MSI | WindBOX Series | User`s manual | MSI WindBOX Series User`s manual

MSI WindBOX Series User`s manual
WindBOX series
MS-9A45 Fanless Box PC
▍ Preface
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document,
but no guarantee is given as to the correctness of its contents. Our products
are under continual improvement and we reserve the right to make changes
without notice.
Trademarks
All trademarks are the properties of their respective owners.
■
■
■
■
■
■
■
MSI® is a registered trademark of Micro-Star Int’l Co.,Ltd.
NVIDIA® is a registered trademark of NVIDIA Corporation.
ATI® and AMD® are registered trademarks of AMD Corporation.
Intel® is a registered trademark of Intel Corporation.
Windows® is a registered trademark of Microsoft Corporation.
AMI® is a registered trademark of Advanced Micro Devices, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
Revision
Revision
Date
V1.0
2012/04
Technical Support
If a problem arises with your system and no solution can be obtained from
the user’s manual, please contact your place of purchase or local distributor.
Alternatively, please try the following help resources for further guidance.
■
■
Visit the MSI website for technical guide, BIOS updates, driver updates, and other information: http://www.msi.com/service/download/
Contact our technical staff at: http://support.msi.com/
ii
MS-9A45
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU
REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at:
http://www.msi.com/html/popup/csr/evmtprtt_pcm.html
Battery Information
European Union:
Batteries, battery packs, and accumulators should
not be disposed of as unsorted household waste.
Please use the public collection system to return,
recycle, or treat them in compliance with the local
regulations.
Taiwan:
For better environmental protection, waste batteries should be collected separately for recycling or
special disposal.
California, USA:
The button cell battery may contain perchlorate material and requires
special handling when recycled or disposed of in California.
For further information please visit:
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer.
iii
▍ Preface
Safety Instructions
■
■
■
■
■
■
■
■
■
■
■
■
Always read the safety instructions carefully.
Keep this User’s Manual for future reference.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
The openings on the enclosure are for air convection hence protects
the equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source and adjust properly
110/220V before connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do
not place anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or
module.
All cautions and warnings on the equipment should be noted.
Never pour any liquid into the opening that could damage or cause
electrical shock.
If any of the following situations arises, get the equipment checked
by service personnel:
◯
◯
◯
◯
The power cord or plug is damaged.
◯
◯
The equipment has dropped and damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well or you can not get it work according to User’s Manual.
The equipment has obvious sign of breakage.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60oC (140oF),
IT MAY DAMAGE THE EQUIPMENT.
警告使用者:
這是甲類資訊產品,在居住的環境中使用時,可能會造成無線電干擾,在這
種情況下,使用者會被要求採取某些適當的對策。
iv
MS-9A45
CE Conformity
Hereby, Micro-Star International CO., LTD declares that this device is in compliance with the essential safety requirements and
other relevant provisions set out in the European Directive.
FCC-B Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the measures listed below:
■
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1.
this device may not cause harmful interference, and
2.
this device must accept any interference received, including interference
that may cause undesired operation.
▍ Preface
WEEE Statement
ENGLISH
Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment,
Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and
electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the
end of their useful life.
DEUTSCH
Gemäß der Richtlinie 2002/96/EG über Elektro- und Elektronik-Altgeräte dürfen Elektround Elektronik-Altgeräte nicht mehr als kommunale Abfälle entsorgt werden. Wir haben
europaweit verschiedene Sammel- und Recyclingunternehmen beauftragt, die in die Europäische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus zurückzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich
an einer lokalen Altgerätesammelstelle in Ihrer Nähe.
FRANÇAIS
Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques
et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement
mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains
produits en fin de vie. Par conséquent vous pouvez retourner localement ces matériels
dans les points de collecte.
РУССКИЙ
В соответствии с директивой Европейского Союза (ЕС) по предотвращению
загрязнения окружающей среды использованным электрическим и электронным
оборудованием (директива WEEE 2002/96/EC), вступающей в силу 13 августа 2005
года, изделия, относящиеся к электрическому и электронному оборудованию, не могут
рассматриваться как бытовой мусор, поэтому производители вышеперечисленного
электронного оборудования обязаны принимать его для переработки по окончании
срока службы.
ESPAÑOL
Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/o equipos
electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados
como “eléctricos y equipos electrónicos” no pueden ser depositados en los contenedores
habituales de su municipio, los fabricantes de equipos electrónicos, están obligados a
hacerse cargo de dichos productos al termino de su período de vida.
vi
MS-9A45
NEDERLANDS
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en
Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen
niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden
verplicht om producten retour te nemen aan het eind van hun levenscyclus.
SRPSKI
Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju
pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan otpad i
proizvođači ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njihovog
uobičajenog veka trajanja.
POLSKI
Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą odpadów produktów elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13 sierpnia
2005, tzw. “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być traktowane jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani
do odbierania ich w momencie gdy produkt jest wycofywany z użycia.
TÜRKÇE
Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve
elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların
üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü
olacaktır.
ČESKY
Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elektronických výrobků
2002/96/EC platné od 13. srpna 2005 je zakázáno likvidovat “elektrické a elektronické
výrobky” v běžném komunálním odpadu a výrobci elektronických výrobků, na které se
tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět po skončení jejich
životnosti.
MAGYAR
Az Európai Unió („EU”) 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és
elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen
elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére
azok hasznos élettartama végén.
ITALIANO
In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei Materiali Elettrici
ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti
alla categoria dei Materiali Elettrici ed Elettronici non possono più essere eliminati come
rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla
fine del suo ciclo di vita.
vii
▍ Preface
Contents
Copyright Notice������������������������������������������������������������������������������������ ii
Trademarks�������������������������������������������������������������������������������������������� ii
Revision������������������������������������������������������������������������������������������������� ii
Technical Support��������������������������������������������������������������������������������� ii
Chemical Substances Information����������������������������������������������������� iii
Battery Information������������������������������������������������������������������������������ iii
Safety Instructions������������������������������������������������������������������������������� iv
CE Conformity��������������������������������������������������������������������������������������� v
FCC-B Radio Frequency Interference Statement������������������������������� v
WEEE Statement���������������������������������������������������������������������������������� vi
Chapter 1 Overview���������������������������������������������������������������������������� 1-1
Packing Contents������������������������������������������������������������������������� 1-2
System Overview������������������������������������������������������������������������� 1-3
System Specifications������������������������������������������������������������������ 1-6
Chapter 2 System Setup�������������������������������������������������������������������� 2-1
Installation Tools�������������������������������������������������������������������������� 2-2
System Setup������������������������������������������������������������������������������� 2-3
Chapter 3 BIOS Setup������������������������������������������������������������������������ 3-1
Entering Setup����������������������������������������������������������������������������� 3-2
The Menu Bar������������������������������������������������������������������������������ 3-4
Main��������������������������������������������������������������������������������������������� 3-5
Advanced������������������������������������������������������������������������������������� 3-6
Boot�������������������������������������������������������������������������������������������� 3-12
Security�������������������������������������������������������������������������������������� 3-13
Chipset��������������������������������������������������������������������������������������� 3-14
Power����������������������������������������������������������������������������������������� 3-15
Save & Exit�������������������������������������������������������������������������������� 3-17
viii
Chapter 1
Overview
Thank you for choosing the WindBOX, an excellent
industrial computer system from MSI.
The WindBOX eliminates the noise and the risk of
fan’s failure by adopting wide heatsink as fanless
solution. It also supports VESA wall-mount interface
for various scenarios like digital signage, thin client,
and POS with affordable expenditure, which not only
meets the demand of Industrial applications but also
fulfills the needs of companies, governments, and institutes for general applications.
▍ Overview
Packing Contents
Power Adapter
MS-9A45 System
Power Cord
VESA Mount Plate
User’s Manual
Wireless LAN Antenna
Driver/Utility Disk
■ Please contact us immediately if any of the item is damaged or missing.
■ The picture is for your reference only and your packing contents may slightly
vary depending on the model you purchased.
1-2
MS-9A45
System Overview
 Side View-1
4
1
2
3
1
Gigabit LAN Jack
2
Headphone Jack (Green)
3
Microphone Jack (Pink)
4
USB Port
5
6
The standard RJ-45 LAN jack is for connection to the Local Area Network
(LAN). You can connect a network cable to it.
This connector is provided for headphones or speakers.
This connector is provided for microphones.
The USB (Universal Serial Bus) port is for attaching USB devices such as
keyboard, mouse, or other USB-compatible devices.
1-3
▍ Overview
1-4
5
DVI-I Port
6
Antenna Connector
The DVI-I (Digital Visual Interface-Integrated) connector allows you to connect an LCD monitor. It provides a high-speed digital interconnection between the computer and its display device. To connect an LCD monitor,
simply plug your monitor cable into the DVI connector, and make sure that
the other end of the cable is properly connected to your monitor (refer to your
monitor manual for more information.)
This connector allows you to connect an external antenna for wireless LAN.
MS-9A45
 Side View-2
1
2
3
4
1
Antenna Connector (Optional)
2
USB Ports
3
HDMI-Out Port
5
6
This connector allows you to connect an external antenna for wireless LAN.
The USB (Universal Serial Bus) port is for attaching USB devices such as
keyboard, mouse, or other USB-compatible devices.
The High-Definition Multimedia Interface (HDMI) is an all-digital audio/video
interface capable of transmitting uncompressed streams. HDMI supports all
TV format, including standard, enhanced, or high-definition video, plus multichannel digital audio on a single cable.
4
Power Button
5
Serial Port
6
Power Jack
Press this button to turn the system on or off.
The serial port is a 16550A high speed communications port that sends/ receives 16 bytes FIFOs. You can attach a serial mouse or other serial devices
directly to the connector.
The power adapter converts AC power to DC power for this jack. Power supplied through this jack supplies power to the system. To prevent damage to
the system, always use the supplied power adapter.
1-5
▍ Overview
System Specifications
1-6
CPU
■ Intel Cedarview-D processor
Chipset
■ North Bridge: integrated with CPU
■ South Bridge: Intel NM10 chipset
Memory
■ 1 DDR3 1066MHz Non-ECC SO-DIMM slot
■ Supports the maximum of 4GB
LAN
■ 2 Intel 82574L GbE controllers
Storage
■ 2 SATA 3Gb/s ports by Intel NM10 chipset
Audio
■ HDA Codec by Realtek® ALC887
■ Compliant with Azalia 1.0 specs
Graphics
■ Intel 3600 series integrated Graphics Engine
■ Resolution up to 1920 x 1200 pixels
Left Panel
Input/Output
■
■
■
■
■
■
1 wireless LAN antenna connector (optional)
2 USB 2.0 ports
1 HDMI-Out port
1 power button
1 RS-232/422/485 serial port
1 DC power jack
Right
Panel
Input/Output
■
■
■
■
■
■
2 Gigabit LAN jacks
1 headphone/speaker jack (green)
1 microphone jack (pink)
1 USB 2.0 port
1 DVI-I port
1 wireless LAN antenna connector
Power
Supply
■ 40 watt power adapter with active PFC
■ Input: 100-240V~, 50-60Hz, 1.7A
■ Output: 20V
2.0A
Dimension
& Weight
■ 260 mm (W) X 180 mm (D) X 19 mm (H)
■ 1.08 Kg
MS-9A45
Regulatory Compliance
■ FCC Class B, CE, C-Tick, BSMI, VCCI, RoHS compliance
Environmental
■ Operating Temperature: 0oC to 60oC
■ Storage Temperature: -20oC to 80oC
■ Humidity: 0% ~ 90% RH, non-condensing
1-7
Chapter 2
System Setup
This chapter provides you with the information on
hardware setup procedures. While doing the installation, be careful in holding the components and follow
the installation procedures. For some components, if
you install in the wrong orientation, the components
will not work properly.
Use a grounded wrist strap before handling computer
components. Static electricity may damage the components.
Important
•
Always unplug the power cord before installing
any components.
•
When the operating temperature reaches 40oC or
higher, please replace your HDD with SSD (SolidState Drive) or other types of heat-resistant HDD
to protect your HDD from being damaged by high
temperature.
▍ System Setup
Installation Tools
A Phillips (crosshead) screwdriver and a flathead screwdriver, can be used to do most of the installation. Choose
one with a magnetic head would be better.
Pliers, can be used as an auxiliary tool to connect some
connectors or cables.
Forceps, can be used to pick up tiny screws or set up
the jumpers.
Rubber gloves, can prevent yourself from being incised
and suffering the static charge.
2-2
MS-9A45
System Setup
Step 1:
Locate the VESA mount screw holes on the back of the LCD monitor.
Step 2:
Fasten the VESA mount plate to the monitor with the supplied screws.
2-3
▍ System Setup
Step 3:
Mount the system onto the VESA mount plate.
Step 4:
Tighten the thumbscrew at the bottom of the VESA mount plate to secure
the system.
2-4
MS-9A45
Step 5:
Locate the wireless LAN antenna connector and install the antenna.
Step 6:
Locate the signal cable of the monitor and connect one end of the cable to
the DVI port of the system. You may need to get an adapter if the supplied
signal cable isn’t DVI-interfaced.
Step 7:
Connect the other end of the signal cable to the monitor. Connect the monitor power cord to the monitor and to the power source.
2-5
▍ System Setup
Step 8:
Assemble the system power adapter and the power cord. Connect the
power adapter to the system and then connect the power cord to the power
source.
Important
We suggest that you connect the power adapter to your system first and
then connect the power cord to the socket-outlet for safety concerns.
Step 9:
Turn on the system and enjoy it.
2-6
Chapter 3
BIOS Setup
This chapter provides information on the BIOS Setup
program and allows you to configure the system for
optimum use.
You may need to run the Setup program when:
■
An error message appears on the screen
during the system booting up, and requests
you to run SETUP.
■
You want to change the default settings for
customized features.
▍ BIOS Setup
Entering Setup
Power on the computer and the system will start POST (Power On Self Test)
process. When the message below appears on the screen, press <DEL>
key to enter Setup.
Press DEL to enter SETUP
If the message disappears before you respond and you still wish to enter
Setup, restart the system by turning it OFF and On or pressing the RESET
button. You may also restart the system by simultaneously pressing <Ctrl>,
<Alt>, and <Delete> keys.
Important
The items under each BIOS category described in this chapter are under
continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for
reference only.
3-2
MS-9A45
Control Keys
←→
Select Screen
↑↓
Select Item
Enter
Select
+-
Change Option
F1
General Help
F7
Previous Values
F9
Optimized Defaults
F10
Save & Exit
Esc
Exit
Getting Help
After entering the Setup menu, the first menu you will see is the Main
Menu.
Main Menu
The main menu lists the setup functions you can make changes to. You can
use the arrow keys ( ↑↓ ) to select the item. The on-line description of the
highlighted setup function is displayed at the bottom of the screen.
Sub-Menu
If you find a right pointer symbol appears to the left of certain fields that
means a sub-menu can be launched from this field. A sub-menu contains
additional options for a field parameter. You can use arrow keys ( ↑↓ ) to
highlight the field and press <Enter> to call up the sub-menu. Then you can
use the control keys to enter values and move from field to field within a
sub-menu. If you want to return to the main menu, just press the <Esc >.
General Help <F1>
The BIOS setup program provides a General Help screen. You can call up
this screen from any menu by simply pressing <F1>. The Help screen lists
the appropriate keys to use and the possible selections for the highlighted
item. Press <Esc> to exit the Help screen.
3-3
▍ BIOS Setup
The Menu Bar
▶ Main
Use this menu for basic system configurations, such as time, date, etc.
▶ Advanced
Use this menu to set up the items of special enhanced features.
▶ Boot
Use this menu to specify the priority of boot devices.
▶ Security
Use this menu to set supervisor and user passwords.
▶ Chipset
This menu controls the advanced features of the onboard chipsets.
▶ Power
Use this menu to specify your settings for power management.
▶ Save & Exit
This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes.
3-4
MS-9A45
Main
▶ System Date
This setting allows you to set the system date. The date format is <Day>,
<Month> <Date> <Year>.
▶ System Time
This setting allows you to set the system time. The time format is <Hour>
<Minute> <Second>.
▶ SATA Mode Selection
This setting specifies the SATA controller mode.
3-5
▍ BIOS Setup
Advanced
▶ Quiet Boot
This BIOS feature determines if the BIOS should hide the normal POST
messages with the motherboard or system manufacturer’s full-screen logo.
When it is enabled, the BIOS will display the full-screen logo during the
boot-up sequence, hiding normal POST messages.
When it is disabled, the BIOS will display the normal POST messages, instead of the full-screen logo.
Please note that enabling this BIOS feature often adds 2-3 seconds of delay
to the booting sequence. This delay ensures that the logo is displayed for a
sufficient amount of time. Therefore, it is recommended that you disable this
BIOS feature for a faster boot-up time.
▶ Bootup NumLock State
This setting is to set the Num Lock status when the system is powered on.
Setting to [On] will turn on the Num Lock key when the system is powered
on. Setting to [Off] will allow users to use the arrow keys on the numeric
keypad.
3-6
MS-9A45
▶ Option ROM Messages
This item is used to determine the display mode when an optional ROM is
initialized during POST. When set to [Force BIOS], the display mode used
by AMI BIOS is used. Select [Keep Current] if you want to use the display
mode of optional ROM.
▶ CPU Configuration
▶ EIST
EIST (Enhanced Intel SpeedStep Technology) allows the system to
dynamically adjust processor voltage and core frequency, which can
result in decreased average power consumption and decreased average heat production.
▶ Hyper-Threading
The processor uses Hyper-Threading technology to increase transaction rates and reduces end-user response times. The technology treats
the two cores inside the processor as two logical processors that can
execute instructions simultaneously. In this way, the system performance is highly improved. If you disable the function, the processor will
use only one core to execute the instructions. Please disable this item if
your operating system doesn’t support HT Function, or unreliability and
instability may occur.
▶ Execute Disable Bit
Intel’s Execute Disable Bit functionality can prevent certain classes of
malicious “buffer overflow” attacks when combined with a supporting
operating system. This functionality allows the processor to classify
3-7
▍ BIOS Setup
areas in memory by where application code can execute and where it
cannot. When a malicious worm attempts to insert code in the buffer,
the processor disables code execution, preventing damage or worm
propagation.
▶ Limit CPUID Maximum
The Max CPUID Value Limit BIOS feature allows you to circumvent
problems with older operating systems that do not support the Intel
Pentium 4 processor with Hyper-Threading Technology. When enabled,
the processor will limit the maximum CPUID input value to 03h when
queried, even if the processor supports a higher CPUID input value.
When disabled, the processor will return the actual maximum CPUID
input value of the processor when queried.
▶ Super IO Configuration
▶ Serial Port 1
This setting enables/disables the specified serial port.
▶ Change Settings
This setting is used to change the address & IRQ settings of the
specified serial port.
▶ Mode Select
Select an operation mode for the serial port 1.
3-8
MS-9A45
▶ Watch Dog Timer
You can enable the system watch-dog timer, a hardware timer that generates a reset when the software that it monitors does not respond as
expected each time the watch dog polls it.
▶ H/W Monitor
These items display the current status of all monitored hardware devices/components such as voltages, temperatures and all fans’ speeds.
3-9
▍ BIOS Setup
▶ PCI/PCIE Device Configuration
▶ PCI Latency Timer
This item controls how long each PCI device can hold the bus before
another takes over. When set to higher values, every PCI device can
conduct transactions for a longer time and thus improve the effective
PCI bandwidth. For better PCI performance, you should set the item
to higher values.
▶ USB Support
This setting enables/disables support for USB devices.
▶ Legacy USB Support
Set to [Enabled] if you need to use any USB 1.1/2.0 device in the operating system that does not support or have any USB 1.1/2.0 driver
installed, such as DOS and SCO Unix.
▶ Audio Controller
This setting enables/disables the onboard audio controller.
▶ Launch PXE OpROM
This setting enables/disables the initialization of the onboard PXE
Boot ROM during bootup. Selecting [Disabled] will speed up the boot
process.
▶ Mini-PCIe Slot
This setting determines the operation mode of the Mini PCI-E slot.
3-10
MS-9A45
▶ Serial Port Console Redirection
▶ Console Redirection
Console Redirection operates in host systems that do not have a monitor and keyboard attached. This setting enables/disables the operation of console redirection. When set to [Enabled], BIOS redirects and
sends all contents that should be displayed on the screen to the serial
COM port for display on the terminal screen. Besides, all data received
from the serial port is interpreted as keystrokes from a local keyboard.
3-11
▍ BIOS Setup
Boot
▶ Boot Option #1 / #2 / #3
This setting allows users to set the sequence of boot devices where BIOS
attempts to load the disk operating system.
▶ Hard Drive BBS Priorities
This setting allows users to set the priority of the specified devices. First
press <Enter> to enter the sub-menu. Then you may use the arrow keys ( ↑
↓ ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list.
3-12
MS-9A45
Security
▶ Administrator Password
Administrator Password controls access to the BIOS Setup utility.
▶ User Password
User Password controls access to the system at boot and to the BIOS Setup
utility.
3-13
▍ BIOS Setup
Chipset
▶ IGFX - Boot Type
Use the field to select the type of device you want to use as the boot display
of the system.
▶ Fixed Graphics Memory Size
This setting specifies the size of system memory allocated for video memory.
3-14
MS-9A45
Power
▶ ACPI Sleep State
This setting specifies the power saving modes for ACPI function. If your operating system supports ACPI, you can choose to enter the Standby mode
in S1 (POS) or S3 (STR) fashion through the setting of this field.
▶ Restore AC Power Loss
This setting specifies whether your system will reboot after a power failure
or interrupt occurs. Available settings are:
[Power Off]
Leaves the computer in the power off state.
[Power On]
Leaves the computer in the power on state.
[Last State]
Restores the system to the previous status before
power failure or interrupt occurred.
3-15
▍ BIOS Setup
▶ Deep S5
The setting enables/disables the Deep S5 power saving mode. S5 is almost
the same as G3 Mechanical Off, except that the PSU still supplies power,
at a minimum, to the power button to allow return to S0. A full reboot is
required. No previous content is retained. Other components may remain
powered so the computer can “wake” on input from the keyboard, clock,
modem, LAN, or USB device.
▶ Resume On USB from S3/S4
The item allows the activity of the USB device to wake up the system from
S3/S4 sleep state.
▶ Resume On PCIE/PCI PME
This field specifies whether the system will be awakened from power saving
modes when activity or input signal of onboard PCIE/PCI PME is detected.
▶ Resume On RTC
When [Enabled], your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from suspend mode.
3-16
MS-9A45
Save & Exit
▶ Save Changes and Exit
Save changes to CMOS and exit the Setup Utility.
▶ Discard Changes and Exit
Abandon all changes and exit the Setup Utility.
▶ Restore Defaults
Restore the factory defaults.
▶ Save as User Defaults
Save all changes as user defaults.
▶ Restore User Defaults
Restore the preset user defaults.
3-17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising