ADJ Jelly par profile sys User manual

ADJ Jelly par profile sys User manual
Mega Par Profile Introduction
Unpacking: Thank you for purchasing the Mega Par Profile by American DJ®. Every Mega Par Profile has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The American DJ® Mega Par Profile is part of a continuing pursuit to create high quality intelligent lighting. The Mega Par Profile is a DMX intelligent, high powered LED par fixture. This fixture can
be used in a stand alone mode or connected in a Master/Slave configuration. This wash has five operating modes: Sound Active mode,
Auto mode, RGB mode, Static Color mode, and DMX control mode.
Customer Support: American DJ provides a customer support line,
to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit
us on the web at www.American DJ.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacific Standard Time.
Voice:
(323) 582-3322
Fax: (323) 582-3108
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
User Instructions
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ.
PLEASE recycle the shipping carton when ever possible.
6/11
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 2
Mega Par Profile General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Mega Par Profile Features
•
•
•
•
•
•
•
Mulit-Colors
Five Operating Modes
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
3-Pin DMX Connection
Seven DMX Modes: 1 Channel Mode, 2 Channel Mode, 3 Channel Mode, 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, and
7 Channel Mode.
• ADJ LED RC compatiable (Not Included)
• Power Cord Daisy Chain (See page 17)
Mega Par Profile Warranty Registration
The Mega Par Profile carries a 3 year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 3
Mega Par Profile
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 17 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 4
Mega Par Profile
Set Up
Mega Par Profile
Power Supply: The American DJ Mega Par Profile contains a automatic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
cables. Do not DMX+,DMX-,COMMON
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible.
The order
DMX512
in which fixtures are connected in a DMX line DMX+,DMX-,COMMON
does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain. COMMON
SOUND
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
1
2
3
DMX +
The Mega Par Profile can be controlled via DMX-512 protocol. The Mega
Par Profile has 7 DMX channel modes, please see page 9 for the different
modes. The DMX address is set on the back panel
of the Mega Par Profile. Your unit and your DMX
controller require a standard 3-pin XLR connector for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
Figure 1
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 5
INPUT
2
1 Ground
DMX +
3
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
XLR Male Socket
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
1
2
Figure 2
OUTPUT
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
POWER
DMX512 OUT
1
DMX512 OUT
3-PIN XLR
SOUND
3-PIN XLR
Data Cable (DMX Cable) Requirements (For
DMX Operation):
DMX -
POWER
Notice: Be sure to DMX512
follow figures two and three when making your own
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
Set Up
POWER
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
©American
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 6
Mega Par Profile
Operating Instructions
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE button until “don” is displayed, press the UP button to display “doff”. Now
the display will disappear after 10s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.
To set the display press the MODE button until “dXX” is displayed. Use
the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 10 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display can
be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
Operating Modes:
The Mega Par Profile has five operating modes:
• Sound-Active mode - The unit will react to sound, chasing through the
built in programs.
• Static Color Mode - There are 7 colors to choose from.
• Auto Mode - There are 3 Auto Modes to choose from.
• RGB Mode - Choose one of the three colors to remain static or adjust the intensity of each color to make your desired color.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the American DJ® Show Designer™.
Sound Active Mode:
In this mode the Mega Par Profile will react to sound, and chase through
the different colors.
1. Plug the fixture in and press the MODE button until “So-X” is dis-
played. “X” represents the sound active mode (1-8) currently dis-
played.
2. The fixture will now change via sound.
3. Press the SET UP button to adjust the sound sensitivity. “SJ-X” ©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 7
Mega Par Profile
Operating Instructions
should be displayed. Use the UP or DOWN buttons to adjust the
sensitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the highest.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CL-X” is displayed.
2. There are 7 colors to choose from. Select your desired color by pressing the UP and DOWN buttons. After you have selected your desired color you can activate strobing by pressing the SET UP but-
ton to enter the Flash (strobe) mode.
3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
Auto Run Mode:
There are 3 types of Auto Run Modes to choose from; Color Fade,
Color Change, and both modes running together. The running speed
is adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either “AF-X”, “AJ-X”, or “A-JF” is displayed.
• AF-X = Color Fade mode, there are 8 Color Fade modes to choose from. Use the UP or DOWN buttons to scroll through the different Auto Fade modes.
• AJ-X = Color Change mode, there are 8 Color Change modes to choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired running mode press the SET UP button until “SP.XX” is displayed. When this is displayed you can
adjust the running speed of your desired program. Use the UP or
DOWN button to adjust the speed between “SP.01” (slowest) and
“SP.16” (fastest). Once you have set your desired running speed, press the SET UP button to return to your desired Auto Run Mode.
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press the UP and DOWN buttons to adjust intensity.
3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press the ©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 8
Mega Par Profile
Operating Instructions
UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the Flash (strobe) mode.
6. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The Mega Par Profile
has 7 DMX modes: 1 Channel mode, 2 Channel mode, 3 Channel mode,
4 Channel mode, 5 Channel mode, 6 Channel mode, and a 7 Channel
mode. See pages 13-16 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until “A.XXX” is displayed. “XXX” represents the current displayed address. Use the UP or DOWN buttons to select your desired DMX address, then press the SETUP button to select your DMX Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel modes. The Channel modes are listed below:
To run the 1 Channel Mode, press the MODE button until “Ch.01” is displayed. This is the 1 Channel DMX Mode.
To run the 2 Channel Mode, press the MODE button until “Ch.02” is displayed. This is the 2 Channel DMX Mode.
To run the 3 Channel Mode, press the MODE button until “Ch.03” is displayed. This is the 3 Channel DMX Mode.
To run the 4 Channel Mode, press the MODE button until “Ch.04” is displayed. This is the 4 Channel DMX Mode.
To run the 5 Channel Mode, press the MODE button until “Ch.05” is displayed. This is the 5 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until “Ch.06” is displayed. This is the 6 Channel DMX Mode.
To run the 7 Channel Mode, press the MODE button until “Ch.07” is displayed. This is the 7 Channel DMX Mode.
4. Please see pages 13-16 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX controller.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 9
Mega Par Profile
Operating Instructions
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE button to exit.
ADJ LED RC:
This function is used to activate and deactivate the ADJ LED RC
(Remote Control). When this function is activated you can control the
fixture using the ADJ LED RC. Please see the next page for ADJ LED
RC controls and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Mega Par Profile
Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Connect the first “Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation. The “Slave” unit will now follow the “Master”.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 10
Mega Par Profile
ADJ LED RC Operation
The ADJ LED RC infrared remote (sold seperately) has many differnet
functions and gives you complete control of your Mega Par Profile.
To control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away. To use the ADJ
LED RC you must first activate the fixtures infrared receiver, to activate the receiver please see the instructions on page 10.
Blackout - Pressing this button will blackout the fixture.
Auto run - This button will run an automatic program. You can
control the speed of the Auto Run by pressing the SPEED button first
and then pressing the “+” and “-” buttons.
PROGRAM SELECTION - This button will let you access the units
built-in programs. Pressing this button and then press the “+” or “-”
to navigate through the built-in programs.
FLASH - This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
DMX MODE - This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 13-16 for DMX modes, values, and traits.
SOUND ACTIVE - This button activates sound active mode.
SLAVE - This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
R G B - Press either one of these buttons and the press the “+” or “-”
to adjust the brightness.
“+” and “-” - Use these buttons to adjust the flash rate, speed of the
Auto Run, sound sensitivity, and program selection.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 11
Mega Par Profile
ADJ LED RC Operation
DMX Control:
Operating through an DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX Mode and address.
1. Before connecting to an DMX controller, your fixture has different DMX channel modes, please select your desired mode by press-
ing the DMX Mode button, then using the “+” or “-” buttons to
scroll through the DMX Channel Modes. Set the mode before you
address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the fixture by pressing the “S” button. When the “S” button is pressed
the LED’s will flash 2-3 times and all the red LED’s will light. Use the number buttons to press in your desired address. See “SET ADDRESS” on page 11 for examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any standard DMX controller. Please see pages 13-16 to for a detailed descriptions of the DMX modes, values, and traits.
• If the Red LED’s glow you are in DMX Mode 1: 1 DMX Channel.
• If the Green LED’s glow you are in DMX Mode 2: 2 DMX
Channels.
• If the Blue LED’s glow you are in DMX Mode 3: 3 DMX
Channels.
• If the Red & Green LED’s glow you are in DMX Mode 4: 4 DMX
Channels.
• If the Red & Blue LED’s glow you are in DMX Mode 5: 5 DMX
Channels.
• If the Green & Blue LED’s glow you are in DMX Mode 6: 6 DMX
Channels.
• If all of the LED’s glow you are in DMX Mode 7: 7 DMX
Channels.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 12
Mega Par Profile
Channel
Value
Function
1-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
COLOR MACROS
BASTARD AMBER
MEDIUM AMBER
PALE AMBER GOLD
GALLO GOLD
GOLDEN AMBER
LIGHT RED
MEDIUM RED
MEDIUM PINK
BROADWAY PINK
FOLLIES PINK
LIGHT LAVENDER
SPECIAL LAVENDER
LAVENDER
INDIGO
HEMSLEY BLUE
TIPTON BLUE
LIGHT STEEL BLUE
LIGHT SKY BLUE
SKY BLUE
BRILLIANT BLUE
LIGHT GREEN BLUE
BRIGHT BLUE
PRIMARY BLUE
CONGO BLUE
PALE YELLOW GREEN
MOSS GREEN
PRIMARY GREEN
DOUBLE CTB
FULL CTB
HALF CTB
DARK BLUE
WHITE
1
©American
1 Channel - DMX Values & Functions
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 13
Mega Par Profile
Channel
2 Channel - DMX Values & Functions
Value
Function
1
1 - 255
2
1 - 255
COLOR MACROS
(See 1 Channel DMX mode for colors)
DIMMER 0% - 100%
Mega Par Profile
Channel
3 Channel - DMX Values & Functions
Value
1
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
1 - 255
2
1 - 255
3
1 - 255
Mega Par Profile
Channel
1 - 255
2
1 - 255
3
1 - 255
4
1 - 255
©American
4 Channel - DMX Values & Functions
Value
1
Function
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MASTER DIMMER
0% - 100%
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 14
Mega Par Profile
Channel
Value
5 Channel - DMX Values & Functions
Function
1
RED
1 - 255
0% - 100%
2
GREEN
1 - 255
0% - 100%
3
BLUE
1 - 255
0% - 100%
4
MASTER DIMMER
1 - 255
0% - 100%
5
1 - 255
COLOR MACROS
(See 1 Channel DMX mode for colors)
Channels 1, 2, and 3 will not work, when Channel 5 is being
used.
Mega Par Profile
Channel
Value
6 Channel - DMX Values & Functions
Mega Par Profile
Channel
1
1 - 255
2
1 - 255
3
4
1 - 255
1 - 255
5
0 - 15
16 - 255
6
0 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
Function
RED
0% - 100%
2
GREEN
1 - 255
0% - 100%
3
BLUE
1 - 255
0% - 100%
4
1 - 255
COLOR MACROS
(See 1 Channel DMX mode for colors)
5
STROBING
0 - 15
NOTHING
16 - 255
STROBING SLOW - FAST
6
MASTER DIMMER
1 - 255
0% - 100%
Channels 1, 2, and 3 will not work, when Channel 4 is being
used.
Value
1
1 - 255
7
1 - 255
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 15
7 Channel - DMX Values & Functions
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
COLOR MACROS
(See 1 Channel DMX mode for colors)
STROBING/PROGRAM SPEED
NOTHING
STROBING/SPEED CONTROL
SLOW - FAST
PROGRAMS
OFF
COLOR DREAMING 1
COLOR DREAMING 2
COLOR DREAMING 3
COLOR DREAMING 4
COLOR DREAMING 5
COLOR DREAMING 6
COLOR DREAMING 7
COLOR DREAMING 8
COLOR CHANGE 1
COLOR CHANGE 2
COLOR CHANGE 3
COLOR CHANGE 4
COLOR CHANGE 5
COLOR CHANGE 6
SOUND ACTIVE MODE 1
SOUND ACTIVE MODE 2
MASTER DIMMER
0% - 100%
Channels 1, 2, and 3 will not work, when Channel 4 is being used.
When using Channel 6 values 128-239, Channel 5 will control the speed of the programs.
When using Channel 6 values 240-255, Channel 5 will control the sound sensitivity.
©American DJ® - www.Americandj.com - Mega Par Profile User Manual Page 16
Mega Par Profile
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 33 fixtures maximum. After 33 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Mega Par Profile
Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.
Mega Par Profile
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
Mega Par Profile
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 17
Mega Par Profile
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective
parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service
and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ. All products covered by this warranty were
manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by American DJ, Inc. in connection with this product, including warranties
of merchantability or fitness, are limited in duration to the warranty period set forth above. And no
warranties, whether expressed or implied, including warranties of merchantability or fitness, shall
apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances
shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which have
a 1-year (365 day Limited Warranty)
©American DJ® - www.Americandj.com - Mega Par Profile User Manual Page 18
Mega Par Profile
Specifications
Model: Mega Par Profile
Voltage: 100V ~ 240V/50~60Hz
LEDs:
108 x 10mm LED’s (26 Red, 46 Green, & 36 Blue)
Beam Angle:
30 Degrees
Working Position: Any safe working position
Power Draw:
18W
Power Cord Daisy Chain:33 Fixtures Max.
Fuse:
0.5 Amp
Weight: 3lbs./ 1.1Kgs.
Dimensions: 9” (L) x 8.75” (W) x 3.5” (H)
225 x 220 x 85mm
Colors:
RGB Color Mixing
DMX Channels:
7 DMX Modes: 1 Channel Mode, 2 Channel Mode, 3 Channel Mode, 4 Channel Mode, 5 Channel Mode 6 Channel Mode, & 7 Channel
Mode
Warranty:
3 Year (1,095 days)
Auto Sensing Voltage: This fixture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©American
DJ® - www.Americandj.com - Mega Par Profile User Manual Page 19
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement