Installation Guide
N750 Wireless Dual Band Gigabit Router
Step 1:
Step 2:
Unplug the power
to turn off your modem.
Connect one end of the
yellow Ethernet cable
to your modem, and the
other end to the Internet
port on your router.
Package Contents:
(not included)
Laptop or Desktop
Step 5:
Connect your computer
to the router ( ).
Use another Ethernet cable to
establish a wired connection
as shown in this diagram.
or Cable
Optionally, connect wirelessly
by using the preset wireless
security settings, located on
the bottom label.
Power On/Off
Power On/Off
Ethernet Cable
Step 3:
Plug in the power to
turn on your modem.
N750 Wireless Router
Power Adapter
Step 6:
N750 Wireless Router
Open a browser.
Step 4:
Wait approximately 2 minutes
until your modem turns on.
Connect the power adapter to the
router, then plug it into an outlet.
If your modem has
a battery backup,
first remove and reinsert
the battery before connecting
your modem to power.
Wait for the 2.4 GHz LED (
to turn on.
2.4 GHz
If none of the LEDs turn on, make sure
that the Power On/Off button is in the
ON position (pushed in).
If the web page does not
display, close and re-open
the browser, then enter
in the address bar, or
check the “Troubleshooting”
section on the back of
this installation guide.
Preset Wireless Security
This product has a unique Wi-Fi network name (SSID) and network key (password).
The default SSID and network key (password) are uniquely generated for every
device (like a serial number), to protect and maximize your wireless security. This
information is located on the label on the bottom of the product.
NETGEAR recommends that you do not change the preset Wi-Fi network name
(SSID) and network key (password). If you do change the settings, the information
on the bottom of the product does not apply.
Connect Wireless Devices to Your Router
Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless
computers, and other devices to your wireless network.
The browser cannot display the Web page.
• Make sure that the PC is connected to one of the four LAN Ethernet ports, or
wirelessly to the router.
• Make sure that the router is fully up and running. Its wireless LED should turn
• Close and re-open the browser to make sure that the browser does not cache
the previous page.
• Browse to
• If the PC is set to a static or fixed IP address (this is uncommon), change it to
obtain an IP address automatically from the router.
Manual Method
Open the software utility that manages your wireless connections on the
wireless device that you want to connect to your router (iPhone, laptop,
computer, gaming device). This utility scans for all wireless networks in your
2. Look for the preset NETGEAR wireless network name (SSID), and select it.
The preset Wi-Fi network name (SSID) is located on the product label on the
bottom of the router.
Note: If you changed the name of your network during the setup process, look
for that network name.
Enter the preset password (or your custom password if you changed it), and
click Connect.
4. Repeat steps 1–3 to add other wireless devices.
Find the preset Wireless Settings on your router and record them here:
Wi-Fi network name (SSID) ________________________________
Network key (password) __________________________________
If you change the preset wireless settings, record them here:
Wireless network name (SSID) _______________________________
Network key (password) _____________________________________
If necessary to retrieve or update your password, type in a Web browser, and log in using the
default user name (admin) and password (password).
WPS Method
If your wireless device supports WPS (Wi-Fi Protected Setup)—NETGEAR calls
this method Push 'N' Connect—you might be prompted to press the WPS button on
the router instead of entering a password. If this happens:
Press the WPS button
on the router.
Within 2 minutes, press the WPS button on the client device, or follow the
WPS instructions that came with your wireless device to complete the WPS
process. The device will then be connected to your router.
3. Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a WEP client
to your network using WPS, it will not work.
After installing your device, register at so you
can use our telephone support service. Also go to for
product updates, additional documentation, and support.
For the free Live Parental Controls centralized Internet site filtering software for your
router, download from:
For additional features, including Traffic Metering, ReadySHARE, Guest Access,
and others, log in to your router at:
For complete DoC please visit the NETGEAR EU Declarations of Conformity
website at:
For GNU General Public License (GPL) related information, please visit
Download the free Desktop
Automatically fix common network
problems and easily manage your
home network connections.
Select Wireless Settings to locate your wireless password.
August 2011
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European
Union, this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2011 by NETGEAR, Inc. NETGEAR,the NETGEAR logo, and Connect with Innovation are trademarks and/or
registered trademarks of NETGEAR, Inc.and/or its subsidiaries in the United States and/or other countries.
Information is subject to change without notice. Other brand and product names are trademarks or registered
trademarks of their respective holders.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF