Christie | LX650 | LX650 Lamp and Filter Replacement Instructions

LX650 Lamp and Filter Replacement Instructions
LX650 Lamp/Filter Replacement
Instruction Sheet
INTRODUCTION
These instructions outline the details for Lamp and Filter replacement in the LX650 projector (Model
No. 103-012100-01). The lamp is located at the rear of the projector (below the input panel) and can be
accessed by removing the lamp door. NOTICE: Use only a Christie approved Lamp and Filter Kit for
your specific projector model.
KITS REQUIRED
003-120333-01 (Replacement Lamp Type No.: POA-LMP108)
003-001726-01 (Replacement Air Filter)
INSTRUCTIONS
DANGER
Do not drop the lamp assembly or touch a glass bulb! The glass can shatter and may
cause injury.
DANGER
Disconnect all power sources to the projector before opening lamp cover.
WARNING
Allow a projector to cool, for at least 45 minutes before you open Lamp Cover. The
inside of a projector can become very hot.
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
1 of 6
LAMP REPLACEMENT PROCEDURE
When the projection lamp of the projector reaches its end of life, the Lamp
Top Panel
Replacement icon
appears on the screen and LAMP REPLACE indicator
lights orange (Figure 1). Replace the lamp with a new one promptly. The
timing when the LAMP REPLACE indicator should light is dependent on the
lamp mode. NOTICE: For continued safety, replace with a lamp assembly of
the same type.
LAMP REPLACE Indicator
Figure 1 Top Panel
Indicator
1. Turn off the projector and unplug the AC Power Cord. Let
the projector cool for at least 45 minutes. CAUTION: The
inside of the projector can become very hot.
2. Open the Filter Cover.
3. Loosen the screw and open then Lamp Cover (see Figure 2).
4. Pull out the lamp by using the built-in handle.
5. Replace the Lamp with a new one. Make sure the Lamp is
set properly and fully inserted. NOTES:1) Make sure
replace the lamp with a lamp of the same type. 2) Insert
lamp in proper direction.
6. Close the Lamp Cover, secure screw, and close the Filter
Door.
7. Connect the AC Power Cord to the projector and turn on the
projector.
8. Reset the Lamp Replacement Counter (see below). NOTE:
Do not reset LAMP REPLACEMENT COUNTER when lamp
is not replaced.
Figure 2 Lamp Replacement
2 of 6
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
DANGER
Do Not Operate a projector while any lamp is removed. This may result in malfunctions,
fire hazard, or other accidents.
RESETTING THE LAMP COUNTER
Reset the Lamp counter after the lamp is replaced. This will turn off the LAMP REPLACE indicator
and the Lamp replacement icon will disappear.
1. Press the MENU button to display the
On-Screen Menu. Use the
buttons to
move the red frame pointer to the Setting
Menu icon
2. Use the
buttons to move the red
frame pointer to Lamp counter and then
press the SELECT button. A dialog box
appears. Select a lamp and the “Lamp
replacement counter Reset?” appears.
Select [Yes] to continue.
3. Another confirmation dialog box appears
and select [Yes] to reset the Lamp
counter.
NOTE: Do not reset the Lamp counter
without replacing the lamp and only after
replacing the lamp.
Select Reset and the “Lamp
replacement counter Reset?”
appears.
Select [Yes], then another
confirmation box appears.
Select [Yes] again
to reset the lamp
counter.
Figure 3 Reset Lamp Counter
HOW TO CHECK LAMP USED TIME
The LAMP REPLACE indicator will light yellow when the
total lamp used time (Corresponding value) reaches 3,000
Projector used time
hours. This is to indicate that lamp replacement is required.
Lamp mode
The total lamp used time is calculated by using the below
expression,
Total lamp used time (Corresponding value) = Teco +
(Tnormal x 1.5)
• Teco: used time in the Eco mode
• Tnormal: used time in the Normal mode
Total lamp used time
Figure 4 Lamp Used Time
You can check the lamp used time following to the below
procedure.
1. Press and hold the ON/STAND-BY button on the projector for more than 20 seconds.
2. The projector used time and lamp used time will be displayed on the screen briefly as follows.
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
3 of 6
FILTER CARE/REPLACEMENT PROCEDURE
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter
become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal
heat buildup and adversely affect the life of the projector. If a Filter Warning icon
screen, clean the filter immediately.
appears on the
1. Turn off the projector, and unplug the AC power cord from
the AC outlet.
2. First, clean up the dust on the projector and around the air
vents.
3. Press on the filter cover to release the latch and open the
filter cover.
4. Pull out the filter cartridge. When taking out the filter
cartridge, put your finger on the filter cartridge’s tab and then
pull.
5. Put the new one back into the position and close the filter
cover. Make sure that the filter cartridge is properly and fully
inserted.
6. Connect the AC power cord to the projector and turn on the
projector.
7. Reset the filter counter and the scroll counter.
NOTICES: 1) Do not operate the projector with the Air Filter
removed. Dust may accumulate on the optical elements degrading
the picture quality. 2) Do not put anything into the air intake
vents. Doing so may result in a malfunction of the projector.
Failure to properly clean the projector's air filters (in accordance
with the instructions in your Projector's Operating Manual, or
more frequently in any environment which is somewhat dusty or
smoky) could result in overheating and will void the warranty on
the projector.
NOTES: 1) If the filter is heavily clogged and unable to clean,
replace it with a new one. Please consult your dealer for details.
2) Do not wash the filter with water or any other liquid matter.
RECOMMENDATIONS: 1) We recommend avoiding dusty/
smoky environments when operating the projector. Usage in these
environments may cause a poor image quality. 2) When using the
projector under dusty or smoky conditions, dust may accumulate
on a lens, liquid crystal panels, or optical elements inside the
projector. Such condition may degrade the quality of the projected
image. 3) When the symptoms above are noticed, contact your
authorized dealer or service station for proper cleaning.
4 of 6
Figure 5 Replace Filter
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
RESETTING THE FILTER COUNTER
Be sure to reset the Filter counter after cleaning
or replacing the filter.
1. Press the MENU button to display the OnScreen Menu. Use the
buttons to move
the red frame pointer to the Setting Menu
icon.
2. Use the
buttons to move the red frame
pointer to Filter counter and then press the
SELECT button. A dialog box appears
showing the Used Time option you can
scroll to view the remaining Time options.
Use the
buttons to select Used time.
3. Used Time shows the total accumulated time
of the filter use, a Timer Setting option, and
the Reset option. Select Reset and the “Filter
counter Reset?” appears. Select [Yes] to
continue.
4. Another confirmation dialog box appears,
select [Yes] to reset the Filter counter.
NOTE: Do not reset the Filter Counter without
replacing the filter and only after replacing the
filter.
Select “Used time” and the dialogue
box below appears.
Select Reset and the “Filter
counter Reset?” appears.
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Filter counter.
Figure 6 Reset Filter Counter
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
5 of 6
RESETTING THE SCROLL COUNTER
Be sure to reset the Scroll counter after replacing
the filter cartridge.
1. Press the MENU button to display the OnScreen Menu. Use the
buttons to move
the red frame pointer to the Setting Menu
icon.
2. Use the Point
buttons to move the red
frame pointer to Filter counter and then
press the SELECT button. A dialog box
appears showing the Used Time option you
can scroll to view the remaining Time
options. Use the Point
buttons to select
Scroll(s) remaining.
3. Scroll(s) remaining shows the number of the
remaining scrolls and the Reset option.
Select Reset and the “Scroll counter Reset?”
appears. Select [Yes] to continue.
4. Another confirmation dialog box appears,
select [Yes] to reset the Filter counter.
Select “Scrolls remaining” and
the dialogue box below appears.
Select Reset and the “Scroll
counter Reset?” appears.
Select [Yes],
then another
confirmation
box appears.
Select [Yes] again to reset
the Scroll counter.
Figure 7 Reset Scroll Counter
6 of 6
LX1500 Lamp/Filter Replacement Instruction Sheet
020-000023-01 Rev. 1 (12/07)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising