Eastern Tools & Equipment | TG72B12 | Specifications | Eastern Tools & Equipment TG72B12 Specifications

Eastern Tools & Equipment TG72B12 Specifications
Eastern Tools & Equipment, Inc
TG72B12 Portable Generator
8250 Surge Watts
7250 Continuous Watts
Customer Service (888)-908-6200
www.easterntools.com
Eastern Tools & Equipment. Inc
Ontario, CA U.S.A
1
Thank you for purchasing products from EASTERNTOOLS & EQUIPMENT, INC. We appreciate your
business. The following manual is only a guide to assist you and is not a complete or
comprehensive manual of all aspects of maintaining and repairing your generator. The equipment
you have purchased is a complex piece of machinery. We recommend that that you consult with a
dealer if you have doubts or concerns as to your experience or ability to properly maintain or repair
your equipment. You will save time and the inconvenience of having to go back to the store if you
choose to write or call us concerning missing parts, service questions, operating advice, and/or
assembly questions.
This manual will explain how to operate and service your generator set.
Please fill out the information below. This will help you save time if you ever need to provide the
following information for a warranty repair.
GENERATOR
Model Number: _________________________________________
Serial Number: __________________________________________
ENGINE
Model Number: _________________________________________
DATE PURCHASED: ________________Day _______________Month ________________YEAR
TABLE OF CONTENTS
Safety warning
3
Specifications/Oil
4
Control and Features
5
Handle and Wheel Kit
6
Auto throttle switch
7
Connecting the battery
7
Starting the unit
7
Connecting loads
8
Stopping the unit
8
Maintenance
8
Trouble shooting
10
Wire Diagram
11
Parts Diagram
12
Warranty
13
2
Safety Warning
Please read this manual to understand how to
use your unit as well as understanding the risk
the come with the unit.
ELECTRIC SHOCK AND SHORT CIRCUIT
Be sure to notify the utility company
when using the generator for backup
NOTICE exceeding your generator wattage/
power. Use approved transfer
amperage coverage capacity can damage your
equipment to isolate the generator from electric
unit as well as any devices attached to your unit. utility. In highly conductive area such as metal
decking or steel work, use a ground circuit fault
Consumers should notice that this manual might interrupter. Never touch the generator if the
generator is wet. Also, never touch the
differ slightly from the actual product as more
improvements are made to our products. Some generator if your hand is wet. Never operate
of the pictures in this manual may differ slightly your generator if the weather conditions call for
any type of precipitation such as rain, snow, or
from the actual product as well. Eastern Tools
fog.
and Equipment, Inc. reserves the right to make
changes at any time without notice and without
incurring any obligation
Do not use electrical cords that have been
damaged (worn, bare, frayed)
CARBON MONOXIDE WARNING
Do not touch bare receptacles or wires
Do not allow children to operate the generator.
FUEL SAFETY
When using the LPG generator, please be sure
that there is some distance between LGP tank
and the LPG generator, to prevent unnecessary
Operate the generator ONLY outdoors. Never
danger because of the high temperature surface
run the generator indoors as the engine gives
area of the LPG tank. When using the unit,
off poisonous carbon monoxide, an odorless and please check the surface temperature of the
colorless gas. Inhaling carbon monoxide will
LPG tank.
cause nausea, fainting or death. Also, keep the
generator at least 3 feet away from flammable
Place the generator in a well-ventilated area. DO
matter for adequate ventilation
NOT place the generator near vents or intakes
where exhaust fumes could be drawn into
occupied or confined spaces. Carefully consider
GROUNDING THE UNIT
wind and air currents when positioning
Always properly ground the generator. Failing to generator. Please do not light a cigarette near
the LPG generator.
do so can result in electrocution, particularly if
the generator is equipped with a wheel kit.
GENERATOR SAFETY
Do not start generator with electrical devices
connected to it. Start the generator first and
after the speed of the generator stabilizes,
electrical loads can be applied to it.
When connecting electrical loads, make sure the
devices are "OFF" first before connecting them.
3
Keep the same concept when disconnecting
electrical devices; make sure all devices are in
the "OFF" position before disconnecting.
2. Allow the oil to drain completely.
3. Replace the drain plug.
4. Remove oil fill cap/dipstick to add oil.
5. Add 33.8 oz (1 L) of oil and replace oil fill
cap/dipstick.
Operate the generator on level surfaces only.
Inclined surfaces reduce the effective lubrication 6. Dispose of used oil at an approved waste
management facility.
of the engine.
Do not expose the generator to excessive
moisture, dust, dirt, or corrosive vapors.
NOTICE poor treatment of your equipment
can greatly reduce the life of the LPG generator.
Use the generator for its intended usage. If you
have any concerns about maintain your unit
contact a local service center or called customer
service (888)-696-2345. Operate the LPG
generator on a level surface and do not place
objects in the units recoil slots.
Oil capacity is 33.8 oz (1 L).
Generator Specifications
Running Wattage
7250 Watts
Starting Wattage
8250 Watts
AC Load
120V/240V
Phase
Single
T.H.D.
<5%
Weight
193.8 lbs. (87.9 kg)
Height
27.625 inches (70.2
cm)
Width
20.75 inches (52.7
cm)
Length
23.25 inches (59.1
cm)
SPARK PLUGS
1. Remove the spark plug cable from the spark
plug.
2. Use the spark plug tool that shipped with
your generator to remove the plug.
3. Inspect the electrode on the plug. It must be
clean and not worn to produce the spark
required for ignition.
4. Make certain the spark plug gap is 0.7 0.8mm (0.028 - 0.031 in.).
5. Refer to the spark plug recommendation
chart when replacing the plug.
6. Carefully thread the plug into the engine.
7. Use the spark plug tool to firmly install the
plug.
8. Attach the spark plug wire to the plug.
Your generator comes equipped with a ¾” long
reach plug (18 mm)
Intermittent use (less than 1 hour/month) or
colder temperatures (below 60°F)
NGK B4ES or STAR F6TC
OIL
Moderate use (less than 3 hours/month) or
Change oil when the engine is warm. Refer to
the oil specification to select the proper grade of Seasonal temperatures (50-80°F)
NGK B4ES or STAR F6TC
oil for your operating environment.
Extreme use (continuous) or hot climates(80100°F)NGK B4ES or STAR F6TC
1. Remove the oil drain plug with a 15 mm
socket and extension.
Frequency
60Hz
4
Controls and Features
Read this owner’s manual before operating your generator. Familiarize yourself with the location
and function of the controls and features. Save this manual for future reference.
(20)
(1)
(21)
(2)
(5)
(18)
(4)
(19)
(17)
(16)
(6)
(9)
(14)
(15) (13)
(8)
(11) (12)(10)
(7)
(9)
(1) FUEL TANK CAP
(12) CAP ASSY,OIL FILLER
(2) MUFFLER COMP
(13) OIL INDICATOR LIGHT ASSY
(3) CIRCUIT BREAKER(30A)
(14) PUSHBUTTON ELECTRICITY STARTUP
SWITCH
(15) STAND ASSY
(4) CIRCUIT BREAKER(30A)
(5) 240/120V LOCKING RECEPTACLE L14-30
(6) LUG GROUND
(7) 3-POLE RECEPTACLE L5-30R
(8) 120V RECEPTACLE 5-20R
(9) WHEEL 10"
(10) BATTERY KICKSTAND
(11) CIRCUIT BREAKER(20A)
(16) STARTER ASSY,RECOIL
(17) AIR/C ASSY
(18) COCK ASSY.FUEL
(19) CHOKE SET ASSY
(20) TANK COMP,FUEL
(21) FRAME ASSY
WARNING: DO NOT exceed the generator’s wattage/amperage capacity. Our products are
continuously being changed and improved. Every effort has been made to ensure that information
in the manual is accurate and up to date. However, we reserve the right to change, alter or
otherwise improve the product and this manual at any time without prior notice.
PACKAGE CONTENTS
Your generator comes with the items listed below. Please check to see that all of the following
items are included with your generator.
If you are missing components DO NOT RETURN TO STORE, please call (888)908-6200 for
customer service.
5
(
Order
No.
1
Name
Air-cooled generator set
Tool Kit:
Qty
1
Flat Head Screwdriver
Spark Plug Wrench
2
1
Wrench, 8×10,17×19
Battery Wire
Assembly Kit:
3
Wheel (2 pcs)
1
Wheel Kit Hardware
1
Generator Foot (2 pcs)
1
Handle
1
Assembly Kit:
4
Assembly Kit:
5
etc.
Assembly Kit:
6
吊钩Suspend
7
8
Conveyance Suspend
Owner’s manual
1
1
6
2. CONNECTING THE BATTERY'S
CATHODE:
AUTO THROTTLE CONTROL SWITCH
When using the generator, leave the AUTO
THROTTLE CONTROL SWITCH (ATC) in the “ON”
position; as soon as output is not needed. The
engine will go into idle speed thus saving fuel.
As soon as, power is need again the engine will
operate as normal again.
a. Connect one end of the white cable to the
(negative) " - " end and fasten it.
Battery cable installation instructions:
1. CONNECTING THE BATTERY'S
ANODE
b. After attaching the cable to the cathode.
Please remember to attach the rubber safety
over the cathode (as illustrated in this picture).
a. Connect one end of the red cable to the
(positive) " + " end and fasten it.
c. Connect the other end of the white cable to
the bearing support of the alternator and fasten
it.
b. After attaching the cable to the anode please
remember to attach the rubber safety over the
anode (as illustrated in this picture).
c. Connect the other end of the red cable to the
output end relay.
7
STARTING THE UNIT
MAINTENANCE
Please refer to your start up guide that comes
with your unit.
Generator maintenance consists of keeping the
unit clean and dry. Be sure to store the unit in a
clean and dry environment, where it will not be
exposed to excessive dust, dirt, moisture or any
corrosive vapors. Cooling slots should always be
clean and free from clogs.
Before beginning your work, you must verify
that the rated (running) and surge (starting)
watts for the items you will power at the same
time are within the generators operating
capacity. Please refer to the following Table 1
for wattage / amperage ratings. Also, to prolong
the life of your generator, prolong the life of
your generator, sequentially add loads and
permit the generator to stabilize before adding
another load. Never exceed the capacity of the
generator.
Note: Do not use a garden hose to clean the
generator. Water can enter the fuel and intake
system and cause problems. In addition, if water
and dirt buildup on the generators internal
windings, the resistance of these windings will
decrease.

Estimate how many surge (starting) watts you
will need. Surge wattage is the short burst of
power needed to start electric motor-driven
tools or appliances such as a circular saw or
refrigerator.



Note: Check your electrical device for actual
wattage.
To clean the generator, use a damp cloth
to wipe the exterior surfaces.
Use a soft bristle brush to loosen caked on
dirt of oil.
Use a vacuum cleaner to pick up loose dirt
and debris.
Compressed air (not to exceed 25 psi) may
be used to blow away dirt.
SPARK PLUG
Stopping the Engine
1.Turn off and unplug all electrical loads. Never
start or stop the generator with electrical
devices plugged in or turned on.


Remove the spark plug
Remove the carbon deposits

Check for discoloration. Standard is tan in
color.
Check spark plug gap

2.Let the generator run at no-load for several
minutes to stabilize internal temperatures of the
engine and generator.
3. Turn the ignition switch to the “Off” position.
Make certain the spark plug gap is
0.7 -0.8mm (0.028 - 0.031 in.).
4.Turn the fuel valve to the “Off” position.
8
AIR FILTER


Unscrew the bolt from the air cleaner
cover, and remove the air cleaner cover.
Check the air cleaner element to be sure
they are clean and in good condition.
L13-30R: 120V, 30Amp Twist Lock Receptacle

If the air filter is dirty, remove and clean
the element.

Wash in solvent

Squeeze

Soak oil

Squeeze dry
STORAGE
The generator should be started at least once
every week. If this cannot be done and you must
store the unit more than 30 days, please follow
the following guidelines.
·Close the fuel valve: drain the fuel from the fuel
tank.

Reinstall the air cleaner element and
secure the cover by setting the cover
spring.
RECEPTACLES
·Drain the fuel from the carburetor .
This generator is equipped with the following
Receptacles
NEMA 5-20R: 125 Volt, 20 Amp GFCI Duplex
Receptacle
·Remove the oil filter cap and drain plug to drain
the oil.
L5-30R: 120V, 30Amp Twist Lock Receptacle
9
MAINTENANCE
·Tighten the oil drain plug and fill the engine
with new oil to the filter neck.
·Pull the starter grip carefully until
resistance is felt.
·Store the generator in a clean area.
Below is a routine maintenance schedule.
(1):These items should be serviced by a dealer.
(2):Every 3 years.
10
TROUBLE SHOOTING
Problem
Generator will not start
Cause
Solution
No Gasoline
Add Gasoline
Faulty spark plug
Replace spark plug
Unit loaded during start up
Remove load from unit
Low oil level
Fill crankcase to the proper level
Place generator on a flat, level
surface
Choke in the wrong
position.
Spark plug wire loose
Adjust choke.
Generator shuts down
during
operation
Out of Gasoline
Refill gasoline
Low oil level
Fill crankcase to the proper level.
Place generator on a flat, level
surface
Generator cannot supply
enough
power or overheating
Generator is overloaded
Review load and adjust. See “Power
Management”
Insufficient ventilation
Check for air restriction. Move to a
well ventilated area
Cable not properly
connected
Connected device is
defective
Circuit breaker is open
Check all connections
Capacitor defective
Replace capacitor (Service Center)
Faulty brush assembly
Replace brush assembly (Service
Center)
Faulty AVR
Replace AVR (Service Center)
Loose wiring
Generator will not start;
Generator starts but runs
roughly
No AC output
Attach wire to spark plug
Replace defective device
Reset circuit breaker
Other
Inspect and tighten wiring
connections
Contact the help line.
Generator gallops
Engine governor defective
Contact the help line
Repeated circuit breaker
tripping
Overload
Review load and adjust. See “Power
Management”
Faulty cords or device
Check for damaged, bare or frayed
wires. Replace defective device
11
WIRING DIAGRAM
12
Parts List
13
14
15
16
17
18
LIMITED WARRANTY
Eastern Tools & Equipment, Inc. will repair or replace, free of charge, any part or parts of the
generator that are defective in material or workmanship or both. Transportation charges on parts
submitted for repair or replacement under this Warranty must be borne by purchaser. This
warranty is effective for the time period and subject to the conditions provided for in this policy.
For warranty service, find the nearest Authorized Service Dealer by contacting the place of
purchase or Eastern Tools & Equipment, Inc. THERE IS NO OTHER EXPRESSED WARRANTY. IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITED BY LAW
ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES
UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY
LAW. Some states do not allow limitations on how long an implied warranty lasts, and some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights, which vary from state to state.
Eastern Tools & Equipment, Inc.
WARRANTY PERIOD***
WITHIN U.S.A AND CANADA
ENGINES
CONSUMER USE
COMMERCIAL
USE
90 days
OUTSIDE U.S.A. AND CANADA
CONSUMER USE
COMMERCIAL
USE
90 days
GASOLINE
1 year
1 year
GENERATOR
The warranty period begins on the date of purchase by the first retail consumer or commercial end
user, and continues for the period of time stated in the table above. “Consumer use” means
personal residential household use by a retail consumer. “Commercial use” means all other uses,
including the commercial, income producing or rental purpose. Once the engine has experienced
commercial use, it shall thereafter be considered as a commercial use engine for purpose of this
warranty. Engines use in competitive racing or commercial or rental tracks are not warranted.
***A two-year warranty applies to the emission control system on engines certified by EPA and
CARB.
IMPORTANT
“WARRANTY REGISTRATIONS IS NECESSARY TO OBTAIN LIMITED WARRANTY ON EASTERN TOOLS &
EQUIPMENT, INC., ENGINES. THE WARRANTY REGISTRATION CARD MUST BE RETURNED WITHIN 15 DAYS OF
PURCHASE FOR LIMITED WARRANTY TO BE VALID”
About Your Product Warranty
Eastern Tools & Equipment, Inc. welcomes warranty repair and apologizes to you for being
inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty
repairs are handled routinely, but sometimes warranty service may be inappropriate. For example,
warranty would not apply if an engine is damaged because of misuse, lack of routine maintenance,
shipping, handling, warehousing and improper installation. Similarly, warranty is void if the serial
number on the engine has been removed or if the engine has been altered or modified. If a
customer differs with the decision of the Service Dealer, an investigation will be made to determine
whether the warranty applies. Ask the Service Dealer to submit all supporting facts to his
Distributor or the factory for review. If the distributor or the factory decides that the claim is
justified, the customer will be fully reimbursed for those items that are defective. To avoid
misunderstanding, which might occur between the customer and the dealer, listed below are some
of the causes of engine failure that the warranty does not cover
19
Normal wear:
Engines and generators, like all mechanical devices, need periodic parts service and replacement to
perform well. Warranty will not cover repair when normal use has exhausted the life of a part of an
engine.
Improper maintenance:
The life of an engine or your equipment depends upon the conditions under which it operates, and
the care it receives. Some applications, such as tillers, pumps, and rotary movers, are very often
used in dusty or dirty conditions, which can cause what appears to be premature, wear. Such wear,
when caused by dirt, dust, spark pug cleaning grit, or other abrasive material that has entered the
engine because of improper maintenance is not covered by warranty.
This warranty cover engine related defective material and/or workmanship only, and not
replacement or refund of the equipment to which the engine may be mounted. Nor des the
warranty extend to repairs required because of:
1.
2.
Problems caused by parts that are not original eastern tools & equipment, inc., parts.
Equipment controls or installations that prevent starting, cause unsatisfactory engine
performance, or shorten engine life. (Contact equipment manufacturer.)
3. Leaking carburetor, clogged fuel pipes, sticking valves, or other damage, caused by using
contaminated or stale fuel. (Use clean, fresh, lead-free gasoline.)
4. Parts which are scored or broken because an engine was operated with insufficient or
contaminated lubricating oil, or and incorrect grad of lubricating oil (check oil level daily
or after every 8 hours of operation. Refill when necessary and change at recommended
intervals.) Engine damage may occur if oil level is not properly maintained. Read
Operating & Maintenance Instructions.
5. Repair or adjustment of associated parts or assemblies such as clutches, transmissions,
remote controls, etc., which are not manufactured by Eastern Tools & Equipment, Inc.
6. Damage or wear to parts caused by dirt, which entered the engine because of improper
air filter maintenance, re-assembly, or use of a non-original air filter element or
cartridge. Read Operating & Maintenance Instructions.
7. Parts damaged by over-speeding, or overheating caused by grass, debris, or dirt, which
plugs or clogs the cooling fins, or flywheel are, or damaged caused by operating the
engine in a confined area without sufficient ventilation.
8. Engine or equipment parts broken by excessive vibration caused by a loosen cutter
blades unbalanced blades or loose unbalanced impellers, improper attachment of
equipment to engine crankshaft, over speeding or other abuse in operation.
9. A bent or broken crankshaft, caused by striking a solid object with the cutter blade of a
rotary lawn mower, or excessive v-belt tightness.
10. Routine tune-up or adjustment of the engine.
11. Engine or engine component failure, i.e., combustion chamber, valves, valve seats, valve
guides, or burned starter motor winding, caused by the alternated fuels such as,
liquefied petroleum, natural gas, altered gasoline’s etc.
Warranty is available only through service dealers, which have been authorized by Eastern Tools
& Equipment, Inc., please contact the place of purchase or Eastern Tools & Equipment, Inc. for a
Service Dealer near you.
CALIFORNIA & USEPA EMISSION CONTROL WARRANTY STATEMENT
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB) and
Eastern Tools & Equipment, Inc. are pleased to explain the Federal and California Emission Control
System Warranty on your small nonroad engine. In California, new small nonroad engines must be
designed, built and equipped to meet the State’s stringent and anti-smog standards. Eastern Tools
& Equipment, Inc. must warrant the emission control system on your small nonroad engine for the
20
periods of time listed above listed above provided there has been no abuse, neglect or improper
maintenance of your small nonroad engine.
Your emission control system may include parts such as the carburetor, or fuel-injection system,
the ignition system and catalytic converter. Also included may be hoses, belts, connectors and
other emission-related assemblies.
Where a warrantable condition exists, Eastern Tools & Equipment, Inc. will repair your small
nonroad engine at no cost to you including diagnosis, parts and labor.
OWNER’S WARRANTY RESPONSIBILITIES
As the small nonroad engine owner, you are responsible for the performance of the required
maintenance listed in your Owner’s Manual. Eastern Tools & Equipment, Inc. recommends that you
retain all receipts covering maintenance on your small nonroad engine, but Eastern Tools &
Equipment, Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance.
As the small nonroad engine owner, you should, however, be aware that Eastern Tools &
Equipment, Inc. may deny you warranty coverage if your; small nonroad or part thereof has failed
due to abuse, neglect, improper maintenance or unapproved modifications.
You are responsible for presenting your small nonroad engine to Eastern Tools & Equipment, Inc.
distribution center as soon as a problem exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities or request warranty
service you should contact either the place of purchase or Eastern Tools & Equipment, Inc., c/o
Service Manager, Engine and Equipment Service Division.
IMPORTANT NOTE:
This warranty statement explains your rights and obligations under Emission Control system
Warranty (ECS Warranty), which is provided to our by Eastern Tools & Equipment, Inc. pursuant to
California law, Eastern Tools & Equipment, Inc. also provides to original purchasers of new Eastern
Tools & Equipment, Inc. engines. Eastern Tools & Equipment, Inc. Limited Warranties for New
engines & other Equipment associated with the engine (Eastern Tools & Equipment, Inc. Products
Warranty), which is enclosed with all New Eastern Tools & Equipment, Inc. engines and products on
a separate sheet. The ECS Warranty applies only to the emission control system of your new
engine. To the extent that there is any conflict in terms between the ECS Warranty and the Eastern
Tools & Equipment, Inc., Warranty, the ECS Warranty shall apply except in any circumstances in
which the Eastern Tools & Equipment, Inc. Product Warranty may provide a longer warranty
period. Both the ECS Warranty and the Eastern Tools & Equipment, Inc. product Warranty describe
important right and obligations with respect to your new engine.
Eastern Tools & Equipment, Inc. at its location in Ontario, California can perform warranty service
or any authorized service dealer near you. At the time of requesting warranty service, evidence
must be presented of the date of sale to the original purchaser. The purchaser shall pay any
charges for transporting the product to and from the place when the inspection and/or warranty
preformed. The purchaser shall be responsible for any damage or loss incurred in connection with
the transportation of any engine or any part(s) thereof submitted for inspection and/or warranty
work.
If you have any questions regarding your warranty rights and responsibilities, you should contact
Eastern Tools & Equipment, Inc.
21
PRODUCT REGISTRATION
For more efficient customer service, please fill out the information below and mail to Eastern Tools &
Equipment, Inc. Product Warranty and Registration Division.
Model No._________________
Engine Serial No.____________
Purchase Date ____/____/_____
Purchased from:
[ ] Retail Location
[ ] Private Consumer
[ ] Other________________________________
Name_________________________________________________________________________
Address_______________________________________________________________________
Telephone (____)________-____________
Purchased:
[ ] New
Purchase Price_____________
[ ] Used
Consumer Information:
Name_________________________________________ Telephone (____) ____ - ___________
Street Address________________________________________ Suite or Apt No.____________
City______________________________________ State_____ Zip Code___________________
Province or County______________________________________________________________
Are you a:
[ ] Business
[ ] Residence
Product Usage Information:
How often will you use this product?
[ ] Everyday
[ ] Periodically
[ ] Emergency Use Only
[ ] Other
What type of application will you use this product in?
[ ] Heavy Commercial
[ ] Moderate Commercial
[ ] Light Commercial
[ ] Tradeshows
[ ] Heavy Residential
[ ] Moderate Residential
[ ] Light Residential
[ ] Camping/Backpacking
[ ] Other___________________________________________________________________________
Important information:
It is critical to your warranty that the original point of sales receipt the retained by current consumer, and
in order to comply with Eastern Tools &Equipment Product Warranty statement you must return the
registration card within original purchase Product warranty is valid from original date of purchase.
Please mail the above card to:
Eastern Tools & Equipment, Inc.
600 Industrial Parkway
Norwalk, OH 44857
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising