
pf
j
operable
—
—
Tt
z
operable
—
—
Lo_Ti
Inspection/test
operation button
1
The weather dependent set point field settings define the parameters
for the weather dependent operation of the unit. When weather
dependent operation is active the water temperature is determined
automatically depending on the outdoor temperature: colder outdoor
temperatures will result in warmer water and vice versa. During
weather dependent operation, the user has the possibility to shift up
or down the target water temperature by a maximum of 41°F (5°C).
See the operation manual for more details on weather dependent
operation.
■ [1-03] Set point at high ambient temperature (Hi_Ti): the
target outgoing water temperature when the outdoor
temperature equals or rises above the high ambient
temperature (Hi_A).
Note that the Hi_Ti value should be lower than Lo_Ti, as for
warmer outdoor temperatures (i.e. Hi_A) less warm water
suffices.
+ 05
00
Hi_Ti
– 05
Lo_A
Target water temperature
TA
Ambient (outdoor) temperature
= Shift value
94
Hi_A
Tt
TA
Shift value
DACA-EEDEN09-720
[2] Disinfection function
[4] Backup heater operation and space heating off temperature
Applies only to installations with a domestic hot water tank.
Backup heater operation
The disinfection function disinfects the domestic hot water tank by
periodically heating the domestic water to a specific temperature.
The operation of the backup heater can be enabled or disabled, or it
can be disabled depending on operation of the booster heater.
■ [4-00] Status: defines whether backup heater operation is
enabled (1) or disabled (0).
CAUTION
The disinfection function field settings must be configured
by the installer according to local laws and regulations.
NOTE
■ [2-00] Operation interval: day(s) of the week at which the
domestic water should be heated.
■ [2-01] Status: defines whether the disinfection function is
turned on (1) or off (0).
■ [2-02] Start time: time of the day at which the domestic water
should be heated.
■ [2-03] Set point: high water temperature to be reached.
■ [2-04] Interval: time period defining how long the set point
temperature should be maintained.
TDHW
[2-03]
[2-04]
TH
TU
00.00
01.00
22.00
23.00
24.00
t
[2-02]
TDHW
Domestic hot water temperature
TU
User set point temperature (as set on the user interface)
TH
High set point temperature [2-03]
t
Time
WARNING
Be aware that the domestic hot water temperature at the
hot water tap will be equal to the value selected in field
setting [2-03] after a disinfection operation.
If this high domestic hot water temperature can be a
potential risk for human injuries, a mixing valve (field
supply) shall be installed at the hot water outlet connection
of the domestic hot water tank. This mixing valve shall
secure that the hot water temperature at the hot water tap
never rise above a set maximum value. This maximum
allowable hot water temperature shall be selected
according to local laws and regulations.
[3] Auto restart
When power returns after a power supply failure, the auto restart
function reapplies the user interface settings at the time of the power
supply failure.
NOTE
It is therefore recommended to leave the auto restart
function enabled.
Note that with the function disabled the schedule timer will not be
activated when power returns to the unit after a power supply failure.
Press the pr button to enable the schedule timer again.
■ [3-00] Status: defines whether the auto restart function is
turned ON (0) or OFF (1).
NOTE
95
If the benefit kWh rate power supply is of the type that
power supply is interrupted, then always allow the auto
restart function.
Even in case the backup heater operation
status field setting [4-00] is set to disabled (0),
the backup heater can operate during start-up
and defrost operation.
■ [4-01] Priority: defines whether backup heater and booster
heater can operate simultaneously (0), or if the booster
heater operation has priority over the backup heater
operation (1), or if the backup heater operation has priority
over the booster heater operation (2).
NOTE
When the priority field setting is set to ON (1),
space heating performance of the system
might be decreased at low outdoor
temperatures, since in case of domestic water
heating demand the backup heater will not be
available for space heating (space heating will
still be provided by the heat pump).
When the priority field setting is set to ON (2),
domestic water heating performance of the
system might be decreased at low outdoor
temperatures, since in case of space heating
demand the booster heater will not be
available for domestic water heating. However
domestic water heating by heat pump will still
be available.
When the priority field setting is set to OFF (0),
make sure that electrical power consumption
does not exceed supply limits.
Space heating off temperature
■ [4-02] Space heating off temperature: outdoor temperature
above which space heating is turned off, to avoid
overheating.
■ [4-03] Booster heater operation: defines whether the optional
booster heater operation is enabled (1) or has certain
limitations (0/2/3).
Explanation of settings of [4-03]
Booster heater will/can only operate if domestic hot water mode
is activated (w).
■ [4-03]=0, then booster heater operation is only allowed
during "[2] Disinfection function" and "Powerful domestic
water heating" (see operation manual).
This setting is only recommended in case the capacity of the
heat pump can cover the heating requirements of the house
and domestic hot water over the complete heating season.
The result of this setting is that the domestic hot water will
never be heated by the booster heater except for
"[2] Disinfection function" and "Powerful domestic water
heating" (see operation manual).
If the booster heater operation is limited ([4-03]=0)
and the ambient outdoor temperature TA is lower than
the field setting to which parameter [5-03] is set and
[5-02]=1, then the domestic hot water will not be
heated.
The consequence of this setting is that the domestic
hot water temperature (TDHW) can be maximum the
heat pump OFF temperature (THP OFF). Refer to
setting of [6-00] and [6-01] in "[6]" on page 29.
■ [4-03]=1, then booster heater heater operation is only
determined by booster heater OFF temperature (T BH OFF),
booster heater ON temperature (TBH ON) and/or schedule
timer. Refer to setting "[7-00]" on page 30 and "[7-01]" on
page 30.
■ [4-03]=2, then booster heater operation is only allowed if heat
pump is out of "operation range" of heat pump domestic
water heating mode (TA<[5-03] or TA>95°F(35°C)) or
domestic hot water temperature is 3.6°F (2°C) lower then the
heat pump OFF temperature (THP OFF) for domestic hot
water mode (TDHW>THP OFF–3.6°F(2°C)). (Refer to setting
[5-03] on page 28, [6-00] on page 29 and [6-01] on page 29).
Results in the most optimum coverage of domestic hot water
heated by the pump.
■ [4-03]=3, then booster heater operation is the same as
setting 1, except that booster heater is OFF when the heat
pump is active in domestic hot water mode. The
consequence of this functionality is that setting [8-03] is not
relevant.
Results in optimum coverage of domestic hot water heated
by heat pump in relation with [8-04].
96
■
When setting [4-03]=1/2/3, the booster heater
operation can still be restricted by the schedule
timer as well. I.e., when booster heater operation
is preferred during certain period of the day. (See
operation manual)
■
When setting [4-03]=2, the booster heater will be
allowed to operate when TA<[5-03] independent
of the status of [5-02]. If bivalent operation is
enabled and permission signal for auxiliary boiler
is ON, the booster heater will be restricted even
when TA<[5-03]. (See "[C-02]" on page 33).
■
Booster heater is always allowed during powerful
and disinfection function, except for the period
that the backup heater operation is required for
safety reasons and [4-02]=1.
O
C
O
BL
The operation of the booster heater can be enabled or limited
depending on outdoor temperature (TA), domestic hot water
temperature (TDHW) or operation mode of the heat pump.
■ [4-04] Freeze protection function: avoids freezing of the
water piping between home and unit. In case of low ambient
temperatures it will activate the pump and in case of low
water temperatures it will additionally activate the backup
heater. Monobloc only.
Default freeze protection function takes into account freezing
of water piping which is insufficiently insulated.
Basically it means that the pump is activated whenever
ambient temperatures become close to freezing,
independently of the working temperature.
N
O
Applies only to installations with a domestic hot water tank.
M
O
Booster heater operation
N
LY
DACA-EEDEN09-720
[5] Equilibrium
temperature
temperature
and
space
heating
priority
Equilibrium temperature — The 'equilibrium temperature' field
settings apply to operation of the backup heater.
When the equilibrium temperature function is enabled, operation of
the backup heater is restricted to low outdoor temperatures, i.e. when
the outdoor temperature equals or drops below the specified
equilibrium temperature. When the function is disabled, operation of
the backup heater is possible at all outdoor temperatures. Enabling
this function reduces the working time of the backup heater.
■ [5-00] Equilibrium temperature status: specifies whether the
equilibrium temperature function is enabled (1) or
disabled (0).
■ [5-01] Equilibrium temperature: outdoor temperature below
which operation of the backup heater is allowed.
Space heating priority temperature — Applies only to installations
with a domestic hot water tank. — The 'space heating priority
temperature' field settings apply to operation of the 3-way valve and
the booster heater in the domestic hot water tank.
When the space heating priority function is enabled, it is assured that
the full capacity of the heat pump is used for space heating only
when the outdoor temperature equals or drops below the specified
space heating priority temperature, i.e. low outdoor temperature. In
this case the domestic hot water will only be heated by the booster
heater.
■ [5-02] Space heating priority status: specifies whether space
heating priority is enabled (1) or disabled (0).
■ [5-03] Space heating priority temperature: outdoor
temperature below which the domestic hot water will be
heated by the booster heater only, i.e. low outdoor
temperature.
If the booster heater operation is limited ([4-03]=0)
and the ambient outdoor temperature TA is lower than
the field setting to which parameter [5-03] is set and
[5-02]=1, then the domestic hot water will not be
heated.
DACA-EEDEN09-720
■ [5-04] Set point correction for domestic hot water
temperature: set point correction for the desired domestic hot
water temperature, to be applied at low outdoor temperature
when space heating priority is enabled. The corrected
(higher) set point will make sure that the total heat capacity of
the water in the tank remains approximately unchanged, by
compensating for the colder bottom water layer of the tank
(because the heat exchanger coil is not operational) with a
warmer top layer.
Tset
[6] DT for heat pump domestic water heating mode
Applies only to installations with a domestic hot water tank.
The 'DT (temperature difference) for heat pump domestic water
heating mode' field settings determine the temperatures at which
heating of the domestic hot water by the heat pump will be started
(i.e., the heat pump ON temperature) and stopped (i.e., the heat
pump OFF temperature).
When the domestic hot water temperature drops below the heat
pump ON temperature (THP ON), heating of the domestic hot water by
the heat pump will be started. As soon as the domestic hot water
temperature reaches the heat pump OFF temperature ( THP OFF) or
the user set point temperature (TU), heating of the domestic hot water
by the heat pump will be stopped (by switching the 3-way valve).
The heat pump OFF temperature, and the heat pump ON
temperature, and its relation with field settings [6-00] and [6-01] are
explained in the illustration below.
[5-04]
TU
■ [6-00] Start: temperature difference determining the heat
pump ON temperature (THP ON). See illustration.
[5-03]
Tset
Domestic hot water set point temperature
TU
User set point (as set on the user interface)
TA
Ambient (outdoor) temperature
TA
■ [6-01] Stop: temperature difference determining the heat
pump OFF temperature (THP OFF). See illustration.
TU > THP MAX
T(°C) T(°F)
Space heating priority
70
158
TU
TU
= 158°F (70°C)
[6-01] = 3.6°F (2°C)
[6-00] = 12.6°F (7°C)
WARNING
Be aware that the domestic hot water temperature will be
automatically increased with the value selected in field
setting [5-04] (if the outdoor temperature drops below field
setting [5-03]) compare to the user set point for domestic
hot water (TU). Refer to field setting [5-03], [7-00] and the
operation manual to select preferable set point.
If this high domestic hot water temperature can be a
potential risk for human injuries, a mixing valve (field
supply) shall be installed at the hot water outlet connection
of the domestic hot water tank. This mixing valve shall
secure that the hot water temperature at the hot water tap
never rise above a set maximum value. This maximum
allowable hot water temperature shall be selected
according to local laws and regulations.
50
122
48 118.4
THP MAX
THP OFF
41 105.8
THP ON
[6-01]
[6-00]
TU < THP MAX
TU
= 113°F (45°C)
[6-01] = 3.6°F (2°C)
[6-00] = 12.6°F (7°C)
T(°C) T(°F)
50
122
45
113
THP MAX
TU = THP OFF
[6-00]
38 100.4
TU
THP ON
User set point temperature (as set on the user interface)
THP MAX
Maximum heat pump temperature at sensor in domestic hot
water tank (122°F)(50°C)(depending on TA)(a)
THP OFF
Heat pump OFF temperature
THP ON
Heat pump ON temperature
(a) 122°F (50°C) = THP MAX at TA≤77°F (25°C).
118.4°F (48°C) = THP MAX at TA>77°F (25°C).
The maximum domestic hot water temperature that can be
reached with the heat pump is 122°F (50°C). It is advised
to select THP OFF not higher than 118.4°F (48°C) in order
to improve performance of the heat pump during domestic
water heating mode.
When setting [4-03]=0 or 2 special attention to setting
[6-00] is recommended. A good balance between the
required domestic hot water temperature and heat pump
ON temperature (THP ON) is a must.
97
DACA-EEDEN09-720
[7] DT for booster heater and dual set point control
WARNING
DT for booster heater
Be aware that the domestic hot water temperature will be
automatically increased (always) with the value selected in
field setting [7-00] compare to the user set point for
domestic hot water (TU). Refer to field setting [7-00] and
the operation manual to select preferable set point.
Applies only to installations with a domestic hot water tank.
When the domestic hot water is heated and the domestic hot water
set point temperature (as set by the user) has been reached, the
booster heater will continue to heat the domestic hot water to a
temperature a few degrees above the set point temperature, i.e. the
booster heater OFF temperature. These extra degrees are specified
by the domestic hot water step length field setting. Correct setting
prevents the booster heater from repeatedly turning on and off (i.e.
chattering) to maintain the domestic hot water set point temperature.
Note: the booster heater will turn back on when the domestic hot
water temperature drops [7-01] (field setting) below the booster
heater OFF temperature.
If this high water temperature can be a potential risk for
human injuries, a mixing valve (field supply) shall be
installed at the hot water outlet connection of the domestic
hot water tank. This mixing valve shall secure that the hot
water temperature at the hot water tap never rise above a
set maximum value. This maximum allowable hot water
temperature shall be selected according to local laws and
regulations.
If the schedule timer for booster heater (see the operation
manual) is active, the booster heater will only operate if
allowed by this schedule timer.
■ [7-00] Domestic hot water step length: temperature
difference above the domestic hot water set point temperature before
the booster heater is turned off.
TDHW (°F)
■ [7-01] Hysteresis value booster heater: temperature
difference determining the booster heater ON temperature
(TBH ON). TBH ON = TBH OFF – [7-01]
The minimum value for booster heater ON
temperature (TBH ON) is 3.6°F (2°C) (fixed) below heat
pump OFF temperature (THP OFF).
[7-01]
[7-00]
TBH OFF 163.4
TBH ON 159.8
TU 158
If the booster heater operation is limited ([4-03]=0), then
set point of field setting parameter [7-00] has only meaning
for powerful domestic water heating.
140
THP MAX 122
THP OFF 118.4
Dual set point control
[6-01]
[6-00]
THP ON 105.8
104
Applies only to installations with different heat emitter which require
different set points.
Dual set point control makes it possible to generate 2 different set
points.
86
68
HP
BH
50
TU
[7-00]
[6-01]
[6-00]
= 158°F
= 5.4°F
= 3.6°F
= 12.6°F
NOTE
HP
41
t
[7-00]
TBH OFF 73
TBH ON 71
TU 70
■ [7-04] Second set point cooling: specifies the second set
point temperature in cooling operation.
[7-01]
60
THP MAX 50
THP OFF 48
[6-01]
[6-00]
THP ON 41
40
30
20
HP
BH
10
TU
[7-00]
[6-01]
[6-00]
= 70°C
= 3°C
= 2°C
= 7°C
HP
5
t
BH
Booster heater
HP
Heat pump. If heating up time by the heat pump takes too
long, auxiliary heating by the booster heater can take place
TBH OFF
Booster heater OFF temperature (TU + [7-00])
TBH ON
Booster heater ON temperature
((TBH OFF – 4°F) (TBH OFF – 2°C))
THP MAX
Maximum heat pump temperature at sensor in domestic hot
water tank
THP OFF
Heat pump OFF temperature (THP MAX – [6-01])
THP ON
Heat pump ON temperature (THP OFF – [6-00])
TU
t
98
■ [7-02] Dual set point control status: defines whether the dual
set point control is enabled (1) or disabled (0).
■ [7-03] Second set point heating: specifies the second set
point temperature in heating operation.
TDHW (°C)
TDHW
There is no indication available which set point is
active!
Domestic hot water temperature
User set point temperature (as set on the user interface)
Time
DACA-EEDEN09-720
NOTE
■
[8] Domestic water heating mode timer
The first set point heating/cooling is the set point
selected on the user interface.
- In heating mode the first set point can be a
fixed value or weather dependent.
- In cooling mode the first set point is always a
fixed value.
■
The second set point heating [7-03] should be
linked to the heat emitters which requires the
highest set point in heating mode. Example: fan
coil unit.
■
The second set point cooling [7-04] should be
linked to the heat emitters which requires the
lowest set point in cooling mode. Example: fain
coil unit.
■
■
The actual second set point heating value
depends on the selected value of setting [7-03].
- In case [7-03]=1.8~43.2°F (1~24°C), the
actual second set point will be first set point
heating increased with [7-03] (the maximum is
131°F (55°C)).
In this way the second set point heating is
linked to the first set point heating.
- In case [7-03]=77~131°F (25~55°C), the
actual second set point heating is equal to
[7-03].
The 'domestic water heating mode timer' field settings defines the
minimum and maximum domestic water heating times, minimum time
between two domestic water heating cycles by heat pump, and
booster heater delay time.
■ [8-00] Minimum running time: specifies the minimum time
period during which heat pump domestic water heating mode
should be activated, even when the target domestic hot water
temperature for heat pump (THP OFF) has already been
reached.
■ [8-01] Maximum running time: specifies the maximum time
period during which heat pump domestic water heating mode
can be activated, even when the target domestic hot water
temperature for heat pump (THP OFF) has not yet been
reached.
The actual maximum running time will automatically variate
between [8-01] and [8-01]+[8-04] depending on the outdoor
temperature. See figure in chapter "[8-04]" on page 32.
Note that when the unit is configured to work with a
room thermostat (refer to "Room thermostat
installation configuration" on page 23), the
maximum running timer will only be taken into
account when there is a request for space cooling
or space heating. When there is no request for
room cooling or room heating, domestic water
heating by the heat pump will continue until the
'heat pump OFF temperature' (see field settings [6]
on page 29) is reached. When no room thermostat
is installed, the timer is always taken into account.
The selection of second set point or first set point
is determined by the terminals (X2M: 1, 2, 4).
The second set point has always priority on the
first set point.
X2M
1 2 3 4
SP2
SP1
SP1
First set point contact
SP2
Second set point
contact
When dual set point control is enabled, heating/cooling
selection always has to be done on the user interface.
NOTE
Applies only to installations with a domestic hot water tank.
■ [8-02] Anti-recycling time: specifies the minimum required
interval between two heat pump domestic water heating
mode cycles.
The actual anti-recycling time will automatically variate
between [8-02] and 0 depending on the outdoor temperature.
See figure in chapter "[8-04]" on page 32.
It is the responsibility of the installer to make sure no
unwanted situations can occur.
1
0
It is very important that the water temperature to the
floor heating loops never becomes too high in heating
mode or never too cold in cooling mode. Failure to
observe this rule can result in construction damage or
discomfort. For example in cooling mode condensation
on the floor can occur when water towards the floor
heating loops is too cold (dew point).
1
0
[8-00]
[8-01]
[8-02]
t
1
Domestic water heating (1 = active, 0 = not active)
2
Hot water request (1 = request, 0 = no request)
t
Time
If the outdoor temperature is higher than the field setting to
which parameter [4-02] is set, then field settings of
parameters [8-01], [8-02], and [8-04] are not considered.
99
DACA-EEDEN09-720
■ [8-03] Booster heater delay time: specifies the start-up time
delay of the booster heater operation when heat pump
domestic water heating mode is active.
■
When heat pump is active in domestic water
heating mode, the delay time of booster
heater is [8-03].
■
When heat pump is not active in domestic
water heating mode, the delay time is 20 min.
■
The delay timer starts from booster heater ON
temperature (TBH ON)
■ [8-04] Additional running time at [4-02]/[F-01]: specifies the
additional running time on the maximum running time at
outdoor temperature [4-02] or [F-01]. See figure below.
Heating
Cooling
t
t
[8-01]+
[8-04]
[8-01]+
[8-04]
[8-02]
[8-02]
[8-01]
[8-01]
1
0
0
t
1
TA
[5-03]
[4-02]
4
0
TA
[F-01]
35°C
TA
Time
Ambient (outdoor) temperature
maximum running time
3
0
anti-recycle time
1
The full advantage of [8-04] will be applicable if setting
[4-03] is not 1.
0
1
[9] The purpose of this field setting is to prevent the user from
selecting a wrong (i.e., too hot or too cold) leaving water temperature.
Thereto the heating temperature set point range and the cooling
temperature set point range available to the user can be configured.
0
t
[8-03]
1
Booster heater operation (1 = active, 0 = not active)
2
Heat pump domestic water heating mode
(1 = active, 0 = not active)
3
Hot water request for booster heater
(1 = request, 0 = no request)
4
Hot water request for heat pump (1 = request, 0 = no request)
t
Time
■
In case of a floor heating application, it is important to
limit the maximum leaving water temperature at
heating operation according to the specifications of
the floor heating installation.
■
In case of a floor cooling application, it is important to
limit the minimum leaving water temperature at
cooling operation (field setting of parameter [9-03]) to
60.8~64.4°F (16~18°C) to prevent condensation on
the floor.
■
By adapting the booster heater delay time versus the
maximum running time, an optional balance can be
found between the energy efficiency and the heat up
time.
■ [9-00] Heating set point upper limit: maximum leaving water
temperature for heating operation.
■
However, if the booster heater delay time is set too
high, it might take a long time before the domestic hot
water reaches its set temperature upon domestic hot
water mode request.
■ [9-02] Cooling set point upper limit: maximum leaving water
temperature for cooling operation.
■
The purpose of [8-03] is to delay the booster heater in
relation with the heat pump operation time in domestic
water heating mode.
■
The setting [8-03] has only meaning if setting
[4-03]=1. Setting [4-03]=0/2/3 limits the booster
heater automatically in relation to heat pump
operation time in domestic water heating mode.
■
Take care that [8-03] is always in relation with the
maximum running time [8-01].
Example: [4-03]=1
100
CAUTION
Energy saving settings
Quick heating settings
(default)
[8-01]
20~95 min
30 min
[8-03]
[8-01] + 20 min
20 min
■ [9-01] Heating set point lower limit: minimum leaving water
temperature for heating operation.
■ [9-03] Cooling set point lower limit: minimum leaving water
temperature for cooling operation.
■ [9-04] Overshoot setting: defines how much the water
temperature may rise above the set point before the
compressor stops. This function is only applicable in heating
mode.
DACA-EEDEN09-720
[A] Quiet mode
This field setting allows to select the desired quiet mode. Two quiet
modes are available: quiet mode A and quiet mode B.
■ [C-04] Bivalent hysteresis: defines the temperature difference
between bivalent ON temperature and bivalent OFF
temperature.
Permission signal X1–X2 (EKRP1HB)
In quiet mode A, priority is given to the unit operating quietly under all
circumstances. Fan and compressor speed (and thus performance)
will be limited to a certain percentage of the speed at normal
operation. In certain cases, this might result in reduced performance.
closed
[C-04]
open
In quiet mode B, quiet operation might be overridden when higher
performance is required. In certain cases, this might result in less
quiet operation of the unit to meet the requested performance.
TA
■ [A-00] Quiet mode type: defines whether quiet mode A (0) or
quiet mode B (2) is selected.
Make sure to observe all rules mentioned in
application 5 when bivalent operation function is
enabled.
Daikin shall not be held liable for any damage
resulting from failure to observe this rule.
Do not set other values than the ones mentioned.
[C] Setup on EKRP1HB digital I/O PCB
■
In case the unit is single phase, the combination
of setting [4-03]=0/2 with bivalent operation at
low outdoor temperature can result in domestic
hot water shortage.
■
The bivalent operation function has no impact on
the domestic water heating mode. The domestic
hot water is still and only heated by the unit.
■
The permission signal for the auxiliary boiler is
located on the EKRP1HB (digital I/O PCB).
When it is activated, the contact X1, X2 is closed
and open when it is disactivated. See figure for
the schematic location of this contact.
Solar priority mode
■ [C-00] Solar priority mode setting: for information concerning
the EKSOLHW solar kit, refer to the installation manual of
that kit.
Alarm output logic
Alarm
No alarm
No power supply
to unit
0
(default)
Closed output
Open output
Open output
1
Open output
Closed output
Open output
X1 X2 X3 X4
■ [C-01] Alarm output logic: defines the logic of the alarm
output on the EKRP1HB digital I/O PCB.
[C-01]=0, the alarm output will be powered when an alarm
occurs (default).
[C-01]=1, the alarm output will not be powered when an
alarm occurs. This field setting allows for distinction between
detection of an alarm and detection of a power failure to the
unit.
[C-01]
Outdoor temperature
CAUTION
■ [A-01] Parameter 01: do not change this setting. Leave it set
to its default value.
NOTE
TA
[C-03]
X2M
OFF ON
SS1
Bivalent operation
X1M
Applies only to installations with an auxiliary boiler (alternating
operation, parallel connected). The purpose of this function is to
determine —based on the outdoor temperature— which heating
source can/will provide the space heating, either the Daikin unit or an
auxiliary boiler.
The field setting "bivalent operation" apply only the unit space
heating operation and the permission signal for the auxiliary boiler.
When the "bivalent operation" function is enabled, the unit will stop
automatically in space heating operation when the outdoor
temperature drops below "bivalent ON temperature" and the
permission signal for the auxiliary boiler becomes active.
When the bivalent operation function is disabled, the space heating
by unit is possible at all outdoor temperatures (see operation ranges)
and permission signal for auxiliary boiler is always disactivated.
■ [C-02] Bivalent operation status: defines whether bivalent
operation is enabled (1) or disabled (0).
■ [C-03] Bivalent ON temperature: defines the outdoor
temperature below which the permission signal for the
auxiliary boiler will be active (closed, KCR on EKRP1HB) and
space heating by indoor unit will be stopped.
YC Y1 Y2 Y3 Y4
[D] Benefit kWh rate power supply/Local shift value weather
dependent
Benefit kWh rate power supply
■ [D-00] Switching off heaters: Defines which heaters are
switched off when the benefit kWh rate signal of the
electricity company is received.
If [D-01]=1 or 2 and the benefit kWh rate signal of the
electricity company is received, following devices will be
switched off:
[D-00]
Compressor
Back up heater
Booster heater
0
(default)
Forced off
Forced off
Forced off
1
Forced off
Forced off
Permitted
2
Forced off
Permitted
Forced off
3
Forced off
Permitted
Permitted
[D-00] settings 1, 2 and 3 are only meaningful if the
benefit kWh rate power supply is of the type that
power supply is not interrupted,
101
DACA-EEDEN09-720
Field settings table
4EMPERATUREVALUESDISPLAYEDONTHEDIGITALCONTROLLERUSERINTERFACEAREIN—#
4EMPERATUREVALUESIN—#AREBETWEENBRACKETS#ONVERSIONFROM—#TO—&ISFORINFORMATIONONLY
First
code
Second
code
User permission level
Weather dependent set point
5SERPERMISSIONLEVEL
Value
Date
Value
Default
value
Range
Step
Unit
ˆ
,OWAMBIENTTEMPERATURE,O?!
n
n^
n^
—&
—#
(IGHAMBIENTTEMPERATURE(I?!
^
^
—&
—#
3ETPOINTATLOWAMBIENTTEMPERATURE,O?4)
^
^
—&
—#
3ETPOINTATHIGHAMBIENTTEMPERATURE(I?4)
^
^
—&
—#
&RI
-ON^3UN
!LL
ˆ
ˆ
Disinfection function
/PERATIONINTERVAL
3TATUS
/.
ˆ
ˆ
3TARTTIME
^
HOUR
3ETPOINT
^
^
—&
—#
)NTERVAL
^
MIN
/.
ˆ
ˆ
ˆ
Auto restart
3TATUS
Backup/booster heater operation and space heating off temperature
3TATUS
/.
ˆ
0RIORITY
/&&
ˆ
ˆ
3PACEHEATINGOFFTEMPERATURE
^
^
—&
—#
"OOSTERHEATEROPERATION
ˆ
ˆ
&REEZEUPPROTECTIONFUNCTIONMONOBLOCONLY
ˆ
ˆ
ˆ
ACTIVE
2EAD
ONLY
Equilibrium temperature and space heating priority temperature
%QUILIBRIUMTEMPERATURESTATUS
%QUILIBRIUMTEMPERATURE
3PACEHEATINGPRIORITYSTATUS
/&&
ˆ
ˆ
3PACEHEATINGPRIORITYTEMPERATURE
^
n^
—&
—#
3ETPOINTCORRECTIONFORDOMESTICHOTWATER
TEMPERATURE
^
^
—&
—#
/.
ˆ
ˆ
^
n^
—&
—#
DT for heat pump domestic water heating mode
3TART
^
^
—&
—#
3TOP
^
^
—&
—#
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
^
^
—&
—#
^
^
—&
—#
ˆ
ˆ
^
^
^
^
—&
—#
^
^
—&
—#
MIN
DT for booster heater and dual set point control
$OMESTICHOTWATERSTEPLENGTH
(YSTERESISVALUEBOOSTERHEATER
$UALSETPOINTCONTROLSTATUS
3ECONDSETPOINTHEATING
Date
102
Installer setting at variance with default value
Setting name
3ECONDSETPOINTCOOLING
Domestic water heating mode timer
-INIMUMRUNNINGTIME
^
-AXIMUMRUNNINGTIME
^
MIN
!NTIRECYCLINGTIME
^
HOUR
"OOSTERHEATERDELAYTIME
^
MIN
!DDITIONALRUNNINGTIMEAT;=;&=
^
MIN
DACA-EEDEN09-720
First
code
!
B
#
$
%
&
Second
code
Installer setting at variance with default value
Setting name
Value
Date
Value
Default
value
Range
Step
Unit
Cooling and heating set point ranges
(EATINGSETPOINTUPPERLIMIT
^
^
—&
—#
(EATINGSETPOINTLOWERLIMIT
^
^
—&
—#
#OOLINGSETPOINTUPPERLIMIT
^
^
—&
—#
#OOLINGSETPOINTLOWERLIMIT
^
^
—&
—#
/VERSHOOTSETTINGA
^
^
—&
—#
ˆ
Quiet mode
1UIETMODETYPE
ˆ
0ARAMETER
ˆ
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
.OTAPPLICABLE
2EADONLY
ˆ
ˆ
Setup on EKRP1HB digital I/O PCB
3OLARPRIORITYMODESETTING
ˆ
!LARMOUTPUTLOGIC
ˆ
ˆ
"IVALENTOPERATIONSTATUS
ˆ
ˆ
"IVALENT/.TEMPERATURE
n^
n^
—&
—#
"IVALENTHYSTERESIS
^
^
—&
—#
ˆ
Benefit kWh rate power supply/local shift value weather dependent
3WITCHINGOFFHEATERS
ˆ
5NITCONNECTIONTOBENEFITK7H ATEPOWERSUPPLY
/&&
ˆ
ˆ
.OTAPPLICABLE$ONOTCHANGETHEDEFAULTVALUE
ˆ
ˆ
ˆ
,OCALSHIFTVALUEWEATHERDEPENDENT
ˆ
ˆ
Unit information readout
3OFTWAREVERSION
2EAD
ONLY
ˆ
ˆ
ˆ
%%02/-VERSION
2EAD
ONLY
ˆ
ˆ
ˆ
5NITMODELIDENTIFICATIO
2EAD
ONLY
ˆ
ˆ
ˆ
,IQUIDREFRIGERANTTEMPERATURE
2EAD
ONLY
ˆ
ˆ
—&
—#
)NLETWATERTEMPERATURE
2EAD
ONLY
ˆ
ˆ
—&
—#
Option setup
0UMPOPERATION
ˆ
ˆ
3PACECOOLINGPERMISSIONTEMPERATURE
^
^
—&
—#
"OTTOMPLATEHEATER/.TEMPERATURE
^
^
—&
—#
"OTTOMPLATEHEATERHYSTERESIS
^
^
—&
—#
&UNCTIONALITYOF8!
ˆ
ˆ
A /NLYPOSSIBLETOMODIFYTHEFIRSTMI UTESAFTERPOWER/.
103
Date
The present publication is drawn up by way of information only and does not constitute an offer binding upon Daikin Europe N.V. Daikin Europe N.V. has compiled the
content of this publication to the best of its knowledge. No express or implied warranty is given for the completeness, accuracy, reliability or fitness for particular purpose
of its content and the products and services presented therein. Specifications are subject to change without prior notice. Daikin Europe N.V. explicitly rejects any liability
for any direct or indirect damage, in the broadest sense, arising from or related to the use and/or interpretation of this publication. All content is copyrighted by Daikin
Europe N.V.
technical data
Daikin’s unique position as a manufacturer of
air conditioning equipment, compressors and
refrigerants has led to its close involvement in
environmental issues. For several years,
Daikin has had the intention of becoming a
leader in the the provision of products that
have limited impact on the environment. This
challenge demands the eco design and
development of a wide range of products and
an energy management system, resulting in
energy conservation and reduction of waste.
ISO14001 assures an effective
environmental management system in
order to help protect human health and the
environment from the potential impact of our
activities, products, and services and to
assist in maintaining and improving the
quality of the environment.
Daikin Europe N.V. is approved by LRQA for
its Quality Management System in
accordance with the ISO9001 standard.
ISO9001 pertains to quality assurance
regarding design, development, and
manufacturing, as well as to services related
to the product.
Daikin units comply with the European
regulations that guarantee the safety of
the product.
DAIKIN EUROPE N.V.
Naamloze Vennootschap
Zandvoordestraat 300
B-8400 Oostende, Belgium
www.daikin.eu
BTW: BE 0412 120 336
RPR Oostende
DAIKIN AC (AMERICAS), INC.
1645 Wallace Drive, Suite 110
Carrollton, TX 75006
info@daikinac.com
www.daikinac.com
DACA-EEDEN09-720
Printed in U.S.A. 03/2010 B AK
Specifications, designs and other content appearing in this brochure are current as of March 2010 but subject to change without notice.
Download PDF